FST16210 20-Bit Bus Switch November 1998 Revised June 2005 FST16210 20-Bit Bus Switch General Description Features The Fairchild Switch FST16210 provides 20-Bits of highspeed CMOS TTL-compatible bus switching. The low on resistance of the switch allows inputs to be connected to outputs without adding propagation delay or generating additional ground bounce noise. ■ 4: switch connection between two ports. The device is organized as a 10-bit or 20-Bit bus switch. When OE1 is LOW, the switch is ON and Port 1A is connected to Port 1B. When OE2 is LOW, Port 2A is connected to Port 2B. ■ Control inputs compatible with TTL level. ■ Minimal propagation delay through the switch. ■ Low lCC. ■ Zero bounce in flow-through mode. Ordering Code: Order Number Package Number Package Description MTD48 48-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 6.1mm Wide FST16210MTD Devices also available in Tape and Reel. Specify by appending the suffix letter “X” to the ordering code. Connection Diagram Logic Diagram Truth Table Pin Descriptions Inputs Inputs/Outputs Description OE1 OE2 OE1, OE2 Bus Switch Enables L 1A, 2A Bus A L 1B, 2B Bus B H L Z H H Z Pin Name © 2005 Fairchild Semiconductor Corporation DS500193 1A, 1B 2A, 2B L 1A 1B 2A H 1A 1B 2B Z 2B 2A Z www.fairchildsemi.com FST16210 Absolute Maximum Ratings(Note 1) Supply Voltage (VCC) DC Switch Voltage (VS) DC Input Voltage (VIN ) (Note 2) DC Input Diode Current (lIK) VIN 0V 0.5V to 7.0V 0.5V to 7.0V 0.5V to 7.0V 50mA DC Output (IOUT ) Sink Current DC VCC/GND Current (ICC/IGND) Storage Temperature Range (TSTG) Recommended Operating Conditions (Note 3) 4.0V to 5.5V Power Supply Operating (VCC) 128mA Input Voltage (VIN) 0V to 5.5V Output Voltage (VOUT) 0V to 5.5V Input Rise and Fall Time (tr, tf) / 100mA 65qC to 150 qC Switch Control Input 0nS/V to 5nS/V Switch I/O 0nS/V to DC -40 qC to 85 qC Free Air Operating Temperature (TA) Note 1: The “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. The device should not be operated at these limits. The parametric values defined in the Electrical Characteristics tables are not guaranteed at the absolute maximum rating. The “Recommended Operating Conditions” table will define the conditions for actual device operation. Note 2: The input and output negative voltage ratings may be exceeded if the input and output diode current ratings are observed. Note 3: Unused control inputs must be held high or low. They may not float. DC Electrical Characteristics Symbol VCC (V) Parameter 40 qC to 85 qC TA Min Typ (Note 4) Max 1.2 Clamp Diode Voltage HIGH Level Input Voltage 4.0–5.5 VIL LOW Level Input Voltage 4.0–5.5 0.8 V II Input Leakage Current 5.5 r1.0 PA 0d VIN d5.5V 0 10 PA VIN 5.5 r1.0 PA 0 dA, B dVCC RON OFF-STATE Leakage Current IIN 18mA VIK 2.0 V Conditions VIH IOZ 4.5 Units V 5.5V Switch On Resistance 4.5 4 7 : VIN 0V, IIN 64mA (Note 5) 4.5 4 7 : VIN 0V, IIN 30mA 4.5 8 12 : VIN 2.4V, IIN 15mA 4.0 11 20 : VIN 2.4V, IIN 15mA VCC or GND, IOUT ICC Quiescent Supply Current 5.5 3 PA VIN ' ICC Increase in ICC per Input 5.5 2.5 mA One input at 3.4V 0 Other inputs at VCC or GND Note 4: Typical values are at VCC 5.0V and T A 25qC Note 5: Measured by the voltage drop between A and B pins at the indicated current through the switch. On Resistance is determined by the lower of the voltages on the two (A or B) pins. www.fairchildsemi.com 2 TA Symbol Parameter tPHL,tPLH Propagation Delay Bus to Bus (Note 6) tPZH, tPZL Output Enable Time tPHZ, tPLZ CL Output Disable Time 40 qC to 85 qC, 50pF, RU VCC 4.5 – 5.5V Min Max 1.5 1.5 RD 500: VCC Min Units Conditions 4.0V Figure No. Max 0.25 0.25 ns VI OPEN Figures 1, 2 6.0 6.5 ns VI 7V for tPZL VI OPEN for tPZH Figures 1, 2 VI 7V for tPLZ VI OPEN for tPHZ 7.0 7.2 ns Figures 1, 2 Note 6: This parameter is guaranteed by design but is not tested. The bus switch contributes no propagation delay other than the RC delay of the typical On Resistance of the switch and the 50pF load capacitance, when driven by an ideal voltage source (zero output impedance). Capacitance (Note 7) Symbol CIN CI/O Note 7: TA Parameter Typ Max Units Conditions Control Pin Input Capacitance 3 pF VCC Input/Output Capacitance 6 pF VCC, OE 25qC, f 5.0V 5.0V 1 MHz, Capacitance is characterized but not tested. AC Loading and Waveforms Note: Input driven by 50 : source terminated in 50 : Note: C L includes load and stray capacitance Note: Input PRR 1.0 MHz, tW 500 ns FIGURE 1. AC Test Circuit FIGURE 2. AC Waveforms 3 www.fairchildsemi.com FST16210 AC Electrical Characteristics FST16210 20-Bit Bus Switch Physical Dimensions inches (millimeters) unless otherwise noted 48-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 6.1mm Wide Package Number MTD48 Technology Description The Fairchild Switch family derives from and embodies Fairchild’s proven switch technology used for several years in its 74LVX3L384(FST3384) bus switch product. Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and Fairchild reserves the right at any time without notice to change said circuitry and specifications. LIFE SUPPORT POLICY FAIRCHILD’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD SEMICONDUCTOR CORPORATION. As used herein: 2. A critical component in any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and (c) whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. www.fairchildsemi.com www.fairchildsemi.com 4