LT1313 Dual PCMCIA VPP Driver/Regulator U DESCRIPTION FEATURES ■ ■ ■ ■ ■ ■ ■ ■ ■ ■ Digital Selection of 0V, VCC, 12V or Hi-Z Output Current Capability: 120mA Internal Current Limiting and Thermal Shutdown Automatic Switching from 3.3V to 5V Powered from Unregulated 13V to 20V Supply Logic Compatible with Standard PCMCIA Controllers Output Capacitors: 1µF Quiescent Current in Hi-Z or 0V Mode: 60µA Independent VPP Valid Status Feedback Signals No VPP Overshoot U APPLICATIONS ■ ■ ■ ■ ■ ■ The LT ® 1313 is a member of Linear Technology Corporation’s PCMCIA driver/regulator family. It provides 0V, 3.3V, 5V, 12V and Hi-Z regulated power to the VPP pins of two PCMCIA card slots from a single unregulated 13V to 20V supply. When used in conjunction with a PC Card Interface Controller, the LT1313 forms a complete minimum component-count interface for palmtop, pen-based and notebook computers. The two VPP output voltages are independently selected by four logic compatible digital inputs which interface directly with industry standard PC Card Interface Controllers. Automatic 3.3V to 5V switching is provided by two independent comparators which continuously monitor each PC card VCC supply voltage and automatically adjust the VPP output to match the associated VCC pin voltage when the VPP = VCC mode is selected. Notebook Computers Palmtop Computers Pen-Based Computers Handi-Terminals Bar-Code Readers Flash Memory Programming Two open-collector VPP VALID outputs are provided to indicate when the VPP outputs are in regulation at 12V. The LT1313 is available in 16-pin SO packaging. , LTC and LT are registered trademarks of Linear Technology Corporation. U TYPICAL APPLICATION Typical PCMCIA Dual Slot VPP Driver 13V TO 20V Linear Technology PCMCIA Product Family 0.1µF VS AEN0 VS AVPPOUT VPP1 + AEN1 DUAL PCMCIA CARD SLOT CONTROLLER AVALID BVPPOUT BEN1 BVALID GND VPP2 PCMCIA CARD SLOT #1 VCC ASENSE + 1µF TANTALUM BSENSE GND DEVICE DESCRIPTION PACKAGE LT1312 SINGLE PCMCIA VPP DRIVER/REGULATOR 8-PIN SO LT1313 DUAL PCMCIA VPP DRIVER/REGULATOR 16-PIN SO* ® LTC 1314 SINGLE PCMCIA SWITCH MATRIX 14-PIN SO VPP1 LTC1315 DUAL PCMCIA SWITCH MATRIX 24-PIN SSOP VPP2 PCMCIA CARD SLOT #2 LTC1470 PROTECTED VCC 5V/3.3V SWITCH MATRIX 8-PIN SO LTC1472 PROTECTED VCC AND VPP SWITCH MATRIX 16-PIN SO* 3.3V/5V LT1313 BEN0 1µF TANTALUM *NARROW BODY VCC 1313 TA01 3.3V/5V 1 LT1313 W U U U W W W ABSOLUTE MAXIMUM RATINGS PACKAGE/ORDER INFORMATION Supply Voltage ........................................................ 22V Digital Input Voltage ........................ 7V to (GND – 0.3V) Sense Input Voltage ......................... 7V to (GND – 0.3V) VALID Output Voltage .................... 15V to (GND – 0.3V) Output Short-Circuit Duration .......................... Indefinite Operating Temperature ................................ 0°C to 70°C Junction Temperature................................ 0°C to 125°C Storage Temperature Range ..................–65°C to 150°C Lead Temperature (Soldering, 10 sec).................. 300°C TOP VIEW GND 1 16 AVPPOUT AEN0 2 15 NC AEN1 3 14 VS AVALID 4 13 ASENSE ORDER PART NUMBER LT1313CS GND 5 12 BVPPOUT BEN0 6 11 NC BEN1 7 10 VS BVALID 8 9 BSENSE S PACKAGE 16-LEAD PLASTIC SO TJMAX = 125°C, θJA = 100°C/ W Consult factory for Industrial and Military grade parts. ELECTRICAL CHARACTERISTICS VS = 13V to 20V, TA = 25°C (Note 1), unless otherwise noted. SYMBOL PARAMETER CONDITIONS MIN TYP MAX UNITS VPPOUT Output Voltage Program to 12V, IOUT ≤ 120mA (Note 2) Program to 5V, IOUT ≤ 30mA (Note 2) Program to 3.3V, IOUT ≤ 30mA (Note 2) Program to 0V, IOUT = – 300µA ● ● ● 11.52 4.75 3.135 12.00 5.00 3.30 0.42 12.48 5.25 3.465 0.60 V V V V ILKG Output Leakage Program to Hi-Z, 0V ≤ VPPOUT ≤ 12V ● – 10 10 µA IS Supply Current Both Channels Programmed to 0V Both Channels Programmed to Hi-Z One Channel Programmed to 12V, No Load (Note 3) One Channel Programmed to 5V, No Load (Note 3) One Channel Programmed to 3.3V, No Load (Note 3) One Channel Programmed to 12V, IOUT = 120mA (Note 3) One Channel Programmed to 5V, IOUT = 30mA (Note 3) One Channel Programmed to 3.3V, IOUT = 30mA (Note 3) ● ● ● ● ● ● ● ● 60 60 260 105 85 126 31 31 100 100 400 150 120 132 33 33 µA µA µA µA µA mA mA mA ILIM Current Limit Program to 3.3V, 5V or 12V (Note 3) 330 500 mA VENH Enable Input High Voltage ● VENL Enable Input Low Voltage ● IENH Enable Input High Current 2.4V ≤ VIN ≤ 5.5V IENL Enable Input Low Current 0V ≤ VIN ≤ 0.4V VSEN5 VCC Sense Threshold VPPOUT = 3.3V to 5V (Note 4) ● VSEN3 VCC Sense Threshold VPPOUT = 5V to 3.3V (Note 4) ● ISEN VCC Sense Input Current VSENSE = 5V VSENSE = 3.3V VVALID TH VPPVALID Threshold Voltage Program to 12V, (Note 5) IVALID VPPVALIDOutput Drive Current Program to 12V, VVALID = 0.4V, (Note 5) VPPVALID Output Leakage Current Program to 0V, VVALID = 12V, (Note 5) The ● denotes the specifications which apply over the full operating temperature range. Note 1: Both VS pins (10, 14) must be connected together, and both ground pins (1, 5) must be connected together. Note 2: For junction temperatures greater than 110°C, a minimum load of 1mA is recommended. 2 ● 2.4 V 0.4 V 20 50 µA 0.01 1 µA 3.60 4.05 4.50 V 3.60 4.00 4.50 V 38 18 60 30 µA µA 10.5 11 11.5 1 3.3 0.1 V mA 10 µA Note 3: The other channel is programmed to the 0V mode (XEN0 = XEN1 = 0V) during this test. Note 4: The VCC sense threshold voltage tests are performed independently. Note 5: The VPPVALID tests are performed independently. LT1313 U W TYPICAL PERFORMANCE CHARACTERISTICS Quiescent Current (0V or Hi-Z Mode) Quiescent Current (12V Mode) 60 40 20 5 0 15 20 10 SUPPLY VOLTAGE (V) 400 300 200 100 0 25 TJ = 25°C ONE CHANNEL PROGRAMMED TO 12V OTHER CHANNEL IN 0V OR Hi-Z MODE RL = ∞ 5 15 20 10 SUPPLY VOLTAGE (V) Ground Pin Current (12V Mode) 2 RL = 400Ω IL = 30mA* 5 0 15 20 10 SUPPLY VOLTAGE (V) 2.0 1.5 RL = 167Ω IL = 30mA* 1.0 RL = 500Ω IL = 10mA* 25 0 5 SHORT-CIRCUIT CURRENT (mA) GROUND PIN CURRENT (mA) 12 10 8 6 4 1.0 40 60 80 100 120 140 160 OUTPUT CURRENT (mA) 1313 G07 RL = 330Ω IL = 10mA* 15 20 10 SUPPLY VOLTAGE (V) *FOR VPPOUT = 3.3V 25 0 5 15 20 10 SUPPLY VOLTAGE (V) Current Limit TJ = 25°C XVPPOUT = 0V SINGLE CHANNEL 600 500 400 300 200 0 5 25 1313 G06 600 700 0 20 RL = 110Ω IL = 30mA* 0 100 2 0 1.5 Current Limit 800 TJ = 25°C VS = 15V SINGLE CHANNEL 14 2.0 1313 G05 Ground Pin Current 25 TJ = 25°C 3.3V MODE SINGLE OUTPUT VSENSE = 3.3V 0.5 *FOR VPPOUT = 5V 0 1313 G04 16 15 20 10 SUPPLY VOLTAGE (V) Ground Pin Current (3.3V Mode) TJ = 25°C 5V MODE SINGLE OUTPUT VSENSE = 5V 0.5 *FOR VPPOUT = 12V 0 5 2.5 SHORT-CIRCUIT CURRENT (mA) RL = 200Ω IL = 60mA* 0 1313 G03 GROUND CURRENT (mA) GROUND CURRENT (mA) GROUND CURRENT (mA) TJ = 25°C 12V MODE SINGLE OUTPUT 4 VSENSE = 3.3V 50 Ground Pin Current (5V Mode) RL = 100Ω IL = 120mA* VSENSE = 5V 100 25 2.5 6 150 1313 G02 10 8 TJ = 25°C ONE CHANNEL PROGRAMMED TO VPP = VCC. OTHER CHANNEL IN 0V OR Hi-Z MODE RL = ∞ 200 0 0 LT1313 G1 0 QUIESCENT CURRENT (µA) TJ = 25°C BOTH CHANNELS PROGRAMMED TO 0V OR BOTH CHANNELS PROGRAMMED TO Hi-Z 80 0 Quiescent Current (3.3V/5V Mode) 250 500 QUIESCENT CURRENT (µA) QUIESCENT CURRENT (µA) 100 10 15 INPUT VOLTAGE (V) 20 25 1313 G08 VS = 15V XVPPOUT = 0V SINGLE CHANNEL 500 400 300 200 100 0 0 25 50 75 100 JUNCTION TEMPERATURE (°C) 125 1313 G09 3 LT1313 U W TYPICAL PERFORMANCE CHARACTERISTICS Enable Input Threshold Voltage 5.5 2.0 1.5 1.0 0.5 VCC SENSE THRESHOLD VOLTAGES (V) 2.5 TJ = 25°C VS = 15V ENABLE INPUT CURRENT (µA) INPUT THRESHOLD VOLTAGE (V) VS = 15V 0 VCC Sense Threshold Voltage Enable Input Current 50 3.0 40 30 20 10 0 0 0 125 25 50 75 100 JUNCTION TEMPERATURE (°C) 1 2 3 4 5 ENABLE INPUT VOLTAGE (V) VCC Sense Input Current 30 20 10 5 2 3 4 1 VCC SENSE INPUT VOLTAGE (V) TJ = 25°C VS = 15V 12V MODE 0.8 0.6 0.4 0.2 2.5 1.0 1.5 2.0 0.5 VALID OUTPUT CURRENT (mA) 0 0.4 0.6 TIME (ms) 0.8 1.0 1.2 1313 G16 4 40 20 100 1k 10k FREQUENCY (Hz) COUT = 1µF 0 COUT = 10µF –20 0.4 0.2 COUT = 1µF 0 COUT = 10µF –0.2 –0.4 15 13 –0.1 1M Load Transient Response (12V) 40 20 100k 1313 G15 LOAD CURRENT (mA) SUPPLY VOLTAGE (V) 5 COUT = 1µF TANTALUM 10 –40 0.2 60 3.0 OUTPUT VOLTAGE CHANGE (V) OUTPUT VOLTAGE CHANGE (mV) COUT = 10µF 11.6 EN0 INPUT (V) OUTPUT VOLTAGE (V) 12.0 0 80 Line Transient Response (12V) VS = 15V –0.2 TJ = 25°C, 12V MODE VS = 15V + 100mVRMS RIPPLE 1313 G14 1313 G13 12V Turn-On Waveform 125 25 50 75 100 JUNCTION TEMPERATURE (°C) 0 0 6 12.4 0 Ripple Rejection (12V) 0 0 COUT = 1µF 3.0 100 RIPPLE REJECTION RATIO (dB) VALID OUTPUT VOLTAGE (V) VCC SENSE INPUT CURRENT (µA) 40 SWITCH TO 3.3V 3.5 VALID Output Voltage TJ = 25°C VS = 15V 11.8 SWITCH TO 5V 4.0 1313 G12 1.0 50 12.2 4.5 1313 G11 1313 G10 0 5.0 2.5 6 TJ = 25°C VS = 15V 0 0.1 0.2 0.3 TIME (ms) 0.4 0.5 0.6 1313 G17 100 50 –0.1 0 0.1 0.2 0.3 TIME (ms) 0.4 0.5 0.6 1313 G18 LT1313 U U U PIN FUNCTIONS Supply Pins: Power is supplied to the device through the two supply pins which must be connected together at all times . The supply pins should be bypassed to ground if the device is more than six inches away from the main supply capacitor. A bypass capacitor in the range of 0.1µF to 1µF is sufficient. The supply voltage to the LT1313 can be loosely regulated between 13V and 20V. VPPOUT Pins: Each regulated output supplies power to the two PCMCIA card VPP pins which are typically tied together at the socket. Each VPPOUT output is current limited to approximately 330mA. Thermal shutdown provides a second level of protection. A 1µF to 10µF tantalum output capacitor is recommended. Input Enable Pins: The four digital input pins are high impedance inputs with approximately 20µA input current at 2.4V. The input thresholds are compatible with CMOS controllers and can be driven from either 5V or 3.3V CMOS logic. ESD protection diodes limit input excursions to 0.6V below ground. W BLOCK DIAGRAM VCC Sense Pins: Two independent comparators and 4V references automatically switch the VPPOUT outputs from 5V to 3.3V depending upon the voltage sensed at the corresponding PCMCIA card socket VCC pin. The input current for these pins is approximately 30µA. For 5V only operation, connect the Sense pins directly to ground. An ESD protection diode limits the input voltage to 0.6V below ground. Ground Pins: The two ground pins must be connected together at all times. (One Channel) LOW DROPOUT LINEAR REGULATOR VS XVCC SENSE VALID Output Pins: These pins are open-collector NPN outputs which are driven low when the corresponding VPPOUT pin is in regulation, i.e., when it is above 11V. Two external 51k pull-up resistors are connected between these outputs and the same 5V or 3.3V logic supply powering the PCMCIA compatible control logic. XVPPOUT + – 4V XVALID + XEN0 VOLTAGE LOGIC CONTROL – XEN1 11V X = A OR B 1313 BD 5 LT1313 U OPERATION The LT1313 is two programmable output voltage, lowdropout linear regulators designed specifically for PCMCIA VPP drive applications. Input power is typically obtained from a loosely regulated input supply between 13V and 20V. The LT1313 consists of the following blocks: Two Low Dropout Voltage Linear Regulators: The heart of the LT1313 is two PNP-based low-dropout voltage regulators which drop the unregulated supply voltage from 13V to 20V down to 12V, 5V, 3.3V, 0V or Hi-Z depending upon the state of the four Enable inputs and the two VCC Sense inputs. The regulators have built-in current limiting and thermal shutdown to protect the device, the loads, and the sockets against inadvertent short circuiting to ground. Voltage Control Logic: The two VPPOUT outputs have five possible output modes: 0V, 3.3V, 5V, 12V and Hi-Z. These five modes are selected by the four Enable inputs and the two VCC Sense inputs as described by the Truth Table. VCC Sense Comparators: When the VCC mode is selected, the LT1313 automatically adjusts each regulated VPP output voltage to 3.3V or 5V depending upon the voltage present at the corresponding PC card VCC supply pin. The threshold voltage for these comparators is set at 4V and there is approximately 50mV of hysteresis provided to ensure clean switching between 3.3V and 5V. VPP VALID Comparator: Two voltage comparators monitor each output voltage when the 12V mode is selected and are driven low when the output is in regulation above 11V. These two outputs function separately. LT1313 Truth Table AEN0 AEN1 ASENSE AVPPOUT AVALID 0 1 0 0 1 0 0 1 1 1 X X 3.0V to 3.6V 4.5V to 5.5V X 0V 12V 3.3V 5V Hi-Z 1 0 1 1 1 BEN0 BEN1 BSENSE BVPPOUT BVALID 0 1 0 0 1 0 0 1 1 1 X X 3.0V to 3.6V 4.5V to 5.5V X 0V 12V 3.3V 5V Hi-Z 1 0 1 1 1 X = Don’t Care Note: Each channel is independently controlled. U W U U APPLICATIONS INFORMATION The LT1313 is two voltage programmable linear regulators designed specifically for PCMCIA VPP driver applications. The device operates with very low quiescent current (60µA) in the 0V and Hi-Z modes of operation. In the Hi-Z mode, the output leakage current falls to 1µA. In addition to the low quiescent currents, the LT1313 incorporates several protection features which make it ideal for PCMCIA applications. The LT1313 has built-in current limiting (330mA) and thermal shutdown to protect the device and the socket VPP pins against inadvertent short-circuit conditions. Output Capacitance The LT1313 is designed to be stable with a wide range of output capacitors. The minimum recommended value is a 1µF with an ESR of 3Ω or less. The capacitor is connected directly between the output pin and ground. For applications where space is very limited, capacitors as low as 0.33µF can 6 be used. Extremely low ESR ceramic capacitors with values less than 1µF must have a 2Ω resistor added in series with the output capacitor. Transient and Switching Performance The LT1313 is designed to produce minimal overshoot with capacitors in the range of 1µF to 10µF. Larger capacitor values can be used with a slowing of rise and fall times. The positive output slew rate is determined by the 330mA current limit and the output capacitor. The rise time for a 0V to 12V transition is approximately 40µs and the rise time for a 10µF capacitor is roughly 400µs (see the Transient Response curves in the Typical Performance Characteristics section). LT1313 U W U U APPLICATIONS INFORMATION The fall time from 12V to 0V is set by the output capacitor and an internal pull-down current source which sinks about 30mA. This source will fully discharge a 1µF capacitor in less than 1ms. Thermal Considerations Power dissipated by the device is the sum of two components: output current multiplied by the input-output differential voltage: IOUT × (VIN – VOUT), and ground pin current multiplied by supply voltage: (IGND × VIN). The ground pin current can be found by examining the Ground Pin Current curves in the Typical Performance Characteristics section. Heat sinking, for surface mounted devices, is accomplished by using the heat spreading capabilities of the PC board and its copper traces. The junction temperature of the LT1313 must be limited to 125°C to ensure proper operation. Use Table 1, in conjunction with the typical performance graphs, to calculate the power dissipation and die temperature for a particular application and ensure that the die temperature does not exceed 125°C under any operating conditions. Table 1. 16-Pin SO Package* COPPER AREA TOPSIDE 2500 sq mm 1000 sq mm 225 sq mm 1000 sq mm BACKSIDE BOARD AREA THERMAL RESISTANCE (JUNCTION-TO-AMBIENT) 2500 sq mm 2500 sq mm 2500 sq mm 1000 sq mm 2500 sq mm 2500 sq mm 2500 sq mm 1000 sq mm 120°C/W 120°C/W 125°C/W 131°C/W Calculating Junction Temperature Example: given an output voltage of 12V, an input supply voltage of 14V, and an output current of 100mA (one VPP output), and a maximum ambient temperature of 50°C, what will the maximum junction temperature be? Power dissipated by the device will be equal to: IOUT × (VS – VPPOUT) + (IGND × VIN) where, IOUT = 100mA VIN = 14V IGND at (IOUT = 100mA, VIN = 14V) = 5mA so, PD = 100mA × (14V –12V) + (5mA × 15V) = 0.275W Using Table 1, the thermal resistance will be in the range of 120°C/W to 131°C/W depending upon the copper area. So the junction temperature rise above ambient will be less than or equal to: 0.275W × 131°C/W = 36°C The maximum junction temperature will then be equal to the junction temperature rise above ambient plus the maximum ambient temperature or: TJMAX = 50°C + 36°C = 86°C For more detailed applications information, see the LT1312 Single PCMCIA VPP Driver/Regulator data sheet. * Device is mounted on topside. 7 LT1313 U TYPICAL APPLICATIONS Dual Slot PCMCIA Interface to CL-PD6720 VLOGIC 13V TO 20V 0.1µF 51k A_VPP_PGM VS AEN0 A_VPP_VCC AEN1 VPP1 VS AVPPOUT VPP2 + PCMCIA CARD SLOT #1 1µF 3.3V/5V AVALID VCC ASENSE LT1313 B_VPP_PGM BEN0 VPP1 BVPPOUT VPP2 + 1µF B_VPP_VCC BEN1 VPP_VALID BVALID GND 3.3V/5V BSENSE GND CIRRUS LOGIC CL-PD6720 Q1 Si9405DY Q2 Si9933DY AVCC 3V 5V + 10µF Q3 Si9933DY Q4 Si9405DY BVCC 5V 3.3V Q5 Si9933DY BVCC 3V Q6 Si9933DY 3.3V + 10µF P-CHANNEL VCC SWITCHING N-CHANNEL VCC SWITCHING USING LTC1165 INVERTING N-CHANNEL DRIVERS 5V IN1 AVCC 5V VS 5V Q1 1/2 Si9956DY OUT1 TO VCC SLOT 1 LTC1165CS8 AVCC 3V IN3 IN1 VS OUT1 Q2 Si9956DY OUT2 IN2 5V GND Q3 Si9956DY OUT3 5V Q4 1/2 Si9956DY IN2 IN3 GND OUT2 Q5 Si9956DY OUT3 Q6 Si9956DY 3.3V 8 3.3V TO VCC SLOT 2 LTC1165CS8 BVCC 3V VCC 5V AVCC 5V BVCC 5V PCMCIA CARD SLOT #2 1313 TA02 LT1313 U TYPICAL APPLICATIONS Dual Slot PCMCIA Interface to “365” Type Controller VLOGIC 13V TO 20V 51k 51k 0.1µF VS AVPPOUT VS AEN0 A_VPP_EN0 A_VPP_EN1 VPP1 VPP2 PCMCIA CARD SLOT #1 VCC + 1µF AEN1 3.3V/5V AVALID A:GP1 ASENSE LT1313 B_VPP_EN0 BEN0 B_VPP_EN1 BEN1 VPP1 BVPPOUT VPP2 + 1µF 3.3V/5V BVALID GND B:GP1 BSENSE GND PCMCIA CARD SLOT #2 VCC “365” TYPE CONTROLLER 5V VS IN1 A_VCC_EN0 5V Q1 1/2 Si9956DY G1 LTC1157CS8 Q2 Si9956DY A_VCC_EN1 IN2 GND 5V B_VCC_EN1 VS Q3 Si9956DY G1 3.3V Q4 1/2 Si9956DY LTC1157CS8 Q5 Si9956DY IN2 GND 10µF G2 5V B_VCC_EN0 IN1 + + 10µF G2 Q6 Si9956DY 1313 TA03 3.3V 9 LT1313 U TYPICAL APPLICATIONS Dual Slot PCMCIA Driver/Regulator Powered from Auxiliary Winding on 5V Inductor of LTC1142HV Dual 5V/3.3V Switching Regulator VIN 6.5V TO 18V VIN D1 MBRS140 10 + Q1 PDRIVE LTC1148 SINGLE 5V REG 9 R4 22Ω C1 68µF C4 1000pF D2 MBRS140 14V AUXILIARY SUPPLY Q2 NDRIVE SENSE 20 D3 MBRS130T3 R1 100Ω + 15 SENSE– 14 C2 1000pF R3 18k Q3 VN7002 T1* 1.8T 30µH + C5 22µF VS VS AVPPOUT AEN0 R5 0.033Ω R2 100Ω + C3 220µF 5V OUTPUT TO “A” SLOT VPP PINS + 1µF AEN1 AVALID FROM “A” SLOT VCC PIN ASENSE LT1313 Q4 VN7002 BEN0 *LPE-6562-A026 DALE (605) 655-9301 AEN0 AEN1 AVALID BVPPOUT TO “B” SLOT VPP PINS + 1µF BEN1 BVALID BSENSE GND GND FROM “B” SLOT VCC PIN BEN0 BEN1 1313 TA04 BVALID NOTE: SEE LT1312 DATA SHEET APPLICATIONS SECTION FOR FURTHER DETAILS ON THIS CIRCUIT 10 LT1313 U PACKAGE DESCRIPTION Dimensions in inches (millimeters) unless otherwise noted. S Package 16-Lead Narrow Plastic SOIC 0.386 – 0.394* (9.804 – 10.008) 16 15 14 13 12 11 10 9 0.150 – 0.157* (3.810 – 3.988) 0.228 – 0.244 (5.791 – 6.197) 1 0.010 – 0.020 × 45° (0.254 – 0.508) 0.008 – 0.010 (0.203 – 0.254) 2 3 4 5 6 8 0.053 – 0.069 (1.346 – 1.752) 0.004 – 0.010 (0.101 – 0.254) 0° – 8° TYP 0.016 – 0.050 0.406 – 1.270 7 0.014 – 0.019 (0.355 – 0.483) 0.050 (1.270) TYP SO16 0893 *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.006 INCH (0.15mm). Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 11 LT1313 RELATED PARTS See PCMCIA Product Family table on the first page of this data sheet. 12 Linear Technology Corporation LT/GP 0994 10K • PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7487 (408) 432-1900 ● FAX: (408) 434-0507 ● TELEX: 499-3977 LINEAR TECHNOLOGY CORPORATION 1994