IGD841 Hybrid Integrated Isolated N-Channel IGBT Driver Electrical Specifications Key Features: Absolute Maximum Ratings, TA = 25 ºC unless otherwise noted. • Internal OptoCoupler • 30 kV/µS CMR • VISO = 3,750V • One Supply Drive Topology • Compact SIP Package • Short Circuit Protected • Fault Signal Output • Switching Freq. to 20 kHz • Compatible With EXB841 Parameter Recommended For: Conditions Min. VCC DC 25 VDC VIN See Note 3 50 VDC IIN See Note 4 25 mA Input Current IGON Output Current IGOFF Isolation Voltage VISO Junction Temperature TJ Operating Temperature TOP Storage Temperature TST Supply Voltage VCC Recommended Range VRB Recommended Range f Recommended Range IIH Recommended Range A 3,750 VAC 150 ºC -20 +70 ºC -40 +125 ºC 20 mA Max. Units Min. Typ. 14 15 VDC -5 VDC 0 20 kHz ⍀ 2 RG Input CMR “H” Input Current -5.0 Sine Wave Voltage 50 Hz/ 60 Hz , 1 Min Reverse Bias Supply Voltage Gate Resistor +5.0 Pulse Width 2µS, Frequency ⬉ 20 kHz Conditions Switching Frequency 15 30 10 16 kV/µS 20 mA “H” Output Voltage VOH VCC = 20V 14 VDC “L” Output Voltage VOL VCC = 20V -5 VDC “L-H” Propagation TPLH IIH = 16 mA 0.5 1.0 µS TR IIH = 16 mA 0.6 1.0 µS TPHL IIH = 16 mA 1.0 1.3 µS TF IIH = 16 mA 0.4 1.0 µS VOCP VCC = 20V 8.5 “L-H” Rise Time “H-L” Propagation “H-L” Fall Time Protection Threshold Voltage Protection Reset Time T: (781) 344-8226 F: (781) 344-8481 E: [email protected] W: www.micropowerdirect.com Units Supply Voltage Parameter 292 Page Street Suite D Stoughton, MA 02072 USA Max. Input Voltage • 600V Series IGBT (up to 600A) Fault Output Current IFO See Note 5 • 1200V Series IGBT (up to 400A) Electrical Characteristics, TA = 25 ºC, VCC = 15 VDC unless otherwise noted. • 1700V Series IGBT (up to 200A) MicroPower Direct Typ. Fault Output Current TTIMER IFO 1.0 1.4 See Note 6 VDC 2.0 mS 5.0 mA Controlled Time Detect TTRIP1 Short Circuit 1, See Note 7 2.6 µS Soft Turn-Off Time TOFF2 See Note 8 5.0 µS SC Detect Voltage VSC Collector Voltage of Module 15 Notes: 1. Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings. 2. ”H” = high level signal. “L” = low level signal. 3. The voltage applied to pin 15. 4. The current measured between pins 15 and 14. 5. The current at pin 5. 6. The current at pin 5. R2 = 4.7 k⍀. 7. Pin 6 ⭌ 15 VDC. 8. Pin 6 ⭌ 15 VDC. www.micropowerdirect.com VDC www.micropowerdirect.com Typical Connection Connection Notes: To minimize the potential for problems (and/or failures) caused by induced noise, EMI interference and/or oscillation, the connection of the gate driver must be done with great care. Some recommendations would include: 1. The input signal voltage (pin 14) cannot exceed 5.25V. The internal dissipation caused by the resultant increase in input current could damage the input optocoupler. A current limiting resistor (R1) is used to help prevent this. The resistor value is calculated by the formula: R1 = VIN - 1.7V - 150X 16 mA 2. 3. 4. 5. 6. 7. 8. 9. The gate wiring of the IGBT gate-emitter drive loop must be shorter than 1 meter. Twisted pair wiring is recommended for the gate-emitter drive loop to minimize mutual induction. Pins 4, 7, 8, 10 and 11 (not shown in the connection diagram) of the IGD841 are only used for testing. They should not be used as a connection in any application circuit. If a large voltage spike is generated at the IGBT collector, the value of the gate resistor (RG) should be increased. Smoothing capacitors C2 and C3 should be mounted as close to the driver as possible. An internal circuit sets up a -5V off-gate voltage at pin 9 to protect against faults in the off state. Do not apply an external voltage to pin 1. The peak reverse voltage rating of D1 must be higher than the peak value of the IGBT collector voltage. The traces (or wires) between the power source (VCC) and the driver circuit should be as short as possible. Pin Connections Mechanical Dimensions Pin Function Pin Function 1 2 3 Smoothing Capacitor Power Supply (+) Drive Output 5 6 9 Fault Signal Output Fault Detect Gnd MicroPower Direct Pin Function 14 Drive Signal Input (-) 15 Drive Signal Input (+) 4,7,8,10,11 No Connection Notes: • All dimensions are typical in inches (mm) • Tolerance x.xx = ±0.01 (±0.25) We Power Your Success - For Less! 292 Page Street Ste D Stoughton, MA 02072 • TEL: (781) 344-8226 • FAX: (781) 344-8481 • E-Mail: [email protected]