Thin Film Directional Couplers Wide Band High Directivity CP0402W2700FNTR ITF TECHNOLOGY The ITF High Directivity Wide Band LGA Coupler is based on thinfilm multilayer technology. The technology provides a miniature part with excellent high frequency performance and rugged construction for reliable automatic assembly. The Wide Band High Directivity Coupler displays a stable coupling factor over a wide frequency band. APPLICATIONS • • • • • LAND GRID ARRAY ADVANTAGES Mobile communications Satellite TV receivers GPS Vehicle location systems Wireless LAN’s • Inherent Low Profile • Self Alignment during Reflow • Excellent Solderability • Low Parasitics • Better Heat Dissipation DIMENSIONS (Bottom View) HOW TO ORDER CP 0402 W XXXX B X N TR SubType LGA Termination Sn100 Taped & Reeled S H mm (inches) L W A T Type Frequency Wide (MHz) Band L A T B QUALITY INSPECTION Finished parts are 100% tested for electrical parameters and visual characteristics. Each production lot is evaluated on a sample basis for: • Static Humidity: 85°C, 85% RH, 160 hours • Endurance: 125°C, IR, 4 hours W S, H 1.00±0.05 (0.040±0.002) 0.58±0.04 (0.023±0.002) 0.35±0.05 (0.014±0.002) 0.20±0.05 (0.008±0.002) 0.18±0.05 (0.007±0.002) 0.05±0.05 (0.002±0.002) TERMINALS (Top View) Coupling GND TERMINATION Nickel/Lead Free solder coating compatible with automatic soldering technologies: reflow, wave soldering, vapor phase and manual. OPERATING TEMPERATURE IN Out White Mark Recommended Pad Layout Dimensions -40°C to +85°C mm (inches) 0.31 (0.012) 0.20 (0.008) 0.15 (0.006) 0.53 (0.021) 1 Thin Film Directional Couplers Wide Band High Directivity CP0402W2700FNTR P/N Frequency [MHz] Coupling [dB] CP0402W2700FNTR 700-2,700 24±2 I. Loss max. [dB] 0.3 Return Loss [dB] 18 Directivity [dB] 0 20 0 -10 -2 -20 -4 -30 -6 -40 -8 -50 -10 -60 -12 3,000 500 1,000 1,500 2,000 2,500 I Loss dB Coupling R Loss Isolation dB Directional Coupler Type CP0402W2700FNTR Frequency MHz 2 Thin Film Directional Couplers Wide Band High Directivity CP0402W2700FNTR Test Jigs GENERAL DESCRIPTION These jigs are designed for testing the CP0402W2700FNTR High Directivity Couplers using a Vector Network Analyzer. They consist of a dielectric substrate, having 50Ω microstrips as conducting lines and a bottom ground plane located at a distance of 0.254mm (0.010") from the microstrips. The substrate used is Neltec’s NH9338ST0254C1BC. The connectors are SMA type (female), ‘Johnson Components Inc.’ Product P/N: 142-0701-841. Both a measurement jig and a calibration jig are provided. The calibration jig is designed for a full 2-port calibration, and consists of an open line, short line and through line. LOAD calibration can be done by a 50Ω SMA termination. MEASUREMENT PROCEDURE When measuring a component, it can be either soldered or pressed using a non-metallic stick until all four ports touch the appropriate pads. Set the VNA to the relevant frequency band. Connect the VNA using a 10dB attenuator on the jig terminal connected to port 2. Follow the VNA’s instruction manual and use the calibration jig to perform a full 2-Port calibration in the required bandwidths. Place the coupler on the measurement jig as follows: GND (Coupler) ➜ Connector 1 (Jig) Coupling (Coupler) ➜ Connector 2 (Jig) IN (Coupler) ➜ Connector 3 (Jig) Out (Coupler) ➜ Connector 4 (Jig) To measure I. Loss connect: Connector 3 (Jig) ➜ Port 1 (VNA) Connector 4 (Jig) ➜ Port 2 (VNA) Connector 2 (Jig) ➜ 50Ω To measure R. Loss and Coupling connect: Connector 3 (Jig) ➜ Port 1 (VNA) Connector 2 (Jig) ➜ Port 2 (VNA) Connector 4 (Jig) ➜ 50Ω To measure Isolation connect: Connector 4 (Jig) ➜ Port 1 (VNA) Connector 3 (Jig) ➜ 50Ω Connector 2 (Jig) ➜ Port 2 (VNA) Measurement Jig Connector 1 (not used) Short Line to GND. OPEN TH TH Open Line Connector 4 Connector 3 3 Connector Johnson P/N 142-0701-841 HS Connector 2 HS OPEN Calibration Jig Load & Through Load & Through