STMicroelectronics M27V322-150XB1 32 mbit (2mb ã 16) low-voltage uv eprom and otp eprom Datasheet

M27V322
32 Mbit (2Mb ×16) low-voltage UV EPROM and OTP EPROM
Feature summary
■
3.3V ± 10% supply voltage in Read operation
■
Read access time
– 100ns at VCC = 3.0V to 3.6V
■
Pin compatible with M27C322
■
Word-wide configurable
■
32 Mbit Mask ROM replacement
■
Low power consumption
– Active Current 30mA at 5MHz
– Stand-by Current 60µA
■
Programming voltage: 12V ± 0.25V
■
Programming time: 50µs/word
■
Electronic signature
– Manufacturer Code: 0020h
– Device Code: 0034h
42
1
■
FDIP42W (F)
42
1
ECOPACK® packages available
PDIP42 (B)
42
1
SDIP42 (S)
May 2006
Rev 3
1/23
www.st.com
1
Contents
M27V322
Contents
1
Summary description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
2
Device operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.1
Read mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.2
Standby mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.3
Two Line Output Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
2.4
System considerations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.5
Programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.6
PRESTO III programming algorithm . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8
2.7
Program Inhibit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.8
Program Verify . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.9
On-Board programming . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
2.10
Electronic Signature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
2.11
Erasure operation (applies to UV EPROM) . . . . . . . . . . . . . . . . . . . . . . . 10
3
Maximum rating . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
4
DC and AC parameters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
5
Package mechanical . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
6
Part numbering . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
7
Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
2/23
M27V322
List of tables
List of tables
Table 1.
Table 2.
Table 3.
Table 4.
Table 5.
Table 6.
Table 7.
Table 8.
Table 9.
Table 10.
Table 11.
Table 12.
Table 13.
Table 14.
Table 15.
Table 16.
Signal names . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Operating modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Electronic signature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Absolute maximum ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
AC measurement conditions. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Capacitance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Read mode DC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Programming mode DC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Read mode AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Margin mode AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Programming mode AC characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
FDIP42W - 42 pin Ceramic Frit-seal DIP, with window (0.315" × 0.630"),
mechanical data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
PDIP42 - 42 pin Plastic DIP, 600 mils width, package mechanical data . . . . . . . . . . . . . . 19
SDIP42 - 42 lead Shrink Plastic DIP, 600 mils width, package mechanical data . . . . . . . . 20
Ordering information scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Document revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
3/23
List of figures
M27V322
List of figures
Figure 1.
Figure 2.
Figure 3.
Figure 4.
Figure 5.
Figure 6.
Figure 7.
Figure 8.
Figure 9.
Figure 10.
Figure 11.
4/23
Logic diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
DIP connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Programming flowchart . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9
AC testing input output waveform . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
AC testing load circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13
Read mode AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Margin mode AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Programming and Verify modes AC waveforms . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
FDIP42W - 42 pin Ceramic Frit-seal DIP, with window (0.315" × 0.630"),
package outline. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
PDIP42 - 42 pin Plastic DIP, 600 mils width, package outline . . . . . . . . . . . . . . . . . . . . . . 19
SDIP42 - 42 pin Shrink Plastic DIP, 600 mils width, package outline. . . . . . . . . . . . . . . . . 20
M27V322
1
Summary description
Summary description
The M27V322 is a 32 Mbit EPROM offered in the UV range (ultra violet erase) and OTP
range. It is ideally suited for microprocessor systems requiring large data or program
storage. It is organised as 2 MWords of 16 bit. The pin-out is compatible with a 32 Mbit Mask
ROM.
The FDIP42W (window ceramic frit-seal package) has a transparent lid which allows the
user to expose the chip to ultraviolet light to erase the bit pattern. A new pattern can then be
written rapidly to the device by following the programming procedure.
For applications where the content is programmed only one time and erasure is not
required, the M27V322 is offered in PDIP42 and SDIP42 packages.
In order to meet environmental requirements, ST offers the M27V322 in ECOPACK®
packages.
ECOPACK packages are Lead-free. The category of second Level Interconnect is marked
on the package and on the inner box label, in compliance with JEDEC Standard JESD97.
The maximum ratings related to soldering conditions are also marked on the inner box label.
ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com.
Figure 1.
Logic diagram
VCC
21
16
A0-A20
E
Q0-Q15
M27V322
GVPP
VSS
AI03050
Table 1.
Signal names
A0-A20
Address Inputs
Q0-Q15
Data Outputs
E
Chip Enable
GVPP
Output Enable / Program Supply
VCC
Supply Voltage
VSS
Ground
5/23
Summary description
Figure 2.
M27V322
DIP connections
A18
A17
A7
A6
A5
A4
A3
A2
A1
A0
E
VSS
GVPP
Q0
Q8
Q1
Q9
Q2
Q10
Q3
Q11
1
42
41
2
40
3
39
4
38
5
37
6
36
7
8
35
9
34
10
33
M27V322
11
32
12
31
13
30
14
29
15
28
16
27
17
26
18
25
19
24
20
23
21
22
AI03051
6/23
A19
A8
A9
A10
A11
A12
A13
A14
A15
A16
A20
VSS
Q15
Q7
Q14
Q6
Q13
Q5
Q12
Q4
VCC
M27V322
2
Device operation
Device operation
The operating modes of the M27V322 are listed in the Operating Modes Table. A single
power supply is required in the read mode. All inputs are TTL compatible except for VPP and
12V on A9 for the Electronic Signature.
2.1
Read mode
The M27V322 has a word-wide organization. Chip Enable (E) is the power control and
should be used for device selection. Output Enable (G) is the output control and should be
used to gate data to the output pins independent of device selection. Assuming that the
addresses are stable, the address access time (tAVQV) is equal to the delay from E to output
(tELQV). Data is available at the output after a delay of tGLQV from the falling edge of GVPP,
assuming that E has been low and the addresses have been stable for at least tAVQV-tGLQV.
2.2
Standby mode
The M27V322 has a standby mode which reduces the supply current from 30mA to 30µA.
The M27V322 is placed in the standby mode by applying a CMOS high signal to the E
input.When in the standby mode, the outputs are in a high impedance state, independent of
the GVPP input.
2.3
Two Line Output Control
Because EPROMs are usually used in larger memory arrays, this product features a 2 line
control function which accommodates the use of multiple memory connection. The two line
control function allows:
●
the lowest possible memory power dissipation,
●
complete assurance that output bus contention will not occur.
For the most efficient use of these two control lines, E should be decoded and used as the
primary device selecting function, while GVPP should be made a common connection to all
devices in the array and connected to the READ line from the system control bus. This
ensures that all deselected memory devices are in their low power standby mode and that
the output pins are only active when data is required from a particular memory device.
7/23
Device operation
2.4
M27V322
System considerations
The power switching characteristics of Advanced CMOS EPROMs require careful
decoupling of the supplies to the devices. The supply current ICC has three segments of
importance to the system designer: the standby current, the active current and the transient
peaks that are produced by the falling and rising edges of E. The magnitude of the transient
current peaks is dependent on the capacitive and inductive loading of the device outputs.
The associated transient voltage peaks can be suppressed by complying with the two line
output control and by properly selected decoupling capacitors. It is recommended that a
0.1µF ceramic capacitor is used on every device between VCC and VSS. This should be a
high frequency type of low inherent inductance and should be placed as close as possible to
the device. In addition, a 4.7µF electrolytic capacitor should be used between VCC and VSS
for every eight devices. This capacitor should be mounted near the power supply connection
point. The purpose of this capacitor is to overcome the voltage drop caused by the inductive
effects of PCB traces.
2.5
Programming
When delivered (and after each erasure for UV EPROM), all bits of the M27V322 are in the
"1" state. Data is introduced by selectively programming "0"s into the desired bit locations.
Although only "0"s will be programmed, both "1"s and "0"s can be present in the data word.
The only way to change a "0" to a "1" is by die exposition to ultraviolet light (UV EPROM).
The M27V322 is in the programming mode when VPP input is at 12.V, GVPP is at VIH and E
is pulsed to VIL. The data to be programmed is applied to 16 bits in parallel to the data
output pins. The levels required for the address and data inputs are TTL. VCC is specified to
be 6.25V ± 0.25V.
2.6
PRESTO III programming algorithm
The PRESTO III Programming Algorithm allows the whole array to be programed with a
guaranteed margin in a typical time of 100 seconds. Programming with PRESTO III consists
of applying a sequence of 50µs program pulses to each word until a correct verify occurs
(see Figure 3). During programing and verify operation a MARGIN MODE circuit must be
activated to guarantee that each cell is programed with enough margin. No overprogram
pulse is applied since the verify in MARGIN MODE provides the necessary margin to each
programmed cell.
8/23
M27V322
Device operation
Figure 3.
Programming flowchart
VCC = 6.25V, VPP = 12V
SET MARGIN MODE
n=0
E = 50µs Pulse
NO
NO
++n
= 25
YES
VERIFY
++ Addr
YES
Last
Addr
FAIL
NO
YES
RESET MARGIN MODE
CHECK ALL WORDS
1st: VCC = 5V
2nd: VCC = 3V
AI03059B
2.7
Program Inhibit
Programming of multiple M27V322s in parallel with different data is also easily
accomplished. Except for E, all like inputs including GVPP of the parallel M27V322 may be
common. A TTL low level pulse applied to a M27V322's E input and VPP at 12V, will program
that M27V322. A high level E input inhibits the other M27V322s from being programmed.
2.8
Program Verify
A verify (read) should be performed on the programmed bits to determine that they were
correctly programmed. The verify is accomplished with GVPP at VIL. Data should be verified
with tELQV after the falling edge of E.
2.9
On-Board programming
The M27V322 can be directly programmed in the application circuit. See the relevant
Application Note AN620.
9/23
Device operation
2.10
M27V322
Electronic Signature
The Electronic Signature (ES) mode allows the reading out of a binary code from an
EPROM that will identify its manufacturer and type. This mode is intended for use by
programming equipment to automatically match the device to be programmed with its
corresponding programming algorithm. The ES mode is functional in the 25°C ± 5°C
ambient temperature range that is required when programming the M27V322. To activate
the ES mode, the programming equipment must force 11.5V to 12.5V on address line A9 of
the M27V322, with VPP = VCC = 5V. Two identifier bytes may then be sequenced from the
device outputs by toggling address line A0 from VIL to VIH. All other address lines must be
held at VIL during Electronic Signature mode.
Byte 0 (A0 = VIL) represents the manufacturer code and byte 1 (A0 = VIH) the device
identifier code. For the STMicroelectronics M27V322, these two identifier bytes are given in
Table 3 and can be read-out on outputs Q0 to Q7.
2.11
Erasure operation (applies to UV EPROM)
The erasure characteristics of the M27V322 is such that erasure begins when the cells are
exposed to light with wavelengths shorter than approximately 4000 Å. It should be noted
that sunlight and some type of fluorescent lamps have wavelengths in the 3000-4000 Å
range. Research shows that constant exposure to room level fluorescent lighting could
erase a typical M27V322 in about 3 years, while it would take approximately 1 week to
cause erasure when exposed to direct sunlight. If the M27V322 is to be exposed to these
types of lighting conditions for extended periods of time, it is suggested that opaque labels
be put over the M27V322 window to prevent unintentional erasure. The recommended
erasure procedure for M27V322 is exposure to short wave ultraviolet light which has a
wavelength of 2537 Å. The integrated dose (i.e. UV intensity x exposure time) for erasure
should be a minimum of 30 W-sec/cm2. The erasure time with this dosage is approximately
30 to 40 minutes using an ultraviolet lamp with 12000 µW/cm2 power rating. The M27V322
should be placed within 2.5cm (1 inch) of the lamp tubes during the erasure. Some lamps
have a filter on their tubes which should be removed before erasure.
Operating modes(1)
Table 2.
Mode
E
GVPP
A9
Q15-Q0
Read
VIL
VIL
X
Data Out
Output Disable
VIL
VIH
X
Hi-Z
VIL Pulse
VPP
X
Data In
Program Inhibit
VIH
VPP
X
Hi-Z
Standby
VIH
X
X
Hi-Z
Electronic Signature
VIL
VIL
VID
Codes
Program
1. X = VIH or VIL, VID = 12V ± 0.5V.
Table 3.
Electronic signature(1)
Identifier
A0
Q7
Q6
Q5
Q4
Q3
Q2
Q1
Q0
Hex Data
Manufacturer’s Code
VIL
0
0
1
0
0
0
0
0
20h
Device Code
VIH
0
0
1
1
0
1
0
0
34h
1. Outputs Q15-Q8 are set to '0'.
10/23
M27V322
3
Maximum rating
Maximum rating
Stressing the device above the rating listed in the Absolute Maximum Ratings table may
cause permanent damage to the device. These are stress ratings only and operation of the
device at these or any other conditions above those indicated in the Operating sections of
this specification is not implied. Exposure to Absolute Maximum Rating conditions for
extended periods may affect device reliability. Refer also to the STMicroelectronics SURE
Program and other relevant quality documents.
Table 4.
Absolute maximum ratings
Symbol
TA
Parameter
Ambient Operating
Temperature(1)
Value
Unit
–40 to 125
°C
TBIAS
Temperature Under Bias
–50 to 125
°C
TSTG
Storage Temperature
–65 to 150
°C
Input or Output Voltage (except A9)
–2 to 7
V
Supply Voltage
–2 to 7
V
–2 to 13.5
V
–2 to 14
V
VIO
(2)
VCC
VA9(2)
VPP
A9 Voltage
Program Supply Voltage
1. Depends on range.
2. Minimum DC voltage on Input or Output is –0.5V with possible undershoot to –2.0V for a period less than
20ns. Maximum DC voltage on Output is VCC +0.5V with possible overshoot to VCC +2V for a period less
than 20ns.
11/23
DC and AC parameters
4
M27V322
DC and AC parameters
This section summarizes the operating and measurement conditions, and the DC and AC
characteristics of the device. The parameters in the DC and AC Characteristic tables that
follow are derived from tests performed under the Measurement Conditions summarized in
the relevant tables. Designers should check that the operating conditions in their circuit
match the measurement conditions when relying on the quoted parameters.
Table 5.
AC measurement conditions
High Speed
Standard
Input Rise and Fall Times
≤10ns
≤20ns
Input Pulse Voltages
0 to 3V
0.4V to 2.4V
1.5V
0.8V and 2V
Input and Output Timing Ref. Voltages
Figure 4.
AC testing input output waveform
High Speed
3V
1.5V
0V
Standard
2.4V
0.4V
2.0V
0.8V
AI01822
12/23
M27V322
DC and AC parameters
Figure 5.
AC testing load circuit
1.3V
1N914
3.3kΩ
DEVICE
UNDER
TEST
OUT
CL
CL = 30pF for High Speed
CL = 100pF for Standard
CL includes JIG capacitance
Table 6.
Symbol
CIN
COUT
AI01823B
Capacitance(1) (2)
Parameter
Input Capacitance
Output Capacitance
Test Condition
Min
Max
Unit
VIN = 0V
10
pF
VOUT = 0V
12
pF
1. TA = 25 °C, f = 1 MHz
2. Sampled only, not 100% tested.
13/23
DC and AC parameters
Table 7.
M27V322
Read mode DC characteristics(1) (2)
Symbol
Parameter
Test Condition
Min
Max
Unit
0V ≤VIN ≤VCC
±1
µA
0V ≤VOUT ≤VCC
±10
µA
E = VIL, GVPP = VIL,
IOUT = 0mA, f = 5MHz
30
mA
ILI
Input Leakage Current
ILO
Output Leakage Current
ICC
Supply Current
ICC1
Supply Current (Standby)
TTL
E = VIH
1
mA
ICC2
Supply Current (Standby)
CMOS
E > VCC – 0.2V
60
µA
IPP
Program Current
VPP = VCC
10
µA
VIL
Input Low Voltage
–0.6
0.2VCC
V
VIH(3)
Input High Voltage
0.7VCC
VCC + 0.5
V
VOL
Output Low Voltage
0.4
V
VOH
Output High Voltage TTL
IOL = 2.1mA
IOH = –400µA
2.4
V
1. TA = –40 to 85 °C or 0 to 70 °C; VCC = 3.3V ± 10%; VPP = VCC
2. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP.
3. Maximum DC voltage on Output is VCC +0.5V.
Table 8.
Symbol
Programming mode DC characteristics(1) (2)
Parameter
Test Condition
Min
VIL ≤VIN ≤VIH
Max
Unit
±10
µA
50
mA
50
mA
ILI
Input Leakage Current
ICC
Supply Current
IPP
Program Current
VIL
Input Low Voltage
–0.3
0.8
V
VIH
Input High Voltage
2.4
VCC + 0.5
V
VOL
Output Low Voltage
0.4
V
VOH
Output High Voltage TTL
VID
A9 Voltage
E = VIL
IOL = 2.1mA
IOH = –2.5mA
3.5
11.5
V
12.5
1. TA = 25 °C; VCC = 6.25V ± 0.25V; VPP = 12V ± 0.25V
2. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP.
14/23
V
M27V322
DC and AC parameters
Figure 6.
Read mode AC waveforms
VALID
A0-A20
VALID
tAVQV
tAXQX
E
tEHQZ
tGLQV
GVPP
tGHQZ
tELQV
Hi-Z
Q0-Q15
AI02207
Table 9.
Read mode AC characteristics(1) (2)
M27V322
Symbol
Alt
Parameter
Test
Condition
-100(3)
-120
-150
Unit
Min Max Min Max Min Max
tAVQV
tACC
Address Valid to Output
Valid
E = VIL,
G = VIL
100
120
150
ns
tELQV
tCE
Chip Enable Low to Output
Valid
G = VIL
100
120
150
ns
tGLQV
tOE
Output Enable Low to
Output Valid
E = VIL
50
60
60
ns
tEHQZ(4)
tDF
Chip Enable High to Output
Hi-Z
G = VIL
0
45
0
50
0
50
ns
tGHQZ(4)
tDF
Output Enable High to
Output Hi-Z
E = VIL
0
45
0
50
0
50
ns
tAXQX
tOH
Address Transition to
Output Transition
E = VIL,
G = VIL
5
5
5
ns
1. TA = –40 to 85 °C or 0 to 70 °C; VCC = 3.3V ± 10%; VPP = VCC
2. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP
3. Speed obtained with High Speed measurement conditions.
4. Sampled only, not 100% tested.
15/23
DC and AC parameters
Figure 7.
M27V322
Margin mode AC waveforms
VCC
A8
A9
tA9HVPH
tVPXA9X
GVPP
tVPHEL
tEXVPX
E
tEXA10X
tA10HEH
A10 Set
A10 Reset
tA10LEH
AI00736B
1. A8 High level = 5V; A9 High level = 12V.
Table 10.
Margin mode AC characteristics(1) (2)
Parameter
Test
Condition
Symbol
Alt
tA9HVPH
tAS9
VA9 High to VPP High
2
µs
tVPHEL
tVPS
VPP High to Chip Enable Low
2
µs
tA10HEH
tAS10 VA10 High to Chip Enable High (Set)
1
µs
tA10LEH
tAS10 VA10 Low to Chip Enable High (Reset)
1
µs
tEXA10X
tAH10 Chip Enable Transition to VA10 Transition
1
µs
tEXVPX
tVPH
Chip Enable Transition to VPP Transition
2
µs
tVPXA9X
tAH9
VPP Transition to VA9 Transition
2
µs
Min
Max
1. TA = 25 °C; VCC = 6.25V ± 0.25V; VPP = 12V ± 0.25V
2. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP.
16/23
Unit
M27V322
DC and AC parameters
Figure 8.
Programming and Verify modes AC waveforms
VALID
A0-A20
tAVEL
Q0-Q15
tEHAX
DATA IN
DATA OUT
tQVEL
tEHQX
tEHQZ
VCC
tVCHEL
tEHVPX
tELQV
GVPP
tVPHEL
tVPLEL
E
tELEH
PROGRAM
VERIFY
AI02205
1. BYTE = VIH.
Table 11.
Programming mode AC characteristics(1) (2)
Parameter
Test
Condition
Symbol
Alt
Min
Max
tAVEL
tAS
Address Valid to Chip Enable Low
1
µs
tQVEL
tDS
Input Valid to Chip Enable Low
1
µs
tVCHEL
tVCS
VCC High to Chip Enable Low
2
µs
tVPHEL
tOES
VPP High to Chip Enable Low
1
µs
tVPLVPH
tPRT
VPP Rise Time
50
ns
tELEH
tPW
Chip Enable Program Pulse Width
(Initial)
45
tEHQX
tDH
Chip Enable High to Input Transition
2
µs
tEHVPX
tOEH
Chip Enable High to VPP Transition
2
µs
tVPLEL
tVR
VPP Low to Chip Enable Low
1
µs
tELQV
tDV
Chip Enable Low to Output Valid
tEHQZ(3)
tDFP
Chip Enable High to Output Hi-Z
0
tEHAX
tAH
Chip Enable High to Address Transition
0
55
Unit
µs
1
µs
130
ns
ns
1. TA = 25 °C; VCC = 6.25V ± 0.25V; VPP = 12V ± 0.25V
2. VCC must be applied simultaneously with or before VPP and removed simultaneously or after VPP.
3. Sampled only, not 100% tested.
17/23
Package mechanical
5
M27V322
Package mechanical
Figure 9.
FDIP42W - 42 pin Ceramic Frit-seal DIP, with window (0.315" × 0.630"),
package outline
A2
A3
A
A1
B1
B
L
α
e1
eA
D2
C
eB
D
S
N
K
E1
E
K1
1
FDIPW-b
1. Drawing is not to scale.
Table 12.
FDIP42W - 42 pin Ceramic Frit-seal DIP, with window (0.315" × 0.630"),
mechanical data
millimeters
inches
Symbol
Typ
Min
Max
A1
Min
Max
0.51
1.40
0.020
0.055
A2
3.91
4.57
0.154
0.180
A3
3.89
4.50
0.153
0.177
B
0.41
0.56
0.016
0.022
–
–
–
–
C
0.23
0.30
0.009
0.012
D
54.41
54.86
2.142
2.160
A
B1
5.72
1.45
0.225
0.057
D2
50.80
–
–
2.000
–
–
E
15.24
–
–
0.600
–
–
14.50
14.90
0.571
0.587
E1
18/23
Typ
e
2.54
–
–
0.100
–
–
eA
14.99
–
–
0.590
–
–
eB
16.18
18.03
0.637
0.710
L
3.18
4.10
0.125
0.161
S
1.52
2.49
0.060
0.098
K
8.00
–
–
0.315
–
–
K1
16.00
–
–
0.630
–
–
α
4°
11°
4°
11°
N
42
42
M27V322
Package mechanical
Figure 10. PDIP42 - 42 pin Plastic DIP, 600 mils width, package outline
A2
A1
B1
B
A
L
α
e1
eA
D2
C
eB
D
S
N
E1
E
1
PDIP
1. Drawing is not to scale.
Table 13.
PDIP42 - 42 pin Plastic DIP, 600 mils width, package mechanical data
millimeters
inches
Symbol
Typ
Min
Max
A
–
A1
Typ
Min
Max
5.08
–
0.200
0.25
–
0.010
–
A2
3.56
4.06
0.140
0.160
B
0.38
0.53
0.015
0.021
B1
1.27
1.65
0.050
0.065
C
0.20
0.36
0.008
0.014
D
52.20
52.71
2.055
2.075
D2
50.80
–
–
2.000
–
–
E
15.24
–
–
0.600
–
–
13.59
13.84
0.535
0.545
E1
e1
2.54
–
–
0.100
–
–
eA
14.99
–
–
0.590
–
–
eB
15.24
17.78
0.600
0.700
L
3.18
3.43
0.125
0.135
S
0.86
1.37
0.034
0.054
α
0°
10°
0°
10°
N
42
42
19/23
Package mechanical
M27V322
Figure 11. SDIP42 - 42 pin Shrink Plastic DIP, 600 mils width, package outline
A2
A1
b2
b
A
L
e
eA
D2
c
eB
D
S
N
E1
E
1
SDIP
1. Drawing is not to scale.
Table 14.
SDIP42 - 42 lead Shrink Plastic DIP, 600 mils width, package mechanical
data
millimeters
inches
Symbol
Typ
Min
A
Typ
Min
5.08
A1
Max
0.200
0.51
0.020
A2
3.81
3.05
4.57
0.150
0.120
0.180
b
0.46
0.38
0.56
0.018
0.015
0.022
b2
1.02
0.89
1.14
0.040
0.035
0.045
c
0.25
0.23
0.38
0.010
0.009
0.015
D
36.83
36.58
37.08
1.450
1.440
1.460
D2
35.60
–
–
1.402
–
–
e
1.78
–
–
0.070
–
–
15.24
16.00
0.600
0.630
12.70
14.48
0.500
0.570
E
E1
13.72
eA
15.24
18.54
L
3.30
S
0.64
N
0.540
0.600
eB
20/23
Max
2.54
3.56
0.730
0.130
0.100
0.025
42
42
0.140
M27V322
6
Part numbering
Part numbering
Table 15.
Ordering information scheme
Example:
M27V322
-100 X
F
1
Device Type
M27
Supply Voltage
V = 3.3V ±10%
Device Function
322 = 32 Mbit (2Mb x16)
Speed
-100 = 100 ns(1)
-120 = 120 ns
-150 = 150 ns
VCC Tolerance
blank = 3.3V ±10%
X = 3.3V ±5%
Package
F = FDIP42W
B = PDIP42
S = SDIP42
Temperature Range
1 = 0 to 70 °C
6 = –40 to 85 °C
1. High Speed, see AC Characteristics section for further information.
For a list of available options (Speed, Package, etc.) or for further information on any aspect
of this device, please contact the STMicroelectronics Sales Office nearest to you.
21/23
Revision history
7
Revision history
Table 16.
Document revision history
Date
Revision
July 1999
0.1
02/09/00
1
Programming Flowchart changed (Figure 3)
PRESTO III Programming Algorithm paragraph changed
FDIP42W Package Dimension, L Max added (Table 12)
03/01/01
2
SDIP42 Package added (Figure 11, Table 14)
3
Document converted to new template (sections added, information
moved).
Packages are ECOPACK® compliant. SDIP42 package specifications
updated (see Table 14 and Figure 11).
22-May-2006
22/23
M27V322
Revision Details
First Issue
M27V322
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZE REPRESENTATIVE OF ST, ST PRODUCTS ARE NOT DESIGNED,
AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS,
NOR IN PRODUCTS OR SYSTEMS, WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR
SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2006 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
23/23
Similar pages