NL27WZ08 Dual 2-Input AND Gate The NL27WZ08 is a high performance dual 2–input AND Gate operating from a 1.65 V to 5.5 V supply. • • • • • • • • • Extremely High Speed: tPD 2.5 ns (typical) at VCC = 5 V Designed for 1.65 V to 5.5 V VCC Operation Over Voltage Tolerant Inputs LVTTL Compatible – Interface Capability With 5 V TTL Logic with VCC = 3 V LVCMOS Compatible 24 mA Balanced Output Sink and Source Capability Near Zero Static Supply Current Substantially Reduces System Power Requirements Replacement for NC7WZ08 Chip Complexity: FET = 124 http://onsemi.com MARKING DIAGRAM 8 8 1 L2 US8 US SUFFIX CASE 493 D 1 D = Date Code A1 1 8 VCC B1 2 7 Y1 ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 4 of this data sheet. Y2 GND 6 3 5 4 B2 IEEE/IEC A1 B1 A2 & Y1 A2 B2 Figure 1. Pinout Y2 Figure 2. Logic Symbol PIN ASSIGNMENT FUNCTION TABLE Pin Function 1 A1 2 B1 3 Y2 4 GND 5 A2 6 B2 7 Y1 8 VCC Semiconductor Components Industries, LLC, 2002 July, 2002 – Rev. 2 Y = AB Inputs Output A B Y L L L L H L H L L H H H H = HIGH Logic Level L = LOW Logic Level 1 Publication Order Number: NL27WZ08/D NL27WZ08 MAXIMUM RATINGS Symbol Parameter Value Unit VCC DC Supply Voltage 0.5 to 7.0 V VI DC Input Voltage 0.5 to 7.0 V VO DC Output Voltage 0.5 to VCC + 0.5 V IIK DC Input Diode Current VI < GND 50 mA IOK DC Output Diode Current VO < GND 50 mA IO DC Output Sink Current 50 mA ICC DC Supply Current per Supply Pin 100 mA IGND DC Ground Current per Ground Pin 100 mA TSTG Storage Temperature Range 65 to 150 °C TL Lead Temperature, 1 mm from Case for 10 Seconds TJ Junction Temperature under Bias JA Thermal Resistance PD Power Dissipation in Still Air at 85°C MSL Moisture Sensitivity FR Flammability Rating VESD ESD Withstand Voltage Human Body Model (Note 2) Machine Model (Note 3) Charged Device Model (Note 4) > 2000 > 200 N/A V ILatch–Up Latch–Up Performance Above VCC and Below GND at 85°C (Note 5) 500 mA (Note 1) 260 °C 150 °C 250 °C/W 250 mW Level 1 Oxygen Index: 28 to 34 UL 94 V–0 @ 0.125 in Maximum Ratings are those values beyond which damage to the device may occur. Exposure to these conditions or conditions beyond those indicated may adversely affect device reliability. Functional operation under absolute maximum–rated conditions is not implied. Functional operation should be restricted to the Recommended Operating Conditions. 1. Measured with minimum pad spacing on an FR4 board, using 10 mm–by–1 inch, 2–ounce copper trace with no air flow. 2. Tested to EIA/JESD22–A114–A. 3. Tested to EIA/JESD22–A115–A. 4. Tested to JESD22–C101–A. 5. Tested to EIA/JESD78. RECOMMENDED OPERATING CONDITIONS Symbol Parameter VCC Supply Voltage VI Input Voltage VO Output Voltage TA Operating Free–Air Temperature t/V Input Transition Rise or Fall Rate Min Max Unit 1.65 1.5 5.5 5.5 V (Note 6) 0 5.5 V (HIGH or LOW State) 0 VCC V 40 85 °C 0 0 0 20 10 5 ns/V Operating Data Retention Only VCC = 2.5 V 0.2 V VCC = 3.0 V 0.3 V VCC = 5.0 V 0.5 V 6. Unused inputs may not be left open. All inputs must be tied to a high– or low–logic input voltage level. http://onsemi.com 2 NL27WZ08 DC ELECTRICAL CHARACTERISTICS Symbol Parameter Condition 40C TA 85C TA = 25C VCC (V) Min 0.75 VCC 0.7 VCC VIH High–Level Input Voltage 1.65 2.3 to 5.5 VIL Low–Level Input Voltage 1.65 2.3 to 5.5 VOH High Level Output High–Level Out ut Voltage VIN = VIL or VIH IOH = 100 A IOH = –3 mA IOH = –8 8 mA A IOH = –12 mA IOH = –16 mA IOH = –24 24 mA IOH = –32 32 mA A 1.65 to 5.5 165 23 2.3 27 2.7 3.0 3.0 45 4.5 VOL Low Level Output Low–Level Out ut Voltage VIN = VIH or VOH IOL = 100 A IOL = 3 mA IOL = 8 mA A IOL = 12 mA IOL = 16 mA IOL = 24 mA IOL = 32 mA A 1.65 to 5.5 Typ Max Min 0.75 VCC 0.7 VCC 0.25 VCC 0.3 VCC VCC – 0.1 1.29 19 1.9 22 2.2 2.4 2.3 38 3.8 VCC 1.5 21 2.1 24 2.4 2.7 2.5 40 4.0 0.08 0 20 0.20 0 22 0.22 0.28 0.38 0 42 0.42 23 2.3 27 2.7 3.0 3.0 45 4.5 Max Unit V 0.25 0.3 VCC VCC – 0.1 1.5 19 1.9 22 2.2 2.4 2.3 38 3.8 V V 0.1 0.24 03 0.3 04 0.4 0.4 0.55 0 55 0.55 0.1 0.24 03 0.3 04 0.4 0.4 0.55 0 55 0.55 V IIN Input Leakage Current VIN = VCC or GND 0 to 5.5 0.1 1.0 A ICC Quiescent Supply Current VIN = VCC or GND 5.5 1.0 10 A AC ELECTRICAL CHARACTERISTICS tR = tF = 3.0 ns Symbol tPLH tPHL Condition (V) Min RL = 1 M CL = 15 pF 1.8 0.15 2.0 5.7 10.5 2.0 11.0 2.5 0.2 1.0 3.5 5.8 2.0 6.2 RL = 1 M CL = 15 pF F RL = 500 CL = 50 pF 3.3 0.3 0.8 1.2 2.6 3.2 3.9 4.8 0.8 1.2 4.3 5.2 RL = 1 M CL = 15 pF F RL = 500 CL = 50 pF 5.0 0.5 0.5 0.8 1.9 2.5 3.1 3.7 0.5 0.8 3.3 4.0 Parameter Propagation Delay (Figure 3 and 4) 40C TA 85C TA = 25C VCC Typ Max Min Max Unit ns CAPACITIVE CHARACTERISTICS Symbol Parameter Condition Typical Unit CIN Input Capacitance VCC = 5.5 V, VI = 0 V or VCC 4 pF CPD Power Dissipation Capacitance (Note 7) 10 MHz, VCC = 3.3 V, VI = 0 V or VCC 10 MHz, VCC = 5.5 V, VI = 0 V or VCC 25 30 pF 7. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin + ICC. CPD is used to determine the no–load dynamic power consumption; PD = CPD VCC2 fin + ICC VCC. http://onsemi.com 3 NL27WZ08 tf = 3 ns tf = 3 ns 90% INPUT A and B 50% VCC VCC 90% 50% 10% 10% tPHL GND RL tPLH CL VOH OUTPUT Y 50% 50% A 1–MHz square input wave is recommended for propagation delay tests. VOL Figure 3. Switching Waveform Figure 4. Test Circuit DEVICE ORDERING INFORMATION Device Nomenclature Device Order Number NL27WZ08US Logic Circuit Indicator No. of Gates per Package Temp Range Identifier Technology Device Function Package Suffix Package Type Tape and Reel Size NL 2 7 WZ 08 US US8 178 mm, 3000 Unit http://onsemi.com 4 NL27WZ08 CAVITY TAPE TOP TAPE TAPE TRAILER (Connected to Reel Hub) NO COMPONENTS 160 mm MIN COMPONENTS TAPE LEADER NO COMPONENTS 400 mm MIN DIRECTION OF FEED Figure 5. Tape Ends for Finished Goods TAPE DIMENSIONS mm 4.00 1.50 TYP 4.00 2.00 1.75 3.50 0.25 0.30 8.00 + – 0.10 1 1.00 ± 0.25 TYP DIRECTION OF FEED Figure 6. US8 Reel Configuration/Orientation http://onsemi.com 5 NL27WZ08 t MAX 1.5 mm MIN (0.06 in) A 13.0 mm 0.2 mm (0.512 in 0.008 in) 50 mm MIN (1.969 in) 20.2 mm MIN (0.795 in) FULL RADIUS G Figure 7. Reel Dimensions REEL DIMENSIONS Tape Size T and R Suffix A Max G t Max 8 mm US 178 mm (7 in) 8.4 mm, + 1.5 mm, –0.0 (0.33 in + 0.059 in, –0.00) 14.4 mm (0.56 in) DIRECTION OF FEED BARCODE LABEL POCKET Figure 8. Reel Winding Direction http://onsemi.com 6 HOLE NL27WZ08 PACKAGE DIMENSIONS US8 US SUFFIX CASE 493–01 ISSUE O NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETERS 3. DIMENSION A" DOES NOT INCLUDE MOLD FLASH, PROTRUSION OR GATE BURR. MOLD FLASH. PROTRUSION AND GATE BURR SHALL NOT EXCEED 0.140 MM (0.0055") PER SIDE. 4. DIMENSION B" DOES NOT INCLUDE INTER-LEAD FLASH OR PROTRUSION. INTER-LEAD FLASH AND PROTRUSION SHALL NOT E3XCEED 0.140 (0.0055") PER SIDE. 5. LEAD FINISH IS SOLDER PLATING WITH THICKNESS OF 0.0076-0. 0203 MM. (300-800 INCH). 6. ALL TOLERANCE UNLESS OTHERWISE SPECIFIED ±0.0508 (0.0002"). –X– A 8 J –Y– 5 DETAIL E B L 1 4 R S G P U C –T– SEATING PLANE H 0.10 (0.004) T K D N 0.10 (0.004) M T X Y R 0.10 TYP V M F DETAIL E 3.8 0.5 TYP ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ 1.8 TYP ÉÉÉ ÉÉÉ ÉÉÉ ÉÉÉ 1.0 http://onsemi.com 7 0.3 TYP (mm) DIM A B C D F G H J K L M N P R S U V MILLIMETERS MIN MAX 1.90 2.10 2.20 2.40 0.60 0.90 0.17 0.25 0.20 0.35 0.50 BSC 0.40 REF 0.10 0.18 0.00 0.10 3.00 3.20 0 6 5 10 0.28 0.44 0.23 0.33 0.37 0.47 0.60 0.80 0.12 BSC INCHES MIN MAX 0.075 0.083 0.087 0.094 0.024 0.035 0.007 0.010 0.008 0.014 0.020 BSC 0.016 REF 0.004 0.007 0.000 0.004 0.118 0.126 0 6 5 10 0.011 0.017 0.009 0.013 0.015 0.019 0.024 0.031 0.005 BSC NL27WZ08 ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. PUBLICATION ORDERING INFORMATION Literature Fulfillment: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303–675–2175 or 800–344–3860 Toll Free USA/Canada Fax: 303–675–2176 or 800–344–3867 Toll Free USA/Canada Email: [email protected] JAPAN: ON Semiconductor, Japan Customer Focus Center 4–32–1 Nishi–Gotanda, Shinagawa–ku, Tokyo, Japan 141–0031 Phone: 81–3–5740–2700 Email: [email protected] ON Semiconductor Website: http://onsemi.com For additional information, please contact your local Sales Representative. N. American Technical Support: 800–282–9855 Toll Free USA/Canada http://onsemi.com 8 NL27WZ08/D