MOTOROLA MC68HC908GZ8CFJ

Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MC68HC908GZ8
Data Sheet
M68HC08
Microcontrollers
MC68HC908GZ8/D
Rev. 0
2/2003
MOTOROLA.COM/SEMICONDUCTORS
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MC68HC908GZ8
Freescale Semiconductor, Inc...
Data Sheet
To provide the most up-to-date information, the revision of our documents on the
World Wide Web will be the most current. Your printed copy may be an earlier
revision. To verify you have the latest information available, refer to:
http://motorola.com/semiconductors
The following revision history table summarizes changes contained in this
document. For your convenience, the page number designators have been linked
to the appropriate location.
Motorola and the Stylized M Logo are registered trademarks of Motorola, Inc.
DigitalDNA is a trademark of Motorola, Inc.
This product incorporates SuperFlash® technology licensed from SST.
MC68HC908GZ8
© Motorola, Inc., 2003
Data Sheet
MOTOROLA
3
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Revision History
Revision History
Revision
Level
February,
2003
N/A
Description
Initial release
Page
Number(s)
N/A
Freescale Semiconductor, Inc...
Date
Data Sheet
4
MC68HC908GZ8
Revision History
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
List of Sections
Section 1. General Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .21
Freescale Semiconductor, Inc...
Section 2. Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Section 3. Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Section 4. Resets and Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Section 5. Analog-to-Digital Converter (ADC) . . . . . . . . . . . . . . . . . . . 65
Section 6. Break Module (BRK) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
Section 7. Clock Generator Module (CGM). . . . . . . . . . . . . . . . . . . . . . 83
Section 8. Configuration Register (CONFIG) . . . . . . . . . . . . . . . . . . . 103
Section 9. Computer Operating Properly (COP) Module. . . . . . . . . . 107
Section 10. Central Processor Unit (CPU) . . . . . . . . . . . . . . . . . . . . . 111
Section 11. FLASH Memory (FLASH) . . . . . . . . . . . . . . . . . . . . . . . . . 125
Section 12. External Interrupt (IRQ) . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Section 13. Keyboard Interrupt Module (KBI) . . . . . . . . . . . . . . . . . . 139
Section 14. Low-Voltage Inhibit (LVI) . . . . . . . . . . . . . . . . . . . . . . . . . 145
Section 15. Monitor ROM (MON) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
Section 16. MSCAN08 Controller (MSCAN08) . . . . . . . . . . . . . . . . . . 161
Section 17. Input/Output (I/O) Ports . . . . . . . . . . . . . . . . . . . . . . . . . . 199
Section 18. Random-Access Memory (RAM) . . . . . . . . . . . . . . . . . . . 217
Section 19. Enhanced Serial Communications
Interface (ESCI) Module . . . . . . . . . . . . . . . . . . . . . . . . . 219
Section 20. System Integration Module (SIM) . . . . . . . . . . . . . . . . . . 255
MC68HC908GZ8
MOTOROLA
Data Sheet
List of Sections
For More Information On This Product,
Go to: www.freescale.com
5
Freescale Semiconductor, Inc.
List of Sections
Section 21. Serial Peripheral Interface (SPI) Module. . . . . . . . . . . . . 275
Section 22. Timebase Module (TBM). . . . . . . . . . . . . . . . . . . . . . . . . . 299
Section 23. Timer Interface Module (TIM) . . . . . . . . . . . . . . . . . . . . . . 305
Section 24. Electrical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . 323
Freescale Semiconductor, Inc...
Section 25. Ordering Information
and Mechanical Specifications . . . . . . . . . . . . . . . . . . . 339
Data Sheet
6
MC68HC908GZ8
List of Sections
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Table of Contents
Freescale Semiconductor, Inc...
Section 1. General Description
1.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
1.2
1.2.1
1.2.2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Standard Features of the MC68HC908GZ8 . . . . . . . . . . . . . . . . . . . 21
Features of the CPU08 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
1.3
MCU Block Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
1.4
Pin Assignments . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
1.5
1.5.1
1.5.2
1.5.3
1.5.4
1.5.5
1.5.6
1.5.7
Pin Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Supply Pins (VDD and VSS) . . . . . . . . . . . . . . . . . . . . . . . . . .
Oscillator Pins (OSC1 and OSC2) . . . . . . . . . . . . . . . . . . . . . . . . . .
External Reset Pin (RST) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
External Interrupt Pin (IRQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CGM Power Supply Pins (VDDA and VSSA) . . . . . . . . . . . . . . . . . . .
External Filter Capacitor Pin (VCGMXFC). . . . . . . . . . . . . . . . . . . . . .
ADC Power Supply/Reference Pins
(VDDAD/VREFH and VSSAD/VREFL) . . . . . . . . . . . . . . . . . . . . . . . .
1.5.8
Port A Input/Output (I/O) Pins (PTA7/KBD7–PTA0/KBD0). . . . . . . .
1.5.9
Port B I/O Pins (PTB7/AD7–PTB0/AD0). . . . . . . . . . . . . . . . . . . . . .
1.5.10
Port C I/O Pins (PTC6–PTC0/CANTX). . . . . . . . . . . . . . . . . . . . . . .
1.5.11
Port D I/O Pins (PTD7/T2CH1–PTD0/SS) . . . . . . . . . . . . . . . . . . . .
1.5.12
Port E I/O Pins (PTE5–PTE2, PTE1/RxD, and PTE0/TxD) . . . . . . .
26
26
26
26
27
27
27
27
27
27
28
28
28
Section 2. Memory Map
2.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2.2
Unimplemented Memory Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2.3
Reserved Memory Locations . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2.4
Input/Output (I/O) Section. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Section 3. Low-Power Modes
3.1
3.1.1
3.1.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
3.2
3.2.1
3.2.2
Analog-to-Digital Converter (ADC) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 41
MC68HC908GZ8
MOTOROLA
Data Sheet
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
7
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Table of Contents
3.3
3.3.1
3.3.2
Break Module (BRK). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3.4
3.4.1
3.4.2
Clock Generator Module (CGM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3.5
3.5.1
3.5.2
Computer Operating Properly Module (COP). . . . . . . . . . . . . . . . . . . . . 42
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.6
3.6.1
3.6.2
Central Processor Unit (CPU). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.7
3.7.1
3.7.2
External Interrupt Module (IRQ) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43
3.8
3.8.1
3.8.2
Keyboard Interrupt Module (KBI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
3.9
3.9.1
3.9.2
Low-Voltage Inhibit Module (LVI) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
3.10 Motorola Scalable Controller Area Network Module (MSCAN) . . . . . . . 44
3.10.1
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
3.10.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44
3.11 Enhanced Serial Communications Interface Module (ESCI) . . . . . . . . . 45
3.11.1
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.11.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.12 Serial Peripheral Interface Module (SPI) . . . . . . . . . . . . . . . . . . . . . . . . 45
3.12.1
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.12.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.13 Timebase Module (TBM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.13.1
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 45
3.13.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3.14 Timer Interface Module (TIM1 and TIM2) . . . . . . . . . . . . . . . . . . . . . . . . 46
3.14.1
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3.14.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3.15
Exiting Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
3.16
Exiting Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48
Data Sheet
8
MC68HC908GZ8
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Table of Contents
Section 4. Resets and Interrupts
Freescale Semiconductor, Inc...
4.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49
4.2
Resets . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.1
Effects. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.2
External Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.3
Internal Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.3.1
Power-On Reset (POR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.3.2
Computer Operating Properly (COP) Reset . . . . . . . . . . . . . . . . .
4.2.3.3
Low-Voltage Inhibit (LVI) Reset . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.3.4
Illegal Opcode Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.3.5
Illegal Address Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.2.4
System Integration Module (SIM) Reset Status Register . . . . . . . . .
49
49
49
49
50
50
51
51
51
51
4.3
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.1
Effects. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.2
Sources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.2.1
Software Interrupt (SWI) Instruction . . . . . . . . . . . . . . . . . . . . . . .
4.3.2.2
Break Interrupt . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.2.3
IRQ Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.2.4
Clock Generator (CGM) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.2.5
Timer Interface Module 1 (TIM1). . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.2.6
Timer Interface Module 2 (TIM2). . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.2.7
Serial Peripheral Interface (SPI) . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.2.8
Serial Communications Interface (SCI) . . . . . . . . . . . . . . . . . . . . .
4.3.2.9
KBD0–KBD7 Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.2.10
Analog-to-Digital Converter (ADC) . . . . . . . . . . . . . . . . . . . . . . . .
4.3.2.11
Timebase Module (TBM). . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.2.12
Motorola Scalable Controller Area Network
Module (MSCAN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.3
Interrupt Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.3.1
Interrupt Status Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.3.2
Interrupt Status Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
4.3.3.3
Interrupt Status Register 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
53
53
54
57
57
57
57
57
57
58
58
59
59
59
60
61
62
62
63
Section 5. Analog-to-Digital Converter (ADC)
5.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
5.2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65
5.3
5.3.1
5.3.2
5.3.3
5.3.4
5.3.5
5.3.6
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADC Port I/O Pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Voltage Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conversion Time. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Accuracy and Precision . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Result Justification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.4
Monotonicity . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
MC68HC908GZ8
MOTOROLA
65
65
66
67
67
67
67
Data Sheet
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
9
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Table of Contents
5.5
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
5.6
5.6.1
5.6.2
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69
5.7
5.7.1
5.7.2
5.7.3
5.7.4
5.7.5
I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADC Analog Power Pin (VDDAD). . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADC Analog Ground Pin (VSSAD) . . . . . . . . . . . . . . . . . . . . . . . . . . .
ADC Voltage Reference High Pin (VREFH) . . . . . . . . . . . . . . . . . . . .
ADC Voltage Reference Low Pin (VREFL) . . . . . . . . . . . . . . . . . . . .
ADC Voltage In (VADIN) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
69
69
70
70
70
70
5.8
I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8.1
ADC Status and Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8.2
ADC Data Register High and Data Register Low . . . . . . . . . . . . . . .
5.8.2.1
Left Justified Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8.2.2
Right Justified Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8.2.3
Left Justified Signed Data Mode . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8.2.4
Eight Bit Truncation Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.8.3
ADC Clock Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
71
71
73
73
73
74
74
75
Section 6. Break Module (BRK)
6.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
6.2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77
6.3
6.3.1
6.3.2
6.3.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Flag Protection During Break Interrupts . . . . . . . . . . . . . . . . . . . . . .
TIM During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
COP During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
77
79
79
79
6.4
6.4.1
6.4.2
6.4.3
6.4.4
Break Module Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Break Status and Control Register . . . . . . . . . . . . . . . . . . . . . . . . . .
Break Address Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Break Status Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Break Flag Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
80
80
81
81
82
6.5
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Section 7. Clock Generator Module (CGM)
7.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
7.2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83
7.3
7.3.1
7.3.2
7.3.3
7.3.4
7.3.5
7.3.6
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Crystal Oscillator Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Phase-Locked Loop Circuit (PLL). . . . . . . . . . . . . . . . . . . . . . . . . . .
PLL Circuits . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Acquisition and Tracking Modes. . . . . . . . . . . . . . . . . . . . . . . . . . . .
Manual and Automatic PLL Bandwidth Modes . . . . . . . . . . . . . . . . .
Programming the PLL. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Sheet
10
83
85
85
85
86
86
88
MC68HC908GZ8
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Table of Contents
Freescale Semiconductor, Inc...
7.3.7
7.3.8
7.3.9
Special Programming Exceptions. . . . . . . . . . . . . . . . . . . . . . . . . . . 90
Base Clock Selector Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 90
CGM External Connections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 91
7.4
I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.4.1
Crystal Amplifier Input Pin (OSC1) . . . . . . . . . . . . . . . . . . . . . . . . . .
7.4.2
Crystal Amplifier Output Pin (OSC2) . . . . . . . . . . . . . . . . . . . . . . . .
7.4.3
External Filter Capacitor Pin (CGMXFC) . . . . . . . . . . . . . . . . . . . . .
7.4.4
PLL Analog Power Pin (VDDA) . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.4.5
PLL Analog Ground Pin (VSSA) . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.4.6
Oscillator Enable Signal (SIMOSCEN) . . . . . . . . . . . . . . . . . . . . . . .
7.4.7
Oscillator Stop Mode Enable Bit (OSCSTOPENB). . . . . . . . . . . . . .
7.4.8
Crystal Output Frequency Signal (CGMXCLK). . . . . . . . . . . . . . . . .
7.4.9
CGM Base Clock Output (CGMOUT) . . . . . . . . . . . . . . . . . . . . . . . .
7.4.10
CGM CPU Interrupt (CGMINT). . . . . . . . . . . . . . . . . . . . . . . . . . . . .
92
92
92
92
92
92
92
92
93
93
93
7.5
7.5.1
7.5.2
7.5.3
7.5.4
7.5.5
CGM Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PLL Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
PLL Bandwidth Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . .
PLL Multiplier Select Register High . . . . . . . . . . . . . . . . . . . . . . . . .
PLL Multiplier Select Register Low . . . . . . . . . . . . . . . . . . . . . . . . . .
PLL VCO Range Select Register . . . . . . . . . . . . . . . . . . . . . . . . . . .
93
94
96
97
98
98
7.6
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
7.7
7.7.1
7.7.2
7.7.3
Special Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 99
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
CGM During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 100
7.8
7.8.1
7.8.2
7.8.3
Acquisition/Lock Time Specifications . . . . . . . . . . . . . . . . . . . . . . . . . .
Acquisition/Lock Time Definitions . . . . . . . . . . . . . . . . . . . . . . . . . .
Parametric Influences on Reaction Time . . . . . . . . . . . . . . . . . . . .
Choosing a Filter. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
100
100
101
102
Section 8. Configuration Register (CONFIG)
8.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
8.2
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 103
Section 9. Computer Operating Properly (COP) Module
9.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
9.2
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
9.3
9.3.1
9.3.2
9.3.3
9.3.4
9.3.5
I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
CGMXCLK . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
STOP Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
COPCTL Write . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power-On Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Internal Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
MC68HC908GZ8
MOTOROLA
108
108
108
108
108
109
Data Sheet
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
11
Freescale Semiconductor, Inc.
Table of Contents
Freescale Semiconductor, Inc...
9.3.6
9.3.7
9.3.8
Reset Vector Fetch . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
COPD (COP Disable) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
COPRS (COP Rate Select) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
9.4
COP Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
9.5
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
9.6
Monitor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
9.7
9.7.1
9.7.2
Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
9.8
COP Module During Break Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
Section 10. Central Processor Unit (CPU)
10.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
10.2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 111
10.3 CPU Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.3.1
Accumulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.3.2
Index Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.3.3
Stack Pointer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.3.4
Program Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.3.5
Condition Code Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
10.4
112
112
113
113
114
114
Arithmetic/Logic Unit (ALU) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
10.5 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
10.5.1
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
10.5.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
10.6
CPU During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 116
10.7
Instruction Set Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 117
10.8
Opcode Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Section 11. FLASH Memory (FLASH)
11.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
11.2
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
11.3
FLASH Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
11.4
FLASH Page Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 127
11.5
FLASH Mass Erase Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
11.6
FLASH Program/Read Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 128
11.7 FLASH Block Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 130
11.7.1
FLASH Block Protect Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . 132
11.8
Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
11.9
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
Data Sheet
12
MC68HC908GZ8
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Table of Contents
Section 12. External Interrupt (IRQ)
12.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
12.2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
12.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
12.4
IRQ Pin . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 137
12.5
IRQ Module During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . 137
12.6
IRQ Status and Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
Freescale Semiconductor, Inc...
Section 13. Keyboard Interrupt Module (KBI)
13.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
13.2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
13.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 139
13.4
Keyboard Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 141
13.5 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
13.5.1
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
13.5.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
13.6
Keyboard Module During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . 142
13.7 I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
13.7.1
Keyboard Status and Control Register . . . . . . . . . . . . . . . . . . . . . . 143
13.7.2
Keyboard Interrupt Enable Register . . . . . . . . . . . . . . . . . . . . . . . . 144
Section 14. Low-Voltage Inhibit (LVI)
14.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
14.2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
14.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.3.1
Polled LVI Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.3.2
Forced Reset Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.3.3
Voltage Hysteresis Protection. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
14.3.4
LVI Trip Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
145
147
147
147
147
14.4
LVI Status Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
14.5
LVI Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
14.6 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
14.6.1
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
14.6.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 148
Section 15. Monitor ROM (MON)
15.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
15.2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 149
MC68HC908GZ8
MOTOROLA
Data Sheet
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
13
Freescale Semiconductor, Inc.
Table of Contents
15.3 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.3.1
Normal Monitor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.3.2
Forced Monitor Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.3.3
Monitor Vectors. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.3.4
Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.3.5
Break Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.3.6
Baud Rate. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.3.7
Commands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
15.4
149
154
154
154
155
155
155
156
Security. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 159
Freescale Semiconductor, Inc...
Section 16. MSCAN08 Controller (MSCAN08)
16.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
16.2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 161
16.3
External Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 162
16.4 Message Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16.4.1
Background. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16.4.2
Receive Structures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16.4.3
Transmit Structures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16.5
163
163
163
165
Identifier Acceptance Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 166
16.6 Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
16.6.1
Interrupt Acknowledge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 170
16.6.2
Interrupt Vectors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
16.7
Protocol Violation Protection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 171
16.8 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16.8.1
MSCAN08 Sleep Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16.8.2
MSCAN08 Soft Reset Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16.8.3
MSCAN08 Power-Down Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16.8.4
CPU Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16.8.5
Programmable Wakeup Function . . . . . . . . . . . . . . . . . . . . . . . . . .
16.9
172
172
174
174
174
174
Timer Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
16.10 Clock System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 175
16.11 Memory Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 178
16.12 Programmer’s Model of Message Storage . . . . . . . . . . . . . . . . . . . . . .
16.12.1
Message Buffer Outline . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16.12.2
Identifier Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16.12.3
Data Length Register (DLR) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
16.12.4
Data Segment Registers (DSRn) . . . . . . . . . . . . . . . . . . . . . . . . . .
16.12.5
Transmit Buffer Priority Registers. . . . . . . . . . . . . . . . . . . . . . . . . .
179
180
181
182
182
183
16.13 Programmer’s Model of Control Registers . . . . . . . . . . . . . . . . . . . . . .
16.13.1
MSCAN08 Module Control Register 0 . . . . . . . . . . . . . . . . . . . . . .
16.13.2
MSCAN08 Module Control Register 1 . . . . . . . . . . . . . . . . . . . . . .
16.13.3
MSCAN08 Bus Timing Register 0 . . . . . . . . . . . . . . . . . . . . . . . . .
183
185
186
187
Data Sheet
14
MC68HC908GZ8
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Table of Contents
16.13.4
16.13.5
16.13.6
16.13.7
16.13.8
16.13.9
16.13.10
16.13.11
16.13.12
16.13.13
MSCAN08 Bus Timing Register 1 . . . . . . . . . . . . . . . . . . . . . . . . .
MSCAN08 Receiver Flag Register (CRFLG) . . . . . . . . . . . . . . . . .
MSCAN08 Receiver Interrupt Enable Register . . . . . . . . . . . . . . .
MSCAN08 Transmitter Flag Register . . . . . . . . . . . . . . . . . . . . . . .
MSCAN08 Transmitter Control Register. . . . . . . . . . . . . . . . . . . . .
MSCAN08 Identifier Acceptance Control Register . . . . . . . . . . . . .
MSCAN08 Receive Error Counter . . . . . . . . . . . . . . . . . . . . . . . . .
MSCAN08 Transmit Error Counter . . . . . . . . . . . . . . . . . . . . . . . . .
MSCAN08 Identifier Acceptance Registers . . . . . . . . . . . . . . . . . .
MSCAN08 Identifier Mask Registers (CIDMR0–CIDMR3) . . . . . . .
188
189
191
192
193
194
195
195
196
197
Freescale Semiconductor, Inc...
Section 17. Input/Output (I/O) Ports
17.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 199
17.2 Port A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17.2.1
Port A Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17.2.2
Data Direction Register A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17.2.3
Port A Input Pullup Enable Register . . . . . . . . . . . . . . . . . . . . . . . .
202
202
202
204
17.3 Port B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
17.3.1
Port B Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 204
17.3.2
Data Direction Register B . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 205
17.4 Port C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17.4.1
Port C Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17.4.2
Data Direction Register C . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17.4.3
Port C Input Pullup Enable Register . . . . . . . . . . . . . . . . . . . . . . . .
207
207
208
209
17.5 Port D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17.5.1
Port D Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17.5.2
Data Direction Register D . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
17.5.3
Port D Input Pullup Enable Register . . . . . . . . . . . . . . . . . . . . . . . .
210
210
211
213
17.6 Port E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
17.6.1
Port E Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
17.6.2
Data Direction Register E . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 214
Section 18. Random-Access Memory (RAM)
18.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
18.2
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
Section 19. Enhanced Serial Communications
Interface (ESCI) Module
19.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
19.2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 219
19.3
Pin Name Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
19.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 220
19.4.1
Data Format . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 223
MC68HC908GZ8
MOTOROLA
Data Sheet
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
15
Freescale Semiconductor, Inc.
Table of Contents
Freescale Semiconductor, Inc...
19.4.2
19.4.2.1
19.4.2.2
19.4.2.3
19.4.2.4
19.4.2.5
19.4.2.6
19.4.3
19.4.3.1
19.4.3.2
19.4.3.3
19.4.3.4
19.4.3.5
19.4.3.6
19.4.3.7
19.4.3.8
Transmitter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Character Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Character Transmission . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Break Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Idle Characters . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Inversion of Transmitted Output . . . . . . . . . . . . . . . . . . . . . . . . .
Transmitter Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Receiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Character Length . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Character Reception . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Sampling. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Framing Errors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Baud Rate Tolerance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Receiver Wakeup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Receiver Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Error Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
223
223
223
225
226
226
226
226
228
228
228
230
230
232
233
233
19.5 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
19.5.1
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 233
19.5.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234
19.6
ESCI During Break Module Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . 234
19.7 I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234
19.7.1
PTE0/TxD (Transmit Data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234
19.7.2
PTE1/RxD (Receive Data) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 234
19.8 I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19.8.1
ESCI Control Register 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19.8.2
ESCI Control Register 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19.8.3
ESCI Control Register 3 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19.8.4
ESCI Status Register 1. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19.8.5
ESCI Status Register 2. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19.8.6
ESCI Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19.8.7
ESCI Baud Rate Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19.8.8
ESCI Prescaler Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
235
235
237
239
240
243
244
244
246
19.9 ESCI Arbiter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19.9.1
ESCI Arbiter Control Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19.9.2
ESCI Arbiter Data Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19.9.3
Bit Time Measurement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
19.9.4
Arbitration Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
250
250
251
251
253
Section 20. System Integration Module (SIM)
20.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
20.2 SIM Bus Clock Control and Generation . . . . . . . . . . . . . . . . . . . . . . . .
20.2.1
Bus Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20.2.2
Clock Startup from POR or LVI Reset . . . . . . . . . . . . . . . . . . . . . .
20.2.3
Clocks in Stop Mode and Wait Mode . . . . . . . . . . . . . . . . . . . . . . .
Data Sheet
16
257
257
257
258
MC68HC908GZ8
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Table of Contents
20.3 Reset and System Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20.3.1
External Pin Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20.3.2
Active Resets from Internal Sources . . . . . . . . . . . . . . . . . . . . . . .
20.3.2.1
Power-On Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20.3.2.2
Computer Operating Properly (COP) Reset . . . . . . . . . . . . . . . .
20.3.2.3
Illegal Opcode Reset. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20.3.2.4
Illegal Address Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20.3.2.5
Low-Voltage Inhibit (LVI) Reset . . . . . . . . . . . . . . . . . . . . . . . . .
20.3.2.6
Monitor Mode Entry Module Reset (MODRST). . . . . . . . . . . . . .
258
259
259
260
261
261
261
262
262
20.4 SIM Counter . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20.4.1
SIM Counter During Power-On Reset . . . . . . . . . . . . . . . . . . . . . .
20.4.2
SIM Counter During Stop Mode Recovery . . . . . . . . . . . . . . . . . . .
20.4.3
SIM Counter and Reset States . . . . . . . . . . . . . . . . . . . . . . . . . . . .
262
262
262
262
20.5 Exception Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20.5.1
Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20.5.1.1
Hardware Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20.5.1.2
SWI Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20.5.1.3
Interrupt Status Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20.5.2
Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20.5.3
Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20.5.4
Status Flag Protection in Break Mode . . . . . . . . . . . . . . . . . . . . . .
263
263
265
266
266
268
268
268
20.6 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
20.6.1
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 268
20.6.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 270
20.7 SIM Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20.7.1
Break Status Register. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20.7.2
SIM Reset Status Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
20.7.3
Break Flag Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
271
271
272
273
Section 21. Serial Peripheral Interface (SPI) Module
21.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
21.2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
21.3
Pin Name Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
21.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
21.4.1
Master Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278
21.4.2
Slave Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 278
21.5 Transmission Formats . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21.5.1
Clock Phase and Polarity Controls . . . . . . . . . . . . . . . . . . . . . . . . .
21.5.2
Transmission Format When CPHA = 0. . . . . . . . . . . . . . . . . . . . . .
21.5.3
Transmission Format When CPHA = 1. . . . . . . . . . . . . . . . . . . . . .
21.5.4
Transmission Initiation Latency . . . . . . . . . . . . . . . . . . . . . . . . . . .
21.6
Queuing Transmission Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 283
MC68HC908GZ8
MOTOROLA
279
279
280
281
282
Data Sheet
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
17
Freescale Semiconductor, Inc.
Table of Contents
21.7 Error Conditions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284
21.7.1
Overflow Error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 284
21.7.2
Mode Fault Error. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 285
21.8
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 287
21.9
Resetting the SPI . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
21.10 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
21.10.1
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 289
21.10.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290
Freescale Semiconductor, Inc...
21.11 SPI During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 290
21.12 I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21.12.1
MISO (Master In/Slave Out) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21.12.2
MOSI (Master Out/Slave In) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21.12.3
SPSCK (Serial Clock) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21.12.4
SS (Slave Select) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21.12.5
CGND (Clock Ground) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
290
291
291
291
291
293
21.13 I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21.13.1
SPI Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
21.13.2
SPI Status and Control Register. . . . . . . . . . . . . . . . . . . . . . . . . . .
21.13.3
SPI Data Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
293
293
294
297
Section 22. Timebase Module (TBM)
22.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299
22.2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299
22.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299
22.4
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300
22.5
TBM Interrupt Rate . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301
22.6 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301
22.6.1
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 301
22.6.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302
22.7
Timebase Control Register . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 302
Section 23. Timer Interface Module (TIM)
23.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 305
23.2
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
23.3
Pin Name Conventions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 306
23.4 Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23.4.1
TIM Counter Prescaler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23.4.2
Input Capture . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23.4.3
Output Compare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23.4.3.1
Unbuffered Output Compare. . . . . . . . . . . . . . . . . . . . . . . . . . . .
23.4.3.2
Buffered Output Compare . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Data Sheet
18
306
309
309
309
309
310
MC68HC908GZ8
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Table of Contents
23.4.4
23.4.4.1
23.4.4.2
23.4.4.3
23.5
Pulse Width Modulation (PWM) . . . . . . . . . . . . . . . . . . . . . . . . . . .
Unbuffered PWM Signal Generation. . . . . . . . . . . . . . . . . . . . . .
Buffered PWM Signal Generation . . . . . . . . . . . . . . . . . . . . . . . .
PWM Initialization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
310
311
312
312
Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
23.6 Low-Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
23.6.1
Wait Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314
23.6.2
Stop Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314
23.7
TIM During Break Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314
23.8
I/O Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 314
Freescale Semiconductor, Inc...
23.9 I/O Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23.9.1
TIM Status and Control Register . . . . . . . . . . . . . . . . . . . . . . . . . .
23.9.2
TIM Counter Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
23.9.3
TIM Counter Modulo Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . .
23.9.4
TIM Channel Status and Control Registers . . . . . . . . . . . . . . . . . .
23.9.5
TIM Channel Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
315
315
317
317
318
321
Section 24. Electrical Specifications
24.1
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323
24.2
Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 323
24.3
Functional Operating Range. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324
24.4
Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 324
24.5
5-Vdc Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 325
24.6
3.3-Vdc Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 327
24.7
5.0-Volt Control Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
24.8
3.3-Volt Control Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
24.9 Clock Generation Module Characteristics . . . . . . . . . . . . . . . . . . . . . . 330
24.9.1
CGM Component Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . 330
24.9.2
CGM Electrical Specifications. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 330
24.10 5.0-Volt ADC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 331
24.11 3.3-Volt ADC Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332
24.12 5.0-Volt SPI Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 333
24.13 3.3-Volt SPI Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 334
24.14 Timer Interface Module Characteristics . . . . . . . . . . . . . . . . . . . . . . . . 337
24.15 Memory Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 338
MC68HC908GZ8
MOTOROLA
Data Sheet
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
19
Freescale Semiconductor, Inc.
Table of Contents
Section 25. Ordering Information
and Mechanical Specifications
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339
25.2
MC Order Numbers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 339
25.3
32-Pin Low-Profile Quad Flat Pack (LQFP) . . . . . . . . . . . . . . . . . . . . . 340
25.4
48-Pin Low-Profile Quad Flat Pack (LQFP) . . . . . . . . . . . . . . . . . . . . . 341
Freescale Semiconductor, Inc...
25.1
Data Sheet
20
MC68HC908GZ8
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 1. General Description
Freescale Semiconductor, Inc...
1.1 Introduction
The MC68HC908GZ8 is a member of the low-cost, high-performance M68HC08
Family of 8-bit microcontroller units (MCUs). All MCUs in the family use the
enhanced M68HC08 central processor unit (CPU08) and are available with a
variety of modules, memory sizes and types, and package types.
1.2 Features
For convenience, features have been organized to reflect:
• Standard features of the MC68HC908GZ8
• Features of the CPU08
1.2.1 Standard Features of the MC68HC908GZ8
Features of the MC68HC908GZ8 include:
• High-performance M68HC08 architecture optimized for
C-compilers
• Fully upward-compatible object code with M6805, M146805, and M68HC05
Families
• 8-MHz internal bus frequency
• Clock generation module supporting 1-MHz to 8-MHz crystals
• MSCAN08 (Motorola scalable controller area network) controller
(implementing 2.0b protocol as defined in BOSCH specification dated
September 1991)
• FLASH program memory security(1)
• On-chip programming firmware for use with host personal computer which
does not require high voltage for entry
• In-system programming (ISP)
• System protection features:
– Optional computer operating properly (COP) reset
– Low-voltage detection with optional reset and selectable trip points for
3.3-V and 5.0-V operation
– Illegal opcode detection with reset
– Illegal address detection with reset
1. No security feature is absolutely secure. However, Motorola’s strategy is to make reading or
copying the FLASH difficult for unauthorized users.
MC68HC908GZ8
MOTOROLA
Data Sheet
General Description
For More Information On This Product,
Go to: www.freescale.com
21
Freescale Semiconductor, Inc.
General Description
•
•
Freescale Semiconductor, Inc...
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Low-power design; fully static with stop and wait modes
Standard low-power modes of operation:
– Wait mode
– Stop mode
Master reset pin and power-on reset (POR)
8 Kbytes of on-chip FLASH memory
1 Kbyte of on-chip random-access memory (RAM)
406 bytes of FLASH programming routines read-only memory (ROM)
Serial peripheral interface (SPI) module
Enhanced serial communications interface (ESCI) module
Fine adjust baud rate prescalers for precise control of baud rate
Arbiter module:
– Measurement of received bit timings for baud rate recovery without use
of external timer
– Bitwise arbitration for arbitrated UART communications
LIN specific enhanced features:
– Generation of LIN 1.2 break symbols without extra software steps on
each message
– Break detection filtering to prevent false interrupts
Two 16-bit, 2-channel timer interface modules (TIM1 and TIM2) with
selectable input capture, output compare, and pulse-width modulation
(PWM) capability on each channel
8-channel, 10-bit successive approximation analog-to-digital converter
(ADC)
BREAK (BRK) module to allow single breakpoint setting during
in-circuit debugging
Internal pullups on IRQ and RST to reduce customer system cost
Up to 37 general-purpose input/output (I/O) pins, including:
– 28 shared-function I/O pins
– Up to nine dedicated I/O pins, depending on package choice
Selectable pullups on inputs only on ports A, C, and D. Selection is on an
individual port bit basis. During output mode, pullups are disengaged.
High current 10-mA sink/source capability on all port pins
Higher current 20-mA sink/source capability on PTC0–PTC4
Timebase module (TBM) with clock prescaler circuitry for eight user
selectable periodic real-time interrupts with optional active clock source
during stop mode for periodic wakeup from stop using an external crystal
User selection of having the oscillator enabled or disabled during stop mode
8-bit keyboard wakeup port
2 mA maximum current injection on all port pins to maintain input protection
Data Sheet
22
MC68HC908GZ8
General Description
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
General Description
MCU Block Diagram
•
•
Freescale Semiconductor, Inc...
•
Available packages:
– 32-pin quad flat pack (LQFP)
– 48-pin quad flat pack (LQFP)
Specific features of the MC68HC908GZ8 in 32-pin LQFP are:
– Port A is only 4 bits: PTA0–PTA3; 4-pin keyboard interrupt (KBI) module
– Port B is only 6 bits: PTB0–PTB5; 6-channel ADC module
– Port C is only 2 bits: PTC0–PTC1; shared with MSCAN08 module
– Port D is only 7 bits: PTD0–PTD6; shared with SPI, TIM1, and TIM2
modules
– Port E is only 2 bits: PTE0–PTE1; shared with ESCI module
Specific features of the MC68HC908GZ8 in 48-pin LQFP are:
– Port A is 8 bits: PTA0–PTA7; 8-pin KBI module
– Port B is 8 bits: PTB0–PTB7; 8-channel ADC module
– Port C is only 7 bits: PTC0–PTC6; shared with MSCAN08 module
– Port D is 8 bits: PTD0–PTD7; shared with SPI, TIM1, and TIM2 modules
– Port E is only 6 bits: PTE0–PTE5; shared with ESCI module
1.2.2 Features of the CPU08
Features of the CPU08 include:
• Enhanced HC05 programming model
• Extensive loop control functions
• 16 addressing modes (eight more than the HC05)
• 16-bit index register and stack pointer
• Memory-to-memory data transfers
• Fast 8 × 8 multiply instruction
• Fast 16/8 divide instruction
• Binary-coded decimal (BCD) instructions
• Optimization for controller applications
• Efficient C language support
1.3 MCU Block Diagram
Figure 1-1 shows the structure of the MC68HC908GZ8.
1.4 Pin Assignments
Figure 1-2 and Figure 1-3 illustrate the pin assignments for the 32-pin LQFP and
48-pin LQFP respectively.
MC68HC908GZ8
MOTOROLA
Data Sheet
General Description
For More Information On This Product,
Go to: www.freescale.com
23
Data Sheet
For More Information On This Product,
Go to: www.freescale.com
General Description
POWER
POWER-ON RESET
MODULE
1. Ports are software configurable with pullup device if input port.
2. Higher current drive port pins
3. Pin contains integrated pullup device
VDD
VSS
VDDA
VSSA
VDDAD/VREFL
10-BIT ANALOG-TO-DIGITAL
CONVERTER MODULE
SINGLE EXTERNAL
INTERRUPT MODULE
IRQ(3)
VDDAD/VREFH
SYSTEM INTEGRATION
MODULE
Figure 1-1. MCU Block Diagram
MSCAN08 MODULE
CONFIGURATION
REGISTER 1–2
MODULE
MEMORY MAP
MODULE
DATA BUS SWITCH
MODULE
MONITOR MODULE
SERIAL PERIPHERAL
INTERFACE MODULE
COMPUTER OPERATING
PROPERLY MODULE
PHASE LOCKED LOOP
1–8 MHz OSCILLATOR
ENHANCED SERIAL
COMUNICATIONS
INTERFACE MODULE
2-CHANNEL TIMER
INTERFACE MODULE 2
2-CHANNEL TIMER
INTERFACE MODULE 1
8-BIT KEYBOARD
INTERRUPT MODULE
DUAL VOLTAGE
LOW-VOLTAGE INHIBIT
MODULE
SINGLE BREAKPOINT
BREAK MODULE
PROGRAMMABLE TIMEBASE
MODULE
CLOCK GENERATOR MODULE
RST(3)
CGMXFC
OSC1
OSC2
USER FLASH VECTOR SPACE — 44 BYTES
FLASH PROGRAMMING ROUTINES ROM — 406 BYTES
MONITOR ROM — 350 BYTES
USER RAM — 1024 BYTES
USER FLASH — 7936 BYTES
CONTROL AND STATUS REGISTERS — 64 BYTES
ARITHMETIC/LOGIC
UNIT (ALU)
PTD7/T2CH1(1)
PTD6/T2CH0(1)
PTD5/T1CH1(1)
PTD4/T1CH0(1)
PTD3/SPSCK(1)
PTD2/MOSI(1)
PTD1/MISO(1)
PTD0/SS(1)
PTE5–PTE2
PTE1/RxD
PTE0/TxD
MONITOR MODE ENTRY
MODULE
SECURITY
MODULE
PTC6(1)
PTC5(1)
PTC4(1), (2)
PTC3(1), (2)
PTC2(1), (2)
PTC1/CANRX(1), (2)
PTC0/CANTX(1), (2)
PTA7/KBD7–PTA0/KBD0(1)
PTB7/AD7
PTB6/AD6
PTB5/AD5
PTB4/AD4
PTB3/AD3
PTB2/AD2
PTB1/AD1
PTB0/AD0
DDRB
CPU
REGISTERS
DDRC
DDRD
INTERNAL BUS
DDRA
PORTB
PORTC
PORTD
DDRE
24
PORTE
M68HC08 CPU
PORTA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
General Description
MC68HC908GZ8
MOTOROLA
Freescale Semiconductor, Inc.
OSC2
CGMXFC
VSSA
VDDA
PTC1/CANRX
PTC0/CANTX
PTA3/KBD3
30
29
28
27
26
25
1
24
PTA2/KBD2
VDDAD/VREFH
PTD1/MISO
6
19
PTB5/AD5
PTD2/MOSI
7
18
PTB4/AD4
PTD3/SPSCK
8
17
PTB3/AD3
16
20
PTB2/AD2
5
15
PTD0/SS
PTB1/AD1
VSSAD/VREFL
14
21
PTB0/AD0
4
13
IRQ
PTD6/T2CH0
PTA0/KBD0
12
22
PTD5/T1CH1
3
11
PTE1/RxD
PTD4/T1CH0
PTA1/KBD1
10
23
VDD
2
9
PTE0/TxD
VSS
Freescale Semiconductor, Inc...
RST
31
32 OSC1
General Description
Pin Assignments
CGMXFC
VSSA
VDDA
PTC1/CANRX
PTC0/CANTX
PTA7/KBD7
PTA6/KBD6
PTA5/KBD5
PTA4/KBD4
46
45
44
43
42
41
40
39
38
37 PTA3/KBD3
OSC2
RST 1
47
48 OSC1
Figure 1-2. 32-Pin LQFP Pin Assignments
36 PTA2/KBD2
PTE5
7
30
VDDAD/VREFH
IRQ
8
29
PTB7/AD7
PTD0/SS
9
28
PTB6/AD6
PTD1/MISO
10
27
PTB5/AD5
PTD2/MOSI
11
26
PTB4/AD4
25 PTB3/AD3
PTB2/AD2 24
VSS 13
PTD3/SPSCK 12
23
VSSAD/VREFL
PTB1/AD1
31
22
6
PTB0/AD0
PTE4
21
PTC5
PTC4
32
20
5
PTC3
PTE3
19
PTC6
18
33
PTC2
4
PTD7/T2CH1
PTE2
17
PTA0/KBD0
PTD6/T2CH0
34
16
3
PTD5/T1CH1
PTE1/RxD
15
PTA1/KBD1
PTD4/T1CH0
35
14
2
VDD
PTE0/TxD
Figure 1-3. 48-Pin LQFP Pin Assignments
MC68HC908GZ8
MOTOROLA
Data Sheet
General Description
For More Information On This Product,
Go to: www.freescale.com
25
Freescale Semiconductor, Inc.
General Description
1.5 Pin Functions
Descriptions of the pin functions are provided here.
1.5.1 Power Supply Pins (VDD and VSS)
Freescale Semiconductor, Inc...
VDD and VSS are the power supply and ground pins. The MCU operates from a
single power supply.
Fast signal transitions on MCU pins place high, short-duration current demands on
the power supply. To prevent noise problems, take special care to provide power
supply bypassing at the MCU as Figure 1-4 shows. Place the C1 bypass capacitor
as close to the MCU as possible. Use a high-frequency-response ceramic
capacitor for C1. C2 is an optional bulk current bypass capacitor for use in
applications that require the port pins to source high current levels.
MCU
VSS
VDD
C1
0.1 µF
+
C2
VDD
Note: Component values shown represent typical applications.
Figure 1-4. Power Supply Bypassing
1.5.2 Oscillator Pins (OSC1 and OSC2)
OSC1 and OSC2 are the connections for an external crystal, resonator, or clock
circuit. See Section 7. Clock Generator Module (CGM).
1.5.3 External Reset Pin (RST)
A logic 0 on the RST pin forces the MCU to a known startup state. RST is
bidirectional, allowing a reset of the entire system. It is driven low when any
internal reset source is asserted. This pin contains an internal pullup resistor. See
Section 20. System Integration Module (SIM).
Data Sheet
26
MC68HC908GZ8
General Description
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
General Description
Pin Functions
1.5.4 External Interrupt Pin (IRQ)
IRQ is an asynchronous external interrupt pin. This pin contains an internal pullup
resistor. See Section 12. External Interrupt (IRQ).
1.5.5 CGM Power Supply Pins (VDDA and VSSA)
VDDA and VSSA are the power supply pins for the analog portion of the clock
generator module (CGM). Decoupling of these pins should be as per the digital
supply. See Section 7. Clock Generator Module (CGM).
Freescale Semiconductor, Inc...
1.5.6 External Filter Capacitor Pin (VCGMXFC)
CGMXFC is an external filter capacitor connection for the CGM. See
Section 7. Clock Generator Module (CGM).
1.5.7 ADC Power Supply/Reference Pins (VDDAD/VREFH and VSSAD/VREFL)
VDDAD and VSSAD are the power supply pins to the analog-to-digital converter
(ADC). VREFH and VREFL are the reference voltage pins for the ADC. VREFH is the
high reference supply for the ADC, and by default the VDDAD/VREFH pin should be
externally filtered and connected to the same voltage potential as VDD. VREFL is the
low reference supply for the ADC, and by default the VSSAD/VREFL pin should be
connected to the same voltage potential as VSS. See Section 5. Analog-to-Digital
Converter (ADC).
1.5.8 Port A Input/Output (I/O) Pins (PTA7/KBD7–PTA0/KBD0)
PTA7–PTA0 are general-purpose, bidirectional I/O port pins. Any or all of the port
A pins can be programmed to serve as keyboard interrupt pins. PTA7–PTA4 are
only available on the 48-pin LQFP package. See Section 17. Input/Output (I/O)
Ports and Section 13. Keyboard Interrupt Module (KBI).
These port pins also have selectable pullups when configured for input mode. The
pullups are disengaged when configured for output mode. The pullups are
selectable on an individual port bit basis.
1.5.9 Port B I/O Pins (PTB7/AD7–PTB0/AD0)
PTB7–PTB0 are general-purpose, bidirectional I/O port pins that can also be used
for analog-to-digital converter (ADC) inputs. PTB7–PTB4 are only available on the
48-pin LQFP package. See Section 17. Input/Output (I/O) Ports and Section 5.
Analog-to-Digital Converter (ADC).
MC68HC908GZ8
MOTOROLA
Data Sheet
General Description
For More Information On This Product,
Go to: www.freescale.com
27
Freescale Semiconductor, Inc.
General Description
1.5.10 Port C I/O Pins (PTC6–PTC0/CANTX)
PTC6 and PTC5 are general-purpose, bidirectional I/O port pins. PTC4–PTC0 are
general-purpose, bidirectional I/O port pins that contain higher current sink/source
capability. PTC6–PTC2 are only available on the 48-pin LQFP package. See
Section 17. Input/Output (I/O) Ports.
PTC1 and PTC0 can be programmed to be MSCAN08 pins.
Freescale Semiconductor, Inc...
These port pins also have selectable pullups when configured for input mode. The
pullups are disengaged when configured for output mode. The pullups are
selectable on an individual port bit basis.
1.5.11 Port D I/O Pins (PTD7/T2CH1–PTD0/SS)
PTD7–PTD0 are special-function, bidirectional I/O port pins. PTD3–PTD0 can be
programmed to be serial peripheral interface (SPI) pins, while PTD7–PTD4 can be
individually programmed to be timer interface module (TIM1 and TIM2) pins. PTD7
is only available on the 48-pin LQFP package. See Section 23. Timer Interface
Module (TIM), Section 21. Serial Peripheral Interface (SPI) Module, and
Section 17. Input/Output (I/O) Ports.
These port pins also have selectable pullups when configured for input mode. The
pullups are disengaged when configured for output mode. The pullups are
selectable on an individual port bit basis.
1.5.12 Port E I/O Pins (PTE5–PTE2, PTE1/RxD, and PTE0/TxD)
PTE5–PTE0 are general-purpose, bidirectional I/O port pins. PTE1 and PTE0 can
also be programmed to be enhanced serial communications interface (ESCI) pins.
PTE5–PTE2 are only available on the 48-pin LQFP package. See Section 19.
Enhanced Serial Communications Interface (ESCI) Module and Section 17.
Input/Output (I/O) Ports.
NOTE:
Any unused inputs and I/O ports should be tied to an appropriate logic level (either
VDD or VSS). Although the I/O ports of the MC68HC908GZ8 do not require
termination, termination is recommended to reduce the possibility of static damage.
Data Sheet
28
MC68HC908GZ8
General Description
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 2. Memory Map
2.1 Introduction
Freescale Semiconductor, Inc...
The CPU08 can address 64 Kbytes of memory space. The memory map, shown in
Figure 2-1, includes:
•
7680 bytes of user FLASH memory
•
1024 bytes of random-access memory (RAM)
•
406 bytes of FLASH programming routines read-only memory (ROM)
•
44 bytes of user-defined vectors
•
350 bytes of monitor ROM
2.2 Unimplemented Memory Locations
Accessing an unimplemented location can cause an illegal address reset. In the
memory map (Figure 2-1) and in register figures in this document, unimplemented
locations are shaded.
2.3 Reserved Memory Locations
Accessing a reserved location can have unpredictable effects on microcontroller
(MCU) operation. In the Figure 2-1 and in register figures in this document,
reserved locations are marked with the word Reserved or with the
letter R.
2.4 Input/Output (I/O) Section
Most of the control, status, and data registers are in the zero page area of
$0000–$003F. Additional I/O registers have these addresses:
•
$FE00; break status register, BSR
•
$FE01; SIM reset status register, SRSR
•
$FE02; break auxiliary register, BRKAR
•
$FE03; break flag control register, BFCR
•
$FE04; interrupt status register 1, INT1
•
$FE05; interrupt status register 2, INT2
•
$FE06; interrupt status register 3, INT3
MC68HC908GZ8
MOTOROLA
Data Sheet
Memory Map
For More Information On This Product,
Go to: www.freescale.com
29
Freescale Semiconductor, Inc.
Memory Map
•
$FE07; reserved
•
$FE08; FLASH control register, FLCR
•
$FE09; break address register high, BRKH
•
$FE0A; break address register low, BRKL
•
$FE0B; break status and control register, BRKSCR
•
$FE0C; LVI status register, LVISR
•
$FF7E; FLASH block protect register, FLBPR
Freescale Semiconductor, Inc...
Data registers are shown in Figure 2-2. Table 2-1 is a list of vector locations.
$0000
I/O REGISTERS
64 BYTES
↓
$003F
$0040
RAM
1024 BYTES
↓
$043F
$0440
UNIMPLEMENTED
192 BYTES
↓
$04FF
$0500
↓
MSCAN08 CONTROL AND MESSAGE BUFFER
128 BYTES
$057F
$0580
UNIMPLEMENTED
5760 BYTES
↓
$1BFF
$1C00
↓
FLASH PROGRAMMING ROUTINES ROM
406 BYTES
$1D95
$1D96
UNIMPLEMENTED
49,770 BYTES
↓
$DFFF
$E000
FLASH MEMORY
7680 BYTES
↓
$FDFF
$FE00
SIM BREAK STATUS REGISTER (SBSR)
Figure 2-1. Memory Map
Data Sheet
30
MC68HC908GZ8
Memory Map
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Memory Map
Input/Output (I/O) Section
$FE01
SIM RESET STATUS REGISTER (SRSR)
$FE02
RESERVED
$FE03
SIM BREAK FLAG CONTROL REGISTER (SBFCR)
$FE04
INTERRUPT STATUS REGISTER 1 (INT1)
$FE05
INTERRUPT STATUS REGISTER 2 (INT2)
$FE06
INTERRUPT STATUS REGISTER 3 (INT3)
$FE07
RESERVED
$FE08
FLASH CONTROL REGISTER (FLCR)
$FE09
BREAK ADDRESS REGISTER HIGH (BRKH)
$FE0A
BREAK ADDRESS REGISTER LOW (BRKL)
$FE0B
BREAK STATUS AND CONTROL REGISTER (BRKSCR)
$FE0C
LVI STATUS REGISTER (LVISR)
$FE0D
UNIMPLEMENTED
3 BYTES
↓
$FE0F
$FE10
↓
$FE1F
UNIMPLEMENTED
16 BYTES
RESERVED FOR COMPATIBILITY WITH MONITOR CODE
FOR A-FAMILY PART
$FE20
MONITOR ROM
350 BYTES
↓
$FF7D
$FF7E
FLASH BLOCK PROTECT REGISTER (FLBPR)
$FF7F
UNIMPLEMENTED
85 BYTES
↓
$FFD3
$FFD4
FLASH VECTORS
44 BYTES
↓
$FFFF(1)
1. $FFF6–$FFFD used for eight security bytes
Figure 2-1. Memory Map (Continued)
MC68HC908GZ8
MOTOROLA
Data Sheet
Memory Map
For More Information On This Product,
Go to: www.freescale.com
31
Freescale Semiconductor, Inc.
Memory Map
Addr.
$0000
Freescale Semiconductor, Inc...
$0001
Register Name
Port A Data Register Read:
(PTA) Write:
See page 202. Reset:
Port B Data Register Read:
(PTB) Write:
See page 204. Reset:
$0002
Port C Data Register Read:
(PTC) Write:
See page 207. Reset:
$0003
Port D Data Register Read:
(PTD) Write:
See page 210. Reset:
$0004
$0005
Data Direction Register A Read:
(DDRA) Write:
See page 202. Reset:
Data Direction Register B Read:
(DDRB) Write:
See page 205. Reset:
$0006
Data Direction Register C Read:
(DDRC) Write:
See page 208. Reset:
$0007
Data Direction Register D Read:
(DDRD) Write:
See page 211. Reset:
$0008
$0009
$000A
Port E Data Register Read:
(PTE) Write:
See page 213. Reset:
ESCI Prescaler Register Read:
(SCPSC) Write:
See page 246. Reset:
ESCI Arbiter Control Read:
Register (SCIACTL) Write:
See page 250. Reset:
Bit 7
6
5
4
3
2
1
Bit 0
PTA7
PTA6
PTA5
PTA4
PTA3
PTA2
PTA1
PTA0
PTB2
PTB1
PTB0
PTC2
PTC1
PTC0
PTD2
PTD1
PTD0
Unaffected by reset
PTB7
PTB6
PTB5
PTB4
PTB3
Unaffected by reset
1
PTC6
PTC5
PTC4
PTC3
Unaffected by reset
PTD7
PTD6
PTD5
PTD4
PTD3
Unaffected by reset
DDRA7
DDRA6
DDRA5
DDRA4
DDRA3
DDRA2
DDRA1
DDRA0
0
0
0
0
0
0
0
0
DDRB7
DDRB6
DDRB5
DDRB4
DDRB3
DDRB2
DDRB1
DDRB0
0
0
0
0
0
0
0
0
DDRC6
DDRC5
DDRC4
DDRC3
DDRC2
DDRC1
DDRC0
0
0
0
0
0
0
0
0
DDRD7
DDRD6
DDRD5
DDRD4
DDRD3
DDRD2
DDRD1
DDRD0
0
0
0
0
0
0
0
0
0
0
PTE5
PTE4
PTE3
PTE2
PTE1
PTE0
0
Unaffected by reset
PS2
PS1
PS0
PSSB4
PSSB3
PSSB2
PSSB1
PSSB0
0
0
0
0
0
0
0
0
AM0
ACLK
AFIN
ARUN
AOVFL
ARD8
0
0
0
0
0
0
AM1
0
ALOST
0
= Unimplemented
R = Reserved
U = Unaffected
Figure 2-2. Control, Status, and Data Registers (Sheet 1 of 8)
Data Sheet
32
MC68HC908GZ8
Memory Map
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Memory Map
Input/Output (I/O) Section
Addr.
Register Name
ESCI Arbiter Data Read:
Register (SCIADAT) Write:
See page 251. Reset:
$000B
$000C
Freescale Semiconductor, Inc...
$000D
Data Direction Register E Read:
(DDRE) Write:
See page 214. Reset:
Bit 7
6
5
4
3
2
1
Bit 0
ARD7
ARD6
ARD5
ARD4
ARD3
ARD2
ARD1
ARD0
0
0
0
0
0
0
0
0
0
0
DDRE5
DDRE4
DDRE3
DDRE2
DDRE1
DDRE0
0
0
0
0
0
0
0
0
PTAPUE6
PTAPUE5
PTAPUE4
PTAPUE3
PTAPUE2
PTAPUE1
PTAPUE0
0
0
0
0
0
0
0
PTCPUE6
PTCPUE5
PTCPUE4
PTCPUE3
PTCPUE2
PTCPUE1
PTCPUE0
0
0
0
0
0
0
0
PTDPUE6
PTDPUE5
PTDPUE4
PTDPUE3
PTDPUE2
PTDPUE1
PTDPUE0
0
0
0
0
0
0
0
SPRIE
R
SPMSTR
CPOL
CPHA
SPWOM
SPE
SPTIE
0
0
1
0
1
0
0
0
OVRF
MODF
SPTE
MODFEN
SPR1
SPR0
Port A Input Pullup Enable Read: PTAPUE7
Register (PTAPUE) Write:
See page 204. Reset:
0
$000E
Port C Input Pullup Enable Read:
Register (PTCPUE) Write:
See page 209. Reset:
$000F
Port D Input Pullup Enable Read: PTDPUE7
Register (PTDPUE) Write:
See page 213. Reset:
0
SPI Control Register Read:
(SPCR) Write:
See page 293. Reset:
$0010
SPI Status and Control Read:
Register (SPSCR) Write:
See page 295. Reset:
$0011
$0012
SPI Data Register Read:
(SPDR) Write:
See page 297. Reset:
$0013
ESCI Control Register 1 Read:
(SCC1) Write:
See page 235. Reset:
$0014
$0015
ESCI Control Register 2 Read:
(SCC2) Write:
See page 237. Reset:
0
0
SPRF
ERRIE
0
0
0
0
1
0
0
0
R7
R6
R5
R4
R3
R2
R1
R0
T7
T6
T5
T4
T3
T2
T1
T0
Unaffected by reset
LOOPS
ENSCI
TXINV
M
WAKE
ILTY
PEN
PTY
0
0
0
0
0
0
0
0
SCTIE
TCIE
SCRIE
ILIE
TE
RE
RWU
SBK
0
0
0
0
0
0
0
0
T8
R
R
ORIE
NEIE
FEIE
PEIE
ESCI Control Register 3 Read:
(SCC3) Write:
See page 239. Reset:
R8
U
0
0
0
0
0
0
0
ESCI Status Register 1 Read:
(SCS1) Write:
See page 241. Reset:
SCTE
TC
SCRF
IDLE
OR
NF
FE
PE
1
1
0
0
0
0
0
0
$0016
= Unimplemented
R = Reserved
U = Unaffected
Figure 2-2. Control, Status, and Data Registers (Sheet 2 of 8)
MC68HC908GZ8
MOTOROLA
Data Sheet
Memory Map
For More Information On This Product,
Go to: www.freescale.com
33
Freescale Semiconductor, Inc.
Memory Map
Addr.
Register Name
$0017
ESCI Status Register 2 Read:
(SCS2) Write:
See page 243. Reset:
ESCI Data Register Read:
(SCDR) Write:
See page 244. Reset:
$0018
ESCI Baud Rate Register Read:
(SCBR) Write:
See page 244. Reset:
$0019
Freescale Semiconductor, Inc...
Bit 7
Keyboard Status Read:
and Control Register Write:
(INTKBSCR)
See page 143. Reset:
$001A
$001B
Keyboard Interrupt Enable Read:
Register (INTKBIER) Write:
See page 144. Reset:
$001C
Timebase Module Control Read:
Register (TBCR) Write:
See page 302. Reset:
$001D
$001E
5
4
3
2
1
Bit 0
BKF
RPF
0
0
0
0
0
0
0
0
R7
R6
R5
R4
R3
R2
R1
R0
T7
T6
T5
T4
T3
T2
T1
T0
Unaffected by reset
LINT
LINR
SCP1
SCP0
R
SCR2
SCR1
SCR0
0
0
0
0
0
0
0
0
0
0
0
0
KEYF
0
IMASKK
MODEK
ACKK
0
0
0
0
0
0
0
0
KBIE7
KBIE6
KBIE5
KBIE4
KBIE3
KBIE2
KBIE1
KBIE0
0
0
0
0
0
0
0
0
TBIE
TBON
R
0
0
0
IMASK1
MODE1
0
0
TBIF
0
TBR2
TBR1
TBR0
0
0
0
0
0
IRQ Status and Control Read:
Register (INTSCR) Write:
See page 138. Reset:
0
0
0
0
IRQF1
0
0
0
0
Configuration Register 2 Read:
(CONFIG2)(1) Write:
See page 104.
Reset:
0
0
0
0
0
0
0
0
0
0
0
1
COPRS
LVISTOP
LVIRSTD
LVIPWRD
LVI5OR3
(Note 1)
SSREC
STOP
COPD
0
0
0
0
0
0
0
0
Configuration Register 1 Read:
(CONFIG1)(1) Write:
See page 104. Reset:
$001F
6
TACK
0
ACK1
0
0
MSCAN-E
OSCENINTMCLKSEL
SCIBDSRC
N
STOP
1. One-time writable register after each reset, except LVI5OR3 bit. LVI5OR3 bit is only reset via POR (power-on reset).
TOF
$0020
Timer 1 Status and Control Read:
Register (T1SC) Write:
See page 315. Reset:
0
0
1
0
Bit 15
14
13
12
$0021
Timer 1 Counter Read:
Register High (T1CNTH) Write:
See page 317. Reset:
0
0
0
0
0
0
TOIE
TSTOP
= Unimplemented
0
0
PS2
PS1
0
0
0
0
11
10
9
Bit 8
0
0
0
TRST
R = Reserved
PS0
U = Unaffected
Figure 2-2. Control, Status, and Data Registers (Sheet 3 of 8)
Data Sheet
34
MC68HC908GZ8
Memory Map
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Memory Map
Input/Output (I/O) Section
Addr.
$0022
$0023
Freescale Semiconductor, Inc...
$0024
Register Name
Timer 1 Counter Read:
Register Low (T1CNTL) Write:
See page 317. Reset:
Timer 1 Counter Modulo Read:
Register High (T1MODH) Write:
See page 317. Reset:
Timer 1 Counter Modulo Read:
Register Low (T1MODL) Write:
See page 318. Reset:
Timer 1 Channel 0 Status and Read:
$0025
Control Register (T1SC0) Write:
See page 318. Reset:
$0026
Timer 1 Channel 0 Read:
Register High (T1CH0H) Write:
See page 321. Reset:
Timer 1 Channel 0 Read:
Register Low (T1CH0L) Write:
See page 321. Reset:
$0027
Timer 1 Channel 1 Status and Read:
$0028
Control Register (T1SC1) Write:
See page 318. Reset:
$0029
Timer 1 Channel 1 Read:
Register High (T1CH1H) Write:
See page 322. Reset:
$002A
Timer 1 Channel 1 Read:
Register Low (T1CH1L) Write:
See page 322. Reset:
$002B
$002C
$002D
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
Bit 15
14
13
12
11
10
9
Bit 8
1
1
1
1
1
1
1
1
Bit 7
6
5
4
3
2
1
Bit 0
1
1
1
1
1
1
1
1
CH0IE
MS0B
MS0A
ELS0B
ELS0A
TOV0
CH0MAX
0
0
0
0
0
0
0
0
Bit 15
14
13
12
11
10
9
Bit 8
2
1
Bit 0
CH0F
0
Indeterminate after reset
Bit 7
6
5
4
3
Indeterminate after reset
CH1F
0
0
CH1IE
MS1A
ELS1B
ELS1A
TOV1
CH1MAX
0
0
0
0
0
0
0
0
Bit 15
14
13
12
11
10
9
Bit 8
2
1
Bit 0
PS2
PS1
PS0
Indeterminate after reset
Bit 7
6
5
4
3
Indeterminate after reset
Timer 2 Status and Control Read:
Register (T2SC) Write:
See page 315. Reset:
TOF
0
0
TOIE
TSTOP
0
0
1
0
0
0
0
0
Timer 2 Counter Read:
Register High (T2CNTH) Write:
See page 317. Reset:
Bit 15
14
13
12
11
10
9
Bit 8
0
0
0
0
0
0
0
0
Timer 2 Counter Read:
Register Low (T2CNTL) Write:
See page 317. Reset:
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
0
= Unimplemented
TRST
R = Reserved
U = Unaffected
Figure 2-2. Control, Status, and Data Registers (Sheet 4 of 8)
MC68HC908GZ8
MOTOROLA
Data Sheet
Memory Map
For More Information On This Product,
Go to: www.freescale.com
35
Freescale Semiconductor, Inc.
Memory Map
Addr.
Register Name
Timer 2 Counter Modulo Read:
Register High (T2MODH) Write:
See page 317. Reset:
$002E
Timer 2 Counter Modulo Read:
Register Low (T2MODL) Write:
See page 318. Reset:
$002F
Freescale Semiconductor, Inc...
Timer 2 Channel 0 Status and Read:
$0030
Control Register (T2SC0) Write:
See page 318. Reset:
$0031
Timer 2 Channel 0 Read:
Register High (T2CH0H) Write:
See page 321. Reset:
$0032
Timer 2 Channel 0 Read:
Register Low (T2CH0L) Write:
See page 321. Reset:
$0033
Timer 2 Channel 1 Status and Read:
Control Register (T2SC1) Write:
See page 318. Reset:
Timer 2 Channel 1 Read:
Register High (T2CH1H) Write:
See page 322. Reset:
$0034
Timer 2 Channel 1 Read:
Register Low (T2CH1L) Write:
See page 322. Reset:
$0035
PLL Control Register Read:
(PCTL) Write:
See page 94. Reset:
$0036
PLL Bandwidth Control Read:
Register (PBWC) Write:
See page 96. Reset:
$0037
$0038
PLL Multiplier Select High Read:
Register (PMSH) Write:
See page 97. Reset:
$0039
PLL Multiplier Select Low Read:
Register (PMSL) Write:
See page 98. Reset:
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
1
1
1
1
1
1
1
1
Bit 7
6
5
4
3
2
1
Bit 0
1
1
1
1
1
1
1
1
CH0IE
MS0B
MS0A
ELS0B
ELS0A
TOV0
CH0MAX
0
0
0
0
0
0
0
0
Bit 15
14
13
12
11
10
9
Bit 8
2
1
Bit 0
CH0F
0
Indeterminate after reset
Bit 7
6
5
4
3
Indeterminate after reset
CH1F
0
0
CH1IE
MS1A
ELS1B
ELS1A
TOV1
CH1MAX
0
0
0
0
0
0
0
0
Bit 15
14
13
12
11
10
9
Bit 8
2
1
Bit 0
Indeterminate after reset
Bit 7
6
5
4
3
Indeterminate after reset
PLLIE
0
AUTO
PLLF
PLLON
BCS
R
R
VPR1
VPR0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
MUL11
MUL10
MUL9
MUL8
0
LOCK
ACQ
R
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
MUL7
MUL6
MUL5
MUL4
MUL3
MUL2
MUL1
MUL0
0
0
0
0
U
U
U
U
= Unimplemented
R = Reserved
U = Unaffected
Figure 2-2. Control, Status, and Data Registers (Sheet 5 of 8)
Data Sheet
36
MC68HC908GZ8
Memory Map
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Memory Map
Input/Output (I/O) Section
Addr.
Register Name
Bit 7
6
5
4
3
2
1
Bit 0
VRS7
VRS6
VRS5
VRS4
VRS3
VRS2
VRS1
VRS0
0
1
0
0
0
0
0
0
0
0
0
0
R
R
R
R
0
0
0
0
0
0
0
1
COCO
AIEN
ADCO
ADCH4
ADCH3
ADCH2
ADCH1
ADCH0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
AD9
AD8
$003D
ADC Data High Register Read:
(ADRH) Write:
See page 73. Reset:
AD7
AD6
AD5
AD2
AD1
AD0
$003E
ADC Data Low Register Read:
(ADRL) Write:
See page 73. Reset:
PLL VCO Select Range Read:
Register (PMRS) Write:
See page 98. Reset:
$003A
Read:
Reserved Write:
$003B
Reset:
Freescale Semiconductor, Inc...
$003C
ADC Status and Control Read:
Register (ADSCR) Write:
See page 71. Reset:
ADC Clock Register Read:
(ADCLK) Write:
See page 75. Reset:
$003F
$0500
↓
$0508
MSCAN08
Control Registers
See page 183.
$0509
↓
$050D
Reserved
$050E
↓
$050F
MSCAN08
Error Counters
$0510
↓
$0517
MSCAN08 Identifier Filter
See page 183.
$0518
↓
$053F
Reserved
Unaffected by reset
AD4
A3
Unaffected by reset
ADIV2
ADIV1
ADIV0
ADICLK
MODE1
MODE0
R
0
0
0
0
0
1
0
0
0
MSCAN08 control registers (9 bytes)
Refer to 16.13 Programmer’s Model of Control Registers
Reserved (5 bytes)
MSCAN08 error counters (2 bytes)
MSCAN08 control registers (9 bytes)
Refer to 16.13 Programmer’s Model of Control Registers
Reserved (40 bytes)
= Unimplemented
R = Reserved
U = Unaffected
Figure 2-2. Control, Status, and Data Registers (Sheet 6 of 8)
MC68HC908GZ8
MOTOROLA
Data Sheet
Memory Map
For More Information On This Product,
Go to: www.freescale.com
37
Freescale Semiconductor, Inc.
Memory Map
Freescale Semiconductor, Inc...
Addr.
Register Name
Bit 7
6
5
4
3
2
1
$0540
↓
$054F
MSCAN08 Receive Buffer
See page 179.
MSC08 receive buffer
Refer to 16.12 Programmer’s Model of Message Storage
$0550
↓
$055F
MSCAN08 Transmit Buffer 0
See page 179.
MSC08 transmitter buffer 0
Refer to 16.12 Programmer’s Model of Message Storage
$0560
↓
$056F
MSCAN08 Transmit Buffer 1
See page 179.
MSC08 transmitter buffer 1
Refer to 16.12 Programmer’s Model of Message Storage
$0570
↓
$057F
MSCAN08 Transmit Buffer 2
See page 179.
MSC08 transmitter buffer 2
Refer to 16.12 Programmer’s Model of Message Storage
Break Status Register Read:
(BSR) Write:
See page 81. Reset:
Bit 0
SBSW
R
R
R
R
R
R
0
0
0
0
0
0
0
0
POR
PIN
COP
ILOP
ILAD
MODRST
LVI
0
1
0
0
0
0
0
0
0
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
BCFE
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
Interrupt Status Register 1 Read:
(INT1) Write:
See page 62. Reset:
IF6
IF5
IF4
IF3
IF2
IF1
0
0
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
IF14
IF13
IF12
IF11
IF10
IF9
IF8
IF7
$FE05
Interrupt Status Register 2 Read:
(INT2) Write:
See page 62. Reset:
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
0
0
IF20
IF19
IF18
IF17
IF16
IF15
$FE06
Interrupt Status Register 3 Read:
(INT3) Write:
See page 63. Reset:
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
$FE00
(Note 2)
R
2. Writing a logic 0 clears SBSW.
$FE01
SIM Reset Status Register Read:
(SRSR) Write:
See page 272. POR:
Read:
Reserved Write:
$FE02
Reset:
$FE03
$FE04
Break Flag Control Register Read:
(BFCR) Write:
See page 82. Reset:
= Unimplemented
R = Reserved
U = Unaffected
Figure 2-2. Control, Status, and Data Registers (Sheet 7 of 8)
Data Sheet
38
MC68HC908GZ8
Memory Map
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Memory Map
Input/Output (I/O) Section
Addr.
Register Name
Bit 7
6
5
4
3
2
1
Bit 0
R
R
R
R
R
R
R
R
Reset:
0
0
0
0
0
0
0
0
FLASH Control Register Read:
(FLCR) Write:
See page 126. Reset:
0
0
0
0
HVEN
MASS
ERASE
PGM
0
0
0
0
0
0
0
0
Bit 15
14
13
12
11
10
9
Bit 8
0
0
0
0
0
0
0
0
Bit 7
6
5
4
3
2
1
Bit 0
0
0
Read:
Reserved Write:
$FE07
$FE08
Freescale Semiconductor, Inc...
Break Address Register High Read:
$FE09
(BRKH) Write:
See page 81. Reset:
Break Address Register Low Read:
$FE0A
(BRKL) Write:
See page 81. Reset:
$FE0B
Break Status and Control Read:
Register (BRKSCR) Write:
See page 80. Reset:
$FE0C
$FF7E
LVI Status Register Read:
(LVISR) Write:
See page 147. Reset:
FLASH Block Protect Read:
Register (FLBPR)(3) Write:
See page 132. Reset:
0
0
0
0
0
0
0
0
0
0
0
0
BRKE
BRKA
0
0
0
0
0
0
0
0
LVIOUT
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
BPR7
BPR6
BPR5
BPR4
BPR3
BPR2
BPR1
BPR0
Unaffected by reset
3. Non-volatile FLASH register
$FFFF
COP Control Register Read:
(COPCTL) Write:
See page 109. Reset:
Low byte of reset vector
Writing clears COP counter (any value)
Unaffected by reset
= Unimplemented
R = Reserved
U = Unaffected
Figure 2-2. Control, Status, and Data Registers (Sheet 8 of 8)
MC68HC908GZ8
MOTOROLA
Data Sheet
Memory Map
For More Information On This Product,
Go to: www.freescale.com
39
Freescale Semiconductor, Inc.
Memory Map
.
Table 2-1. Vector Addresses
Vector Priority
Lowest
Vector
IF20
IF19
IF18
IF17
Freescale Semiconductor, Inc...
IF16
IF15
IF14
IF13
IF12
IF11
IF10
IF9
IF8
IF7
IF6
IF5
IF4
IF3
IF2
IF1
—
Highest
—
Address
$FFD4
$FFD5
$FFD6
$FFD7
$FFD8
$FFD9
$FFDA
$FFDB
$FFDC
$FFDD
$FFDE
$FFDF
$FFE0
$FFE1
$FFE2
$FFE3
$FFE4
$FFE5
$FFE6
$FFE7
$FFE8
$FFE9
$FFEA
$FFEB
$FFEC
$FFED
$FFEE
$FFEF
$FFF0
$FFF1
$FFF2
$FFF3
$FFF4
$FFF5
$FFF6
$FFF7
$FFF8
$FFF9
$FFFA
$FFFB
$FFFC
$FFFD
$FFFE
$FFFF
Vector
MSCAN08 Transmit Vector (High)
MSCAN08 Transmit Vector (Low)
MSCAN08 Receive Vector (High)
MSCAN08 Receive Vector (Low)
MSCAN08 Error Vector (High)
MSCAN08 Error Vector (Low)
MSCAN08 Wakeup Vector (High)
MSCAN08 Wakeup Vector (Low)
Timebase Vector (High)
Timebase Vector (Low)
ADC Conversion Complete Vector (High)
ADC Conversion Complete Vector (Low)
Keyboard Vector (High)
Keyboard Vector (Low)
ESCI Transmit Vector (High)
ESCI Transmit Vector (Low)
ESCI Receive Vector (High)
ESCI Receive Vector (Low)
ESCI Error Vector (High)
ESCI Error Vector (Low)
SPI Transmit Vector (High)
SPI Transmit Vector (Low)
SPI Receive Vector (High)
SPI Receive Vector (Low)
TIM2 Overflow Vector (High)
TIM2 Overflow Vector (Low)
TIM2 Channel 1 Vector (High)
TIM2 Channel 1 Vector (Low)
TIM2 Channel 0 Vector (High)
TIM2 Channel 0 Vector (Low)
TIM1 Overflow Vector (High)
TIM1 Overflow Vector (Low)
TIM1 Channel 1 Vector (High)
TIM1 Channel 1 Vector (Low)
TIM1 Channel 0 Vector (High)
TIM1 Channel 0 Vector (Low)
PLL Vector (High)
PLL Vector (Low)
IRQ Vector (High)
IRQ Vector (Low)
SWI Vector (High)
SWI Vector (Low)
Reset Vector (High)
Reset Vector (Low)
Data Sheet
40
MC68HC908GZ8
Memory Map
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 3. Low-Power Modes
Freescale Semiconductor, Inc...
3.1 Introduction
The microcontroller (MCU) may enter two low-power modes: wait mode and stop
mode. They are common to all HC08 MCUs and are entered through instruction
execution. This section describes how each module acts in the low-power modes.
3.1.1 Wait Mode
The WAIT instruction puts the MCU in a low-power standby mode in which the
central processor unit (CPU) clock is disabled but the bus clock continues to run.
Power consumption can be further reduced by disabling the low-voltage inhibit
(LVI) module through bits in the CONFIG1 register. See Section 8. Configuration
Register (CONFIG).
3.1.2 Stop Mode
Stop mode is entered when a STOP instruction is executed. The CPU clock is
disabled and the bus clock is disabled if the OSCENINSTOP bit in the CONFIG2
register is at a logic 0. See Section 8. Configuration Register (CONFIG).
3.2 Analog-to-Digital Converter (ADC)
3.2.1 Wait Mode
The analog-to-digital converter (ADC) continues normal operation during wait
mode. Any enabled CPU interrupt request from the ADC can bring the MCU out of
wait mode. If the ADC is not required to bring the MCU out of wait mode, power
down the ADC by setting ADCH4–ADCH0 bits in the ADC status and control
register before executing the WAIT instruction.
3.2.2 Stop Mode
The ADC module is inactive after the execution of a STOP instruction. Any pending
conversion is aborted. ADC conversions resume when the MCU exits stop mode
after an external interrupt. Allow one conversion cycle to stabilize the analog
circuitry.
MC68HC908GZ8
MOTOROLA
Data Sheet
Low-Power Modes
For More Information On This Product,
Go to: www.freescale.com
41
Freescale Semiconductor, Inc.
Low-Power Modes
3.3 Break Module (BRK)
3.3.1 Wait Mode
If enabled, the break (BRK) module is active in wait mode. In the break routine, the
user can subtract one from the return address on the stack if the SBSW bit in the
break status register is set.
3.3.2 Stop Mode
Freescale Semiconductor, Inc...
The break module is inactive in stop mode. The STOP instruction does not affect
break module register states.
3.4 Clock Generator Module (CGM)
3.4.1 Wait Mode
The clock generator module (CGM) remains active in wait mode. Before entering
wait mode, software can disengage and turn off the PLL by clearing the BCS and
PLLON bits in the PLL control register (PCTL). Less power-sensitive applications
can disengage the PLL without turning it off. Applications that require the PLL to
wake the MCU from wait mode also can deselect the PLL output without turning off
the PLL.
3.4.2 Stop Mode
If the OSCSTOPEN bit in the CONFIG register is cleared (default), then the STOP
instruction disables the CGM (oscillator and phase-locked loop) and holds low all
CGM outputs (CGMXCLK, CGMOUT, and CGMINT).
If the STOP instruction is executed with the VCO clock, CGMVCLK, divided by two
driving CGMOUT, the PLL automatically clears the BCS bit in the PLL control
register (PCTL), thereby selecting the crystal clock, CGMXCLK, divided by two as
the source of CGMOUT. When the MCU recovers from STOP, the crystal clock
divided by two drives CGMOUT and BCS remains clear.
If the OSCSTOPEN bit in the CONFIG register is set, then the phase locked loop
is shut off, but the oscillator will continue to operate in stop mode.
3.5 Computer Operating Properly Module (COP)
3.5.1 Wait Mode
The COP remains active during wait mode. If COP is enabled, a reset will occur at
COP timeout.
Data Sheet
42
MC68HC908GZ8
Low-Power Modes
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Low-Power Modes
Central Processor Unit (CPU)
3.5.2 Stop Mode
Stop mode turns off the COPCLK input to the COP and clears the COP prescaler.
Service the COP immediately before entering or after exiting stop mode to ensure
a full COP timeout period after entering or exiting stop mode.
The STOP bit in the CONFIG1 register enables the STOP instruction. To prevent
inadvertently turning off the COP with a STOP instruction, disable the STOP
instruction by clearing the STOP bit.
Freescale Semiconductor, Inc...
3.6 Central Processor Unit (CPU)
3.6.1 Wait Mode
The WAIT instruction:
•
Clears the interrupt mask (I bit) in the condition code register, enabling
interrupts. After exit from wait mode by interrupt, the I bit remains clear. After
exit by reset, the I bit is set.
•
Disables the CPU clock
3.6.2 Stop Mode
The STOP instruction:
•
Clears the interrupt mask (I bit) in the condition code register, enabling
external interrupts. After exit from stop mode by external interrupt, the I bit
remains clear. After exit by reset, the I bit is set.
•
Disables the CPU clock
After exiting stop mode, the CPU clock begins running after the oscillator
stabilization delay.
3.7 External Interrupt Module (IRQ)
3.7.1 Wait Mode
The external interrupt (IRQ) module remains active in wait mode. Clearing the
IMASK1 bit in the IRQ status and control register enables IRQ CPU interrupt
requests to bring the MCU out of wait mode.
3.7.2 Stop Mode
The IRQ module remains active in stop mode. Clearing the IMASK1 bit in the IRQ
status and control register enables IRQ CPU interrupt requests to bring the MCU
out of stop mode.
MC68HC908GZ8
MOTOROLA
Data Sheet
Low-Power Modes
For More Information On This Product,
Go to: www.freescale.com
43
Freescale Semiconductor, Inc.
Low-Power Modes
3.8 Keyboard Interrupt Module (KBI)
3.8.1 Wait Mode
The keyboard interrupt (KBI) module remains active in wait mode. Clearing the
IMASKK bit in the keyboard status and control register enables keyboard interrupt
requests to bring the MCU out of wait mode.
Freescale Semiconductor, Inc...
3.8.2 Stop Mode
The keyboard module remains active in stop mode. Clearing the IMASKK bit in the
keyboard status and control register enables keyboard interrupt requests to bring
the MCU out of stop mode.
3.9 Low-Voltage Inhibit Module (LVI)
3.9.1 Wait Mode
If enabled, the low-voltage inhibit (LVI) module remains active in wait mode. If
enabled to generate resets, the LVI module can generate a reset and bring the
MCU out of wait mode.
3.9.2 Stop Mode
If enabled, the LVI module remains active in stop mode. If enabled to generate
resets, the LVI module can generate a reset and bring the MCU out of stop mode.
3.10 Motorola Scalable Controller Area Network Module (MSCAN)
3.10.1 Wait Mode
The Motorola scalable controller area network (MSCAN) module remains active
after execution of the WAIT instruction. In wait mode, the MSCAN08 registers are
not accessible by the CPU.
If the MSCAN08 functions are not required during wait mode, reduce the power
consumption by disabling the MSCAN08 module before enabling the WAIT
instruction.
3.10.2 Stop Mode
The MSCAN08 module is inactive in stop mode. The STOP instruction does not
affect MSCAN08 register states.
Because the internal clock is inactive during stop mode, entering stop mode during
an MSCAN08 transmission or reception results in invalid data.
Data Sheet
44
MC68HC908GZ8
Low-Power Modes
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Low-Power Modes
Enhanced Serial Communications Interface Module (ESCI)
3.11 Enhanced Serial Communications Interface Module (ESCI)
3.11.1 Wait Mode
The enhanced serial communications interface (ESCI), or SCI module for short,
module remains active in wait mode. Any enabled CPU interrupt request from the
SCI module can bring the MCU out of wait mode.
If SCI module functions are not required during wait mode, reduce power
consumption by disabling the module before executing the WAIT instruction.
Freescale Semiconductor, Inc...
3.11.2 Stop Mode
The SCI module is inactive in stop mode. The STOP instruction does not affect SCI
register states. SCI module operation resumes after the MCU exits stop mode.
Because the internal clock is inactive during stop mode, entering stop mode during
an SCI transmission or reception results in invalid data.
3.12 Serial Peripheral Interface Module (SPI)
3.12.1 Wait Mode
The serial peripheral interface (SPI) module remains active in wait mode. Any
enabled CPU interrupt request from the SPI module can bring the MCU out of wait
mode.
If SPI module functions are not required during wait mode, reduce power
consumption by disabling the SPI module before executing the WAIT instruction.
3.12.2 Stop Mode
The SPI module is inactive in stop mode. The STOP instruction does not affect SPI
register states. SPI operation resumes after an external interrupt. If stop mode is
exited by reset, any transfer in progress is aborted, and the SPI is reset.
3.13 Timebase Module (TBM)
3.13.1 Wait Mode
The timebase module (TBM) remains active after execution of the WAIT
instruction. In wait mode, the timebase register is not accessible by the CPU.
If the timebase functions are not required during wait mode, reduce the power
consumption by stopping the timebase before enabling the WAIT instruction.
MC68HC908GZ8
MOTOROLA
Data Sheet
Low-Power Modes
For More Information On This Product,
Go to: www.freescale.com
45
Freescale Semiconductor, Inc.
Low-Power Modes
3.13.2 Stop Mode
The timebase module may remain active after execution of the STOP instruction if
the oscillator has been enabled to operate during stop mode through the
OSCENINSTOP bit in the CONFIG2 register. The timebase module can be used
in this mode to generate a periodic wakeup from stop mode.
Freescale Semiconductor, Inc...
If the oscillator has not been enabled to operate in stop mode, the timebase module
will not be active during stop mode. In stop mode, the timebase register is not
accessible by the CPU.
If the timebase functions are not required during stop mode, reduce the power
consumption by stopping the timebase before enabling the STOP instruction.
3.14 Timer Interface Module (TIM1 and TIM2)
3.14.1 Wait Mode
The timer interface modules (TIM) remain active in wait mode. Any enabled CPU
interrupt request from the TIM can bring the MCU out of wait mode.
If TIM functions are not required during wait mode, reduce power consumption by
stopping the TIM before executing the WAIT instruction.
3.14.2 Stop Mode
The TIM is inactive in stop mode. The STOP instruction does not affect register
states or the state of the TIM counter. TIM operation resumes when the MCU exits
stop mode after an external interrupt.
3.15 Exiting Wait Mode
These events restart the CPU clock and load the program counter with the reset
vector or with an interrupt vector:
•
External reset — A logic 0 on the RST pin resets the MCU and loads the
program counter with the contents of locations $FFFE and $FFFF.
•
External interrupt — A high-to-low transition on an external interrupt pin
(IRQ pin) loads the program counter with the contents of locations: $FFFA
and $FFFB; IRQ pin.
•
Break interrupt — In emulation mode, a break interrupt loads the program
counter with the contents of $FFFC and $FFFD.
•
Computer operating properly (COP) module reset — A timeout of the COP
counter resets the MCU and loads the program counter with the contents of
$FFFE and $FFFF.
Data Sheet
46
MC68HC908GZ8
Low-Power Modes
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Low-Power Modes
Exiting Wait Mode
•
Low-voltage inhibit (LVI) module reset — A power supply voltage below the
VTRIPF voltage resets the MCU and loads the program counter with the
contents of locations $FFFE and $FFFF.
•
Clock generator module (CGM) interrupt — A CPU interrupt request from
the ICG loads the program counter with the contents of $FFF8 and $FFF9.
•
Keyboard interrupt (KBI) module — A CPU interrupt request from the KBI
module loads the program counter with the contents of $FFE0 and $FFE1.
•
Timer 1 interface (TIM1) module interrupt — A CPU interrupt request from
the TIM1 loads the program counter with the contents of:
– $FFF2 and $FFF3; TIM1 overflow
– $FFF4 and $FFF5; TIM1 channel 1
– $FFF6 and $FFF7; TIM1 channel 0
•
Timer 2 interface (TIM2) module interrupt — A CPU interrupt request from
the TIM2 loads the program counter with the contents of:
– $FFEC and $FFED; TIM2 overflow
– $FFEE and $FFEF; TIM2 channel 1
– $FFF0 and $FFF1; TIM2 channel 0
•
Serial peripheral interface (SPI) module interrupt — A CPU interrupt request
from the SPI loads the program counter with the contents of:
– $FFE8 and $FFE9; SPI transmitter
– $FFEA and $FFEB; SPI receiver
•
Serial communications interface (SCI) module interrupt — A CPU interrupt
request from the SCI loads the program counter with the contents of:
– $FFE2 and $FFE3; SCI transmitter
– $FFE4 and $FFE5; SCI receiver
– $FFE6 and $FFE7; SCI receiver error
•
Analog-to-digital converter (ADC) module interrupt — A CPU interrupt
request from the ADC loads the program counter with the contents of:
$FFDE and $FFDF; ADC conversion complete.
•
Timebase module (TBM) interrupt — A CPU interrupt request from the TBM
loads the program counter with the contents of: $FFDC and $FFDD; TBM
interrupt.
•
Motorola scalable controller area network (MSCAN) module interrupt — A
CPU interrupt request from the MSCAN08 loads the program counter with
the contents of:
– $FFD4 and $FFD5; MSCAN08 transmitter
– $FFD6 and $FFD7; MSCAN08 receiver
– $FFD8 and $FFD9; MSCAN08 error
– $FFDA and $FFDB; MSCAN08 wakeup
MC68HC908GZ8
MOTOROLA
Data Sheet
Low-Power Modes
For More Information On This Product,
Go to: www.freescale.com
47
Freescale Semiconductor, Inc.
Low-Power Modes
3.16 Exiting Stop Mode
Freescale Semiconductor, Inc...
These events restart the system clocks and load the program counter with the reset
vector or with an interrupt vector:
•
External reset — A logic 0 on the RST pin resets the MCU and loads the
program counter with the contents of locations $FFFE and $FFFF.
•
External interrupt — A high-to-low transition on an external interrupt pin
loads the program counter with the contents of locations:
– $FFFA and $FFFB; IRQ pin
– $FFE0 and $FFE1; keyboard interrupt pins
•
Low-voltage inhibit (LVI) reset — A power supply voltage below the LVITRIPF
voltage resets the MCU and loads the program counter with the contents of
locations $FFFE and $FFFF.
•
Timebase module (TBM) interrupt — A TBM interrupt loads the program
counter with the contents of locations $FFDC and $FFDD when the
timebase counter has rolled over. This allows the TBM to generate a
periodic wakeup from stop mode.
•
MSCAN08 interrupt — MSCAN08 bus activity can wake the MCU from CPU
stop. However, until the oscillator starts up and synchronization is achieved
the MSCAN08 will not respond to incoming data.
Upon exit from stop mode, the system clocks begin running after an oscillator
stabilization delay. A 12-bit stop recovery counter inhibits the system clocks for
4096 CGMXCLK cycles after the reset or external interrupt.
The short stop recovery bit, SSREC, in the CONFIG1 register controls the oscillator
stabilization delay during stop recovery. Setting SSREC reduces stop recovery
time from 4096 CGMXCLK cycles to 32 CGMXCLK cycles.
NOTE:
Use the full stop recovery time (SSREC = 0) in applications that use an external
crystal.
Data Sheet
48
MC68HC908GZ8
Low-Power Modes
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 4. Resets and Interrupts
Freescale Semiconductor, Inc...
4.1 Introduction
Resets and interrupts are responses to exceptional events during program
execution. A reset re-initializes the microcontroller (MCU) to its startup condition.
An interrupt vectors the program counter to a service routine.
4.2 Resets
A reset immediately returns the MCU to a known startup condition and begins
program execution from a user-defined memory location.
4.2.1 Effects
A reset:
•
Immediately stops the operation of the instruction being executed
•
Initializes certain control and status bits
•
Loads the program counter with a user-defined reset vector address from
locations $FFFE and $FFFF
•
Selects CGMXCLK divided by four as the bus clock
4.2.2 External Reset
A logic 0 applied to the RST pin for a time, tRL, generates an external reset. An
external reset sets the PIN bit in the system integration module (SIM) reset status
register.
4.2.3 Internal Reset
Sources:
•
Power-on reset (POR)
•
Computer operating properly (COP)
•
Low-power reset circuits
•
Illegal opcode
•
Illegal address
MC68HC908GZ8
MOTOROLA
Data Sheet
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
49
Freescale Semiconductor, Inc.
Resets and Interrupts
All internal reset sources pull the RST pin low for 32 CGMXCLK cycles to allow
resetting of external devices. The MCU is held in reset for an additional 32
CGMXCLK cycles after releasing the RST pin.
4.2.3.1 Power-On Reset (POR)
A power-on reset (POR) is an internal reset caused by a positive transition on the
VDD pin. VDD at the POR must below VPOR to reset the MCU. This distinguishes
between a reset and a POR. The POR is not a brown-out detector, low-voltage
detector, or glitch detector.
Freescale Semiconductor, Inc...
A power-on reset:
•
Holds the clocks to the central processor unit (CPU) and modules inactive
for an oscillator stabilization delay of 4096 CGMXCLK cycles
•
Drives the RST pin low during the oscillator stabilization delay
•
Releases the RST pin 32 CGMXCLK cycles after the oscillator stabilization
delay
•
Releases the CPU to begin the reset vector sequence 64 CGMXCLK cycles
after the oscillator stabilization delay
•
Sets the POR and LVI bits in the SIM reset status register and clears all
other bits in the register
OSC1
PORRST(1)
4096
CYCLES
32
CYCLES
CGMXCLK
CGMOUT
RST PIN
1. PORRST is an internally generated power-on reset pulse.
Figure 4-1. Power-On Reset Recovery
4.2.3.2 Computer Operating Properly (COP) Reset
A computer operating properly (COP) reset is an internal reset caused by an
overflow of the COP counter. A COP reset sets the COP bit in the SIM reset status
register.
To clear the COP counter and prevent a COP reset, write any value to the COP
control register at location $FFFF.
Data Sheet
50
MC68HC908GZ8
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Resets and Interrupts
Resets
4.2.3.3 Low-Voltage Inhibit (LVI) Reset
A low-voltage inhibit (LVI) reset is an internal reset caused by a drop in the power
supply voltage to the LVITRIPF voltage.
Freescale Semiconductor, Inc...
An LVI reset:
•
Holds the clocks to the CPU and modules inactive for an oscillator
stabilization delay of 4096 CGMXCLK cycles after the power supply voltage
rises to the LVITRIPR voltage
•
Drives the RST pin low for as long as VDD is below the LVITRIPR voltage and
during the oscillator stabilization delay
•
Releases the RST pin 32 CGMXCLK cycles after the oscillator stabilization
delay
•
Releases the CPU to begin the reset vector sequence 64 CGMXCLK cycles
after the oscillator stabilization delay
•
Sets the LVI bit in the SIM reset status register
4.2.3.4 Illegal Opcode Reset
An illegal opcode reset is an internal reset caused by an opcode that is not in the
instruction set. An illegal opcode reset sets the ILOP bit in the SIM reset status
register.
If the stop enable bit, STOP, in the mask option register is a logic 0, the STOP
instruction causes an illegal opcode reset.
4.2.3.5 Illegal Address Reset
An illegal address reset is an internal reset caused by opcode fetch from an
unmapped address. An illegal address reset sets the ILAD bit in the SIM reset
status register.
A data fetch from an unmapped address does not generate a reset.
4.2.4 System Integration Module (SIM) Reset Status Register
This read-only register contains flags to show reset sources. All flag bits are
automatically cleared following a read of the register. Reset service can read the
SIM reset status register to clear the register after power-on reset and to determine
the source of any subsequent reset.
The register is initialized on power-up as shown with the POR bit set and all other
bits cleared. During a POR or any other internal reset, the RST pin is pulled low.
After the pin is released, it will be sampled 32 CGMXCLK cycles later. If the pin is
not above a VIH at that time, then the PIN bit in the SRSR may be set in addition to
whatever other bits are set.
MC68HC908GZ8
MOTOROLA
Data Sheet
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
51
Freescale Semiconductor, Inc.
Resets and Interrupts
NOTE:
Only a read of the SIM reset status register clears all reset flags. After multiple
resets from different sources without reading the register, multiple flags remain set.
Address:
Read:
$FE01
Bit 7
6
5
4
3
2
1
Bit 0
POR
PIN
COP
ILOP
ILAD
MODRST
LVI
0
0
0
0
0
0
0
0
Write:
POR:
1
= Unimplemented
Freescale Semiconductor, Inc...
Figure 4-2. SIM Reset Status Register (SRSR)
POR — Power-On Reset Flag
1 = Power-on reset since last read of SRSR
0 = Read of SRSR since last power-on reset
PIN — External Reset Flag
1 = External reset via RST pin since last read of SRSR
0 = POR or read of SRSR since last external reset
COP — Computer Operating Properly Reset Bit
1 = Last reset caused by timeout of COP counter
0 = POR or read of SRSR since any reset
ILOP — Illegal Opcode Reset Bit
1 = Last reset caused by an illegal opcode
0 = POR or read of SRSR since any reset
ILAD — Illegal Address Reset Bit
1 = Last reset caused by an opcode fetch from an illegal address
0 = POR or read of SRSR since any reset
MODRST — Monitor Mode Entry Module Reset Bit
1 = Last reset caused by forced monitor mode entry.
0 = POR or read of SRSR since any reset
LVI — Low-Voltage Inhibit Reset Bit
1 = Last reset caused by low-power supply voltage
0 = POR or read of SRSR since any reset
Data Sheet
52
MC68HC908GZ8
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Resets and Interrupts
Interrupts
4.3 Interrupts
An interrupt temporarily changes the sequence of program execution to respond to
a particular event. An interrupt does not stop the operation of the instruction being
executed, but begins when the current instruction completes its operation.
4.3.1 Effects
Freescale Semiconductor, Inc...
An interrupt:
•
Saves the CPU registers on the stack. At the end of the interrupt, the RTI
instruction recovers the CPU registers from the stack so that normal
processing can resume.
•
Sets the interrupt mask (I bit) to prevent additional interrupts. Once an
interrupt is latched, no other interrupt can take precedence, regardless of its
priority.
•
Loads the program counter with a user-defined vector address
•
•
•
CONDITION CODE REGISTER
1
4
ACCUMULATOR
2
3
INDEX REGISTER (LOW BYTE)(1)
3
2
PROGRAM COUNTER (HIGH BYTE)
4
1
PROGRAM COUNTER (LOW BYTE)
5
5
STACKING
ORDER
UNSTACKING
ORDER
•
•
•
$00FF DEFAULT ADDRESS ON RESET
1. High byte of index register is not stacked.
Figure 4-3. Interrupt Stacking Order
After every instruction, the CPU checks all pending interrupts if the I bit is not set.
If more than one interrupt is pending when an instruction is done, the highest
priority interrupt is serviced first. In the example shown in Figure 4-4, if an interrupt
is pending upon exit from the interrupt service routine, the pending interrupt is
serviced before the LDA instruction is executed.
MC68HC908GZ8
MOTOROLA
Data Sheet
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
53
Freescale Semiconductor, Inc.
Resets and Interrupts
CLI
BACKGROUND
ROUTINE
LDA #$FF
INT1
PSHH
INT1 INTERRUPT SERVICE ROUTINE
Freescale Semiconductor, Inc...
PULH
RTI
INT2
PSHH
INT2 INTERRUPT SERVICE ROUTINE
PULH
RTI
Figure 4-4. Interrupt Recognition Example
The LDA opcode is prefetched by both the INT1 and INT2 RTI instructions.
However, in the case of the INT1 RTI prefetch, this is a redundant operation.
NOTE:
To maintain compatibility with the M6805 Family, the H register is not pushed on
the stack during interrupt entry. If the interrupt service routine modifies the H
register or uses the indexed addressing mode, save the H register and then restore
it prior to exiting the routine.
See Figure 4-5 for a flowchart depicting interrupt processing.
4.3.2 Sources
The sources in Table 4-1 can generate CPU interrupt requests.
Data Sheet
54
MC68HC908GZ8
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Resets and Interrupts
Interrupts
FROM RESET
BREAK
INTERRUPT
?
NO
YES
YES
BITSET?
SET?
IIBIT
Freescale Semiconductor, Inc...
NO
IRQ
INTERRUPT
?
NO
YES
CGM
INTERRUPT
?
NO
YES
OTHER
INTERRUPTS
?
YES
NO
STACK CPU REGISTERS
SET I BIT
LOAD PC WITH INTERRUPT VECTOR
FETCH NEXT
INSTRUCTION
SWI
INSTRUCTION
?
YES
NO
RTI
INSTRUCTION
?
YES
UNSTACK CPU REGISTERS
NO
EXECUTE INSTRUCTION
Figure 4-5. Interrupt Processing
MC68HC908GZ8
MOTOROLA
Data Sheet
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
55
Freescale Semiconductor, Inc.
Resets and Interrupts
Table 4-1. Interrupt Sources
Flag
Mask(1)
INT Register
Flag
Priority(2)
Vector
Address
Reset
None
None
None
0
$FFFE–$FFFF
SWI instruction
None
None
None
0
$FFFC–$FFFD
IRQ pin
IRQF
IMASK1
IF1
1
$FFFA–$FFFB
Source
CGM change in lock
PLLF
PLLIE
IF2
2
$FFF8–$FFF9
TIM1 channel 0
CH0F
CH0IE
IF3
3
$FFF6–$FFF7
TIM1 channel 1
CH1F
CH1IE
IF4
4
$FFF4–$FFF5
TOF
TOIE
IF5
5
$FFF2–$FFF3
TIM2 channel 0
CH0F
CH0IE
IF6
6
$FFF0–$FFF1
TIM2 channel 1
CH1F
CH1IE
IF7
7
$FFEE–$FFEF
TOF
TOIE
IF8
8
$FFEC–$FFED
IF9
9
$FFEA–$FFEB
IF10
10
$FFE8–$FFE9
IF11
11
$FFE6–$FFE7
IF12
12
$FFE4–$FFE5
IF13
13
$FFE2–$FFE3
$FFE0–$FFE1
Freescale Semiconductor, Inc...
TIM1 overflow
TIM2 overflow
SPI receiver full
SPRF
SPRIE
SPI overflow
OVRF
ERRIE
SPI mode fault
MODF
ERRIE
SPI transmitter empty
SPTE
SPTIE
SCI receiver overrun
OR
ORIE
SCI noise flag
NF
NEIE
SCI framing error
FE
FEIE
SCI parity error
PE
PEIE
SCI receiver full
SCRF
SCRIE
SCI input idle
IDLE
ILIE
SCI transmitter empty
SCTE
SCTIE
TC
TCIE
Keyboard pin
KEYF
IMASKK
IF14
14
ADC conversion complete
COCO
AIEN
IF15
15
$FFDE–$FFDF
TBIF
TBIE
IF16
16
$FFDC–$FFDD
WUPIF
WUPIE
IF17
17
$FFDA–$FFDB
RWRNIF
TWRNIF
RERIF
TERRIF
BOFFIF
OVRIF
RWRNIE
TWRNIE
RERRIE
TERRIE
BOFFIE
OVRIE
IF18
18
$FFD8–$FFD9
SCI transmission complete
Timebase
MSCAN08 receiver wakeup
MSCAN08 error
MSCAN08 receiver
RXF
RXFIE
IF19
19
$FFD6–$FFD7
MSCAN08 transmitter
TXE2
TXE1
TXE0
TXEIE2
TXEIE1
TXEIE0
IF20
20
$FFD4–$FFD5
1. The I bit in the condition code register is a global mask for all interrupt sources except the SWI instruction.
2. 0 = highest priority
Data Sheet
56
MC68HC908GZ8
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Resets and Interrupts
Interrupts
4.3.2.1 Software Interrupt (SWI) Instruction
The software interrupt (SWI) instruction causes a non-maskable interrupt.
NOTE:
A software interrupt pushes PC onto the stack. An SWI does not push PC – 1, as
a hardware interrupt does.
4.3.2.2 Break Interrupt
Freescale Semiconductor, Inc...
The break module causes the CPU to execute an SWI instruction at a
software-programmable break point.
4.3.2.3 IRQ Pin
A logic 0 on the IRQ pin latches an external interrupt request.
4.3.2.4 Clock Generator (CGM)
The CGM can generate a CPU interrupt request every time the phase-locked loop
circuit (PLL) enters or leaves the locked state. When the LOCK bit changes state,
the PLL flag (PLLF) is set. The PLL interrupt enable bit (PLLIE) enables PLLF CPU
interrupt requests. LOCK is in the PLL bandwidth control register. PLLF is in the
PLL control register.
4.3.2.5 Timer Interface Module 1 (TIM1)
TIM1 CPU interrupt sources:
•
TIM1 overflow flag (TOF) — The TOF bit is set when the TIM1 counter value
rolls over to $0000 after matching the value in the TIM1 counter modulo
registers. The TIM1 overflow interrupt enable bit, TOIE, enables TIM1
overflow CPU interrupt requests. TOF and TOIE are in the TIM1 status and
control register.
•
TIM1 channel flags (CH1F–CH0F) — The CHxF bit is set when an input
capture or output compare occurs on channel x. The channel x interrupt
enable bit, CHxIE, enables channel x TIM1 CPU interrupt requests. CHxF
and CHxIE are in the TIM1 channel x status and control register.
4.3.2.6 Timer Interface Module 2 (TIM2)
TIM2 CPU interrupt sources:
•
TIM2 overflow flag (TOF) — The TOF bit is set when the TIM2 counter value
rolls over to $0000 after matching the value in the TIM2 counter modulo
registers. The TIM2 overflow interrupt enable bit, TOIE, enables TIM2
overflow CPU interrupt requests. TOF and TOIE are in the TIM2 status and
control register.
MC68HC908GZ8
MOTOROLA
Data Sheet
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
57
Freescale Semiconductor, Inc.
Resets and Interrupts
•
TIM2 channel flags (CH1F–CH0F) — The CHxF bit is set when an input
capture or output compare occurs on channel x. The channel x interrupt
enable bit, CHxIE, enables channel x TIM2 CPU interrupt requests. CHxF
and CHxIE are in the TIM2 channel x status and control register.
4.3.2.7 Serial Peripheral Interface (SPI)
Freescale Semiconductor, Inc...
SPI CPU interrupt sources:
•
SPI receiver full bit (SPRF) — The SPRF bit is set every time a byte
transfers from the shift register to the receive data register. The SPI receiver
interrupt enable bit, SPRIE, enables SPRF CPU interrupt requests. SPRF is
in the SPI status and control register and SPRIE is in the SPI control
register.
•
SPI transmitter empty (SPTE) — The SPTE bit is set every time a byte
transfers from the transmit data register to the shift register. The SPI
transmit interrupt enable bit, SPTIE, enables SPTE CPU interrupt requests.
SPTE is in the SPI status and control register and SPTIE is in the SPI control
register.
•
Mode fault bit (MODF) — The MODF bit is set in a slave SPI if the SS pin
goes high during a transmission with the mode fault enable bit (MODFEN)
set. In a master SPI, the MODF bit is set if the SS pin goes low at any time
with the MODFEN bit set. The error interrupt enable bit, ERRIE, enables
MODF CPU interrupt requests. MODF, MODFEN, and ERRIE are in the SPI
status and control register.
•
Overflow bit (OVRF) — The OVRF bit is set if software does not read the
byte in the receive data register before the next full byte enters the shift
register. The error interrupt enable bit, ERRIE, enables OVRF CPU interrupt
requests. OVRF and ERRIE are in the SPI status and control register.
4.3.2.8 Serial Communications Interface (SCI)
SCI CPU interrupt sources:
•
SCI transmitter empty bit (SCTE) — SCTE is set when the SCI data register
transfers a character to the transmit shift register. The SCI transmit interrupt
enable bit, SCTIE, enables transmitter CPU interrupt requests. SCTE is in
SCI status register 1. SCTIE is in SCI control register 2.
•
Transmission complete bit (TC) — TC is set when the transmit shift register
and the SCI data register are empty and no break or idle character has been
generated. The transmission complete interrupt enable bit, TCIE, enables
transmitter CPU interrupt requests. TC is in SCI status register 1. TCIE is in
SCI control register 2.
•
SCI receiver full bit (SCRF) — SCRF is set when the receive shift register
transfers a character to the SCI data register. The SCI receive interrupt
enable bit, SCRIE, enables receiver CPU interrupts. SCRF is in SCI status
register 1. SCRIE is in SCI control register 2.
Data Sheet
58
MC68HC908GZ8
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Resets and Interrupts
Interrupts
•
Idle input bit (IDLE) — IDLE is set when 10 or 11 consecutive logic 1s shift
in from the RxD pin. The idle line interrupt enable bit, ILIE, enables IDLE
CPU interrupt requests. IDLE is in SCI status register 1. ILIE is in SCI control
register 2.
•
Receiver overrun bit (OR) — OR is set when the receive shift register shifts
in a new character before the previous character was read from the SCI data
register. The overrun interrupt enable bit, ORIE, enables OR to generate
SCI error CPU interrupt requests. OR is in SCI status register 1. ORIE is in
SCI control register 3.
•
Noise flag (NF) — NF is set when the SCI detects noise on incoming data
or break characters, including start, data, and stop bits. The noise error
interrupt enable bit, NEIE, enables NF to generate SCI error CPU interrupt
requests. NF is in SCI status register 1. NEIE is in SCI control register 3.
•
Framing error bit (FE) — FE is set when a logic 0 occurs where the receiver
expects a stop bit. The framing error interrupt enable bit, FEIE, enables FE
to generate SCI error CPU interrupt requests. FE is in SCI status register 1.
FEIE is in SCI control register 3.
•
Parity error bit (PE) — PE is set when the SCI detects a parity error in
incoming data. The parity error interrupt enable bit, PEIE, enables PE to
generate SCI error CPU interrupt requests. PE is in SCI status register 1.
PEIE is in SCI control register 3.
4.3.2.9 KBD0–KBD7 Pins
A logic 0 on a keyboard interrupt pin latches an external interrupt request.
4.3.2.10 Analog-to-Digital Converter (ADC)
When the AIEN bit is set, the ADC module is capable of generating a CPU interrupt
after each ADC conversion. The COCO bit is not used as a conversion complete
flag when interrupts are enabled.
4.3.2.11 Timebase Module (TBM)
The timebase module can interrupt the CPU on a regular basis with a rate defined
by TBR2–TBR0. When the timebase counter chain rolls over, the TBIF flag is set.
If the TBIE bit is set, enabling the timebase interrupt, the counter chain overflow will
generate a CPU interrupt request.
Interrupts must be acknowledged by writing a logic 1 to the TACK bit.
MC68HC908GZ8
MOTOROLA
Data Sheet
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
59
Freescale Semiconductor, Inc.
Resets and Interrupts
4.3.2.12 Motorola Scalable Controller Area Network Module (MSCAN)
Freescale Semiconductor, Inc...
MSCAN08 interrupt sources:
•
MSCAN08 transmitter empty bits (TXE0–TXE2) — The TXEx bit is set when
the corresponding MSCAN08 data buffer is empty. The MSCAN08 transmit
interrupt enable bits, TXEIE0–TXEIE2, enables transmitter CPU interrupt
requests. TXEx is in MSCAN08 transmitter flag register. TXEIEx is in
MSCAN08 transmitter control register.
•
MSCAN08 receiver full bit (RXF) — The RXF bit is set when the a MSCAN08
message has been successfully received and loaded into the foreground
receive buffer. The MSCAN08 receive interrupt enable bit, RXFIE, enables
receiver CPU interrupt requests. RXF is in MSCAN08 receiver flag register.
RXFIE is in MSCAN08 receiver interrupt enable register.
•
MSCAN08 wakeup bit (WUPIF) — WUPIF is set when activity on the CAN
bus occurred during the MSCAN08 internal sleep mode. The wakeup
interrupt enable bit, WUPIE, enables MSCAN08 wakeup CPU interrupt
requests. WUPIF is in MSCAN08 receiver flag register. WUPIE is in
MSCAN08 receiver interrupt enable register.
•
Overrun bit (OVRIF) — OVRIF is set when both the foreground and the
background receive message buffers are filled with correctly received
messages and a further message is being received from the bus. The
overrun interrupt enable bit, OVRIE, enables OVRIF to generate MSCAN08
error CPU interrupt requests. OVRIF is in MSCAN08 receiver flag register.
OVRIE is in MSCAN08 receiver interrupt enable register.
•
Receiver Warning bit (RWRNIF) — RWRNIF is set when the receive error
counter has reached the CPU warning limit of 96. The receiver warning
interrupt enable bit, RWRNIE, enables RWRNIF to generate MSCAN08
error CPU interrupt requests. RWRNIF is in MSCAN08 receiver flag register.
RWRNIE is in MSCAN08 receiver interrupt enable register.
•
Transmitter Warning bit (TWRNIF) — TWRNIF is set when the transmit error
counter has reached the CPU warning limit of 96. The transmitter warning
interrupt enable bit, TWRNIF, enables TWRNIF to generate MSCAN08 error
CPU interrupt requests. TWRNIF is in MSCAN08 receiver flag register.
TWRNIE is in MSCAN08 receiver interrupt enable register.
•
Receiver Error Passive bit (RERRIF) — RERRIF is set when the receive
error counter has exceeded the error passive limit of 127 and the MSCAN08
has gone to error passive state. The receiver error passive interrupt enable
bit, RERRIE, enables RERRIF to generate MSCAN08 error CPU interrupt
requests. RERRIF is in MSCAN08 receiver flag register. RERRIE is in
MSCAN08 receiver interrupt enable register.
•
Transmitter Error Passive bit (TERRIF) — TERRIF is set when the transmit
error counter has exceeded the error passive limit of 127 and the MSCAN08
has gone to error passive state. The transmit error passive interrupt enable
bit, TERRIE, enables TERRIF to generate MSCAN08 error CPU interrupt
Data Sheet
60
MC68HC908GZ8
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Resets and Interrupts
Interrupts
requests. TERRIF is in MSCAN08 receiver flag register. TERRIE is in
MSCAN08 receiver interrupt enable register.
•
Bus Off bit (BOFFIF) — BOFFIF is set when the transmit error counter has
exceeded 255 and MSCAN08 has gone to bus off state. The bus off interrupt
enable bit, BOFFIE, enables BOFFIF to generate MSCAN08 error CPU
interrupt requests. BOFFIF is in MSCAN08 receiver flag register. BOFFIE is
in MSCAN08 receiver interrupt enable register.
4.3.3 Interrupt Status Registers
Freescale Semiconductor, Inc...
The flags in the interrupt status registers identify maskable interrupt sources. Table
4-2 summarizes the interrupt sources and the interrupt status register flags that
they set. The interrupt status registers can be useful for debugging.
Table 4-2. Interrupt Source Flags
Interrupt
Source
Interrupt Status
Register Flag
Reset
—
SWI instruction
—
IRQ pin
IF1
CGM change of lock
IF2
TIM1 channel 0
IF3
TIM1 channel 1
IF4
TIM1 overflow
IF5
TIM2 channel 0
IF6
TIM2 channel 1
IF7
TIM2 overflow
IF8
SPI receive
IF9
SPI transmit
IF10
SCI error
IF11
SCI receive
IF12
SCI transmit
IF13
Keyboard
IF14
ADC conversion complete
IF15
Timebase
IF16
MSCAN08 wakeup
IF17
MSCAN08 error
IF18
MSCAN08 receive
IF19
MSCAN08 transmit
IF20
MC68HC908GZ8
MOTOROLA
Data Sheet
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
61
Freescale Semiconductor, Inc.
Resets and Interrupts
4.3.3.1 Interrupt Status Register 1
Address:
$FE04
Bit 7
6
5
4
3
2
1
Bit 0
Read:
IF6
IF5
IF4
IF3
IF2
IF1
0
0
Write:
R
R
R
R
R
R
R
R
Reset:
0
0
0
0
0
0
0
0
R
= Reserved
Freescale Semiconductor, Inc...
Figure 4-6. Interrupt Status Register 1 (INT1)
IF6–IF1 — Interrupt Flags 6–1
These flags indicate the presence of interrupt requests from the sources shown
in Table 4-2.
1 = Interrupt request present
0 = No interrupt request present
Bit 1 and Bit 0 — Always read 0
4.3.3.2 Interrupt Status Register 2
Address:
$FE05
Bit 7
6
5
4
3
2
1
Bit 0
Read:
IF14
IF13
IF12
IF11
IF10
IF9
IF8
IF7
Write:
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
R
= Reserved
Reset:
Figure 4-7. Interrupt Status Register 2 (INT2)
IF14–IF7 — Interrupt Flags 14–7
These flags indicate the presence of interrupt requests from the sources shown
in Table 4-2.
1 = Interrupt request present
0 = No interrupt request present
Data Sheet
62
MC68HC908GZ8
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Resets and Interrupts
Interrupts
4.3.3.3 Interrupt Status Register 3
Address:
$FE06
Bit 7
6
5
4
3
2
1
Bit 0
Read:
0
0
IF20
IF19
IF18
IF17
IF16
IF15
Write:
R
R
R
R
R
R
R
R
Reset:
0
0
0
0
0
0
0
0
R
= Reserved
Figure 4-8. Interrupt Status Register 3 (INT3)
Freescale Semiconductor, Inc...
IF20–IF15 — Interrupt Flags 20–15
This flag indicates the presence of an interrupt request from the source shown
in Table 4-2.
1 = Interrupt request present
0 = No interrupt request present
Bits 7–6 — Always read 0
MC68HC908GZ8
MOTOROLA
Data Sheet
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
63
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Resets and Interrupts
Data Sheet
64
MC68HC908GZ8
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 5. Analog-to-Digital Converter (ADC)
5.1 Introduction
Freescale Semiconductor, Inc...
This section describes the 10-bit analog-to-digital converter (ADC).
5.2 Features
Features of the ADC module include:
•
Eight channels with multiplexed input
•
Linear successive approximation with monotonicity
•
10-bit resolution
•
Single or continuous conversion
•
Conversion complete flag or conversion complete interrupt
•
Selectable ADC clock
•
Left or right justified result
•
Left justified sign data mode
5.3 Functional Description
The ADC provides eight pins for sampling external sources at pins
PTB7/KBD7–PTB0/KBD0. An analog multiplexer allows the single ADC converter
to select one of eight ADC channels as ADC voltage in (VADIN). VADIN is converted
by the successive approximation register-based analog-to-digital converter. When
the conversion is completed, ADC places the result in the ADC data register and
sets a flag or generates an interrupt. See Figure 5-1.
5.3.1 ADC Port I/O Pins
PTB7/AD7–PTB0/AD0 are general-purpose I/O (input/output) pins that share with
the ADC channels. The channel select bits define which ADC channel/port pin will
be used as the input signal. The ADC overrides the port I/O logic by forcing that pin
as input to the ADC. The remaining ADC channels/port pins are controlled by the
port I/O logic and can be used as general-purpose I/O. Writes to the port register
or data direction register (DDR) will not have any affect on the port pin that is
selected by the ADC. Read of a port pin in use by the ADC will return a logic 0.
MC68HC908GZ8
MOTOROLA
Data Sheet
Analog-to-Digital Converter (ADC)
For More Information On This Product,
Go to: www.freescale.com
65
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
INTERNAL
DATA BUS
READ DDRBx
WRITE DDRBx
DISABLE
DDRBx
RESET
WRITE PTBx
PTBx
PTBx
ADC CHANNEL x
Freescale Semiconductor, Inc...
READ PTBx
DISABLE
ADC DATA REGISTER
INTERRUPT
LOGIC
AIEN
CONVERSION
COMPLETE
ADC
ADC
VOLTAGE IN
(VADIN)
CHANNEL
SELECT
ADCH4–ADCH0
ADC CLOCK
COCO
CGMXCLK
BUS CLOCK
CLOCK
GENERATOR
ADIV2–ADIV0
ADICLK
Figure 5-1. ADC Block Diagram
5.3.2 Voltage Conversion
When the input voltage to the ADC equals VREFH, the ADC converts the signal to
$3FF (full scale). If the input voltage equals VREFL, the ADC converts it to $000.
Input voltages between VREFH and VREFL are a straight-line linear conversion.
NOTE:
The ADC input voltage must always be greater than VSSAD and less than VDDAD.
Connect the VDDAD pin to the same voltage potential as the VDD pin, and connect
the VSSAD pin to the same voltage potential as the VSS pin.
The VDDAD pin should be routed carefully for maximum noise immunity.
Data Sheet
66
MC68HC908GZ8
Analog-to-Digital Converter (ADC)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
Functional Description
5.3.3 Conversion Time
Conversion starts after a write to the ADC status and control register (ADSCR).
One conversion will take between 16 and 17 ADC clock cycles. The ADIVx and
ADICLK bits should be set to provide a 1-MHz ADC clock frequency.
Conversion time =
16 to 17 ADC cycles
ADC frequency
Number of bus cycles = conversion time × bus frequency
Freescale Semiconductor, Inc...
5.3.4 Conversion
In continuous conversion mode, the ADC data register will be filled with new data
after each conversion. Data from the previous conversion will be overwritten
whether that data has been read or not. Conversions will continue until the ADCO
bit is cleared. The COCO bit is set after each conversion and will stay set until the
next read of the ADC data register.
In single conversion mode, conversion begins with a write to the ADSCR. Only one
conversion occurs between writes to the ADSCR.
When a conversion is in process and the ADCSCR is written, the current
conversion data should be discarded to prevent an incorrect reading.
5.3.5 Accuracy and Precision
The conversion process is monotonic and has no missing codes.
5.3.6 Result Justification
The conversion result may be formatted in four different ways:
1. Left justified
2. Right justified
3. Left Justified sign data mode
4. 8-bit truncation mode
All four of these modes are controlled using MODE0 and MODE1 bits located in
the ADC clock register (ADCLK).
Left justification will place the eight most significant bits (MSB) in the corresponding
ADC data register high, ADRH. This may be useful if the result is to be treated as
an 8-bit result where the two least significant bits (LSB), located in the ADC data
register low, ADRL, can be ignored. However, ADRL must be read after ADRH or
else the interlocking will prevent all new conversions from being stored.
MC68HC908GZ8
MOTOROLA
Data Sheet
Analog-to-Digital Converter (ADC)
For More Information On This Product,
Go to: www.freescale.com
67
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
Right justification will place only the two MSBs in the corresponding ADC data
register high, ADRH, and the eight LSBs in ADC data register low, ADRL. This
mode of operation typically is used when a 10-bit unsigned result is desired.
Left justified sign data mode is similar to left justified mode with one exception. The
MSB of the 10-bit result, AD9 located in ADRH, is complemented. This mode of
operation is useful when a result, represented as a signed magnitude from
mid-scale, is needed. Finally, 8-bit truncation mode will place the eight MSBs in the
ADC data register low, ADRL. The two LSBs are dropped. This mode of operation
is used when compatibility with 8-bit ADC designs are required. No interlocking
between ADRH and ADRL is present.
Freescale Semiconductor, Inc...
NOTE:
Quantization error is affected when only the most significant eight bits are used as
a result. See Figure 5-2.
8-BIT 10-BIT
RESULT RESULT
IDEAL 8-BIT CHARACTERISTIC
WITH QUANTIZATION = ±1/2
10-BIT TRUNCATED
TO 8-BIT RESULT
003
00B
00A
009
002
IDEAL 10-BIT CHARACTERISTIC
WITH QUANTIZATION = ±1/2
008
007
006
005
001
004
WHEN TRUNCATION IS USED,
ERROR FROM IDEAL 8-BIT = 3/8 LSB
DUE TO NON-IDEAL QUANTIZATION.
003
002
001
000
000
1/2
2 1/2
1 1/2
1/2
4 1/2
3 1/2
6 1/2
5 1/2
8 1/2
7 1/2
1 1/2
9 1/2
2 1/2
INPUT VOLTAGE
REPRESENTED AS 10-BIT
INPUT VOLTAGE
REPRESENTED AS 8-BIT
Figure 5-2. Bit Truncation Mode Error
Data Sheet
68
MC68HC908GZ8
Analog-to-Digital Converter (ADC)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
Monotonicity
5.4 Monotonicity
The conversion process is monotonic and has no missing codes.
5.5 Interrupts
Freescale Semiconductor, Inc...
When the AIEN bit is set, the ADC module is capable of generating CPU interrupts
after each ADC conversion. A CPU interrupt is generated if the COCO bit is at logic
0. The COCO bit is not used as a conversion complete flag when interrupts are
enabled.
5.6 Low-Power Modes
The WAIT and STOP instruction can put the MCU in low power- consumption
standby modes.
5.6.1 Wait Mode
The ADC continues normal operation during wait mode. Any enabled CPU interrupt
request from the ADC can bring the MCU out of wait mode. If the ADC is not
required to bring the MCU out of wait mode, power down the ADC by setting
ADCH4–ADCH0 bits in the ADC status and control register before executing the
WAIT instruction.
5.6.2 Stop Mode
The ADC module is inactive after the execution of a STOP instruction. Any pending
conversion is aborted. ADC conversions resume when the MCU exits stop mode
after an external interrupt. Allow one conversion cycle to stabilize the analog
circuitry.
5.7 I/O Signals
The ADC module has eight pins shared with port B, PTB7/AD7–PTB0/AD0.
5.7.1 ADC Analog Power Pin (VDDAD)
The ADC analog portion uses VDDAD as its power pin. Connect the VDDAD pin to
the same voltage potential as VDD. External filtering may be necessary to ensure
clean VDDAD for good results.
NOTE:
For maximum noise immunity, route VDDAD carefully and place bypass capacitors
as close as possible to the package.
VDDAD and VREFH are double-bonded on the MC68HC908GZ8.
MC68HC908GZ8
MOTOROLA
Data Sheet
Analog-to-Digital Converter (ADC)
For More Information On This Product,
Go to: www.freescale.com
69
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
5.7.2 ADC Analog Ground Pin (VSSAD)
The ADC analog portion uses VSSAD as its ground pin. Connect the VSSAD pin to
the same voltage potential as VSS.
NOTE:
Route VSSAD cleanly to avoid any offset errors.
VSSAD and VREFL are double-bonded on the MC68HC908GZ8.
Freescale Semiconductor, Inc...
5.7.3 ADC Voltage Reference High Pin (VREFH)
The ADC analog portion uses VREFH as its upper voltage reference pin. By default,
connect the VREFH pin to the same voltage potential as VDD. External filtering is
often necessary to ensure a clean VREFH for good results. Any noise present on
this pin will be reflected and possibly magnified in A/D conversion values.
NOTE:
For maximum noise immunity, route VREFH carefully and place bypass capacitors
as close as possible to the package. Routing VREFH close and parallel to VREFL
may improve common mode noise rejection.
VDDAD and VREFH are double-bonded on the MC68HC908GZ8.
5.7.4 ADC Voltage Reference Low Pin (VREFL)
The ADC analog portion uses VREFL as its lower voltage reference pin. By default,
connect the VREFH pin to the same voltage potential as VSS. External filtering is
often necessary to ensure a clean VREFL for good results. Any noise present on this
pin will be reflected and possibly magnified in A/D conversion values.
NOTE:
For maximum noise immunity, route VREFL carefully and, if not connected to VSS,
place bypass capacitors as close as possible to the package. Routing VREFH close
and parallel to VREFL may improve common mode noise rejection.
VSSAD and VREFL are double-bonded on the MC68HC908GZ8.
5.7.5 ADC Voltage In (VADIN)
VADIN is the input voltage signal from one of the eight ADC channels to the ADC
module.
Data Sheet
70
MC68HC908GZ8
Analog-to-Digital Converter (ADC)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
I/O Registers
5.8 I/O Registers
These I/O registers control and monitor ADC operation:
•
ADC status and control register (ADSCR)
•
ADC data register (ADRH and ADRL)
•
ADC clock register (ADCLK)
5.8.1 ADC Status and Control Register
Function of the ADC status and control register (ADSCR) is described here.
Freescale Semiconductor, Inc...
Address:
Read:
Write:
Reset:
$003C
Bit 7
6
5
4
3
2
1
Bit 0
COCO
AIEN
ADCO
ADCH4
ADCH3
ADCH2
ADCH1
ADCH0
0
0
0
1
1
1
1
1
Figure 5-3. ADC Status and Control Register (ADSCR)
COCO — Conversions Complete Bit
In non-interrupt mode (AIEN = 0), COCO is a read-only bit that is set at the end
of each conversion. COCO will stay set until cleared by a read of the ADC data
register. Reset clears this bit.
In interrupt mode (AIEN = 1), COCO is a read-only bit that is not set at the end
of a conversion. It always reads as a logic 0.
1 = Conversion completed (AIEN = 0)
0 = Conversion not completed (AIEN = 0) or CPU interrupt enabled
(AIEN = 1)
AIEN — ADC Interrupt Enable Bit
When this bit is set, an interrupt is generated at the end of an ADC conversion.
The interrupt signal is cleared when the data register is read or the status/control
register is written. Reset clears the AIEN bit.
1 = ADC interrupt enabled
0 = ADC interrupt disabled
ADCO — ADC Continuous Conversion Bit
When set, the ADC will convert samples continuously and update the ADR
register at the end of each conversion. Only one conversion is completed
between writes to the ADSCR when this bit is cleared. Reset clears the ADCO
bit.
1 = Continuous ADC conversion
0 = One ADC conversion
MC68HC908GZ8
MOTOROLA
Data Sheet
Analog-to-Digital Converter (ADC)
For More Information On This Product,
Go to: www.freescale.com
71
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
ADCH4–ADCH0 — ADC Channel Select Bits
ADCH4–ADCH0 form a 5-bit field which is used to select one of 16 ADC
channels. Only eight channels, AD7–AD0, are available on this MCU. The
channels are detailed in Table 5-1. Care should be taken when using a port pin
as both an analog and digital input simultaneously to prevent switching noise
from corrupting the analog signal. See Table 5-1.
The ADC subsystem is turned off when the channel select bits are all set to 1.
This feature allows for reduced power consumption for the MCU when the ADC
is not being used.
NOTE:
Recovery from the disabled state requires one conversion cycle to stabilize.
Freescale Semiconductor, Inc...
The voltage levels supplied from internal reference nodes, as specified in
Table 5-1, are used to verify the operation of the ADC converter both in production
test and for user applications.
Table 5-1. Mux Channel Select(1)
ADCH4
ADCH3
ADCH2
ADCH1
ADCH0
Input Select
0
0
0
0
0
PTB0/AD0
0
0
0
0
1
PTB1/AD1
0
0
0
1
0
PTB2/AD2
0
0
0
1
1
PTB3/AD3
0
0
1
0
0
PTB4/AD4
0
0
1
0
1
PTB5/AD5
0
0
1
1
0
PTB6/AD6
0
0
1
1
1
PTB7/AD7
0
1
0
0
0
↓
↓
↓
↓
↓
1
1
1
0
0
1
1
1
0
1
VREFH
1
1
1
1
0
VREFL
1
1
1
1
1
ADC power off
Unused
1. If any unused channels are selected, the resulting ADC conversion will be unknown or reserved.
Data Sheet
72
MC68HC908GZ8
Analog-to-Digital Converter (ADC)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
I/O Registers
5.8.2 ADC Data Register High and Data Register Low
5.8.2.1 Left Justified Mode
Freescale Semiconductor, Inc...
In left justified mode, the ADRH register holds the eight MSBs of the
10-bit result. The only difference from left justified mode is that the AD9 is
complemented. The ADRL register holds the two LSBs of the 10-bit result. All other
bits read as 0. ADRH and ADRL are updated each time an ADC single channel
conversion completes. Reading ADRH latches the contents of ADRL until ADRL is
read. All subsequent results will be lost until the ADRH and ADRL reads are
completed.
Address:
Read:
$003D
ADRH
Bit 7
6
5
4
3
2
1
Bit 0
AD9
AD8
AD7
AD6
AD5
AD4
AD3
AD2
Write:
Reset:
Address:
Read:
Unaffected by reset
$003E
AD1
ADRL
AD0
0
0
0
0
0
0
Write:
Reset:
Unaffected by reset
= Unimplemented
Figure 5-4. ADC Data Register High (ADRH) and Low (ADRL)
5.8.2.2 Right Justified Mode
In right justified mode, the ADRH register holds the two MSBs of the
10-bit result. All other bits read as 0. The ADRL register holds the eight LSBs of the
10-bit result. ADRH and ADRL are updated each time an ADC single channel
conversion completes. Reading ADRH latches the contents of ADRL until ADRL is
read. All subsequent results will be lost until the ADRH and ADRL reads are
completed.
Address:
Read:
$003D
ADRH
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
AD9
AD8
Write:
Reset:
Address:
Read:
Unaffected by reset
$003E
AD7
ADRL
AD6
AD5
AD4
AD3
AD2
AD1
AD0
Write:
Reset:
Unaffected by reset
= Unimplemented
Figure 5-5. ADC Data Register High (ADRH) and Low (ADRL)
MC68HC908GZ8
MOTOROLA
Data Sheet
Analog-to-Digital Converter (ADC)
For More Information On This Product,
Go to: www.freescale.com
73
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
5.8.2.3 Left Justified Signed Data Mode
In left justified signed data mode, the ADRH register holds the eight MSBs of the
10-bit result. The only difference from left justified mode is that the AD9 is
complemented. The ADRL register holds the two LSBs of the 10-bit result. All other
bits read as 0. ADRH and ADRL are updated each time an ADC single channel
conversion completes. Reading ADRH latches the contents of ADRL until ADRL is
read. All subsequent results will be lost until the ADRH and ADRL reads are
completed.
Freescale Semiconductor, Inc...
Address:
Read:
$003D
Bit 7
6
5
4
3
2
1
Bit 0
AD9
AD8
AD7
AD6
AD5
AD4
AD3
AD2
0
0
0
Write:
Reset:
Address:
Read:
Unaffected by reset
$003E
AD1
AD0
0
0
0
Write:
Reset:
Unaffected by reset
= Unimplemented
Figure 5-6. ADC Data Register High (ADRH) and Low (ADRL)
5.8.2.4 Eight Bit Truncation Mode
In 8-bit truncation mode, the ADRL register holds the eight MSBs of the 10-bit
result. The ADRH register is unused and reads as 0. The ADRL register is updated
each time an ADC single channel conversion completes. In 8-bit mode, the ADRL
register contains no interlocking with ADRH.
Address:
Read:
$003D
ADRH
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
Write:
Reset:
Address:
Read:
Unaffected by reset
$003E
AD9
ADRL
AD8
AD7
AD6
AD5
AD4
AD3
AD2
Write:
Reset:
Unaffected by reset
= Unimplemented
Figure 5-7. ADC Data Register High (ADRH) and Low (ADRL)
Data Sheet
74
MC68HC908GZ8
Analog-to-Digital Converter (ADC)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
I/O Registers
5.8.3 ADC Clock Register
The ADC clock register (ADCLK) selects the clock frequency for the ADC.
Address:
Read:
Write:
Reset:
$003F
Bit 7
6
5
4
3
2
1
ADIV2
ADIV1
ADIV0
ADICLK
MODE1
MODE0
R
0
0
0
0
0
1
0
R
= Reserved
= Unimplemented
Bit 0
0
0
Freescale Semiconductor, Inc...
Figure 5-8. ADC Clock Register (ADCLK)
ADIV2–ADIV0 — ADC Clock Prescaler Bits
ADIV2–ADIV0 form a 3-bit field which selects the divide ratio used by the ADC
to generate the internal ADC clock. Table 5-2 shows the available clock
configurations. The ADC clock should be set to approximately 1 MHz.
Table 5-2. ADC Clock Divide Ratio
ADIV2
ADIV1
ADIV0
ADC Clock Rate
0
0
0
ADC input clock ÷ 1
0
0
1
ADC input clock ÷ 2
0
1
0
ADC input clock ÷ 4
0
1
1
ADC input clock ÷ 8
1
X(1)
X(1)
ADC input clock ÷ 16
1. X = Don’t care
ADICLK — ADC Input Clock Select Bit
ADICLK selects either the bus clock or the oscillator output clock (CGMXCLK)
as the input clock source to generate the internal ADC clock. Reset selects
CGMXCLK as the ADC clock source.
1 = Internal bus clock
0 = Oscillator output clock (CGMXCLK)
The ADC requires a clock rate of approximately 1 MHz for correct operation. If the
selected clock source is not fast enough, the ADC will generate incorrect
conversions. See 24.10 5.0-Volt ADC Characteristics.
fADIC =
fCGMXCLK or bus frequency
ADIV[2:0]
MC68HC908GZ8
MOTOROLA
≅ 1 MHz
Data Sheet
Analog-to-Digital Converter (ADC)
For More Information On This Product,
Go to: www.freescale.com
75
Freescale Semiconductor, Inc.
Analog-to-Digital Converter (ADC)
Freescale Semiconductor, Inc...
MODE1 and MODE0 — Modes of Result Justification Bits
MODE1 and MODE0 select among four modes of operation. The manner in
which the ADC conversion results will be placed in the ADC data registers is
controlled by these modes of operation. Reset returns right-justified mode.
00 = 8-bit truncation mode
01 = Right justified mode
10 = Left justified mode
11 = Left justified signed data mode
Data Sheet
76
MC68HC908GZ8
Analog-to-Digital Converter (ADC)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 6. Break Module (BRK)
Freescale Semiconductor, Inc...
6.1 Introduction
This section describes the break module. The break module can generate a break
interrupt that stops normal program flow at a defined address to enter a
background program.
6.2 Features
Features of the break module include:
•
Accessible input/output (I/O) registers during the break Interrupt
•
Central processor unit (CPU) generated break interrupts
•
Software-generated break interrupts
•
Computer operating properly (COP) disabling during break interrupts
6.3 Functional Description
When the internal address bus matches the value written in the break address
registers, the break module issues a breakpoint signal (BKPT) to the system
integration module (SIM). The SIM then causes the CPU to load the instruction
register with a software interrupt instruction (SWI). The program counter vectors to
$FFFC and $FFFD ($FEFC and $FEFD in monitor mode).
The following events can cause a break interrupt to occur:
•
A CPU generated address (the address in the program counter) matches
the contents of the break address registers.
•
Software writes a logic 1 to the BRKA bit in the break status and control
register.
When a CPU generated address matches the contents of the break address
registers, the break interrupt is generated. A return-from-interrupt instruction (RTI)
in the break routine ends the break interrupt and returns the microcontroller unit
(MCU) to normal operation.
Figure 6-1 shows the structure of the break module.
Figure 6-2 provides a summary of the I/O registers.
MC68HC908GZ8
MOTOROLA
Data Sheet
Break Module (BRK)
For More Information On This Product,
Go to: www.freescale.com
77
Freescale Semiconductor, Inc.
Break Module (BRK)
ADDRESS BUS[15:8]
BREAK ADDRESS REGISTER HIGH
8-BIT COMPARATOR
ADDRESS BUS[15:0]
BKPT
(TO SIM)
CONTROL
8-BIT COMPARATOR
Freescale Semiconductor, Inc...
BREAK ADDRESS REGISTER LOW
ADDRESS BUS[7:0]
Figure 6-1. Break Module Block Diagram
Addr.
Register Name
$FE00
Break Status Register Read:
(BSR) Write:
See page 81. Reset:
Read:
$FE02
Reserved Write:
Reset:
$FE03
$FE09
Break Flag Control Read:
Register (BFCR) Write:
See page 82. Reset:
Break Address High Read:
Register (BRKH) Write:
See page 81. Reset:
$FE0A
Break Address Low Read:
Register (BRKL) Write:
See page 81. Reset:
$FE0B
Break Status and Control Read:
Register (BRKSCR) Write:
See page 80. Reset:
1. Writing a logic 0 clears SBSW.
Bit 7
6
5
4
3
2
R
R
R
R
R
R
1
SBSW
Note(1)
Bit 0
R
0
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
BCFE
R
R
R
R
R
R
R
Bit15
Bit14
Bit13
Bit12
Bit11
Bit10
Bit9
Bit8
0
0
0
0
0
0
0
0
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
0
0
BRKE
BRKA
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
R
= Reserved
= Unimplemented
Figure 6-2. Break I/O Register Summary
Data Sheet
78
MC68HC908GZ8
Break Module (BRK)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Break Module (BRK)
Functional Description
When the internal address bus matches the value written in the break address
registers or when software writes a logic 1 to the BRKA bit in the break status and
control register, the CPU starts a break interrupt by:
•
Loading the instruction register with the SWI instruction
•
Loading the program counter with $FFFC and $FFFD ($FEFC and $FEFD
in monitor mode)
Freescale Semiconductor, Inc...
The break interrupt timing is:
•
When a break address is placed at the address of the instruction opcode,
the instruction is not executed until after completion of the break interrupt
routine.
•
When a break address is placed at an address of an instruction operand, the
instruction is executed before the break interrupt.
•
When software writes a logic 1 to the BRKA bit, the break interrupt occurs
just before the next instruction is executed.
By updating a break address and clearing the BRKA bit in a break interrupt routine,
a break interrupt can be generated continuously.
CAUTION:
A break address should be placed at the address of the instruction opcode. When
software does not change the break address and clears the BRKA bit in the first
break interrupt routine, the next break interrupt will not be generated after exiting
the interrupt routine even when the internal address bus matches the value written
in the break address registers.
6.3.1 Flag Protection During Break Interrupts
The system integration module (SIM) controls whether or not module status bits
can be cleared during the break state. The BCFE bit in the break flag control
register (BFCR) enables software to clear status bits during the break state. See
20.7.3 Break Flag Control Register and the Break Interrupts subsection for
each module.
6.3.2 TIM During Break Interrupts
A break interrupt stops the timer counter.
6.3.3 COP During Break Interrupts
The COP is disabled during a break interrupt when VTST is present on the RST pin.
MC68HC908GZ8
MOTOROLA
Data Sheet
Break Module (BRK)
For More Information On This Product,
Go to: www.freescale.com
79
Freescale Semiconductor, Inc.
Break Module (BRK)
6.4 Break Module Registers
These registers control and monitor operation of the break module:
•
Break status and control register (BRKSCR)
•
Break address register high (BRKH)
•
Break address register low (BRKL)
•
Break status register (BSR)
•
Break flag control register (BFCR)
Freescale Semiconductor, Inc...
6.4.1 Break Status and Control Register
The break status and control register (BRKSCR) contains break module enable
and status bits.
Address: $FE0B
Read:
Write:
Reset:
Bit 7
6
BRKE
BRKA
0
0
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
0
0
0
0
= Unimplemented
Figure 6-3. Break Status and Control Register (BRKSCR)
BRKE — Break Enable Bit
This read/write bit enables breaks on break address register matches. Clear
BRKE by writing a logic 0 to bit 7. Reset clears the BRKE bit.
1 = Breaks enabled on 16-bit address match
0 = Breaks disabled
BRKA — Break Active Bit
This read/write status and control bit is set when a break address match occurs.
Writing a logic 1 to BRKA generates a break interrupt. Clear BRKA by writing a
logic 0 to it before exiting the break routine. Reset clears the BRKA bit.
1 = Break address match
0 = No break address match
Data Sheet
80
MC68HC908GZ8
Break Module (BRK)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Break Module (BRK)
Break Module Registers
6.4.2 Break Address Registers
The break address registers (BRKH and BRKL) contain the high and low bytes of
the desired breakpoint address. Reset clears the break address registers.
Address: $FE09
Read:
Write:
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
Bit 14
Bit 13
Bit 12
Bit 11
Bit 10
Bit 9
Bit 8
0
0
0
0
0
0
0
0
Freescale Semiconductor, Inc...
Figure 6-4. Break Address Register High (BRKH)
Address: $FE0A
Read:
Write:
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
0
0
0
0
0
0
0
0
Figure 6-5. Break Address Register Low (BRKL)
6.4.3 Break Status Register
The break status register (BSR) contains a flag to indicate that a break caused an
exit from wait mode. This register is only used in emulation mode.
Address: $FE00
Bit 7
Read:
Write:
R
6
R
5
R
4
R
3
R
2
R
Reset:
1
SBSW
Note(1)
Bit 0
R
0
R
= Reserved
1. Writing a logic 0 clears SBSW.
Figure 6-6. Break Status Register (BSR)
SBSW — SIM Break Stop/Wait
SBSW can be read within the break state SWI routine. The user can modify the
return address on the stack by subtracting one from it.
1 = Wait mode was exited by break interrupt
0 = Wait mode was not exited by break interrupt
MC68HC908GZ8
MOTOROLA
Data Sheet
Break Module (BRK)
For More Information On This Product,
Go to: www.freescale.com
81
Freescale Semiconductor, Inc.
Break Module (BRK)
6.4.4 Break Flag Control Register
The break control register (BFCR) contains a bit that enables software to clear
status bits while the MCU is in a break state.
Address: $FE03
Read:
Write:
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
BCFE
R
R
R
R
R
R
R
0
Freescale Semiconductor, Inc...
R
= Reserved
Figure 6-7. Break Flag Control Register (BFCR)
BCFE — Break Clear Flag Enable Bit
This read/write bit enables software to clear status bits by accessing status
registers while the MCU is in a break state. To clear status bits during the break
state, the BCFE bit must be set.
1 = Status bits clearable during break
0 = Status bits not clearable during break
6.5 Low-Power Modes
The WAIT and STOP instructions put the MCU in low power- consumption standby
modes. If enabled, the break module will remain enabled in wait and stop modes.
However, since the internal address bus does not increment in these modes, a
break interrupt will never be triggered.
Data Sheet
82
MC68HC908GZ8
Break Module (BRK)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 7. Clock Generator Module (CGM)
Freescale Semiconductor, Inc...
7.1 Introduction
This section describes the clock generator module. The CGM generates the crystal
clock signal, CGMXCLK, which operates at the frequency of the crystal. The CGM
also generates the base clock signal, CGMOUT, which is based on either the
crystal clock divided by two or the phase-locked loop (PLL) clock, CGMVCLK,
divided by two. In user mode, CGMOUT is the clock from which the SIM derives
the system clocks, including the bus clock, which is at a frequency of CGMOUT/2.
The PLL is a fully functional frequency generator designed for use with crystals or
ceramic resonators. The PLL can generate a maximum bus frequency of 8 MHz
using a 1-8MHz crystal or external clock source.
7.2 Features
Features of the CGM include:
• Phase-locked loop with output frequency in integer multiples of an integer
dividend of the crystal reference
• High-frequency crystal operation with low-power operation and high-output
frequency resolution
• Programmable hardware voltage-controlled oscillator (VCO) for low-jitter
operation
• Automatic bandwidth control mode for low-jitter operation
• Automatic frequency lock detector
• CPU interrupt on entry or exit from locked condition
• Configuration register bit to allow oscillator operation during stop mode
7.3 Functional Description
The CGM consists of three major submodules:
• Crystal oscillator circuit — The crystal oscillator circuit generates the
constant crystal frequency clock, CGMXCLK.
• Phase-locked loop (PLL) — The PLL generates the programmable VCO
frequency clock, CGMVCLK.
• Base clock selector circuit — This software-controlled circuit selects either
CGMXCLK divided by two or the VCO clock, CGMVCLK, divided by two as
the base clock, CGMOUT. The SIM derives the system clocks from either
CGMOUT or CGMXCLK.
MC68HC908GZ8
MOTOROLA
Data Sheet
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
83
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
Figure 7-1 shows the structure of the CGM.
OSCILLATOR (OSC)
OSC2
CGMXCLK
(TO: SIM, TIMTB15A, ADC)
OSC1
SIMOSCEN (FROM SIM)
Freescale Semiconductor, Inc...
OSCSTOPENB
(FROM CONFIG)
PHASE-LOCKED LOOP (PLL)
CGMRCLK
CLOCK
SELECT
CIRCUIT
BCS
VDDA
CGMXFC
÷2
A
CGMOUT
B S*
(TO SIM)
*WHEN S = 1,
VSSA
CGMOUT = B
SIMDIV2
(FROM SIM)
VPR1–VPR0
VRS7–VRS0
PHASE
DETECTOR
VOLTAGE
CONTROLLED
OSCILLATOR
LOOP
FILTER
CGMVCLK
PLL ANALOG
LOCK
DETECTOR
LOCK
AUTOMATIC
MODE
CONTROL
AUTO
ACQ
INTERRUPT
CONTROL
PLLIE
CGMINT
(TO SIM)
PLLF
MUL11–MUL0
CGMVDV
FREQUENCY
DIVIDER
Figure 7-1. CGM Block Diagram
Data Sheet
84
MC68HC908GZ8
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
Functional Description
7.3.1 Crystal Oscillator Circuit
The crystal oscillator circuit consists of an inverting amplifier and an external
crystal. The OSC1 pin is the input to the amplifier and the OSC2 pin is the output.
The SIMOSCEN signal from the system integration module (SIM) or the
OSCSTOPENB bit in the CONFIG register enable the crystal oscillator circuit.
Freescale Semiconductor, Inc...
The CGMXCLK signal is the output of the crystal oscillator circuit and runs at a rate
equal to the crystal frequency. CGMXCLK is then buffered to produce CGMRCLK,
the PLL reference clock.
CGMXCLK can be used by other modules which require precise timing for
operation. The duty cycle of CGMXCLK is not guaranteed to be 50% and depends
on external factors, including the crystal and related external components. An
externally generated clock also can feed the OSC1 pin of the crystal oscillator
circuit. Connect the external clock to the OSC1 pin and let the OSC2 pin float.
7.3.2 Phase-Locked Loop Circuit (PLL)
The PLL is a frequency generator that can operate in either acquisition mode or
tracking mode, depending on the accuracy of the output frequency. The PLL can
change between acquisition and tracking modes either automatically or manually.
7.3.3 PLL Circuits
The PLL consists of these circuits:
• Voltage-controlled oscillator (VCO)
• Modulo VCO frequency divider
• Phase detector
• Loop filter
• Lock detector
The operating range of the VCO is programmable for a wide range of frequencies
and for maximum immunity to external noise, including supply and CGMXFC noise.
The VCO frequency is bound to a range from roughly one-half to twice the
center-of-range frequency, fVRS. Modulating the voltage on the CGMXFC pin
changes the frequency within this range. By design, fVRS is equal to the nominal
center-of-range frequency, fNOM, (71.4 kHz) times a linear factor, L, and a
power-of-two factor, E, or (L × 2E)fNOM.
CGMRCLK is the PLL reference clock, a buffered version of CGMXCLK.
CGMRCLK runs at a frequency, fRCLK. The VCO’s output clock, CGMVCLK,
running at a frequency, fVCLK, is fed back through a programmable modulo divider.
The modulo divider reduces the VCO clock by a factor, N. The dividers output is
the VCO feedback clock, CGMVDV, running at a frequency, fVDV = fVCLK/(N). (For
more information, see 7.3.6 Programming the PLL.)
MC68HC908GZ8
MOTOROLA
Data Sheet
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
85
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
Freescale Semiconductor, Inc...
The phase detector then compares the VCO feedback clock, CGMVDV, with the
final reference clock, CGMRDV. A correction pulse is generated based on the
phase difference between the two signals. The loop filter then slightly alters the DC
voltage on the external capacitor connected to CGMXFC based on the width and
direction of the correction pulse. The filter can make fast or slow corrections
depending on its mode, described in 7.3.4 Acquisition and Tracking Modes. The
value of the external capacitor and the reference frequency determines the speed
of the corrections and the stability of the PLL.
The lock detector compares the frequencies of the VCO feedback clock, CGMVDV,
and the reference clock, CGMRCLK. Therefore, the speed of the lock detector is
directly proportional to the reference frequency, fRCLK. The circuit determines the
mode of the PLL and the lock condition based on this comparison.
7.3.4 Acquisition and Tracking Modes
The PLL filter is manually or automatically configurable into one of two operating
modes:
•
Acquisition mode — In acquisition mode, the filter can make large frequency
corrections to the VCO. This mode is used at PLL start up or when the PLL
has suffered a severe noise hit and the VCO frequency is far off the desired
frequency. When in acquisition mode, the ACQ bit is clear in the PLL
bandwidth control register. (See 7.5.2 PLL Bandwidth Control Register.)
•
Tracking mode — In tracking mode, the filter makes only small corrections
to the frequency of the VCO. PLL jitter is much lower in tracking mode, but
the response to noise is also slower. The PLL enters tracking mode when
the VCO frequency is nearly correct, such as when the PLL is selected as
the base clock source. (See 7.3.8 Base Clock Selector Circuit.) The PLL
is automatically in tracking mode when not in acquisition mode or when the
ACQ bit is set.
7.3.5 Manual and Automatic PLL Bandwidth Modes
The PLL can change the bandwidth or operational mode of the loop filter manually
or automatically. Automatic mode is recommended for most users.
In automatic bandwidth control mode (AUTO = 1), the lock detector automatically
switches between acquisition and tracking modes. Automatic bandwidth control
mode also is used to determine when the VCO clock, CGMVCLK, is safe to use as
the source for the base clock, CGMOUT. (See 7.5.2 PLL Bandwidth Control
Register.) If PLL interrupts are enabled, the software can wait for a PLL interrupt
request and then check the LOCK bit. If interrupts are disabled, software can poll
the LOCK bit continuously (for example, during PLL start up) or at periodic
intervals. In either case, when the LOCK bit is set, the VCO clock is safe to use as
the source for the base clock. (See 7.3.8 Base Clock Selector Circuit.) If the VCO
is selected as the source for the base clock and the LOCK bit is clear, the PLL has
suffered a severe noise hit and the software must take appropriate action,
Data Sheet
86
MC68HC908GZ8
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
Functional Description
depending on the application. (See 7.6 Interrupts for information and precautions
on using interrupts.)
Freescale Semiconductor, Inc...
The following conditions apply when the PLL is in automatic bandwidth control
mode:
•
The ACQ bit (See 7.5.2 PLL Bandwidth Control Register.) is a read-only
indicator of the mode of the filter. (See 7.3.4 Acquisition and Tracking
Modes.)
•
The ACQ bit is set when the VCO frequency is within a certain tolerance and
is cleared when the VCO frequency is out of a certain tolerance. (See 7.8
Acquisition/Lock Time Specifications for more information.)
•
The LOCK bit is a read-only indicator of the locked state of the PLL.
•
The LOCK bit is set when the VCO frequency is within a certain tolerance
and is cleared when the VCO frequency is out of a certain tolerance. (See
7.8 Acquisition/Lock Time Specifications for more information.)
•
CPU interrupts can occur if enabled (PLLIE = 1) when the PLL’s lock
condition changes, toggling the LOCK bit. (See 7.5.1 PLL Control
Register.)
The PLL also may operate in manual mode (AUTO = 0). Manual mode is used by
systems that do not require an indicator of the lock condition for proper operation.
Such systems typically operate well below fBUSMAX.
The following conditions apply when in manual mode:
•
ACQ is a writable control bit that controls the mode of the filter. Before
turning on the PLL in manual mode, the ACQ bit must be clear.
•
Before entering tracking mode (ACQ = 1), software must wait a given time,
tACQ (See 7.8 Acquisition/Lock Time Specifications.), after turning on the
PLL by setting PLLON in the PLL control register (PCTL).
•
Software must wait a given time, tAL, after entering tracking mode before
selecting the PLL as the clock source to CGMOUT (BCS = 1).
•
The LOCK bit is disabled.
•
CPU interrupts from the CGM are disabled.
MC68HC908GZ8
MOTOROLA
Data Sheet
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
87
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
7.3.6 Programming the PLL
Use the following procedure to program the PLL. For reference, the variables used
and their meaning are shown in Table 7-1.
Table 7-1. Variable Definitions
Freescale Semiconductor, Inc...
Variable
NOTE:
Definition
fBUSDES
Desired bus clock frequency
fVCLKDES
Desired VCO clock frequency
fRCLK
Chosen reference crystal frequency
fVCLK
Calculated VCO clock frequency
fBUS
Calculated bus clock frequency
fNOM
Nominal VCO center frequency
fVRS
Programmed VCO center frequency
The round function in the following equations means that the real number should
be rounded to the nearest integer number.
1. Choose the desired bus frequency, fBUSDES.
2. Calculate the desired VCO frequency (four times the desired bus
frequency).
fVCLKDES = 4 x fBUSDES
3. Choose a practical PLL (crystal) reference frequency, fRCLK. Typically, the
reference crystal is 1–8 MHz.
Frequency errors to the PLL are corrected at a rate of fRCLK.
For stability and lock time reduction, this rate must be as fast as possible.
The VCO frequency must be an integer multiple of this rate. The relationship
between the VCO frequency, fVCLK, and the reference frequency, fRCLK, is:
fVCLK = (N) (fRCLK)
N, the range multiplier, must be an integer.
In cases where desired bus frequency has some tolerance, choose fRCLK to
a value determined either by other module requirements (such as modules
which are clocked by CGMXCLK), cost requirements, or ideally, as high as
the specified range allows. See Section 24. Electrical Specifications.
After choosing N, the actual bus frequency can be determined using
equation in 2 above.
4. Select a VCO frequency multiplier, N.
 f VCLKDES
N = round  --------------------------
 f RCLK 
Data Sheet
88
MC68HC908GZ8
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
Functional Description
5. Calculate and verify the adequacy of the VCO and bus frequencies fVCLK
and fBUS.
f VCLK = ( N ) × f RCLK
f BUS = ( f VCLK ) ⁄ 4
6. Select the VCO’s power-of-two range multiplier E, according to Table 7-2.
Freescale Semiconductor, Inc...
Table 7-2. Power-of-Two Range Selectors
Frequency Range
E
0 < fVCLK ≤ 8 MHz
0
8 MHz< fVCLK ≤ 16 MHz
1
16 MHz< fVCLK ≤ 32 MHz
2(1)
1. Do not program E to a value of 3.
7. Select a VCO linear range multiplier, L, where fNOM = 71.4 kHz
fVCLK
L = Round
2E x fNOM
8. Calculate and verify the adequacy of the VCO programmed center-of-range
frequency, fVRS. The center-of-range frequency is the midpoint between the
minimum and maximum frequencies attainable by the PLL.
fVRS = (L x 2E) fNOM
9. For proper operation,
E
f NOM × 2
f VRS – f VCLK ≤ --------------------------2
10. Verify the choice of N, E, and L by comparing fVCLK to fVRS and fVCLKDES.
For proper operation, fVCLK must be within the application’s tolerance of
fVCLKDES, and fVRS must be as close as possible to fVCLK.
NOTE:
Exceeding the recommended maximum bus frequency or VCO frequency can
crash the MCU.
11. Program the PLL registers accordingly:
a. In the VPR bits of the PLL control register (PCTL), program the binary
equivalent of E.
b. In the PLL multiplier select register low (PMSL) and the PLL multiplier
select register high (PMSH), program the binary equivalent of N. If
using a 1–8 MHz reference, the PMSL register must be reprogrammed
from the reset value before enabling the pll.
c. In the PLL VCO range select register (PMRS), program the binary
coded equivalent of L.
MC68HC908GZ8
MOTOROLA
Data Sheet
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
89
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
Table 7-3 provides numeric examples (register values are in hexadecimal
notation):
Freescale Semiconductor, Inc...
Table 7-3. Numeric Example
fBUS
fRCLK
N
E
L
500 kHz
1 MHz
002
0
1B
1.25 MHz
1 MHz
005
0
45
2.0 MHz
1 MHz
008
0
70
2.5 MHz
1 MHz
00A
1
45
3.0 MHz
1 MHz
00C
1
53
4.0 MHz
1 MHz
010
1
70
5.0 MHz
1 MHz
014
2
46
7.0 MHz
1 MHz
01C
2
62
8.0 MHz
1 MHz
020
2
70
7.3.7 Special Programming Exceptions
The programming method described in 7.3.6 Programming the PLL does not
account for two possible exceptions. A value of 0 for N or L is meaningless when
used in the equations given. To account for these exceptions:
•
A 0 value for N is interpreted exactly the same as a value of 1.
•
A 0 value for L disables the PLL and prevents its selection as the source for
the base clock.
See 7.3.8 Base Clock Selector Circuit.
7.3.8 Base Clock Selector Circuit
This circuit is used to select either the crystal clock, CGMXCLK, or the VCO clock,
CGMVCLK, as the source of the base clock, CGMOUT. The two input clocks go
through a transition control circuit that waits up to three CGMXCLK cycles and
three CGMVCLK cycles to change from one clock source to the other. During this
time, CGMOUT is held in stasis. The output of the transition control circuit is then
divided by two to correct the duty cycle. Therefore, the bus clock frequency, which
is one-half of the base clock frequency, is one-fourth the frequency of the selected
clock (CGMXCLK or CGMVCLK).
The BCS bit in the PLL control register (PCTL) selects which clock drives
CGMOUT. The VCO clock cannot be selected as the base clock source if the PLL
is not turned on. The PLL cannot be turned off if the VCO clock is selected. The
PLL cannot be turned on or off simultaneously with the selection or deselection of
the VCO clock. The VCO clock also cannot be selected as the base clock source
if the factor L is programmed to a 0. This value would set up a condition
inconsistent with the operation of the PLL, so that the PLL would be disabled and
the crystal clock would be forced as the source of the base clock.
Data Sheet
90
MC68HC908GZ8
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
Functional Description
7.3.9 CGM External Connections
In its typical configuration, the CGM requires external components. Five of these
are for the crystal oscillator and two or four are for the PLL.
Freescale Semiconductor, Inc...
The crystal oscillator is normally connected in a Pierce oscillator configuration, as
shown in Figure 7-2. Figure 7-2 shows only the logical representation of the
internal components and may not represent actual circuitry. The oscillator
configuration uses five components:
• Crystal, X1
• Fixed capacitor, C1
• Tuning capacitor, C2 (can also be a fixed capacitor)
• Feedback resistor, RB
• Series resistor, RS
The series resistor (RS) is included in the diagram to follow strict Pierce oscillator
guidelines. Refer to the crystal manufacturer’s data for more information regarding
values for C1 and C2.
Figure 7-2 also shows the external components for the PLL:
• Bypass capacitor, CBYP
• Filter network
Routing should be done with great care to minimize signal cross talk and noise.
SIMOSCEN
OSCSTOPENB
(FROM CONFIG)
CGMXCLK
OSC1
CGMXFC
OSC2
VSSA
VDDA
VDD
RB
RF1
RS
CF2
CBYP
0.1 µF
CF1
X1
C1
3 Component Filter
C2
Note: Filter network in box can be replaced with a single capacitor, but will degrade stability.
Figure 7-2. CGM External Connections
MC68HC908GZ8
MOTOROLA
Data Sheet
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
91
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
7.4 I/O Signals
The following paragraphs describe the CGM I/O signals.
7.4.1 Crystal Amplifier Input Pin (OSC1)
The OSC1 pin is an input to the crystal oscillator amplifier.
7.4.2 Crystal Amplifier Output Pin (OSC2)
Freescale Semiconductor, Inc...
The OSC2 pin is the output of the crystal oscillator inverting amplifier.
7.4.3 External Filter Capacitor Pin (CGMXFC)
The CGMXFC pin is required by the loop filter to filter out phase corrections. An
external filter network is connected to this pin. (See Figure 7-2.)
NOTE:
To prevent noise problems, the filter network should be placed as close to the
CGMXFC pin as possible, with minimum routing distances and no routing of other
signals across the network.
7.4.4 PLL Analog Power Pin (VDDA)
VDDA is a power pin used by the analog portions of the PLL. Connect the VDDA pin
to the same voltage potential as the VDD pin.
NOTE:
Route VDDA carefully for maximum noise immunity and place bypass capacitors as
close as possible to the package.
7.4.5 PLL Analog Ground Pin (VSSA)
VSSA is a ground pin used by the analog portions of the PLL. Connect the VSSA pin
to the same voltage potential as the VSS pin.
NOTE:
Route VSSA carefully for maximum noise immunity and place bypass capacitors as
close as possible to the package.
7.4.6 Oscillator Enable Signal (SIMOSCEN)
The SIMOSCEN signal comes from the system integration module (SIM) and
enables the oscillator and PLL.
7.4.7 Oscillator Stop Mode Enable Bit (OSCSTOPENB)
OSCSTOPENB is a bit in the CONFIG register that enables the oscillator to
continue operating during stop mode. If this bit is set, the Oscillator continues
running during stop mode. If this bit is not set (default), the oscillator is controlled
by the SIMOSCEN signal which will disable the oscillator during stop mode.
Data Sheet
92
MC68HC908GZ8
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
CGM Registers
7.4.8 Crystal Output Frequency Signal (CGMXCLK)
CGMXCLK is the crystal oscillator output signal. It runs at the full speed of the
crystal (fXCLK) and comes directly from the crystal oscillator circuit. Figure 7-2
shows only the logical relation of CGMXCLK to OSC1 and OSC2 and may not
represent the actual circuitry. The duty cycle of CGMXCLK is unknown and may
depend on the crystal and other external factors. Also, the frequency and amplitude
of CGMXCLK can be unstable at start up.
Freescale Semiconductor, Inc...
7.4.9 CGM Base Clock Output (CGMOUT)
CGMOUT is the clock output of the CGM. This signal goes to the SIM, which
generates the MCU clocks. CGMOUT is a 50 percent duty cycle clock running at
twice the bus frequency. CGMOUT is software programmable to be either the
oscillator output, CGMXCLK, divided by two or the VCO clock, CGMVCLK, divided
by two.
7.4.10 CGM CPU Interrupt (CGMINT)
CGMINT is the interrupt signal generated by the PLL lock detector.
7.5 CGM Registers
These registers control and monitor operation of the CGM:
•
PLL control register (PCTL)
(See 7.5.1 PLL Control Register.)
•
PLL bandwidth control register (PBWC)
(See 7.5.2 PLL Bandwidth Control Register.)
•
PLL multiplier select register high (PMSH)
(See 7.5.3 PLL Multiplier Select Register High.)
•
PLL multiplier select register low (PMSL)
(See 7.5.4 PLL Multiplier Select Register Low.)
•
PLL VCO range select register (PMRS)
(See 7.5.5 PLL VCO Range Select Register.)
Figure 7-3 is a summary of the CGM registers.
MC68HC908GZ8
MOTOROLA
Data Sheet
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
93
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
Addr.
Register Name
Bit 7
PLL Control Register Read:
(PCTL) Write:
See page 94. Reset:
$0036
PLL Bandwidth Control Reg- Read:
$0037
ister (PBWC) Write:
See page 96. Reset:
Freescale Semiconductor, Inc...
$0038
PLLIE
$0039
$003A
PLL VCO Select Range Read:
Register (PMRS) Write:
See page 98. Reset:
5
4
3
2
1
Bit 0
PLLON
BCS
R
R
VPR1
VPR0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
MUL11
MUL10
MUL9
MUL8
0
AUTO
LOCK
ACQ
R
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
MUL7
MUL6
MUL5
MUL4
MUL3
MUL2
MUL1
MUL0
0
1
0
0
0
0
0
0
VRS7
VRS6
VRS5
VRS4
VRS3
VRS2
VRS1
VRS0
0
1
0
0
0
0
0
0
0
0
0
0
R
R
R
R
0
0
0
0
0
0
0
1
R
= Reserved
Read:
$003B
PLLF
0
PLL Multiplier Select High Read:
Register (PMSH) Write:
See page 97. Reset:
PLL Multiplier Select Low Read:
Register (PMSL) Write:
See page 98. Reset:
6
Reserved Register Write:
Reset:
= Unimplemented
NOTES:
1. When AUTO = 0, PLLIE is forced clear and is read-only.
2. When AUTO = 0, PLLF and LOCK read as clear.
3. When AUTO = 1, ACQ is read-only.
4. When PLLON = 0 or VRS7:VRS0 = $0, BCS is forced clear and is read-only.
5. When PLLON = 1, the PLL programming register is read-only.
6. When BCS = 1, PLLON is forced set and is read-only.
Figure 7-3. CGM I/O Register Summary
7.5.1 PLL Control Register
The PLL control register (PCTL) contains the interrupt enable and flag bits, the
on/off switch, the base clock selector bit, and the VCO power-of-two range selector
bits.
Address:
$0036
Bit 7
Read:
6
5
4
3
2
1
Bit 0
PLLON
BCS
R
R
VPR1
VPR0
1
0
0
0
0
0
R
= Reserved
PLLF
PLLIE
Write:
Reset:
0
0
= Unimplemented
Figure 7-4. PLL Control Register (PCTL)
Data Sheet
94
MC68HC908GZ8
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
CGM Registers
PLLIE — PLL Interrupt Enable Bit
This read/write bit enables the PLL to generate an interrupt request when the
LOCK bit toggles, setting the PLL flag, PLLF. When the AUTO bit in the PLL
bandwidth control register (PBWC) is clear, PLLIE cannot be written and reads
as logic 0. Reset clears the PLLIE bit.
1 = PLL interrupts enabled
0 = PLL interrupts disabled
Freescale Semiconductor, Inc...
PLLF — PLL Interrupt Flag Bit
This read-only bit is set whenever the LOCK bit toggles. PLLF generates an
interrupt request if the PLLIE bit also is set. PLLF always reads as logic 0 when
the AUTO bit in the PLL bandwidth control register (PBWC) is clear. Clear the
PLLF bit by reading the PLL control register. Reset clears the PLLF bit.
1 = Change in lock condition
0 = No change in lock condition
NOTE:
Do not inadvertently clear the PLLF bit. Any read or read-modify-write operation on
the PLL control register clears the PLLF bit.
PLLON — PLL On Bit
This read/write bit activates the PLL and enables the VCO clock, CGMVCLK.
PLLON cannot be cleared if the VCO clock is driving the base clock, CGMOUT
(BCS = 1). (See 7.3.8 Base Clock Selector Circuit.) Reset sets this bit so that
the loop can stabilize as the MCU is powering up.
1 = PLL on
0 = PLL off
BCS — Base Clock Select Bit
This read/write bit selects either the crystal oscillator output, CGMXCLK, or the
VCO clock, CGMVCLK, as the source of the CGM output, CGMOUT. CGMOUT
frequency is one-half the frequency of the selected clock. BCS cannot be set
while the PLLON bit is clear. After toggling BCS, it may take up to three
CGMXCLK and three CGMVCLK cycles to complete the transition from one
source clock to the other. During the transition, CGMOUT is held in stasis. (See
7.3.8 Base Clock Selector Circuit.) Reset clears the BCS bit.
1 = CGMVCLK divided by two drives CGMOUT
0 = CGMXCLK divided by two drives CGMOUT
NOTE:
PLLON and BCS have built-in protection that prevents the base clock selector
circuit from selecting the VCO clock as the source of the base clock if the PLL is
off. Therefore, PLLON cannot be cleared when BCS is set, and BCS cannot be set
when PLLON is clear. If the PLL is off (PLLON = 0), selecting CGMVCLK requires
two writes to the PLL control register. (See 7.3.8 Base Clock Selector Circuit.).
VPR1 and VPR0 — VCO Power-of-Two Range Select Bits
These read/write bits control the VCO’s hardware power-of-two range multiplier
E that, in conjunction with L controls the hardware center-of-range frequency,
fVRS. VPR1:VPR0 cannot be written when the PLLON bit is set. Reset clears
MC68HC908GZ8
MOTOROLA
Data Sheet
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
95
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
these bits. (See 7.3.3 PLL Circuits, 7.3.6 Programming the PLL, and 7.5.5
PLL VCO Range Select Register.)
Table 7-4. VPR1 and VPR0 Programming
VPR1 and VPR0
E
VCO Power-of-Two
Range Multiplier
00
0
1
01
1
2
10
2(1)
4
Freescale Semiconductor, Inc...
1. Do not program E to a value of 3.
NOTE:
Verify that the value of the VPR1 and VPR0 bits in the PCTL register are
appropriate for the given reference and VCO clock frequencies before enabling the
PLL. See 7.3.6 Programming the PLL for detailed instructions on selecting the
proper value for these control bits.
7.5.2 PLL Bandwidth Control Register
The PLL bandwidth control register (PBWC):
•
Selects automatic or manual (software-controlled) bandwidth control mode
•
Indicates when the PLL is locked
•
In automatic bandwidth control mode, indicates when the PLL is in
acquisition or tracking mode
•
In manual operation, forces the PLL into acquisition or tracking mode
Address:
$0037
Bit 7
Read:
Write:
Reset:
6
AUTO
0
LOCK
5
ACQ
0
= Unimplemented
0
4
3
2
1
0
0
0
0
0
0
0
0
R
Bit 0
R
0
= Reserved
Figure 7-5. PLL Bandwidth Control Register (PBWC)
AUTO — Automatic Bandwidth Control Bit
This read/write bit selects automatic or manual bandwidth control. When
initializing the PLL for manual operation (AUTO = 0), clear the ACQ bit before
turning on the PLL. Reset clears the AUTO bit.
1 = Automatic bandwidth control
0 = Manual bandwidth control
LOCK — Lock Indicator Bit
When the AUTO bit is set, LOCK is a read-only bit that becomes set when the
VCO clock, CGMVCLK, is locked (running at the programmed frequency).
Data Sheet
96
MC68HC908GZ8
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
CGM Registers
Freescale Semiconductor, Inc...
When the AUTO bit is clear, LOCK reads as logic 0 and has no meaning. The
write one function of this bit is reserved for test, so this bit must always be
written a 0. Reset clears the LOCK bit.
1 = VCO frequency correct or locked
0 = VCO frequency incorrect or unlocked
ACQ — Acquisition Mode Bit
When the AUTO bit is set, ACQ is a read-only bit that indicates whether the PLL
is in acquisition mode or tracking mode. When the AUTO bit is clear, ACQ is a
read/write bit that controls whether the PLL is in acquisition or tracking mode.
In automatic bandwidth control mode (AUTO = 1), the last-written value from
manual operation is stored in a temporary location and is recovered when
manual operation resumes. Reset clears this bit, enabling acquisition mode.
1 = Tracking mode
0 = Acquisition mode
7.5.3 PLL Multiplier Select Register High
The PLL multiplier select register high (PMSH) contains the programming
information for the high byte of the modulo feedback divider.
Address:
Read:
$0038
Bit 7
6
5
4
0
0
0
0
3
2
1
Bit 0
MUL11
MUL10
MUL9
MUL8
0
0
0
0
Write:
Reset:
0
0
0
0
= Unimplemented
Figure 7-6. PLL Multiplier Select Register High (PMSH)
MUL11–MUL8 — Multiplier Select Bits
These read/write bits control the high byte of the modulo feedback divider that
selects the VCO frequency multiplier N. (See 7.3.3 PLL Circuits and 7.3.6
Programming the PLL.) A value of $0000 in the multiplier select registers
configures the modulo feedback divider the same as a value of $0001. Reset
initializes the registers to $0040 for a default multiply value of 64.
NOTE:
The multiplier select bits have built-in protection such that they cannot be written
when the PLL is on (PLLON = 1).
PMSH[7:4] — Unimplemented Bits
These bits have no function and always read as logic 0s.
MC68HC908GZ8
MOTOROLA
Data Sheet
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
97
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
7.5.4 PLL Multiplier Select Register Low
The PLL multiplier select register low (PMSL) contains the programming
information for the low byte of the modulo feedback divider.
Address:
Read:
Write:
Reset:
$0038
Bit 7
6
5
4
3
2
1
Bit 0
MUL7
MUL6
MUL5
MUL4
MUL3
MUL2
MUL1
MUL0
0
1
0
0
0
0
0
0
Freescale Semiconductor, Inc...
Figure 7-7. PLL Multiplier Select Register Low (PMSL)
NOTE:
For applications using 1–8 MHz reference frequencies this register must be
reprogrammed before enabling the PLL. The reset value of this register will cause
applications using 1–8 MHz reference frequencies to become unstable if the PLL
is enabled without programming an appropriate value. The programmed value
must not allow the VCO clock to exceed 32 MHz. See 7.3.6 Programming the PLL
for detailed instructions on choosing the proper value for PMSL.
MUL7–MUL0 — Multiplier Select Bits
These read/write bits control the low byte of the modulo feedback divider that
selects the VCO frequency multiplier, N. (See 7.3.3 PLL Circuits and
7.3.6 Programming the PLL.) MUL7–MUL0 cannot be written when the
PLLON bit in the PCTL is set. A value of $0000 in the multiplier select registers
configures the modulo feedback divider the same as a value of $0001. Reset
initializes the register to $40 for a default multiply value of 64.
NOTE:
The multiplier select bits have built-in protection such that they cannot be written
when the PLL is on (PLLON = 1).
7.5.5 PLL VCO Range Select Register
NOTE:
PMRS may be called PVRS on other HC08 derivatives.
The PLL VCO range select register (PMRS) contains the programming information
required for the hardware configuration of the VCO.
Address:
Read:
Write:
Reset:
$003A
Bit 7
6
5
4
3
2
1
Bit 0
VRS7
VRS6
VRS5
VRS4
VRS3
VRS2
VRS1
VRS0
0
1
0
0
0
0
0
0
Figure 7-8. PLL VCO Range Select Register (PMRS)
NOTE:
Verify that the value of the PMRS register is appropriate for the given reference and
VCO clock frequencies before enabling the PLL. See 7.3.6 Programming the PLL
for detailed instructions on selecting the proper value for these control bits.
Data Sheet
98
MC68HC908GZ8
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
Interrupts
VRS7–VRS0 — VCO Range Select Bits
These read/write bits control the hardware center-of-range linear multiplier L
which, in conjunction with E (See 7.3.3 PLL Circuits, 7.3.6 Programming the
PLL, and 7.5.1 PLL Control Register.), controls the hardware center-of-range
frequency, fVRS. VRS7–VRS0 cannot be written when the PLLON bit in the
PCTL is set. (See 7.3.7 Special Programming Exceptions.) A value of $00 in
the VCO range select register disables the PLL and clears the BCS bit in the
PLL control register (PCTL). (See 7.3.8 Base Clock Selector Circuit and
7.3.7 Special Programming Exceptions.). Reset initializes the register to $40
for a default range multiply value of 64.
Freescale Semiconductor, Inc...
NOTE:
The VCO range select bits have built-in protection such that they cannot be written
when the PLL is on (PLLON = 1) and such that the VCO clock cannot be selected
as the source of the base clock (BCS = 1) if the VCO range select bits are all clear.
The PLL VCO range select register must be programmed correctly. Incorrect
programming can result in failure of the PLL to achieve lock.
7.6 Interrupts
When the AUTO bit is set in the PLL bandwidth control register (PBWC), the PLL
can generate a CPU interrupt request every time the LOCK bit changes state. The
PLLIE bit in the PLL control register (PCTL) enables CPU interrupts from the PLL.
PLLF, the interrupt flag in the PCTL, becomes set whether interrupts are enabled
or not. When the AUTO bit is clear, CPU interrupts from the PLL are disabled and
PLLF reads as logic 0.
Software should read the LOCK bit after a PLL interrupt request to see if the
request was due to an entry into lock or an exit from lock. When the PLL enters
lock, the VCO clock, CGMVCLK, divided by two can be selected as the CGMOUT
source by setting BCS in the PCTL. When the PLL exits lock, the VCO clock
frequency is corrupt, and appropriate precautions should be taken. If the
application is not frequency sensitive, interrupts should be disabled to prevent PLL
interrupt service routines from impeding software performance or from exceeding
stack limitations.
NOTE:
Software can select the CGMVCLK divided by two as the CGMOUT source even
if the PLL is not locked (LOCK = 0). Therefore, software should make sure the PLL
is locked before setting the BCS bit.
7.7 Special Modes
The WAIT instruction puts the MCU in low power-consumption standby modes.
7.7.1 Wait Mode
The WAIT instruction does not affect the CGM. Before entering wait mode,
software can disengage and turn off the PLL by clearing the BCS and PLLON bits
MC68HC908GZ8
MOTOROLA
Data Sheet
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
99
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
in the PLL control register (PCTL) to save power. Less power-sensitive
applications can disengage the PLL without turning it off, so that the PLL clock is
immediately available at WAIT exit. This would be the case also when the PLL is
to wake the MCU from wait mode, such as when the PLL is first enabled and
waiting for LOCK or LOCK is lost.
7.7.2 Stop Mode
Freescale Semiconductor, Inc...
If the OSCSTOPENB bit in the CONFIG register is cleared (default), then the
STOP instruction disables the CGM (oscillator and phase locked loop) and holds
low all CGM outputs (CGMXCLK, CGMOUT, and CGMINT).
If the OSCSTOPENB bit in the CONFIG register is set, then the phase locked loop
is shut off but the oscillator will continue to operate in stop mode.
7.7.3 CGM During Break Interrupts
The system integration module (SIM) controls whether status bits in other modules
can be cleared during the break state. The BCFE bit in the SIM break flag control
register (SBFCR) enables software to clear status bits during the break state. (See
20.7.3 Break Flag Control Register.)
To allow software to clear status bits during a break interrupt, write a logic 1 to the
BCFE bit. If a status bit is cleared during the break state, it remains cleared when
the MCU exits the break state.
To protect the PLLF bit during the break state, write a logic 0 to the BCFE bit. With
BCFE at logic 0 (its default state), software can read and
write the PLL control register during the break state without affecting the PLLF bit.
7.8 Acquisition/Lock Time Specifications
The acquisition and lock times of the PLL are, in many applications, the most
critical PLL design parameters. Proper design and use of the PLL ensures the
highest stability and lowest acquisition/lock times.
7.8.1 Acquisition/Lock Time Definitions
Typical control systems refer to the acquisition time or lock time as the reaction
time, within specified tolerances, of the system to a step input. In a PLL, the step
input occurs when the PLL is turned on or when it suffers a noise hit. The tolerance
is usually specified as a percent of the step input or when the output settles to the
desired value plus or minus a percent of the frequency change. Therefore, the
reaction time is constant in this definition, regardless of the size of the step input.
For example, consider a system with a 5 percent acquisition time tolerance. If a
command instructs the system to change from 0 Hz to 1 MHz, the acquisition time
is the time taken for the frequency to reach 1 MHz ±50 kHz. Fifty kHz = 5% of the
1-MHz step input. If the system is operating at 1 MHz and suffers a –100-kHz noise
Data Sheet
100
MC68HC908GZ8
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
Acquisition/Lock Time Specifications
hit, the acquisition time is the time taken to return from 900 kHz to 1 MHz ±5 kHz.
Five kHz = 5% of the 100-kHz step input.
Other systems refer to acquisition and lock times as the time the system takes to
reduce the error between the actual output and the desired output to within
specified tolerances. Therefore, the acquisition or lock time varies according to the
original error in the output. Minor errors may not even be registered. Typical PLL
applications prefer to use this definition because the system requires the output
frequency to be within a certain tolerance of the desired frequency regardless of
the size of the initial error.
Freescale Semiconductor, Inc...
7.8.2 Parametric Influences on Reaction Time
Acquisition and lock times are designed to be as short as possible while still
providing the highest possible stability. These reaction times are not constant,
however. Many factors directly and indirectly affect the acquisition time.
The most critical parameter which affects the reaction times of the PLL is the
reference frequency, fRCLK. This frequency is the input to the phase detector
and controls how often the PLL makes corrections. For stability, the corrections
must be small compared to the desired frequency, so several corrections are
required to reduce the frequency error. Therefore, the slower the reference the
longer it takes to make these corrections. This parameter is under user control via
the choice of crystal frequency fXCLK. (See 7.3.3 PLL Circuits and 7.3.6
Programming the PLL.)
Another critical parameter is the external filter network. The PLL modifies the
voltage on the VCO by adding or subtracting charge from capacitors in this
network. Therefore, the rate at which the voltage changes for a given frequency
error (thus change in charge) is proportional to the capacitance. The size of the
capacitor also is related to the stability of the PLL. If the capacitor is too small, the
PLL cannot make small enough adjustments to the voltage and the system cannot
lock. If the capacitor is too large, the PLL may not be able to adjust the voltage in
a reasonable time. (See 7.8.3 Choosing a Filter.)
Also important is the operating voltage potential applied to VDDA. The power supply
potential alters the characteristics of the PLL. A fixed value is best. Variable
supplies, such as batteries, are acceptable if they vary within a known range at very
slow speeds. Noise on the power supply is not acceptable, because it causes small
frequency errors which continually change the acquisition time of the PLL.
Temperature and processing also can affect acquisition time because the electrical
characteristics of the PLL change. The part operates as specified as long as these
influences stay within the specified limits. External factors, however, can cause
drastic changes in the operation of the PLL. These factors include noise injected
into the PLL through the filter capacitor, filter capacitor leakage, stray impedances
on the circuit board, and even humidity or circuit board contamination.
MC68HC908GZ8
MOTOROLA
Data Sheet
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
101
Freescale Semiconductor, Inc.
Clock Generator Module (CGM)
7.8.3 Choosing a Filter
As described in 7.8.2 Parametric Influences on Reaction Time, the external filter
network is critical to the stability and reaction time of the PLL. The PLL is also
dependent on reference frequency and supply voltage.
Freescale Semiconductor, Inc...
Figure 7-9 shows two types of filter circuits. In low-cost applications, where stability
and reaction time of the PLL are not critical, the three component filter network
shown in Figure 7-9 (B) can be replaced by a single capacitor, CF, as shown in
shown in Figure 7-9 (A). Refer to Table 7-5 for recommended filter components at
various reference frequencies. For reference frequencies between the values
listed in the table, extrapolate to the nearest common capacitor value. In general,
a slightly larger capacitor provides more stability at the expense of increased lock
time.
CGMXFC
CGMXFC
RF1
CF2
CF
CF1
VSSA
VSSA
(A)
(B)
Figure 7-9. PLL Filter
Table 7-5. Example Filter Component Values
fRCLK
CF1
CF2
RF1
CF
1 MHz
8.2 nF
820 pF
2k
18 nF
2 MHz
4.7 nF
470 pF
2k
6.8 nF
3 MHz
3.3 nF
330 pF
2k
5.6 nF
4 MHz
2.2 nF
220 pF
2k
4.7 nF
5 MHz
1.8 nF
180 pF
2k
3.9 nF
6 MHz
1.5 nF
150 pF
2k
3.3 nF
7 MHz
1.2 nF
120 pF
2k
2.7 nF
8 MHz
1 nF
100 pF
2k
2.2 nF
Data Sheet
102
MC68HC908GZ8
Clock Generator Module (CGM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 8. Configuration Register (CONFIG)
8.1 Introduction
Freescale Semiconductor, Inc...
This section describes the configuration registers, CONFIG1 and CONFIG2. The
configuration registers enable or disable these options:
•
Stop mode recovery time (32 CGMXCLK cycles or 4096 CGMXCLK cycles)
•
COP timeout period (218 – 24 or 213 – 24 COPCLK cycles)
•
STOP instruction
•
Computer operating properly module (COP)
•
Low-voltage inhibit (LVI) module control and voltage trip point selection
•
Enable/disable the oscillator (OSC) during stop mode
•
Enable/disable an extra divide by 128 prescaler in timebase module
•
Enable for Motorola scalable controller area network (MSCAN)
8.2 Functional Description
The configuration registers are used in the initialization of various options. The
configuration registers can be written once after each reset. All of the configuration
register bits are cleared during reset. Since the various options affect the operation
of the microcontroller unit (MCU), it is recommended that these registers be written
immediately after reset. The configuration registers are located at $001E and
$001F and may be read at anytime.
NOTE:
On a FLASH device, the options except LVI5OR3 are one-time writable by the user
after each reset. The LVI5OR3 bit is one-time writable by the user only after each
POR (power-on reset). The CONFIG registers are not in the FLASH memory but
are special registers containing one-time writable latches after each reset. Upon a
reset, the CONFIG registers default to predetermined settings as shown in Figure
8-1 and Figure 8-2.
MC68HC908GZ8
MOTOROLA
Data Sheet
Configuration Register (CONFIG)
For More Information On This Product,
Go to: www.freescale.com
103
Freescale Semiconductor, Inc.
Configuration Register (CONFIG)
Address:
Read:
$001E
Bit 7
6
5
4
0
0
0
0
0
0
0
0
Write:
Reset:
3
2
MSCAN-EN TMCLKSEL
See note
1
Bit 0
OSCEN-INSCIBDSRC
STOP
0
0
1
Note: MSCANEN is only reset via POR (power-on reset).
= Unimplemented
Freescale Semiconductor, Inc...
Figure 8-1. Configuration Register 2 (CONFIG2)
Address:
Read:
Write:
Reset:
$001F
Bit 7
6
5
4
3
2
1
Bit 0
COPRS
LVISTOP
LVIRSTD
LVIPWRD
LVI5OR3
SSREC
STOP
COPD
0
0
0
0
See note
0
0
0
Note: LVI5OR3 is only reset via POR (power-on reset).
Figure 8-2. Configuration Register 1 (CONFIG1)
MSCANEN— MSCAN08 Enable Bit
Setting the MSCANEN enables the MSCAN08 module and allows the MSCAN08
to use the PTC0/PTC1 pins. See Section 16. MSCAN08 Controller
(MSCAN08) for a more detailed description of the MSCAN08 operation.
1 = Enables MSCAN08 module
0 = Disables the MSCAN08 module
NOTE:
The MSCANEN bit is cleared by a power-on reset (POR) only. Other resets will
leave this bit unaffected.
TMCLKSEL— Timebase Clock Select Bit
TMCLKSEL enables an extra divide-by-128 prescaler in the timebase module.
Setting this bit enables the extra prescaler and clearing this bit disables it. See
Section 7. Clock Generator Module (CGM) for a more detailed description of
the external clock operation.
1 = Enables extra divide-by-128 prescaler in timebase module
0 = Disables extra divide-by-128 prescaler in timebase module
OSCENINSTOP — Oscillator Enable In Stop Mode Bit
OSCENINSTOP, when set, will enable the oscillator to continue to generate
clocks in stop mode. See Section 7. Clock Generator Module (CGM). This
function is used to keep the timebase running while the reset of the MCU stops.
See Section 22. Timebase Module (TBM). When clear, oscillator will cease to
generate clocks while in stop mode. The default state for this option is clear,
disabling the oscillator in stop mode.
1 = Oscillator enabled to operate during stop mode
0 = Oscillator disabled during stop mode (default)
Data Sheet
104
MC68HC908GZ8
Configuration Register (CONFIG)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Configuration Register (CONFIG)
Functional Description
SCIBDSRC — SCI Baud Rate Clock Source Bit
SCIBDSRC controls the clock source used for the serial communications
interface (SCI). The setting of this bit affects the frequency at which the SCI
operates.See Section 19. Enhanced Serial Communications Interface
(ESCI) Module.
1 = Internal data bus clock used as clock source for SCI (default)
0 = External oscillator used as clock source for SCI
Freescale Semiconductor, Inc...
COPRS — COP Rate Select Bit
COPD selects the COP timeout period. Reset clears COPRS. See Section 9.
Computer Operating Properly (COP) Module
1 = COP timeout period = 213 – 24 COPCLK cycles
0 = COP timeout period = 218 – 24 COPCLK cycles
LVISTOP — LVI Enable in Stop Mode Bit
When the LVIPWRD bit is clear, setting the LVISTOP bit enables the LVI to
operate during stop mode. Reset clears LVISTOP.
1 = LVI enabled during stop mode
0 = LVI disabled during stop mode
LVIRSTD — LVI Reset Disable Bit
LVIRSTD disables the reset signal from the LVI module.
See Section 14. Low-Voltage Inhibit (LVI).
1 = LVI module resets disabled
0 = LVI module resets enabled
LVIPWRD — LVI Power Disable Bit
LVIPWRD disables the LVI module. See Section 14. Low-Voltage Inhibit
(LVI).
1 = LVI module power disabled
0 = LVI module power enabled
LVI5OR3 — LVI 5-V or 3-V Operating Mode Bit
LVI5OR3 selects the voltage operating mode of the LVI module (see Section
14. Low-Voltage Inhibit (LVI)). The voltage mode selected for the LVI should
match the operating VDD (see Section 24. Electrical Specifications) for the
LVI’s voltage trip points for each of the modes.
1 = LVI operates in 5-V mode
0 = LVI operates in 3-V mode
NOTE:
The LVI5OR3 bit is cleared by a power-on reset (POR) only. Other resets will leave
this bit unaffected.
SSREC — Short Stop Recovery Bit
SSREC enables the CPU to exit stop mode with a delay of 32 CGMXCLK cycles
instead of a 4096-CGMXCLK cycle delay.
1 = Stop mode recovery after 32 CGMXCLK cycles
0 = Stop mode recovery after 4096 CGMXCLCK cycles
NOTE:
Exiting stop mode by an LVI reset will result in the long stop recovery.
MC68HC908GZ8
MOTOROLA
Data Sheet
Configuration Register (CONFIG)
For More Information On This Product,
Go to: www.freescale.com
105
Freescale Semiconductor, Inc.
Configuration Register (CONFIG)
Freescale Semiconductor, Inc...
If the system clock source selected is the internal oscillator or the external
crystal and the OSCENINSTOP configuration bit is not set, the oscillator will be
disabled during stop mode. The short stop recovery does not provide enough
time for oscillator stabilization and for this reason the SSREC bit should not be
set.
When using the LVI during normal operation but disabling during stop mode, the
LVI will have an enable time of tEN. The system stabilization time for power-on
reset and long stop recovery (both 4096 CGMXCLK cycles) gives a delay longer
than the LVI enable time for these startup scenarios. There is no period where
the MCU is not protected from a low-power condition. However, when using the
short stop recovery configuration option, the 32-CGMXCLK delay must be
greater than the LVI’s turn on time to avoid a period in startup where the LVI is
not protecting the MCU.
STOP — STOP Instruction Enable Bit
STOP enables the STOP instruction.
1 = STOP instruction enabled
0 = STOP instruction treated as illegal opcode
COPD — COP Disable Bit
COPD disables the COP module. See Section 9. Computer Operating
Properly (COP) Module.
1 = COP module disabled
0 = COP module enabled
Data Sheet
106
MC68HC908GZ8
Configuration Register (CONFIG)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 9. Computer Operating Properly (COP) Module
The computer operating properly (COP) module contains a free-running counter
that generates a reset if allowed to overflow. The COP module helps software
recover from runaway code. Prevent a COP reset by clearing the COP counter
periodically. The COP module can be disabled through the COPD bit in the
CONFIG register.
9.2 Functional Description
Figure 9-1 shows the structure of the COP module.
RESET STATUS REGISTER
COP TIMEOUT
STOP INSTRUCTION
INTERNAL RESET SOURCES
RESET VECTOR FETCH
RESET CIRCUIT
12-BIT COP PRESCALER
CLEAR STAGES 5–12
CGMXCLK
CLEAR ALL STAGES
Freescale Semiconductor, Inc...
9.1 Introduction
COPCTL WRITE
COP CLOCK
COP MODULE
6-BIT COP COUNTER
COPEN (FROM SIM)
COP DISABLE
(FROM CONFIG)
RESET
COPCTL WRITE
CLEAR
COP COUNTER
COP RATE SEL
(FROM CONFIG)
Figure 9-1. COP Block Diagram
MC68HC908GZ8
MOTOROLA
Data Sheet
Computer Operating Properly (COP) Module
For More Information On This Product,
Go to: www.freescale.com
107
Freescale Semiconductor, Inc.
Computer Operating Properly (COP) Module
The COP counter is a free-running 6-bit counter preceded by a 12-bit prescaler
counter. If not cleared by software, the COP counter overflows and generates an
asynchronous reset after 218 – 24 or 213 – 24 CGMXCLK cycles, depending on the
state of the COP rate select bit, COPRS, in the configuration register. With a
213 – 24 CGMXCLK cycle overflow option, a 4.9152-MHz crystal gives a COP
timeout period of 53.3 ms. Writing any value to location $FFFF before an overflow
occurs prevents a COP reset by clearing the COP counter and stages 12–5 of the
prescaler.
Freescale Semiconductor, Inc...
NOTE:
Service the COP immediately after reset and before entering or after exiting stop
mode to guarantee the maximum time before the first COP counter overflow.
A COP reset pulls the RST pin low for 32 CGMXCLK cycles and sets the COP bit
in the reset status register (RSR).
In monitor mode, the COP is disabled if the RST pin or the IRQ1 is held at VTST.
During the break state, VTST on the RST pin disables the COP.
NOTE:
Place COP clearing instructions in the main program and not in an interrupt
subroutine. Such an interrupt subroutine could keep the COP from generating a
reset even while the main program is not working properly.
9.3 I/O Signals
The following paragraphs describe the signals shown in Figure 9-1.
9.3.1 CGMXCLK
CGMXCLK is the crystal oscillator output signal. CGMXCLK frequency is equal to
the crystal frequency.
9.3.2 STOP Instruction
The STOP instruction clears the COP prescaler.
9.3.3 COPCTL Write
Writing any value to the COP control register (COPCTL) clears the COP counter
and clears bits 12–5 of the prescaler. Reading the COP control register returns the
low byte of the reset vector. See 9.4 COP Control Register.
9.3.4 Power-On Reset
The power-on reset (POR) circuit clears the COP prescaler 4096 CGMXCLK
cycles after power-up.
Data Sheet
108
MC68HC908GZ8
Computer Operating Properly (COP) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Computer Operating Properly (COP) Module
COP Control Register
9.3.5 Internal Reset
An internal reset clears the COP prescaler and the COP counter.
9.3.6 Reset Vector Fetch
A reset vector fetch occurs when the vector address appears on the data bus. A
reset vector fetch clears the COP prescaler.
Freescale Semiconductor, Inc...
9.3.7 COPD (COP Disable)
The COPD signal reflects the state of the COP disable bit (COPD) in the
configuration register. See Section 8. Configuration Register (CONFIG).
9.3.8 COPRS (COP Rate Select)
The COPRS signal reflects the state of the COP rate select bit (COPRS) in the
configuration register. See Section 8. Configuration Register (CONFIG).
9.4 COP Control Register
The COP control register (COPCTL) is located at address $FFFF and overlaps the
reset vector. Writing any value to $FFFF clears the COP counter and starts a new
timeout period. Reading location $FFFF returns the low byte of the reset vector.
Address: $FFFF
Bit 7
6
5
4
3
Read:
Low byte of reset vector
Write:
Clear COP counter
Reset:
Unaffected by reset
2
1
Bit 0
Figure 9-2. COP Control Register (COPCTL)
9.5 Interrupts
The COP does not generate central processor unit (CPU) interrupt requests.
9.6 Monitor Mode
When monitor mode is entered with VTST on the IRQ pin, the COP is disabled as
long as VTST remains on the IRQ pin or the RST pin. When monitor mode is
entered by having blank reset vectors and not having VTST on the IRQ pin, the COP
is automatically disabled until a POR occurs.
MC68HC908GZ8
MOTOROLA
Data Sheet
Computer Operating Properly (COP) Module
For More Information On This Product,
Go to: www.freescale.com
109
Freescale Semiconductor, Inc.
Computer Operating Properly (COP) Module
9.7 Low-Power Modes
The WAIT and STOP instructions put the microcontroller unit (MCU) in low
power-consumption standby modes.
9.7.1 Wait Mode
The COP remains active during wait mode. If COP is enabled, a reset will occur at
COP timeout.
Freescale Semiconductor, Inc...
9.7.2 Stop Mode
Stop mode turns off the CGMXCLK input to the COP and clears the COP prescaler.
Service the COP immediately before entering or after exiting stop mode to ensure
a full COP timeout period after entering or exiting stop mode.
To prevent inadvertently turning off the COP with a STOP instruction, a
configuration option is available that disables the STOP instruction. When the
STOP bit in the configuration register has the STOP instruction disabled, execution
of a STOP instruction results in an illegal opcode reset.
9.8 COP Module During Break Mode
The COP is disabled during a break interrupt when VTST is present on the RST pin.
Data Sheet
110
MC68HC908GZ8
Computer Operating Properly (COP) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 10. Central Processor Unit (CPU)
Freescale Semiconductor, Inc...
10.1 Introduction
The M68HC08 CPU (central processor unit) is an enhanced and fully
object-code-compatible version of the M68HC05 CPU. The CPU08 Reference
Manual (Motorola document order number CPU08RM/AD) contains a description
of the CPU instruction set, addressing modes, and architecture.
10.2 Features
Features of the CPU include:
•
Object code fully upward-compatible with M68HC05 Family
•
16-bit stack pointer with stack manipulation instructions
•
16-bit index register with x-register manipulation instructions
•
8-MHz CPU internal bus frequency
•
64-Kbyte program/data memory space
•
16 addressing modes
•
Memory-to-memory data moves without using accumulator
•
Fast 8-bit by 8-bit multiply and 16-bit by 8-bit divide instructions
•
Enhanced binary-coded decimal (BCD) data handling
•
Modular architecture with expandable internal bus definition for extension of
addressing range beyond 64 Kbytes
•
Low-power stop and wait modes
MC68HC908GZ8
MOTOROLA
Data Sheet
Central Processor Unit (CPU)
For More Information On This Product,
Go to: www.freescale.com
111
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
10.3 CPU Registers
Figure 10-1 shows the five CPU registers. CPU registers are not part of the
memory map.
0
7
ACCUMULATOR (A)
0
15
H
X
INDEX REGISTER (H:X)
15
0
Freescale Semiconductor, Inc...
STACK POINTER (SP)
15
0
PROGRAM COUNTER (PC)
7
0
V 1 1 H I N Z C
CONDITION CODE REGISTER (CCR)
CARRY/BORROW FLAG
ZERO FLAG
NEGATIVE FLAG
INTERRUPT MASK
HALF-CARRY FLAG
TWO’S COMPLEMENT OVERFLOW FLAG
Figure 10-1. CPU Registers
10.3.1 Accumulator
The accumulator is a general-purpose 8-bit register. The CPU uses the
accumulator to hold operands and the results of arithmetic/logic operations.
Bit 7
6
5
4
3
2
1
Bit 0
Read:
Write:
Reset:
Unaffected by reset
Figure 10-2. Accumulator (A)
Data Sheet
112
MC68HC908GZ8
Central Processor Unit (CPU)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
CPU Registers
10.3.2 Index Register
The 16-bit index register allows indexed addressing of a 64-Kbyte memory space.
H is the upper byte of the index register, and X is the lower byte. H:X is the
concatenated 16-bit index register.
In the indexed addressing modes, the CPU uses the contents of the index register
to determine the conditional address of the operand.
Freescale Semiconductor, Inc...
The index register can serve also as a temporary data storage location.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Bit
0
0
0
0
0
0
0
0
0
X
X
X
X
X
X
X
X
Read:
Write:
Reset:
X = Indeterminate
Figure 10-3. Index Register (H:X)
10.3.3 Stack Pointer
The stack pointer is a 16-bit register that contains the address of the next location
on the stack. During a reset, the stack pointer is preset to $00FF. The reset stack
pointer (RSP) instruction sets the least significant byte to $FF and does not affect
the most significant byte. The stack pointer decrements as data is pushed onto the
stack and increments as data is pulled from the stack.
In the stack pointer 8-bit offset and 16-bit offset addressing modes, the stack
pointer can function as an index register to access data on the stack. The CPU
uses the contents of the stack pointer to determine the conditional address of the
operand.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
1
Bit
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
Read:
Write:
Reset:
Figure 10-4. Stack Pointer (SP)
NOTE:
The location of the stack is arbitrary and may be relocated anywhere in
random-access memory (RAM). Moving the SP out of page 0 ($0000 to $00FF)
frees direct address (page 0) space. For correct operation, the stack pointer must
point only to RAM locations.
MC68HC908GZ8
MOTOROLA
Data Sheet
Central Processor Unit (CPU)
For More Information On This Product,
Go to: www.freescale.com
113
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
10.3.4 Program Counter
The program counter is a 16-bit register that contains the address of the next
instruction or operand to be fetched.
Freescale Semiconductor, Inc...
Normally, the program counter automatically increments to the next sequential
memory location every time an instruction or operand is fetched. Jump, branch,
and interrupt operations load the program counter with an address other than that
of the next sequential location.
During reset, the program counter is loaded with the reset vector address located
at $FFFE and $FFFF. The vector address is the address of the first instruction to
be executed after exiting the reset state.
Bit
15
14
13
12
11
10
9
8
7
6
5
4
3
2
Bit
0
1
Read:
Write:
Reset:
Loaded with vector from $FFFE and $FFFF
Figure 10-5. Program Counter (PC)
10.3.5 Condition Code Register
The 8-bit condition code register contains the interrupt mask and five flags that
indicate the results of the instruction just executed. Bits 6 and 5 are set
permanently to logic 1. The following paragraphs describe the functions of the
condition code register.
Bit 7
6
5
4
3
2
1
Bit 0
V
1
1
H
I
N
Z
C
X
1
1
X
1
X
X
X
Read:
Write:
Reset:
X = Indeterminate
Figure 10-6. Condition Code Register (CCR)
V — Overflow Flag
The CPU sets the overflow flag when a two's complement overflow occurs. The
signed branch instructions BGT, BGE, BLE, and BLT use the overflow flag.
1 = Overflow
0 = No overflow
Data Sheet
114
MC68HC908GZ8
Central Processor Unit (CPU)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
CPU Registers
H — Half-Carry Flag
The CPU sets the half-carry flag when a carry occurs between accumulator bits
3 and 4 during an add-without-carry (ADD) or add-with-carry (ADC) operation.
The half-carry flag is required for binary-coded decimal (BCD) arithmetic
operations. The DAA instruction uses the states of the H and C flags to
determine the appropriate correction factor.
1 = Carry between bits 3 and 4
0 = No carry between bits 3 and 4
Freescale Semiconductor, Inc...
I — Interrupt Mask
When the interrupt mask is set, all maskable CPU interrupts are disabled. CPU
interrupts are enabled when the interrupt mask is cleared. When a CPU
interrupt occurs, the interrupt mask is set
automatically after the CPU registers are saved on the stack, but before the
interrupt vector is fetched.
1 = Interrupts disabled
0 = Interrupts enabled
NOTE:
To maintain M6805 Family compatibility, the upper byte of the index register (H) is
not stacked automatically. If the interrupt service routine modifies H, then the user
must stack and unstack H using the PSHH and PULH instructions.
After the I bit is cleared, the highest-priority interrupt request is serviced first.
A return-from-interrupt (RTI) instruction pulls the CPU registers from the stack
and restores the interrupt mask from the stack. After any reset, the interrupt
mask is set and can be cleared only by the clear interrupt mask software
instruction (CLI).
N — Negative flag
The CPU sets the negative flag when an arithmetic operation, logic operation,
or data manipulation produces a negative result, setting bit 7 of the result.
1 = Negative result
0 = Non-negative result
Z — Zero flag
The CPU sets the zero flag when an arithmetic operation, logic operation, or
data manipulation produces a result of $00.
1 = Zero result
0 = Non-zero result
C — Carry/Borrow Flag
The CPU sets the carry/borrow flag when an addition operation produces a
carry out of bit 7 of the accumulator or when a subtraction operation requires a
borrow. Some instructions — such as bit test and branch, shift, and rotate —
also clear or set the carry/borrow flag.
1 = Carry out of bit 7
0 = No carry out of bit 7
MC68HC908GZ8
MOTOROLA
Data Sheet
Central Processor Unit (CPU)
For More Information On This Product,
Go to: www.freescale.com
115
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
10.4 Arithmetic/Logic Unit (ALU)
The ALU performs the arithmetic and logic operations defined by the instruction
set.
Refer to the CPU08 Reference Manual (Motorola document order number
CPU08RM/AD) for a description of the instructions and addressing modes and
more detail about the architecture of the CPU.
Freescale Semiconductor, Inc...
10.5 Low-Power Modes
The WAIT and STOP instructions put the MCU in low power-consumption standby
modes.
10.5.1 Wait Mode
The WAIT instruction:
•
Clears the interrupt mask (I bit) in the condition code register, enabling
interrupts. After exit from wait mode by interrupt, the I bit remains clear. After
exit by reset, the I bit is set.
•
Disables the CPU clock
10.5.2 Stop Mode
The STOP instruction:
•
Clears the interrupt mask (I bit) in the condition code register, enabling
external interrupts. After exit from stop mode by external interrupt, the I bit
remains clear. After exit by reset, the I bit is set.
•
Disables the CPU clock
After exiting stop mode, the CPU clock begins running after the oscillator
stabilization delay.
10.6 CPU During Break Interrupts
If a break module is present on the MCU, the CPU starts a break interrupt by:
•
Loading the instruction register with the SWI instruction
•
Loading the program counter with $FFFC:$FFFD or with $FEFC:$FEFD in
monitor mode
The break interrupt begins after completion of the CPU instruction in progress. If
the break address register match occurs on the last cycle of a CPU instruction, the
break interrupt begins immediately.
A return-from-interrupt instruction (RTI) in the break routine ends the break
interrupt and returns the MCU to normal operation if the break interrupt has been
deasserted.
Data Sheet
116
MC68HC908GZ8
Central Processor Unit (CPU)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
Instruction Set Summary
10.7 Instruction Set Summary
Table 10-1 provides a summary of the M68HC08 instruction set.
Freescale Semiconductor, Inc...
ADC #opr
ADC opr
ADC opr
ADC opr,X
ADC opr,X
ADC ,X
ADC opr,SP
ADC opr,SP
V H I N Z C
A ← (A) + (M) + (C)
Add with Carry
IMM
DIR
EXT
IX2
– IX1
IX
SP1
SP2
A9
B9
C9
D9
E9
F9
9EE9
9ED9
ii
dd
hh ll
ee ff
ff
IMM
DIR
EXT
IX2
– IX1
IX
SP1
SP2
AB
BB
CB
DB
EB
FB
9EEB
9EDB
ii
dd
hh ll
ee ff
ff
ff
ee ff
A7
ii
2
– – – – – – IMM
AF
ii
2
IMM
DIR
EXT
IX2
0 – – –
IX1
IX
SP1
SP2
A4
B4
C4
D4
E4
F4
9EE4
9ED4
ii
dd
hh ll
ee ff
ff
2
3
4
4
3
2
4
5
0
DIR
INH
INH
– – IX1
IX
SP1
38 dd
48
58
68 ff
78
9E68 ff
4
1
1
4
3
5
C
DIR
INH
INH
– – IX1
IX
SP1
37 dd
47
57
67 ff
77
9E67 ff
4
1
1
4
3
5
Add without Carry
AIS #opr
Add Immediate Value (Signed) to SP
SP ← (SP) + (16 « M)
– – – – – – IMM
AIX #opr
Add Immediate Value (Signed) to H:X
H:X ← (H:X) + (16 « M)
A ← (A) & (M)
ASL opr
ASLA
ASLX
ASL opr,X
ASL ,X
ASL opr,SP
A ← (A) + (M)
Logical AND
Arithmetic Shift Left
(Same as LSL)
C
b7
ASR opr
ASRA
ASRX
ASR opr,X
ASR opr,X
ASR opr,SP
Arithmetic Shift Right
BCC rel
Branch if Carry Bit Clear
b0
b7
2
3
4
4
3
2
4
5
2
3
4
4
3
2
4
5
ADD #opr
ADD opr
ADD opr
ADD opr,X
ADD opr,X
ADD ,X
ADD opr,SP
ADD opr,SP
AND #opr
AND opr
AND opr
AND opr,X
AND opr,X
AND ,X
AND opr,SP
AND opr,SP
ff
ee ff
Cycles
Description
Operand
Operation
Effect
on CCR
Opcode
Source
Form
Address
Mode
Table 10-1. Instruction Set Summary (Sheet 1 of 7)
b0
PC ← (PC) + 2 + rel ? (C) = 0
Mn ← 0
ff
ee ff
– – – – – – REL
24
rr
3
DIR (b0)
DIR (b1)
DIR (b2)
– – – – – – DIR (b3)
DIR (b4)
DIR (b5)
DIR (b6)
DIR (b7)
11
13
15
17
19
1B
1D
1F
dd
dd
dd
dd
dd
dd
dd
dd
4
4
4
4
4
4
4
4
BCLR n, opr
Clear Bit n in M
BCS rel
Branch if Carry Bit Set (Same as BLO)
PC ← (PC) + 2 + rel ? (C) = 1
– – – – – – REL
25
rr
3
BEQ rel
Branch if Equal
PC ← (PC) + 2 + rel ? (Z) = 1
– – – – – – REL
27
rr
3
MC68HC908GZ8
MOTOROLA
Data Sheet
Central Processor Unit (CPU)
For More Information On This Product,
Go to: www.freescale.com
117
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
Freescale Semiconductor, Inc...
V H I N Z C
BGE opr
Branch if Greater Than or Equal To
(Signed Operands)
BGT opr
Branch if Greater Than (Signed
Operands)
BHCC rel
Branch if Half Carry Bit Clear
PC ← (PC) + 2 + rel ? (H) = 0
BHCS rel
Branch if Half Carry Bit Set
BHI rel
Branch if Higher
BHS rel
PC ← (PC) + 2 + rel ? (N ⊕ V) = 0
Cycles
Description
Operand
Operation
Effect
on CCR
Opcode
Source
Form
Address
Mode
Table 10-1. Instruction Set Summary (Sheet 2 of 7)
– – – – – – REL
90
rr
3
PC ← (PC) + 2 + rel ? (Z) | (N ⊕ V) = 0 – – – – – – REL
92
rr
3
– – – – – – REL
28
rr
3
PC ← (PC) + 2 + rel ? (H) = 1
– – – – – – REL
29
rr
PC ← (PC) + 2 + rel ? (C) | (Z) = 0
– – – – – – REL
22
rr
3
Branch if Higher or Same
(Same as BCC)
PC ← (PC) + 2 + rel ? (C) = 0
– – – – – – REL
24
rr
3
BIH rel
Branch if IRQ Pin High
PC ← (PC) + 2 + rel ? IRQ = 1
– – – – – – REL
2F
rr
3
BIL rel
Branch if IRQ Pin Low
PC ← (PC) + 2 + rel ? IRQ = 0
– – – – – – REL
2E
rr
3
(A) & (M)
IMM
DIR
EXT
0 – – – IX2
IX1
IX
SP1
SP2
A5
B5
C5
D5
E5
F5
9EE5
9ED5
ii
dd
hh ll
ee ff
ff
ff
ee ff
2
3
4
4
3
2
4
5
93
rr
3
BIT #opr
BIT opr
BIT opr
BIT opr,X
BIT opr,X
BIT ,X
BIT opr,SP
BIT opr,SP
Bit Test
BLE opr
Branch if Less Than or Equal To
(Signed Operands)
BLO rel
Branch if Lower (Same as BCS)
BLS rel
PC ← (PC) + 2 + rel ? (Z) | (N ⊕ V) = 1 – – – – – – REL
3
PC ← (PC) + 2 + rel ? (C) = 1
– – – – – – REL
25
rr
3
Branch if Lower or Same
PC ← (PC) + 2 + rel ? (C) | (Z) = 1
– – – – – – REL
23
rr
3
BLT opr
Branch if Less Than (Signed Operands)
PC ← (PC) + 2 + rel ? (N ⊕ V) =1
– – – – – – REL
91
rr
3
BMC rel
Branch if Interrupt Mask Clear
PC ← (PC) + 2 + rel ? (I) = 0
– – – – – – REL
2C
rr
3
BMI rel
Branch if Minus
PC ← (PC) + 2 + rel ? (N) = 1
– – – – – – REL
2B
rr
3
BMS rel
Branch if Interrupt Mask Set
PC ← (PC) + 2 + rel ? (I) = 1
– – – – – – REL
2D
rr
3
BNE rel
Branch if Not Equal
PC ← (PC) + 2 + rel ? (Z) = 0
– – – – – – REL
26
rr
3
BPL rel
Branch if Plus
PC ← (PC) + 2 + rel ? (N) = 0
– – – – – – REL
2A
rr
3
BRA rel
Branch Always
PC ← (PC) + 2 + rel
– – – – – – REL
20
rr
3
DIR (b0)
DIR (b1)
DIR (b2)
DIR (b3)
– – – – – DIR (b4)
DIR (b5)
DIR (b6)
DIR (b7)
01
03
05
07
09
0B
0D
0F
dd rr
dd rr
dd rr
dd rr
dd rr
dd rr
dd rr
dd rr
5
5
5
5
5
5
5
5
– – – – – – REL
21
rr
3
BRCLR n,opr,rel Branch if Bit n in M Clear
BRN rel
Branch Never
PC ← (PC) + 3 + rel ? (Mn) = 0
PC ← (PC) + 2
Data Sheet
118
MC68HC908GZ8
Central Processor Unit (CPU)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
Instruction Set Summary
00
02
04
06
08
0A
0C
0E
dd rr
dd rr
dd rr
dd rr
dd rr
dd rr
dd rr
dd rr
5
5
5
5
5
5
5
5
Mn ← 1
DIR (b0)
DIR (b1)
DIR (b2)
DIR (b3)
– – – – – – DIR (b4)
DIR (b5)
DIR (b6)
DIR (b7)
10
12
14
16
18
1A
1C
1E
dd
dd
dd
dd
dd
dd
dd
dd
4
4
4
4
4
4
4
4
BSET n,opr
Set Bit n in M
BSR rel
Branch to Subroutine
PC ← (PC) + 2; push (PCL)
SP ← (SP) – 1; push (PCH)
SP ← (SP) – 1
PC ← (PC) + rel
– – – – – – REL
AD
rr
4
CBEQ opr,rel
CBEQA #opr,rel
CBEQX #opr,rel Compare and Branch if Equal
CBEQ opr,X+,rel
CBEQ X+,rel
CBEQ opr,SP,rel
PC ← (PC) + 3 + rel ? (A) – (M) = $00
PC ← (PC) + 3 + rel ? (A) – (M) = $00
PC ← (PC) + 3 + rel ? (X) – (M) = $00
PC ← (PC) + 3 + rel ? (A) – (M) = $00
PC ← (PC) + 2 + rel ? (A) – (M) = $00
PC ← (PC) + 4 + rel ? (A) – (M) = $00
DIR
IMM
– – – – – – IMM
IX1+
IX+
SP1
31
41
51
61
71
9E61
dd rr
ii rr
ii rr
ff rr
rr
ff rr
5
4
4
5
4
6
Cycles
PC ← (PC) + 3 + rel ? (Mn) = 1
DIR (b0)
DIR (b1)
DIR (b2)
DIR (b3)
– – – – – DIR (b4)
DIR (b5)
DIR (b6)
DIR (b7)
Description
V H I N Z C
BRSET n,opr,rel Branch if Bit n in M Set
Freescale Semiconductor, Inc...
Operand
Operation
Effect
on CCR
Address
Mode
Source
Form
Opcode
Table 10-1. Instruction Set Summary (Sheet 3 of 7)
CLC
Clear Carry Bit
C←0
– – – – – 0 INH
98
1
CLI
Clear Interrupt Mask
I←0
– – 0 – – – INH
9A
2
M ← $00
A ← $00
X ← $00
H ← $00
M ← $00
M ← $00
M ← $00
DIR
INH
INH
0 – – 0 1 – INH
IX1
IX
SP1
3F dd
4F
5F
8C
6F ff
7F
9E6F ff
(A) – (M)
IMM
DIR
EXT
IX2
– – IX1
IX
SP1
SP2
A1
B1
C1
D1
E1
F1
9EE1
9ED1
M ← (M) = $FF – (M)
A ← (A) = $FF – (M)
X ← (X) = $FF – (M)
M ← (M) = $FF – (M)
M ← (M) = $FF – (M)
M ← (M) = $FF – (M)
DIR
INH
INH
0 – – 1 IX1
IX
SP1
33 dd
43
53
63 ff
73
9E63 ff
(H:X) – (M:M + 1)
– – IMM
DIR
CLR opr
CLRA
CLRX
CLRH
CLR opr,X
CLR ,X
CLR opr,SP
CMP #opr
CMP opr
CMP opr
CMP opr,X
CMP opr,X
CMP ,X
CMP opr,SP
CMP opr,SP
Clear
Compare A with M
COM opr
COMA
COMX
COM opr,X
COM ,X
COM opr,SP
Complement (One’s Complement)
CPHX #opr
CPHX opr
Compare H:X with M
MC68HC908GZ8
MOTOROLA
65
75
ii
dd
hh ll
ee ff
ff
ff
ee ff
ii ii+1
dd
3
1
1
1
3
2
4
2
3
4
4
3
2
4
5
4
1
1
4
3
5
3
4
Data Sheet
Central Processor Unit (CPU)
For More Information On This Product,
Go to: www.freescale.com
119
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
Freescale Semiconductor, Inc...
Compare X with M
DAA
Decimal Adjust A
(X) – (M)
(A)10
DBNZ opr,rel
DBNZA rel
DBNZX rel
Decrement and Branch if Not Zero
DBNZ opr,X,rel
DBNZ X,rel
DBNZ opr,SP,rel
DEC opr
DECA
DECX
DEC opr,X
DEC ,X
DEC opr,SP
Decrement
DIV
Divide
INC opr
INCA
INCX
INC opr,X
INC ,X
INC opr,SP
JMP opr
JMP opr
JMP opr,X
JMP opr,X
JMP ,X
JSR opr
JSR opr
JSR opr,X
JSR opr,X
JSR ,X
LDA #opr
LDA opr
LDA opr
LDA opr,X
LDA opr,X
LDA ,X
LDA opr,SP
LDA opr,SP
Exclusive OR M with A
Increment
Jump
Jump to Subroutine
Load A from M
IMM
DIR
EXT
IX2
– – IX1
IX
SP1
SP2
A3
B3
C3
D3
E3
F3
9EE3
9ED3
U – – INH
72
A ← (A) – 1 or M ← (M) – 1 or X ← (X) – 1
PC ← (PC) + 3 + rel ? (result) ≠ 0
DIR
PC ← (PC) + 2 + rel ? (result) ≠ 0
INH
PC ← (PC) + 2 + rel ? (result) ≠ 0
– – – – – – INH
PC ← (PC) + 3 + rel ? (result) ≠ 0
IX1
PC ← (PC) + 2 + rel ? (result) ≠ 0
IX
PC ← (PC) + 4 + rel ? (result) ≠ 0
SP1
ff
ee ff
2
3
4
4
3
2
4
5
2
dd rr
rr
rr
ff rr
rr
ff rr
5
3
3
5
4
6
M ← (M) – 1
A ← (A) – 1
X ← (X) – 1
M ← (M) – 1
M ← (M) – 1
M ← (M) – 1
DIR
INH
– – – INH
IX1
IX
SP1
A ← (H:A)/(X)
H ← Remainder
– – – – INH
52
A ← (A ⊕ M)
IMM
DIR
EXT
IX2
0 – – –
IX1
IX
SP1
SP2
A8
B8
C8
D8
E8
F8
9EE8
9ED8
M ← (M) + 1
A ← (A) + 1
X ← (X) + 1
M ← (M) + 1
M ← (M) + 1
M ← (M) + 1
DIR
INH
INH
– – – IX1
IX
SP1
3C dd
4C
5C
6C ff
7C
9E6C ff
PC ← Jump Address
DIR
EXT
– – – – – – IX2
IX1
IX
BC
CC
DC
EC
FC
dd
hh ll
ee ff
ff
2
3
4
3
2
PC ← (PC) + n (n = 1, 2, or 3)
Push (PCL); SP ← (SP) – 1
Push (PCH); SP ← (SP) – 1
PC ← Unconditional Address
DIR
EXT
– – – – – – IX2
IX1
IX
BD
CD
DD
ED
FD
dd
hh ll
ee ff
ff
4
5
6
5
4
A ← (M)
IMM
DIR
EXT
0 – – – IX2
IX1
IX
SP1
SP2
A6
B6
C6
D6
E6
F6
9EE6
9ED6
ii
dd
hh ll
ee ff
ff
2
3
4
4
3
2
4
5
Data Sheet
120
3B
4B
5B
6B
7B
9E6B
ii
dd
hh ll
ee ff
ff
Cycles
V H I N Z C
CPX #opr
CPX opr
CPX opr
CPX ,X
CPX opr,X
CPX opr,X
CPX opr,SP
CPX opr,SP
EOR #opr
EOR opr
EOR opr
EOR opr,X
EOR opr,X
EOR ,X
EOR opr,SP
EOR opr,SP
Description
Operand
Operation
Effect
on CCR
Opcode
Source
Form
Address
Mode
Table 10-1. Instruction Set Summary (Sheet 4 of 7)
3A dd
4A
5A
6A ff
7A
9E6A ff
4
1
1
4
3
5
7
ii
dd
hh ll
ee ff
ff
ff
ee ff
ff
ee ff
2
3
4
4
3
2
4
5
4
1
1
4
3
5
MC68HC908GZ8
Central Processor Unit (CPU)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
Instruction Set Summary
Freescale Semiconductor, Inc...
LDHX #opr
LDHX opr
LDX #opr
LDX opr
LDX opr
LDX opr,X
LDX opr,X
LDX ,X
LDX opr,SP
LDX opr,SP
LSL opr
LSLA
LSLX
LSL opr,X
LSL ,X
LSL opr,SP
V H I N Z C
Load H:X from M
H:X ← (M:M + 1)
IMM
0 – – – DIR
45
55
X ← (M)
IMM
DIR
EXT
IX2
0 – – – IX1
IX
SP1
SP2
AE
BE
CE
DE
EE
FE
9EEE
9EDE
0
DIR
INH
– – INH
IX1
IX
SP1
38 dd
48
58
68 ff
78
9E68 ff
4
1
1
4
3
5
C
DIR
INH
INH
– – 0 IX1
IX
SP1
34 dd
44
54
64 ff
74
9E64 ff
4
1
1
4
3
5
Load X from M
Logical Shift Left
(Same as ASL)
LSR opr
LSRA
LSRX
LSR opr,X
LSR ,X
LSR opr,SP
Logical Shift Right
MOV opr,opr
MOV opr,X+
MOV #opr,opr
MOV X+,opr
Move
MUL
Unsigned multiply
Cycles
Description
Operand
Operation
Effect
on CCR
Opcode
Source
Form
Address
Mode
Table 10-1. Instruction Set Summary (Sheet 5 of 7)
C
b7
b0
0
b7
b0
(M)Destination ← (M)Source
H:X ← (H:X) + 1 (IX+D, DIX+)
0 – – –
DD
DIX+
IMD
IX+D
X:A ← (X) × (A)
– 0 – – – 0 INH
M ← –(M) = $00 – (M)
A ← –(A) = $00 – (A)
X ← –(X) = $00 – (X)
M ← –(M) = $00 – (M)
M ← –(M) = $00 – (M)
DIR
INH
INH
– – IX1
IX
SP1
4E
5E
6E
7E
ii jj
dd
3
4
ii
dd
hh ll
ee ff
ff
2
3
4
4
3
2
4
5
ff
ee ff
dd dd
dd
ii dd
dd
42
5
4
4
4
5
30 dd
40
50
60 ff
70
9E60 ff
4
1
1
4
3
5
NEG opr
NEGA
NEGX
NEG opr,X
NEG ,X
NEG opr,SP
Negate (Two’s Complement)
NOP
No Operation
None
– – – – – – INH
9D
1
NSA
Nibble Swap A
A ← (A[3:0]:A[7:4])
– – – – – – INH
62
3
A ← (A) | (M)
IMM
DIR
EXT
IX2
0 – – – IX1
IX
SP1
SP2
AA
BA
CA
DA
EA
FA
9EEA
9EDA
ii
dd
hh ll
ee ff
ff
2
3
4
4
3
2
4
5
ORA #opr
ORA opr
ORA opr
ORA opr,X
ORA opr,X
ORA ,X
ORA opr,SP
ORA opr,SP
Inclusive OR A and M
PSHA
Push A onto Stack
Push (A); SP ← (SP) – 1
– – – – – – INH
87
2
PSHH
Push H onto Stack
Push (H); SP ← (SP) – 1
– – – – – – INH
8B
2
PSHX
Push X onto Stack
Push (X); SP ← (SP) – 1
– – – – – – INH
89
2
PULA
Pull A from Stack
SP ← (SP + 1); Pull (A)
– – – – – – INH
86
2
PULH
Pull H from Stack
SP ← (SP + 1); Pull (H)
– – – – – – INH
8A
2
PULX
Pull X from Stack
SP ← (SP + 1); Pull (X)
– – – – – – INH
88
2
MC68HC908GZ8
MOTOROLA
ff
ee ff
Data Sheet
Central Processor Unit (CPU)
For More Information On This Product,
Go to: www.freescale.com
121
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
Freescale Semiconductor, Inc...
ROL opr
ROLA
ROLX
ROL opr,X
ROL ,X
ROL opr,SP
V H I N Z C
Rotate Left through Carry
C
b7
b0
Cycles
Description
Operand
Operation
Effect
on CCR
Opcode
Source
Form
Address
Mode
Table 10-1. Instruction Set Summary (Sheet 6 of 7)
DIR
INH
– – INH
IX1
IX
SP1
39 dd
49
59
69 ff
79
9E69 ff
4
1
1
4
3
5
DIR
INH
INH
– – IX1
IX
SP1
36 dd
46
56
66 ff
76
9E66 ff
4
1
1
4
3
5
ROR opr
RORA
RORX
ROR opr,X
ROR ,X
ROR opr,SP
Rotate Right through Carry
RSP
Reset Stack Pointer
SP ← $FF
– – – – – – INH
9C
1
RTI
Return from Interrupt
SP ← (SP) + 1; Pull (CCR)
SP ← (SP) + 1; Pull (A)
SP ← (SP) + 1; Pull (X)
SP ← (SP) + 1; Pull (PCH)
SP ← (SP) + 1; Pull (PCL)
INH
80
7
RTS
Return from Subroutine
SP ← SP + 1; Pull (PCH)
SP ← SP + 1; Pull (PCL)
– – – – – – INH
81
4
A ← (A) – (M) – (C)
IMM
DIR
EXT
– – IX2
IX1
IX
SP1
SP2
A2
B2
C2
D2
E2
F2
9EE2
9ED2
C
b7
b0
ii
dd
hh ll
ee ff
ff
2
3
4
4
3
2
4
5
SBC #opr
SBC opr
SBC opr
SBC opr,X
SBC opr,X
SBC ,X
SBC opr,SP
SBC opr,SP
Subtract with Carry
SEC
Set Carry Bit
C←1
– – – – – 1 INH
99
1
SEI
Set Interrupt Mask
I←1
– – 1 – – – INH
9B
2
M ← (A)
DIR
EXT
IX2
0 – – – IX1
IX
SP1
SP2
B7
C7
D7
E7
F7
9EE7
9ED7
(M:M + 1) ← (H:X)
0 – – – DIR
35
I ← 0; Stop Oscillator
– – 0 – – – INH
8E
M ← (X)
DIR
EXT
IX2
0 – – – IX1
IX
SP1
SP2
BF
CF
DF
EF
FF
9EEF
9EDF
dd
hh ll
ee ff
ff
IMM
DIR
EXT
– – IX2
IX1
IX
SP1
SP2
A0
B0
C0
D0
E0
F0
9EE0
9ED0
ii
dd
hh ll
ee ff
ff
STA opr
STA opr
STA opr,X
STA opr,X
STA ,X
STA opr,SP
STA opr,SP
Store A in M
STHX opr
Store H:X in M
STOP
Enable IRQ Pin; Stop Oscillator
STX opr
STX opr
STX opr,X
STX opr,X
STX ,X
STX opr,SP
STX opr,SP
SUB #opr
SUB opr
SUB opr
SUB opr,X
SUB opr,X
SUB ,X
SUB opr,SP
SUB opr,SP
Store X in M
Subtract
A ← (A) – (M)
Data Sheet
122
ff
ee ff
dd
hh ll
ee ff
ff
ff
ee ff
3
4
4
3
2
4
5
dd
4
1
ff
ee ff
ff
ee ff
3
4
4
3
2
4
5
2
3
4
4
3
2
4
5
MC68HC908GZ8
Central Processor Unit (CPU)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
Opcode Map
Freescale Semiconductor, Inc...
V H I N Z C
Cycles
Description
Operand
Operation
Effect
on CCR
Opcode
Source
Form
Address
Mode
Table 10-1. Instruction Set Summary (Sheet 7 of 7)
SWI
Software Interrupt
PC ← (PC) + 1; Push (PCL)
SP ← (SP) – 1; Push (PCH)
SP ← (SP) – 1; Push (X)
SP ← (SP) – 1; Push (A)
SP ← (SP) – 1; Push (CCR)
SP ← (SP) – 1; I ← 1
PCH ← Interrupt Vector High Byte
PCL ← Interrupt Vector Low Byte
TAP
Transfer A to CCR
CCR ← (A)
INH
84
2
TAX
Transfer A to X
X ← (A)
– – – – – – INH
97
1
TPA
Transfer CCR to A
A ← (CCR)
– – – – – – INH
85
1
(A) – $00 or (X) – $00 or (M) – $00
DIR
INH
0 – – – INH
IX1
IX
SP1
H:X ← (SP) + 1
– – – – – – INH
95
2
A ← (X)
– – – – – – INH
9F
1
(SP) ← (H:X) – 1
– – – – – – INH
94
2
TST opr
TSTA
TSTX
TST opr,X
TST ,X
TST opr,SP
Test for Negative or Zero
TSX
Transfer SP to H:X
TXA
Transfer X to A
TXS
Transfer H:X to SP
A
C
CCR
dd
dd rr
DD
DIR
DIX+
ee ff
EXT
ff
H
H
hh ll
I
ii
IMD
IMM
INH
IX
IX+
IX+D
IX1
IX1+
IX2
M
N
Accumulator
Carry/borrow bit
Condition code register
Direct address of operand
Direct address of operand and relative offset of branch instruction
Direct to direct addressing mode
Direct addressing mode
Direct to indexed with post increment addressing mode
High and low bytes of offset in indexed, 16-bit offset addressing
Extended addressing mode
Offset byte in indexed, 8-bit offset addressing
Half-carry bit
Index register high byte
High and low bytes of operand address in extended addressing
Interrupt mask
Immediate operand byte
Immediate source to direct destination addressing mode
Immediate addressing mode
Inherent addressing mode
Indexed, no offset addressing mode
Indexed, no offset, post increment addressing mode
Indexed with post increment to direct addressing mode
Indexed, 8-bit offset addressing mode
Indexed, 8-bit offset, post increment addressing mode
Indexed, 16-bit offset addressing mode
Memory location
Negative bit
n
opr
PC
PCH
PCL
REL
rel
rr
SP1
SP2
SP
U
V
X
Z
&
|
⊕
()
–( )
#
«
←
?
:
—
– – 1 – – – INH
83
9
3D dd
4D
5D
6D ff
7D
9E6D ff
3
1
1
3
2
4
Any bit
Operand (one or two bytes)
Program counter
Program counter high byte
Program counter low byte
Relative addressing mode
Relative program counter offset byte
Relative program counter offset byte
Stack pointer, 8-bit offset addressing mode
Stack pointer 16-bit offset addressing mode
Stack pointer
Undefined
Overflow bit
Index register low byte
Zero bit
Logical AND
Logical OR
Logical EXCLUSIVE OR
Contents of
Negation (two’s complement)
Immediate value
Sign extend
Loaded with
If
Concatenated with
Set or cleared
Not affected
10.8 Opcode Map
See Table 10-2.
MC68HC908GZ8
MOTOROLA
Data Sheet
Central Processor Unit (CPU)
For More Information On This Product,
Go to: www.freescale.com
123
124
Data Sheet
For More Information On This Product,
Go to: www.freescale.com
Central Processor Unit (CPU)
5
BRSET0
3 DIR
5
BRCLR0
3 DIR
5
BRSET1
3 DIR
5
BRCLR1
3 DIR
5
BRSET2
3 DIR
5
BRCLR2
3 DIR
5
BRSET3
3 DIR
5
BRCLR3
3 DIR
5
BRSET4
3 DIR
5
BRCLR4
3 DIR
5
BRSET5
3 DIR
5
BRCLR5
3 DIR
5
BRSET6
3 DIR
5
BRCLR6
3 DIR
5
BRSET7
3 DIR
5
BRCLR7
3 DIR
0
4
BSET0
2 DIR
4
BCLR0
2 DIR
4
BSET1
2 DIR
4
BCLR1
2 DIR
4
BSET2
2 DIR
4
BCLR2
2 DIR
4
BSET3
2 DIR
4
BCLR3
2 DIR
4
BSET4
2 DIR
4
BCLR4
2 DIR
4
BSET5
2 DIR
4
BCLR5
2 DIR
4
BSET6
2 DIR
4
BCLR6
2 DIR
4
BSET7
2 DIR
4
BCLR7
2 DIR
1
3
BRA
2 REL
3
BRN
2 REL
3
BHI
2 REL
3
BLS
2 REL
3
BCC
2 REL
3
BCS
2 REL
3
BNE
2 REL
3
BEQ
2 REL
3
BHCC
2 REL
3
BHCS
2 REL
3
BPL
2 REL
3
BMI
2 REL
3
BMC
2 REL
3
BMS
2 REL
3
BIL
2 REL
3
BIH
2 REL
2
Branch
REL
4
INH
1
NEGX
1 INH
4
CBEQX
3 IMM
7
DIV
1 INH
1
COMX
1 INH
1
LSRX
1 INH
4
LDHX
2 DIR
1
RORX
1 INH
1
ASRX
1 INH
1
LSLX
1 INH
1
ROLX
1 INH
1
DECX
1 INH
3
DBNZX
2 INH
1
INCX
1 INH
1
TSTX
1 INH
4
MOV
2 DIX+
1
CLRX
1 INH
5
4
NEG
2
IX1
5
CBEQ
3 IX1+
3
NSA
1 INH
4
COM
2 IX1
4
LSR
2 IX1
3
CPHX
3 IMM
4
ROR
2 IX1
4
ASR
2 IX1
4
LSL
2 IX1
4
ROL
2 IX1
4
DEC
2 IX1
5
DBNZ
3 IX1
4
INC
2 IX1
3
TST
2 IX1
4
MOV
3 IMD
3
CLR
2 IX1
6
7
IX
9
7
3
RTI
BGE
1 INH 2 REL
4
3
RTS
BLT
1 INH 2 REL
3
BGT
2 REL
9
3
SWI
BLE
1 INH 2 REL
2
2
TAP
TXS
1 INH 1 INH
1
2
TPA
TSX
1 INH 1 INH
2
PULA
1 INH
2
1
PSHA
TAX
1 INH 1 INH
2
1
PULX
CLC
1 INH 1 INH
2
1
PSHX
SEC
1 INH 1 INH
2
2
PULH
CLI
1 INH 1 INH
2
2
PSHH
SEI
1 INH 1 INH
1
1
CLRH
RSP
1 INH 1 INH
1
NOP
1 INH
1
STOP
*
1 INH
1
1
WAIT
TXA
1 INH 1 INH
8
Control
INH
INH
B
DIR
MSB
0
LSB
3
SUB
2 DIR
3
CMP
2 DIR
3
SBC
2 DIR
3
CPX
2 DIR
3
AND
2 DIR
3
BIT
2 DIR
3
LDA
2 DIR
3
STA
2 DIR
3
EOR
2 DIR
3
ADC
2 DIR
3
ORA
2 DIR
3
ADD
2 DIR
2
JMP
2 DIR
4
4
BSR
JSR
2 REL 2 DIR
2
3
LDX
LDX
2 IMM 2 DIR
2
3
AIX
STX
2 IMM 2 DIR
2
SUB
2 IMM
2
CMP
2 IMM
2
SBC
2 IMM
2
CPX
2 IMM
2
AND
2 IMM
2
BIT
2 IMM
2
LDA
2 IMM
2
AIS
2 IMM
2
EOR
2 IMM
2
ADC
2 IMM
2
ORA
2 IMM
2
ADD
2 IMM
A
IMM
Low Byte of Opcode in Hexadecimal
5
3
NEG
NEG
3 SP1 1 IX
6
4
CBEQ
CBEQ
4 SP1 2 IX+
2
DAA
1 INH
5
3
COM
COM
3 SP1 1 IX
5
3
LSR
LSR
3 SP1 1 IX
4
CPHX
2 DIR
5
3
ROR
ROR
3 SP1 1 IX
5
3
ASR
ASR
3 SP1 1 IX
5
3
LSL
LSL
3 SP1 1 IX
5
3
ROL
ROL
3 SP1 1 IX
5
3
DEC
DEC
3 SP1 1 IX
6
4
DBNZ
DBNZ
4 SP1 2 IX
5
3
INC
INC
3 SP1 1 IX
4
2
TST
TST
3 SP1 1 IX
4
MOV
2 IX+D
4
2
CLR
CLR
3 SP1 1 IX
9E6
SP1
Table 10-2. Opcode Map
Read-Modify-Write
INH
IX1
SP1 Stack Pointer, 8-Bit Offset
SP2 Stack Pointer, 16-Bit Offset
IX+ Indexed, No Offset with
Post Increment
IX1+ Indexed, 1-Byte Offset with
Post Increment
4
1
NEG
NEGA
2 DIR 1 INH
5
4
CBEQ CBEQA
3 DIR 3 IMM
5
MUL
1 INH
4
1
COM
COMA
2 DIR 1 INH
4
1
LSR
LSRA
2 DIR 1 INH
4
3
STHX
LDHX
2 DIR 3 IMM
4
1
ROR
RORA
2 DIR 1 INH
4
1
ASR
ASRA
2 DIR 1 INH
4
1
LSL
LSLA
2 DIR 1 INH
4
1
ROL
ROLA
2 DIR 1 INH
4
1
DEC
DECA
2 DIR 1 INH
5
3
DBNZ DBNZA
3 DIR 2 INH
4
1
INC
INCA
2 DIR 1 INH
3
1
TST
TSTA
2 DIR 1 INH
5
MOV
3 DD
3
1
CLR
CLRA
2 DIR 1 INH
3
DIR
INH Inherent
REL Relative
IMM Immediate
IX
Indexed, No Offset
DIR Direct
IX1 Indexed, 8-Bit Offset
EXT Extended
IX2 Indexed, 16-Bit Offset
DD Direct-Direct
IMD Immediate-Direct
IX+D Indexed-Direct DIX+ Direct-Indexed
*Pre-byte for stack pointer indexed instructions
F
E
D
C
B
A
9
8
7
6
5
4
3
2
1
0
LSB
MSB
Bit Manipulation
DIR
DIR
E
3
SUB
2 IX1
3
CMP
2 IX1
3
SBC
2 IX1
3
CPX
2 IX1
3
AND
2 IX1
3
BIT
2 IX1
3
LDA
2 IX1
3
STA
2 IX1
3
EOR
2 IX1
3
ADC
2 IX1
3
ORA
2 IX1
3
ADD
2 IX1
3
JMP
2 IX1
5
JSR
2 IX1
5
3
LDX
LDX
4 SP2 2 IX1
5
3
STX
STX
4 SP2 2 IX1
5
SUB
4 SP2
5
CMP
4 SP2
5
SBC
4 SP2
5
CPX
4 SP2
5
AND
4 SP2
5
BIT
4 SP2
5
LDA
4 SP2
5
STA
4 SP2
5
EOR
4 SP2
5
ADC
4 SP2
5
ORA
4 SP2
5
ADD
4 SP2
9ED
IX1
F
IX
2
SUB
1 IX
2
CMP
1 IX
2
SBC
1 IX
2
CPX
1 IX
2
AND
1 IX
2
BIT
1 IX
2
LDA
1 IX
2
STA
1 IX
2
EOR
1 IX
2
ADC
1 IX
2
ORA
1 IX
2
ADD
1 IX
2
JMP
1 IX
4
JSR
1 IX
4
2
LDX
LDX
3 SP1 1 IX
4
2
STX
STX
3 SP1 1 IX
4
SUB
3 SP1
4
CMP
3 SP1
4
SBC
3 SP1
4
CPX
3 SP1
4
AND
3 SP1
4
BIT
3 SP1
4
LDA
3 SP1
4
STA
3 SP1
4
EOR
3 SP1
4
ADC
3 SP1
4
ORA
3 SP1
4
ADD
3 SP1
9EE
SP1
High Byte of Opcode in Hexadecimal
4
SUB
3 IX2
4
CMP
3 IX2
4
SBC
3 IX2
4
CPX
3 IX2
4
AND
3 IX2
4
BIT
3 IX2
4
LDA
3 IX2
4
STA
3 IX2
4
EOR
3 IX2
4
ADC
3 IX2
4
ORA
3 IX2
4
ADD
3 IX2
4
JMP
3 IX2
6
JSR
3 IX2
4
LDX
3 IX2
4
STX
3 IX2
D
Register/Memory
IX2
SP2
5
Cycles
BRSET0 Opcode Mnemonic
3 DIR Number of Bytes / Addressing Mode
0
4
SUB
3 EXT
4
CMP
3 EXT
4
SBC
3 EXT
4
CPX
3 EXT
4
AND
3 EXT
4
BIT
3 EXT
4
LDA
3 EXT
4
STA
3 EXT
4
EOR
3 EXT
4
ADC
3 EXT
4
ORA
3 EXT
4
ADD
3 EXT
3
JMP
3 EXT
5
JSR
3 EXT
4
LDX
3 EXT
4
STX
3 EXT
C
EXT
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Central Processor Unit (CPU)
MC68HC908GZ8
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 11. FLASH Memory (FLASH)
Freescale Semiconductor, Inc...
11.1 Introduction
This section describes the operation of the embedded FLASH memory. This
memory can be read, programmed, and erased from a single external supply. The
program, erase, and read operations are enabled through the use of an internal
charge pump. It is recommended that the user utilize the FLASH programming
routines provided in the on-chip ROM, which are described more fully in a separate
Motorola application note.
11.2 Functional Description
The FLASH memory is an array of 7936 bytes with an additional 44 bytes of user
vectors and one byte of block protection. An erased bit reads as logic 1 and a
programmed bit reads as a logic 0. Memory in the FLASH array is organized into
two rows per page basis. For the 16-K word by 8-bit embedded FLASH memory,
the page size is 64 bytes per page and the row size is 32 bytes per row. Hence the
minimum erase page size is 64 bytes and the minimum program row size is 32
bytes. Program and erase operation operations are facilitated through control bits
in FLASH control register (FLCR). Details for these operations appear later in this
section.
The address ranges for the user memory and vectors are:
•
$E000–$FDFF; user memory
•
$FE08; FLASH control register
•
$FF7E; FLASH block protect register
•
$FFD4–$FFFF; these locations are reserved for user-defined interrupt and
reset vectors
Programming tools are available from Motorola. Contact your local Motorola
representative for more information.
NOTE:
A security feature prevents viewing of the FLASH contents.(1)
1. No security feature is absolutely secure. However, Motorola’s strategy is to make reading or
copying the FLASH difficult for unauthorized users.
MC68HC908GZ8
MOTOROLA
Data Sheet
FLASH Memory (FLASH)
For More Information On This Product,
Go to: www.freescale.com
125
Freescale Semiconductor, Inc.
FLASH Memory (FLASH)
11.3 FLASH Control Register
The FLASH control register (FLCR) controls FLASH program and erase
operations.
Address:
Read:
$FE08
Bit 7
6
5
4
0
0
0
0
0
0
0
0
Write:
Reset:
3
2
1
Bit 0
HVEN
MASS
ERASE
PGM
0
0
0
0
= Unimplemented
Freescale Semiconductor, Inc...
Figure 11-1. FLASH Control Register (FLCR)
HVEN — High-Voltage Enable Bit
This read/write bit enables the charge pump to drive high voltages for program
and erase operations in the array. HVEN can only be set if either PGM = 1 or
ERASE = 1 and the proper sequence for program or erase is followed.
1 = High voltage enabled to array and charge pump on
0 = High voltage disabled to array and charge pump off
MASS — Mass Erase Control Bit
Setting this read/write bit configures the 16-Kbyte FLASH array for mass erase
operation.
1 = MASS erase operation selected
0 = PAGE erase operation selected
ERASE — Erase Control Bit
This read/write bit configures the memory for erase operation. ERASE is
interlocked with the PGM bit such that both bits cannot be equal to 1 or set to 1
at the same time.
1 = Erase operation selected
0 = Erase operation unselected
PGM — Program Control Bit
This read/write bit configures the memory for program operation. PGM is
interlocked with the ERASE bit such that both bits cannot be equal to 1 or set
to 1 at the same time.
1 = Program operation selected
0 = Program operation unselected
Data Sheet
126
MC68HC908GZ8
FLASH Memory (FLASH)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
FLASH Memory (FLASH)
FLASH Page Erase Operation
11.4 FLASH Page Erase Operation
Freescale Semiconductor, Inc...
Use this step-by-step procedure to erase a page (64 bytes) of FLASH memory to
read as logic 1. A page consists of 64 consecutive bytes starting from addresses
$XX00, $XX40, $XX80, or $XXC0. The 44-byte user interrupt vectors area also
forms a page. Any FLASH memory page can be erased alone.
1. Set the ERASE bit, and clear the MASS bit in the FLASH control register.
2. Read the FLASH block protect register.
3. Write any data to any FLASH address within the page address range
desired.
4. Wait for a time, tNVS (minimum 10 µs)
5. Set the HVEN bit.
6. Wait for a time, tErase (minimum 1 ms or 4 ms)
7. Clear the ERASE bit.
8. Wait for a time, tNVH (minimum 5 µs)
9. Clear the HVEN bit.
10. After a time, tRCV (typical 1 µs), the memory can be accessed again in read
mode.
NOTE:
Programming and erasing of FLASH locations cannot be performed by code being
executed from FLASH memory. While these operations must be performed in the
order shown, other unrelated operations may occur between the steps.
NOTE:
It is highly recommended that interrupts be disabled during program/ erase
operations.
NOTE:
In applications that need more than 1000 program/erase cycles, use the 4-ms page
erase specification to get improved long-term reliability. Any application can use
this 4-ms page erase specification. However, in applications where a FLASH
location will be erased and reprogrammed less than 1000 times, and speed is
important, use the 1-ms page erase specification to get a lower minimum erase
time.
MC68HC908GZ8
MOTOROLA
Data Sheet
FLASH Memory (FLASH)
For More Information On This Product,
Go to: www.freescale.com
127
Freescale Semiconductor, Inc.
FLASH Memory (FLASH)
Freescale Semiconductor, Inc...
11.5 FLASH Mass Erase Operation
Use this step-by-step procedure to erase entire FLASH memory to read as logic 1:
1. Set both the ERASE bit, and the MASS bit in the FLASH control register.
2. Read from the FLASH block protect register.
3. Write any data to any FLASH address(1) within the FLASH memory address
range.
4. Wait for a time, tNVS (minimum 10 µs)
5. Set the HVEN bit.
6. Wait for a time, tMErase (minimum 4 ms)
7. Clear the ERASE and MASS bits.
8. Wait for a time, tNVHL (minimum 100 µs)
9. Clear the HVEN bit.
10. After a time, tRCV (minimum 1 µs), the memory can be accessed again in
read mode.
NOTE:
Mass erase is disabled whenever any block is protected (FLBPR does not equal
$FF).
NOTE:
Programming and erasing of FLASH locations cannot be performed by code being
executed from FLASH memory. While these operations must be performed in the
order shown, other unrelated operations may occur between the steps.
11.6 FLASH Program/Read Operation
Programming of the FLASH memory is done on a row basis. A row consists of 32
consecutive bytes starting from addresses $XX00, $XX20, $XX40, $XX60, $XX80,
$XXA0, $XXC0, and $XXE0.
During the programming cycle, make sure that all addresses being written to fit
within one of the ranges specified above. Attempts to program addresses in
different row ranges in one programming cycle will fail. Use this step-by-step
procedure to program a row of FLASH memory (Figure 11-2 is a flowchart
representation).
NOTE:
Only bytes which are currently $FF may be programmed.
1. Set the PGM bit. This configures the memory for program operation and
enables the latching of address and data for programming.
2. Read from the FLASH block protect register.
3. Write any data to any FLASH address within the row address range desired.
4. Wait for a time, tNVS (minimum 10 µs).
1. When in monitor mode, with security sequence failed (see 15.4 Security), write to the FLASH block
protect register instead of any FLASH address.
Data Sheet
128
MC68HC908GZ8
FLASH Memory (FLASH)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
FLASH Memory (FLASH)
FLASH Program/Read Operation
Freescale Semiconductor, Inc...
5.
6.
7.
8.
9.
10.
11.
12.
13.
Set the HVEN bit.
Wait for a time, tPGS (minimum 5 µs).
Write data to the FLASH address to be programmed.
Wait for a time, tPROG (30–40 µs).
Repeat step 7 and 8 until all the bytes within the row are programmed.
Clear the PGM bit.(1)
Wait for a time, tNVH (minimum 5 µs).
Clear the HVEN bit.
After time, tRCV (minimum 1 µs), the memory can be accessed in read mode
again.
This program sequence is repeated throughout the memory until all data is
programmed.
NOTE:
Programming and erasing of FLASH locations can not be performed by code being
executed from the same FLASH array.
NOTE:
While these operations must be performed in the order shown, other unrelated
operations may occur between the steps. Care must be taken within the FLASH
array memory space such as the COP control register (COPCTL) at $FFFF.
NOTE:
It is highly recommended that interrupts be disabled during program/ erase
operations.
NOTE:
Do not exceed tPROG maximum or tHV maximum. tHV is defined as the cumulative
high voltage programming time to the same row before next erase. tHV must satisfy
this condition:
tNVS + tNVH + tPGS + (tPROG x 32) ≤ tHV maximum
Refer to 24.15 Memory Characteristics.
NOTE:
The time between programming the FLASH address change (step 7 to step 7), or
the time between the last FLASH programmed to clearing the PGM bit (step 7 to
step 10) must not exceed the maximum programming time, tPROG maximum.
CAUTION:
Be cautious when programming the FLASH array to ensure that non-FLASH
locations are not used as the address that is written to when selecting either the
desired row address range in step 3 of the algorithm or the byte to be programmed
in step 7 of the algorithm. This applies particularly to $FFD4–$FFDF.
MC68HC908GZ8
MOTOROLA
Data Sheet
FLASH Memory (FLASH)
For More Information On This Product,
Go to: www.freescale.com
129
Freescale Semiconductor, Inc.
FLASH Memory (FLASH)
Algorithm for programming
a row (32 bytes) of FLASH memory
1
2
3
SET PGM BIT
READ THE FLASH BLOCK PROTECT REGISTER
WRITE ANY DATA TO ANY FLASH ADDRESS
WITHIN THE ROW ADDRESS RANGE DESIRED
Freescale Semiconductor, Inc...
4
WAIT FOR A TIME, tNVS
5
SET HVEN BIT
6
WAIT FOR A TIME, tPGS
7
WRITE DATA TO THE FLASH ADDRESS
TO BE PROGRAMMED
8
WAIT FOR A TIME, tPROG
COMPLETED
PROGRAMMING
THIS ROW?
Y
N
10
11
CLEAR PGM BIT
WAIT FOR A TIME, tNVH
Note:
The time between each FLASH address change (step 7 to step 7),
or the time between the last FLASH address programmed
to clearing PGM bit (step 7 to step 10)
must not exceed the maximum programming
time, tPROG max.
12
13
This row program algorithm assumes the row/s
to be programmed are initially erased.
CLEAR HVEN BIT
WAIT FOR A TIME, tRCV
END OF PROGRAMMING
Figure 11-2. FLASH Programming Flowchart
Data Sheet
130
MC68HC908GZ8
FLASH Memory (FLASH)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
FLASH Memory (FLASH)
FLASH Block Protection
11.7 FLASH Block Protection
Due to the ability of the on-board charge pump to erase and program the FLASH
memory in the target application, provision is made for protecting a block of
memory from unintentional erase or program operations due to system
malfunction. This protection is done by using of a FLASH block protect register
(FLBPR). The FLBPR determines the range of the FLASH memory which is to be
protected. The range of the protected area starts from a location defined by FLBPR
and ends at the bottom of the FLASH memory ($FFFF). When the memory is
protected, the HVEN bit cannot be set in either ERASE or PROGRAM operations.
Freescale Semiconductor, Inc...
NOTE:
In performing a program or erase operation, the FLASH block protect register must
be read after setting the PGM or ERASE bit and before asserting the HVEN bit
When the FLBPR is program with all 0’s, the entire memory is protected from being
programmed and erased. When all the bits are erased (all 1’s), the entire memory
is accessible for program and erase.
When bits within the FLBPR are programmed, they lock a block of memory,
address ranges as shown in 11.7.1 FLASH Block Protect Register. Once the
FLBPR is programmed with a value other than $FF, any erase or program of the
FLBPR or the protected block of FLASH memory is prohibited. The presence of a
VTST on the IRQ pin will bypass the block protection so that all of the memory
included in the block protect register is open for program and erase operations.
NOTE:
The FLASH block protect register is not protected with special hardware or
software. Therefore, if this page is not protected by FLBPR the register is erased
by either a page or mass erase operation.
11.7.1 FLASH Block Protect Register
The FLASH block protect register (FLBPR) is implemented as a byte within the
FLASH memory, and therefore can only be written during a programming
sequence of the FLASH memory. The value in this register determines the starting
location of the protected range within the FLASH memory.
Address:
Read:
Write:
Reset:
$FF7E
Bit 7
6
5
4
3
2
1
Bit 0
BPR7
BPR6
BPR5
BPR4
BPR3
BPR2
BPR1
BPR0
U
U
U
U
U
U
U
U
U = Unaffected by reset. Initial value from factory is 1.
Write to this register is by a programming sequence to the FLASH memory.
Figure 11-3. FLASH Block Protect Register (FLBPR)
MC68HC908GZ8
MOTOROLA
Data Sheet
FLASH Memory (FLASH)
For More Information On This Product,
Go to: www.freescale.com
131
Freescale Semiconductor, Inc.
FLASH Memory (FLASH)
BPR[7:0] — FLASH Block Protect Bits
These eight bits represent bits [13:6] of a 16-bit memory address.
Bit-15 and Bit-14 are logic 1s and bits [5:0] are logic 0s.
The resultant 16-bit address is used for specifying the start address of the
FLASH memory for block protection. The FLASH is protected from this start
address to the end of FLASH memory, at $FFFF. With this mechanism, the
protect start address can be $XX00, $XX40, $XX80, and $XXC0 (64 bytes page
boundaries) within the FLASH memory.
16-BIT MEMORY ADDRESS
Freescale Semiconductor, Inc...
START ADDRESS OF FLASH
1
BLOCK PROTECT
1
FLBPR VALUE
0
0
0
0
0
0
Figure 11-4. FLASH Block Protect Start Address
Table 11-1. Examples of Protect Address Ranges
BPR[7:0]
Addresses of Protect Range
$00
The entire FLASH memory is protected.
$01 (0000 0001)
$C040 (1100 0000 0100 0000) — $FFFF
$02 (0000 0010)
$C080 (1100 0000 1000 0000) — $FFFF
$03 (0000 0011)
$C0C0 (1100 0000 1100 0000) — $FFFF
$04 (0000 0100)
$C100 (1100 0001 0000 0000) — $FFFF
and so on...
$FC (1111 1100)
$FF00 (1111 1111 0000 0000) — FFFF
$FD (1111 1101)
$FF40 (1111 1111 0100 0000) — $FFFF
FLBPR and vectors are protected
$FE (1111 1110)
$FF80 (1111 1111 1000 0000) — FFFF
Vectors are protected
$FF
The entire FLASH memory is not protected.
11.8 Wait Mode
Putting the MCU into wait mode while the FLASH is in read mode does not affect
the operation of the FLASH memory directly, but there will not be any memory
activity since the CPU is inactive.
The WAIT instruction should not be executed while performing a program or erase
operation on the FLASH, otherwise the operation will discontinue, and the FLASH
will be on standby mode.
Data Sheet
132
MC68HC908GZ8
FLASH Memory (FLASH)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
FLASH Memory (FLASH)
Stop Mode
11.9 Stop Mode
Putting the MCU into stop mode while the FLASH is in read mode does not affect
the operation of the FLASH memory directly, but there will not be any memory
activity since the CPU is inactive.
The STOP instruction should not be executed while performing a program or erase
operation on the FLASH, otherwise the operation will discontinue, and the FLASH
will be on standby mode
Freescale Semiconductor, Inc...
NOTE:
Standby mode is the power saving mode of the FLASH module in which all internal
control signals to the FLASH are inactive and the current consumption of the
FLASH is at a minimum.
MC68HC908GZ8
MOTOROLA
Data Sheet
FLASH Memory (FLASH)
For More Information On This Product,
Go to: www.freescale.com
133
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
FLASH Memory (FLASH)
Data Sheet
134
MC68HC908GZ8
FLASH Memory (FLASH)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 12. External Interrupt (IRQ)
12.1 Introduction
Freescale Semiconductor, Inc...
The IRQ (external interrupt) module provides a maskable interrupt input.
12.2 Features
Features of the IRQ module include:
•
A dedicated external interrupt pin (IRQ)
•
IRQ interrupt control bits
•
Hysteresis buffer
•
Programmable edge-only or edge and level interrupt sensitivity
•
Automatic interrupt acknowledge
•
Internal pullup resistor
12.3 Functional Description
A logic 0 applied to the external interrupt pin can latch a central processor unit
(CPU) interrupt request. Figure 12-1 shows the structure of the IRQ module.
Interrupt signals on the IRQ pin are latched into the IRQ latch. An interrupt latch
remains set until one of the following actions occurs:
•
Vector fetch — A vector fetch automatically generates an interrupt
acknowledge signal that clears the latch that caused the vector fetch.
•
Software clear — Software can clear an interrupt latch by writing to the
appropriate acknowledge bit in the interrupt status and control register
(INTSCR). Writing a logic 1 to the ACK bit clears the IRQ latch.
•
Reset — A reset automatically clears the interrupt latch.
The external interrupt pin is falling-edge triggered and is software-configurable to
be either falling-edge or falling-edge and low-level triggered. The MODE bit in the
INTSCR controls the triggering sensitivity of the IRQ pin.
When an interrupt pin is edge-triggered only, the interrupt remains set until a vector
fetch, software clear, or reset occurs.
MC68HC908GZ8
MOTOROLA
Data Sheet
External Interrupt (IRQ)
For More Information On This Product,
Go to: www.freescale.com
135
Freescale Semiconductor, Inc.
External Interrupt (IRQ)
RESET
INTERNAL ADDRESS BUS
ACK
TO CPU FOR
BIL/BIH
INSTRUCTIONS
VECTOR
FETCH
DECODER
VDD
INTERNAL
PULLUP
DEVICE
VDD
IRQF
D
CLR
Q
IRQ
INTERRUPT
REQUEST
SYNCHRONIZER
CK
Freescale Semiconductor, Inc...
IRQ
IMASK
MODE
TO MODE
SELECT
LOGIC
HIGH
VOLTAGE
DETECT
Figure 12-1. IRQ Module Block Diagram
When an interrupt pin is both falling-edge and low-level triggered, the interrupt
remains set until both of these events occur:
•
Vector fetch or software clear
•
Return of the interrupt pin to logic 1
The vector fetch or software clear may occur before or after the interrupt pin returns
to logic 1. As long as the pin is low, the interrupt request remains pending. A reset
will clear the latch and the MODE control bit, thereby clearing the interrupt even if
the pin stays low.
When set, the IMASK bit in the INTSCR mask all external interrupt requests. A
latched interrupt request is not presented to the interrupt priority logic unless the
IMASK bit is clear.
NOTE:
Addr.
The interrupt mask (I) in the condition code register (CCR) masks all interrupt
requests, including external interrupt requests.
Register Name
Bit 7
6
5
4
3
2
IRQ Status and Control Reg- Read:
$001D
ister (INTSCR) Write:
See page 138. Reset:
0
0
0
0
IRQF
0
ACK
0
0
0
0
0
0
1
Bit 0
IMASK
MODE
0
0
= Unimplemented
Figure 12-2. IRQ I/O Register Summary
Data Sheet
136
MC68HC908GZ8
External Interrupt (IRQ)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
External Interrupt (IRQ)
IRQ Pin
12.4 IRQ Pin
A logic 0 on the IRQ pin can latch an interrupt request into the IRQ latch. A vector
fetch, software clear, or reset clears the IRQ latch.
Freescale Semiconductor, Inc...
If the MODE bit is set, the IRQ pin is both falling-edge-sensitive and
low-level-sensitive. With MODE set, both of the following actions must occur to
clear IRQ:
•
Vector fetch or software clear — A vector fetch generates an interrupt
acknowledge signal to clear the latch. Software may generate the interrupt
acknowledge signal by writing a logic 1 to the ACK bit in the interrupt status
and control register (INTSCR). The ACK bit is useful in applications that poll
the IRQ pin and require software to clear the IRQ latch. Writing to the ACK
bit prior to leaving an interrupt service routine can also prevent spurious
interrupts due to noise. Setting ACK does not affect subsequent transitions
on the IRQ pin. A falling edge that occurs after writing to the ACK bit another
interrupt request. If the IRQ mask bit, IMASK, is clear, the CPU loads the
program counter with the vector address at locations $FFFA and $FFFB.
•
Return of the IRQ pin to logic 1 — As long as the IRQ pin is at logic 0, IRQ
remains active.
The vector fetch or software clear and the return of the IRQ pin to logic 1 may occur
in any order. The interrupt request remains pending as long as the IRQ pin is at
logic 0. A reset will clear the latch and the MODE control bit, thereby clearing the
interrupt even if the pin stays low.
If the MODE bit is clear, the IRQ pin is falling-edge-sensitive only. With MODE
clear, a vector fetch or software clear immediately clears the IRQ latch.
The IRQF bit in the INTSCR register can be used to check for pending interrupts.
The IRQF bit is not affected by the IMASK bit, which makes it useful in applications
where polling is preferred.
Use the BIH or BIL instruction to read the logic level on the IRQ pin.
NOTE:
When using the level-sensitive interrupt trigger, avoid false interrupts by masking
interrupt requests in the interrupt routine.
12.5 IRQ Module During Break Interrupts
The BCFE bit in the SIM break flag control register (SBFCR) enables software to
clear the latch during the break state. See Section 6. Break Module (BRK).
To allow software to clear the IRQ latch during a break interrupt, write a logic 1 to
the BCFE bit. If a latch is cleared during the break state, it remains cleared when
the MCU exits the break state.
MC68HC908GZ8
MOTOROLA
Data Sheet
External Interrupt (IRQ)
For More Information On This Product,
Go to: www.freescale.com
137
Freescale Semiconductor, Inc.
External Interrupt (IRQ)
To protect CPU interrupt flags during the break state, write a logic 0 to the BCFE
bit. With BCFE at logic 0 (its default state), writing to the ACK bit in the IRQ status
and control register during the break state has no effect on the IRQ interrupt flags.
12.6 IRQ Status and Control Register
Freescale Semiconductor, Inc...
The IRQ status and control register (INTSCR) controls and monitors operation of
the IRQ module. The INTSCR:
•
Shows the state of the IRQ flag
•
Clears the IRQ latch
•
Masks IRQ interrupt request
•
Controls triggering sensitivity of the IRQ interrupt pin
Address:
$001D
Bit 7
6
5
4
Read:
3
2
IRQF
0
Write:
Reset:
ACK
0
0
0
0
0
0
1
Bit 0
IMASK
MODE
0
0
= Unimplemented
Figure 12-3. IRQ Status and Control Register (INTSCR)
IRQF — IRQ Flag Bit
This read-only status bit is high when the IRQ interrupt is pending.
1 = IRQ interrupt pending
0 = IRQ interrupt not pending
ACK — IRQ Interrupt Request Acknowledge Bit
Writing a logic 1 to this write-only bit clears the IRQ latch. ACK always reads as
logic 0. Reset clears ACK.
IMASK — IRQ Interrupt Mask Bit
Writing a logic 1 to this read/write bit disables IRQ interrupt requests. Reset
clears IMASK.
1 = IRQ interrupt requests disabled
0 = IRQ interrupt requests enabled
MODE — IRQ Edge/Level Select Bit
This read/write bit controls the triggering sensitivity of the IRQ pin. Reset clears
MODE.
1 = IRQ interrupt requests on falling edges and low levels
0 = IRQ interrupt requests on falling edges only
Data Sheet
138
MC68HC908GZ8
External Interrupt (IRQ)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 13. Keyboard Interrupt Module (KBI)
Freescale Semiconductor, Inc...
13.1 Introduction
The keyboard interrupt module (KBI) provides eight independently maskable
external interrupts which are accessible via PTA0–PTA7. When a port pin is
enabled for keyboard interrupt function, an internal pullup device is also enabled
on the pin.
13.2 Features
Features include:
•
Eight keyboard interrupt pins with separate keyboard interrupt enable bits
and one keyboard interrupt mask
•
Hysteresis buffers
•
Programmable edge-only or edge- and level- interrupt sensitivity
•
Exit from low-power modes
•
I/O (input/output) port bit(s) software configurable with pullup device(s) if
configured as input port bit(s)
13.3 Functional Description
Writing to the KBIE7–KBIE0 bits in the keyboard interrupt enable register
independently enables or disables each port A pin as a keyboard interrupt pin.
Enabling a keyboard interrupt pin also enables its internal pullup device. A logic 0
applied to an enabled keyboard interrupt pin latches a keyboard interrupt request.
A keyboard interrupt is latched when one or more keyboard pins goes low after all
were high. The MODEK bit in the keyboard status and control register controls the
triggering mode of the keyboard interrupt.
•
If the keyboard interrupt is edge-sensitive only, a falling edge on a keyboard
pin does not latch an interrupt request if another keyboard pin is already low.
To prevent losing an interrupt request on one pin because another pin is still
low, software can disable the latter pin while it is low.
•
If the keyboard interrupt is falling edge- and low-level sensitive, an interrupt
request is present as long as any keyboard interrupt pin is low and the pin
is keyboard interrupt enabled.
MC68HC908GZ8
MOTOROLA
Data Sheet
Keyboard Interrupt Module (KBI)
For More Information On This Product,
Go to: www.freescale.com
139
Freescale Semiconductor, Inc.
Keyboard Interrupt Module (KBI)
INTERNAL BUS
VECTOR FETCH
DECODER
ACKK
RESET
KBD0
VDD
.
Freescale Semiconductor, Inc...
TO PULLUP ENABLE
KEYF
D
CLR
Q
SYNCHRONIZER
.
CK
KB0IE
.
KEYBOARD
INTERRUPT
REQUEST
IMASKK
KBD7
MODEK
TO PULLUP ENABLE
KB7IE
Figure 13-1. Keyboard Module Block Diagram
Addr.
Register Name
Keyboard Status Read:
and Control Register Write:
(INTKBSCR)
See page 143. Reset:
$001A
$001B
Keyboard Interrupt Enable Read:
Register Write:
(INTKBIER)
See page 144. Reset:
Bit 7
6
5
4
3
2
0
0
0
0
KEYF
0
ACKK
1
Bit 0
IMASKK
MODEK
0
0
0
0
0
0
0
0
KBIE7
KBIE6
KBIE5
KBIE4
KBIE3
KBIE2
KBIE1
KBIE0
0
0
0
0
0
0
0
0
= Unimplemented
Figure 13-2. I/O Register Summary
If the MODEK bit is set, the keyboard interrupt pins are both falling edge- and
low-level sensitive, and both of the following actions must occur to clear a keyboard
interrupt request:
•
Vector fetch or software clear — A vector fetch generates an interrupt
acknowledge signal to clear the interrupt request. Software may generate
the interrupt acknowledge signal by writing a logic 1 to the ACKK bit in the
keyboard status and control register (INTKBSCR). The ACKK bit is useful in
applications that poll the keyboard interrupt pins and require software to
clear the keyboard interrupt request. Writing to the ACKK bit prior to leaving
an interrupt service routine can also prevent spurious interrupts due to
Data Sheet
140
MC68HC908GZ8
Keyboard Interrupt Module (KBI)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Keyboard Interrupt Module (KBI)
Keyboard Initialization
noise. Setting ACKK does not affect subsequent transitions on the keyboard
interrupt pins. A falling edge that occurs after writing to the ACKK bit latches
another interrupt request. If the keyboard interrupt mask bit, IMASKK, is
clear, the CPU loads the program counter with the vector address at
locations $FFE0 and $FFE1.
•
Return of all enabled keyboard interrupt pins to logic 1 — As long as any
enabled keyboard interrupt pin is at logic 0, the keyboard interrupt remains
set.
Freescale Semiconductor, Inc...
The vector fetch or software clear and the return of all enabled keyboard interrupt
pins to logic 1 may occur in any order.
If the MODEK bit is clear, the keyboard interrupt pin is falling-edge-sensitive only.
With MODEK clear, a vector fetch or software clear immediately clears the
keyboard interrupt request.
Reset clears the keyboard interrupt request and the MODEK bit, clearing the
interrupt request even if a keyboard interrupt pin stays at logic 0.
The keyboard flag bit (KEYF) in the keyboard status and control register can be
used to see if a pending interrupt exists. The KEYF bit is not affected by the
keyboard interrupt mask bit (IMASKK) which makes it useful in applications where
polling is preferred.
To determine the logic level on a keyboard interrupt pin, use the data direction
register to configure the pin as an input and read the data register.
NOTE:
Setting a keyboard interrupt enable bit (KBIEx) forces the corresponding keyboard
interrupt pin to be an input, overriding the data direction register. However, the data
direction register bit must be a logic 0 for software to read the pin.
13.4 Keyboard Initialization
When a keyboard interrupt pin is enabled, it takes time for the internal pullup to
reach a logic 1. Therefore, a false interrupt can occur as soon as the pin is enabled.
To prevent a false interrupt on keyboard initialization:
1. Mask keyboard interrupts by setting the IMASKK bit in the keyboard status
and control register.
2. Enable the KBI pins by setting the appropriate KBIEx bits in the keyboard
interrupt enable register.
3. Write to the ACKK bit in the keyboard status and control register to clear any
false interrupts.
4. Clear the IMASKK bit.
An interrupt signal on an edge-triggered pin can be acknowledged immediately
after enabling the pin. An interrupt signal on an edge- and level-triggered interrupt
pin must be acknowledged after a delay that depends on the external load.
MC68HC908GZ8
MOTOROLA
Data Sheet
Keyboard Interrupt Module (KBI)
For More Information On This Product,
Go to: www.freescale.com
141
Freescale Semiconductor, Inc.
Keyboard Interrupt Module (KBI)
Another way to avoid a false interrupt:
1. Configure the keyboard pins as outputs by setting the appropriate DDRA
bits in data direction register A.
2. Write logic 1s to the appropriate port A data register bits.
3. Enable the KBI pins by setting the appropriate KBIEx bits in the keyboard
interrupt enable register.
13.5 Low-Power Modes
Freescale Semiconductor, Inc...
The WAIT and STOP instructions put the microcontroller unit (MCU) in low
power-consumption standby modes.
13.5.1 Wait Mode
The keyboard module remains active in wait mode. Clearing the IMASKK bit in the
keyboard status and control register enables keyboard interrupt requests to bring
the MCU out of wait mode.
13.5.2 Stop Mode
The keyboard module remains active in stop mode. Clearing the IMASKK bit in the
keyboard status and control register enables keyboard interrupt requests to bring
the MCU out of stop mode.
13.6 Keyboard Module During Break Interrupts
The system integration module (SIM) controls whether the keyboard interrupt latch
can be cleared during the break state. The BCFE bit in the break flag control
register (BFCR) enables software to clear status bits during the break state.
To allow software to clear the keyboard interrupt latch during a break interrupt,
write a logic 1 to the BCFE bit. If a latch is cleared during the break state, it remains
cleared when the MCU exits the break state.
To protect the latch during the break state, write a logic 0 to the BCFE bit. With
BCFE at logic 0 (its default state), writing to the keyboard acknowledge bit (ACKK)
in the keyboard status and control register during the break state has no effect. See
13.7.1 Keyboard Status and Control Register.
13.7 I/O Registers
These registers control and monitor operation of the keyboard module:
•
Keyboard status and control register (INTKBSCR)
•
Keyboard interrupt enable register (INTKBIER)
Data Sheet
142
MC68HC908GZ8
Keyboard Interrupt Module (KBI)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Keyboard Interrupt Module (KBI)
I/O Registers
13.7.1 Keyboard Status and Control Register
The keyboard status and control register:
•
Flags keyboard interrupt requests
•
Acknowledges keyboard interrupt requests
•
Masks keyboard interrupt requests
•
Controls keyboard interrupt triggering sensitivity
Address: $001A
Freescale Semiconductor, Inc...
Read:
Bit 7
6
5
4
3
0
0
0
0
KEYF
Write:
Reset:
2
0
ACKK
0
0
0
0
0
0
1
Bit 0
IMASKK
MODEK
0
0
= Unimplemented
Figure 13-3. Keyboard Status and Control Register (INTKBSCR)
Bits 7–4 — Not used
These read-only bits always read as logic 0s.
KEYF — Keyboard Flag Bit
This read-only bit is set when a keyboard interrupt is pending. Reset clears the
KEYF bit.
1 = Keyboard interrupt pending
0 = No keyboard interrupt pending
ACKK — Keyboard Acknowledge Bit
Writing a logic 1 to this write-only bit clears the keyboard interrupt request.
ACKK always reads as logic 0. Reset clears ACKK.
IMASKK — Keyboard Interrupt Mask Bit
Writing a logic 1 to this read/write bit prevents the output of the keyboard
interrupt mask from generating interrupt requests. Reset clears the IMASKK bit.
1 = Keyboard interrupt requests masked
0 = Keyboard interrupt requests not masked
MODEK — Keyboard Triggering Sensitivity Bit
This read/write bit controls the triggering sensitivity of the keyboard interrupt
pins. Reset clears MODEK.
1 = Keyboard interrupt requests on falling edges and low levels
0 = Keyboard interrupt requests on falling edges only
MC68HC908GZ8
MOTOROLA
Data Sheet
Keyboard Interrupt Module (KBI)
For More Information On This Product,
Go to: www.freescale.com
143
Freescale Semiconductor, Inc.
Keyboard Interrupt Module (KBI)
13.7.2 Keyboard Interrupt Enable Register
The keyboard interrupt enable register enables or disables each port A pin to
operate as a keyboard interrupt pin.
Address: $001B
Read:
Write:
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
KBIE7
KBIE6
KBIE5
KBIE4
KBIE3
KBIE2
KBIE1
KBIE0
0
0
0
0
0
0
0
0
Freescale Semiconductor, Inc...
Figure 13-4. Keyboard Interrupt Enable Register (INTKBIER)
KBIE7–KBIE0 — Keyboard Interrupt Enable Bits
Each of these read/write bits enables the corresponding keyboard interrupt pin
to latch interrupt requests. Reset clears the keyboard interrupt enable register.
1 = PTAx pin enabled as keyboard interrupt pin
0 = PTAx pin not enabled as keyboard interrupt pin
Data Sheet
144
MC68HC908GZ8
Keyboard Interrupt Module (KBI)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 14. Low-Voltage Inhibit (LVI)
Freescale Semiconductor, Inc...
14.1 Introduction
This section describes the low-voltage inhibit (LVI) module, which monitors the
voltage on the VDD pin and can force a reset when the VDD voltage falls below the
LVI trip falling voltage, VTRIPF.
14.2 Features
Features of the LVI module include:
•
Programmable LVI reset
•
Selectable LVI trip voltage
•
Programmable stop mode operation
14.3 Functional Description
Figure 14-1 shows the structure of the LVI module. The LVI is enabled out of reset.
The LVI module contains a bandgap reference circuit and comparator. Clearing the
LVI power disable bit, LVIPWRD, enables the LVI to monitor VDD voltage. Clearing
the LVI reset disable bit, LVIRSTD, enables the LVI module to generate a reset
when VDD falls below a voltage, VTRIPF. Setting the LVI enable in stop mode bit,
LVISTOP, enables the LVI to operate in stop mode. Setting the LVI 5-V or 3-V trip
point bit, LVI5OR3, enables the trip point voltage, VTRIPF, to be configured for 5-V
operation. Clearing the LVI5OR3 bit enables the trip point voltage, VTRIPF, to be
configured for 3-V operation. The actual trip points are shown in Section 24.
Electrical Specifications.
NOTE:
After a power-on reset (POR) the LVI’s default mode of operation is 3 V. If a 5-V
system is used, the user must set the LVI5OR3 bit to raise the trip point to 5-V
operation. Note that this must be done after every power-on reset since the default
will revert back to 3-V mode after each power-on reset. If the VDD supply is below
the 5-V mode trip voltage but above the 3-V mode trip voltage when POR is
released, the part will operate because VTRIPF defaults to 3-V mode after a POR.
So, in a 5-V system care must be taken to ensure that VDD is above the 5-V mode
trip voltage after POR is released.
If the user requires 5-V mode and sets the LVI5OR3 bit after a power-on reset while
the VDD supply is not above the VTRIPR for 5-V mode, the microcontroller unit
(MCU) will immediately go into reset. The LVI in this case will hold the part in reset
MC68HC908GZ8
MOTOROLA
Data Sheet
Low-Voltage Inhibit (LVI)
For More Information On This Product,
Go to: www.freescale.com
145
Freescale Semiconductor, Inc.
Low-Voltage Inhibit (LVI)
until either VDD goes above the rising 5-V trip point, VTRIPR, which will release reset
or VDD decreases to approximately 0 V which will re-trigger the power-on reset and
reset the trip point to 3-V operation.
Freescale Semiconductor, Inc...
LVISTOP, LVIPWRD, LVI5OR3, and LVIRSTD are in the configuration register
(CONFIG1). See Figure 8-2. Configuration Register 1 (CONFIG1) for details of
the LVI’s configuration bits. Once an LVI reset occurs, the MCU remains in reset
until VDD rises above a voltage, VTRIPR, which causes the MCU to exit reset. See
20.3.2.5 Low-Voltage Inhibit (LVI) Reset for details of the interaction between the
SIM and the LVI. The output of the comparator controls the state of the LVIOUT
flag in the LVI status register (LVISR).
An LVI reset also drives the RST pin low to provide low-voltage protection to
external peripheral devices.
VDD
STOP INSTRUCTION
LVISTOP
FROM CONFIG1
FROM CONFIG1
LVIRSTD
LVIPWRD
FROM CONFIG
LOW VDD
DETECTOR
VDD > LVITrip = 0
LVI RESET
VDD ≤ LVITrip = 1
LVIOUT
LVI5OR3
FROM CONFIG1
Figure 14-1. LVI Module Block Diagram
Addr.
Register Name
Bit 7
6
5
4
3
2
1
Bit 0
Read:
LVI Status Register (LVISR)
$FE0C
Write:
See page 147.
Reset:
LVIOUT
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
= Unimplemented
Figure 14-2. LVI I/O Register Summary
Data Sheet
146
MC68HC908GZ8
Low-Voltage Inhibit (LVI)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Low-Voltage Inhibit (LVI)
LVI Status Register
14.3.1 Polled LVI Operation
In applications that can operate at VDD levels below the VTRIPF level, software can
monitor VDD by polling the LVIOUT bit. In the configuration register, the LVIPWRD
bit must be at logic 0 to enable the LVI module, and the LVIRSTD bit must be at
logic 1 to disable LVI resets.
Freescale Semiconductor, Inc...
14.3.2 Forced Reset Operation
In applications that require VDD to remain above the VTRIPF level, enabling LVI
resets allows the LVI module to reset the MCU when VDD falls below the VTRIPF
level. In the configuration register, the LVIPWRD and LVIRSTD bits must be at
logic 0 to enable the LVI module and to enable LVI resets.
14.3.3 Voltage Hysteresis Protection
Once the LVI has triggered (by having VDD fall below VTRIPF), the LVI will maintain
a reset condition until VDD rises above the rising trip point voltage, VTRIPR. This
prevents a condition in which the MCU is continually entering and exiting reset if
VDD is approximately equal to VTRIPF. VTRIPR is greater than VTRIPF by the
hysteresis voltage, VHYS.
14.3.4 LVI Trip Selection
The LVI5OR3 bit in the configuration register selects whether the LVI is configured
for 5-V or 3-V protection.
NOTE:
The microcontroller is guaranteed to operate at a minimum supply voltage. The trip
point (VTRIPF [5 V] or VTRIPF [3 V]) may be lower than this. See Section 24.
Electrical Specifications for the actual trip point voltages.
14.4 LVI Status Register
The LVI status register (LVISR) indicates if the VDD voltage was detected below
the VTRIPF level.
Address:
Read:
$FE0C
Bit 7
6
5
4
3
2
1
Bit 0
LVIOUT
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Write:
Reset:
0
= Unimplemented
Figure 14-3. LVI Status Register (LVISR)
MC68HC908GZ8
MOTOROLA
Data Sheet
Low-Voltage Inhibit (LVI)
For More Information On This Product,
Go to: www.freescale.com
147
Freescale Semiconductor, Inc.
Low-Voltage Inhibit (LVI)
LVIOUT — LVI Output Bit
This read-only flag becomes set when the VDD voltage falls below the VTRIPF
trip voltage (see Table 14-1). Reset clears the LVIOUT bit.
Freescale Semiconductor, Inc...
Table 14-1. LVIOUT Bit Indication
VDD
LVIOUT
VDD > VTRIPR
0
VDD < VTRIPF
1
VTRIPF < VDD < VTRIPR
Previous value
14.5 LVI Interrupts
The LVI module does not generate interrupt requests.
14.6 Low-Power Modes
The STOP and WAIT instructions put the MCU in low power-consumption standby
modes.
14.6.1 Wait Mode
If enabled, the LVI module remains active in wait mode. If enabled to generate
resets, the LVI module can generate a reset and bring the MCU out of wait mode.
14.6.2 Stop Mode
If enabled in stop mode (LVISTOP set), the LVI module remains active in stop
mode. If enabled to generate resets, the LVI module can generate a reset and bring
the MCU out of stop mode.
Data Sheet
148
MC68HC908GZ8
Low-Voltage Inhibit (LVI)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 15. Monitor ROM (MON)
Freescale Semiconductor, Inc...
15.1 Introduction
This section describes the monitor ROM (MON) and the monitor mode entry
methods. The monitor ROM allows complete testing of the microcontroller unit
(MCU) through a single-wire interface with a host computer. Monitor mode entry
can be achieved without use of the higher test voltage, VTST, as long as vector
addresses $FFFE and $FFFF are blank, thus reducing the hardware requirements
for in-circuit programming.
15.2 Features
Features of the monitor ROM include:
• Normal user-mode pin functionality
• One pin dedicated to serial communication between monitor read-only
memory (ROM) and host computer
• Standard mark/space non-return-to-zero (NRZ) communication with host
computer
• Standard communication baud rate (7200 @ 8-MHz bus frequency)
• Execution of code in random-access memory (RAM) or FLASH
• FLASH memory security feature(1)
• FLASH memory programming interface
• 350 bytes monitor ROM code size ($FE20 to $FF7D)
• Monitor mode entry without high voltage, VTST, if reset vector is blank
($FFFE and $FFFF contain $FF)
• Normal monitor mode entry if high voltage is applied to IRQ
15.3 Functional Description
Figure 15-1 shows a simplified diagram of the monitor mode.
The monitor ROM receives and executes commands from a host computer.
Figure 15-2 and Figure 15-3 show example circuits used to enter monitor mode
and communicate with a host computer via a standard RS-232 interface.
1. No security feature is absolutely secure. However, Motorola’s strategy is to make reading or
copying the FLASH difficult for unauthorized users.
MC68HC908GZ8
MOTOROLA
Data Sheet
Monitor ROM (MON)
For More Information On This Product,
Go to: www.freescale.com
149
Freescale Semiconductor, Inc.
Monitor ROM (MON)
POR RESET
NO
CONDITIONS
FROM Table 15-1
PTA0 = 1,
PTA1 = 0, RESET
VECTOR BLANK?
IRQ = VTST?
YES
PTA0 = 1, PTA1 = 0,
PTB0 = 1, AND
PTB1 = 0?
NO
YES
YES
Freescale Semiconductor, Inc...
NO
FORCED
MONITOR MODE
NORMAL
USER MODE
NORMAL
MONITOR MODE
INVALID
USER MODE
HOST SENDS
8 SECURITY BYTES
IS RESET
POR?
YES
NO
YES
ARE ALL
SECURITY BYTES
CORRECT?
ENABLE FLASH
NO
DISABLE FLASH
MONITOR MODE ENTRY
DEBUGGING
AND FLASH
PROGRAMMING
(IF FLASH
IS ENABLED)
EXECUTE
MONITOR CODE
YES
DOES RESET
OCCUR?
NO
Figure 15-1. Simplified Monitor Mode Entry Flowchart
Data Sheet
150
MC68HC908GZ8
Monitor ROM (MON)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Monitor ROM (MON)
Functional Description
MC68HC908GZ8
N.C.
RST
VDD
47 pF
VDDA
OSC2
MAX232
1
1 µF
+
4
Freescale Semiconductor, Inc...
0.1 µF
1 µF
+
10 k
1 kΩ
IRQ
3
10
8
9
10 k
PTB1
9.1 V
10 k
1 µF
74HC125
3
2
PTA1
10 kΩ
74HC125
5
6
DB9
7
PTB0
VDD
+
2
PTB4
V– 6
5 C2–
10 k
1 µF
V+ 2
C2+
+
VDD
OSC1
8 MHz
GND 15
C1–
10 MΩ
27 pF
+
3
1 µF
VDD
VCC 16
C1+
VDD
PTA0
VSSA
VSS
4
1
5
Figure 15-2. Normal Monitor Mode Circuit
MC68HC908GZ8
N.C.
RST
47 pF
OSC2
MAX232
1
1 µF
+
4
GND 15
C2+
V+ 2
5 C2–
0.1 µF
1 µF
1 µF
+
N.C.
+
3
10
8
9
5
IRQ
VDD
V– 6
7
OSC1
8 MHz
PTB4
N.C.
PTB0
N.C.
PTB1
N.C.
10 k
1 µF
74HC125
5
6
DB9
2
VDDA
10 MΩ
27 pF
VCC 16
C1–
+
VDD
VDD
+
3
1 µF
C1+
VDD
74HC125
3
2
PTA1
10 kΩ
PTA0
4
VSSA
VSS
1
Figure 15-3. Forced Monitor Mode
MC68HC908GZ8
MOTOROLA
Data Sheet
Monitor ROM (MON)
For More Information On This Product,
Go to: www.freescale.com
151
Freescale Semiconductor, Inc.
Monitor ROM (MON)
Simple monitor commands can access any memory address. In monitor mode, the
MCU can execute code downloaded into RAM by a host computer while most MCU
pins retain normal operating mode functions. All communication between the host
computer and the MCU is through the PTA0 pin. A level-shifting and multiplexing
interface is required between PTA0 and the host computer. PTA0 is used in a
wired-OR configuration and requires a pullup resistor.
Freescale Semiconductor, Inc...
Table 15-1 shows the pin conditions for entering monitor mode. As specified in the
table, monitor mode may be entered after a power-on reset (POR) and will allow
communication at 7200 baud provided one of the following sets of conditions is
met:
•
If $FFFE and $FFFF does not contain $FF (programmed state):
– The external clock is 4 MHz (7200 baud)
– PTB4 = low
– IRQ = VTST
•
If $FFFE and $FFFF do not contain $FF (programmed state):
– The external clock is 8 MHz (7200 baud)
– PTB4 = high
– IRQ = VTST
•
If $FFFE and $FFFF contain $FF (erased state):
– The external clock is 8 MHz (7200 baud)
– IRQ = VDD (this can be implemented through the internal IRQ pullup) or
VSS
Enter monitor mode with pin configuration shown in Table 15-1 by pulling RST low
and then high. The rising edge of RST latches monitor mode. Once monitor mode
is latched, the values on the specified pins can change.
Once out of reset, the MCU waits for the host to send eight security bytes (see
15.4 Security). After the security bytes, the MCU sends a break signal (10
consecutive logic 0s) to the host, indicating that it is ready to receive a command.
Data Sheet
152
MC68HC908GZ8
Monitor ROM (MON)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
MOTOROLA
VDD
VDD
or
GND
VTST
[6]
RST
[4]
—
Not
$FF
$FF
(blank)
COM
[8]
X
1
1
1
X
PTA0
SSEL
[10]
X
0
0
0
X
PTA1
X
X
0
0
X
PTB1
MOD0 MOD1
[12]
[14]
X
X
1
1
X
PTB0
Mode
Selection
DIV4
[16]
X
X
1
0
X
PTB4
Divider
X
COP
—
X
—
Enabled
OFF Disabled
OFF Disabled
OFF Disabled
X
PLL
OSC1
[13]
X
8 MHz
8 MHz
4 MHz
X
External
Clock
—
X
2 MHz
2 MHz
2 MHz
X
Bus
Frequency
Communication
Speed
—
X
7200
7200
7200
X
Baud
Rate
Reset condition
Comments
MC68HC908GZ8
For More Information On This Product,
Go to: www.freescale.com
Monitor ROM (MON)
9
11
NC
NC
15
7
NC
VDD
5
NC
13
3
NC
OSC1
1
NC
16
14
12
10
8
6
4
2
PTB4
PTB1
PTB0
PTA1
PTA0
IRQ
RST
GND
1. PTA0 must have a pullup resistor to VDD in monitor mode.
2. Communication speed in the table is an example to obtain a baud rate of 7200. Baud rate using external oscillator is bus frequency / 278.
3. External clock is an 4 MHz or 8 MHz crystal on OSC1 and OSC2 or a canned oscillator on OSC1.
4. X = don’t care
5. MON08 pin refers to P&E Microcomputer Systems’ MON08-Cyclone 2 by 8-pin connector.
MON08
Function
[Pin No.]
User
Forced
Monitor
VDD VDD
or
or
GND VTST
VDD
or
VTST
VTST
X
X
VDD
or
VTST
VTST
Normal
Monitor
X
GND
X
Reset
Vector
—
RST
IRQ
Mode
Serial
Communication
Table 15-1. Monitor Mode Signal Requirements and Options
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Monitor ROM (MON)
Functional Description
Data Sheet
153
Freescale Semiconductor, Inc.
Monitor ROM (MON)
15.3.1 Normal Monitor Mode
Freescale Semiconductor, Inc...
If VTST is applied to IRQ and PTB4 is low upon monitor mode entry, the bus
frequency is a divide-by-two of the input clock. If PTB4 is high with VTST applied to
IRQ upon monitor mode entry, the bus frequency will be a divide-by-four of the
input clock. Holding the PTB4 pin low when entering monitor mode causes a
bypass of a divide-by-two stage at the oscillator only if VTST is applied to IRQ. In
this event, the CGMOUT frequency is equal to the CGMXCLK frequency, and the
OSC1 input directly generates internal bus clocks. In this case, the OSC1 signal
must have a 50% duty cycle at maximum bus frequency.
When monitor mode was entered with VTST on IRQ, the computer operating
properly (COP) is disabled as long as VTST is applied to either IRQ or RST.
This condition states that as long as VTST is maintained on the IRQ pin after
entering monitor mode, or if VTST is applied to RST after the initial reset to get into
monitor mode (when VTST was applied to IRQ), then the COP will be disabled. In
the latter situation, after VTST is applied to the RST pin, VTST can be removed from
the IRQ pin in the interest of freeing the IRQ for normal functionality in monitor
mode.
15.3.2 Forced Monitor Mode
If entering monitor mode without high voltage on IRQ, then all port B pin
requirements and conditions, including the PTB4 frequency divisor selection, are
not in effect. This is to reduce circuit requirements when performing in-circuit
programming.
NOTE:
If the reset vector is blank and monitor mode is entered, the chip will see an
additional reset cycle after the initial power-on reset (POR). Once the reset vector
has been programmed, the traditional method of applying a voltage, VTST, to IRQ
must be used to enter monitor mode.
An external oscillator of 8 MHz is required for a baud rate of 7200, as the internal
bus frequency is automatically set to the external frequency divided by four.
When the forced monitor mode is entered the COP is always disabled regardless
of the state of IRQ or RST.
15.3.3 Monitor Vectors
In monitor mode, the MCU uses different vectors for reset, SWI (software interrupt),
and break interrupt than those for user mode. The alternate vectors are in the $FE
page instead of the $FF page and allow code execution from the internal monitor
firmware instead of user code.
Table 15-2 summarizes the differences between user mode and monitor mode.
Data Sheet
154
MC68HC908GZ8
Monitor ROM (MON)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Monitor ROM (MON)
Functional Description
Table 15-2. Mode Differences
Functions
Modes
Reset
Vector High
Reset
Vector Low
Break
Vector High
Break
Vector Low
SWI
Vector High
SWI
Vector Low
User
$FFFE
$FFFF
$FFFC
$FFFD
$FFFC
$FFFD
Monitor
$FEFE
$FEFF
$FEFC
$FEFD
$FEFC
$FEFD
15.3.4 Data Format
Freescale Semiconductor, Inc...
Communication with the monitor ROM is in standard non-return-to-zero (NRZ)
mark/space data format. Transmit and receive baud rates must be identical.
START
BIT
BIT 0
BIT 1
BIT 2
BIT 3
BIT 4
BIT 5
BIT 6
BIT 7
STOP
BIT
NEXT
START
BIT
Figure 15-4. Monitor Data Format
15.3.5 Break Signal
A start bit (logic 0) followed by nine logic 0 bits is a break signal. When the monitor
receives a break signal, it drives the PTA0 pin high for the duration of
approximately two bits and then echoes back the break signal.
MISSING STOP BIT
0
1
2
3
4
5
6
APPROXIMATELY 2 BITS DELAY
BEFORE ZERO ECHO
7
0
1
2
3
4
5
6
7
Figure 15-5. Break Transaction
15.3.6 Baud Rate
The communication baud rate is controlled by the crystal frequency or external
clock and the state of the PTB4 pin (when IRQ is set to VTST) upon entry into
monitor mode. If monitor mode was entered with VDD on IRQ and the reset vector
blank, then the baud rate is independent of PTB4.
Table 15-1 also lists external frequencies required to achieve a standard baud rate
of 7200 bps. The effective baud rate is the bus frequency divided by 278. If using
a crystal as the clock source, be aware of the upper frequency limit that the internal
clock module can handle. See 24.7 5.0-Volt Control Timing or 24.8 3.3-Volt
Control Timing for this limit.
MC68HC908GZ8
MOTOROLA
Data Sheet
Monitor ROM (MON)
For More Information On This Product,
Go to: www.freescale.com
155
Freescale Semiconductor, Inc.
Monitor ROM (MON)
15.3.7 Commands
The monitor ROM firmware uses these commands:
•
READ (read memory)
•
WRITE (write memory)
•
IREAD (indexed read)
•
IWRITE (indexed write)
•
READSP (read stack pointer)
•
RUN (run user program)
Freescale Semiconductor, Inc...
The monitor ROM firmware echoes each received byte back to the PTA0 pin for
error checking. An 11-bit delay at the end of each command allows the host to send
a break character to cancel the command. A delay of two bit times occurs before
each echo and before READ, IREAD, or READSP data is returned. The data
returned by a read command appears after the echo of the last byte of the
command.
NOTE:
Wait one bit time after each echo before sending the next byte.
FROM
HOST
4
ADDRESS
HIGH
READ
READ
4
1
ADDRESS
HIGH
ADDRESS
LOW
1
4
ADDRESS
LOW
DATA
1
3, 2
4
ECHO
RETURN
Notes:
1 = Echo delay, approximately 2 bit times
2 = Data return delay, approximately 2 bit times
3 = Cancel command delay, 11 bit times
4 = Wait 1 bit time before sending next byte.
Figure 15-6. Read Transaction
FROM
HOST
3
ADDRESS
HIGH
WRITE
WRITE
1
3
ADDRESS
HIGH
1
ADDRESS
LOW
3
ADDRESS
LOW
1
DATA
DATA
3
1
2, 3
ECHO
Notes:
1 = Echo delay, approximately 2 bit times
2 = Cancel command delay, 11 bit times
3 = Wait 1 bit time before sending next byte.
Figure 15-7. Write Transaction
Data Sheet
156
MC68HC908GZ8
Monitor ROM (MON)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Monitor ROM (MON)
Functional Description
A brief description of each monitor mode command is given in Table 15-3 through
Table 15-8.
Table 15-3. READ (Read Memory) Command
Description
Read byte from memory
Operand
2-byte address in high-byte:low-byte order
Data Returned
Returns contents of specified address
Opcode
$4A
Command Sequence
Freescale Semiconductor, Inc...
SENT TO MONITOR
READ
ADDRESS
HIGH
READ
ADDRESS
HIGH
ADDRESS
LOW
ADDRESS
LOW
DATA
ECHO
RETURN
Table 15-4. WRITE (Write Memory) Command
Description
Operand
Data Returned
Opcode
Write byte to memory
2-byte address in high-byte:low-byte order; low byte followed by data byte
None
$49
Command Sequence
FROM HOST
WRITE
ADDRESS
HIGH
WRITE
ADDRESS
HIGH
ADDRESS
LOW
ADDRESS
LOW
DATA
DATA
ECHO
Table 15-5. IREAD (Indexed Read) Command
Description
Operand
Data Returned
Opcode
Read next 2 bytes in memory from last address accessed
2-byte address in high byte:low byte order
Returns contents of next two addresses
$1A
Command Sequence
FROM HOST
IREAD
IREAD
DATA
ECHO
MC68HC908GZ8
MOTOROLA
DATA
RETURN
Data Sheet
Monitor ROM (MON)
For More Information On This Product,
Go to: www.freescale.com
157
Freescale Semiconductor, Inc.
Monitor ROM (MON)
Table 15-6. IWRITE (Indexed Write) Command
Description
Write to last address accessed + 1
Operand
Single data byte
Data Returned
Opcode
None
$19
Command Sequence
FROM HOST
Freescale Semiconductor, Inc...
IWRITE
IWRITE
DATA
DATA
ECHO
A sequence of IREAD or IWRITE commands can access a block of memory
sequentially over the full 64-Kbyte memory map.
Table 15-7. READSP (Read Stack Pointer) Command
Description
Operand
Data Returned
Opcode
Reads stack pointer
None
Returns incremented stack pointer value (SP + 1) in high-byte:low-byte order
$0C
Command Sequence
FROM HOST
READSP
SP
HIGH
READSP
ECHO
SP
LOW
RETURN
Table 15-8. RUN (Run User Program) Command
Description
Executes PULH and RTI instructions
Operand
None
Data Returned
None
Opcode
$28
Command Sequence
FROM HOST
RUN
RUN
ECHO
Data Sheet
158
MC68HC908GZ8
Monitor ROM (MON)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Monitor ROM (MON)
Security
The MCU executes the SWI and PSHH instructions when it enters monitor mode.
The RUN command tells the MCU to execute the PULH and RTI instructions.
Before sending the RUN command, the host can modify the stacked CPU registers
to prepare to run the host program. The READSP command returns the
incremented stack pointer value, SP + 1. The high and low bytes of the program
counter are at addresses SP + 5 and SP + 6.
Freescale Semiconductor, Inc...
SP
HIGH BYTE OF INDEX REGISTER
SP + 1
CONDITION CODE REGISTER
SP + 2
ACCUMULATOR
SP + 3
LOW BYTE OF INDEX REGISTER
SP + 4
HIGH BYTE OF PROGRAM COUNTER
SP + 5
LOW BYTE OF PROGRAM COUNTER
SP + 6
SP + 7
Figure 15-8. Stack Pointer at Monitor Mode Entry
15.4 Security
A security feature discourages unauthorized reading of FLASH locations while in
monitor mode. The host can bypass the security feature at monitor mode entry by
sending eight security bytes that match the bytes at locations $FFF6–$FFFD.
Locations $FFF6–$FFFD contain user-defined data.
NOTE:
Do not leave locations $FFF6–$FFFD blank. For security reasons, program
locations $FFF6–$FFFD even if they are not used for vectors.
During monitor mode entry, the MCU waits after the power-on reset for the host to
send the eight security bytes on pin PTA0. If the received bytes match those at
locations $FFF6–$FFFD, the host bypasses the security feature and can read all
FLASH locations and execute code from FLASH. Security remains bypassed until
a power-on reset occurs. If the reset was not a power-on reset, security remains
bypassed and security code entry is not required. See Figure 15-9.
Upon power-on reset, if the received bytes of the security code do not match the
data at locations $FFF6–$FFFD, the host fails to bypass the security feature. The
MCU remains in monitor mode, but reading a FLASH location returns an invalid
value and trying to execute code from FLASH causes an illegal address reset. After
receiving the eight security bytes from the host, the MCU transmits a break
character, signifying that it is ready to receive a command.
NOTE:
The MCU does not transmit a break character until after the host sends the eight
security bytes.
MC68HC908GZ8
MOTOROLA
Data Sheet
Monitor ROM (MON)
For More Information On This Product,
Go to: www.freescale.com
159
Freescale Semiconductor, Inc.
Monitor ROM (MON)
VDD
4096 + 32 CGMXCLK CYCLES
COMMAND
BYTE 8
BYTE 2
BYTE 1
RST
FROM HOST
PA0
4
BYTE 8 ECHO
2
Notes:
1 = Echo delay, approximately 2 bit times
2 = Data return delay, approximately 2 bit times
4 = Wait 1 bit time before sending next byte
5 = Wait until the monitor ROM runs
1
COMMAND ECHO
1
BREAK
1
BYTE 2 ECHO
FROM MCU
4
1
BYTE 1 ECHO
Freescale Semiconductor, Inc...
5
Figure 15-9. Monitor Mode Entry Timing
To determine whether the security code entered is correct, check to see if bit 6 of
RAM address $40 is set. If it is, then the correct security code has been entered
and FLASH can be accessed.
If the security sequence fails, the device should be reset by a power-on reset and
brought up in monitor mode to attempt another entry. After failing the security
sequence, the FLASH module can also be mass erased by executing an erase
routine that was downloaded into internal RAM. The mass erase operation clears
the security code locations so that all eight security bytes become $FF (blank).
Data Sheet
160
MC68HC908GZ8
Monitor ROM (MON)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 16. MSCAN08 Controller (MSCAN08)
Freescale Semiconductor, Inc...
16.1 Introduction
The MSCAN08 is the specific implementation of the Motorola scalable controller
area network (MSCAN) concept targeted for the Motorola M68HC08
Microcontroller Family.
The module is a communication controller implementing the CAN 2.0 A/B protocol
as defined in the BOSCH specification dated September, 1991.
The CAN protocol was primarily, but not exclusively, designed to be used as a
vehicle serial data bus, meeting the specific requirements of this field: real-time
processing, reliable operation in the electromagnetic interference (EMI)
environment of a vehicle, cost-effectiveness, and required bandwidth.
MSCAN08 utilizes an advanced buffer arrangement, resulting in a predictable
real-time behavior, and simplifies the application software.
16.2 Features
Basic features of the MSCAN08 are:
•
MSCAN08 enable is software controlled by bit (MSCANEN) in configuration
register (CONFIG2)
•
Modular architecture
•
Implementation of the CAN Protocol — Version 2.0A/B
– Standard and extended data frames
– 0–8 bytes data length.
– Programmable bit rate up to 1 Mbps depending on the actual bit timing
and the clock jitter of the phase-locked loop (PLL)
•
Support for remote frames
•
Double-buffered receive storage scheme
•
Triple-buffered transmit storage scheme with internal prioritization using a
“local priority” concept
•
Flexible maskable identifier filter supports alternatively one full size
extended identifier filter or two 16-bit filters or four 8-bit filters
•
Programmable wakeup functionality with integrated low-pass filter
•
Programmable loop-back mode supports self-test operation
MC68HC908GZ8
MOTOROLA
Data Sheet
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
161
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
•
Separate signalling and interrupt capabilities for all CAN receiver and
transmitter error states (warning, error passive, bus off)
•
Programmable MSCAN08 clock source either CPU bus clock or crystal
oscillator output
•
Programmable link to timer interface module 2 channel 0 for time-stamping
and network synchronization
•
Low-power sleep mode
16.3 External Pins
Freescale Semiconductor, Inc...
The MSCAN08 uses two external pins, one input (CANRx) and one output (CANTx).
The CANTx output pin represents the logic level on the CAN: 0 is for a dominant
state, and 1 is for a recessive state.
A typical CAN system with MSCAN08 is shown in Figure 16-1.
CAN STATION 1
CAN NODE 1
CAN NODE 2
CAN NODE N
MCU
CAN CONTROLLER
(MSCAN08)
CANRx
CANTx
TRANSCEIVER
CAN_H
CAN_L
C A N BUS
Figure 16-1. The CAN System
Data Sheet
162
MC68HC908GZ8
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Message Storage
Each CAN station is connected physically to the CAN bus lines through a
transceiver chip. The transceiver is capable of driving the large current needed for
the CAN and has current protection against defected CAN or defected stations.
16.4 Message Storage
MSCAN08 facilitates a sophisticated message storage system which addresses
the requirements of a broad range of network applications.
16.4.1 Background
Freescale Semiconductor, Inc...
Modern application layer software is built under two fundamental assumptions:
1. Any CAN node is able to send out a stream of scheduled messages without
releasing the bus between two messages. Such nodes will arbitrate for the
bus right after sending the previous message and will only release the bus
in case of lost arbitration.
2. The internal message queue within any CAN node is organized as such that
the highest priority message will be sent out first if more than one message
is ready to be sent.
Above behavior cannot be achieved with a single transmit buffer. That buffer must
be reloaded right after the previous message has been sent. This loading process
lasts a definite amount of time and has to be completed within the inter-frame
sequence (IFS) to be able to send an uninterrupted stream of messages. Even if
this is feasible for limited CAN bus speeds, it requires that the CPU reacts with
short latencies to the transmit interrupt.
A double buffer scheme would de-couple the re-loading of the transmit buffers from
the actual message being sent and as such reduces the reactiveness requirements
on the CPU. Problems may arise if the sending of a message would be finished just
while the CPU re-loads the second buffer. In that case, no buffer would then be
ready for transmission and the bus would be released.
At least three transmit buffers are required to meet the first of the above
requirements under all circumstances. The MSCAN08 has three transmit buffers.
The second requirement calls for some sort of internal prioritization which the
MSCAN08 implements with the “local priority” concept described in 16.4.2 Receive
Structures.
16.4.2 Receive Structures
The received messages are stored in a 2-stage input first in first out (FIFO). The
two message buffers are mapped using a "ping pong" arrangement into a single
memory area (see Figure 16-2). While the background receive buffer (RxBG) is
exclusively associated to the MSCAN08, the foreground receive buffer (RxFG) is
addressable by the central processor unit (CPU08). This scheme simplifies the
handler software, because only one address area is applicable for the receive
process.
MC68HC908GZ8
MOTOROLA
Data Sheet
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
163
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
CPU08 I BUS
MSCAN08
Freescale Semiconductor, Inc...
RxBG
RxFG
RXF
Tx0
TXE
PRIO
TXE
Tx1
PRIO
TXE
Tx2
PRIO
Figure 16-2. User Model for Message Buffer Organization
Data Sheet
164
MC68HC908GZ8
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Message Storage
Both buffers have a size of 13 bytes to store the CAN control bits, the identifier
(standard or extended), and the data content. For details, see 16.12
Programmer’s Model of Message Storage.
Freescale Semiconductor, Inc...
The receiver full flag (RXF) in the MSCAN08 receiver flag register (CRFLG),
signals the status of the foreground receive buffer. When the buffer contains a
correctly received message with matching identifier, this flag is set. See 16.13.5
MSCAN08 Receiver Flag Register (CRFLG)
On reception, each message is checked to see if it passes the filter (for details see
16.5 Identifier Acceptance Filter) and in parallel is written into RxBG. The
MSCAN08 copies the content of RxBG into RxFG(1), sets the RXF flag, and
generates a receive interrupt to the CPU(2). The user’s receive handler has to read
the received message from RxFG and to reset the RXF flag to acknowledge the
interrupt and to release the foreground buffer. A new message which can follow
immediately after the IFS field of the CAN frame, is received into RxBG. The
overwriting of the background buffer is independent of the identifier filter function.
When the MSCAN08 module is transmitting, the MSCAN08 receives its own
messages into the background receive buffer, RxBG. It does NOT overwrite RxFG,
generate a receive interrupt or acknowledge its own messages on the CAN bus.
The exception to this rule is in loop-back mode (see 16.13.2 MSCAN08 Module
Control Register 1), where the MSCAN08 treats its own messages exactly like all
other incoming messages. The MSCAN08 receives its own transmitted messages
in the event that it loses arbitration. If arbitration is lost, the MSCAN08 must be
prepared to become the receiver.
An overrun condition occurs when both the foreground and the background receive
message buffers are filled with correctly received messages with accepted
identifiers and another message is correctly received from the bus with an
accepted identifier. The latter message will be discarded and an error interrupt with
overrun indication will be generated if enabled. The MSCAN08 is still able to
transmit messages with both receive message buffers filled, but all incoming
messages are discarded.
16.4.3 Transmit Structures
The MSCAN08 has a triple transmit buffer scheme to allow multiple messages to
be set up in advance and to achieve an optimized real-time performance. The three
buffers are arranged as shown in Figure 16-2.
All three buffers have a 13-byte data structure similar to the outline of the receive
buffers (see 16.12 Programmer’s Model of Message Storage). An additional
transmit buffer priority register (TBPR) contains an 8-bit “local priority” field (PRIO)
(see 16.12.5 Transmit Buffer Priority Registers).
1. Only if the RXF flag is not set.
2. The receive interrupt will occur only if not masked. A polling scheme can be applied on RXF also.
MC68HC908GZ8
MOTOROLA
Data Sheet
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
165
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
To transmit a message, the CPU08 has to identify an available transmit buffer
which is indicated by a set transmit buffer empty (TXE) flag in the MSCAN08
transmitter flag register (CTFLG) (see 16.13.7 MSCAN08 Transmitter Flag
Register).
Freescale Semiconductor, Inc...
The CPU08 then stores the identifier, the control bits and the data content into one
of the transmit buffers. Finally, the buffer has to be flagged ready for transmission
by clearing the TXE flag.
The MSCAN08 then will schedule the message for transmission and will signal the
successful transmission of the buffer by setting the TXE flag. A transmit interrupt is
generated(1) when TXE is set and can be used to drive the application software to
re-load the buffer.
In case more than one buffer is scheduled for transmission when the CAN bus
becomes available for arbitration, the MSCAN08 uses the local priority setting of
the three buffers for prioritization. For this purpose, every transmit buffer has an
8-bit local priority field (PRIO). The application software sets this field when the
message is set up. The local priority reflects the priority of this particular message
relative to the set of messages being emitted from this node. The lowest binary
value of the PRIO field is defined as the highest priority.
The internal scheduling process takes place whenever the MSCAN08 arbitrates for
the bus. This is also the case after the occurrence of a transmission error.
When a high priority message is scheduled by the application software, it may
become necessary to abort a lower priority message being set up in one of the
three transmit buffers. As messages that are already under transmission cannot be
aborted, the user has to request the abort by setting the corresponding abort
request flag (ABTRQ) in the transmission control register (CTCR). The MSCAN08
will then grant the request, if possible, by setting the corresponding abort request
acknowledge (ABTAK) and the TXE flag in order to release the buffer and by
generating a transmit interrupt. The transmit interrupt handler software can tell from
the setting of the ABTAK flag whether the message was actually aborted
(ABTAK = 1) or sent (ABTAK = 0).
16.5 Identifier Acceptance Filter
The identifier acceptance registers (CIDAR0–CIDAR3) define the acceptance
patterns of the standard or extended identifier (ID10–ID0 or ID28–ID0). Any of
these bits can be marked ‘don’t care’ in the identifier mask registers
(CIDMR0–CIDMR3).
A filter hit is indicated to the application on software by a set RXF (receive buffer
full flag, see 16.13.5 MSCAN08 Receiver Flag Register (CRFLG)) and two bits in
the identifier acceptance control register (see 16.13.9 MSCAN08 Identifier
1. The transmit interrupt will occur only if not masked. A polling scheme can be applied on TXE also.
Data Sheet
166
MC68HC908GZ8
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Identifier Acceptance Filter
Acceptance Control Register). These identifier hit flags (IDHIT1 and IDHIT0)
clearly identify the filter section that caused the acceptance. They simplify the
application software’s task to identify the cause of the receiver interrupt. In case
that more than one hit occurs (two or more filters match) the lower hit has priority.
Freescale Semiconductor, Inc...
A very flexible programmable generic identifier acceptance filter has been
introduced to reduce the CPU interrupt loading. The filter is programmable to
operate in four different modes:
1. Single identifier acceptance filter, each to be applied to a) the full 29 bits of
the extended identifier and to the following bits of the CAN frame: RTR, IDE,
SRR or b) the 11 bits of the standard identifier plus the RTR and IDE bits of
CAN 2.0A/B messages. This mode implements a single filter for a full length
CAN 2.0B compliant extended identifier. Figure 16-3 shows how the 32-bit
filter bank (CIDAR0-3, CIDMR0-3) produces a filter 0 hit.
2. Two identifier acceptance filters, each to be applied to:
a. The 14 most significant bits of the extended identifier plus the SRR and
the IDE bits of CAN2.0B messages, or
b. The 11 bits of the identifier plus the RTR and IDE bits of CAN 2.0A/B
messages.
Figure 16-4 shows how the 32-bit filter bank (CIDAR0–CIDAR3 and
CIDMR0–CIDMR3) produces filter 0 and 1 hits.
3. Four identifier acceptance filters, each to be applied to the first eight bits of
the identifier. This mode implements four independent filters for the first
eight bits of a CAN 2.0A/B compliant standard identifier. Figure 16-5 shows
how the 32-bit filter bank (CIDAR0–CIDAR3 and CIDMR0–CIDMR3)
produces filter 0 to 3 hits.
4. Closed filter. No CAN message will be copied into the foreground buffer
RxFG, and the RXF flag will never be set.
MC68HC908GZ8
MOTOROLA
Data Sheet
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
167
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
ID28
IDR0
ID21 ID20
IDR1
ID10
IDR0
ID3 ID2
IDR1
ID15 ID14
AM7
CIDMR0
AM0 AM7
CIDMR1
AM0 AM7
CIDMR2
AC7
CIDAR0
AC0 AC7
CIDAR1
AC0 AC7
CIDAR2
IDE
ID10
IDR2
ID7 ID6
IDR3
RTR
IDR2
ID3 ID10
IDR3
ID3
AM0 AM7
CIDMR3
AM0
AC0 AC7
CIDAR3
AC0
ID Accepted (Filter 0 Hit)
Freescale Semiconductor, Inc...
Figure 16-3. Single 32-Bit Maskable Identifier Acceptance Filter
ID28
IDR0
ID21 ID20
IDR1
ID15 ID14
ID10
IDR0
ID3 ID2
IDR1
AM7
CIDMR0
AM0 AM7
CIDMR1
AM0
AC7
CIDAR0
AC0 AC7
CIDAR1
AC0
IDE
ID10
IDR2
ID7 ID6
IDR3
RTR
IDR2
ID3 ID10
IDR3
ID3
ID ACCEPTED (FILTER 0 HIT)
AM7
CIDMR2
AM0 AM7
CIDMR3
AM0
AC7
CIDAR2
AC0 AC7
CIDAR3
AC0
ID ACCEPTED (FILTER 1 HIT)
Figure 16-4. Dual 16-Bit Maskable Acceptance Filters
Data Sheet
168
MC68HC908GZ8
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Identifier Acceptance Filter
ID28
IDR0
ID21 ID20
IDR1
ID10
IDR0
ID3 ID2
IDR1
AM7
CIDMR0
AM0
AC7
CIDAR0
AC0
ID15 ID14
IDE
ID10
IDR2
ID7 ID6
IDR3
RTR
IDR2
ID3 ID10
IDR3
ID3
Freescale Semiconductor, Inc...
ID ACCEPTED (FILTER 0 HIT)
AM7
CIDMR1
AM0
AC7
CIDAR1
AC0
ID ACCEPTED (FILTER 1 HIT)
AM7
CIDMR2
AM0
AC7
CIDAR2
AC0
ID ACCEPTED (FILTER 2 HIT)
AM7
CIDMR3
AM0
AC7
CIDAR3
AC0
ID ACCEPTED (FILTER 3 HIT)
Figure 16-5. Quadruple 8-Bit Maskable Acceptance Filters
MC68HC908GZ8
MOTOROLA
Data Sheet
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
169
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Freescale Semiconductor, Inc...
16.6 Interrupts
The MSCAN08 supports four interrupt vectors mapped onto eleven different
interrupt sources, any of which can be individually masked. For details, see 16.13.5
MSCAN08 Receiver Flag Register (CRFLG) through 16.13.8 MSCAN08
Transmitter Control Register.
1. Transmit Interrupt: At least one of the three transmit buffers is empty (not
scheduled) and can be loaded to schedule a message for transmission. The
TXE flags of the empty message buffers are set.
2. Receive Interrupt: A message has been received successfully and loaded
into the foreground receive buffer. This interrupt will be emitted immediately
after receiving the EOF symbol. The RXF flag is set.
3. Wakeup Interrupt: An activity on the CAN bus occurred during MSCAN08
internal sleep mode or power-down mode (provided SLPAK = WUPIE = 1).
4. Error Interrupt: An overrun, error, or warning condition occurred. The
receiver flag register (CRFLG) will indicate one of the following conditions:
– Overrun: An overrun condition as described in 16.4.2 Receive
Structures, has occurred.
– Receiver Warning: The receive error counter has reached the CPU
warning limit of 96.
– Transmitter Warning: The transmit error counter has reached the CPU
warning limit of 96.
– Receiver Error Passive: The receive error counter has exceeded the
error passive limit of 127 and MSCAN08 has gone to error passive state.
– Transmitter Error Passive: The transmit error counter has exceeded the
error passive limit of 127 and MSCAN08 has gone to error passive state.
– Bus Off: The transmit error counter has exceeded 255 and MSCAN08
has gone to bus off state.
16.6.1 Interrupt Acknowledge
Interrupts are directly associated with one or more status flags in either the
MSCAN08 receiver flag register (CRFLG) or the MSCAN08 transmitter flag register
(CTFLG). Interrupts are pending as long as one of the corresponding flags is set.
The flags in the above registers must be reset within the interrupt handler in order
to handshake the interrupt. The flags are reset through writing a ‘1’ to the
corresponding bit position. A flag cannot be cleared if the respective condition still
prevails.
NOTE:
Bit manipulation instructions (BSET) shall not be used to clear interrupt flags.
Data Sheet
170
MC68HC908GZ8
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Protocol Violation Protection
16.6.2 Interrupt Vectors
The MSCAN08 supports four interrupt vectors as shown in Table 16-1. The vector
addresses and the relative interrupt priority are dependent on the chip integration
and to be defined.
Freescale Semiconductor, Inc...
Table 16-1. MSCAN08 Interrupt Vector Addresses
Function
Source
Local
Mask
Wakeup
WUPIF
WUPIE
RWRNIF
RWRNIE
TWRNIF
TWRNIE
RERRIF
RERRIE
TERRIF
TERRIE
BOFFIF
BOFFIE
OVRIF
OVRIE
RXF
RXFIE
TXE0
TXEIE0
TXE1
TXEIE1
TXE2
TXEIE2
Global
Mask
Error interrupts
Receive
Transmit
I bit
16.7 Protocol Violation Protection
The MSCAN08 will protect the user from accidentally violating the CAN protocol
through programming errors. The protection logic implements the following
features:
•
The receive and transmit error counters cannot be written or otherwise
manipulated.
•
All registers which control the configuration of the MSCAN08 can not
be modified while the MSCAN08 is on-line. The SFTRES bit in the
MSCAN08 module control register (see 16.13.1 MSCAN08 Module
Control Register 0) serves as a lock to protect the following registers:
– MSCAN08 module control register 1 (CMCR1)
– MSCAN08 bus timing register 0 and 1 (CBTR0 and CBTR1)
– MSCAN08 identifier acceptance control register (CIDAC)
– MSCAN08 identifier acceptance registers (CIDAR0–3)
– MSCAN08 identifier mask registers (CIDMR0–3)
•
The CANTx pin is forced to recessive when the MSCAN08 is in any of the
low-power modes.
MC68HC908GZ8
MOTOROLA
Data Sheet
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
171
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
16.8 Low-Power Modes
Freescale Semiconductor, Inc...
In addition to normal mode, the MSCAN08 has three modes with reduced power
consumption: sleep, soft reset, and power down. In sleep and soft reset mode,
power consumption is reduced by stopping all clocks except those to access the
registers. In power-down mode, all clocks are stopped and no power is consumed.
The WAIT and STOP instructions put the MCU in low-power consumption stand-by
modes. Table 16-2 summarizes the combinations of MSCAN08 and CPU modes.
A particular combination of modes is entered for the given settings of the bits
SLPAK and SFTRES. For all modes, an MSCAN08 wakeup interrupt can occur
only if SLPAK = WUPIE = 1.
.
Table 16-2. MSCAN08 versus CPU Operating Modes
CPU Mode
MSCAN08 Mode
STOP
Power Down
WAIT or RUN
SLPAK = X(1)
SFTRES = X
Sleep
SLPAK = 1
SFTRES = 0
Soft Reset
SLPAK = 0
SFTRES = 1
Normal
SLPAK = 0
SFTRES = 0
1. ‘X’ means don’t care.
16.8.1 MSCAN08 Sleep Mode
The CPU can request the MSCAN08 to enter the low-power mode by asserting
the SLPRQ bit in the module configuration register (see
Figure 16-6). The time when the MSCAN08 enters sleep mode depends on its
activity:
NOTE:
•
If it is transmitting, it continues to transmit until there is no more message to
be transmitted, and then goes into sleep mode
•
If it is receiving, it waits for the end of this message and then goes into sleep
mode
•
If it is neither transmitting or receiving, it will immediately go into sleep mode
The application software must avoid setting up a transmission (by clearing or more
TXE flags) and immediately request sleep mode (by setting SLPRQ). It then
depends on the exact sequence of operations whether MSCAN08 starts
transmitting or goes into sleep mode directly.
Data Sheet
172
MC68HC908GZ8
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Low-Power Modes
During sleep mode, the SLPAK flag is set. The application software should use
SLPAK as a handshake indication for the request (SLPRQ) to go into sleep mode.
When in sleep mode, the MSCAN08 stops its internal clocks. However, clocks to
allow register accesses still run. If the MSCAN08 is in bus-off state, it stops
counting the 128*11 consecutive recessive bits due to the stopped clocks. The
CANTx pin stays in recessive state. If RXF = 1, the message can be read and RXF
can be cleared. Copying of RxGB into RxFG doesn’t take place while in sleep
mode. It is possible to access the transmit buffers and to clear the TXE flags. No
message abort takes place while in sleep mode.
Freescale Semiconductor, Inc...
The MSCAN08 leaves sleep mode (wakes-up) when:
•
Bus activity occurs, or
•
The MCU clears the SLPRQ bit, or
•
The MCU sets the SFTRES bit
MSCAN08 RUNNING
MCU
or MSCAN08
SLPRQ = 0
SLPAK = 0
MCU
MSCAN08 SLEEPING
SLEEP REQUEST
SLPRQ = 1
SLPAK = 1
SLPRQ = 1
SLPAK = 0
MSCAN08
Figure 16-6. Sleep Request/Acknowledge Cycle
NOTE:
The MCU cannot clear the SLPRQ bit before the MSCAN08 is in sleep mode
(SLPAK=1).
After wakeup, the MSCAN08 waits for 11 consecutive recessive bits to synchronize
to the bus. As a consequence, if the MSCAN08 is woken-up by a CAN frame, this
frame is not received. The receive message buffers (RxFG and RxBG) contain
messages if they were received before sleep mode was entered. All pending
actions are executed upon wakeup: copying of RxBG into RxFG, message aborts
and message transmissions. If the MSCAN08 is still in bus-off state after sleep
mode was left, it continues counting the 128*11 consecutive recessive bits.
MC68HC908GZ8
MOTOROLA
Data Sheet
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
173
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
16.8.2 MSCAN08 Soft Reset Mode
In soft reset mode, the MSCAN08 is stopped. Registers can still be accessed. This
mode is used to initialize the module configuration, bit timing and the CAN
message filter. See 16.13.1 MSCAN08 Module Control Register 0 for a complete
description of the soft reset mode.
When setting the SFTRES bit, the MSCAN08 immediately stops all ongoing
transmissions and receptions, potentially causing CAN protocol violations.
Freescale Semiconductor, Inc...
NOTE:
The user is responsible to take care that the MSCAN08 is not active when soft reset
mode is entered. The recommended procedure is to bring the MSCAN08 into sleep
mode before the SFTRES bit is set.
16.8.3 MSCAN08 Power-Down Mode
The MSCAN08 is in power-down mode when the CPU is in stop mode.
When entering the power-down mode, the MSCAN08 immediately stops all
ongoing transmissions and receptions, potentially causing CAN protocol violations.
NOTE:
The user is responsible to take care that the MSCAN08 is not active when
power-down mode is entered. The recommended procedure is to bring the
MSCAN08 into sleep mode before the STOP instruction is executed.
To protect the CAN bus system from fatal consequences resulting from violations
of the above rule, the MSCAN08 drives the CANTx pin into recessive state.
In power-down mode, no registers can be accessed.
MSCAN08 bus activity can wake the MCU from CPU stop/MSCAN08 power-down
mode. However, until the oscillator starts up and synchronization is achieved the
MSCAN08 will not respond to incoming data.
16.8.4 CPU Wait Mode
The MSCAN08 module remains active during CPU wait mode. The MSCAN08 will
stay synchronized to the CAN bus and generates transmit, receive, and error
interrupts to the CPU, if enabled. Any such interrupt will bring the MCU out of wait
mode.
16.8.5 Programmable Wakeup Function
The MSCAN08 can be programmed to apply a low-pass filter function to the CANRx
input line while in internal sleep mode (see information on control bit WUPM in
16.13.2 MSCAN08 Module Control Register 1). This feature can be used to
protect the MSCAN08 from wakeup due to short glitches on the CAN bus lines.
Such glitches can result from electromagnetic inference within noisy environments.
Data Sheet
174
MC68HC908GZ8
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Timer Link
16.9 Timer Link
The MSCAN08 will generate a timer signal whenever a valid frame has been
received. Because the CAN specification defines a frame to be valid if no errors
occurred before the EOF field has been transmitted successfully, the timer signal
will be generated right after the EOF. A pulse of one bit time is generated. As the
MSCAN08 receiver engine also receives the frames being sent by itself, a timer
signal also will be generated after a successful transmission.
Freescale Semiconductor, Inc...
The previously described timer signal can be routed into the on-chip 2-channel
timer interface module 2 (TIM2). This signal is connected to TIM2 channel 0 input
under the control of the timer link enable (TLNKEN) bit in CMCR0.
After the timer has been programmed to capture rising edge events, it can be used
under software control to generate 16-bit time stamps which can be stored with the
received message.
16.10 Clock System
Figure 16-7 shows the structure of the MSCAN08 clock generation circuitry and its
interaction with the clock generation module (CGM). With this flexible clocking
scheme the MSCAN08 is able to handle CAN bus rates ranging from 10 kbps up
to 1 Mbps.
CGMXCLK
÷2
OSC
CGMOUT
(TO SIM)
BCS
PLL
÷2
CGM
MSCAN08
(2 * BUS FREQUENCY)
÷2
MSCANCLK
PRESCALER
CLKSRC
(1 ... 64)
Figure 16-7. Clocking Scheme
MC68HC908GZ8
MOTOROLA
Data Sheet
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
175
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
The clock source bit (CLKSRC) in the MSCAN08 module control register (CMCR1)
(see 16.13.1 MSCAN08 Module Control Register 0) defines whether the
MSCAN08 is connected to the output of the crystal oscillator or to the PLL output.
The clock source has to be chosen such that the tight oscillator tolerance
requirements (up to 0.4%) of the CAN protocol are met.
NOTE:
If the system clock is generated from a PLL, it is recommended to select the crystal
clock source rather than the system clock source due to jitter considerations,
especially at faster CAN bus rates.
Freescale Semiconductor, Inc...
A programmable prescaler is used to generate out of the MSCAN08 clock the time
quanta (Tq) clock. A time quantum is the atomic unit of time handled by the
MSCAN08.
fTq =
fMSCANCLK
Presc value
A bit time is subdivided into three segments(1) (see Figure 16-8):
•
SYNC_SEG: This segment has a fixed length of one time quantum. Signal
edges are expected to happen within this section.
•
Time segment 1: This segment includes the PROP_SEG and the
PHASE_SEG1 of the CAN standard. It can be programmed by setting the
parameter TSEG1 to consist of 4 to 16 time quanta.
•
Time segment 2: This segment represents PHASE_SEG2 of the CAN
standard. It can be programmed by setting the TSEG2 parameter to be 2 to
8 time quanta long.
fTq
Bit rate =
No. of time quanta
The synchronization jump width (SJW) can be programmed in a range of 1 to 4 time
quanta by setting the SJW parameter.
The above parameters can be set by programming the bus timing registers,
CBTR0 and CBTR1. See 16.13.3 MSCAN08 Bus Timing Register 0 and 16.13.4
MSCAN08 Bus Timing Register 1.
NOTE:
It is the user’s responsibility to make sure that the bit timing settings are in
compliance with the CAN standard,
Table 16-8 gives an overview on the CAN conforming segment settings and the
related parameter values.
1. For further explanation of the underlying concepts please refer to ISO/DIS 11 519-1,
Section 10.3.
Data Sheet
176
MC68HC908GZ8
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Clock System
Freescale Semiconductor, Inc...
NRZ SIGNAL
SYNC
_SEG
TIME SEGMENT 1
(PROP_SEG + PHASE_SEG1)
TIME SEG. 2
(PHASE_SEG2)
1
4 ... 16
2 ... 8
8... 25 TIME QUANTA
= 1 BIT TIME
SAMPLE POINT
(SINGLE OR TRIPLE SAMPLING)
Figure 16-8. Segments Within the Bit Time
Table 16-3. Time Segment Syntax
SYNC_SEG
System expects transitions to occur on the bus during this
period.
Transmit point
A node in transmit mode will transfer a new value to the CAN
bus at this point.
Sample point
A node in receive mode will sample the bus at this point. If the
three samples per bit option is selected then this point marks
the position of the third sample.
Table 16-4. CAN Standard Compliant
Bit Time Segment Settings
Time
Segment 1
TSEG1
Time
Segment 2
TSEG2
Synchronized
Jump Width
SJW
5 .. 10
4 .. 9
2
1
1 .. 2
0 .. 1
4 .. 11
3 .. 10
3
2
1 .. 3
0 .. 2
5 .. 12
4 .. 11
4
3
1 .. 4
0 .. 3
6 .. 13
5 .. 12
5
4
1 .. 4
0 .. 3
7 .. 14
6 .. 13
6
5
1 .. 4
0 .. 3
8 .. 15
7 .. 14
7
6
1 .. 4
0 .. 3
9 .. 16
8 .. 15
8
7
1 .. 4
0 .. 3
MC68HC908GZ8
MOTOROLA
Data Sheet
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
177
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
16.11 Memory Map
The MSCAN08 occupies 128 bytes in the CPU08 memory space. The absolute
mapping is implementation dependent with the base address being a multiple
of 128.
$0500
$0508
$0509
$050D
Freescale Semiconductor, Inc...
$050E
$050F
$0510
$0517
$0518
$053F
CONTROL REGISTERS
9 BYTES
RESERVED
5 BYTES
ERROR COUNTERS
2 BYTES
IDENTIFIER FILTER
8 BYTES
RESERVED
40 BYTES
$0540
RECEIVE BUFFER
$054F
$0550
TRANSMIT BUFFER 0
$055F
$0560
TRANSMIT BUFFER 1
$056F
$0570
TRANSMIT BUFFER 2
$057F
Figure 16-9. MSCAN08 Memory Map
Data Sheet
178
MC68HC908GZ8
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Programmer’s Model of Message Storage
16.12 Programmer’s Model of Message Storage
Freescale Semiconductor, Inc...
This section details the organization of the receive and transmit message buffers
and the associated control registers. For reasons of programmer interface
simplification, the receive and transmit message buffers have the same outline.
Each message buffer allocates 16 bytes in the memory map containing a 13-byte
data structure. An additional transmit buffer priority register (TBPR) is defined for
the transmit buffers.
Addr(1)
Register Name
$05b0
IDENTIFIER REGISTER 0
$05b1
IDENTIFIER REGISTER 1
$05b2
IDENTIFIER REGISTER 2
$05b3
IDENTIFIER REGISTER 3
$05b4
DATA SEGMENT REGISTER 0
$05b5
DATA SEGMENT REGISTER 1
$05b6
DATA SEGMENT REGISTER 2
$05b7
DATA SEGMENT REGISTER 3
$05b8
DATA SEGMENT REGISTER 4
$05b9
DATA SEGMENT REGISTER 5
$05bA
DATA SEGMENT REGISTER 6
$05bB
DATA SEGMENT REGISTER 7
$05bC
DATA LENGTH REGISTER
$05bD
TRANSMIT BUFFER PRIORITY REGISTER(2)
$05bE
UNUSED
$05bF
UNUSED
1. Where b equals the following:
b=4 for receive buffer
b=5 for transmit buffer 0
b=6 for transmit buffer 1
b=7 for transmit buffer 2
2. Not applicable for receive buffers
Figure 16-10. Message Buffer Organization
MC68HC908GZ8
MOTOROLA
Data Sheet
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
179
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
16.12.1 Message Buffer Outline
Figure 16-11 shows the common 13-byte data structure of receive and transmit
buffers for extended identifiers. The mapping of standard identifiers into the IDR
registers is shown in Figure 16-12. All bits of the 13-byte data structure are
undefined out of reset.
NOTE:
Freescale Semiconductor, Inc...
Addr.
The foreground receive buffer can be read anytime but cannot be written. The
transmit buffers can be read or written anytime.
Register
$05b0
IDR0
$05b1
IDR1
$05b2
IDR2
$05b3
IDR3
$05b4
DSR0
$05b5
DSR1
$05b6
DSR2
$05b7
DSR3
$05b8
DSR4
$05b9
DSR5
Read:
Write:
Read:
Write:
Read:
Write:
Read:
Write:
Read:
Write:
Read:
Write:
Read:
Write:
Read:
Write:
Read:
Write:
Read:
Write:
Bit 7
6
5
4
3
2
1
Bit 0
ID28
ID27
ID26
ID25
ID24
ID23
ID22
ID21
ID20
ID19
ID18
SRR (=1)
IDE (=1)
ID17
ID16
ID15
ID14
ID13
ID12
ID11
ID10
ID9
ID8
ID7
ID6
ID5
ID4
ID3
ID2
ID1
ID0
RTR
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
= Unimplemented
Figure 16-11. Receive/Transmit Message Buffer
Extended Identifier (IDRn)
Data Sheet
180
MC68HC908GZ8
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Programmer’s Model of Message Storage
Freescale Semiconductor, Inc...
Addr.
Register
$05bA
DSR6
$05bB
DSR7
$05bC
DLR
Read:
Write:
Read:
Write:
Bit 7
6
5
4
3
2
1
Bit 0
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
DLC3
DLC2
DLC1
DLC0
Read:
Write:
= Unimplemented
Figure 16-11. Receive/Transmit Message Buffer
Extended Identifier (IDRn) (Continued)
Addr.
Register
$05b0
IDR0
$05b1
IDR1
$05b2
IDR2
$05b3
IDR3
Read:
Write:
Read:
Write:
Bit 7
6
5
4
3
2
1
Bit 0
ID10
ID9
ID8
ID7
ID6
ID5
ID4
ID3
ID2
ID1
ID0
RTR
IDE (=0)
Read:
Write:
Read:
Write:
= Unimplemented
Figure 16-12. Standard Identifier Mapping
16.12.2 Identifier Registers
The identifiers consist of either 11 bits (ID10–ID0) for the standard, or 29 bits
(ID28–ID0) for the extended format. ID10/28 is the most significant bit and is
transmitted first on the bus during the arbitration procedure. The priority of an
identifier is defined to be highest for the smallest binary number.
SRR — Substitute Remote Request
This fixed recessive bit is used only in extended format. It must be set to 1 by
the user for transmission buffers and will be stored as received on the CAN bus
for receive buffers.
MC68HC908GZ8
MOTOROLA
Data Sheet
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
181
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Freescale Semiconductor, Inc...
IDE — ID Extended
This flag indicates whether the extended or standard identifier format is applied
in this buffer. In case of a receive buffer, the flag is set as being received and
indicates to the CPU how to process the buffer identifier registers. In case of a
transmit buffer, the flag indicates to the MSCAN08 what type of identifier to
send.
1 = Extended format, 29 bits
0 = Standard format, 11 bits
RTR — Remote Transmission Request
This flag reflects the status of the remote transmission request bit in the CAN
frame. In case of a receive buffer, it indicates the status of the received frame
and supports the transmission of an answering frame in software. In case of a
transmit buffer, this flag defines the setting of the RTR bit to be sent.
1 = Remote frame
0 = Data frame
16.12.3 Data Length Register (DLR)
This register keeps the data length field of the CAN frame.
DLC3–DLC0 — Data Length Code Bits
The data length code contains the number of bytes (data byte count) of the
respective message. At transmission of a remote frame, the data length code is
transmitted as programmed while the number of transmitted bytes is always 0.
The data byte count ranges from 0 to 8 for a data frame. Table 16-5 shows the
effect of setting the DLC bits.
Table 16-5. Data Length Codes
Data Length Code
DLC3
DLC2
DLC1
DLC0
Data Byte
Count
0
0
0
0
0
0
0
0
1
1
0
0
1
0
2
0
0
1
1
3
0
1
0
0
4
0
1
0
1
5
0
1
1
0
6
0
1
1
1
7
1
0
0
0
8
16.12.4 Data Segment Registers (DSRn)
The eight data segment registers contain the data to be transmitted or received.
The number of bytes to be transmitted or being received is determined by the data
length code in the corresponding DLR.
Data Sheet
182
MC68HC908GZ8
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Programmer’s Model of Control Registers
16.12.5 Transmit Buffer Priority Registers
Address:
$05bD
Read:
Write:
Bit 7
6
5
4
3
2
1
Bit 0
PRIO7
PRIO6
PRIO5
PRIO4
PRIO3
PRIO2
PRIO1
PRIO0
Reset:
Unaffected by reset
Freescale Semiconductor, Inc...
Figure 16-13. Transmit Buffer Priority Register (TBPR)
PRIO7–PRIO0 — Local Priority
This field defines the local priority of the associated message buffer. The local
priority is used for the internal prioritization process of the MSCAN08 and is
defined to be highest for the smallest binary number. The MSCAN08
implements the following internal prioritization mechanism:
•
All transmission buffers with a cleared TXE flag participate in the
prioritization right before the SOF is sent.
•
The transmission buffer with the lowest local priority field wins the
prioritization.
•
In case more than one buffer has the same lowest priority, the message
buffer with the lower index number wins.
16.13 Programmer’s Model of Control Registers
The programmer’s model has been laid out for maximum simplicity and efficiency.
Figure 16-14 gives an overview on the control register block of the MSCAN08.
Addr.
Register
$0500
CMCR0
$0501
CMCR1
$0502
CBTR0
$0503
CBTR1
Read:
Bit 7
6
5
4
0
0
0
SYNCH
0
0
0
0
0
SJW1
SJW0
BRP5
BRP4
SAMP
TSEG22
TSEG21
TSEG20
Write:
Read:
3
1
Bit 0
SLPRQ
SFTRES
LOOPB
WUPM
CLKSRC
BRP3
BRP2
BRP1
BRP0
TSEG13
TSEG12
TSEG11
TSEG10
R
= Reserved
TLNKEN
Write:
Read:
Write:
Read:
Write:
= Unimplemented
2
SLPAK
Figure 16-14. MSCAN08 Control Register Structure (Sheet 1 of 3)
MC68HC908GZ8
MOTOROLA
Data Sheet
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
183
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Freescale Semiconductor, Inc...
Addr.
Register
$0504
CRFLG
$0505
CRIER
$0506
CTFLG
$0507
CTCR
$0508
CIDAC
$0509
Reserved
$050E
CRXERR
$050F
CTXERR
$0510
CIDAR0
$0511
CIDAR1
$0512
CIDAR2
$0513
CIDAR3
$0514
CIDMR0
Read:
Write:
Read:
Write:
Read:
Bit 7
6
5
4
3
2
1
Bit 0
WUPIF
RWRNIF
TWRNIF
RERRIF
TERRIF
BOFFIF
OVRIF
RXF
WUPIE
RWRNIE
TWRNIE
RERRIE
TERRIE
BOFFIE
OVRIE
RXFIE
0
ABTAK2
ABTAK1
ABTAK0
0
TXE2
TXE1
TXE0
ABTRQ2
ABTRQ1
ABTRQ0
TXEIE2
TXEIE1
TXEIE0
IDAM1
IDAM0
0
0
IDHIT1
IDHIT0
Write:
Read:
0
Write:
Read:
0
0
R
R
R
R
R
R
R
R
RXERR7
RXERR6
RXERR5
RXERR4
RXERR3
RXERR2
RXERR1
RXERR0
TXERR7
TXERR6
TXERR5
TXERR4
TXERR3
TXERR2
TXERR1
TXERR0
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
R
= Reserved
Write:
Read:
Write:
Read:
Write:
Read:
Write:
Read:
Write:
Read:
Write:
Read:
Write:
Read:
Write:
Read:
Write:
0
= Unimplemented
Figure 16-14. MSCAN08 Control Register Structure (Sheet 2 of 3)
Data Sheet
184
MC68HC908GZ8
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Programmer’s Model of Control Registers
Freescale Semiconductor, Inc...
Addr.
Register
$0515
CIDMR1
$0516
CIDMR2
$0517
CIDMR3
Read:
Write:
Read:
Write:
Read:
Write:
Bit 7
6
5
4
3
2
1
Bit 0
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
R
= Reserved
1
Bit 0
SLPRQ
SFTRES
0
1
= Unimplemented
Figure 16-14. MSCAN08 Control Register Structure (Sheet 3 of 3)
16.13.1 MSCAN08 Module Control Register 0
Address: $0500
Read:
Bit 7
6
5
4
0
0
0
SYNCH
0
0
0
0
Write:
Reset:
3
TLNKEN
0
2
SLPAK
0
= Unimplemented
Figure 16-15. Module Control Register 0 (CMCR0)
SYNCH — Synchronized Status
This bit indicates whether the MSCAN08 is synchronized to the CAN bus and
as such can participate in the communication process.
1 = MSCAN08 synchronized to the CAN bus
0 = MSCAN08 not synchronized to the CAN bus
TLNKEN — Timer Enable
This flag is used to establish a link between the MSCAN08 and the on-chip timer
(see 16.9 Timer Link).
1 = The MSCAN08 timer signal output is connected to the timer input.
0 = The port is connected to the timer input.
SLPAK — Sleep Mode Acknowledge
This flag indicates whether the MSCAN08 is in module internal sleep mode. It
shall be used as a handshake for the sleep mode request (see 16.8.1
MSCAN08 Sleep Mode). If the MSCAN08 detects bus activity while in sleep
mode, it clears the flag.
1 = Sleep – MSCAN08 in internal sleep mode
0 = Wakeup – MSCAN08 is not in sleep mode
MC68HC908GZ8
MOTOROLA
Data Sheet
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
185
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Freescale Semiconductor, Inc...
SLPRQ — Sleep Request, Go to Internal Sleep Mode
This flag requests the MSCAN08 to go into an internal power-saving mode (see
16.8.1 MSCAN08 Sleep Mode).
1 = Sleep — The MSCAN08 will go into internal sleep mode.
0 = Wakeup — The MSCAN08 will function normally.
SFTRES — Soft Reset
When this bit is set by the CPU, the MSCAN08 immediately enters the soft reset
state. Any ongoing transmission or reception is aborted and synchronization to
the bus is lost.
The following registers enter and stay in their hard reset state:
CMCR0, CRFLG, CRIER, CTFLG, and CTCR.
The registers CMCR1, CBTR0, CBTR1, CIDAC, CIDAR0–CIDAR3, and
CIDMR0–CIDMR3 can only be written by the CPU when the MSCAN08 is in soft
reset state. The values of the error counters are not affected by soft reset.
When this bit is cleared by the CPU, the MSCAN08 tries to synchronize to the
CAN bus. If the MSCAN08 is not in bus-off state, it will be synchronized after 11
recessive bits on the bus; if the MSCAN08 is in bus-off state, it continues to wait
for 128 occurrences of 11 recessive bits.
Clearing SFTRES and writing to other bits in CMCR0 must be in separate
instructions.
1 = MSCAN08 in soft reset state
0 = Normal operation
16.13.2 MSCAN08 Module Control Register 1
Address:
Read:
$0501
Bit 7
6
5
4
3
0
0
0
0
0
0
0
0
0
0
Write:
Reset:
2
1
Bit 0
LOOPB
WUPM
CLKSRC
0
0
0
= Unimplemented
Figure 16-16. Module Control Register (CMCR1)
LOOPB — Loop Back Self-Test Mode
When this bit is set, the MSCAN08 performs an internal loop back which can be
used for self-test operation: the bit stream output of the transmitter is fed back
to the receiver internally. The CANRx input pin is ignored and the CANTx output
goes to the recessive state (logic 1). The MSCAN08 behaves as it does
normally when transmitting and treats its own transmitted message as a
message received from a remote node. In this state the MSCAN08 ignores the
bit sent during the ACK slot of the CAN frame Acknowledge field to insure
proper reception of its own message. Both transmit and receive interrupts are
generated.
1 = Activate loop back self-test mode
0 = Normal operation
Data Sheet
186
MC68HC908GZ8
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Programmer’s Model of Control Registers
Freescale Semiconductor, Inc...
WUPM — Wakeup Mode
This flag defines whether the integrated low-pass filter is applied to protect the
MSCAN08 from spurious wakeups (see 16.8.5 Programmable Wakeup
Function).
1 = MSCAN08 will wakeup the CPU only in cases of a dominant pulse on the
bus which has a length of at least twup.
0 = MSCAN08 will wakeup the CPU after any recessive-to-dominant edge on
the CAN bus.
CLKSRC — Clock Source
This flag defines which clock source the MSCAN08 module is driven from (see
16.10 Clock System).
1 = The MSCAN08 clock source is CGMOUT (see Figure 16-7).
0 = The MSCAN08 clock source is CGMXCLK/2 (see Figure 16-7).
NOTE:
The CMCR1 register can be written only if the SFTRES bit in the MSCAN08
module control register is set
16.13.3 MSCAN08 Bus Timing Register 0
Address:
Read:
Write:
$0502
Bit 7
6
5
4
3
2
1
Bit 0
SJW1
SJW0
BRP5
BRP4
BRP3
BRP2
BRP1
BRP0
0
0
0
0
0
0
0
0
Reset:
Figure 16-17. Bus Timing Register 0 (CBTR0)
SJW1 and SJW0 — Synchronization Jump Width
The synchronization jump width (SJW) defines the maximum number of time
quanta (Tq) clock cycles by which a bit may be shortened, or lengthened, to
achieve resynchronization on data transitions on the bus (see Table 16-6).
Table 16-6. Synchronization Jump Width
SJW1
SJW0
Synchronization Jump Width
0
0
1 Tq cycle
0
1
2 Tq cycle
1
0
3 Tq cycle
1
1
4 Tq cycle
BRP5–BRP0 — Baud Rate Prescaler
These bits determine the time quanta (Tq) clock, which is used to build up the
individual bit timing, according to Table 16-7.
MC68HC908GZ8
MOTOROLA
Data Sheet
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
187
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Freescale Semiconductor, Inc...
Table 16-7. Baud Rate Prescaler
NOTE:
BRP5
BRP4
BRP3
BRP2
BRP1
BRP0
Prescaler
Value (P)
0
0
0
0
0
0
1
0
0
0
0
0
1
2
0
0
0
0
1
0
3
0
0
0
0
1
1
4
:
:
:
:
:
:
:
:
:
:
:
:
:
:
1
1
1
1
1
1
64
The CBTR0 register can be written only if the SFTRES bit in the MSCAN08 module
control register is set.
16.13.4 MSCAN08 Bus Timing Register 1
Address:
Read:
Write:
Reset:
$0503
Bit 7
6
5
4
3
2
1
Bit 0
SAMP
TSEG22
TSEG21
TSEG20
TSEG13
TSEG12
TSEG11
TSEG10
0
0
0
0
0
0
0
0
Figure 16-18. Bus Timing Register 1 (CBTR1)
SAMP — Sampling
This bit determines the number of serial bus samples to be taken per bit time. If
set, three samples per bit are taken, the regular one (sample point) and two
preceding samples, using a majority rule. For higher bit rates, SAMP should be
cleared, which means that only one sample will be taken per bit.
1 = Three samples per bit(1)
0 = One sample per bit
TSEG22–TSEG10 — Time Segment
Time segments within the bit time fix the number of clock cycles per bit time and
the location of the sample point. Time segment 1 (TSEG1) and time segment 2
(TSEG2) are programmable as shown in Table 16-8.
The bit time is determined by the oscillator frequency, the baud rate prescaler,
and the number of time quanta (Tq) clock cycles per bit as shown in Table 16-4).
Bit time =
NOTE:
Pres value
fMSCANCLK
• number of time quanta
The CBTR1 register can only be written if the SFTRES bit in the MSCAN08 module
control register is set.
1. In this case PHASE_SEG1 must be at least 2 time quanta.
Data Sheet
188
MC68HC908GZ8
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Programmer’s Model of Control Registers
Freescale Semiconductor, Inc...
Table 16-8. Time Segment Values
TSEG13
TSEG12
TSEG11
TSEG10
Time
Segment 1
TSEG22
TSEG21
TSEG20
Time
Segment 2
0
0
0
0
1 Tq Cycle(1)
0
0
0
1 Tq Cycle(1)
0
0
0
1
2 Tq Cycles(1)
0
0
1
2 Tq Cycles
0
0
1
0
3Tq Cycles(1)
.
.
.
.
0
0
1
1
4 Tq Cycles
.
.
.
.
.
.
.
.
.
1
1
1
8Tq Cycles
.
.
.
.
.
1
16 Tq Cycles
1
1
1
1. This setting is not valid. Please refer to Table 16-4 for valid settings.
16.13.5 MSCAN08 Receiver Flag Register (CRFLG)
All bits of this register are read and clear only. A flag can be cleared by writing a 1
to the corresponding bit position. A flag can be cleared only when the condition
which caused the setting is valid no more. Writing a 0 has no effect on the flag
setting. Every flag has an associated interrupt enable flag in the CRIER register. A
hard or soft reset will clear the register.
Address:
Read:
Write:
Reset:
$0504
Bit 7
6
5
4
3
2
1
Bit 0
WUPIF
RWRNIF
TWRNIF
RERRIF
TERRIF
BOFFIF
OVRIF
RXF
0
0
0
0
0
0
0
0
Figure 16-19. Receiver Flag Register (CRFLG)
WUPIF — Wakeup Interrupt Flag
If the MSCAN08 detects bus activity while in sleep mode, it sets the WUPIF flag.
If not masked, a wakeup interrupt is pending while this flag is set.
1 = MSCAN08 has detected activity on the bus and requested wakeup.
0 = No wakeup interrupt has occurred.
RWRNIF — Receiver Warning Interrupt Flag
This flag is set when the MSCAN08 goes into warning status due to the receive
error counter (REC) exceeding 96 and neither one of the error interrupt flags or
the bus-off interrupt flag is set(1). If not masked, an error interrupt is pending
while this flag is set.
1 = MSCAN08 has gone into receiver warning status.
0 = No receiver warning status has been reached.
1. Condition to set the flag: RWRNIF = (96 ð REC) & RERRIF & TERRIF & BOFFIF
MC68HC908GZ8
MOTOROLA
Data Sheet
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
189
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
TWRNIF — Transmitter Warning Interrupt Flag
This flag is set when the MSCAN08 goes into warning status due to the transmit
error counter (TEC) exceeding 96 and neither one of the error interrupt flags or
the bus-off interrupt flag is set(1). If not masked, an error interrupt is pending
while this flag is set.
1 = MSCAN08 has gone into transmitter warning status.
0 = No transmitter warning status has been reached.
Freescale Semiconductor, Inc...
RERRIF — Receiver Error Passive Interrupt Flag
This flag is set when the MSCAN08 goes into error passive status due to the
receive error counter exceeding 127 and the bus-off interrupt flag is not set(2).
If not masked, an error interrupt is pending while this flag is set.
1 = MSCAN08 has gone into receiver error passive status.
0 = No receiver error passive status has been reached.
TERRIF — Transmitter Error Passive Interrupt Flag
This flag is set when the MSCAN08 goes into error passive status due to the
transmit error counter exceeding 127 and the bus-off interrupt flag is not set(3).
If not masked, an error interrupt is pending while this flag is set.
1 = MSCAN08 went into transmit error passive status.
0 = No transmit error passive status has been reached.
BOFFIF — Bus-Off Interrupt Flag
This flag is set when the MSCAN08 goes into bus-off status, due to the transmit
error counter exceeding 255. It cannot be cleared before the MSCAN08 has
monitored 128 times 11 consecutive ‘recessive’ bits on the bus. If not masked,
an error interrupt is pending while this flag is set.
1 = MSCAN08has gone into bus-off status.
0 = No bus-off status has been reached.
OVRIF — Overrun Interrupt Flag
This flag is set when a data overrun condition occurs. If not masked, an error
interrupt is pending while this flag is set.
1 = A data overrun has been detected since last clearing the flag.
0 = No data overrun has occurred.
RXF — Receive Buffer Full
The RXF flag is set by the MSCAN08 when a new message is available in the
foreground receive buffer. This flag indicates whether the buffer is loaded with
a correctly received message. After the CPU has read that message from the
receive buffer the RXF flag must be cleared to release the buffer. A set RXF flag
prohibits the exchange of the background receive buffer into the foreground
buffer. If not masked, a receive interrupt is pending while this flag is set.
1 = The receive buffer is full. A new message is available.
0 = The receive buffer is released (not full).
1. Condition to set the flag: TWRNIF = (96 ð TEC) & RERRIF & TERRIF & BOFFIF
2. Condition to set the flag: RERRIF = (127 ð REC ð 255) & BOFFIF
3. Condition to set the flag: TERRIF = (128 ð TEC ð 255) & BOFFIF
Data Sheet
190
MC68HC908GZ8
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Programmer’s Model of Control Registers
NOTE:
To ensure data integrity, no registers of the receive buffer shall be read while the
RXF flag is cleared.
The CRFLG register is held in the reset state when the SFTRES bit in CMCR0 is
set.
16.13.6 MSCAN08 Receiver Interrupt Enable Register
Address:
Read:
Freescale Semiconductor, Inc...
Write:
Reset:
$0505
Bit 7
6
5
4
3
2
1
Bit 0
WUPIE
RWRNIE
TWRNIE
RERRIE
TERRIE
BOFFIE
OVRIE
RXFIE
0
0
0
0
0
0
0
0
Figure 16-20. Receiver Interrupt Enable Register (CRIER)
WUPIE — Wakeup Interrupt Enable
1 = A wakeup event will result in a wakeup interrupt.
0 = No interrupt will be generated from this event.
RWRNIE — Receiver Warning Interrupt Enable
1 = A receiver warning status event will result in an error interrupt.
0 = No interrupt is generated from this event.
TWRNIE — Transmitter Warning Interrupt Enable
1 = A transmitter warning status event will result in an error interrupt.
0 = No interrupt is generated from this event.
RERRIE — Receiver Error Passive Interrupt Enable
1 = A receiver error passive status event will result in an error interrupt.
0 = No interrupt is generated from this event.
TERRIE — Transmitter Error Passive Interrupt Enable
1 = A transmitter error passive status event will result in an error interrupt.
0 = No interrupt is generated from this event.
BOFFIE — Bus-Off Interrupt Enable
1 = A bus-off event will result in an error interrupt.
0 = No interrupt is generated from this event.
OVRIE — Overrun Interrupt Enable
1 = An overrun event will result in an error interrupt.
0 = No interrupt is generated from this event.
RXFIE — Receiver Full Interrupt Enable
1 = A receive buffer full (successful message reception) event will result in a
receive interrupt.
0 = No interrupt will be generated from this event.
NOTE:
The CRIER register is held in the reset state when the SFTRES bit in CMCR0 is
set.
MC68HC908GZ8
MOTOROLA
Data Sheet
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
191
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
16.13.7 MSCAN08 Transmitter Flag Register
The abort acknowledge flags are read only. The transmitter buffer empty flags are
read and clear only. A flag can be cleared by writing a 1 to the corresponding bit
position. Writing a 0 has no effect on the flag setting. The transmitter buffer empty
flags each have an associated interrupt enable bit in the CTCR register. A hard or
soft reset will resets the register.
Address:
Read:
$0506
5
Bit 7
6
5
4
3
0
ABTAK2
ABTAK1
ABTAK0
0
0
0
0
0
0
Freescale Semiconductor, Inc...
Write:
Reset:
2
1
Bit 0
TXE2
TXE1
TXE0
1
1
1
= Unimplemented
Figure 16-21. Transmitter Flag Register (CTFLG)
ABTAK2–ABTAK0 — Abort Acknowledge
This flag acknowledges that a message has been aborted due to a pending
abort request from the CPU. After a particular message buffer has been flagged
empty, this flag can be used by the application software to identify whether the
message has been aborted successfully or has been sent. The ABTAKx flag is
cleared implicitly whenever the corresponding TXE flag is cleared.
1 = The message has been aborted.
0 = The message has not been aborted, thus has been sent out.
TXE2–TXE0 — Transmitter Empty
This flag indicates that the associated transmit message buffer is empty, thus
not scheduled for transmission. The CPU must handshake (clear) the flag after
a message has been set up in the transmit buffer and is due for transmission.
The MSCAN08 sets the flag after the message has been sent successfully. The
flag is also set by the MSCAN08 when the transmission request was
successfully aborted due to a pending abort request (see 16.12.5 Transmit
Buffer Priority Registers). If not masked, a receive interrupt is pending while
this flag is set.
Clearing a TXEx flag also clears the corresponding ABTAKx flag (ABTAK, see
above). When a TXEx flag is set, the corresponding ABTRQx bit (ABTRQ) is
cleared. See 16.13.8 MSCAN08 Transmitter Control Register
1 = The associated message buffer is empty (not scheduled).
0 = The associated message buffer is full (loaded with a message due for
transmission).
NOTE:
To ensure data integrity, no registers of the transmit buffers should be written to
while the associated TXE flag is cleared.
The CTFLG register is held in the reset state when the SFTRES bit in CMCR0 is
set.
Data Sheet
192
MC68HC908GZ8
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Programmer’s Model of Control Registers
16.13.8 MSCAN08 Transmitter Control Register
Address:
$0507
Bit 7
Read:
0
Write:
Reset:
0
6
5
4
ABTRQ2
ABTRQ1
ABTRQ0
0
0
0
3
0
0
2
1
Bit 0
TXEIE2
TXEIE1
TXEIE0
0
0
0
= Unimplemented
Figure 16-22. Transmitter Control Register (CTCR)
Freescale Semiconductor, Inc...
ABTRQ2–ABTRQ0 — Abort Request
The CPU sets an ABTRQx bit to request that an already scheduled message
buffer (TXE = 0) be aborted. The MSCAN08 will grant the request if the
message has not already started transmission, or if the transmission is not
successful (lost arbitration or error). When a message is aborted the associated
TXE and the abort acknowledge flag (ABTAK) (see 16.13.7 MSCAN08
Transmitter Flag Register) will be set and an TXE interrupt is generated if
enabled. The CPU cannot reset ABTRQx. ABTRQx is cleared implicitly
whenever the associated TXE flag is set.
1 = Abort request pending
0 = No abort request
NOTE:
The software must not clear one or more of the TXE flags in CTFLG and
simultaneously set the respective ABTRQ bit(s).
TXEIE2–TXEIE0 — Transmitter Empty Interrupt Enable
1 = A transmitter empty (transmit buffer available for transmission) event
results in a transmitter empty interrupt.
0 = No interrupt is generated from this event.
NOTE:
The CTCR register is held in the reset state when the SFTRES bit in CMCR0 is set.
MC68HC908GZ8
MOTOROLA
Data Sheet
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
193
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
16.13.9 MSCAN08 Identifier Acceptance Control Register
Address:
Read:
$0508
Bit 7
6
0
0
0
0
Write:
Reset:
5
4
IDAM1
IDAM0
0
0
3
2
1
Bit 0
0
0
IDHIT1
IDHIT0
0
0
0
0
= Unimplemented
Figure 16-23. Identifier Acceptance Control Register (CIDAC)
Freescale Semiconductor, Inc...
IDAM1–IDAM0— Identifier Acceptance Mode
The CPU sets these flags to define the identifier acceptance filter organization
(see 16.5 Identifier Acceptance Filter). Table 16-9 summarizes the different
settings. In “filter closed” mode no messages will be accepted so that the
foreground buffer will never be reloaded.
Table 16-9. Identifier Acceptance Mode Settings
IDAM1
IDAM0
Identifier Acceptance Mode
0
0
Single 32-bit acceptance filter
0
1
Two 16-bit acceptance filter
1
0
Four 8-bit acceptance filters
1
1
Filter closed
IDHIT1–IDHIT0— Identifier Acceptance Hit Indicator
The MSCAN08 sets these flags to indicate an identifier acceptance hit (see 16.5
Identifier Acceptance Filter). Table 16-9 summarizes the different settings.
Table 16-10. Identifier Acceptance Hit Indication
IDHIT1
IDHIT0
Identifier Acceptance Hit
0
0
Filter 0 hit
0
1
Filter 1 hit
1
0
Filter 2 hit
1
1
Filter 3 hit
The IDHIT indicators are always related to the message in the foreground buffer.
When a message gets copied from the background to the foreground buffer, the
indicators are updated as well.
NOTE:
The CIDAC register can be written only if the SFTRES bit in the CMCR0 is set.
Data Sheet
194
MC68HC908GZ8
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Programmer’s Model of Control Registers
16.13.10 MSCAN08 Receive Error Counter
Address:
Read:
$050E
Bit 7
6
5
4
3
2
1
Bit 0
RXERR7
RXERR6
RXERR5
RXERR4
RXERR3
RXERR2
RXERR1
RXERR0
0
0
0
0
0
0
0
0
Write:
Reset:
= Unimplemented
Freescale Semiconductor, Inc...
Figure 16-24. Receiver Error Counter (CRXERR)
This read-only register reflects the status of the MSCAN08 receive error counter.
16.13.11 MSCAN08 Transmit Error Counter
Address:
Read:
$050F
Bit 7
6
5
4
3
2
1
Bit 0
TXERR7
TXERR6
TXERR5
TXERR4
TXERR3
TXERR2
TXERR1
TXERR0
0
0
0
0
0
0
0
0
Write:
Reset:
= Unimplemented
Figure 16-25. Transmit Error Counter (CTXERR)
This read-only register reflects the status of the MSCAN08 transmit error counter.
NOTE:
Both error counters may only be read when in sleep or soft reset mode.
MC68HC908GZ8
MOTOROLA
Data Sheet
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
195
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
16.13.12 MSCAN08 Identifier Acceptance Registers
On reception each message is written into the background receive buffer. The CPU
is only signalled to read the message, however, if it passes the criteria in the
identifier acceptance and identifier mask registers (accepted); otherwise, the
message will be overwritten by the next message (dropped).
The acceptance registers of the MSCAN08 are applied on the IDR0 to IDR3
registers of incoming messages in a bit by bit manner.
Freescale Semiconductor, Inc...
For extended identifiers, all four acceptance and mask registers are applied. For
standard identifiers only the first two (CIDMR0/CIDMR1 and CIDAR0/CIDAR1) are
applied.
CIDAR0 Address: $0510
Read:
Write:
Bit 7
6
5
4
3
2
1
Bit 0
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
Reset:
Unaffected by reset
CIDAR1 Address: $050511
Read:
Write:
Bit 7
6
5
4
3
2
1
Bit 0
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
Reset:
Unaffected by reset
CIDAR2 Address: $0512
Read:
Write:
Bit 7
6
5
4
3
2
1
Bit 0
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
Reset:
Unaffected by reset
CIDAR3 Address: $0513
Read:
Write:
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
Unaffected by reset
Figure 16-26. Identifier Acceptance Registers
(CIDAR0–CIDAR3)
AC7–AC0 — Acceptance Code Bits
AC7–AC0 comprise a user-defined sequence of bits with which the
corresponding bits of the related identifier register (IDRn) of the receive
message buffer are compared. The result of this comparison is then masked
with the corresponding identifier mask register.
NOTE:
The CIDAR0–CIDAR3 registers can be written only if the SFTRES bit in CMCR0 is
set
Data Sheet
196
MC68HC908GZ8
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN08 Controller (MSCAN08)
Programmer’s Model of Control Registers
16.13.13 MSCAN08 Identifier Mask Registers (CIDMR0–CIDMR3)
The identifier mask registers specify which of the corresponding bits in the identifier
acceptance register are relevant for acceptance filtering. For standard identifiers it
is required to program the last three bits (AM2–AM0) in the mask register CIDMR1
to ‘don’t care’.
CIDMRO Address: $0514
Read:
Write:
Bit 7
6
5
4
3
2
1
Bit 0
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
Freescale Semiconductor, Inc...
Reset:
Unaffected by reset
CIDMR1 Address: $0515
Read:
Write:
Bit 7
6
5
4
3
2
1
Bit 0
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
Reset:
Unaffected by reset
CIDMR2 Address: $0516
Read:
Write:
Bit 7
6
5
4
3
2
1
Bit 0
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
Reset:
Unaffected by reset
CIDMR3 Address: $0517
Read:
Write:
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
Unaffected by reset
Figure 16-27. Identifier Mask Registers
(CIDMR0–CIDMR3)
AM7–AM0 — Acceptance Mask Bits
If a particular bit in this register is cleared, this indicates that the corresponding
bit in the identifier acceptance register must be the same as its identifier bit
before a match will be detected. The message will be accepted if all such bits
match. If a bit is set, it indicates that the state of the corresponding bit in the
identifier acceptance register will not affect whether or not the message is
accepted.
1 = Ignore corresponding acceptance code register bit.
0 = Match corresponding acceptance code register and identifier bits.
NOTE:
The CIDMR0–CIDMR3 registers can be written only if the SFTRES bit in the
CMCR0 is set
MC68HC908GZ8
MOTOROLA
Data Sheet
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
197
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
MSCAN08 Controller (MSCAN08)
Data Sheet
198
MC68HC908GZ8
MSCAN08 Controller (MSCAN08)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 17. Input/Output (I/O) Ports
Freescale Semiconductor, Inc...
17.1 Introduction
Bidirectional input-output (I/O) pins form five parallel ports. All I/O pins are
programmable as inputs or outputs. All individual bits within port A, port C, and port
D are software configurable with pullup devices if configured as input port bits. The
pullup devices are automatically and dynamically disabled when a port bit is
switched to output mode.
NOTE:
Connect any unused I/O pins to an appropriate logic level, either VDD or VSS.
Although the I/O ports do not require termination for proper operation, termination
reduces excess current consumption and the possibility of electrostatic damage.
Not all port pins are bonded out in all packages. Care sure be taken to make any
unbonded port pins an output to reduce them from being floating inputs.
Addr.
$0000
$0001
$0002
$0003
Register Name
Read:
Port A Data Register (PTA)
Write:
See page 202.
Reset:
Read:
Port B Data Register (PTB)
Write:
See page 204.
Reset:
Read:
Port C Data Register (PTC)
Write:
See page 207.
Reset:
Read:
Port D Data Register (PTD)
Write:
See page 210.
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
PTA7
PTA6
PTA5
PTA4
PTA3
PTA2
PTA1
PTA0
PTB2
PTB1
PTB0
PTC2
PTC1
PTC0
PTD2
PTD1
PTD0
Unaffected by reset
PTB7
PTB6
PTB5
PTB4
PTB3
Unaffected by reset
1
PTC6
PTC5
PTC4
PTC3
Unaffected by reset
PTD7
PTD6
PTD5
PTD4
PTD3
Unaffected by reset
= Unimplemented
Figure 17-1. I/O Port Register Summary
MC68HC908GZ8
MOTOROLA
Data Sheet
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
199
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
Addr.
Register Name
Bit 7
6
5
4
3
2
1
Bit 0
DDRA7
DDRA6
DDRA5
DDRA4
DDRA3
DDRA2
DDRA1
DDRA0
0
0
0
0
0
0
0
0
DDRB7
DDRB6
DDRB5
DDRB4
DDRB3
DDRB2
DDRB1
DDRB0
0
0
0
0
0
0
0
0
DDRC6
DDRC5
DDRC4
DDRC3
DDRC2
DDRC1
DDRC0
0
0
0
0
0
0
0
0
DDRD7
DDRD6
DDRD5
DDRD4
DDRD3
DDRD2
DDRD1
DDRD0
0
0
0
0
0
0
0
0
Read:
Port E Data Register (PTE)
Write:
See page 213.
Reset:
0
0
PTE5
PTE4
PTE3
PTE2
PTE1
PTE0
Read:
Data Direction Register E
(DDRE) Write:
See page 214.
Reset:
0
Read:
Data Direction Register A
(DDRA) Write:
See page 202.
Reset:
$0004
Read:
Data Direction Register B
(DDRB) Write:
See page 205.
Reset:
$0005
Freescale Semiconductor, Inc...
$0006
$0007
$0008
Read:
Data Direction Register C
(DDRC) Write:
See page 208.
Reset:
Read:
Data Direction Register D
(DDRD) Write:
See page 211.
Reset:
$000C
$000D
$000E
$000F
0
Unaffected by reset
0
Read:
Port A Input Pullup Enable
PTAPUE7
Register (PTAPUE) Write:
See page 204.
Reset:
0
Read:
Port C Input Pullup Enable
Register (PTCPUE) Write:
See page 209.
Reset:
0
DDRE5
DDRE4
DDRE3
DDRE2
DDRE1
DDRE0
0
0
0
0
0
0
0
PTAPUE6
PTAPUE5
PTAPUE4
PTAPUE3
PTAPUE2
PTAPUE1
PTAPUE0
0
0
0
0
0
0
0
PTCPUE6
PTCPUE5
PTCPUE4
PTCPUE3
PTCPUE2
PTCPUE1
PTCPUE0
0
0
0
0
0
0
0
PTDPUE6
PTDPUE5
PTDPUE4
PTDPUE3
PTDPUE2
PTDPUE1
PTDPUE0
0
0
0
0
0
0
0
0
0
Read:
Port D Input Pullup Enable
PTDPUE7
Register (PTDPUE) Write:
See page 213.
Reset:
0
= Unimplemented
Figure 17-1. I/O Port Register Summary (Continued)
Data Sheet
200
MC68HC908GZ8
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
Introduction
Table 17-1. Port Control Register Bits Summary
Port
Freescale Semiconductor, Inc...
A
B
C
D
E
Bit
DDR
0
DDRA0
Module Control
KBIE0
PTA0/KBD0
1
DDRA1
KBIE1
PTA1/KBD1
2
DDRA2
KBIE2
PTA2/KBD2
3
DDRA3
KBIE3
PTA3/KBD3
4
DDRA4
KBIE4
PTA4/KBD4
5
DDRA5
KBIE5
PTA5/KBD5
6
DDRA6
KBIE6
PTA6/KBD6
7
DDRA7
KBIE7
PTA7/KBD7
KBD
0
DDRB0
PTB0/AD0
1
DDRB1
PTB1/AD1
2
DDRB2
PTB2/AD2
3
DDRB3
4
DDRB4
5
DDRB5
PTB5/AD5
6
DDRB6
PTB6/AD6
7
DDRB7
PTB7/AD7
0
DDRC0
1
DDRC1
2
DDRC2
PTC2
3
DDRC3
PTC3
4
DDRC4
PTC4
5
DDRC5
PTC5
6
DDRC6
PTC6
0
DDRD0
PTD0/SS
1
DDRD1
2
DDRD2
3
DDRD3
4
DDRD4
5
DDRD5
6
DDRD6
7
DDRD7
0
DDRE0
1
DDRE1
2
DDRE2
PTE2
3
DDRE3
PTE3
4
DDRE4
PTE4
5
DDRE5
PTE5
ADC
MSCAN08
SPI
ADCH4–ADCH0
CANEN
SPE
PTB3/AD3
PTB4/AD4
PTC0
PTC1
PTD1/MISO
PTD2/MOSI
PTD3/SPSCK
TIM1
TIM2
SCI
ELS0B:ELS0A
PTD4/T1CH0
ELS1B:ELS1A
PTD5/T1CH1
ELS0B:ELS0A
PTD6/T2CH0
ELS1B:ELS1A
PTD7/T2CH1
ENSCI
MC68HC908GZ8
MOTOROLA
Pin
PTE0/TxD
PTE1/RxD
Data Sheet
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
201
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
17.2 Port A
Port A is an 8-bit special-function port that shares all eight of its pins with the
keyboard interrupt (KBI) module. Port A also has software configurable pullup
devices if configured as an input port.
17.2.1 Port A Data Register
The port A data register (PTA) contains a data latch for each of the eight port A
pins.
Freescale Semiconductor, Inc...
Address:
Read:
Write:
$0000
Bit 7
6
5
4
3
2
1
Bit 0
PTA7
PTA6
PTA5
PTA4
PTA3
PTA2
PTA1
PTA0
KBD2
KBD1
KBD0
Reset:
Alternate
Function:
Unaffected by reset
KBD7
KBD6
KBD5
KBD4
KBD3
Figure 17-2. Port A Data Register (PTA)
PTA7–PTA0 — Port A Data Bits
These read/write bits are software programmable. Data direction of each port A
pin is under the control of the corresponding bit in data direction register A.
Reset has no effect on port A data.
KBD7–KBD0 — Keyboard Inputs
The keyboard interrupt enable bits, KBIE7–KBIE0, in the keyboard interrupt
control register (KBICR) enable the port A pins as external interrupt pins. See
Section 13. Keyboard Interrupt Module (KBI).
17.2.2 Data Direction Register A
Data direction register A (DDRA) determines whether each port A pin is an input or
an output. Writing a logic 1 to a DDRA bit enables the output buffer for the
corresponding port A pin; a logic 0 disables the output buffer.
Address:
Read:
Write:
Reset:
$0004
Bit 7
6
5
4
3
2
1
Bit 0
DDRA7
DDRA6
DDRA5
DDRA4
DDRA3
DDRA2
DDRA1
DDRA0
0
0
0
0
0
0
0
0
Figure 17-3. Data Direction Register A (DDRA)
Data Sheet
202
MC68HC908GZ8
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
Port A
DDRA7–DDRA0 — Data Direction Register A Bits
These read/write bits control port A data direction. Reset clears
DDRA7–DDRA0, configuring all port A pins as inputs.
1 = Corresponding port A pin configured as output
0 = Corresponding port A pin configured as input
NOTE:
Avoid glitches on port A pins by writing to the port A data register before changing
data direction register A bits from 0 to 1.
READ DDRA ($0004)
WRITE DDRA ($0004)
INTERNAL DATA BUS
Freescale Semiconductor, Inc...
Figure 17-4 shows the port A I/O logic.
DDRAx
RESET
WRITE PTA ($0000)
PTAx
PTAx
VDD
PTAPUEx
INTERNAL
PULLUP
DEVICE
READ PTA ($0000)
Figure 17-4. Port A I/O Circuit
When bit DDRAx is a logic 1, reading address $0000 reads the PTAx data latch.
When bit DDRAx is a logic 0, reading address $0000 reads the voltage level on the
pin. The data latch can always be written, regardless of the state of its data
direction bit. Table 17-2 summarizes the operation of the port A pins.
Table 17-2. Port A Pin Functions
PTAPUE
Bit
DDRA
Bit
PTA
Bit
I/O Pin
Mode
Accesses
to DDRA
Accesses
to PTA
Read/Write
Read
Write
1
0
X(1)
Input, VDD(2)
DDRA7–DDRA0
Pin
PTA7–PTA0(3)
0
0
X
Input, Hi-Z(4)
DDRA7–DDRA0
Pin
PTA7–PTA0(3)
X
1
X
Output
DDRA7–DDRA0
PTA7–PTA0
PTA7–PTA0
1. X = Don’t care
2. I/O pin pulled up to VDD by internal pullup device
3. Writing affects data register, but does not affect input.
4. Hi-Z = High impedance
MC68HC908GZ8
MOTOROLA
Data Sheet
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
203
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
17.2.3 Port A Input Pullup Enable Register
The port A input pullup enable register (PTAPUE) contains a software configurable
pullup device for each of the eight port A pins. Each bit is individually configurable
and requires that the data direction register, DDRA, bit be configured as an input.
Each pullup is automatically and dynamically disabled when a port bit’s DDRA is
configured for output mode.
Address:
Freescale Semiconductor, Inc...
Read:
Write:
Reset:
$000D
Bit 7
6
5
4
3
2
1
Bit 0
PTAPUE7
PTAPUE6
PTAPUE5
PTAPUE4
PTAPUE3
PTAPUE2
PTAPUE1
PTAPUE0
0
0
0
0
0
0
0
0
Figure 17-5. Port A Input Pullup Enable Register (PTAPUE)
PTAPUE7–PTAPUE0 — Port A Input Pullup Enable Bits
These writable bits are software programmable to enable pullup devices on an
input port bit.
1 = Corresponding port A pin configured to have internal pullup
0 = Corresponding port A pin has internal pullup disconnected
17.3 Port B
Port B is an 8-bit special-function port that shares all eight of its pins with the
analog-to-digital converter (ADC) module.
17.3.1 Port B Data Register
The port B data register (PTB) contains a data latch for each of the eight port pins.
Address:
Read:
Write:
$0001
Bit 7
6
5
4
3
2
1
Bit 0
PTB7
PTB6
PTB5
PTB4
PTB3
PTB2
PTB1
PTB0
AD2
AD1
AD0
Reset:
Alternate
Function:
Unaffected by reset
AD7
AD6
AD5
AD4
AD3
Figure 17-6. Port B Data Register (PTB)
PTB7–PTB0 — Port B Data Bits
These read/write bits are software-programmable. Data direction of each port B
pin is under the control of the corresponding bit in data direction register B.
Reset has no effect on port B data.
Data Sheet
204
MC68HC908GZ8
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
Port B
AD7–AD0 — Analog-to-Digital Input Bits
AD7–AD0 are pins used for the input channels to the analog-to-digital converter
module. The channel select bits in the ADC status and control register define
which port B pin will be used as an ADC input and overrides any control from
the port I/O logic by forcing that pin as the input to the analog circuitry.
Freescale Semiconductor, Inc...
NOTE:
Care must be taken when reading port B while applying analog voltages to
AD7–AD0 pins. If the appropriate ADC channel is not enabled, excessive current
drain may occur if analog voltages are applied to the PTBx/ADx pin, while PTB is
read as a digital input. Those ports not selected as analog input channels are
considered digital I/O ports.
17.3.2 Data Direction Register B
Data direction register B (DDRB) determines whether each port B pin is an input or
an output. Writing a logic 1 to a DDRB bit enables the output buffer for the
corresponding port B pin; a logic 0 disables the output buffer.
Address:
Read:
Write:
Reset:
$0005
Bit 7
6
5
4
3
2
1
Bit 0
DDRB7
DDRB6
DDRB5
DDRB4
DDRB3
DDRB2
DDRB1
DDRB0
0
0
0
0
0
0
0
0
Figure 17-7. Data Direction Register B (DDRB)
DDRB7–DDRB0 — Data Direction Register B Bits
These read/write bits control port B data direction. Reset clears
DDRB7–DDRB0, configuring all port B pins as inputs.
1 = Corresponding port B pin configured as output
0 = Corresponding port B pin configured as input
NOTE:
Avoid glitches on port B pins by writing to the port B data register before changing
data direction register B bits from 0 to 1.
Figure 17-8 shows the port B I/O logic.
MC68HC908GZ8
MOTOROLA
Data Sheet
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
205
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
READ DDRB ($0005)
INTERNAL DATA BUS
WRITE DDRB ($0005)
RESET
DDRBx
WRITE PTB ($0001)
PTBx
PTBx
Freescale Semiconductor, Inc...
READ PTB ($0001)
Figure 17-8. Port B I/O Circuit
When bit DDRBx is a logic 1, reading address $0001 reads the PTBx data latch.
When bit DDRBx is a logic 0, reading address $0001 reads the voltage level on the
pin. The data latch can always be written, regardless of the state of its data
direction bit. Table 17-3 summarizes the operation of the port B pins.
Table 17-3. Port B Pin Functions
DDRB
Bit
PTB
Bit
I/O Pin
Mode
Accesses
to DDRB
Accesses
to PTB
Read/Write
Read
Write
0
X(1)
Input, Hi-Z(2)
DDRB7–DDRB0
Pin
PTB7–PTB0(3)
1
X
Output
DDRB7–DDRB0
PTB7–PTB0
PTB7–PTB0
1. X = Don’t care
2. Hi-Z = High impedance
3. Writing affects data register, but does not affect input.
Data Sheet
206
MC68HC908GZ8
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
Port C
17.4 Port C
Port C is a 7-bit, general-purpose bidirectional I/O port. Port C also has software
configurable pullup devices if configured as an input port.
17.4.1 Port C Data Register
The port C data register (PTC) contains a data latch for each of the seven port C
pins.
Freescale Semiconductor, Inc...
NOTE:
Bit 6 through bit 2 of PTC are not available in the 32-pin LQFP package.
Address:
$0002
Bit 7
Read:
Write:
1
6
5
4
3
2
1
Bit 0
PTC6
PTC5
PTC4
PTC3
PTC2
PTC1
PTC0
CANRX
CANTX
Reset:
Unaffected by reset
Alternate
Function:
= Unimplemented
Figure 17-9. Port C Data Register (PTC)
PTC6–PTC0 — Port C Data Bits
These read/write bits are software-programmable. Data direction of each port C
pin is under the control of the corresponding bit in data direction register C.
Reset has no effect on port C data.
CANRX and CANTX — MSCAN08 Bits
The CANRX–CANTX pins are the MSCAN08 modules receive and transmit pins.
The CANEN bit in the MSCAN08 control register determines, whether the
PTC1/CANRX–PTC0/CANTX pins are MSCAN08 pins or general-purpose I/O
pins. See Section 16. MSCAN08 Controller (MSCAN08).
MC68HC908GZ8
MOTOROLA
Data Sheet
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
207
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
17.4.2 Data Direction Register C
Data direction register C (DDRC) determines whether each port C pin is an input
or an output. Writing a logic 1 to a DDRC bit enables the output buffer for the
corresponding port C pin; a logic 0 disables the output buffer.
Address:
$0006
Bit 7
Read:
0
Write:
Reset:
6
5
4
3
2
1
Bit 0
DDRC6
DDRC5
DDRC4
DDRC3
DDRC2
DDRC1
DDRC0
0
0
0
0
0
0
0
0
Freescale Semiconductor, Inc...
= Unimplemented
Figure 17-10. Data Direction Register C (DDRC)
DDRC6–DDRC0 — Data Direction Register C Bits
These read/write bits control port C data direction. Reset clears
DDRC6–DDRC0, configuring all port C pins as inputs.
1 = Corresponding port C pin configured as output
0 = Corresponding port C pin configured as input
NOTE:
Avoid glitches on port C pins by writing to the port C data register before changing
data direction register C bits from 0 to 1.
Figure 17-11 shows the port C I/O logic.
READ DDRC ($0006)
INTERNAL DATA BUS
WRITE DDRC ($0006)
DDRCx
RESET
WRITE PTC ($0002)
PTCx
PTCx
VDD
PTCPUEx
READ PTC ($0002)
INTERNAL
PULLUP
DEVICE
Figure 17-11. Port C I/O Circuit
When bit DDRCx is a logic 1, reading address $0002 reads the PTCx data latch.
When bit DDRCx is a logic 0, reading address $0002 reads the voltage level on the
pin. The data latch can always be written, regardless of the state of its data
direction bit. Table 17-4 summarizes the operation of the port C pins.
Data Sheet
208
MC68HC908GZ8
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
Port C
Table 17-4. Port C Pin Functions
Freescale Semiconductor, Inc...
PTCPUE
Bit
DDRC
Bit
PTC
Bit
Accesses
to DDRC
I/O Pin
Mode
Accesses
to PTC
Read/Write
Read
Write
1
0
X(1)
Input, VDD(2)
DDRC6–DDRC0
Pin
PTC6–PTC0(3)
0
0
X
Input, Hi-Z(4)
DDRC6–DDRC0
Pin
PTC6–PTC0(3)
X
1
X
Output
DDRC6–DDRC0
PTC6–PTC0
PTC6–PTC0
1. X = Don’t care
2. I/O pin pulled up to VDD by internal pullup device.
3. Writing affects data register, but does not affect input.
4. Hi-Z = High impedance
17.4.3 Port C Input Pullup Enable Register
The port C input pullup enable register (PTCPUE) contains a software configurable
pullup device for each of the seven port C pins. Each bit is individually configurable
and requires that the data direction register, DDRC, bit be configured as an input.
Each pullup is automatically and dynamically disabled when a port bit’s DDRC is
configured for output mode.
Address:
$000E
Bit 7
Read:
0
Write:
Reset:
0
6
5
4
3
2
1
Bit 0
PTCPUE6
PTCPUE5
PTCPUE4
PTCPUE3
PTCPUE2
PTCPUE1
PTCPUE0
0
0
0
0
0
0
0
= Unimplemented
Figure 17-12. Port C Input Pullup Enable Register (PTCPUE)
PTCPUE6–PTCPUE0 — Port C Input Pullup Enable Bits
These writable bits are software programmable to enable pullup devices on an
input port bit.
1 = Corresponding port C pin configured to have internal pullup
0 = Corresponding port C pin internal pullup disconnected
MC68HC908GZ8
MOTOROLA
Data Sheet
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
209
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
17.5 Port D
Port D is an 8-bit special-function port that shares four of its pins with the serial
peripheral interface (SPI) module and four of its pins with two timer interface (TIM1
and TIM2) modules. Port D also has software configurable pullup devices if
configured as an input port.
17.5.1 Port D Data Register
Freescale Semiconductor, Inc...
The port D data register (PTD) contains a data latch for each of the eight port D
pins.
Address:
Read:
Write:
$0003
Bit 7
6
5
4
3
2
1
Bit 0
PTD7
PTD6
PTD5
PTD4
PTD3
PTD2
PTD1
PTD0
MOSI
MISO
SS
Reset:
Alternate
Function:
Unaffected by reset
T2CH1
T2CH0
T1CH1
T1CH0
SPSCK
Figure 17-13. Port D Data Register (PTD)
PTD7–PTD0 — Port D Data Bits
These read/write bits are software-programmable. Data direction of each port D
pin is under the control of the corresponding bit in data direction register D.
Reset has no effect on port D data.
T2CH1 and T2CH0 — Timer 2 Channel I/O Bits
The PTD7/T2CH1–PTD6/T2CH0 pins are the TIM2 input capture/output
compare pins. The edge/level select bits, ELSxB:ELSxA, determine whether the
PTD7/T2CH1–PTD6/T2CH0 pins are timer channel I/O pins or general-purpose
I/O pins. See Section 23. Timer Interface Module (TIM).
T1CH1 and T1CH0 — Timer 1 Channel I/O Bits
The PTD7/T1CH1–PTD6/T1CH0 pins are the TIM1 input capture/output
compare pins. The edge/level select bits, ELSxB and ELSxA, determine
whether the PTD7/T1CH1–PTD6/T1CH0 pins are timer channel I/O pins or
general-purpose I/O pins. See
Section 23. Timer Interface Module (TIM).
SPSCK — SPI Serial Clock
The PTD3/SPSCK pin is the serial clock input of the SPI module. When the SPE
bit is clear, the PTD3/SPSCK pin is available for general-purpose I/O.
MOSI — Master Out/Slave In
The PTD2/MOSI pin is the master out/slave in terminal of the SPI module. When
the SPE bit is clear, the PTD2/MOSI pin is available for general-purpose I/O.
Data Sheet
210
MC68HC908GZ8
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
Port D
Freescale Semiconductor, Inc...
MISO — Master In/Slave Out
The PTD1/MISO pin is the master in/slave out terminal of the SPI module. When
the SPI enable bit, SPE, is clear, the SPI module is disabled, and the PTD0/SS
pin is available for general-purpose I/O.
Data direction register D (DDRD) does not affect the data direction of port D pins
that are being used by the SPI module. However, the DDRD bits always
determine whether reading port D returns the states of the latches or the states
of the pins. See Table 17-5.
SS — Slave Select
The PTD0/SS pin is the slave select input of the SPI module. When the SPE bit
is clear, or when the SPI master bit, SPMSTR, is set, the PTD0/SS pin is
available for general-purpose I/O. When the SPI is enabled, the DDRB0 bit in
data direction register B (DDRB) has no effect on the PTD0/SS pin.
17.5.2 Data Direction Register D
Data direction register D (DDRD) determines whether each port D pin is an input
or an output. Writing a logic 1 to a DDRD bit enables the output buffer for the
corresponding port D pin; a logic 0 disables the output buffer.
Address:
Read:
Write:
Reset:
$0007
Bit 7
6
5
4
3
2
1
Bit 0
DDRD7
DDRD6
DDRD5
DDRD4
DDRD3
DDRD2
DDRD1
DDRD0
0
0
0
0
0
0
0
0
Figure 17-14. Data Direction Register D (DDRD)
DDRD7–DDRD0 — Data Direction Register D Bits
These read/write bits control port D data direction. Reset clears
DDRD7–DDRD0, configuring all port D pins as inputs.
1 = Corresponding port D pin configured as output
0 = Corresponding port D pin configured as input
NOTE:
Avoid glitches on port D pins by writing to the port D data register before changing
data direction register D bits from 0 to 1.
Figure 17-15 shows the port D I/O logic.
MC68HC908GZ8
MOTOROLA
Data Sheet
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
211
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
READ DDRD ($0007)
WRITE DDRD ($0007)
DDRDx
Freescale Semiconductor, Inc...
INTERNAL DATA BUS
RESET
WRITE PTD ($0003)
PTDx
PTDx
VDD
PTDPUEx
INTERNAL
PULLUP
DEVICE
READ PTD ($0003)
Figure 17-15. Port D I/O Circuit
When bit DDRDx is a logic 1, reading address $0003 reads the PTDx data latch.
When bit DDRDx is a logic 0, reading address $0003 reads the voltage level on the
pin. The data latch can always be written, regardless of the state of its data
direction bit. Table 17-5 summarizes the operation of the port D pins.
Table 17-5. Port D Pin Functions
PTDPUE
Bit
DDRD
Bit
PTD
Bit
Accesses
to DDRD
I/O Pin
Mode
Accesses
to PTD
Read/Write
Read
Write
1
0
X(1)
Input, VDD(2)
DDRD7–DDRD0
Pin
PTD7–PTD0(3)
0
0
X
Input, Hi-Z(4)
DDRD7–DDRD0
Pin
PTD7–PTD0(3)
X
1
X
Output
DDRD7–DDRD0
PTD7–PTD0
PTD7–PTD0
1. X = Don’t care
2. I/O pin pulled up to VDD by internal pullup device.
3. Writing affects data register, but does not affect input.
4. Hi-Z = High imp[edance
Data Sheet
212
MC68HC908GZ8
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
Port E
17.5.3 Port D Input Pullup Enable Register
The port D input pullup enable register (PTDPUE) contains a software configurable
pullup device for each of the eight port D pins. Each bit is individually configurable
and requires that the data direction register, DDRD, bit be configured as an input.
Each pullup is automatically and dynamically disabled when a port bit’s DDRD is
configured for output mode.
Address:
$000F
Freescale Semiconductor, Inc...
Read:
Write:
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
PTDPUE7
PTDPUE6
PTDPUE5
PTDPUE4
PTDPUE3
PTDPUE2
PTDPUE1
PTDPUE0
0
0
0
0
0
0
0
0
Figure 17-16. Port D Input Pullup Enable Register (PTDPUE)
PTDPUE7–PTDPUE0 — Port D Input Pullup Enable Bits
These writable bits are software programmable to enable pullup devices on an
input port bit.
1 = Corresponding port D pin configured to have internal pullup
0 = Corresponding port D pin has internal pullup disconnected
17.6 Port E
Port E is a 6-bit special-function port that shares two of its pins with the enhanced
serial communications interface (ESCI) module.
17.6.1 Port E Data Register
The port E data register contains a data latch for each of the six port E pins.
Address:
Read:
Write:
$0008
Bit 7
6
0
0
5
4
3
2
1
Bit 0
PTE5
PTE4
PTE3
PTE2
PTE1
PTE0
RxD
TxD
Reset:
Unaffected by reset
Alternate
Function:
= Unimplemented
Figure 17-17. Port E Data Register (PTE)
PTE5-PTE0 — Port E Data Bits
These read/write bits are software-programmable. Data direction of each port E
pin is under the control of the corresponding bit in data direction register E.
Reset has no effect on port E data.
MC68HC908GZ8
MOTOROLA
Data Sheet
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
213
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
NOTE:
Data direction register E (DDRE) does not affect the data direction of port E pins
that are being used by the ESCI module. However, the DDRE bits always
determine whether reading port E returns the states of the latches or the states of
the pins. See Table 17-6.
Freescale Semiconductor, Inc...
RxD — SCI Receive Data Input
The PTE1/RxD pin is the receive data input for the ESCI module.
When the enable SCI bit, ENSCI, is clear, the ESCI module is disabled, and the
PTE1/RxD pin is available for general-purpose I/O. See Section 19. Enhanced
Serial Communications Interface (ESCI) Module.
TxD — SCI Transmit Data Output
The PTE0/TxD pin is the transmit data output for the ESCI module. When the
enable SCI bit, ENSCI, is clear, the ESCI module is disabled, and the PTE0/TxD
pin is available for general-purpose I/O. See Section 19. Enhanced Serial
Communications Interface (ESCI) Module.
17.6.2 Data Direction Register E
Data direction register E (DDRE) determines whether each port E pin is an input or
an output. Writing a logic 1 to a DDRE bit enables the output buffer for the
corresponding port E pin; a logic 0 disables the output buffer.
Address:
Read:
$000C
Bit 7
6
0
0
0
0
Write:
Reset:
5
4
3
2
1
Bit 0
DDRE5
DDRE4
DDRE3
DDRE2
DDRE1
DDRE0
0
0
0
0
0
0
= Unimplemented
Figure 17-18. Data Direction Register E (DDRE)
DDRE5–DDRE0 — Data Direction Register E Bits
These read/write bits control port E data direction. Reset clears
DDRE5–DDRE0, configuring all port E pins as inputs.
1 = Corresponding port E pin configured as output
0 = Corresponding port E pin configured as input
NOTE:
Avoid glitches on port E pins by writing to the port E data register before changing
data direction register E bits from 0 to 1.
Figure 17-19 shows the port E I/O logic.
Data Sheet
214
MC68HC908GZ8
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Input/Output (I/O) Ports
Port E
READ DDRE ($000C)
INTERNAL DATA BUS
WRITE DDRE ($000C)
RESET
DDREx
WRITE PTE ($0008)
PTEx
PTEx
Freescale Semiconductor, Inc...
READ PTE ($0008)
Figure 17-19. Port E I/O Circuit
When bit DDREx is a logic 1, reading address $0008 reads the PTEx data latch.
When bit DDREx is a logic 0, reading address $0008 reads the voltage level on the
pin. The data latch can always be written, regardless of the state of its data
direction bit. Table 17-6 summarizes the operation of the port E pins.
Table 17-6. Port E Pin Functions
DDRE
Bit
PTE
Bit
I/O Pin
Mode
Accesses
to DDRE
Accesses
to PTE
Read/Write
Read
Write
0
X(1)
Input, Hi-Z(2)
DDRE5–DDRE0
Pin
PTE5–PTE0(3)
1
X
Output
DDRE5–DDRE0
PTE5–PTE0
PTE5–PTE0
1. X = Don’t care
2. Hi-Z = High impedance
3. Writing affects data register, but does not affect input.
MC68HC908GZ8
MOTOROLA
Data Sheet
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
215
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Input/Output (I/O) Ports
Data Sheet
216
MC68HC908GZ8
Input/Output (I/O) Ports
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 18. Random-Access Memory (RAM)
18.1 Introduction
Freescale Semiconductor, Inc...
This section describes the 1024 bytes of RAM (random-access memory).
18.2 Functional Description
Addresses $0040 through $043F are RAM locations. The location of the stack
RAM is programmable. The 16-bit stack pointer allows the stack to be anywhere in
the 64-Kbyte memory space.
NOTE:
For correct operation, the stack pointer must point only to RAM locations.
Within page zero are 192 bytes of RAM. Because the location of the stack RAM is
programmable, all page zero RAM locations can be used for I/O control and user
data or code. When the stack pointer is moved from its reset location at $00FF out
of page zero, direct addressing mode instructions can efficiently access all page
zero RAM locations. Page zero RAM, therefore, provides ideal locations for
frequently accessed global variables.
Before processing an interrupt, the CPU uses five bytes of the stack to save the
contents of the CPU registers.
NOTE:
For M6805 compatibility, the H register is not stacked.
During a subroutine call, the CPU uses two bytes of the stack to store the return
address. The stack pointer decrements during pushes and increments during pulls.
NOTE:
Be careful when using nested subroutines. The CPU may overwrite data in the
RAM during a subroutine or during the interrupt stacking operation.
MC68HC908GZ8
MOTOROLA
Data Sheet
Random-Access Memory (RAM)
For More Information On This Product,
Go to: www.freescale.com
217
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Random-Access Memory (RAM)
Data Sheet
218
MC68HC908GZ8
Random-Access Memory (RAM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 19. Enhanced Serial Communications Interface (ESCI) Module
Freescale Semiconductor, Inc...
19.1 Introduction
The enhanced serial communications interface (ESCI) module allows
asynchronous communications with peripheral devices and other microcontroller
units (MCU).
19.2 Features
Features include:
•
Full-duplex operation
•
Standard mark/space non-return-to-zero (NRZ) format
•
Programmable baud rates
•
Programmable 8-bit or 9-bit character length
•
Fine adjust baud rate prescalers for precise control of baud rate
•
Arbiter module:
– Measurement of received bit timings for baud rate recovery without use
of external timer
– Bitwise arbitration for arbitrated UART communications
•
LIN specific enhanced features:
– Generation of LIN 1.2 break symbols without extra software steps on
each message
– Break detection filtering to prevent false interrupts
•
Separately enabled transmitter and receiver
•
Separate receiver and transmitter central processor unit (CPU) interrupt
requests
•
Programmable transmitter output polarity
•
Two receiver wakeup methods:
– Idle line wakeup
– address mark wakeup
MC68HC908GZ8
MOTOROLA
Data Sheet
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
219
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Enhanced Serial Communications Interface (ESCI) Module
•
Interrupt-driven operation with eight interrupt flags:
– Transmitter empty
– Transmission complete
– Receiver full
– Idle receiver input
– Receiver overrun
– Noise error
– Framing error
– Parity error
•
Receiver framing error detection
•
Hardware parity checking
•
1/16 bit-time noise detection
19.3 Pin Name Conventions
The generic names of the ESCI input/output (I/O) pins are:
•
RxD (receive data)
•
TxD (transmit data)
ESCI I/O lines are implemented by sharing parallel I/O port pins. The full name of
an ESCI input or output reflects the name of the shared port pin. Table 19-1 shows
the full names and the generic names of the ESCI I/O pins. The generic pin names
appear in the text of this section.
Table 19-1. Pin Name Conventions
Generic Pin Names
Full Pin Names
RxD
TxD
PTE1/RxD
PTE0/TxD
19.4 Functional Description
Figure 19-1 shows the structure of the ESCI module. The ESCI allows full-duplex,
asynchronous, NRZ serial communication between the MCU and remote devices,
including other MCUs. The transmitter and receiver of the ESCI operate
independently, although they use the same baud rate generator. During normal
operation, the CPU monitors the status of the ESCI, writes the data to be
transmitted, and processes received data.
For reference, a summary of the ESCI module input/output registers is provided in
Figure 19-2.
Data Sheet
220
MC68HC908GZ8
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
Functional Description
INTERNAL BUS
ERROR
INTERRUPT
CONTROL
RECEIVE
SHIFT REGISTER
RxD
ESCI DATA
REGISTER
RECEIVER
INTERRUPT
CONTROL
TRANSMITTER
INTERRUPT
CONTROL
ESCI DATA
REGISTER
ARBITER-
TxD
SCI_TxD
TXINV
LINR
SCTIE
R8
TCIE
T8
SCRIE
ILIE
TE
SCTE
RE
TC
RWU
SBK
SCRF
OR
ORIE
IDLE
NF
NEIE
FE
FEIE
PE
PEIE
LOOPS
LOOPS
RECEIVE
CONTROL
WAKEUP
CONTROL
ENSCI
ENSCI
TRANSMIT
CONTROL
FLAG
CONTROL
BKF
M
RPF
WAKE
LINT
ILTY
PRESCALER
BUS CLOCK
Freescale Semiconductor, Inc...
TRANSMIT
SHIFT REGISTER
RxD
÷4
PRESCALER
BAUD RATE
GENERATOR
÷ 16
PEN
PTY
DATA SELECTION
CONTROL
Figure 19-1. ESCI Module Block Diagram
MC68HC908GZ8
MOTOROLA
Data Sheet
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
221
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
Addr.
Register Name
Read:
ESCI Prescaler Register
(SCPSC) Write:
See page 246.
Reset:
$0009
Read:
ESCI Arbiter Control
Register (SCIACTL) Write:
See page 250.
Reset:
$000A
Read:
ESCI Arbiter Data
Register (SCIADAT) Write:
See page 251.
Reset:
Freescale Semiconductor, Inc...
$000B
Read:
ESCI Control Register 1
(SCC1) Write:
See page 235.
Reset:
$0013
Read:
ESCI Control Register 2
(SCC2) Write:
See page 237.
Reset:
$0014
5
4
3
2
1
Bit 0
PDS2
PDS1
PDS0
PSSB4
PSSB3
PSSB2
PSSB1
PSSB0
0
0
0
0
0
0
0
0
AFIN
ARUN
AROVFL
ARD8
AM0
ACLK
ALOST
AM1
0
0
0
0
0
0
0
0
ARD7
ARD6
ARD5
ARD4
ARD3
ARD2
ARD1
ARD0
0
0
0
0
0
0
0
0
LOOPS
ENSCI
TXINV
M
WAKE
ILTY
PEN
PTY
0
0
0
0
0
0
0
0
SCTIE
TCIE
SCRIE
ILIE
TE
RE
RWU
SBK
0
0
0
0
0
0
0
0
T8
R
R
ORIE
NEIE
FEIE
PEIE
R8
U
0
0
0
0
0
0
0
Read:
ESCI Status Register 1
(SCS1) Write:
See page 241.
Reset:
SCTE
TC
SCRF
IDLE
OR
NF
FE
PE
1
1
0
0
0
0
0
0
Read:
ESCI Status Register 2
(SCS2) Write:
See page 243.
Reset:
0
0
0
0
0
0
BKF
RPF
0
0
0
0
0
0
0
0
Read:
ESCI Data Register (SCDR)
Write:
See page 244.
Reset:
R7
R6
R5
R4
R3
R2
R1
R0
T7
T6
T5
T4
T3
T2
T1
T0
$0016
$0017
$0019
6
Read:
ESCI Control Register 3
(SCC3) Write:
See page 239.
Reset:
$0015
$0018
Bit 7
Read:
ESCI Baud Rate Register
(SCBR) Write:
See page 244.
Reset:
Unaffected by reset
LINT
LINR
SCP1
SCP0
R
SCR2
SCR1
SCR0
0
0
0
0
0
0
0
0
R
= Reserved
= Unimplemented
Figure 19-2. ESCI I/O Register Summary
Data Sheet
222
MC68HC908GZ8
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
Functional Description
19.4.1 Data Format
The SCI uses the standard non-return-to-zero mark/space data format illustrated
in Figure 19-3.
Freescale Semiconductor, Inc...
START
BIT
START
BIT
8-BIT DATA FORMAT
(BIT M IN SCC1 CLEAR)
BIT 0
BIT 1
BIT 2
BIT 3
BIT 4
BIT 5
BIT 6
PARITY
OR DATA
BIT
BIT 7
PARITY
OR DATA
BIT
9-BIT DATA FORMAT
(BIT M IN SCC1 SET)
BIT 0
BIT 1
BIT 2
BIT 3
BIT 4
BIT 5
STOP
BIT
BIT 6
BIT 7
BIT 8
NEXT
START
BIT
NEXT
START
BIT
STOP
BIT
Figure 19-3. SCI Data Formats
19.4.2 Transmitter
Figure 19-4 shows the structure of the SCI transmitter and the registers are
summarized in Figure 19-2.
19.4.2.1 Character Length
The transmitter can accommodate either 8-bit or 9-bit data. The state of the M bit
in ESCI control register 1 (SCC1) determines character length. When transmitting
9-bit data, bit T8 in ESCI control register 3 (SCC3) is the ninth bit (bit 8).
19.4.2.2 Character Transmission
During an ESCI transmission, the transmit shift register shifts a character out to the
TxD pin. The ESCI data register (SCDR) is the write-only buffer between the
internal data bus and the transmit shift register.
MC68HC908GZ8
MOTOROLA
Data Sheet
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
223
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
INTERNAL BUS
BAUD
DIVIDER
÷ 16
ESCI DATA REGISTER
SCP1
11-BIT
TRANSMIT
SHIFT REGISTER
STOP
SCP0
SCR1
H
SCR2
8
7
6
5
4
3
2
START
PRESCALER
÷4
1
0
L
SCI_TxD
PSSB3
PTY
MSB
PARITY
GENERATION
T8
BREAK
(ALL ZEROS)
PSSB4
PEN
PREAMBLE
(ALL ONES)
PDS0
M
SHIFT ENABLE
PDS1
TXINV
LOAD FROM SCDR
PDS2
TRANSMITTER CPU INTERRUPT REQUEST
BUS CLOCK
PRESCALER
Freescale Semiconductor, Inc...
SCR0
TRANSMITTER
CONTROL LOGIC
PSSB2
PSSB1
PSSB0
SCTE
SCTE
SCTIE
TC
TCIE
SBK
LOOPS
SCTIE
ENSCI
TC
TE
TCIE
LINT
Figure 19-4. ESCI Transmitter
To initiate an ESCI transmission:
1. Enable the ESCI by writing a logic 1 to the enable ESCI bit (ENSCI) in ESCI
control register 1 (SCC1).
2. Enable the transmitter by writing a logic 1 to the transmitter enable bit (TE)
in ESCI control register 2 (SCC2).
3. Clear the ESCI transmitter empty bit (SCTE) by first reading ESCI status
register 1 (SCS1) and then writing to the SCDR. For 9-bit data, also write the
T8 bit in SCC3.
4. Repeat step 3 for each subsequent transmission.
At the start of a transmission, transmitter control logic automatically loads the
transmit shift register with a preamble of logic 1s. After the preamble shifts out,
control logic transfers the SCDR data into the transmit shift register. A logic 0 start
Data Sheet
224
MC68HC908GZ8
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
Functional Description
bit automatically goes into the least significant bit (LSB) position of the transmit shift
register. A logic 1 stop bit goes into the most significant bit (MSB) position.
Freescale Semiconductor, Inc...
The ESCI transmitter empty bit, SCTE, in SCS1 becomes set when the SCDR
transfers a byte to the transmit shift register. The SCTE bit indicates that the SCDR
can accept new data from the internal data bus. If the ESCI transmit interrupt
enable bit, SCTIE, in SCC2 is also set, the SCTE bit generates a transmitter CPU
interrupt request.
When the transmit shift register is not transmitting a character, the TxD pin goes to
the idle condition, logic 1. If at any time software clears the ENSCI bit in ESCI
control register 1 (SCC1), the transmitter and receiver relinquish control of the port
E pins.
19.4.2.3 Break Characters
Writing a logic 1 to the send break bit, SBK, in SCC2 loads the transmit shift
register with a break character. For TXINV = 0 (output not inverted), a transmitted
break character contains all logic 0s and has no start, stop, or parity bit. Break
character length depends on the M bit in SCC1 and the LINR bits in SCBR. As long
as SBK is at logic 1, transmitter logic continuously loads break characters into the
transmit shift register. After software clears the SBK bit, the shift register finishes
transmitting the last break character and then transmits at least one logic 1. The
automatic logic 1 at the end of a break character guarantees the recognition of the
start bit of the next character.
When LINR is cleared in SCBR, the ESCI recognizes a break character when a
start bit is followed by eight or nine logic 0 data bits and a logic 0 where the stop bit
should be, resulting in a total of 10 or 11 consecutive logic 0 data bits. When LINR
is set in SCBR, the ESCI recognizes a break character when a start bit is followed
by 9 or 10 logic 0 data bits and a logic 0 where the stop bit should be, resulting in
a total of 11 or 12 consecutive logic 0 data bits.
Receiving a break character has these effects on ESCI registers:
•
Sets the framing error bit (FE) in SCS1
•
Sets the ESCI receiver full bit (SCRF) in SCS1
•
Clears the ESCI data register (SCDR)
•
Clears the R8 bit in SCC3
•
Sets the break flag bit (BKF) in SCS2
•
May set the overrun (OR), noise flag (NF), parity error (PE),
or reception in progress flag (RPF) bits
MC68HC908GZ8
MOTOROLA
Data Sheet
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
225
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
19.4.2.4 Idle Characters
For TXINV = 0 (output not inverted), a transmitted idle character contains all logic
1s and has no start, stop, or parity bit. Idle character length depends on the M bit
in SCC1. The preamble is a synchronizing idle character that begins every
transmission.
Freescale Semiconductor, Inc...
If the TE bit is cleared during a transmission, the TxD pin becomes idle after
completion of the transmission in progress. Clearing and then setting the TE bit
during a transmission queues an idle character to be sent after the character
currently being transmitted.
NOTE:
When queueing an idle character, return the TE bit to logic 1 before the stop bit of
the current character shifts out to the TxD pin. Setting TE after the stop bit appears
on TxD causes data previously written to the SCDR to be lost. A good time to toggle
the TE bit for a queued idle character is when the SCTE bit becomes set and just
before writing the next byte to the SCDR.
19.4.2.5 Inversion of Transmitted Output
The transmit inversion bit (TXINV) in ESCI control register 1 (SCC1) reverses the
polarity of transmitted data. All transmitted values including idle, break, start,
and stop bits, are inverted when TXINV is at logic 1. See 19.8.1 ESCI Control
Register 1.
19.4.2.6 Transmitter Interrupts
These conditions can generate CPU interrupt requests from the ESCI transmitter:
•
ESCI transmitter empty (SCTE) — The SCTE bit in SCS1 indicates that the
SCDR has transferred a character to the transmit shift register. SCTE can
generate a transmitter CPU interrupt request. Setting the ESCI transmit
interrupt enable bit, SCTIE, in SCC2 enables the SCTE bit to generate
transmitter CPU interrupt requests.
•
Transmission complete (TC) — The TC bit in SCS1 indicates that the
transmit shift register and the SCDR are empty and that no break or idle
character has been generated. The transmission complete interrupt enable
bit, TCIE, in SCC2 enables the TC bit to generate transmitter CPU interrupt
requests.
19.4.3 Receiver
Figure 19-5 shows the structure of the ESCI receiver. The receiver I/O registers
are summarized in Figure 19-2.
Data Sheet
226
MC68HC908GZ8
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
Functional Description
INTERNAL BUS
SCR2
SCP0
SCR0
BUS CLOCK
PDS2
STOP
DATA
RECOVERY
ALL ZEROS
BKF
RPF
H
11-BIT
RECEIVE SHIFT REGISTER
8
7
6
5
4
3
2
1
0
L
PDS1
PDS0
PSSB3
PSSB2
CPU INTERRUPT
REQUEST
÷ 16
RxD
PSSB4
M
WAKE
ILTY
PSSB1
PEN
PSSB0
PTY
SCRF
WAKEUP
LOGIC
R8
PARITY
CHECKING
IDLE
ILIE
SCRF
SCRIE
RWU
IDLE
ILIE
SCRIE
OR
ORIE
ERROR CPU
INTERRUPT REQUEST
Freescale Semiconductor, Inc...
BAUD
DIVIDER
ALL ONES
PRESCALER
PRESCALER
÷4
ESCI DATA REGISTER
START
SCR1
MSB
LINR
SCP1
OR
ORIE
NF
NEIE
FE
FEIE
PE
PEIE
NF
NEIE
FE
FEIE
PE
PEIE
Figure 19-5. ESCI Receiver Block Diagram
MC68HC908GZ8
MOTOROLA
Data Sheet
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
227
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
19.4.3.1 Character Length
The receiver can accommodate either 8-bit or 9-bit data. The state of the M bit in
ESCI control register 1 (SCC1) determines character length. When receiving 9-bit
data, bit R8 in ESCI control register 3 (SCC3) is the ninth bit (bit 8). When receiving
8-bit data, bit R8 is a copy of the eighth bit (bit 7).
19.4.3.2 Character Reception
After a complete character shifts into the receive shift register, the data portion of
the character transfers to the SCDR. The ESCI receiver full bit, SCRF, in ESCI
status register 1 (SCS1) becomes set, indicating that the received byte can be
read. If the ESCI receive interrupt enable bit, SCRIE, in SCC2 is also set, the SCRF
bit generates a receiver CPU interrupt request.
19.4.3.3 Data Sampling
The receiver samples the RxD pin at the RT clock rate. The RT clock is an internal
signal with a frequency 16 times the baud rate. To adjust for baud rate mismatch,
the RT clock is resynchronized at these times (see Figure 19-6):
• After every start bit
• After the receiver detects a data bit change from logic 1 to logic 0 (after the
majority of data bit samples at RT8, RT9, and RT10 returns a valid logic 1
and the majority of the next RT8, RT9, and RT10 samples returns a valid
logic 0)
To locate the start bit, data recovery logic does an asynchronous search for a
logic 0 preceded by three logic 1s. When the falling edge of a possible start bit
occurs, the RT clock begins to count to 16.
START BIT
RxD
SAMPLES
START BIT
QUALIFICATION
LSB
START BIT
DATA
VERIFICATION SAMPLING
RT
CLOCK
RT CLOCK
STATE
RT1
RT1
RT1
RT1
RT1
RT1
RT1
RT1
RT1
RT2
RT3
RT4
RT5
RT6
RT7
RT8
RT9
RT10
RT11
RT12
RT13
RT14
RT15
RT16
RT1
RT2
RT3
RT4
Freescale Semiconductor, Inc...
During an ESCI reception, the receive shift register shifts characters in from the
RxD pin. The ESCI data register (SCDR) is the read-only buffer between the
internal data bus and the receive shift register.
RT CLOCK
RESET
Figure 19-6. Receiver Data Sampling
Data Sheet
228
MC68HC908GZ8
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
Functional Description
To verify the start bit and to detect noise, data recovery logic takes samples at RT3,
RT5, and RT7. Table 19-2 summarizes the results of the start bit verification
samples.
Freescale Semiconductor, Inc...
Table 19-2. Start Bit Verification
RT3, RT5, and RT7 Samples
Start Bit Verification
Noise Flag
000
Yes
0
001
Yes
1
010
Yes
1
011
No
0
100
Yes
1
101
No
0
110
No
0
111
No
0
If start bit verification is not successful, the RT clock is reset and a new search for
a start bit begins.
To determine the value of a data bit and to detect noise, recovery logic takes
samples at RT8, RT9, and RT10. Table 19-3 summarizes the results of the data
bit samples.
Table 19-3. Data Bit Recovery
NOTE:
RT8, RT9, and RT10 Samples
Data Bit Determination
Noise Flag
000
0
0
001
0
1
010
0
1
011
1
1
100
0
1
101
1
1
110
1
1
111
1
0
The RT8, RT9, and RT10 samples do not affect start bit verification. If any or all of
the RT8, RT9, and RT10 start bit samples are logic 1s following a successful start
bit verification, the noise flag (NF) is set and the receiver assumes that the bit is a
start bit.
To verify a stop bit and to detect noise, recovery logic takes samples at RT8, RT9,
and RT10. Table 19-4 summarizes the results of the stop bit samples.
MC68HC908GZ8
MOTOROLA
Data Sheet
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
229
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
RT8, RT9, and RT10 Samples
Framing Error Flag
Noise Flag
000
1
0
001
1
1
010
1
1
011
0
1
100
1
1
101
0
1
110
0
1
111
0
0
19.4.3.4 Framing Errors
If the data recovery logic does not detect a logic 1 where the stop bit should be in
an incoming character, it sets the framing error bit, FE, in SCS1. A break character
also sets the FE bit because a break character has no stop bit. The FE bit is set at
the same time that the SCRF bit is set.
19.4.3.5 Baud Rate Tolerance
A transmitting device may be operating at a baud rate below or above the receiver
baud rate. Accumulated bit time misalignment can cause one of the three stop bit
data samples to fall outside the actual stop bit. Then a noise error occurs. If more
than one of the samples is outside the stop bit, a framing error occurs. In most
applications, the baud rate tolerance is much more than the degree of
misalignment that is likely to occur.
As the receiver samples an incoming character, it resynchronizes the RT clock on
any valid falling edge within the character. Resynchronization within characters
corrects misalignments between transmitter bit times and receiver bit times.
Slow Data Tolerance
Figure 19-7 shows how much a slow received character can be misaligned
without causing a noise error or a framing error. The slow stop bit begins at RT8
instead of RT1 but arrives in time for the stop bit data samples at RT8, RT9, and
RT10.
MSB
STOP
RT16
RT15
RT14
RT13
RT12
RT11
RT10
RT9
RT8
RT7
RT6
RT5
RT4
RT3
RT2
RECEIVER
RT CLOCK
RT1
Freescale Semiconductor, Inc...
Table 19-4. Stop Bit Recovery
DATA
SAMPLES
Figure 19-7. Slow Data
Data Sheet
230
MC68HC908GZ8
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
Functional Description
For an 8-bit character, data sampling of the stop bit takes the receiver
9 bit times × 16 RT cycles + 10 RT cycles = 154 RT cycles.
With the misaligned character shown in Figure 19-7, the receiver counts 154
RT cycles at the point when the count of the transmitting device is 9 bit
times × 16 RT cycles + 3 RT cycles = 147 RT cycles.
The maximum percent difference between the receiver count and the
transmitter count of a slow 8-bit character with no errors is:
154 – 147 × 100 = 4.54%
-------------------------154
Freescale Semiconductor, Inc...
For a 9-bit character, data sampling of the stop bit takes the receiver
10 bit times × 16 RT cycles + 10 RT cycles = 170 RT cycles.
With the misaligned character shown in Figure 19-7, the receiver counts 170
RT cycles at the point when the count of the transmitting device is 10 bit
times × 16 RT cycles + 3 RT cycles = 163 RT cycles.
The maximum percent difference between the receiver count and the
transmitter count of a slow 9-bit character with no errors is:
170 – 163 × 100 = 4.12%
-------------------------170
Fast Data Tolerance
Figure 19-8 shows how much a fast received character can be misaligned
without causing a noise error or a framing error. The fast stop bit ends at RT10
instead of RT16 but is still there for the stop bit data samples at RT8, RT9, and
RT10.
STOP
IDLE OR NEXT CHARACTER
RT16
RT15
RT14
RT13
RT12
RT11
RT10
RT9
RT8
RT7
RT6
RT5
RT4
RT3
RT2
RT1
RECEIVER
RT CLOCK
DATA
SAMPLES
Figure 19-8. Fast Data
For an 8-bit character, data sampling of the stop bit takes the receiver
9 bit times × 16 RT cycles + 10 RT cycles = 154 RT cycles.
With the misaligned character shown in Figure 19-8, the receiver counts 154
RT cycles at the point when the count of the transmitting device is
10 bit times × 16 RT cycles = 160 RT cycles.
MC68HC908GZ8
MOTOROLA
Data Sheet
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
231
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
The maximum percent difference between the receiver count and the
transmitter count of a fast 8-bit character with no errors is
154 – 160 × 100 = 3.90%.
-------------------------154
Freescale Semiconductor, Inc...
For a 9-bit character, data sampling of the stop bit takes the receiver
10 bit times × 16 RT cycles + 10 RT cycles = 170 RT cycles.
With the misaligned character shown in Figure 19-8, the receiver counts 170
RT cycles at the point when the count of the transmitting device is
11 bit times × 16 RT cycles = 176 RT cycles.
The maximum percent difference between the receiver count and the
transmitter count of a fast 9-bit character with no errors is:
170 – 176 × 100 = 3.53%.
-------------------------170
19.4.3.6 Receiver Wakeup
So that the MCU can ignore transmissions intended only for other receivers in
multiple-receiver systems, the receiver can be put into a standby state. Setting the
receiver wakeup bit, RWU, in SCC2 puts the receiver into a standby state during
which receiver interrupts are disabled.
Depending on the state of the WAKE bit in SCC1, either of two conditions on the
RxD pin can bring the receiver out of the standby state:
1. Address mark — An address mark is a logic 1 in the MSB position of a
received character. When the WAKE bit is set, an address mark wakes the
receiver from the standby state by clearing the RWU bit. The address mark
also sets the ESCI receiver full bit, SCRF. Software can then compare the
character containing the address mark to the user-defined address of the
receiver. If they are the same, the receiver remains awake and processes
the characters that follow. If they are not the same, software can set the
RWU bit and put the receiver back into the standby state.
2. Idle input line condition — When the WAKE bit is clear, an idle character on
the RxD pin wakes the receiver from the standby state by clearing the RWU
bit. The idle character that wakes the receiver does not set the receiver idle
bit, IDLE, or the ESCI receiver full bit, SCRF. The idle line type bit, ILTY,
determines whether the receiver begins counting logic 1s as idle character
bits after the start bit or after the stop bit.
NOTE:
With the WAKE bit clear, setting the RWU bit after the RxD pin has been idle will
cause the receiver to wakeup.
Data Sheet
232
MC68HC908GZ8
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
Low-Power Modes
19.4.3.7 Receiver Interrupts
Freescale Semiconductor, Inc...
These sources can generate CPU interrupt requests from the ESCI receiver:
•
ESCI receiver full (SCRF) — The SCRF bit in SCS1 indicates that the
receive shift register has transferred a character to the SCDR. SCRF can
generate a receiver CPU interrupt request. Setting the ESCI receive
interrupt enable bit, SCRIE, in SCC2 enables the SCRF bit to generate
receiver CPU interrupts.
•
Idle input (IDLE) — The IDLE bit in SCS1 indicates that 10 or 11 consecutive
logic 1s shifted in from the RxD pin. The idle line interrupt enable bit, ILIE,
in SCC2 enables the IDLE bit to generate CPU interrupt requests.
19.4.3.8 Error Interrupts
These receiver error flags in SCS1 can generate CPU interrupt requests:
•
Receiver overrun (OR) — The OR bit indicates that the receive shift register
shifted in a new character before the previous character was read from the
SCDR. The previous character remains in the SCDR, and the new character
is lost. The overrun interrupt enable bit, ORIE, in SCC3 enables OR to
generate ESCI error CPU interrupt requests.
•
Noise flag (NF) — The NF bit is set when the ESCI detects noise on
incoming data or break characters, including start, data, and stop bits. The
noise error interrupt enable bit, NEIE, in SCC3 enables NF to generate ESCI
error CPU interrupt requests.
•
Framing error (FE) — The FE bit in SCS1 is set when a logic 0 occurs where
the receiver expects a stop bit. The framing error interrupt enable bit, FEIE,
in SCC3 enables FE to generate ESCI error CPU interrupt requests.
•
Parity error (PE) — The PE bit in SCS1 is set when the ESCI detects a parity
error in incoming data. The parity error interrupt enable bit, PEIE, in SCC3
enables PE to generate ESCI error CPU interrupt requests.
19.5 Low-Power Modes
The WAIT and STOP instructions put the MCU in low power-consumption standby
modes.
19.5.1 Wait Mode
The ESCI module remains active in wait mode. Any enabled CPU interrupt request
from the ESCI module can bring the MCU out of wait mode.
If ESCI module functions are not required during wait mode, reduce power
consumption by disabling the module before executing the WAIT instruction.
MC68HC908GZ8
MOTOROLA
Data Sheet
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
233
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
19.5.2 Stop Mode
The ESCI module is inactive in stop mode. The STOP instruction does not affect
ESCI register states. ESCI module operation resumes after the MCU exits stop
mode.
Because the internal clock is inactive during stop mode, entering stop mode during
an ESCI transmission or reception results in invalid data.
Freescale Semiconductor, Inc...
19.6 ESCI During Break Module Interrupts
The BCFE bit in the break flag control register (SBFCR) enables software to clear
status bits during the break state. See Section 6. Break Module (BRK).
To allow software to clear status bits during a break interrupt, write a logic 1 to the
BCFE bit. If a status bit is cleared during the break state, it remains cleared when
the MCU exits the break state.
To protect status bits during the break state, write a logic 0 to the BCFE bit. With
BCFE at logic 0 (its default state), software can read and write I/O registers during
the break state without affecting status bits. Some status bits have a two-step
read/write clearing procedure. If software does the first step on such a bit before
the break, the bit cannot change during the break state as long as BCFE is at logic
0. After the break, doing the second step clears the status bit.
19.7 I/O Signals
Port E shares two of its pins with the ESCI module. The two ESCI I/O pins are:
•
PTE0/TxD — transmit data
•
PTE1/RxD — receive data
19.7.1 PTE0/TxD (Transmit Data)
The PTE0/TxD pin is the serial data output from the ESCI transmitter. The ESCI
shares the PTE0/TxD pin with port E. When the ESCI is enabled, the PTE0/TxD
pin is an output regardless of the state of the DDRE0 bit in data direction register
E (DDRE).
19.7.2 PTE1/RxD (Receive Data)
The PTE1/RxD pin is the serial data input to the ESCI receiver. The ESCI shares
the PTE1/RxD pin with port E. When the ESCI is enabled, the PTE1/RxD pin is an
input regardless of the state of the DDRE1 bit in data direction register E (DDRE).
Data Sheet
234
MC68HC908GZ8
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
I/O Registers
19.8 I/O Registers
Freescale Semiconductor, Inc...
These I/O registers control and monitor ESCI operation:
•
ESCI control register 1, SCC1
•
ESCI control register 2, SCC2
•
ESCI control register 3, SCC3
•
ESCI status register 1, SCS1
•
ESCI status register 2, SCS2
•
ESCI data register, SCDR
•
ESCI baud rate register, SCBR
•
ESCI prescaler register, SCPSC
•
ESCI arbiter control register, SCIACTL
•
ESCI arbiter data register, SCIADAT
19.8.1 ESCI Control Register 1
ESCI control register 1 (SCC1):
•
Enables loop mode operation
•
Enables the ESCI
•
Controls output polarity
•
Controls character length
•
Controls ESCI wakeup method
•
Controls idle character detection
•
Enables parity function
•
Controls parity type
:
Address: $0013
Read:
Write:
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
LOOPS
ENSCI
TXINV
M
WAKE
ILTY
PEN
PTY
0
0
0
0
0
0
0
0
Figure 19-9. ESCI Control Register 1 (SCC1)
LOOPS — Loop Mode Select Bit
This read/write bit enables loop mode operation. In loop mode the RxD pin is
disconnected from the ESCI, and the transmitter output goes into the receiver
input. Both the transmitter and the receiver must be enabled to use loop mode.
Reset clears the LOOPS bit.
1 = Loop mode enabled
0 = Normal operation enabled
MC68HC908GZ8
MOTOROLA
Data Sheet
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
235
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
ENSCI — Enable ESCI Bit
This read/write bit enables the ESCI and the ESCI baud rate generator. Clearing
ENSCI sets the SCTE and TC bits in ESCI status register 1 and disables
transmitter interrupts. Reset clears the ENSCI bit.
1 = ESCI enabled
0 = ESCI disabled
Freescale Semiconductor, Inc...
TXINV — Transmit Inversion Bit
This read/write bit reverses the polarity of transmitted data. Reset clears the
TXINV bit.
1 = Transmitter output inverted
0 = Transmitter output not inverted
NOTE:
Setting the TXINV bit inverts all transmitted values including idle, break, start, and
stop bits.
M — Mode (Character Length) Bit
This read/write bit determines whether ESCI characters are eight or nine bits
long (See Table 19-5).The ninth bit can serve as a receiver wakeup signal or as
a parity bit. Reset clears the M bit.
1 = 9-bit ESCI characters
0 = 8-bit ESCI characters
Table 19-5. Character Format Selection
Control Bits
Character Format
M
PEN:PTY
Start
Bits
Data
Bits
Parity
Stop
Bits
Character
Length
0
0 X
1
8
None
1
10 bits
1
0 X
1
9
None
1
11 bits
0
1 0
1
7
Even
1
10 bits
0
1 1
1
7
Odd
1
10 bits
1
1 0
1
8
Even
1
11 bits
1
1 1
1
8
Odd
1
11 bits
WAKE — Wakeup Condition Bit
This read/write bit determines which condition wakes up the ESCI: a logic 1
(address mark) in the MSB position of a received character or an idle condition
on the RxD pin. Reset clears the WAKE bit.
1 = Address mark wakeup
0 = Idle line wakeup
ILTY — Idle Line Type Bit
This read/write bit determines when the ESCI starts counting logic 1s as idle
character bits. The counting begins either after the start bit or after the stop bit.
If the count begins after the start bit, then a string of logic 1s preceding the stop
Data Sheet
236
MC68HC908GZ8
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
I/O Registers
bit may cause false recognition of an idle character. Beginning the count after
the stop bit avoids false idle character recognition, but requires properly
synchronized transmissions. Reset clears the ILTY bit.
1 = Idle character bit count begins after stop bit
0 = Idle character bit count begins after start bit
Freescale Semiconductor, Inc...
PEN — Parity Enable Bit
This read/write bit enables the ESCI parity function (see Table 19-5). When
enabled, the parity function inserts a parity bit in the MSB position (see Table
19-3). Reset clears the PEN bit.
1 = Parity function enabled
0 = Parity function disabled
PTY — Parity Bit
This read/write bit determines whether the ESCI generates and checks for odd
parity or even parity (see Table 19-5). Reset clears the PTY bit.
1 = Odd parity
0 = Even parity
NOTE:
Changing the PTY bit in the middle of a transmission or reception can generate a
parity error.
19.8.2 ESCI Control Register 2
ESCI control register 2 (SCC2):
•
Enables these CPU interrupt requests:
– SCTE bit to generate transmitter CPU interrupt requests
– TC bit to generate transmitter CPU interrupt requests
– SCRF bit to generate receiver CPU interrupt requests
– IDLE bit to generate receiver CPU interrupt requests
•
Enables the transmitter
•
Enables the receiver
•
Enables ESCI wakeup
•
Transmits ESCI break characters
Address: $0014
Read:
Write:
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
SCTIE
TCIE
SCRIE
ILIE
TE
RE
RWU
SBK
0
0
0
0
0
0
0
0
Figure 19-10. ESCI Control Register 2 (SCC2)
MC68HC908GZ8
MOTOROLA
Data Sheet
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
237
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
SCTIE — ESCI Transmit Interrupt Enable Bit
This read/write bit enables the SCTE bit to generate ESCI transmitter CPU
interrupt requests. Setting the SCTIE bit in SCC2 enables the SCTE bit to
generate CPU interrupt requests. Reset clears the SCTIE bit.
1 = SCTE enabled to generate CPU interrupt
0 = SCTE not enabled to generate CPU interrupt
Freescale Semiconductor, Inc...
TCIE — Transmission Complete Interrupt Enable Bit
This read/write bit enables the TC bit to generate ESCI transmitter CPU
interrupt requests. Reset clears the TCIE bit.
1 = TC enabled to generate CPU interrupt requests
0 = TC not enabled to generate CPU interrupt requests
SCRIE — ESCI Receive Interrupt Enable Bit
This read/write bit enables the SCRF bit to generate ESCI receiver CPU
interrupt requests. Setting the SCRIE bit in SCC2 enables the SCRF bit to
generate CPU interrupt requests. Reset clears the SCRIE bit.
1 = SCRF enabled to generate CPU interrupt
0 = SCRF not enabled to generate CPU interrupt
ILIE — Idle Line Interrupt Enable Bit
This read/write bit enables the IDLE bit to generate ESCI receiver CPU interrupt
requests. Reset clears the ILIE bit.
1 = IDLE enabled to generate CPU interrupt requests
0 = IDLE not enabled to generate CPU interrupt requests
TE — Transmitter Enable Bit
Setting this read/write bit begins the transmission by sending a preamble of 10
or 11 logic 1s from the transmit shift register to the TxD pin. If software clears
the TE bit, the transmitter completes any transmission in progress before the
TxD returns to the idle condition (logic 1). Clearing and then setting TE during a
transmission queues an idle character to be sent after the character currently
being transmitted. Reset clears the TE bit.
1 = Transmitter enabled
0 = Transmitter disabled
NOTE:
Writing to the TE bit is not allowed when the enable ESCI bit (ENSCI) is clear.
ENSCI is in ESCI control register 1.
RE — Receiver Enable Bit
Setting this read/write bit enables the receiver. Clearing the RE bit disables the
receiver but does not affect receiver interrupt flag bits. Reset clears the RE bit.
1 = Receiver enabled
0 = Receiver disabled
NOTE:
Writing to the RE bit is not allowed when the enable ESCI bit (ENSCI) is clear.
ENSCI is in ESCI control register 1.
Data Sheet
238
MC68HC908GZ8
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
I/O Registers
Freescale Semiconductor, Inc...
RWU — Receiver Wakeup Bit
This read/write bit puts the receiver in a standby state during which receiver
interrupts are disabled. The WAKE bit in SCC1 determines whether an idle input
or an address mark brings the receiver out of the standby state and clears the
RWU bit. Reset clears the RWU bit.
1 = Standby state
0 = Normal operation
SBK — Send Break Bit
Setting and then clearing this read/write bit transmits a break character followed
by a logic 1. The logic 1 after the break character guarantees recognition of a
valid start bit. If SBK remains set, the transmitter continuously transmits break
characters with no logic 1s between them. Reset clears the SBK bit.
1 = Transmit break characters
0 = No break characters being transmitted
NOTE:
Do not toggle the SBK bit immediately after setting the SCTE bit. Toggling SBK
before the preamble begins causes the ESCI to send a break character instead of
a preamble.
19.8.3 ESCI Control Register 3
ESCI control register 3 (SCC3):
•
Stores the ninth ESCI data bit received and the ninth ESCI data bit to be
transmitted.
•
Enables these interrupts:
– Receiver overrun
– Noise error
– Framing error
– Parity error
Address:
$0015
Bit 7
Read:
R8
Write:
Reset:
U
6
5
4
3
2
1
Bit 0
T8
R
R
ORIE
NEIE
FEIE
PEIE
0
0
0
0
0
= Unimplemented
0
0
R
= Reserved
U = Unaffected
Figure 19-11. ESCI Control Register 3 (SCC3)
R8 — Received Bit 8
When the ESCI is receiving 9-bit characters, R8 is the read-only ninth bit (bit 8)
of the received character. R8 is received at the same time that the SCDR
receives the other 8 bits.
MC68HC908GZ8
MOTOROLA
Data Sheet
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
239
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
When the ESCI is receiving 8-bit characters, R8 is a copy of the eighth bit (bit 7).
Reset has no effect on the R8 bit.
Freescale Semiconductor, Inc...
T8 — Transmitted Bit 8
When the ESCI is transmitting 9-bit characters, T8 is the read/write ninth bit (bit
8) of the transmitted character. T8 is loaded into the transmit shift register at the
same time that the SCDR is loaded into the transmit shift register. Reset clears
the T8 bit.
ORIE — Receiver Overrun Interrupt Enable Bit
This read/write bit enables ESCI error CPU interrupt requests generated by the
receiver overrun bit, OR. Reset clears ORIE.
1 = ESCI error CPU interrupt requests from OR bit enabled
0 = ESCI error CPU interrupt requests from OR bit disabled
NEIE — Receiver Noise Error Interrupt Enable Bit
This read/write bit enables ESCI error CPU interrupt requests generated by the
noise error bit, NE. Reset clears NEIE.
1 = ESCI error CPU interrupt requests from NE bit enabled
0 = ESCI error CPU interrupt requests from NE bit disabled
FEIE — Receiver Framing Error Interrupt Enable Bit
This read/write bit enables ESCI error CPU interrupt requests generated by the
framing error bit, FE. Reset clears FEIE.
1 = ESCI error CPU interrupt requests from FE bit enabled
0 = ESCI error CPU interrupt requests from FE bit disabled
PEIE — Receiver Parity Error Interrupt Enable Bit
This read/write bit enables ESCI receiver CPU interrupt requests generated by
the parity error bit, PE. Reset clears PEIE.
1 = ESCI error CPU interrupt requests from PE bit enabled
0 = ESCI error CPU interrupt requests from PE bit disabled
19.8.4 ESCI Status Register 1
ESCI status register 1 (SCS1) contains flags to signal these conditions:
•
Transfer of SCDR data to transmit shift register complete
•
Transmission complete
•
Transfer of receive shift register data to SCDR complete
•
Receiver input idle
•
Receiver overrun
•
Noisy data
•
Framing error
•
Parity error
Data Sheet
240
MC68HC908GZ8
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
I/O Registers
Address:
Read:
$0016
Bit 7
6
5
4
3
2
1
Bit 0
SCTE
TC
SCRF
IDLE
OR
NF
FE
PE
1
1
0
0
0
0
0
0
Write:
Reset:
= Unimplemented
Figure 19-12. ESCI Status Register 1 (SCS1)
Freescale Semiconductor, Inc...
SCTE — ESCI Transmitter Empty Bit
This clearable, read-only bit is set when the SCDR transfers a character to the
transmit shift register. SCTE can generate an ESCI transmitter CPU interrupt
request. When the SCTIE bit in SCC2 is set, SCTE generates an ESCI
transmitter CPU interrupt request. In normal operation, clear the SCTE bit by
reading SCS1 with SCTE set and then writing to SCDR. Reset sets the
SCTE bit.
1 = SCDR data transferred to transmit shift register
0 = SCDR data not transferred to transmit shift register
TC — Transmission Complete Bit
This read-only bit is set when the SCTE bit is set, and no data, preamble, or
break character is being transmitted. TC generates an ESCI transmitter CPU
interrupt request if the TCIE bit in SCC2 is also set. TC is cleared automatically
when data, preamble, or break is queued and ready to be sent. There may be
up to 1.5 transmitter clocks of latency between queueing data, preamble, and
break and the transmission actually starting. Reset sets the TC bit.
1 = No transmission in progress
0 = Transmission in progress
SCRF — ESCI Receiver Full Bit
This clearable, read-only bit is set when the data in the receive shift register
transfers to the ESCI data register. SCRF can generate an ESCI receiver CPU
interrupt request. When the SCRIE bit in SCC2 is set the SCRF generates a
CPU interrupt request. In normal operation, clear the SCRF bit by reading SCS1
with SCRF set and then reading the SCDR. Reset clears SCRF.
1 = Received data available in SCDR
0 = Data not available in SCDR
IDLE — Receiver Idle Bit
This clearable, read-only bit is set when 10 or 11 consecutive logic 1s appear
on the receiver input. IDLE generates an ESCI receiver CPU interrupt request
if the ILIE bit in SCC2 is also set. Clear the IDLE bit by reading SCS1 with IDLE
set and then reading the SCDR. After the receiver is enabled, it must receive a
valid character that sets the SCRF bit before an idle condition can set the IDLE
bit. Also, after the IDLE bit has been cleared, a valid character must again set
the SCRF bit before an idle condition can set the IDLE bit. Reset clears the
IDLE bit.
1 = Receiver input idle
0 = Receiver input active (or idle since the IDLE bit was cleared)
MC68HC908GZ8
MOTOROLA
Data Sheet
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
241
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
Freescale Semiconductor, Inc...
OR — Receiver Overrun Bit
This clearable, read-only bit is set when software fails to read the SCDR before
the receive shift register receives the next character. The OR bit generates an
ESCI error CPU interrupt request if the ORIE bit in SCC3 is also set. The data
in the shift register is lost, but the data already in the SCDR is not affected. Clear
the OR bit by reading SCS1 with OR set and then reading the SCDR. Reset
clears the OR bit.
1 = Receive shift register full and SCRF = 1
0 = No receiver overrun
Software latency may allow an overrun to occur between reads of SCS1 and
SCDR in the flag-clearing sequence. Figure 19-13 shows the normal
flag-clearing sequence and an example of an overrun caused by a delayed
flag-clearing sequence. The delayed read of SCDR does not clear the OR bit
because OR was not set when SCS1 was read. Byte 2 caused the overrun and
is lost. The next flag-clearing sequence reads byte 3 in the SCDR instead of
byte 2.
In applications that are subject to software latency or in which it is important to
know which byte is lost due to an overrun, the flag-clearing routine can check
the OR bit in a second read of SCS1 after reading the data register.
BYTE 1
BYTE 2
BYTE 3
SCRF = 0
SCRF = 1
SCRF = 0
SCRF = 1
SCRF = 0
SCRF = 1
NORMAL FLAG CLEARING SEQUENCE
BYTE 4
READ SCS1
SCRF = 1
OR = 0
READ SCS1
SCRF = 1
OR = 0
READ SCS1
SCRF = 1
OR = 0
READ SCDR
BYTE 1
READ SCDR
BYTE 2
READ SCDR
BYTE 3
BYTE 1
BYTE 2
BYTE 3
SCRF = 0
OR = 0
SCRF = 1
OR = 1
SCRF = 0
OR = 1
SCRF = 1
SCRF = 1
OR = 1
DELAYED FLAG CLEARING SEQUENCE
BYTE 4
READ SCS1
SCRF = 1
OR = 0
READ SCS1
SCRF = 1
OR = 1
READ SCDR
BYTE 1
READ SCDR
BYTE 3
Figure 19-13. Flag Clearing Sequence
Data Sheet
242
MC68HC908GZ8
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
I/O Registers
Freescale Semiconductor, Inc...
NF — Receiver Noise Flag Bit
This clearable, read-only bit is set when the ESCI detects noise on the RxD pin.
NF generates an NF CPU interrupt request if the NEIE bit in SCC3 is also set.
Clear the NF bit by reading SCS1 and then reading the SCDR. Reset clears the
NF bit.
1 = Noise detected
0 = No noise detected
FE — Receiver Framing Error Bit
This clearable, read-only bit is set when a logic 0 is accepted as the stop bit. FE
generates an ESCI error CPU interrupt request if the FEIE bit in SCC3 also is
set. Clear the FE bit by reading SCS1 with FE set and then reading the SCDR.
Reset clears the FE bit.
1 = Framing error detected
0 = No framing error detected
PE — Receiver Parity Error Bit
This clearable, read-only bit is set when the ESCI detects a parity error in
incoming data. PE generates a PE CPU interrupt request if the PEIE bit in SCC3
is also set. Clear the PE bit by reading SCS1 with PE set and then reading the
SCDR. Reset clears the PE bit.
1 = Parity error detected
0 = No parity error detected
19.8.5 ESCI Status Register 2
ESCI status register 2 (SCS2) contains flags to signal these conditions:
•
Break character detected
•
Incoming data
Address:
Read:
$0017
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
BKF
RPF
0
0
0
0
0
0
0
0
Write:
Reset:
= Unimplemented
Figure 19-14. ESCI Status Register 2 (SCS2)
BKF — Break Flag Bit
This clearable, read-only bit is set when the ESCI detects a break character on
the RxD pin. In SCS1, the FE and SCRF bits are also set. In 9-bit character
transmissions, the R8 bit in SCC3 is cleared. BKF does not generate a CPU
interrupt request. Clear BKF by reading SCS2 with BKF set and then reading
the SCDR. Once cleared, BKF can become set again only after logic 1s again
appear on the RxD pin followed by another break character. Reset clears the
BKF bit.
1 = Break character detected
0 = No break character detected
MC68HC908GZ8
MOTOROLA
Data Sheet
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
243
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
RPF — Reception in Progress Flag Bit
This read-only bit is set when the receiver detects a logic 0 during the RT1 time
period of the start bit search. RPF does not generate an interrupt request. RPF
is reset after the receiver detects false start bits (usually from noise or a baud
rate mismatch), or when the receiver detects an idle character. Polling RPF
before disabling the ESCI module or entering stop mode can show whether a
reception is in progress.
1 = Reception in progress
0 = No reception in progress
Freescale Semiconductor, Inc...
19.8.6 ESCI Data Register
The ESCI data register (SCDR) is the buffer between the internal data bus and the
receive and transmit shift registers. Reset has no effect on data in the ESCI data
register.
Address:
$0018
Bit 7
6
5
4
3
2
1
Bit 0
Read:
R7
R6
R5
R4
R3
R2
R1
R0
Write:
T7
T6
T5
T4
T3
T2
T1
T0
Reset:
Unaffected by reset
Figure 19-15. ESCI Data Register (SCDR)
R7/T7:R0/T0 — Receive/Transmit Data Bits
Reading address $0018 accesses the read-only received data bits, R7:R0.
Writing to address $0018 writes the data to be transmitted, T7:T0. Reset has no
effect on the ESCI data register.
NOTE:
Do not use read-modify-write instructions on the ESCI data register.
19.8.7 ESCI Baud Rate Register
The ESCI baud rate register (SCBR) together with the ESCI prescaler register
selects the baud rate for both the receiver and the transmitter.
NOTE:
There are two prescalers available to adjust the baud rate. One in the ESCI baud
rate register and one in the ESCI prescaler register.
Address:
Read:
Write:
Reset:
$0019
Bit 7
6
5
4
3
2
1
Bit 0
LINT
LINR
SCP1
SCP0
R
SCR2
SCR1
SCR0
0
0
0
0
0
0
0
0
R
= Reserved
= Unimplemented
Figure 19-16. ESCI Baud Rate Register (SCBR)
Data Sheet
244
MC68HC908GZ8
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
I/O Registers
LINT — LIN Break Symbol Transmit Enable
This read/write bit selects the enhanced ESCI features for master nodes in the
local interconnect network (LIN) protocol (version 1.2) as shown in Table 19-6.
Reset clears LINT.
Freescale Semiconductor, Inc...
Table 19-6. ESCI LIN Master Node Control Bits
NOTE:
LINT
M
Functionality
0
X
Normal ESCI functionality
1
0
13-bit generation enabled for LIN transmitter
1
1
14-bit generation enabled for LIN transmitter
LIN master nodes require significantly tighter timing tolerances than slave nodes.
Be sure to consult the current LIN specification to ensure that timing requirements
are met properly. Generally, these timing tolerances require crystals or oscillators
to be used, rather than internal clocking circuits.
LINR — LIN Break Symbol Receiver Bits
This read/write bit selects the enhanced ESCI features for slave nodes in the
local interconnect network (LIN) protocol as shown in Table 19-7. Reset clears
LINR.
Table 19-7. ESCI LIN Slave Node Control Bits
LINR
M
Functionality
0
X
Normal ESCI functionality
1
0
11-bit break detect enabled for LIN receiver
1
1
12-bit break detect enabled for LIN receiver
In LIN (version 1.2) systems, the master node transmits a break character which
will appear as 11.05–14.95 dominant bits to the slave node. A data character of
0x00 sent from the master might appear as 7.65–10.35 dominant bit times. This
is due to the oscillator tolerance requirement that the slave node must be within
±15% of the master node's oscillator. Since a slave node cannot know if it is
running faster or slower than the master node (prior to synchronization), the
LINR bit allows the slave node to differentiate between a 0x00 character of
10.35 bits and a break character of 11.05 bits. The break symbol length must be
verified in software in any case, but the LINR bit serves as a filter, preventing
false detections of break characters that are really 0x00 data characters.
MC68HC908GZ8
MOTOROLA
Data Sheet
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
245
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
SCP1 and SCP0 — ESCI Baud Rate Register Prescaler Bits
These read/write bits select the baud rate register prescaler divisor as shown in
Table 19-8. Reset clears SCP1 and SCP0.
Freescale Semiconductor, Inc...
Table 19-8. ESCI Baud Rate Prescaling
SCP[1:0]
Baud Rate Register
Prescaler Divisor (BPD)
0 0
1
0 1
3
1 0
4
1 1
13
SCR2–SCR0 — ESCI Baud Rate Select Bits
These read/write bits select the ESCI baud rate divisor as shown in Table 19-9.
Reset clears SCR2–SCR0.
Table 19-9. ESCI Baud Rate Selection
SCR[2:1:0]
Baud Rate Divisor (BD)
0 0 0
1
0 0 1
2
0 1 0
4
0 1 1
8
1 0 0
16
1 0 1
32
1 1 0
64
1 1 1
128
19.8.8 ESCI Prescaler Register
The ESCI prescaler register (SCPSC) together with the ESCI baud rate register
selects the baud rate for both the receiver and the transmitter.
NOTE:
There are two prescalers available to adjust the baud rate. One in the ESCI baud
rate register and one in the ESCI prescaler register.
Address:
Read:
Write:
Reset:
$0009
Bit 7
6
5
4
3
2
1
Bit 0
PDS2
PDS1
PDS0
PSSB4
PSSB3
PSSB2
PSSB1
PSSB0
0
0
0
0
0
0
0
0
Figure 19-17. ESCI Prescaler Register (SCPSC)
Data Sheet
246
MC68HC908GZ8
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
I/O Registers
PDS2–PDS0 — Prescaler Divisor Select Bits
These read/write bits select the prescaler divisor as shown in
Table 19-10. Reset clears PDS2–PDS0.
NOTE:
The setting of ‘000’ will bypass this prescaler. It is not recommended to bypass the
prescaler while ENSCI is set, because the switching is not glitch free.
Freescale Semiconductor, Inc...
Table 19-10. ESCI Prescaler Division Ratio
PS[2:1:0]
Prescaler Divisor (PD)
0 0 0
Bypass this prescaler
0 0 1
2
0 1 0
3
0 1 1
4
1 0 0
5
1 0 1
6
1 1 0
7
1 1 1
8
PSSB4–PSSB0 — Clock Insertion Select Bits
These read/write bits select the number of clocks inserted in each 32 output
cycle frame to achieve more timing resolution on the average prescaler
frequency as shown in Table 19-11. Reset clears PSSB4–PSSB0.
Use the following formula to calculate the ESCI baud rate:
f Bus
Baud rate = -----------------------------------------------------------------------------------64 × BPD × BD × ( PD + PDFA )
where:
fBus = Bus frequency
BPD = Baud rate register prescaler divisor
BD = Baud rate divisor
PD = Prescaler divisor
PDFA = Prescaler divisor fine adjust
Table 19-12 shows the ESCI baud rates that can be generated with a 4.9152-MHz
bus frequency.
MC68HC908GZ8
MOTOROLA
Data Sheet
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
247
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
Table 19-11. ESCI Prescaler Divisor Fine Adjust
Freescale Semiconductor, Inc...
PSSB[4:3:2:1:0]
Prescaler Divisor Fine Adjust (PDFA)
0 0 0 0 0
0/32 = 0
0 0 0 0 1
1/32 = 0.03125
0 0 0 1 0
2/32 = 0.0625
0 0 0 1 1
3/32 = 0.09375
0 0 1 0 0
4/32 = 0.125
0 0 1 0 1
5/32 = 0.15625
0 0 1 1 0
6/32 = 0.1875
0 0 1 1 1
7/32 = 0.21875
0 1 0 0 0
8/32 = 0.25
0 1 0 0 1
9/32 = 0.28125
0 1 0 1 0
10/32 = 0.3125
0 1 0 1 1
11/32 = 0.34375
0 1 1 0 0
12/32 = 0.375
0 1 1 0 1
13/32 = 0.40625
0 1 1 1 0
14/32 = 0.4375
0 1 1 1 1
15/32 = 0.46875
1 0 0 0 0
16/32 = 0.5
1 0 0 0 1
17/32 = 0.53125
1 0 0 1 0
18/32 = 0.5625
1 0 0 1 1
19/32 = 0.59375
1 0 1 0 0
20/32 = 0.625
1 0 1 0 1
21/32 = 0.65625
1 0 1 1 0
22/32 = 0.6875
1 0 1 1 1
23/32 = 0.71875
1 1 0 0 0
24/32 = 0.75
1 1 0 0 1
25/32 = 0.78125
1 1 0 1 0
26/32 = 0.8125
1 1 0 1 1
27/32 = 0.84375
1 1 1 0 0
28/32 = 0.875
1 1 1 0 1
29/32 = 0.90625
1 1 1 1 0
30/32 = 0.9375
1 1 1 1 1
31/32 = 0.96875
Data Sheet
248
MC68HC908GZ8
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
I/O Registers
Freescale Semiconductor, Inc...
Table 19-12. ESCI Baud Rate Selection Examples
PS[2:1:0]
PSSB[4:3:2:1:0]
SCP[1:0]
Prescaler
Divisor
(BPD)
SCR[2:1:0]
Baud Rate
Divisor
(BD)
Baud Rate
(fBus= 4.9152 MHz)
0 0 0
X X X X X
0 0
1
0 0 0
1
76,800
1 1 1
0 0 0 0 0
0 0
1
0 0 0
1
9600
1 1 1
0 0 0 0 1
0 0
1
0 0 0
1
9562.65
1 1 1
0 0 0 1 0
0 0
1
0 0 0
1
9525.58
1 1 1
1 1 1 1 1
0 0
1
0 0 0
1
8563.07
0 0 0
X X X X X
0 0
1
0 0 1
2
38,400
0 0 0
X X X X X
0 0
1
0 1 0
4
19,200
0 0 0
X X X X X
0 0
1
0 1 1
8
9600
0 0 0
X X X X X
0 0
1
1 0 0
16
4800
0 0 0
X X X X X
0 0
1
1 0 1
32
2400
0 0 0
X X X X X
0 0
1
1 1 0
64
1200
0 0 0
X X X X X
0 0
1
1 1 1
128
600
0 0 0
X X X X X
0 1
3
0 0 0
1
25,600
0 0 0
X X X X X
0 1
3
0 0 1
2
12,800
0 0 0
X X X X X
0 1
3
0 1 0
4
6400
0 0 0
X X X X X
0 1
3
0 1 1
8
3200
0 0 0
X X X X X
0 1
3
1 0 0
16
1600
0 0 0
X X X X X
0 1
3
1 0 1
32
800
0 0 0
X X X X X
0 1
3
1 1 0
64
400
0 0 0
X X X X X
0 1
3
1 1 1
128
200
0 0 0
X X X X X
1 0
4
0 0 0
1
19,200
0 0 0
X X X X X
1 0
4
0 0 1
2
9600
0 0 0
X X X X X
1 0
4
0 1 0
4
4800
0 0 0
X X X X X
1 0
4
0 1 1
8
2400
0 0 0
X X X X X
1 0
4
1 0 0
16
1200
0 0 0
X X X X X
1 0
4
1 0 1
32
600
0 0 0
X X X X X
1 0
4
1 1 0
64
300
0 0 0
X X X X X
1 0
4
1 1 1
128
150
0 0 0
X X X X X
1 1
13
0 0 0
1
5908
0 0 0
X X X X X
1 1
13
0 0 1
2
2954
0 0 0
X X X X X
1 1
13
0 1 0
4
1477
0 0 0
X X X X X
1 1
13
0 1 1
8
739
0 0 0
X X X X X
1 1
13
1 0 0
16
369
0 0 0
X X X X X
1 1
13
1 0 1
32
185
0 0 0
X X X X X
1 1
13
1 1 0
64
92
0 0 0
X X X X X
1 1
13
1 1 1
128
46
MC68HC908GZ8
MOTOROLA
Data Sheet
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
249
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
19.9 ESCI Arbiter
The ESCI module comprises an arbiter module designed to support software for
communication tasks as bus arbitration, baud rate recovery and break time
detection. The arbiter module consists of an 9-bit counter with 1-bit overflow and
control logic. The CPU can control operation mode via the ESCI arbiter control
register (SCIACTL).
19.9.1 ESCI Arbiter Control Register
Address:
$000A
Freescale Semiconductor, Inc...
Bit 7
Read:
Write:
Reset:
AM1
6
ALOST
0
0
5
4
AM0
ACLK
0
0
3
2
1
Bit 0
AFIN
ARUN
AROVFL
ARD8
0
0
0
0
= Unimplemented
Figure 19-18. ESCI Arbiter Control Register (SCIACTL)
AM1 and AM0 — Arbiter Mode Select Bits
These read/write bits select the mode of the arbiter module as shown in Table
19-13. Reset clears AM1 and AM0.
Table 19-13. ESCI Arbiter Selectable Modes
AM[1:0]
ESCI Arbiter Mode
0 0
Idle / counter reset
0 1
Bit time measurement
1 0
Bus arbitration
1 1
Reserved / do not use
ALOST — Arbitration Lost Flag
This read-only bit indicates loss of arbitration. Clear ALOST by writing a logic 0
to AM1. Reset clears ALOST.
ACLK — Arbiter Counter Clock Select Bit
This read/write bit selects the arbiter counter clock source.
Reset clears ACLK.
1 = Arbiter counter is clocked with one half of the ESCI input clock generated
by the ESCI prescaler
0 = Arbiter counter is clocked with one half of the bus clock
AFIN— Arbiter Bit Time Measurement Finish Flag
This read-only bit indicates bit time measurement has finished. Clear AFIN by
writing any value to SCIACTL. Reset clears AFIN.
1 = Bit time measurement has finished
0 = Bit time measurement not yet finished
Data Sheet
250
MC68HC908GZ8
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Enhanced Serial Communications Interface (ESCI) Module
ESCI Arbiter
ARUN— Arbiter Counter Running Flag
This read-only bit indicates the arbiter counter is running. Reset clears ARUN.
1 = Arbiter counter running
0 = Arbiter counter stopped
AROVFL— Arbiter Counter Overflow Bit
This read-only bit indicates an arbiter counter overflow. Clear AROVFL by
writing any value to SCIACTL. Writing logic 0s to AM1 and AM0 resets the
counter keeps it in this idle state. Reset clears AROVFL.
1 = Arbiter counter overflow has occurred
0 = No arbiter counter overflow has occurred
ARD8— Arbiter Counter MSB
This read-only bit is the MSB of the 9-bit arbiter counter. Clear ARD8 by writing
any value to SCIACTL. Reset clears ARD8.
19.9.2 ESCI Arbiter Data Register
Address: $000B
Read:
Bit 7
6
5
4
3
2
1
Bit 0
ARD7
ARD6
ARD5
ARD4
ARD3
ARD2
ARD1
ARD0
0
0
0
0
0
0
0
Write:
Reset:
0
= Unimplemented
Figure 19-19. ESCI Arbiter Data Register (SCIADAT)
ARD7–ARD0 — Arbiter Least Significant Counter Bits
These read-only bits are the eight LSBs of the 9-bit arbiter counter. Clear
ARD7–ARD0 by writing any value to SCIACTL. Writing logic 0s to AM1 and AM0
permanently resets the counter and keeps it in this idle state. Reset clears
ARD7–ARD0.
19.9.3 Bit Time Measurement
Two bit time measurement modes, described here, are available according to the
state of ACLK.
1. ACLK = 0 — The counter is clocked with one half of the bus clock. The
counter is started when a falling edge on the RxD pin is detected. The
counter will be stopped on the next falling edge. ARUN is set while the
counter is running, AFIN is set on the second falling edge on RxD (for
instance, the counter is stopped). This mode is used to recover the received
baud rate. See Figure 19-20.
2. ACLK = 1 — The counter is clocked with one half of the ESCI input clock
generated by the ESCI prescaler. The counter is started when a logic 0 is
detected on RxD (see Figure 19-21). A logic 0 on RxD on enabling the bit
time measurement with ACLK = 1 leads to immediate start of the counter
(see Figure 19-22). The counter will be stopped on the next rising edge of
RxD. This mode is used to measure the length of a received break.
MC68HC908GZ8
MOTOROLA
Data Sheet
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
251
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
MEASURED TIME
CPU READS RESULT
OUT OF SCIADAT
COUNTER STOPS,
AFIN = 1
COUNTER STARTS,
ARUN = 1
CPU WRITES SCIACTL
WITH $20
RXD
Freescale Semiconductor, Inc...
Figure 19-20. Bit Time Measurement with ACLK = 0
MEASURED TIME
CPU READS RESULT OUT
OF SCIADAT
COUNTER STOPS, AFIN = 1
CPU WRITES SCIACTL WITH $30
COUNTER STARTS, ARUN = 1
RXD
Figure 19-21. Bit Time Measurement with ACLK = 1, Scenario A
MEASURED TIME
CPU READS RESULT
OUT OF SCIADAT
COUNTER STOPS,
AFIN = 1
COUNTER STARTS,
ARUN = 1
CPU WRITES SCIACTL
WITH $30
RXD
Figure 19-22. Bit Time Measurement with ACLK = 1, Scenario B
Data Sheet
252
MC68HC908GZ8
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Enhanced Serial Communications Interface (ESCI) Module
ESCI Arbiter
19.9.4 Arbitration Mode
If AM[1:0] is set to 10, the arbiter module operates in arbitration mode. On every
rising edge of SCI_TxD (output of the ESCI module, internal chip signal), the
counter is started. When the counter reaches $38 (ACLK = 0) or $08 (ACLK = 1),
RxD is statically sensed. If in this case, RxD is sensed low (for example, another
bus is driving the bus dominant) ALOST is set. As long as ALOST is set, the TxD
pin is forced to 1, resulting in a seized transmission.
Freescale Semiconductor, Inc...
If SCI_TxD is sensed logic 0 without having sensed a logic 0 before on RxD, the
counter will be reset, arbitration operation will be restarted after the next rising edge
of SCI_TxD.
MC68HC908GZ8
MOTOROLA
Data Sheet
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
253
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Enhanced Serial Communications Interface (ESCI) Module
Data Sheet
254
MC68HC908GZ8
Enhanced Serial Communications Interface (ESCI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 20. System Integration Module (SIM)
20.1 Introduction
Freescale Semiconductor, Inc...
This section describes the system integration module (SIM). Together with the
central processor unit (CPU), the SIM controls all microcontroller unit (MCU)
activities. A block diagram of the SIM is shown in Figure 20-1. Table 20-1 is a
summary of the SIM input/output (I/O) registers. The SIM is a system state
controller that coordinates CPU and exception timing.
The SIM is responsible for:
•
Bus clock generation and control for CPU and peripherals:
– Stop/wait/reset/break entry and recovery
– Internal clock control
•
Master reset control, including power-on reset (POR) and computer
operating properly (COP) timeout
•
Interrupt control:
– Acknowledge timing
– Arbitration control timing
– Vector address generation
•
CPU enable/disable timing
•
Modular architecture expandable to 128 interrupt sources
Table 20-1 shows the internal signal names used in this section.
MC68HC908GZ8
MOTOROLA
Data Sheet
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
255
Freescale Semiconductor, Inc.
System Integration Module (SIM)
MODULE STOP
MODULE WAIT
CPU STOP (FROM CPU)
CPU WAIT (FROM CPU)
STOP/WAIT
CONTROL
SIMOSCEN (TO CGM)
SIM
COUNTER
CGMXCLK (FROM CGM)
CGMOUT (FROM CGM)
Freescale Semiconductor, Inc...
÷2
CLOCK
CONTROL
VDD
CLOCK GENERATORS
INTERNAL
PULLUP
DEVICE
RESET
PIN LOGIC
INTERNAL CLOCKS
FORCED MONITOR MODE ENTRY
LVI (FROM LVI MODULE)
POR CONTROL
MASTER
RESET
CONTROL
RESET PIN CONTROL
SIM RESET STATUS REGISTER
ILLEGAL OPCODE (FROM CPU)
ILLEGAL ADDRESS (FROM ADDRESS
MAP DECODERS)
COP (FROM COP MODULE)
RESET
INTERRUPT SOURCES
INTERRUPT CONTROL
AND PRIORITY DECODE
CPU INTERFACE
Figure 20-1. SIM Block Diagram
Table 20-1. Signal Name Conventions
Signal Name
Description
CGMXCLK
Buffered version of OSC1 from clock generator module (CGM)
CGMVCLK
PLL output
CGMOUT
PLL-based or OSC1-based clock output from CGM module
(Bus clock = CGMOUT divided by two)
IAB
Internal address bus
IDB
Internal data bus
PORRST
Signal from the power-on reset module to the SIM
IRST
Internal reset signal
R/W
Read/write signal
Data Sheet
256
MC68HC908GZ8
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
System Integration Module (SIM)
SIM Bus Clock Control and Generation
Addr.
Register Name
SIM Break Status Read:
Register (SBSR) Write:
See page 271. Reset:
$FE00
Bit 7
6
5
4
3
2
1
Bit 0
R
R
R
R
R
R
0
0
0
0
0
0
0
0
SBSW
R
Note(1)
1. Writing a logic 0 clears SBSW.
SIM Reset Status Read:
Register (SRSR) Write:
See page 272. POR:
Freescale Semiconductor, Inc...
$FE01
$FE03
SIM Break Flag Control Reg- Read:
ister (SBFCR) Write:
See page 273. Reset:
POR
PIN
COP
ILOP
ILAD
MODRST
LVI
0
1
0
0
0
0
0
0
0
BCFE
R
R
R
R
R
R
R
0
Interrupt Status Read:
Register 1 (INT1) Write:
See page 267. Reset:
IF6
IF5
IF4
IF3
IF2
IF1
0
0
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
IF14
IF13
IF12
IF11
IF10
IF9
IF8
IF7
$FE05
Interrupt Status Read:
Register 2 (INT2) Write:
See page 267. Reset:
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
0
0
IF20
IF19
IF18
IF17
IF16
IF15
$FE06
Interrupt Status Read:
Register 3 (INT3) Write:
See page 267. Reset:
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
R
= Reserved
$FE04
= Unimplemented
Figure 20-2. SIM I/O Register Summary
20.2 SIM Bus Clock Control and Generation
The bus clock generator provides system clock signals for the CPU and peripherals
on the MCU. The system clocks are generated from an incoming clock, CGMOUT,
as shown in Figure 20-3. This clock originates from either an external oscillator or
from the on-chip PLL.
20.2.1 Bus Timing
In user mode, the internal bus frequency is either the crystal oscillator output
(CGMXCLK) divided by four or the PLL output (CGMVCLK) divided by four.
20.2.2 Clock Startup from POR or LVI Reset
When the power-on reset module or the low-voltage inhibit module generates a
reset, the clocks to the CPU and peripherals are inactive and held in an inactive
phase until after the 4096 CGMXCLK cycle POR timeout has completed. The RST
pin is driven low by the SIM during this entire period. The IBUS clocks start upon
completion of the timeout.
MC68HC908GZ8
MOTOROLA
Data Sheet
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
257
Freescale Semiconductor, Inc.
System Integration Module (SIM)
OSC2
OSCILLATOR (OSC)
CGMXCLK
TO TBM,TIM1,TIM2, ADC, MSCAN
OSC1
SIM
Freescale Semiconductor, Inc...
OSCENINSTOP
FROM
CONFIG
SIM COUNTER
CGMRCLK
CGMOUT
÷2
PHASE-LOCKED LOOP (PLL)
BUS CLOCK
GENERATORS
SIMOSCEN
IT12
TO REST
OF CHIP
IT23
TO REST
OF CHIP
TO MSCAN
Figure 20-3. System Clock Signals
20.2.3 Clocks in Stop Mode and Wait Mode
Upon exit from stop mode by an interrupt or reset, the SIM allows CGMXCLK to
clock the SIM counter. The CPU and peripheral clocks do not become active until
after the stop delay timeout. This timeout is selectable as 4096 or 32 CGMXCLK
cycles. See 20.6.2 Stop Mode.
In wait mode, the CPU clocks are inactive. The SIM also produces two sets of
clocks for other modules. Refer to the wait mode subsection of each module to see
if the module is active or inactive in wait mode. Some modules can be programmed
to be active in wait mode.
20.3 Reset and System Initialization
The MCU has these reset sources:
•
Power-on reset module (POR)
•
External reset pin (RST)
•
Computer operating properly module (COP)
•
Low-voltage inhibit module (LVI)
•
Illegal opcode
•
Illegal address
•
Forced monitor mode entry reset (MODRST)
Data Sheet
258
MC68HC908GZ8
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
System Integration Module (SIM)
Reset and System Initialization
All of these resets produce the vector $FFFE:$FFFF ($FEFE:$FEFF in monitor
mode) and assert the internal reset signal (IRST). IRST causes all registers to be
returned to their default values and all modules to be returned to their reset states.
An internal reset clears the SIM counter (see 20.4 SIM Counter), but an external
reset does not. Each of the resets sets a corresponding bit in the SIM reset status
register (SRSR). See 20.7 SIM Registers.
Freescale Semiconductor, Inc...
20.3.1 External Pin Reset
The RST pin circuit includes an internal pullup device. Pulling the asynchronous
RST pin low halts all processing. The PIN bit of the SIM reset status register
(SRSR) is set as long as RST is held low for a minimum of 67 CGMXCLK cycles,
assuming that neither the POR nor the LVI was the source of the reset. See Table
20-2 for details. Figure 20-4 shows the relative timing.
Table 20-2. PIN Bit Set Timing
Reset Type
Number of Cycles Required to Set PIN
POR/LVI
4163 (4096 + 64 + 3)
All others
67 (64 + 3)
CGMOUT
RST
IAB
VECT H VECT L
PC
Figure 20-4. External Reset Timing
20.3.2 Active Resets from Internal Sources
All internal reset sources actively pull the RST pin low for 32 CGMXCLK cycles to
allow resetting of external peripherals. The internal reset continues to be asserted
for an additional 32 cycles at which point the reset vector will be fetched. See
Figure 20-5. An internal reset can be caused by an illegal address, illegal opcode,
COP timeout, LVI, or POR. See Figure 20-6.
NOTE:
For LVI or POR resets, the SIM cycles through 4096 + 32 CGMXCLK cycles during
which the SIM forces the RST pin low. The internal reset signal then follows the
sequence from the falling edge of RST shown in Figure 20-5.
The COP reset is asynchronous to the bus clock.
MC68HC908GZ8
MOTOROLA
Data Sheet
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
259
Freescale Semiconductor, Inc.
System Integration Module (SIM)
RST
RST PULLED LOW BY MCU
32 CYCLES
32 CYCLES
CGMXCLK
IAB
VECTOR HIGH
Freescale Semiconductor, Inc...
Figure 20-5. Internal Reset Timing
ILLEGAL ADDRESS RST
ILLEGAL OPCODE RST
COPRST
LVI
POR
MODRST
INTERNAL RESET
Figure 20-6. Sources of Internal Reset
The active reset feature allows the part to issue a reset to peripherals and other
chips within a system built around the MCU.
20.3.2.1 Power-On Reset
When power is first applied to the MCU, the power-on reset module (POR)
generates a pulse to indicate that power-on has occurred. The external reset pin
(RST) is held low while the SIM counter counts out 4096 + 32 CGMXCLK cycles.
Thirty-two CGMXCLK cycles later, the CPU and memories are released from reset
to allow the reset vector sequence to occur.
At power-on, these events occur:
•
A POR pulse is generated.
•
The internal reset signal is asserted.
•
The SIM enables CGMOUT.
•
Internal clocks to the CPU and modules are held inactive for 4096
CGMXCLK cycles to allow stabilization of the oscillator.
•
The RST pin is driven low during the oscillator stabilization time.
•
The POR bit of the SIM reset status register (SRSR) is set and all other bits
in the register are cleared.
Data Sheet
260
MC68HC908GZ8
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
System Integration Module (SIM)
Reset and System Initialization
OSC1
PORRST
4096
CYCLES
32
CYCLES
CGMXCLK
Freescale Semiconductor, Inc...
CGMOUT
RST
$FFFE
IAB
$FFFF
Figure 20-7. POR Recovery
20.3.2.2 Computer Operating Properly (COP) Reset
An input to the SIM is reserved for the COP reset signal. The overflow of the COP
counter causes an internal reset and sets the COP bit in the SIM reset status
register (SRSR). The SIM actively pulls down the RST pin for all internal reset
sources.
The COP module is disabled if the RST pin or the IRQ pin is held at VTST while the
MCU is in monitor mode. The COP module can be disabled only through
combinational logic conditioned with the high voltage signal on the RST or the IRQ
pin. This prevents the COP from becoming disabled as a result of external noise.
During a break state, VTST on the RST pin disables the COP module.
20.3.2.3 Illegal Opcode Reset
The SIM decodes signals from the CPU to detect illegal instructions. An illegal
instruction sets the ILOP bit in the SIM reset status register (SRSR) and causes a
reset.
If the stop enable bit, STOP, in the mask option register is logic 0, the SIM treats
the STOP instruction as an illegal opcode and causes an illegal opcode reset. The
SIM actively pulls down the RST pin for all internal reset sources.
20.3.2.4 Illegal Address Reset
An opcode fetch from an unmapped address generates an illegal address reset.
The SIM verifies that the CPU is fetching an opcode prior to asserting the ILAD bit
in the SIM reset status register (SRSR) and resetting the MCU. A data fetch from
an unmapped address does not generate a reset. The SIM actively pulls down the
RST pin for all internal reset sources.
MC68HC908GZ8
MOTOROLA
Data Sheet
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
261
Freescale Semiconductor, Inc.
System Integration Module (SIM)
20.3.2.5 Low-Voltage Inhibit (LVI) Reset
The low-voltage inhibit module (LVI) asserts its output to the SIM when the VDD
voltage falls to the LVITRIPF voltage. The LVI bit in the SIM reset status register
(SRSR) is set, and the external reset pin (RST) is held low while the SIM counter
counts out 4096 + 32 CGMXCLK cycles.
Thirty-two CGMXCLK cycles later, the CPU is released from reset to allow the
reset vector sequence to occur. The SIM actively pulls down the RST pin for all
internal reset sources.
Freescale Semiconductor, Inc...
20.3.2.6 Monitor Mode Entry Module Reset (MODRST)
The monitor mode entry module reset (MODRST) asserts its output to the SIM
when monitor mode is entered in the condition where the reset vectors are erased
($FF) (see 15.3.1 Normal Monitor Mode). When MODRST gets asserted, an
internal reset occurs. The SIM actively pulls down the RST pin for all internal reset
sources.
20.4 SIM Counter
The SIM counter is used by the power-on reset module (POR) and in stop mode
recovery to allow the oscillator time to stabilize before enabling the internal bus
(IBUS) clocks. The SIM counter is 13 bits long.
20.4.1 SIM Counter During Power-On Reset
The power-on reset module (POR) detects power applied to the MCU. At
power-on, the POR circuit asserts the signal PORRST. Once the SIM is initialized,
it enables the clock generation module (CGM) to drive the bus clock state machine.
20.4.2 SIM Counter During Stop Mode Recovery
The SIM counter also is used for stop mode recovery. The STOP instruction clears
the SIM counter. After an interrupt, break, or reset, the SIM senses the state of the
short stop recovery bit, SSREC, in the mask option register. If the SSREC bit is a
logic 1, then the stop recovery is reduced from the normal delay of 4096 CGMXCLK
cycles down to 32 CGMXCLK cycles. This is ideal for applications using canned
oscillators that do not require long startup times from stop mode. External crystal
applications should use the full stop recovery time, that is, with SSREC cleared.
20.4.3 SIM Counter and Reset States
External reset has no effect on the SIM counter. See 20.6.2 Stop Mode for details.
The SIM counter is free-running after all reset states. See 20.3.2 Active Resets
from Internal Sources for counter control and internal reset recovery sequences.
Data Sheet
262
MC68HC908GZ8
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
System Integration Module (SIM)
Exception Control
20.5 Exception Control
Normal, sequential program execution can be changed in three different ways:
•
Interrupts:
– Maskable hardware CPU interrupts
– Non-maskable software interrupt instruction (SWI)
•
Reset
•
Break interrupts
Freescale Semiconductor, Inc...
20.5.1 Interrupts
At the beginning of an interrupt, the CPU saves the CPU register contents on the
stack and sets the interrupt mask (I bit) to prevent additional interrupts. At the end
of an interrupt, the RTI instruction recovers the CPU register contents from the
stack so that normal processing can resume. Figure 20-8 shows interrupt entry
timing. Figure 20-9 shows interrupt recovery timing.
MODULE
INTERRUPT
I BIT
IAB
IDB
DUMMY
SP
DUMMY
SP – 1
SP – 2
PC – 1[7:0] PC – 1[15:8]
SP – 3
X
SP – 4
A
VECT H
CCR
VECT L
V DATA H
START ADDR
V DATA L
OPCODE
R/W
Figure 20-8. Interrupt Entry Timing
MODULE
INTERRUPT
I BIT
IAB
IDB
SP – 4
SP – 3
CCR
SP – 2
A
SP – 1
X
SP
PC
PC + 1
PC – 1 [7:0] PC – 1 [15:8] OPCODE
OPERAND
R/W
Figure 20-9. Interrupt Recovery Timing
MC68HC908GZ8
MOTOROLA
Data Sheet
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
263
Freescale Semiconductor, Inc.
System Integration Module (SIM)
Interrupts are latched, and arbitration is performed in the SIM at the start of
interrupt processing. The arbitration result is a constant that the CPU uses to
determine which vector to fetch. Once an interrupt is latched by the SIM, no other
interrupt can take precedence, regardless of priority, until the latched interrupt is
serviced (or the I bit is cleared). See Figure 20-10.
FROM RESET
Freescale Semiconductor, Inc...
BREAK
I BIT
SET?
INTERRUPT?
YES
NO
YES
I BIT SET?
NO
IRQ
INTERRUPT?
YES
NO
AS MANY INTERRUPTS
AS EXIST ON CHIP
STACK CPU REGISTERS
SET I BIT
LOAD PC WITH INTERRUPT VECTOR
FETCH NEXT
INSTRUCTION
SWI
INSTRUCTION?
YES
NO
RTI
INSTRUCTION?
YES
UNSTACK CPU REGISTERS
NO
EXECUTE INSTRUCTION
Figure 20-10. Interrupt Processing
Data Sheet
264
MC68HC908GZ8
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
System Integration Module (SIM)
Exception Control
20.5.1.1 Hardware Interrupts
A hardware interrupt does not stop the current instruction. Processing of a
hardware interrupt begins after completion of the current instruction. When the
current instruction is complete, the SIM checks all pending hardware interrupts. If
interrupts are not masked (I bit clear in the condition code register) and if the
corresponding interrupt enable bit is set, the SIM proceeds with interrupt
processing; otherwise, the next instruction is fetched and executed.
Freescale Semiconductor, Inc...
If more than one interrupt is pending at the end of an instruction execution, the
highest priority interrupt is serviced first. Figure 20-11 demonstrates what happens
when two interrupts are pending. If an interrupt is pending upon exit from the
original interrupt service routine, the pending interrupt is serviced before the LDA
instruction is executed.
CLI
BACKGROUND
ROUTINE
LDA #$FF
INT1
PSHH
INT1 INTERRUPT SERVICE ROUTINE
PULH
RTI
INT2
PSHH
INT2 INTERRUPT SERVICE ROUTINE
PULH
RTI
Figure 20-11. Interrupt Recognition Example
The LDA opcode is prefetched by both the INT1 and INT2 RTI instructions.
However, in the case of the INT1 RTI prefetch, this is a redundant operation.
NOTE:
To maintain compatibility with the M6805 Family, the H register is not pushed on
the stack during interrupt entry. If the interrupt service routine modifies the H
register or uses the indexed addressing mode, software should save the H register
and then restore it prior to exiting the routine.
MC68HC908GZ8
MOTOROLA
Data Sheet
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
265
Freescale Semiconductor, Inc.
System Integration Module (SIM)
20.5.1.2 SWI Instruction
The SWI instruction is a non-maskable instruction that causes an interrupt
regardless of the state of the interrupt mask (I bit) in the condition code register.
NOTE:
A software interrupt pushes PC onto the stack. A software interrupt does not push
PC – 1, as a hardware interrupt does.
20.5.1.3 Interrupt Status Registers
Freescale Semiconductor, Inc...
The flags in the interrupt status registers identify maskable interrupt sources. Table
20-3 summarizes the interrupt sources and the interrupt status register flags that
they set. The interrupt status registers can be useful for debugging.
Table 20-3. Interrupt Sources
Priority
Highest
Lowest
Interrupt Source
Interrupt Status Register Flag
Reset
—
SWI instruction
—
IRQ pin
I1
ICG clock monitor
I2
TIM1 channel 0
I3
TIM1 channel 1
I4
TIM1 overflow
I5
TIM2 channel 0
I6
TIM2 channel 1
I7
TIM2 overflow
I8
SPI receiver full
I9
SPI transmitter empty
I10
SCI receive error
I11
SCI receive
I12
SCI transmit
I13
Keyboard
I14
ADC conversion complete
I15
Timebase module
I16
MSCAN08 wakeup
I17
MSCAN08 error
I18
MSCAN08 receive
I19
MSCAN08 transmit
I20
Data Sheet
266
MC68HC908GZ8
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
System Integration Module (SIM)
Exception Control
Interrupt Status
Register 1
Address:
$FE04
Bit 7
6
5
4
3
2
1
Bit 0
Read:
I6
I5
I4
I3
I2
I1
0
0
Write:
R
R
R
R
R
R
R
R
0
0
0
0
0
0
0
0
R
= Reserved
Reset:
Freescale Semiconductor, Inc...
Figure 20-12. Interrupt Status Register 1 (INT1)
I6–I1 — Interrupt Flags 1–6
These flags indicate the presence of interrupt requests from the sources shown
in Table 20-3.
1 = Interrupt request present
0 = No interrupt request present
Bit 0 and Bit 1 — Always read 0
Interrupt Status
Register 2
Address:
$FE05
Bit 7
6
5
4
3
2
1
Bit 0
Read:
I14
I13
I12
I11
I10
I9
I8
I7
Write:
R
R
R
R
R
R
R
R
Reset:
0
0
0
0
0
0
0
0
R
= Reserved
Figure 20-13. Interrupt Status Register 2 (INT2)
I14–I7 — Interrupt Flags 14–7
These flags indicate the presence of interrupt requests from the sources shown
in Table 20-3.
1 = Interrupt request present
0 = No interrupt request present
Interrupt Status
Register 3
Address:
$FE06
Bit 7
6
5
4
3
2
1
Bit 0
Read:
0
0
I20
I19
I18
I17
I16
I15
Write:
R
R
R
R
R
R
R
R
Reset:
0
0
0
0
0
0
0
0
R
= Reserved
Figure 20-14. Interrupt Status Register 3 (INT3)
Bits 7–6 — Always read 0
I20–I15 — Interrupt Flags 20–15
These flags indicate the presence of an interrupt request from the source shown
in Table 20-3.
1 = Interrupt request present
0 = No interrupt request present
MC68HC908GZ8
MOTOROLA
Data Sheet
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
267
Freescale Semiconductor, Inc.
System Integration Module (SIM)
20.5.2 Reset
All reset sources always have equal and highest priority and cannot be arbitrated.
20.5.3 Break Interrupts
Freescale Semiconductor, Inc...
The break module can stop normal program flow at a software-programmable
break point by asserting its break interrupt output (see Section 23. Timer
Interface Module (TIM)). The SIM puts the CPU into the break state by forcing it
to the SWI vector location. Refer to the break interrupt subsection of each module
to see how each module is affected by the break state.
20.5.4 Status Flag Protection in Break Mode
The SIM controls whether status flags contained in other modules can be cleared
during break mode. The user can select whether flags are protected from being
cleared by properly initializing the break clear flag enable bit (BCFE) in the SIM
break flag control register (SBFCR).
Protecting flags in break mode ensures that set flags will not be cleared while in
break mode. This protection allows registers to be freely read and written during
break mode without losing status flag information.
Setting the BCFE bit enables the clearing mechanisms. Once cleared in break
mode, a flag remains cleared even when break mode is exited. Status flags with a
2-step clearing mechanism — for example, a read of one register followed by the
read or write of another — are protected, even when the first step is accomplished
prior to entering break mode. Upon leaving break mode, execution of the second
step will clear the flag as normal.
20.6 Low-Power Modes
Executing the WAIT or STOP instruction puts the MCU in a low
power-consumption mode for standby situations. The SIM holds the CPU in a
non-clocked state. The operation of each of these modes is described in the
following subsections. Both STOP and WAIT clear the interrupt mask (I) in the
condition code register, allowing interrupts to occur.
20.6.1 Wait Mode
In wait mode, the CPU clocks are inactive while the peripheral clocks continue to
run. Figure 20-15 shows the timing for wait mode entry.
A module that is active during wait mode can wakeup the CPU with an interrupt if
the interrupt is enabled. Stacking for the interrupt begins one cycle after the WAIT
instruction during which the interrupt occurred. In wait mode, the CPU clocks are
inactive. Refer to the wait mode subsection of each module to see if the module is
Data Sheet
268
MC68HC908GZ8
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
System Integration Module (SIM)
Low-Power Modes
active or inactive in wait mode. Some modules can be programmed to be active in
wait mode.
Wait mode also can be exited by a reset (or break in emulation mode). A break
interrupt during wait mode sets the SIM break stop/wait bit, SBSW, in the SIM
break status register (SBSR). If the COP disable bit, COPD, in the mask option
register is logic 0, then the computer operating properly module (COP) is enabled
and remains active in wait mode.
IAB
WAIT ADDR
Freescale Semiconductor, Inc...
IDB
WAIT ADDR + 1
PREVIOUS DATA
SAME
SAME
NEXT OPCODE
SAME
SAME
R/W
Note:
Previous data can be operand data or the WAIT opcode, depending on the
last instruction.
Figure 20-15. Wait Mode Entry Timing
Figure 20-16 and Figure 20-17 show the timing for WAIT recovery.
IAB
$6E0B
IDB
$A6
$A6
$6E0C
$A6
$00FF
$01
$00FE
$0B
$00FD
$00FC
$6E
EXITSTOPWAIT
Note: EXITSTOPWAIT = RST pin or CPU interrupt
Figure 20-16. Wait Recovery from Interrupt
32
CYCLES
IAB
IDB
32
CYCLES
$6E0B
$A6
$A6
RSTVCTH
RST VCTL
$A6
RST
CGMXCLK
Figure 20-17. Wait Recovery from Internal Reset
MC68HC908GZ8
MOTOROLA
Data Sheet
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
269
Freescale Semiconductor, Inc.
System Integration Module (SIM)
20.6.2 Stop Mode
In stop mode, the SIM counter is reset and the system clocks are disabled. An
interrupt request from a module can cause an exit from stop mode. Stacking for
interrupts begins after the selected stop recovery time has elapsed. Reset or break
also causes an exit from stop mode.
Freescale Semiconductor, Inc...
The SIM disables the clock generator module outputs (CGMOUT and CGMXCLK)
in stop mode, stopping the CPU and peripherals. Stop recovery time is selectable
using the SSREC bit in the mask option register (MOR). If SSREC is set, stop
recovery is reduced from the normal delay of 4096 CGMXCLK cycles down to 32.
This is ideal for applications using canned oscillators that do not require long
startup times from stop mode.
NOTE:
External crystal applications should use the full stop recovery time by clearing the
SSREC bit.
The SIM counter is held in reset from the execution of the STOP instruction until
the beginning of stop recovery. It is then used to time the recovery period. Figure
20-18 shows stop mode entry timing. Figure 20-19 shows stop mode recovery time
from interrupt.
NOTE:
To minimize stop current, all pins configured as inputs should be driven to a logic 1
or logic 0.
CPUSTOP
IAB
IDB
STOP ADDR + 1
STOP ADDR
PREVIOUS DATA
SAME
NEXT OPCODE
SAME
SAME
SAME
R/W
Note: Previous data can be operand data or the STOP opcode, depending
on the last instruction.
Figure 20-18. Stop Mode Entry Timing
STOP RECOVERY PERIOD
CGMXCLK
INT/BREAK
IAB
STOP +1
STOP + 2
STOP + 2
SP
SP – 1
SP – 2
SP – 3
Figure 20-19. Stop Mode Recovery from Interrupt
Data Sheet
270
MC68HC908GZ8
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
System Integration Module (SIM)
SIM Registers
20.7 SIM Registers
The SIM has three memory-mapped registers. Table 20-4 shows the mapping of
these registers.
Freescale Semiconductor, Inc...
Table 20-4. SIM Registers
Address
Register
Access Mode
$FE00
SBSR
User
$FE01
SRSR
User
$FE03
SBFCR
User
20.7.1 Break Status Register
The break status register (BSR) contains a flag to indicate that a break caused an
exit from wait mode. This register is only used in emulation mode.
Address:
$FE00
Bit 7
Read:
Write:
Reset:
6
5
4
3
2
R
R
R
R
R
R
0
0
0
0
0
0
R
= Reserved
1
SBSW
Note(1)
0
Bit 0
R
0
1. Writing a logic 0 clears SBSW.
Figure 20-20. Break Status Register (BSR)
SBSW — SIM Break Stop/Wait
SBSW can be read within the break state SWI routine. The user can modify the
return address on the stack by subtracting one from it.
1 = Wait mode was exited by break interrupt.
0 = Wait mode was not exited by break interrupt.
MC68HC908GZ8
MOTOROLA
Data Sheet
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
271
Freescale Semiconductor, Inc.
System Integration Module (SIM)
20.7.2 SIM Reset Status Register
This register contains six flags that show the source of the last reset provided all
previous reset status bits have been cleared. Clear the SIM reset status register by
reading it. A power-on reset sets the POR bit and clears all other bits in the register.
Address:
Read:
$FE01
Bit 7
6
5
4
3
2
1
Bit 0
POR
PIN
COP
ILOP
ILAD
MODRST
LVI
0
0
0
0
0
0
0
0
Write:
Reset:
1
Freescale Semiconductor, Inc...
= Unimplemented
Figure 20-21. SIM Reset Status Register (SRSR)
POR — Power-On Reset Bit
1 = Last reset caused by POR circuit
0 = Read of SRSR
PIN — External Reset Bit
1 = Last reset caused by external reset pin (RST)
0 = POR or read of SRSR
COP — Computer Operating Properly Reset Bit
1 = Last reset caused by COP counter
0 = POR or read of SRSR
ILOP — Illegal Opcode Reset Bit
1 = Last reset caused by an illegal opcode
0 = POR or read of SRSR
ILAD — Illegal Address Reset Bit (opcode fetches only)
1 = Last reset caused by an opcode fetch from an illegal address
0 = POR or read of SRSR
MODRST — Monitor Mode Entry Module Reset Bit
1 = Last reset caused by monitor mode entry when vector locations $FFFE
and $FFFF are $FF after POR while IRQ = VDD
0 = POR or read of SRSR
LVI — Low-Voltage Inhibit Reset Bit
1 = Last reset caused by the LVI circuit
0 = POR or read of SRSR
Data Sheet
272
MC68HC908GZ8
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
System Integration Module (SIM)
SIM Registers
20.7.3 Break Flag Control Register
The SIM break control register contains a bit that enables software to clear status
bits while the MCU is in a break state.
Address:
Read:
Write:
Reset:
$FE03
Bit 7
6
5
4
3
2
1
Bit 0
BCFE
R
R
R
R
R
R
R
0
Freescale Semiconductor, Inc...
R
= Reserved
Figure 20-22. Break Flag Control Register (BFCR)
BCFE — Break Clear Flag Enable Bit
This read/write bit enables software to clear status bits by accessing status
registers while the MCU is in a break state. To clear status bits during the break
state, the BCFE bit must be set.
1 = Status bits clearable during break
0 = Status bits not clearable during break
MC68HC908GZ8
MOTOROLA
Data Sheet
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
273
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
System Integration Module (SIM)
Data Sheet
274
MC68HC908GZ8
System Integration Module (SIM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 21. Serial Peripheral Interface (SPI) Module
Freescale Semiconductor, Inc...
21.1 Introduction
This section describes the serial peripheral interface (SPI) module, which allows
full-duplex, synchronous, serial communications with peripheral devices.
21.2 Features
Features of the SPI module include:
•
Full-duplex operation
•
Master and slave modes
•
Double-buffered operation with separate transmit and receive registers
•
Four master mode frequencies (maximum = bus frequency ÷ 2)
•
Maximum slave mode frequency = bus frequency
•
Serial clock with programmable polarity and phase
•
Two separately enabled interrupts:
– SPRF (SPI receiver full)
– SPTE (SPI transmitter empty)
•
Mode fault error flag with CPU interrupt capability
•
Overflow error flag with CPU interrupt capability
•
Programmable wired-OR mode
•
I2C (inter-integrated circuit) compatibility
•
I/O (input/output) port bit(s) software configurable with pullup device(s) if
configured as input port bit(s)
MC68HC908GZ8
MOTOROLA
Data Sheet
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
275
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
21.3 Pin Name Conventions
The text that follows describes the SPI. The SPI I/O pin names are SS (slave
select), SPSCK (SPI serial clock), CGND (clock ground), MOSI (master out slave
in), and MISO (master in/slave out). The SPI shares four I/O pins with four parallel
I/O ports.
The full names of the SPI I/O pins are shown in Table 21-1. The generic pin names
appear in the text that follows.
Freescale Semiconductor, Inc...
Table 21-1. Pin Name Conventions
SPI Generic
Pin Names:
Full SPI
Pin Names:
SPI
MISO
MOSI
SS
SPSCK
CGND
PTD1/MISO
PTD2/MOSI
PTD0/SS
PTD3/SPSCK
VSS
21.4 Functional Description
Figure 21-1 summarizes the SPI I/O registers and Figure 21-2 shows the structure
of the SPI module.
The SPI module allows full-duplex, synchronous, serial communication between
the MCU and peripheral devices, including other MCUs. Software can poll the SPI
status flags or SPI operation can be interrupt driven.
If a port bit is configured for input, then an internal pullup device may be enabled
for that port bit. See 17.4.3 Port C Input Pullup Enable Register.
The following paragraphs describe the operation of the SPI module.
Addr.
Register Name
Read:
SPI Control Register (SPCR)
Write:
$0010
See page 293.
Reset:
SPI Status and Control Reg- Read:
$0011
ister (SPSCR) Write:
See page 295. Reset:
$0012
SPI Data Register Read:
(SPDR) Write:
See page 297. Reset:
Bit 7
6
5
4
3
2
1
Bit 0
SPRIE
R
SPMSTR
CPOL
CPHA
SPWOM
SPE
SPTIE
0
0
1
0
1
0
0
0
OVRF
MODF
SPTE
MODFEN
SPR1
SPR0
SPRF
ERRIE
0
0
0
0
1
0
0
0
R7
R6
R5
R4
R3
R2
R1
R0
T7
T6
T5
T4
T3
T2
T1
T0
Unaffected by reset
R
= Reserved
= Unimplemented
Figure 21-1. SPI I/O Register Summary
Data Sheet
276
MC68HC908GZ8
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
Functional Description
INTERNAL BUS
TRANSMIT DATA REGISTER
CGMOUT ÷ 2
FROM SIM
SHIFT REGISTER
7
6
5
4
3
2
1
MISO
0
÷2
Freescale Semiconductor, Inc...
CLOCK
DIVIDER
MOSI
÷8
RECEIVE DATA REGISTER
÷ 32
PIN
CONTROL
LOGIC
÷ 128
SPMSTR
SPE
CLOCK
SELECT
SPR1
SPSCK
M
CLOCK
LOGIC
S
SS
SPR0
SPMSTR
RESERVED
MODFEN
TRANSMITTER CPU INTERRUPT REQUEST
RESERVED
CPHA
CPOL
SPWOM
ERRIE
SPI
CONTROL
SPTIE
SPRIE
RECEIVER/ERROR CPU INTERRUPT REQUEST
DMAS
SPE
SPRF
SPTE
OVRF
MODF
Figure 21-2. SPI Module Block Diagram
MC68HC908GZ8
MOTOROLA
Data Sheet
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
277
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
21.4.1 Master Mode
The SPI operates in master mode when the SPI master bit, SPMSTR, is set.
NOTE:
Configure the SPI modules as master or slave before enabling them. Enable the
master SPI before enabling the slave SPI. Disable the slave SPI before disabling
the master SPI. See 21.13.1 SPI Control Register.
Freescale Semiconductor, Inc...
Only a master SPI module can initiate transmissions. Software begins the
transmission from a master SPI module by writing to the transmit data register. If
the shift register is empty, the byte immediately transfers to the shift register,
setting the SPI transmitter empty bit, SPTE. The byte begins shifting out on the
MOSI pin under the control of the serial clock. See Figure 21-3.
MASTER MCU
SHIFT REGISTER
SLAVE MCU
MISO
MISO
MOSI
MOSI
SPSCK
BAUD RATE
GENERATOR
SS
SHIFT REGISTER
SPSCK
VDD
SS
Figure 21-3. Full-Duplex Master-Slave Connections
The SPR1 and SPR0 bits control the baud rate generator and determine the speed
of the shift register. (See 21.13.2 SPI Status and Control Register.) Through the
SPSCK pin, the baud rate generator of the master also controls the shift register of
the slave peripheral.
As the byte shifts out on the MOSI pin of the master, another byte shifts in from the
slave on the master’s MISO pin. The transmission ends when the receiver full bit,
SPRF, becomes set. At the same time that SPRF becomes set, the byte from the
slave transfers to the receive data register. In normal operation, SPRF signals the
end of a transmission. Software clears SPRF by reading the SPI status and control
register with SPRF set and then reading the SPI data register. Writing to the SPI
data register clears the SPTE bit.
21.4.2 Slave Mode
The SPI operates in slave mode when the SPMSTR bit is clear. In slave mode, the
SPSCK pin is the input for the serial clock from the master MCU. Before a data
transmission occurs, the SS pin of the slave SPI must be at logic 0. SS must remain
low until the transmission is complete. See 21.7.2 Mode Fault Error.
In a slave SPI module, data enters the shift register under the control of the serial
clock from the master SPI module. After a byte enters the shift register of a slave
Data Sheet
278
MC68HC908GZ8
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
Transmission Formats
SPI, it transfers to the receive data register, and the SPRF bit is set. To prevent an
overflow condition, slave software then must read the receive data register before
another full byte enters the shift register.
Freescale Semiconductor, Inc...
The maximum frequency of the SPSCK for an SPI configured as a slave is the bus
clock speed (which is twice as fast as the fastest master SPSCK clock that can be
generated). The frequency of the SPSCK for an SPI configured as a slave does not
have to correspond to any SPI baud rate. The baud rate only controls the speed of
the SPSCK generated by an SPI configured as a master. Therefore, the frequency
of the SPSCK for an SPI configured as a slave can be any frequency less than or
equal to the bus speed.
When the master SPI starts a transmission, the data in the slave shift register
begins shifting out on the MISO pin. The slave can load its shift register with a new
byte for the next transmission by writing to its transmit data register. The slave must
write to its transmit data register at least one bus cycle before the master starts the
next transmission. Otherwise, the byte already in the slave shift register shifts out
on the MISO pin. Data written to the slave shift register during a transmission
remains in a buffer until the end of the transmission.
When the clock phase bit (CPHA) is set, the first edge of SPSCK starts a
transmission. When CPHA is clear, the falling edge of SS starts a transmission.
See 21.5 Transmission Formats.
NOTE:
SPSCK must be in the proper idle state before the slave is enabled to prevent
SPSCK from appearing as a clock edge.
21.5 Transmission Formats
During an SPI transmission, data is simultaneously transmitted (shifted out serially)
and received (shifted in serially). A serial clock synchronizes shifting and sampling
on the two serial data lines. A slave select line allows selection of an individual
slave SPI device; slave devices that are not selected do not interfere with SPI bus
activities. On a master SPI device, the slave select line can optionally be used to
indicate multiple-master bus contention.
21.5.1 Clock Phase and Polarity Controls
Software can select any of four combinations of serial clock (SPSCK) phase and
polarity using two bits in the SPI control register (SPCR). The clock polarity is
specified by the CPOL control bit, which selects an active high or low clock and has
no significant effect on the transmission format.
The clock phase (CPHA) control bit selects one of two fundamentally different
transmission formats. The clock phase and polarity should be identical for the
master SPI device and the communicating slave device. In some cases, the phase
and polarity are changed between transmissions to allow a master device to
communicate with peripheral slaves having different requirements.
MC68HC908GZ8
MOTOROLA
Data Sheet
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
279
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
NOTE:
Before writing to the CPOL bit or the CPHA bit, disable the SPI by clearing the SPI
enable bit (SPE).
21.5.2 Transmission Format When CPHA = 0
Figure 21-4 shows an SPI transmission in which CPHA is logic 0. The figure should
not be used as a replacement for data sheet parametric information.
Freescale Semiconductor, Inc...
Two waveforms are shown for SPSCK: one for CPOL = 0 and another for
CPOL = 1. The diagram may be interpreted as a master or slave timing diagram
since the serial clock (SPSCK), master in/slave out (MISO), and master out/slave
in (MOSI) pins are directly connected between the master and the slave. The MISO
signal is the output from the slave, and the MOSI signal is the output from the
master. The SS line is the slave select input to the slave. The slave SPI drives its
MISO output only when its slave select input (SS) is at logic 0, so that only the
selected slave drives to the master. The SS pin of the master is not shown but is
assumed to be inactive. The SS pin of the master must be high or must be
reconfigured as general-purpose I/O not affecting the SPI. (See 21.7.2 Mode Fault
Error.) When CPHA = 0, the first SPSCK edge is the MSB capture strobe.
Therefore, the slave must begin driving its data before the first SPSCK edge, and
a falling edge on the SS pin is used to start the slave data transmission. The slave’s
SS pin must be toggled back to high and then low again between each byte
transmitted as shown in Figure 21-5.
SPSCK CYCLE #
FOR REFERENCE
1
2
3
4
5
6
7
8
MSB
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
LSB
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
LSB
SPSCK; CPOL = 0
SPSCK; CPOL =1
MOSI
FROM MASTER
MISO
FROM SLAVE
MSB
SS; TO SLAVE
CAPTURE STROBE
Figure 21-4. Transmission Format (CPHA = 0)
MISO/MOSI
BYTE 1
BYTE 2
BYTE 3
MASTER SS
SLAVE SS
CPHA = 0
SLAVE SS
CPHA = 1
Figure 21-5. CPHA/SS Timing
Data Sheet
280
MC68HC908GZ8
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
Transmission Formats
When CPHA = 0 for a slave, the falling edge of SS indicates the beginning of the
transmission. This causes the SPI to leave its idle state and begin driving the MISO
pin with the MSB of its data. Once the transmission begins, no new data is allowed
into the shift register from the transmit data register. Therefore, the SPI data
register of the slave must be loaded with transmit data before the falling edge of
SS. Any data written after the falling edge is stored in the transmit data register and
transferred to the shift register after the current transmission.
21.5.3 Transmission Format When CPHA = 1
Freescale Semiconductor, Inc...
Figure 21-6 shows an SPI transmission in which CPHA is logic 1. The figure should
not be used as a replacement for data sheet parametric information. Two
waveforms are shown for SPSCK: one for CPOL = 0 and another for CPOL = 1.
The diagram may be interpreted as a master or slave timing diagram since the
serial clock (SPSCK), master in/slave out (MISO), and master out/slave in (MOSI)
pins are directly connected between the master and the slave. The MISO signal is
the output from the slave, and the MOSI signal is the output from the master. The
SS line is the slave select input to the slave. The slave SPI drives its MISO output
only when its slave select input (SS) is at logic 0, so that only the selected slave
drives to the master. The SS pin of the master is not shown but is assumed to be
inactive. The SS pin of the master must be high or must be reconfigured as
general-purpose I/O not affecting the SPI. (See 21.7.2 Mode Fault Error.) When
CPHA = 1, the master begins driving its MOSI pin on the first SPSCK edge.
Therefore, the slave uses the first SPSCK edge as a start transmission signal. The
SS pin can remain low between transmissions. This format may be preferable in
systems having only one master and only one slave driving the MISO data line.
When CPHA = 1 for a slave, the first edge of the SPSCK indicates the beginning
of the transmission. This causes the SPI to leave its idle state and begin driving the
MISO pin with the MSB of its data. Once the transmission begins, no new data is
allowed into the shift register from the transmit data register. Therefore, the SPI
data register of the slave must be loaded with transmit data before the first edge of
SPSCK. Any data written after the first edge is stored in the transmit data register
and transferred to the shift register after the current transmission.
SPSCK CYCLE #
FOR REFERENCE
1
2
3
4
5
6
7
8
MOSI
FROM MASTER
MSB
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
LSB
MISO
FROM SLAVE
MSB
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
SPSCK; CPOL = 0
SPSCK; CPOL =1
LSB
SS; TO SLAVE
CAPTURE STROBE
Figure 21-6. Transmission Format (CPHA = 1)
MC68HC908GZ8
MOTOROLA
Data Sheet
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
281
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
21.5.4 Transmission Initiation Latency
When the SPI is configured as a master (SPMSTR = 1), writing to the SPDR starts
a transmission. CPHA has no effect on the delay to the start of the transmission,
but it does affect the initial state of the SPSCK signal. When CPHA = 0, the SPSCK
signal remains inactive for the first half of the first SPSCK cycle. When CPHA = 1,
the first SPSCK cycle begins with an edge on the SPSCK line from its inactive to
its active level. The SPI clock rate (selected by SPR1:SPR0) affects the delay from
the write to SPDR and the start of the SPI transmission. (See Figure 21-7.)
WRITE
TO SPDR
INITIATION DELAY
Freescale Semiconductor, Inc...
BUS
CLOCK
MOSI
MSB
BIT 6
BIT 5
SPSCK
CPHA = 1
SPSCK
CPHA = 0
SPSCK CYCLE
NUMBER
1
2
3
INITIATION DELAY FROM WRITE SPDR TO TRANSFER BEGIN
WRITE
TO SPDR
BUS
CLOCK
EARLIEST
WRITE
TO SPDR
LATEST
SPSCK = INTERNAL CLOCK ÷ 2;
2 POSSIBLE START POINTS
BUS
CLOCK
EARLIEST
WRITE
TO SPDR
SPSCK = INTERNAL CLOCK ÷ 8;
8 POSSIBLE START POINTS
LATEST
SPSCK = INTERNAL CLOCK ÷ 32;
32 POSSIBLE START POINTS
LATEST
SPSCK = INTERNAL CLOCK ÷ 128;
128 POSSIBLE START POINTS
LATEST
BUS
CLOCK
EARLIEST
WRITE
TO SPDR
BUS
CLOCK
EARLIEST
Figure 21-7. Transmission Start Delay (Master)
Data Sheet
282
MC68HC908GZ8
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
Queuing Transmission Data
The internal SPI clock in the master is a free-running derivative of the internal MCU
clock. To conserve power, it is enabled only when both the SPE and SPMSTR bits
are set. SPSCK edges occur halfway through the low time of the internal MCU
clock. Since the SPI clock is free-running, it is uncertain where the write to the
SPDR occurs relative to the slower SPSCK. This uncertainty causes the variation
in the initiation delay shown in Figure 21-7. This delay is no longer than a single
SPI bit time. That is, the maximum delay is two MCU bus cycles for DIV2, eight
MCU bus cycles for DIV8, 32 MCU bus cycles for DIV32, and 128 MCU bus cycles
for DIV128.
Freescale Semiconductor, Inc...
21.6 Queuing Transmission Data
The double-buffered transmit data register allows a data byte to be queued and
transmitted. For an SPI configured as a master, a queued data byte is transmitted
immediately after the previous transmission has completed. The SPI transmitter
empty flag (SPTE) indicates when the transmit data buffer is ready to accept new
data. Write to the transmit data register only when the SPTE bit is high. Figure 21-8
shows the timing associated with doing back-to-back transmissions with the SPI
(SPSCK has CPHA: CPOL = 1:0).
WRITE TO SPDR
SPTE
1
3
2
8
5
10
SPSCK
CPHA:CPOL = 1:0
MOSI
MSB BIT BIT BIT BIT BIT BIT LSB MSB BIT BIT BIT BIT BIT BIT LSB MSB BIT BIT BIT
6 5 4
6 5 4 3 2 1
6 5 4 3 2 1
BYTE 1
BYTE 2
BYTE 3
9
4
SPRF
6
READ SPSCR
11
7
READ SPDR
12
1 CPU WRITES BYTE 1 TO SPDR, CLEARING SPTE BIT.
7 CPU READS SPDR, CLEARING SPRF BIT.
2 BYTE 1 TRANSFERS FROM TRANSMIT DATA
REGISTER TO SHIFT REGISTER, SETTING SPTE BIT.
8 CPU WRITES BYTE 3 TO SPDR, QUEUEING BYTE
3 AND CLEARING SPTE BIT.
9 SECOND INCOMING BYTE TRANSFERS FROM SHIFT
REGISTER TO RECEIVE DATA REGISTER, SETTING
SPRF BIT.
10 BYTE 3 TRANSFERS FROM TRANSMIT DATA
REGISTER TO SHIFT REGISTER, SETTING SPTE BIT.
11 CPU READS SPSCR WITH SPRF BIT SET.
3 CPU WRITES BYTE 2 TO SPDR, QUEUEING BYTE 2
AND CLEARING SPTE BIT.
FIRST INCOMING BYTE TRANSFERS FROM SHIFT
REGISTER TO RECEIVE DATA REGISTER, SETTING
SPRF BIT.
5 BYTE 2 TRANSFERS FROM TRANSMIT DATA
REGISTER TO SHIFT REGISTER, SETTING SPTE BIT.
6 CPU READS SPSCR WITH SPRF BIT SET.
4
12 CPU READS SPDR, CLEARING SPRF BIT.
Figure 21-8. SPRF/SPTE CPU Interrupt Timing
MC68HC908GZ8
MOTOROLA
Data Sheet
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
283
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
The transmit data buffer allows back-to-back transmissions without the slave
precisely timing its writes between transmissions as in a system with a single data
buffer. Also, if no new data is written to the data buffer, the last value contained in
the shift register is the next data word to be transmitted.
Freescale Semiconductor, Inc...
For an idle master or idle slave that has no data loaded into its transmit buffer, the
SPTE is set again no more than two bus cycles after the transmit buffer empties
into the shift register. This allows the user to queue up a 16-bit value to send. For
an already active slave, the load of the shift register cannot occur until the
transmission is completed. This implies that a back-to-back write to the transmit
data register is not possible. The SPTE indicates when the next write can occur.
21.7 Error Conditions
The following flags signal SPI error conditions:
• Overflow (OVRF) — Failing to read the SPI data register before the next full
byte enters the shift register sets the OVRF bit. The new byte does not
transfer to the receive data register, and the unread byte still can be read.
OVRF is in the SPI status and control register.
• Mode fault error (MODF) — The MODF bit indicates that the voltage on the
slave select pin (SS) is inconsistent with the mode of the SPI. MODF is in
the SPI status and control register.
21.7.1 Overflow Error
The overflow flag (OVRF) becomes set if the receive data register still has unread
data from a previous transmission when the capture strobe of bit 1 of the next
transmission occurs. The bit 1 capture strobe occurs in the middle of SPSCK cycle
7 (see Figure 21-4 and Figure 21-6.) If an overflow occurs, all data received after
the overflow and before the OVRF bit is cleared does not transfer to the receive
data register and does not set the SPI receiver full bit (SPRF). The unread data that
transferred to the receive data register before the overflow occurred can still be
read. Therefore, an overflow error always indicates the loss of data. Clear the
overflow flag by reading the SPI status and control register and then reading the
SPI data register.
OVRF generates a receiver/error CPU interrupt request if the error interrupt enable
bit (ERRIE) is also set. The SPRF, MODF, and OVRF interrupts share the same
CPU interrupt vector (see Figure 21-11.) It is not possible to enable MODF or
OVRF individually to generate a receiver/error CPU interrupt request. However,
leaving MODFEN low prevents MODF from being set.
If the CPU SPRF interrupt is enabled and the OVRF interrupt is not, watch for an
overflow condition. Figure 21-9 shows how it is possible to miss an overflow. The
first part of Figure 21-9 shows how it is possible to read the SPSCR and SPDR to
clear the SPRF without problems. However, as illustrated by the second
transmission example, the OVRF bit can be set in between the time that SPSCR
and SPDR are read.
Data Sheet
284
MC68HC908GZ8
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
Error Conditions
BYTE 1
BYTE 2
BYTE 3
BYTE 4
1
4
6
8
SPRF
OVRF
READ
SPSCR
2
Freescale Semiconductor, Inc...
READ
SPDR
5
3
1
BYTE 1 SETS SPRF BIT.
2
CPU READS SPSCR WITH SPRF BIT SET
AND OVRF BIT CLEAR.
CPU READS BYTE 1 IN SPDR,
CLEARING SPRF BIT.
BYTE 2 SETS SPRF BIT.
3
4
7
5
CPU READS SPSCR WITH SPRF BIT SET
AND OVRF BIT CLEAR.
6
BYTE 3 SETS OVRF BIT. BYTE 3 IS LOST.
7
CPU READS BYTE 2 IN SPDR, CLEARING SPRF BIT,
BUT NOT OVRF BIT.
8
BYTE 4 FAILS TO SET SPRF BIT BECAUSE
OVRF BIT IS NOT CLEARED. BYTE 4 IS LOST.
Figure 21-9. Missed Read of Overflow Condition
In this case, an overflow can be missed easily. Since no more SPRF interrupts can
be generated until this OVRF is serviced, it is not obvious that bytes are being lost
as more transmissions are completed. To prevent this, either enable the OVRF
interrupt or do another read of the SPSCR following the read of the SPDR. This
ensures that the OVRF was not set before the SPRF was cleared and that future
transmissions can set the SPRF bit. Figure 21-10 illustrates this process.
Generally, to avoid this second SPSCR read, enable the OVRF to the CPU by
setting the ERRIE bit.
21.7.2 Mode Fault Error
Setting the SPMSTR bit selects master mode and configures the SPSCK and
MOSI pins as outputs and the MISO pin as an input. Clearing SPMSTR selects
slave mode and configures the SPSCK and MOSI pins as inputs and the MISO pin
as an output. The mode fault bit, MODF, becomes set any time the state of the
slave select pin, SS, is inconsistent with the mode selected by SPMSTR.
To prevent SPI pin contention and damage to the MCU, a mode fault error occurs if:
•
The SS pin of a slave SPI goes high during a transmission
•
The SS pin of a master SPI goes low at any time
For the MODF flag to be set, the mode fault error enable bit (MODFEN) must be
set. Clearing the MODFEN bit does not clear the MODF flag but does prevent
MODF from being set again after MODF is cleared.
MC68HC908GZ8
MOTOROLA
Data Sheet
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
285
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
BYTE 1
SPI RECEIVE
COMPLETE
BYTE 2
5
1
BYTE 3
7
BYTE 4
11
SPRF
OVRF
READ
SPSCR
2
Freescale Semiconductor, Inc...
READ
SPDR
4
6
3
1
BYTE 1 SETS SPRF BIT.
2
CPU READS SPSCR WITH SPRF BIT SET
AND OVRF BIT CLEAR.
CPU READS BYTE 1 IN SPDR,
CLEARING SPRF BIT.
3
9
8
12
14
10
13
8
CPU READS BYTE 2 IN SPDR,
CLEARING SPRF BIT.
9
CPU READS SPSCR AGAIN
TO CHECK OVRF BIT.
10 CPU READS BYTE 2 SPDR,
CLEARING OVRF BIT.
4
CPU READS SPSCR AGAIN
TO CHECK OVRF BIT.
11 BYTE 4 SETS SPRF BIT.
5
BYTE 2 SETS SPRF BIT.
12 CPU READS SPSCR.
6
CPU READS SPSCR WITH SPRF BIT SET
AND OVRF BIT CLEAR.
13 CPU READS BYTE 4 IN SPDR,
CLEARING SPRF BIT.
7
BYTE 3 SETS OVRF BIT. BYTE 3 IS LOST.
14 CPU READS SPSCR AGAIN
TO CHECK OVRF BIT.
Figure 21-10. Clearing SPRF When OVRF Interrupt Is Not Enabled
MODF generates a receiver/error CPU interrupt request if the error interrupt enable
bit (ERRIE) is also set. The SPRF, MODF, and OVRF interrupts share the same
CPU interrupt vector. (See Figure 21-11.) It is not possible to enable MODF or
OVRF individually to generate a receiver/error CPU interrupt request. However,
leaving MODFEN low prevents MODF from being set.
In a master SPI with the mode fault enable bit (MODFEN) set, the mode fault flag
(MODF) is set if SS goes to logic 0. A mode fault in a master SPI causes the
following events to occur:
• If ERRIE = 1, the SPI generates an SPI receiver/error CPU interrupt request.
• The SPE bit is cleared.
• The SPTE bit is set.
• The SPI state counter is cleared.
• The data direction register of the shared I/O port regains control of port
drivers.
NOTE:
To prevent bus contention with another master SPI after a mode fault error, clear
all SPI bits of the data direction register of the shared I/O port before enabling the
SPI.
When configured as a slave (SPMSTR = 0), the MODF flag is set if SS goes high
during a transmission. When CPHA = 0, a transmission begins when SS goes low
and ends once the incoming SPSCK goes back to its idle level following the shift
Data Sheet
286
MC68HC908GZ8
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
Interrupts
of the eighth data bit. When CPHA = 1, the transmission begins when the SPSCK
leaves its idle level and SS is already low. The transmission continues until the
SPSCK returns to its idle level following the shift of the last data bit. See 21.5
Transmission Formats.
Freescale Semiconductor, Inc...
NOTE:
Setting the MODF flag does not clear the SPMSTR bit. The SPMSTR bit has no
function when SPE = 0. Reading SPMSTR when MODF = 1 shows the difference
between a MODF occurring when the SPI is a master and when it is a slave.
When CPHA = 0, a MODF occurs if a slave is selected (SS is at logic 0) and later
unselected (SS is at logic 1) even if no SPSCK is sent to that slave. This happens
because SS at logic 0 indicates the start of the transmission (MISO driven out with
the value of MSB) for CPHA = 0. When CPHA = 1, a slave can be selected and
then later unselected with no transmission occurring. Therefore, MODF does not
occur since a transmission was never begun.
In a slave SPI (MSTR = 0), the MODF bit generates an SPI receiver/error CPU
interrupt request if the ERRIE bit is set. The MODF bit does not clear the SPE bit
or reset the SPI in any way. Software can abort the SPI transmission by clearing
the SPE bit of the slave.
NOTE:
A logic 1 voltage on the SS pin of a slave SPI puts the MISO pin in a high
impedance state. Also, the slave SPI ignores all incoming SPSCK clocks, even if it
was already in the middle of a transmission.
To clear the MODF flag, read the SPSCR with the MODF bit set and then write to
the SPCR register. This entire clearing mechanism must occur with no MODF
condition existing or else the flag is not cleared.
21.8 Interrupts
Four SPI status flags can be enabled to generate CPU interrupt requests. See
Table 21-2.
Table 21-2. SPI Interrupts
Flag
Request
SPTE
Transmitter empty
SPI transmitter CPU interrupt request
(DMAS = 0, SPTIE = 1, SPE = 1)
SPRF
Receiver full
SPI receiver CPU interrupt request
(DMAS = 0, SPRIE = 1)
OVRF
Overflow
SPI receiver/error interrupt request
(ERRIE = 1)
MODF
Mode fault
SPI receiver/error interrupt request
(ERRIE = 1)
Reading the SPI status and control register with SPRF set and then reading the
receive data register clears SPRF. The clearing mechanism for the SPTE flag is
always just a write to the transmit data register.
MC68HC908GZ8
MOTOROLA
Data Sheet
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
287
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
The SPI transmitter interrupt enable bit (SPTIE) enables the SPTE flag to generate
transmitter CPU interrupt requests, provided that the SPI is enabled (SPE = 1).
The SPI receiver interrupt enable bit (SPRIE) enables the SPRF bit to generate
receiver CPU interrupt requests, regardless of the state of the SPE bit. See Figure
21-11.
The error interrupt enable bit (ERRIE) enables both the MODF and OVRF bits to
generate a receiver/error CPU interrupt request.
Freescale Semiconductor, Inc...
The mode fault enable bit (MODFEN) can prevent the MODF flag from being set
so that only the OVRF bit is enabled by the ERRIE bit to generate receiver/error
CPU interrupt requests.
NOT AVAILABLE
SPTE
SPTIE
SPE
SPI TRANSMITTER
CPU INTERRUPT REQUEST
DMAS
NOT AVAILABLE
SPRIE
SPRF
SPI RECEIVER/ERROR
CPU INTERRUPT REQUEST
ERRIE
MODF
OVRF
Figure 21-11. SPI Interrupt Request Generation
The following sources in the SPI status and control register can generate CPU
interrupt requests:
•
SPI receiver full bit (SPRF) — The SPRF bit becomes set every time a byte
transfers from the shift register to the receive data register. If the SPI
receiver interrupt enable bit, SPRIE, is also set, SPRF generates an SPI
receiver/error CPU interrupt request.
•
SPI transmitter empty (SPTE) — The SPTE bit becomes set every time a
byte transfers from the transmit data register to the shift register. If the SPI
transmit interrupt enable bit, SPTIE, is also set, SPTE generates an SPTE
CPU interrupt request.
Data Sheet
288
MC68HC908GZ8
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
Resetting the SPI
21.9 Resetting the SPI
Freescale Semiconductor, Inc...
Any system reset completely resets the SPI. Partial resets occur whenever the SPI
enable bit (SPE) is low. Whenever SPE is low, the following occurs:
•
The SPTE flag is set.
•
Any transmission currently in progress is aborted.
•
The shift register is cleared.
•
The SPI state counter is cleared, making it ready for a new complete
transmission.
•
All the SPI port logic is defaulted back to being general-purpose I/O.
These items are reset only by a system reset:
•
All control bits in the SPCR register
•
All control bits in the SPSCR register (MODFEN, ERRIE, SPR1, and SPR0)
•
The status flags SPRF, OVRF, and MODF
By not resetting the control bits when SPE is low, the user can clear SPE between
transmissions without having to set all control bits again when SPE is set back high
for the next transmission.
By not resetting the SPRF, OVRF, and MODF flags, the user can still service these
interrupts after the SPI has been disabled. The user can disable the SPI by writing
0 to the SPE bit. The SPI can also be disabled by a mode fault occurring in an SPI
that was configured as a master with the MODFEN bit set.
21.10 Low-Power Modes
The WAIT and STOP instructions put the MCU in low power-consumption standby
modes.
21.10.1 Wait Mode
The SPI module remains active after the execution of a WAIT instruction. In wait
mode the SPI module registers are not accessible by the CPU. Any enabled CPU
interrupt request from the SPI module can bring the MCU out of wait mode.
If SPI module functions are not required during wait mode, reduce power
consumption by disabling the SPI module before executing the WAIT instruction.
To exit wait mode when an overflow condition occurs, enable the OVRF bit to
generate CPU interrupt requests by setting the error interrupt enable bit (ERRIE).
See 21.8 Interrupts.
MC68HC908GZ8
MOTOROLA
Data Sheet
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
289
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
21.10.2 Stop Mode
The SPI module is inactive after the execution of a STOP instruction. The STOP
instruction does not affect register conditions. SPI operation resumes after an
external interrupt. If stop mode is exited by reset, any transfer in progress is
aborted, and the SPI is reset.
Freescale Semiconductor, Inc...
21.11 SPI During Break Interrupts
The system integration module (SIM) controls whether status bits in other modules
can be cleared during the break state. The BCFE bit in the SIM break flag control
register (SBFCR) enables software to clear status bits during the break state. See
Section 20. System Integration Module (SIM).
To allow software to clear status bits during a break interrupt, write a logic 1 to the
BCFE bit. If a status bit is cleared during the break state, it remains cleared when
the MCU exits the break state.
To protect status bits during the break state, write a logic 0 to the BCFE bit. With
BCFE at logic 0 (its default state), software can read and write I/O registers during
the break state without affecting status bits. Some status bits have a 2-step
read/write clearing procedure. If software does the first step on such a bit before
the break, the bit cannot change during the break state as long as BCFE is at logic
0. After the break, doing the second step clears the status bit.
Since the SPTE bit cannot be cleared during a break with the BCFE bit cleared, a
write to the transmit data register in break mode does not initiate a transmission nor
is this data transferred into the shift register. Therefore, a write to the SPDR in
break mode with the BCFE bit cleared has no effect.
21.12 I/O Signals
The SPI module has five I/O pins and shares four of them with a parallel I/O port.
They are:
•
MISO — Data received
•
MOSI — Data transmitted
•
SPSCK — Serial clock
•
SS — Slave select
•
CGND — Clock ground (internally connected to VSS)
The SPI has limited inter-integrated circuit (I2C) capability (requiring software
support) as a master in a single-master environment. To communicate with I2C
peripherals, MOSI becomes an open-drain output when the SPWOM bit in the SPI
control register is set. In I2C communication, the MOSI and MISO pins are
connected to a bidirectional pin from the I2C peripheral and through a pullup
resistor to VDD.
Data Sheet
290
MC68HC908GZ8
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
I/O Signals
21.12.1 MISO (Master In/Slave Out)
MISO is one of the two SPI module pins that transmits serial data. In full duplex
operation, the MISO pin of the master SPI module is connected to the MISO pin of
the slave SPI module. The master SPI simultaneously receives data on its MISO
pin and transmits data from its MOSI pin.
Freescale Semiconductor, Inc...
Slave output data on the MISO pin is enabled only when the SPI is configured as
a slave. The SPI is configured as a slave when its SPMSTR bit is logic 0 and its SS
pin is at logic 0. To support a multiple-slave system, a logic 1 on the SS pin puts
the MISO pin in a high-impedance state.
When enabled, the SPI controls data direction of the MISO pin regardless of the
state of the data direction register of the shared I/O port.
21.12.2 MOSI (Master Out/Slave In)
MOSI is one of the two SPI module pins that transmits serial data. In full-duplex
operation, the MOSI pin of the master SPI module is connected to the MOSI pin of
the slave SPI module. The master SPI simultaneously transmits data from its MOSI
pin and receives data on its MISO pin.
When enabled, the SPI controls data direction of the MOSI pin regardless of the
state of the data direction register of the shared I/O port.
21.12.3 SPSCK (Serial Clock)
The serial clock synchronizes data transmission between master and slave
devices. In a master MCU, the SPSCK pin is the clock output. In a slave MCU, the
SPSCK pin is the clock input. In full-duplex operation, the master and slave MCUs
exchange a byte of data in eight serial clock cycles.
When enabled, the SPI controls data direction of the SPSCK pin regardless of the
state of the data direction register of the shared I/O port.
21.12.4 SS (Slave Select)
The SS pin has various functions depending on the current state of the SPI. For an
SPI configured as a slave, the SS is used to select a slave. For CPHA = 0, the SS
is used to define the start of a transmission. (See 21.5 Transmission Formats.)
Since it is used to indicate the start of a transmission, the SS must be toggled high
and low between each byte transmitted for the CPHA = 0 format. However, it can
remain low between transmissions for the CPHA = 1 format. See Figure 21-12.
MC68HC908GZ8
MOTOROLA
Data Sheet
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
291
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
MISO/MOSI
BYTE 1
BYTE 2
BYTE 3
MASTER SS
SLAVE SS
CPHA = 0
SLAVE SS
CPHA = 1
Figure 21-12. CPHA/SS Timing
Freescale Semiconductor, Inc...
When an SPI is configured as a slave, the SS pin is always configured as an input.
It cannot be used as a general-purpose I/O regardless of the state of the MODFEN
control bit. However, the MODFEN bit can still prevent the state of the SS from
creating a MODF error. See 21.13.2 SPI Status and Control Register.
NOTE:
A logic 1 voltage on the SS pin of a slave SPI puts the MISO pin in a
high-impedance state. The slave SPI ignores all incoming SPSCK clocks, even if
it was already in the middle of a transmission.
When an SPI is configured as a master, the SS input can be used in conjunction
with the MODF flag to prevent multiple masters from driving MOSI and SPSCK.
(See 21.7.2 Mode Fault Error.) For the state of the SS pin to set the MODF flag,
the MODFEN bit in the SPSCK register must be set. If the MODFEN bit is low for
an SPI master, the SS pin can be used as a general-purpose I/O under the control
of the data direction register of the shared I/O port. With MODFEN high, it is an
input-only pin to the SPI regardless of the state of the data direction register of the
shared I/O port.
The CPU can always read the state of the SS pin by configuring the appropriate
pin as an input and reading the port data register. See Table 21-3.
Table 21-3. SPI Configuration
SPE
SPMSTR
MODFEN
SPI Configuration
State of SS Logic
0
X(1))
X
Not enabled
General-purpose I/O;
SS ignored by SPI
1
0
X
Slave
Input-only to SPI
1
1
0
Master without MODF
General-purpose I/O;
SS ignored by SPI
1
1
1
Master with MODF
Input-only to SPI
1. X = Don’t care
Data Sheet
292
MC68HC908GZ8
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
I/O Registers
21.12.5 CGND (Clock Ground)
CGND is the ground return for the serial clock pin, SPSCK, and the ground for the
port output buffers. It is internally connected to VSS as shown in Table 21-1.
21.13 I/O Registers
Freescale Semiconductor, Inc...
Three registers control and monitor SPI operation:
•
SPI control register (SPCR)
•
SPI status and control register (SPSCR)
•
SPI data register (SPDR)
21.13.1 SPI Control Register
The SPI control register:
•
Enables SPI module interrupt requests
•
Configures the SPI module as master or slave
•
Selects serial clock polarity and phase
•
Configures the SPSCK, MOSI, and MISO pins as open-drain outputs
•
Enables the SPI module
Address: $0010
Read:
Write:
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
SPRIE
R
SPMSTR
CPOL
CPHA
SPWOM
SPE
SPTIE
0
0
1
0
1
0
0
0
R
= Reserved
= Unimplemented
Figure 21-13. SPI Control Register (SPCR)
SPRIE — SPI Receiver Interrupt Enable Bit
This read/write bit enables CPU interrupt requests generated by the SPRF bit.
The SPRF bit is set when a byte transfers from the shift register to the receive
data register. Reset clears the SPRIE bit.
1 = SPRF CPU interrupt requests enabled
0 = SPRF CPU interrupt requests disabled
SPMSTR — SPI Master Bit
This read/write bit selects master mode operation or slave mode operation.
Reset sets the SPMSTR bit.
1 = Master mode
0 = Slave mode
MC68HC908GZ8
MOTOROLA
Data Sheet
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
293
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
CPOL — Clock Polarity Bit
This read/write bit determines the logic state of the SPSCK pin between
transmissions. (See Figure 21-4 and Figure 21-6.) To transmit data between
SPI modules, the SPI modules must have identical CPOL values. Reset clears
the CPOL bit.
Freescale Semiconductor, Inc...
CPHA — Clock Phase Bit
This read/write bit controls the timing relationship between the serial clock and
SPI data. (See Figure 21-4 and Figure 21-6.) To transmit data between SPI
modules, the SPI modules must have identical CPHA values. When CPHA = 0,
the SS pin of the slave SPI module must be set to logic 1 between bytes. (See
Figure 21-12.) Reset sets the CPHA bit.
SPWOM — SPI Wired-OR Mode Bit
This read/write bit disables the pullup devices on pins SPSCK, MOSI, and MISO
so that those pins become open-drain outputs.
1 = Wired-OR SPSCK, MOSI, and MISO pins
0 = Normal push-pull SPSCK, MOSI, and MISO pins
SPE — SPI Enable
This read/write bit enables the SPI module. Clearing SPE causes a partial reset
of the SPI. (See 21.9 Resetting the SPI.) Reset clears the SPE bit.
1 = SPI module enabled
0 = SPI module disabled
SPTIE— SPI Transmit Interrupt Enable
This read/write bit enables CPU interrupt requests generated by the SPTE bit.
SPTE is set when a byte transfers from the transmit data register to the shift
register. Reset clears the SPTIE bit.
1 = SPTE CPU interrupt requests enabled
0 = SPTE CPU interrupt requests disabled
21.13.2 SPI Status and Control Register
The SPI status and control register contains flags to signal these conditions:
•
Receive data register full
•
Failure to clear SPRF bit before next byte is received (overflow error)
•
Inconsistent logic level on SS pin (mode fault error)
•
Transmit data register empty
The SPI status and control register also contains bits that perform these functions:
•
Enable error interrupts
•
Enable mode fault error detection
•
Select master SPI baud rate
Data Sheet
294
MC68HC908GZ8
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
I/O Registers
Address: $0011
Bit 7
Read:
SPRF
Write:
Reset:
0
6
ERRIE
5
OVRF
0
0
= Unimplemented
4
MODF
3
SPTE
0
1
2
1
Bit 0
MODFEN
SPR1
SPR0
0
0
0
Figure 21-14. SPI Status and Control Register (SPSCR)
Freescale Semiconductor, Inc...
SPRF — SPI Receiver Full Bit
This clearable, read-only flag is set each time a byte transfers from the shift
register to the receive data register. SPRF generates a CPU interrupt request if
the SPRIE bit in the SPI control register is set also.
During an SPRF CPU interrupt, the CPU clears SPRF by reading the SPI status
and control register with SPRF set and then reading the SPI data register.
Reset clears the SPRF bit.
1 = Receive data register full
0 = Receive data register not full
ERRIE — Error Interrupt Enable Bit
This read/write bit enables the MODF and OVRF bits to generate CPU interrupt
requests. Reset clears the ERRIE bit.
1 = MODF and OVRF can generate CPU interrupt requests
0 = MODF and OVRF cannot generate CPU interrupt requests
OVRF — Overflow Bit
This clearable, read-only flag is set if software does not read the byte in the
receive data register before the next full byte enters the shift register. In an
overflow condition, the byte already in the receive data register is unaffected,
and the byte that shifted in last is lost. Clear the OVRF bit by reading the SPI
status and control register with OVRF set and then reading the receive data
register. Reset clears the OVRF bit.
1 = Overflow
0 = No overflow
MODF — Mode Fault Bit
This clearable, read-only flag is set in a slave SPI if the SS pin goes high during
a transmission with the MODFEN bit set. In a master SPI, the MODF flag is set
if the SS pin goes low at any time with the MODFEN bit set. Clear the MODF bit
by reading the SPI status and control register (SPSCR) with MODF set and then
writing to the SPI control register (SPCR). Reset clears the MODF bit.
1 = SS pin at inappropriate logic level
0 = SS pin at appropriate logic level
SPTE — SPI Transmitter Empty Bit
This clearable, read-only flag is set each time the transmit data register
transfers a byte into the shift register. SPTE generates an SPTE CPU interrupt
request or an SPTE DMA service request if the SPTIE bit in the SPI control
register is set also.
MC68HC908GZ8
MOTOROLA
Data Sheet
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
295
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
NOTE:
Do not write to the SPI data register unless the SPTE bit is high.
During an SPTE CPU interrupt, the CPU clears the SPTE bit by writing to the
transmit data register.
Reset sets the SPTE bit.
1 = Transmit data register empty
0 = Transmit data register not empty
Freescale Semiconductor, Inc...
MODFEN — Mode Fault Enable Bit
This read/write bit, when set to 1, allows the MODF flag to be set. If the MODF
flag is set, clearing the MODFEN does not clear the MODF flag. If the SPI is
enabled as a master and the MODFEN bit is low, then the SS pin is available as
a general-purpose I/O.
If the MODFEN bit is set, then this pin is not available as a general-purpose I/O.
When the SPI is enabled as a slave, the SS pin is not available as a
general-purpose I/O regardless of the value of MODFEN. See 21.12.4 SS
(Slave Select).
If the MODFEN bit is low, the level of the SS pin does not affect the operation
of an enabled SPI configured as a master. For an enabled SPI configured as a
slave, having MODFEN low only prevents the MODF flag from being set. It does
not affect any other part of SPI operation. See 21.7.2 Mode Fault Error.
SPR1 and SPR0 — SPI Baud Rate Select Bits
In master mode, these read/write bits select one of four baud rates as shown in
Table 21-4. SPR1 and SPR0 have no effect in slave mode. Reset clears SPR1
and SPR0.
Table 21-4. SPI Master Baud Rate Selection
SPR1 and SPR0
Baud Rate Divisor (BD)
00
2
01
8
10
32
11
128
Use this formula to calculate the SPI baud rate:
CGMOUT
Baud rate = -------------------------2 × BD
where:
CGMOUT = base clock output of the clock generator module (CGM)
BD = baud rate divisor
Data Sheet
296
MC68HC908GZ8
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Serial Peripheral Interface (SPI) Module
I/O Registers
21.13.3 SPI Data Register
The SPI data register consists of the read-only receive data register and the
write-only transmit data register. Writing to the SPI data register writes data into the
transmit data register. Reading the SPI data register reads data from the receive
data register. The transmit data and receive data registers are separate registers
that can contain different values. See Figure 21-2.
Freescale Semiconductor, Inc...
Address: $0012
Bit 7
6
5
4
3
2
1
Bit 0
Read:
R7
R6
R5
R4
R3
R2
R1
R0
Write:
T7
T6
T5
T4
T3
T2
T1
T0
Reset:
Unaffected by reset
Figure 21-15. SPI Data Register (SPDR)
R7–R0/T7–T0 — Receive/Transmit Data Bits
NOTE:
Do not use read-modify-write instructions on the SPI data register since the register
read is not the same as the register written.
MC68HC908GZ8
MOTOROLA
Data Sheet
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
297
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Serial Peripheral Interface (SPI) Module
Data Sheet
298
MC68HC908GZ8
Serial Peripheral Interface (SPI) Module
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 22. Timebase Module (TBM)
Freescale Semiconductor, Inc...
22.1 Introduction
This section describes the timebase module (TBM). The TBM will generate
periodic interrupts at user selectable rates using a counter clocked by the external
clock source. This TBM version uses 15 divider stages, eight of which are user
selectable. A configuration option bit to select an additional 128 divide of the
external clock source can be selected. See Section 8. Configuration Register
(CONFIG)
22.2 Features
Features of the TBM module include:
•
External clock or an additional divide-by-128 selected by configuration
option bit as clock source
•
Software configurable periodic interrupts with divide-by: 8, 16, 32, 64, 128,
2048, 8192, and 32768 taps of the selected clock source
•
Configurable for operation during stop mode to allow periodic wakeup from
stop
22.3 Functional Description
This module can generate a periodic interrupt by dividing the clock source supplied
from the clock generator module, CGMXCLK.
The counter is initialized to all 0s when TBON bit is cleared. The counter, shown in
Figure 22-1, starts counting when the TBON bit is set. When the counter overflows
at the tap selected by TBR2–TBR0, the TBIF bit gets set. If the TBIE bit is set, an
interrupt request is sent to the CPU. The TBIF flag is cleared by writing a 1 to the
TACK bit. The first time the TBIF flag is set after enabling the timebase module, the
interrupt is generated at approximately half of the overflow period. Subsequent
events occur at the exact period.
The timebase module may remain active after execution of the STOP instruction if
the crystal oscillator has been enabled to operate during stop mode through the
OSCENINSTOP bit in the configuration register. The timebase module can be
used in this mode to generate a periodic wakeup from stop mode.
MC68HC908GZ8
MOTOROLA
Data Sheet
Timebase Module (TBM)
For More Information On This Product,
Go to: www.freescale.com
299
Freescale Semiconductor, Inc.
Timebase Module (TBM)
22.4 Interrupts
The timebase module can periodically interrupt the CPU with a rate defined by the
selected TBMCLK and the select bits TBR2–TBR0. When the timebase counter
chain rolls over, the TBIF flag is set. If the TBIE bit is set, enabling the timebase
interrupt, the counter chain overflow will generate a CPU interrupt request.
CGMXCLK
FROM CGM MODULE
TBMCLK
0
1
DIVIDE BY 128
PRESCALER
TBON
÷2
÷2
÷2
÷2
÷2
÷2
÷2
÷2
÷2
÷2
÷2
÷2
÷2
TACK
÷2
TBR0
÷2
TBR1
TBMINT
TBR2
TBIF
000
TBIE
R
001
010
011
100
SEL
Freescale Semiconductor, Inc...
TBMCLKSEL
FROM CONFIG2
101
110
111
Figure 22-1. Timebase Block Diagram
NOTE:
Interrupts must be acknowledged by writing a logic 1 to the TACK bit.
Data Sheet
300
MC68HC908GZ8
Timebase Module (TBM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Timebase Module (TBM)
TBM Interrupt Rate
22.5 TBM Interrupt Rate
The interrupt rate is determined by the equation:
t
TBMRATE
1
Divider
= -------------------------------- = ---------------------------f
f
TBMRATE
TBMCLK
where:
fTBMCLK =Frequency supplied from the clock generator (CGM) module
Divider =Divider value as determined by TBR2–TBR0 settings, see Table 22-1
Freescale Semiconductor, Inc...
Table 22-1. Timebase Divider Selection
Divider Tap
TBR2
TBR1
TBR0
TMBCLKSEL
0
1
0
0
0
32,768
4,194,304
0
0
1
8192
1,048,576
0
1
0
2048
262144
0
1
1
128
16,384
1
0
0
64
8192
1
0
1
32
4096
1
1
0
16
2048
1
1
1
8
1024
As an example, a clock source of 4.9152 MHz, with the TMCLKSEL set for
divide-by-128 and the TBR2–TBR0 set to {011}, the divider tap is1 and the interrupt
rate calculates to:
1/(4.9152 x 106/128) = 26 µs
NOTE:
Do not change TBR2–TBR0 bits while the timebase is enabled
(TBON = 1).
22.6 Low-Power Modes
The WAIT and STOP instructions put the MCU in low power- consumption standby
modes.
22.6.1 Wait Mode
The timebase module remains active after execution of the WAIT instruction. In
wait mode the timebase register is not accessible by the CPU.
If the timebase functions are not required during wait mode, reduce the power
consumption by stopping the timebase before executing the WAIT instruction.
MC68HC908GZ8
MOTOROLA
Data Sheet
Timebase Module (TBM)
For More Information On This Product,
Go to: www.freescale.com
301
Freescale Semiconductor, Inc.
Timebase Module (TBM)
22.6.2 Stop Mode
The timebase module may remain active after execution of the STOP instruction if
the internal clock generator has been enabled to operate during stop mode through
the OSCENINSTOP bit in the configuration register. The timebase module can be
used in this mode to generate a periodic wakeup from stop mode.
Freescale Semiconductor, Inc...
If the internal clock generator has not been enabled to operate in stop mode, the
timebase module will not be active during stop mode. In stop mode, the timebase
register is not accessible by the CPU.
If the timebase functions are not required during stop mode, reduce power
consumption by disabling the timebase module before executing the STOP
instruction.
22.7 Timebase Control Register
The timebase has one register, the timebase control register (TBCR), which is
used to enable the timebase interrupts and set the rate.
Address: $001C
Bit 7
Read:
TBIF
Write:
Reset:
0
6
5
4
TBR2
TBR1
TBR0
0
0
0
= Unimplemented
3
2
1
Bit 0
TBIE
TBON
R
0
0
0
0
R
= Reserved
0
TACK
Figure 22-2. Timebase Control Register (TBCR)
TBIF — Timebase Interrupt Flag
This read-only flag bit is set when the timebase counter has rolled over.
1 = Timebase interrupt pending
0 = Timebase interrupt not pending
TBR2–TBR0 — Timebase Divider Selection Bits
These read/write bits select the tap in the counter to be used for timebase
interrupts as shown in Table 22-1.
NOTE:
Do not change TBR2–TBR0 bits while the timebase is enabled
(TBON = 1).
TACK— Timebase Acknowledge Bit
The TACK bit is a write-only bit and always reads as 0. Writing a logic 1 to this
bit clears TBIF, the timebase interrupt flag bit. Writing a logic 0 to this bit has no
effect.
1 = Clear timebase interrupt flag
0 = No effect
Data Sheet
302
MC68HC908GZ8
Timebase Module (TBM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Timebase Module (TBM)
Timebase Control Register
TBIE — Timebase Interrupt Enabled Bit
This read/write bit enables the timebase interrupt when the TBIF bit becomes
set. Reset clears the TBIE bit.
1 = Timebase interrupt is enabled.
0 = Timebase interrupt is disabled.
Freescale Semiconductor, Inc...
TBON — Timebase Enabled Bit
This read/write bit enables the timebase. Timebase may be turned off to reduce
power consumption when its function is not necessary. The counter can be
initialized by clearing and then setting this bit. Reset clears the TBON bit.
1 = Timebase is enabled.
0 = Timebase is disabled and the counter initialized to 0s.
MC68HC908GZ8
MOTOROLA
Data Sheet
Timebase Module (TBM)
For More Information On This Product,
Go to: www.freescale.com
303
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Timebase Module (TBM)
Data Sheet
304
MC68HC908GZ8
Timebase Module (TBM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 23. Timer Interface Module (TIM)
23.1 Introduction
Freescale Semiconductor, Inc...
This section describes the timer interface (TIM) module. The TIM is a two-channel
timer that provides a timing reference with input capture, output compare, and
pulse-width-modulation functions. Figure 23-1 is a block diagram of the TIM.
This particular MCU has two timer interface modules which are denoted as TIM1
and TIM2.
PRESCALER SELECT
INTERNAL
BUS CLOCK
PRESCALER
TSTOP
PS2
TRST
PS1
PS0
16-BIT COUNTER
TOF
TOIE
INTERRUPT
LOGIC
16-BIT COMPARATOR
TMODH:TMODL
TOV0
CHANNEL 0
ELS0B
ELS0A
CH0MAX
16-BIT COMPARATOR
TCH0H:TCH0L
PORT
LOGIC
T[1,2]CH0
CH0F
16-BIT LATCH
CH0IE
MS0A
INTERRUPT
LOGIC
MS0B
INTERNAL BUS
TOV1
CHANNEL 1
ELS1B
ELS1A
CH1MAX
PORT
LOGIC
T[1,2]CH1
16-BIT COMPARATOR
TCH1H:TCH1L
CH1F
16-BIT LATCH
MS1A
CH1IE
INTERRUPT
LOGIC
Figure 23-1. TIM Block Diagram
MC68HC908GZ8
MOTOROLA
Data Sheet
Timer Interface Module (TIM)
For More Information On This Product,
Go to: www.freescale.com
305
Freescale Semiconductor, Inc.
Timer Interface Module (TIM)
23.2 Features
Freescale Semiconductor, Inc...
Features of the TIM include:
•
Two input capture/output compare channels:
– Rising-edge, falling-edge, or any-edge input capture trigger
– Set, clear, or toggle output compare action
•
Buffered and unbuffered pulse-width-modulation (PWM) signal generation
•
Programmable TIM clock input with 7-frequency internal bus clock prescaler
selection
•
Free-running or modulo up-count operation
•
Toggle any channel pin on overflow
•
TIM counter stop and reset bits
23.3 Pin Name Conventions
The text that follows describes both timers, TIM1 and TIM2. The TIM input/output
(I/O) pin names are T[1,2]CH0 (timer channel 0) and T[1,2]CH1 (timer channel 1),
where “1” is used to indicate TIM1 and “2” is used to indicate TIM2. The two TIMs
share four I/O pins with four port D I/O port pins. The full names of the TIM I/O pins
are listed in
Table 23-1. The generic pin names appear in the text that follows.
Table 23-1. Pin Name Conventions
TIM Generic Pin Names:
T[1,2]CH0
T[1,2]CH1
TIM1
PTD4/T1CH0
PTD5/T1CH1
TIM2
PTD6/T2CH0
PTD7/T2CH1
Full TIM Pin Names:
NOTE:
References to either timer 1 or timer 2 may be made in the following text by omitting
the timer number. For example, TCH0 may refer generically to T1CH0 and T2CH0,
and TCH1 may refer to T1CH1 and T2CH1.
23.4 Functional Description
Figure 23-1 shows the structure of the TIM. The central component of the TIM is
the 16-bit TIM counter that can operate as a free-running counter or a modulo
up-counter. The TIM counter provides the timing reference for the input capture
and output compare functions. The TIM counter modulo registers,
TMODH:TMODL, control the modulo value of the TIM counter. Software can read
the TIM counter value at any time without affecting the counting sequence.
The two TIM channels (per timer) are programmable independently as input
capture or output compare channels. If a channel is configured as input capture,
Data Sheet
306
MC68HC908GZ8
Timer Interface Module (TIM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Timer Interface Module (TIM)
Functional Description
then an internal pullup device may be enabled for that channel. See 17.5.3 Port D
Input Pullup Enable Register.
Figure 23-2 summarizes the timer registers.
NOTE:
Addr.
Freescale Semiconductor, Inc...
$0020
$0021
$0022
References to either timer 1 or timer 2 may be made in the following text by omitting
the timer number. For example, TSC may generically refer to both T1SC and
T2SC.
Register Name
Bit 7
TSTOP
3
0
0
2
1
Bit 0
PS2
PS1
PS0
0
0
1
0
0
0
0
0
Timer 1 Counter Read:
Register High (T1CNTH) Write:
See page 317. Reset:
Bit 15
14
13
12
11
10
9
Bit 8
0
0
0
0
0
0
0
0
Timer 1 Counter Read:
Register Low (T1CNTL) Write:
See page 317. Reset:
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
Bit 15
14
13
12
11
10
9
Bit 8
1
1
1
1
1
1
1
1
Bit 7
6
5
4
3
2
1
Bit 0
1
1
1
1
1
1
1
1
CH0IE
MS0B
MS0A
ELS0B
ELS0A
TOV0
CH0MAX
0
0
0
0
0
0
0
0
Bit 15
14
13
12
11
10
9
Bit 8
2
1
Bit 0
Timer 1 Counter Modulo Read:
Register Low (T1MODL) Write:
See page 318. Reset:
$0026
Timer 1 Channel 0 Read:
Register High (T1CH0H) Write:
See page 321. Reset:
$0027
Timer 1 Channel 0 Read:
Register Low (T1CH0L) Write:
See page 321. Reset:
$0029
TOIE
4
TOF
Timer 1 Channel 0 Status and Read:
$0025
Control Register (T1SC0) Write:
See page 318. Reset:
$0028
5
Timer 1 Status and Control Read:
Register (T1SC) Write:
See page 315. Reset:
Timer 1 Counter Modulo Reg- Read:
$0023
ister High (T1MODH) Write:
See page 317. Reset:
$0024
6
Timer 1 Channel 1 Status and Read:
Control Register (T1SC1) Write:
See page 318. Reset:
Timer 1 Channel 1 Read:
Register High (T1CH1H) Write:
See page 322. Reset:
0
CH0F
0
TRST
Indeterminate after reset
Bit 7
6
5
4
3
Indeterminate after reset
CH1F
0
0
CH1IE
MS1A
ELS1B
ELS1A
TOV1
CH1MAX
0
0
0
0
0
0
0
0
Bit 15
14
13
12
11
10
9
Bit 8
Indeterminate after reset
= Unimplemented
Figure 23-2. TIM I/O Register Summary (Sheet 1 of 2)
MC68HC908GZ8
MOTOROLA
Data Sheet
Timer Interface Module (TIM)
For More Information On This Product,
Go to: www.freescale.com
307
Freescale Semiconductor, Inc.
Timer Interface Module (TIM)
Addr.
Register Name
Timer 1 Channel 1 Read:
Register Low (T1CH1L) Write:
See page 322. Reset:
$002A
$002B
Freescale Semiconductor, Inc...
6
5
4
3
2
1
Bit 0
Bit 7
6
5
4
3
2
1
Bit 0
PS2
PS1
PS0
Indeterminate after reset
Timer 2 Status and Control Read:
Register (T2SC) Write:
See page 315. Reset:
TOF
$002C
$002D
0
0
1
0
0
0
0
0
Timer 2 Counter Read:
Register High (T2CNTH) Write:
See page 317. Reset:
Bit 15
14
13
12
11
10
9
Bit 8
0
0
0
0
0
0
0
0
Timer 2 Counter Read:
Register Low (T2CNTL) Write:
See page 317. Reset:
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
Bit 15
14
13
12
11
10
9
Bit 8
1
1
1
1
1
1
1
1
Bit 7
6
5
4
3
2
1
Bit 0
1
1
1
1
1
1
1
1
CH0IE
MS0B
MS0A
ELS0B
ELS0A
TOV0
CH0MAX
0
0
0
0
0
0
0
0
Bit 15
14
13
12
11
10
9
Bit 8
2
1
Bit 0
Timer 2 Channel 0 Status and Read:
$0030
Control Register (T2SC0) Write:
See page 318. Reset:
$0031
Timer 2 Channel 0 Read:
Register High (T2CH0H) Write:
See page 321. Reset:
$0032
Timer 2 Channel 0 Read:
Register Low (T2CH0L) Write:
See page 321. Reset:
Timer 2 Channel 1 Status and Read:
Control Register (T2SC1) Write:
See page 318. Reset:
$0034
$0035
0
TSTOP
Timer 2 Counter Modulo Read:
Register Low (T2MODL) Write:
See page 318. Reset:
$002F
0
TOIE
Timer 2 Counter Modulo Reg- Read:
$002E
ister High (T2MODH) Write:
See page 317. Reset:
$0033
Bit 7
Timer 2 Channel 1 Read:
Register High (T2CH1H) Write:
See page 322. Reset:
Timer 2 Channel 1 Read:
Register Low (T2CH1L) Write:
See page 322. Reset:
0
CH0F
0
TRST
Indeterminate after reset
Bit 7
6
5
4
3
Indeterminate after reset
CH1F
0
0
CH1IE
MS1A
ELS1B
ELS1A
TOV1
CH1MAX
0
0
0
0
0
0
0
0
Bit 15
14
13
12
11
10
9
Bit 8
2
1
Bit 0
Indeterminate after reset
Bit 7
6
5
4
3
Indeterminate after reset
= Unimplemented
Figure 23-2. TIM I/O Register Summary (Sheet 2 of 2)
Data Sheet
308
MC68HC908GZ8
Timer Interface Module (TIM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Timer Interface Module (TIM)
Functional Description
23.4.1 TIM Counter Prescaler
The TIM clock source can be one of the seven prescaler outputs. The prescaler
generates seven clock rates from the internal bus clock. The prescaler select bits,
PS[2:0], in the TIM status and control register select the TIM clock source.
Freescale Semiconductor, Inc...
23.4.2 Input Capture
With the input capture function, the TIM can capture the time at which an external
event occurs. When an active edge occurs on the pin of an input capture channel,
the TIM latches the contents of the TIM counter into the TIM channel registers,
TCHxH:TCHxL. The polarity of the active edge is programmable. Input captures
can generate TIM CPU interrupt requests.
23.4.3 Output Compare
With the output compare function, the TIM can generate a periodic pulse with a
programmable polarity, duration, and frequency. When the counter reaches the
value in the registers of an output compare channel, the TIM can set, clear, or
toggle the channel pin. Output compares can generate TIM CPU interrupt
requests.
23.4.3.1 Unbuffered Output Compare
Any output compare channel can generate unbuffered output compare pulses as
described in 23.4.3 Output Compare. The pulses are unbuffered because
changing the output compare value requires writing the new value over the old
value currently in the TIM channel registers.
An unsynchronized write to the TIM channel registers to change an output compare
value could cause incorrect operation for up to two counter overflow periods. For
example, writing a new value before the counter reaches the old value but after the
counter reaches the new value prevents any compare during that counter overflow
period. Also, using a TIM overflow interrupt routine to write a new, smaller output
compare value may cause the compare to be missed. The TIM may pass the new
value before it is written.
Use the following methods to synchronize unbuffered changes in the output
compare value on channel x:
•
When changing to a smaller value, enable channel x output compare
interrupts and write the new value in the output compare interrupt routine.
The output compare interrupt occurs at the end of the current output
compare pulse. The interrupt routine has until the end of the counter
overflow period to write the new value.
•
When changing to a larger output compare value, enable TIM overflow
interrupts and write the new value in the TIM overflow interrupt routine. The
TIM overflow interrupt occurs at the end of the current counter overflow
MC68HC908GZ8
MOTOROLA
Data Sheet
Timer Interface Module (TIM)
For More Information On This Product,
Go to: www.freescale.com
309
Freescale Semiconductor, Inc.
Timer Interface Module (TIM)
period. Writing a larger value in an output compare interrupt routine (at the
end of the current pulse) could cause two output compares to occur in the
same counter overflow period.
23.4.3.2 Buffered Output Compare
Freescale Semiconductor, Inc...
Channels 0 and 1 can be linked to form a buffered output compare channel whose
output appears on the TCH0 pin. The TIM channel registers of the linked pair
alternately control the output.
Setting the MS0B bit in TIM channel 0 status and control register (TSC0) links
channel 0 and channel 1. The output compare value in the TIM channel 0 registers
initially controls the output on the TCH0 pin. Writing to the TIM channel 1 registers
enables the TIM channel 1 registers to synchronously control the output after the
TIM overflows. At each subsequent overflow, the TIM channel registers (0 or 1) that
control the output are the ones written to last. TSC0 controls and monitors the
buffered output compare function, and TIM channel 1 status and control register
(TSC1) is unused. While the MS0B bit is set, the channel 1 pin, TCH1, is available
as a general-purpose I/O pin.
NOTE:
In buffered output compare operation, do not write new output compare values to
the currently active channel registers. User software should track the currently
active channel to prevent writing a new value to the active channel. Writing to the
active channel registers is the same as generating unbuffered output compares.
23.4.4 Pulse Width Modulation (PWM)
By using the toggle-on-overflow feature with an output compare channel, the TIM
can generate a PWM signal. The value in the TIM counter modulo registers
determines the period of the PWM signal. The channel pin toggles when the
counter reaches the value in the TIM counter modulo registers. The time between
overflows is the period of the PWM signal.
As Figure 23-3 shows, the output compare value in the TIM channel registers
determines the pulse width of the PWM signal. The time between overflow and
output compare is the pulse width. Program the TIM to clear the channel pin on
output compare if the state of the PWM pulse is logic 1. Program the TIM to set the
pin if the state of the PWM pulse is logic 0.
The value in the TIM counter modulo registers and the selected prescaler output
determines the frequency of the PWM output. The frequency of an 8-bit PWM
signal is variable in 256 increments. Writing $00FF (255) to the TIM counter
modulo registers produces a PWM period of 256 times the internal bus clock period
if the prescaler select value is $000. See 23.9.1 TIM Status and Control Register.
Data Sheet
310
MC68HC908GZ8
Timer Interface Module (TIM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Timer Interface Module (TIM)
Functional Description
OVERFLOW
OVERFLOW
OVERFLOW
PERIOD
PULSE
WIDTH
Freescale Semiconductor, Inc...
TCHx
OUTPUT
COMPARE
OUTPUT
COMPARE
OUTPUT
COMPARE
Figure 23-3. PWM Period and Pulse Width
The value in the TIM channel registers determines the pulse width of the PWM
output. The pulse width of an 8-bit PWM signal is variable in 256 increments.
Writing $0080 (128) to the TIM channel registers produces a duty cycle of 128/256
or 50%.
23.4.4.1 Unbuffered PWM Signal Generation
Any output compare channel can generate unbuffered PWM pulses as described
in 23.4.4 Pulse Width Modulation (PWM). The pulses are unbuffered because
changing the pulse width requires writing the new pulse width value over the old
value currently in the TIM channel registers.
An unsynchronized write to the TIM channel registers to change a pulse width
value could cause incorrect operation for up to two PWM periods. For example,
writing a new value before the counter reaches the old value but after the counter
reaches the new value prevents any compare during that PWM period. Also, using
a TIM overflow interrupt routine to write a new, smaller pulse width value may
cause the compare to be missed. The TIM may pass the new value before it is
written.
Use the following methods to synchronize unbuffered changes in the PWM pulse
width on channel x:
•
When changing to a shorter pulse width, enable channel x output compare
interrupts and write the new value in the output compare interrupt routine.
The output compare interrupt occurs at the end of the current pulse. The
interrupt routine has until the end of the PWM period to write the new value.
•
When changing to a longer pulse width, enable TIM overflow interrupts and
write the new value in the TIM overflow interrupt routine. The TIM overflow
interrupt occurs at the end of the current PWM period. Writing a larger value
in an output compare interrupt routine (at the end of the current pulse) could
cause two output compares to occur in the same PWM period.
MC68HC908GZ8
MOTOROLA
Data Sheet
Timer Interface Module (TIM)
For More Information On This Product,
Go to: www.freescale.com
311
Freescale Semiconductor, Inc.
Timer Interface Module (TIM)
NOTE:
In PWM signal generation, do not program the PWM channel to toggle on output
compare. Toggling on output compare prevents reliable 0% duty cycle generation
and removes the ability of the channel to self-correct in the event of software error
or noise. Toggling on output compare also can cause incorrect PWM signal
generation when changing the PWM pulse width to a new, much larger value.
23.4.4.2 Buffered PWM Signal Generation
Freescale Semiconductor, Inc...
Channels 0 and 1 can be linked to form a buffered PWM channel whose output
appears on the TCH0 pin. The TIM channel registers of the linked pair alternately
control the pulse width of the output.
Setting the MS0B bit in TIM channel 0 status and control register (TSC0) links
channel 0 and channel 1. The TIM channel 0 registers initially control the pulse
width on the TCH0 pin. Writing to the TIM channel 1 registers enables the TIM
channel 1 registers to synchronously control the pulse width at the beginning of the
next PWM period. At each subsequent overflow, the TIM channel registers (0 or 1)
that control the pulse width are the ones written to last. TSC0 controls and monitors
the buffered PWM function, and TIM channel 1 status and control register (TSC1)
is unused. While the MS0B bit is set, the channel 1 pin, TCH1, is available as a
general-purpose I/O pin.
NOTE:
In buffered PWM signal generation, do not write new pulse width values to the
currently active channel registers. User software should track the currently active
channel to prevent writing a new value to the active channel. Writing to the active
channel registers is the same as generating unbuffered PWM signals.
23.4.4.3 PWM Initialization
To ensure correct operation when generating unbuffered or buffered PWM signals,
use the following initialization procedure:
1. In the TIM status and control register (TSC):
a. Stop the TIM counter by setting the TIM stop bit, TSTOP.
b. Reset the TIM counter and prescaler by setting the TIM reset bit,
TRST.
2. In the TIM counter modulo registers (TMODH:TMODL), write the value for
the required PWM period.
3. In the TIM channel x registers (TCHxH:TCHxL), write the value for the
required pulse width.
4. In TIM channel x status and control register (TSCx):
a. Write 0:1 (for unbuffered output compare or PWM signals) or 1:0 (for
buffered output compare or PWM signals) to the mode select bits,
MSxB:MSxA. See Table 23-3.
b. Write 1 to the toggle-on-overflow bit, TOVx.
Data Sheet
312
MC68HC908GZ8
Timer Interface Module (TIM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Timer Interface Module (TIM)
Interrupts
c. Write 1:0 (to clear output on compare) or 1:1 (to set output on compare)
to the edge/level select bits, ELSxB:ELSxA. The output action on
compare must force the output to the complement of the pulse width
level. See Table 23-3.
NOTE:
In PWM signal generation, do not program the PWM channel to toggle on output
compare. Toggling on output compare prevents reliable 0% duty cycle generation
and removes the ability of the channel to self-correct in the event of software error
or noise. Toggling on output compare can also cause incorrect PWM signal
generation when changing the PWM pulse width to a new, much larger value.
Freescale Semiconductor, Inc...
5. In the TIM status control register (TSC), clear the TIM stop bit, TSTOP.
Setting MS0B links channels 0 and 1 and configures them for buffered PWM
operation. The TIM channel 0 registers (TCH0H:TCH0L) initially control the
buffered PWM output. TIM status control register 0 (TSCR0) controls and monitors
the PWM signal from the linked channels.
Clearing the toggle-on-overflow bit, TOVx, inhibits output toggles on TIM overflows.
Subsequent output compares try to force the output to a state it is already in and
have no effect. The result is a 0% duty cycle output.
Setting the channel x maximum duty cycle bit (CHxMAX) and setting the TOVx bit
generates a 100% duty cycle output. See 23.9.4 TIM Channel Status and Control
Registers.
23.5 Interrupts
The following TIM sources can generate interrupt requests:
•
TIM overflow flag (TOF) — The TOF bit is set when the TIM counter reaches
the modulo value programmed in the TIM counter modulo registers. The TIM
overflow interrupt enable bit, TOIE, enables TIM overflow CPU interrupt
requests. TOF and TOIE are in the TIM status and control register.
•
TIM channel flags (CH1F:CH0F) — The CHxF bit is set when an input
capture or output compare occurs on channel x. Channel x TIM CPU
interrupt requests are controlled by the channel x interrupt enable bit,
CHxIE. Channel x TIM CPU interrupt requests are enabled when CHxIE =
1. CHxF and CHxIE are in the TIM channel x status and control register.
23.6 Low-Power Modes
The WAIT and STOP instructions put the MCU in low power- consumption standby
modes.
MC68HC908GZ8
MOTOROLA
Data Sheet
Timer Interface Module (TIM)
For More Information On This Product,
Go to: www.freescale.com
313
Freescale Semiconductor, Inc.
Timer Interface Module (TIM)
23.6.1 Wait Mode
The TIM remains active after the execution of a WAIT instruction. In wait mode, the
TIM registers are not accessible by the CPU. Any enabled CPU interrupt request
from the TIM can bring the MCU out of wait mode.
If TIM functions are not required during wait mode, reduce power consumption by
stopping the TIM before executing the WAIT instruction.
Freescale Semiconductor, Inc...
23.6.2 Stop Mode
The TIM is inactive after the execution of a STOP instruction. The STOP instruction
does not affect register conditions or the state of the TIM counter. TIM operation
resumes when the MCU exits stop mode after an external interrupt.
23.7 TIM During Break Interrupts
A break interrupt stops the TIM counter.
The system integration module (SIM) controls whether status bits in other modules
can be cleared during the break state. The BCFE bit in the SIM break flag control
register (SBFCR) enables software to clear status bits during the break state. See
20.7.3 Break Flag Control Register.
To allow software to clear status bits during a break interrupt, write a logic 1 to the
BCFE bit. If a status bit is cleared during the break state, it remains cleared when
the MCU exits the break state.
To protect status bits during the break state, write a logic 0 to the BCFE bit. With
BCFE at logic 0 (its default state), software can read and write I/O registers during
the break state without affecting status bits. Some status bits have a 2-step
read/write clearing procedure. If software does the first step on such a bit before
the break, the bit cannot change during the break state as long as BCFE is at logic
0. After the break, doing the second step clears the status bit.
23.8 I/O Signals
Port D shares four of its pins with the TIM. The four TIM channel I/O pins are
T1CH0, T1CH1, T2CH0, and T2CH1 as described in 23.3 Pin Name
Conventions.
Each channel I/O pin is programmable independently as an input capture pin or an
output compare pin. T1CH0 and T2CH0 can be configured as buffered output
compare or buffered PWM pins.
Data Sheet
314
MC68HC908GZ8
Timer Interface Module (TIM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Timer Interface Module (TIM)
I/O Registers
23.9 I/O Registers
NOTE:
References to either timer 1 or timer 2 may be made in the following text by omitting
the timer number. For example, TSC may generically refer to both T1SC AND
T2SC.
Freescale Semiconductor, Inc...
These I/O registers control and monitor operation of the TIM:
•
TIM status and control register (TSC)
•
TIM counter registers (TCNTH:TCNTL)
•
TIM counter modulo registers (TMODH:TMODL)
•
TIM channel status and control registers (TSC0 and TSC1)
•
TIM channel registers (TCH0H:TCH0L, TCH1H:TCH1L)
23.9.1 TIM Status and Control Register
The TIM status and control register (TSC):
•
Enables TIM overflow interrupts
•
Flags TIM overflows
•
Stops the TIM counter
•
Resets the TIM counter
•
Prescales the TIM counter clock
Address: T1SC, $0020 and T2SC, $002B
Bit 7
Read:
TOF
Write:
0
Reset:
0
6
5
TOIE
TSTOP
0
1
4
3
0
0
TRST
0
0
2
1
Bit 0
PS2
PS1
PS0
0
0
0
= Unimplemented
Figure 23-4. TIM Status and Control Register (TSC)
TOF — TIM Overflow Flag Bit
This read/write flag is set when the TIM counter reaches the modulo value
programmed in the TIM counter modulo registers. Clear TOF by reading the TIM
status and control register when TOF is set and then writing a logic 0 to TOF. If
another TIM overflow occurs before the clearing sequence is complete, then
writing logic 0 to TOF has no effect. Therefore, a TOF interrupt request cannot
be lost due to inadvertent clearing of TOF. Reset clears the TOF bit. Writing a
logic 1 to TOF has no effect.
1 = TIM counter has reached modulo value
0 = TIM counter has not reached modulo value
MC68HC908GZ8
MOTOROLA
Data Sheet
Timer Interface Module (TIM)
For More Information On This Product,
Go to: www.freescale.com
315
Freescale Semiconductor, Inc.
Timer Interface Module (TIM)
TOIE — TIM Overflow Interrupt Enable Bit
This read/write bit enables TIM overflow interrupts when the TOF bit becomes
set. Reset clears the TOIE bit.
1 = TIM overflow interrupts enabled
0 = TIM overflow interrupts disabled
Freescale Semiconductor, Inc...
TSTOP — TIM Stop Bit
This read/write bit stops the TIM counter. Counting resumes when TSTOP is
cleared. Reset sets the TSTOP bit, stopping the TIM counter until software
clears the TSTOP bit.
1 = TIM counter stopped
0 = TIM counter active
NOTE:
Do not set the TSTOP bit before entering wait mode if the TIM is required to exit
wait mode.
TRST — TIM Reset Bit
Setting this write-only bit resets the TIM counter and the TIM prescaler. Setting
TRST has no effect on any other registers. Counting resumes from $0000.
TRST is cleared automatically after the TIM counter is reset and always reads
as logic 0. Reset clears the TRST bit.
1 = Prescaler and TIM counter cleared
0 = No effect
NOTE:
Setting the TSTOP and TRST bits simultaneously stops the TIM counter at a value
of $0000.
PS[2:0] — Prescaler Select Bits
These read/write bits select one of the seven prescaler outputs as the input to
the TIM counter as Table 23-2 shows. Reset clears the PS[2:0] bits.
Table 23-2. Prescaler Selection
PS2
PS1
PS0
TIM Clock Source
0
0
0
Internal bus clock ÷ 1
0
0
1
Internal bus clock ÷ 2
0
1
0
Internal bus clock ÷ 4
0
1
1
Internal bus clock ÷ 8
1
0
0
Internal bus clock ÷ 16
1
0
1
Internal bus clock ÷ 32
1
1
0
Internal bus clock ÷ 64
1
1
1
Not available
Data Sheet
316
MC68HC908GZ8
Timer Interface Module (TIM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Timer Interface Module (TIM)
I/O Registers
23.9.2 TIM Counter Registers
The two read-only TIM counter registers contain the high and low bytes of the value
in the TIM counter. Reading the high byte (TCNTH) latches the contents of the low
byte (TCNTL) into a buffer. Subsequent reads of TCNTH do not affect the latched
TCNTL value until TCNTL is read. Reset clears the TIM counter registers. Setting
the TIM reset bit (TRST) also clears the TIM counter registers.
Freescale Semiconductor, Inc...
NOTE:
If you read TCNTH during a break interrupt, be sure to unlatch TCNTL by reading
TCNTL before exiting the break interrupt. Otherwise, TCNTL retains the value
latched during the break.
Address: T1CNTH, $0021 and T2CNTH, $002C
Read:
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
0
0
0
0
0
0
0
Write:
Reset:
0
= Unimplemented
Figure 23-5. TIM Counter Registers High (TCNTH)
Address: T1CNTL, $0022 and T2CNTL, $002D
Read:
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
Write:
Reset:
0
= Unimplemented
Figure 23-6. TIM Counter Registers Low (TCNTL)
23.9.3 TIM Counter Modulo Registers
The read/write TIM modulo registers contain the modulo value for the TIM counter.
When the TIM counter reaches the modulo value, the overflow flag (TOF) becomes
set, and the TIM counter resumes counting from $0000 at the next timer clock.
Writing to the high byte (TMODH) inhibits the TOF bit and overflow interrupts until
the low byte (TMODL) is written. Reset sets the TIM counter modulo registers.
Address: T1MODH, $0023 and T2MODH, $002E
Read:
Write:
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
1
1
1
1
1
1
1
1
Figure 23-7. TIM Counter Modulo Register High (TMODH)
MC68HC908GZ8
MOTOROLA
Data Sheet
Timer Interface Module (TIM)
For More Information On This Product,
Go to: www.freescale.com
317
Freescale Semiconductor, Inc.
Timer Interface Module (TIM)
Address: T1MODL, $0024 and T2MODL, $002F
Read:
Write:
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
6
5
4
3
2
1
Bit 0
1
1
1
1
1
1
1
1
Figure 23-8. TIM Counter Modulo Register Low (TMODL)
NOTE:
Reset the TIM counter before writing to the TIM counter modulo registers.
Freescale Semiconductor, Inc...
23.9.4 TIM Channel Status and Control Registers
Each of the TIM channel status and control registers:
•
Flags input captures and output compares
•
Enables input capture and output compare interrupts
•
Selects input capture, output compare, or PWM operation
•
Selects high, low, or toggling output on output compare
•
Selects rising edge, falling edge, or any edge as the active input capture
trigger
•
Selects output toggling on TIM overflow
•
Selects 0% and 100% PWM duty cycle
•
Selects buffered or unbuffered output compare/PWM operation
Address: T1SC0, $0025 and T2SC0, $0030
Bit 7
Read:
CH0F
Write:
0
Reset:
0
6
5
4
3
2
1
Bit 0
CH0IE
MS0B
MS0A
ELS0B
ELS0A
TOV0
CH0MAX
0
0
0
0
0
0
0
Figure 23-9. TIM Channel 0 Status and Control Register (TSC0)
Address: T1SC1, $0028 and T2SC1, $0033
Bit 7
Read:
CH1F
Write:
0
Reset:
0
6
CH1IE
0
5
0
0
4
3
2
1
Bit 0
MS1A
ELS1B
ELS1A
TOV1
CH1MAX
0
0
0
0
0
Figure 23-10. TIM Channel 1 Status and Control Register (TSC1)
CHxF — Channel x Flag Bit
When channel x is an input capture channel, this read/write bit is set when an
active edge occurs on the channel x pin. When channel x is an output compare
channel, CHxF is set when the value in the TIM counter registers matches the
value in the TIM channel x registers.
Data Sheet
318
MC68HC908GZ8
Timer Interface Module (TIM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Timer Interface Module (TIM)
I/O Registers
When TIM CPU interrupt requests are enabled (CHxIE = 1), clear CHxF by
reading TIM channel x status and control register with CHxF set and then writing
a logic 0 to CHxF. If another interrupt request occurs before the clearing
sequence is complete, then writing logic 0 to CHxF has no effect. Therefore, an
interrupt request cannot be lost due to inadvertent clearing of CHxF.
Reset clears the CHxF bit. Writing a logic 1 to CHxF has no effect.
1 = Input capture or output compare on channel x
0 = No input capture or output compare on channel x
Freescale Semiconductor, Inc...
CHxIE — Channel x Interrupt Enable Bit
This read/write bit enables TIM CPU interrupt service requests on channel x.
Reset clears the CHxIE bit.
1 = Channel x CPU interrupt requests enabled
0 = Channel x CPU interrupt requests disabled
MSxB — Mode Select Bit B
This read/write bit selects buffered output compare/PWM operation. MSxB
exists only in the TIM1 channel 0 and TIM2 channel 0 status and control
registers.
Setting MS0B disables the channel 1 status and control register and reverts
TCH1 to general-purpose I/O.
Reset clears the MSxB bit.
1 = Buffered output compare/PWM operation enabled
0 = Buffered output compare/PWM operation disabled
MSxA — Mode Select Bit A
When ELSxB:A ≠ 00, this read/write bit selects either input capture operation or
unbuffered output compare/PWM operation.
See Table 23-3.
1 = Unbuffered output compare/PWM operation
0 = Input capture operation
When ELSxB:A = 00, this read/write bit selects the initial output level of the
TCHx pin. See Table 23-3.
Reset clears the MSxA bit.
1 = Initial output level low
0 = Initial output level high
NOTE:
Before changing a channel function by writing to the MSxB or MSxA bit, set the
TSTOP and TRST bits in the TIM status and control register (TSC).
ELSxB and ELSxA — Edge/Level Select Bits
When channel x is an input capture channel, these read/write bits control the
active edge-sensing logic on channel x.
When channel x is an output compare channel, ELSxB and ELSxA control the
channel x output behavior when an output compare occurs.
When ELSxB and ELSxA are both clear, channel x is not connected to port D,
and pin PTDx/TCHx is available as a general-purpose I/O pin. Table 23-3
shows how ELSxB and ELSxA work. Reset clears the ELSxB and ELSxA bits.
MC68HC908GZ8
MOTOROLA
Data Sheet
Timer Interface Module (TIM)
For More Information On This Product,
Go to: www.freescale.com
319
Freescale Semiconductor, Inc.
Timer Interface Module (TIM)
Table 23-3. Mode, Edge, and Level Selection
MSxB:MSxA
ELSxB:ELSxA
X0
00
Mode
Freescale Semiconductor, Inc...
Output
preset
NOTE:
Configuration
Pin under port control;
initial output level high
X1
00
Pin under port control;
initial output level low
00
01
Capture on rising edge only
00
10
00
11
01
01
01
10
01
11
1X
01
1X
10
1X
11
Input
capture
Capture on falling edge only
Capture on rising or
falling edge
Toggle output on compare
Output compare
or PWM
Clear output on compare
Set output on compare
Buffered output
compare
or buffered
PWM
Toggle output on compare
Clear output on compare
Set output on compare
Before enabling a TIM channel register for input capture operation, make sure that
the PTD/TCHx pin is stable for at least two bus clocks.
TOVx — Toggle On Overflow Bit
When channel x is an output compare channel, this read/write bit controls the
behavior of the channel x output when the TIM counter overflows. When
channel x is an input capture channel, TOVx has no effect.
Reset clears the TOVx bit.
1 = Channel x pin toggles on TIM counter overflow.
0 = Channel x pin does not toggle on TIM counter overflow.
NOTE:
When TOVx is set, a TIM counter overflow takes precedence over a channel x
output compare if both occur at the same time.
CHxMAX — Channel x Maximum Duty Cycle Bit
When the TOVx bit is at logic 1, setting the CHxMAX bit forces the duty cycle of
buffered and unbuffered PWM signals to 100%. As Figure 23-11 shows, the
CHxMAX bit takes effect in the cycle after it is set or cleared. The output stays
at the 100% duty cycle level until the cycle after CHxMAX is cleared.
Data Sheet
320
MC68HC908GZ8
Timer Interface Module (TIM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Timer Interface Module (TIM)
I/O Registers
OVERFLOW
OVERFLOW
OVERFLOW
OVERFLOW
OVERFLOW
PERIOD
TCHx
OUTPUT
COMPARE
OUTPUT
COMPARE
OUTPUT
COMPARE
OUTPUT
COMPARE
CHxMAX
Freescale Semiconductor, Inc...
Figure 23-11. CHxMAX Latency
23.9.5 TIM Channel Registers
These read/write registers contain the captured TIM counter value of the input
capture function or the output compare value of the output compare function. The
state of the TIM channel registers after reset is unknown.
In input capture mode (MSxB:MSxA = 0:0), reading the high byte of the TIM
channel x registers (TCHxH) inhibits input captures until the low byte (TCHxL) is
read.
In output compare mode (MSxB:MSxA ≠ 0:0), writing to the high byte of the TIM
channel x registers (TCHxH) inhibits output compares until the low byte (TCHxL) is
written.
Address: T1CH0H, $0026 and T2CH0H, $0031
Read:
Write:
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
Reset:
Indeterminate after reset
Figure 23-12. TIM Channel 0 Register High (TCH0H)
Address: T1CH0L, $0027 and T2CH0L $0032
Read:
Write:
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
6
5
4
3
2
1
Bit 0
Indeterminate after reset
Figure 23-13. TIM Channel 0 Register Low (TCH0L)
MC68HC908GZ8
MOTOROLA
Data Sheet
Timer Interface Module (TIM)
For More Information On This Product,
Go to: www.freescale.com
321
Freescale Semiconductor, Inc.
Timer Interface Module (TIM)
Address: T1CH1H, $0029 and T2CH1H, $0034
Read:
Write:
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
Reset:
Indeterminate after reset
Figure 23-14. TIM Channel 1 Register High (TCH1H)
Address: T1CH1L, $002A and T2CH1L, $0035
Freescale Semiconductor, Inc...
Read:
Write:
Reset:
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
6
5
4
3
2
1
Bit 0
Indeterminate after reset
Figure 23-15. TIM Channel 1 Register Low (TCH1L)
Data Sheet
322
MC68HC908GZ8
Timer Interface Module (TIM)
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 24. Electrical Specifications
24.1 Introduction
Freescale Semiconductor, Inc...
This section contains electrical and timing specifications.
24.2 Absolute Maximum Ratings
Maximum ratings are the extreme limits to which the MCU can be exposed without
permanently damaging it.
NOTE:
This device is not guaranteed to operate properly at the maximum ratings. Refer to
24.5 5-Vdc Electrical Characteristics and 24.6 3.3-Vdc Electrical
Characteristics for guaranteed operating conditions.
Characteristic(1)
Symbol
Value
Unit
Supply voltage
VDD
–0.3 to + 6.0
V
Input voltage
VIn
VSS – 0.3 to VDD + 0.3
V
I
± 15
mA
Maximum current for pins
PTC0–PTC4
IPTC0–PTC4
± 25
mA
Maximum current into VDD
Imvdd
150
mA
Maximum current out of VSS
Imvss
150
mA
Storage temperature
Tstg
–55 to +150
°C
Maximum current per pin
excluding those specified below
1. Voltages referenced to VSS
NOTE:
This device contains circuitry to protect the inputs against damage due to high
static voltages or electric fields; however, it is advised that normal precautions be
taken to avoid application of any voltage higher than maximum-rated voltages to
this high-impedance circuit. For proper operation, it is recommended that VIn and
VOut be constrained to the range VSS ≤ (VIn or VOut) ≤ VDD. Reliability of operation
is enhanced if unused inputs are connected to an appropriate logic voltage level
(for example, either VSS or VDD).
MC68HC908GZ8
MOTOROLA
Data Sheet
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
323
Freescale Semiconductor, Inc.
Electrical Specifications
24.3 Functional Operating Range
Characteristic
Symbol
Value
Unit
TA
–40 to +125
°C
VDD
5.0 ±10%
3.3 ±10%
V
Operating temperature range
Operating voltage range
24.4 Thermal Characteristics
Freescale Semiconductor, Inc...
Characteristic
Symbol
Value
Unit
Thermal resistance
32-pin LQFP
48-pin LQFP
θJA
95
95
°C/W
I/O pin power dissipation
PI/O
User determined
W
Power dissipation(1)
PD
PD = (IDD × VDD) + PI/O =
K/(TJ + 273 °C)
W
Constant(2)
K
Average junction temperature
TJ
PD × (TA + 273 °C)
+ PD2 × θJA
W/°C
TA + (PD × θJA)
°C
1. Power dissipation is a function of temperature.
2. K is a constant unique to the device. K can be determined for a known TA and measured PD.
With this value of K, PD and TJ can be determined for any value
of TA.
Data Sheet
324
MC68HC908GZ8
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Electrical Specifications
5-Vdc Electrical Characteristics
24.5 5-Vdc Electrical Characteristics
Symbol
Min
Typ(2)
Max
Unit
VOH
VOH
VOH
IOH1
VDD – 0.8
VDD – 1.5
VDD – 1.5
—
—
—
—
—
—
—
V
V
V
—
50
mA
IOH2
—
—
50
mA
IOHT
—
—
100
mA
VOL
VOL
VOL
IOL1
—
—
—
—
—
—
0.4
1.5
1.5
V
V
V
—
—
50
mA
IOL2
—
—
50
mA
IOLT
—
—
100
mA
Input high voltage
All ports, IRQ, RST, OSC1
VIH
0.7 × VDD
—
VDD
V
Input low voltage
All ports, IRQ, RST, OSC1
VIL
VSS
—
0.2 × VDD
V
—
—
20
6
30
12
mA
mA
—
—
—
—
—
3
20
300
50
500
—
—
—
—
—
µA
µA
µA
µA
µA
Freescale Semiconductor, Inc...
Characteristic(1)
Output high voltage
(ILoad = –2.0 mA) all I/O pins
(ILoad = –10.0 mA) all I/O pins
(ILoad = –20.0 mA) pins PTC0–PTC4 only
Maximum combined IOH for port PTA7–PTA3,
port PTC0–PTC1, port E, port PTD0–PTD3
Maximum combined IOH for port PTA2–PTA0,
port B, port PTC2–PTC6, port PTD4–PTD7
Maximum total IOH for all port pins
Output low voltage
(ILoad = 1.6 mA) all I/O pins
(ILoad = 10 mA) all I/O pins
(ILoad = 20mA) pins PTC0–PTC4 only
Maximum combined IOH for port PTA7–PTA3,
port PTC0–PTC1, port E, port PTD0–PTD3
Maximum combined IOH for port PTA2–PTA0,
port B, port PTC2–PTC6, port PTD4–PTD7
Maximum total IOL for all port pins
VDD supply current
Run(3)
Wait(4)
Stop(5)
25°C
25°C with TBM enabled(6)
25°C with LVI and TBM enabled(6)
–40°C to 125°C with TBM enabled(6)
–40°C to 125°C with LVI and TBM enabled(6)
IDD
I/O ports Hi-Z leakage current(7)
IIL
–10
—
+10
µA
Input current
IIn
—1
—
+1
µA
RPU
20
45
65
kΩ
Pullup resistors (as input only)
Ports PTA7/KBD7–PTA0/KBD0,
PTD7/T2CH1–PTD0/SS
PTC6–PTC0/CANTX,
Continued on next page
MC68HC908GZ8
MOTOROLA
Data Sheet
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
325
Freescale Semiconductor, Inc.
Electrical Specifications
Symbol
Min
Typ(2)
Max
Unit
Capacitance
Ports (as input or output)
COut
CIn
—
—
—
—
12
8
pF
Monitor mode entry voltage
VTST
VDD + 2.5
—
VDD + 4.0
V
Low-voltage inhibit, trip falling voltage
VTRIPF
3.90
4.25
4.50
V
Low-voltage inhibit, trip rising voltage
VTRIPR
4.20
4.35
4.60
V
Low-voltage inhibit reset/recover hysteresis
(VTRIPF + VHYS = VTRIPR)
VHYS
—
100
—
mV
POR rearm voltage(8)
VPOR
0
—
100
mV
POR reset voltage(9)
VPORRST
0
700
800
mV
RPOR
0.035
—
—
V/ms
Freescale Semiconductor, Inc...
Characteristic(1)
POR rise time ramp rate(10)
1. VDD = 5.0 Vdc ± 10%, VSS = 0 Vdc, TA = TA (min) to TA (max), unless otherwise noted
2. Typical values reflect average measurements at midpoint of voltage range, 25°C only.
3. Run (operating) IDD measured using external square wave clock source (fOSC = 32 MHz). All inputs 0.2 V from rail. No dc
loads. Less than 100 pF on all outputs. CL = 20 pF on OSC2. All ports configured as inputs. OSC2 capacitance linearly
affects run IDD. Measured with all modules enabled.
4. Wait IDD measured using external square wave clock source (fOSC = 32 MHz). All inputs 0.2 V from rail. No dc loads. Less
than 100 pF on all outputs. CL = 20 pF on OSC2. All ports configured as inputs. OSC2 capacitance linearly affects wait
IDD. Measured with ICG and LVI enabled.
5. Stop IDD is measured with OSC1 = VSS. All inputs 0.2 V from rail. No dc loads. Less than 100 pF on all outputs. All ports
configured as inputs. Typical values at midpoint of voltage range, 25°C only.
6. Stop IDD with TBM enabled is measured using an external square wave clock source (fOSC = 32 MHz). All inputs 0.2 V
from rail. No dc loads. Less than 100 pF on all outputs. All inputs configured as inputs.
7. Pullups and pulldowns are disabled. Port B leakage is specified in 24.10 5.0-Volt ADC Characteristics.
8. Maximum is highest voltage that POR is guaranteed.
9. Maximum is highest voltage that POR is possible.
10. If minimum VDD is not reached before the internal POR reset is released, RST must be driven low externally until minimum
VDD is reached.
Data Sheet
326
MC68HC908GZ8
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Electrical Specifications
3.3-Vdc Electrical Characteristics
24.6 3.3-Vdc Electrical Characteristics
Symbol
Min
Typ(2)
Max
Unit
VOH
VOH
VOH
IOH1
VDD – 0.3
VDD – 1.0
VDD – 1.0
—
—
—
—
—
—
—
V
V
V
—
30
mA
IOH2
—
—
30
mA
IOHT
—
—
60
mA
VOL
VOL
VOL
IOL1
—
—
—
—
—
—
0.3
1.0
0.8
V
V
V
—
—
30
mA
IOL2
—
—
30
mA
IOLT
—
—
60
mA
Input high voltage
All ports, IRQ, RST, OSC1
VIH
0.7 × VDD
—
VDD
V
Input low voltage
All ports, IRQ, RST, OSC1
VIL
VSS
—
0.3 × VDD
V
—
—
8
3
12
6
mA
mA
—
—
—
—
—
2
12
200
30
300
—
—
—
—
—
µA
µA
µA
µA
µA
Freescale Semiconductor, Inc...
Characteristic(1)
Output high voltage
(ILoad = –0.6 mA) all I/O pins
(ILoad = –4.0 mA) all I/O pins
(ILoad = –10.0 mA) pins PTC0–PTC4 only
Maximum combined IOH for port PTA7–PTA3,
port PTC0–PTC1, port E, port PTD0–PTD3
Maximum combined IOH for port PTA2–PTA0,
port B, port PTC2–PTC6, port PTD4–PTD7
Maximum total IOH for all port pins
Output low voltage
(ILoad = 1.6 mA) all I/O pins
(ILoad = 10 mA) all I/O pins
(ILoad = 20 mA) pins PTC0–PTC4 only
Maximum combined IOH for port PTA7–PTA3,
port PTC0–PTC1, port E, port PTD0–PTD3
Maximum combined IOH for port PTA2–PTA0,
port B, port PTC2–PTC6, port PTD4–PTD7
Maximum total IOL for all port pins
VDD supply current
Run(3)
Wait(4)
Stop(5)
25°C
25°C with TBM enabled(6)
25°C with LVI and TBM enabled(6)
–40°C to 125°C with TBM enabled(6)
–40°C to 125°C with LVI and TBM enabled(6)
IDD
I/O ports Hi-Z leakage current(7)
IIL
–10
—
+10
µA
Input current
IIn
—1
—
+1
µA
RPU
20
45
65
kΩ
Pullup resistors (as input only)
Ports PTA7/KBD7–PTA0/KBD0, PTC6–PTC0,
PTD7/T2CH1–PTD0/SS
Continued on next page
MC68HC908GZ8
MOTOROLA
Data Sheet
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
327
Freescale Semiconductor, Inc.
Electrical Specifications
Symbol
Min
Typ(2)
Max
Unit
Capacitance
Ports (as input or output)
COut
CIn
—
—
—
—
12
8
pF
Monitor mode entry voltage
VTST
VDD + 2.5
—
VDD + 4.0
V
Low-voltage inhibit, trip falling voltage
VTRIPF
2.35
2.6
2.7
V
Low-voltage inhibit, trip rising voltage
VTRIPR
2.4
2.66
2.8
V
Low-voltage inhibit reset/recover hysteresis
(VTRIPF + VHYS = VTRIPR)
VHYS
—
100
—
mV
POR rearm voltage(8)
VPOR
0
—
100
mV
POR reset voltage(9)
VPORRST
0
700
800
mV
RPOR
0.02
—
—
V/ms
Freescale Semiconductor, Inc...
Characteristic(1)
POR rise time ramp rate(10)
1. VDD = 3.3 Vdc ± 10%, VSS = 0 Vdc, TA = TA (min) to TA (max), unless otherwise noted
2. Typical values reflect average measurements at midpoint of voltage range, 25°C only.
3. Run (operating) IDD measured using external square wave clock source (fOSC = 16 MHz). All inputs 0.2 V from rail. No dc
loads. Less than 100 pF on all outputs. CL = 20 pF on OSC2. All ports configured as inputs. OSC2 capacitance linearly
affects run IDD. Measured with all modules enabled.
4. Wait IDD measured using external square wave clock source (fOSC = 16 MHz). All inputs 0.2 V from rail. No dc loads. Less
than 100 pF on all outputs. CL = 20 pF on OSC2. All ports configured as inputs. OSC2 capacitance linearly affects wait
IDD. Measured with ICG and LVI enabled.
5. Stop IDD is measured with OSC1 = VSS. All inputs 0.2 V from rail. No dc loads. Less than 100 pF on all outputs. All ports
configured as inputs. Typical values at midpoint of voltage range, 25°C only.
6. Stop IDD with TBM enabled is measured using an external square wave clock source (fOSC = 16 MHz). All inputs 0.2 V
from rail. No dc loads. Less than 100 pF on all outputs. All inputs configured as inputs.
7. Pullups and pulldowns are disabled.
8. Maximum is highest voltage that POR is guaranteed.
9. Maximum is highest voltage that POR is possible.
10. If minimum VDD is not reached before the internal POR reset is released, RST must be driven low externally until minimum
VDD is reached.
Data Sheet
328
MC68HC908GZ8
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Electrical Specifications
5.0-Volt Control Timing
24.7 5.0-Volt Control Timing
Symbol
Min
Max
Unit
fOSC
1
dc
8
32
MHz
Internal operating frequency
fOP (fBus)
—
8
MHz
Internal clock period (1/fOP)
tCYC
125
—
ns
RST input pulse width low
tRL
50
—
ns
IRQ interrupt pulse width low (edge-triggered)
tILIH
50
—
ns
IRQ interrupt pulse period
tILIL
Note(3)
—
tCYC
Characteristic(1)
Frequency of operation
Crystal option
Freescale Semiconductor, Inc...
External clock option
(2)
1. VSS = 0 Vdc; timing shown with respect to 20% VDD and 70% VDD unless otherwise noted.
2. No more than 10% duty cycle deviation from 50%.
3. The minimum period is the number of cycles it takes to execute the interrupt service routine plus 1 tCYC.
24.8 3.3-Volt Control Timing
Symbol
Min
Max
Unit
fOSC
1
dc
8
16
MHz
Internal operating frequency
fOP (fBus)
—
4
MHz
Internal clock period (1/fOP)
tCYC
250
—
ns
RST input pulse width low
tRL
125
—
ns
IRQ interrupt pulse width low (edge-triggered)
tILIH
125
—
ns
tILIL
Note(3)
—
tCYC
Characteristic(1)
Frequency of operation
Crystal option
External clock option
(2)
IRQ interrupt pulse period
1. VSS = 0 Vdc; timing shown with respect to 20% VDD and 70% VDD unless otherwise noted.
2. No more than 10% duty cycle deviation from 50%.
3. The minimum period is the number of cycles it takes to execute the interrupt service routine plus 1 tCYC.
tRL
RST
tILIL
tILIH
IRQ
Figure 24-1. RST and IRQ Timing
MC68HC908GZ8
MOTOROLA
Data Sheet
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
329
Freescale Semiconductor, Inc.
Electrical Specifications
24.9 Clock Generation Module Characteristics
24.9.1 CGM Component Specifications
Characteristic
Symbol
Min
Typ
Max
Unit
fXCLK
1
4
8
MHz
Crystal load capacitance(1)
CL
—
—
—
pF
Crystal fixed capacitance
C1
—
(2 x CL) –5
—
pF
Crystal tuning capacitance
C2
—
(2 x CL) –5
—
pF
Feedback bias resistor
RB
1
10
20
MΩ
Symbol
Min
Typ
Max
Unit
Reference frequency (for PLL operation)
fRCLK
1
4
8
MHz
Range nominal multiplier
fNOM
—
71.42
—
KHz
Programmed VCO center-of-range frequency(1)
fVRS
—
(Lx2E)fNOM
—
MHz
Freescale Semiconductor, Inc...
Crystal frequency
1. Consult crystal manufacturer’s data.
24.9.2 CGM Electrical Specifications
Characteristic
1. See 7.3.6 Programming the PLL for detailed instruction on selecting appropriate values for L and E.
Data Sheet
330
MC68HC908GZ8
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Electrical Specifications
5.0-Volt ADC Characteristics
24.10 5.0-Volt ADC Characteristics
Freescale Semiconductor, Inc...
Characteristic(1)
Symbol
Min
Max
Unit
Comments
Supply voltage
VDDAD
4.5
5.5
V
VDDAD should be tied to
the same potential as VDD
via separate traces.
Input voltages
VADIN
0
VDDAD
V
VADIN <= VDDAD
Resolution
BAD
10
10
Bits
Absolute accuracy
AAD
–4
+4
Counts
Includes quantization
ADC internal clock
fADIC
500 k
1.048 M
Hz
tAIC = 1/fADIC
Conversion range
RAD
VSSAD
VDDAD
V
Power-up time
tADPU
16
—
tAIC cycles
Conversion time
tADC
16
17
tAIC cycles
Sample time
tADS
5
—
tAIC cycles
Monotonicity
MAD
Zero input reading
ZADI
000
003
Hex
VADIN = VSSA
Full-scale reading
FADI
3FC
3FF
Hex
VADIN = VDDA
Input capacitance
CADI
—
30
pF
Not tested
VDDAD/VREFH current
IVREF
—
1.6
mA
Absolute accuracy
(8-bit truncation mode)
AAD
–1
+1
LSB
Quantization error
(8-bit truncation mode)
—
–1/8
+7/8
LSB
Guaranteed
Includes quantization
1. VDD = 5.0 Vdc ± 10%, VSS = 0 Vdc, VDDAD/VREFH = 5.0 Vdc ± 10%, VSSAD/VREFL = 0 Vdc
MC68HC908GZ8
MOTOROLA
Data Sheet
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
331
Freescale Semiconductor, Inc.
Electrical Specifications
24.11 3.3-Volt ADC Characteristics
Freescale Semiconductor, Inc...
Characteristic(1)
Symbol
Min
Max
Unit
Comments
Supply voltage
VDDAD
3.0
3.6
V
VDDAD should be tied to
the same potential as VDD
via separate traces.
Input voltages
VADIN
0
VDDAD
V
VADIN <= VDDAD
Resolution
BAD
10
10
Bits
Absolute accuracy
AAD
–6
+6
Counts
Includes quantization
ADC internal clock
fADIC
500 k
1.048 M
Hz
tAIC = 1/fADIC
Conversion range
RAD
VSSAD
VDDAD
V
Power-up time
tADPU
16
—
tAIC cycles
Conversion time
tADC
16
17
tAIC cycles
Sample time
tADS
5
—
tAIC cycles
Monotonicity
MAD
Zero input reading
ZADI
000
005
Hex
VADIN = VSSA
Full-scale reading
FADI
3FA
3FF
Hex
VADIN = VDDA
Input capacitance
CADI
—
30
pF
Not tested
VDDAD/VREFH current
IVREF
—
1.2
mA
Absolute accuracy
(8-bit truncation mode)
AAD
–1
+1
LSB
Quantization error
(8-bit truncation mode)
—
–1/8
+7/8
LSB
Guaranteed
Includes quantization
1. VDD = 3.3 Vdc ± 10%, VSS = 0 Vdc, VDDAD/VREFH = 3.3 Vdc ± 10%, VSSAD/VREFL = 0 Vdc
Data Sheet
332
MC68HC908GZ8
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Electrical Specifications
5.0-Volt SPI Characteristics
24.12 5.0-Volt SPI Characteristics
Freescale Semiconductor, Inc...
Diagram
Number(1)
Characteristic(2)
Symbol
Min
Max
Unit
Operating frequency
Master
Slave
fOP(M)
fOP(S)
fOP/128
dc
fOP/2
fOP
MHz
MHz
1
Cycle time
Master
Slave
tCYC(M)
tCYC(S)
2
1
128
—
tCYC
tCYC
2
Enable lead time
tLead(S)
1
—
tCYC
3
Enable lag time
tLag(S)
1
—
tCYC
4
Clock (SPSCK) high time
Master
Slave
tSCKH(M)
tSCKH(S)
tCYC –25
1/2 tCYC –25
64 tCYC
—
ns
ns
5
Clock (SPSCK) low time
Master
Slave
tSCKL(M)
tSCKL(S)
tCYC –25
1/2 tCYC –25
64 tCYC
—
ns
ns
6
Data setup time (inputs)
Master
Slave
tSU(M)
tSU(S)
30
30
—
—
ns
ns
7
Data hold time (inputs)
Master
Slave
tH(M)
tH(S)
30
30
—
—
ns
ns
8
Access time, slave(3)
CPHA = 0
CPHA = 1
tA(CP0)
tA(CP1)
0
0
40
40
ns
ns
9
Disable time, slave(4)
tDIS(S)
—
40
ns
10
Data valid time, after enable edge
Master
Slave(5)
tV(M)
tV(S)
—
—
50
50
ns
ns
11
Data hold time, outputs, after enable edge
Master
Slave
tHO(M)
tHO(S)
0
0
—
—
ns
ns
1. Numbers refer to dimensions in Figure 24-2 and Figure 24-3.
2. All timing is shown with respect to 20% VDD and 70% VDD, unless noted; 100 pF load on all SPI pins.
3. Time to data active from high-impedance state
4. Hold time to high-impedance state
5. With 100 pF on all SPI pins
MC68HC908GZ8
MOTOROLA
Data Sheet
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
333
Freescale Semiconductor, Inc.
Electrical Specifications
24.13 3.3-Volt SPI Characteristics
Freescale Semiconductor, Inc...
Diagram
Number(1)
Characteristic(2)
Symbol
Min
Max
Unit
Operating frequency
Master
Slave
fOP(M)
fOP(S)
fOP/128
DC
fOP/2
fOP
MHz
MHz
1
Cycle time
Master
Slave
tCYC(M)
tCYC(S)
2
1
128
—
tcyc
tcyc
2
Enable lead time
tLead(S)
1
—
tcyc
3
Enable lag time
tLag(S)
1
—
tcyc
4
Clock (SPSCK) high time
Master
Slave
tSCKH(M)
tSCKH(S)
tcyc –35
1/2 tcyc –35
64 tcyc
—
ns
ns
5
Clock (SPSCK) low time
Master
Slave
tSCKL(M)
tSCKL(S)
tcyc –35
1/2 tcyc –35
±
64 tcyc
—
ns
ns
6
Data setup time (inputs)
Master
Slave
tSU(M)
tSU(S)
40
40
—
—
ns
ns
7
Data hold time (inputs)
Master
Slave
tH(M)
tH(S)
40
40
—
—
ns
ns
8
Access time, slave(3)
CPHA = 0
CPHA = 1
tA(CP0)
tA(CP1)
0
0
50
50
ns
ns
9
Disable time, slave(4)
tDIS(S)
—
50
ns
10
Data valid time, after enable edge
Master
Slave(5)
tV(M)
tV(S)
—
—
60
60
ns
ns
11
Data hold time, outputs, after enable edge
Master
Slave
tHO(M)
tHO(S)
0
0
—
—
ns
ns
1. Numbers refer to dimensions in Figure 24-2 and Figure 24-3.
2. All timing is shown with respect to 20% VDD and 70% VDD, unless noted; 100 pF load on all SPI pins.
3. Time to data active from high-impedance state
4. Hold time to high-impedance state
5. With 100 pF on all SPI pins
Data Sheet
334
MC68HC908GZ8
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Electrical Specifications
3.3-Volt SPI Characteristics
SS
INPUT
SS PIN OF MASTER HELD HIGH
1
SPSCK OUTPUT
CPOL = 0
NOTE
SPSCK OUTPUT
CPOL = 1
NOTE
5
4
5
4
6
Freescale Semiconductor, Inc...
MISO
INPUT
MSB IN
BITS 6–1
11
MOSI
OUTPUT
MASTER MSB OUT
7
LSB IN
10
11
BITS 6–1
MASTER LSB OUT
Note: This first clock edge is generated internally, but is not seen at the SPSCK pin.
a) SPI Master Timing (CPHA = 0)
SS
INPUT
SS PIN OF MASTER HELD HIGH
1
SPSCK OUTPUT
CPOL = 0
5
NOTE
4
SPSCK OUTPUT
CPOL = 1
5
NOTE
4
6
MISO
INPUT
MSB IN
10
MOSI
OUTPUT
BITS 6–1
11
MASTER MSB OUT
7
LSB IN
10
BITS 6–1
MASTER LSB OUT
Note: This last clock edge is generated internally, but is not seen at the SPSCK pin.
b) SPI Master Timing (CPHA = 1)
Figure 24-2. SPI Master Timing
MC68HC908GZ8
MOTOROLA
Data Sheet
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
335
Freescale Semiconductor, Inc.
Electrical Specifications
SS
INPUT
3
1
SPSCK INPUT
CPOL = 0
5
4
2
SPSCK INPUT
CPOL = 1
5
4
9
8
Freescale Semiconductor, Inc...
MISO
INPUT
SLAVE
MSB OUT
6
MOSI
OUTPUT
BITS 6–1
7
NOTE
11
11
10
MSB IN
SLAVE LSB OUT
BITS 6–1
LSB IN
Note: Not defined but normally MSB of character just received
a) SPI Slave Timing (CPHA = 0)
SS
INPUT
1
SPSCK INPUT
CPOL = 0
5
4
2
3
SPSCK INPUT
CPOL = 1
8
MISO
OUTPUT
MOSI
INPUT
5
4
10
NOTE
9
SLAVE
MSB OUT
6
7
BITS 6–1
SLAVE LSB OUT
11
10
BITS 6–1
MSB IN
LSB IN
Note: Not defined but normally LSB of character previously transmitted
b) SPI Slave Timing (CPHA = 1)
Figure 24-3. SPI Slave Timing
Data Sheet
336
MC68HC908GZ8
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Electrical Specifications
Timer Interface Module Characteristics
24.14 Timer Interface Module Characteristics
Characteristic
Symbol
tTH, tTL
Timer input capture pulse width
2
(1)
tTLTL
Timer Input capture period
Min
Note
Max
Unit
—
tCYC
—
tCYC
1. The minimum period is the number of cycles it takes to execute the interrupt service routine plus 1 tCYC.
tTLTL
tTH
Freescale Semiconductor, Inc...
INPUT CAPTURE
RISING EDGE
tTLTL
tTL
INPUT CAPTURE
FALLING EDGE
tTLTL
tTH
tTL
INPUT CAPTURE
BOTH EDGES
Figure 24-4. Input Capture Timing
MC68HC908GZ8
MOTOROLA
Data Sheet
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
337
Freescale Semiconductor, Inc.
Electrical Specifications
24.15 Memory Characteristics
Characteristic
Symbol
Min
Max
Unit
VRDR
1.3
—
V
—
1
—
MHz
fRead(1)
dc
8M
Hz
FLASH page erase time
< 1K cycles
> 1K cycles
tErase
1
4
—
—
ms
FLASH mass erase time
tMErase
4
—
ms
FLASH PGM/ERASE to HVEN set up time
tnvs
10
—
µs
FLASH high-voltage hold time
tnvh
5
—
µs
FLASH high-voltage hold time (mass erase)
tnvhl
100
—
µs
FLASH program hold time
tpgs
5
—
µs
FLASH program time
tPROG
30
40
µs
FLASH return to read time
trcv(2)
1
—
µs
FLASH cumulative program HV period
tHV(3)
—
4
ms
FLASH endurance
—
10k
—
Cycles
FLASH data retention time
—
10
—
Years
RAM data retention voltage
FLASH program bus clock frequency
Freescale Semiconductor, Inc...
FLASH read bus clock frequency
1. fRead is defined as the frequency range for which the FLASH memory can be read.
2. trcv is defined as the time it needs before the FLASH can be read after turning off the high voltage charge pump, by clearing
HVEN to logic 0.
3. tHV is defined as the cumulative high voltage programming time to the same row before next erase.
tHV must satisfy this condition: tnvs + tnvh + tpgs + (tPROG × 64) ≤ tHV max.
Data Sheet
338
MC68HC908GZ8
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Data Sheet — MC68HC908GZ8
Section 25. Ordering Information and Mechanical Specifications
25.1 Introduction
Freescale Semiconductor, Inc...
This section provides ordering information for the MC68HC908GZ8 along with the
dimensions for:
•
32-pin low-profile quad flat pack (case 873A)
•
48-pin low-profile quad flat pack (case 932-03)
The following figures show the latest package drawings at the time of this
publication. To make sure that you have the latest package specifications, contact
your local Motorola Sales Office.
25.2 MC Order Numbers
Table 25-1. MC Order Numbers
MC Order
Number
Operating
Temperature Range
MC68HC908GZ8CFJ
–40°C to +85°C
MC68HC908GZ8VFJ
–40°C to +105°C
MC68HC908GZ8MFJ
–40°C to +125°C
MC68HC908GZ8CFA
–40°C to +85°C
MC68HC908GZ8VFA
–40°C to +105°C
MC68HC908GZ8MFA
–40°C to +125°C
Package
32-pin low-profile
quad flat pack
(LQFP)
48-pin low-profile
quad flat pack
(LQFP)
Temperature designators:
C = –40°C to +85°C
V = –40°C to +105°C
M = –40°C to +125°C
MC68HC908GZ8
MOTOROLA
Data Sheet
Ordering Information and Mechanical Specifications
For More Information On This Product,
Go to: www.freescale.com
339
Freescale Semiconductor, Inc.
Ordering Information and Mechanical Specifications
A
–T–, –U–, –Z–
25.3 32-Pin Low-Profile Quad Flat Pack (LQFP)
4X
A1
32
0.20 (0.008) AB T–U Z
25
1
–U–
–T–
B
V
AE
P
B1
DETAIL Y
17
Freescale Semiconductor, Inc...
8
V1
AE
DETAIL Y
9
4X
–Z–
9
0.20 (0.008) AC T–U Z
S1
S
DETAIL AD
G
–AB–
0.10 (0.004) AC
AC T–U Z
–AC–
BASE
METAL
ÉÉ
ÉÉ
ÉÉ
ÉÉ
F
8X
M_
R
J
M
N
D
0.20 (0.008)
SEATING
PLANE
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DATUM PLANE –AB– IS LOCATED AT BOTTOM
OF LEAD AND IS COINCIDENT WITH THE LEAD
WHERE THE LEAD EXITS THE PLASTIC BODY AT
THE BOTTOM OF THE PARTING LINE.
4. DATUMS –T–, –U–, AND –Z– TO BE DETERMINED
AT DATUM PLANE –AB–.
5. DIMENSIONS S AND V TO BE DETERMINED AT
SEATING PLANE –AC–.
6. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE PROTRUSION IS
0.250 (0.010) PER SIDE. DIMENSIONS A AND B
DO INCLUDE MOLD MISMATCH AND ARE
DETERMINED AT DATUM PLANE –AB–.
7. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. DAMBAR PROTRUSION SHALL
NOT CAUSE THE D DIMENSION TO EXCEED
0.520 (0.020).
8. MINIMUM SOLDER PLATE THICKNESS SHALL BE
0.0076 (0.0003).
9. EXACT SHAPE OF EACH CORNER MAY VARY
FROM DEPICTION.
SECTION AE–AE
W
K
X
DETAIL AD
Q_
GAUGE PLANE
H
0.250 (0.010)
C E
DIM
A
A1
B
B1
C
D
E
F
G
H
J
K
M
N
P
Q
R
S
S1
V
V1
W
X
Data Sheet
340
MILLIMETERS
MIN
MAX
7.000 BSC
3.500 BSC
7.000 BSC
3.500 BSC
1.400
1.600
0.300
0.450
1.350
1.450
0.300
0.400
0.800 BSC
0.050
0.150
0.090
0.200
0.500
0.700
12_ REF
0.090
0.160
0.400 BSC
1_
5_
0.150
0.250
9.000 BSC
4.500 BSC
9.000 BSC
4.500 BSC
0.200 REF
1.000 REF
INCHES
MIN
MAX
0.276 BSC
0.138 BSC
0.276 BSC
0.138 BSC
0.055
0.063
0.012
0.018
0.053
0.057
0.012
0.016
0.031 BSC
0.002
0.006
0.004
0.008
0.020
0.028
12_ REF
0.004
0.006
0.016 BSC
1_
5_
0.006
0.010
0.354 BSC
0.177 BSC
0.354 BSC
0.177 BSC
0.008 REF
0.039 REF
MC68HC908GZ8
Ordering Information and Mechanical Specifications
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Ordering Information and Mechanical Specifications
48-Pin Low-Profile Quad Flat Pack (LQFP)
25.4 48-Pin Low-Profile Quad Flat Pack (LQFP)
4X
0.200 AB T-U Z
DETAIL Y
A
P
A1
48
37
1
36
U
V
B
AE
B1
12
25
13
AE
V1
24
DIM
A
A1
B
B1
C
D
E
F
G
H
J
K
L
M
N
P
R
S
S1
V
V1
W
AA
Z
S1
T, U, Z
S
DETAIL Y
4X
0.200 AC T-U Z
0.080 AC
G
AB
AD
AC
MILLIMETERS
MIN
MAX
7.000 BSC
3.500 BSC
7.000 BSC
3.500 BSC
1.400
1.600
0.170
0.270
1.350
1.450
0.170
0.230
0.500 BSC
0.050
0.150
0.090
0.200
0.500
0.700
0 ×
7×
12 ×REF
0.090
0.160
0.250 BSC
0.150
0.250
9.000 BSC
4.500 BSC
9.000 BSC
4.500 BSC
0.200 REF
1.000 REF
M°
BASE METAL
TOP & BOTTOM
N
R
J
0.250
Freescale Semiconductor, Inc...
T
C
E
GAUGE PLANE
9
NOTES:
1. DIMENSIONING AND TOLERANCING PER ASME
Y14.5M, 1994.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DATUM PLANE AB IS LOCATED AT BOTTOM OF LEAD
AND IS COINCIDENT WITH THE LEAD WHERE THE
LEAD EXITS THE PLASTIC BODY AT THE BOTTOM OF
THE PARTING LINE.
4. DATUMS T, U, AND Z TO BE DETERMINED AT DATUM
PLANE AB.
5. DIMENSIONS S AND V TO BE DETERMINED AT
SEATING PLANE AC.
6. DIMENSIONS A AND B DO NOT INCLUDE MOLD
PROTRUSION. ALLOWABLE PROTRUSION IS 0.250
PER SIDE. DIMENSIONS A AND B DO INCLUDE MOLD
MISMATCH AND ARE DETERMINED AT DATUM PLANE
AB.
7. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. DAMBAR PROTRUSION SHALL NOT
CAUSE THE D DIMENSION TO EXCEED 0.350.
8. MINIMUM SOLDER PLATE THICKNESS SHALL BE
F
D
0.080
M
AC T-U Z
SECTION AE-AE
H
W
L°
K
DETAIL AD
AA
MC68HC908GZ8
MOTOROLA
Data Sheet
Ordering Information and Mechanical Specifications
For More Information On This Product,
Go to: www.freescale.com
341
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Ordering Information and Mechanical Specifications
Data Sheet
342
MC68HC908GZ8
Ordering Information and Mechanical Specifications
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
HOW TO REACH US:
USA/EUROPE/LOCATIONS NOT LISTED:
Motorola Literature Distribution;
P.O. Box 5405, Denver, Colorado 80217
1-303-675-2140 or 1-800-441-2447
JAPAN:
Motorola Japan Ltd.; SPS, Technical Information Center,
3-20-1, Minami-Azabu Minato-ku, Tokyo 106-8573 Japan
81-3-3440-3569
Freescale Semiconductor, Inc...
ASIA/PACIFIC:
Motorola Semiconductors H.K. Ltd.;
Silicon Harbour Centre, 2 Dai King Street,
Tai Po Industrial Estate, Tai Po, N.T., Hong Kong
852-26668334
Information in this document is provided solely to enable system and software
implementers to use Motorola products. There are no express or implied copyright
licenses granted hereunder to design or fabricate any integrated circuits or
integrated circuits based on the information in this document.
TECHNICAL INFORMATION CENTER:
Motorola reserves the right to make changes without further notice to any products
1-800-521-6274
herein. Motorola makes no warranty, representation or guarantee regarding the
suitability of its products for any particular purpose, nor does Motorola assume any
HOME PAGE:
http://motorola.com/semiconductors
liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation consequential or
incidental damages. “Typical” parameters which may be provided in Motorola data
sheets and/or specifications can and do vary in different applications and actual
performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts.
Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as
components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which
the failure of the Motorola product could create a situation where personal injury or
death may occur. Should Buyer purchase or use Motorola products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated
with such unintended or unauthorized use, even if such claim alleges that Motorola
was negligent regarding the design or manufacture of the part.
Motorola and the Stylized M Logo are registered in the U.S. Patent and Trademark
Office. digital dna is a trademark of Motorola, Inc. All other product or service
names are the property of their respective owners. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
© Motorola, Inc. 2003
MC68HC908GZ8/D
Rev. 0
2/2003
For More Information On This Product,
Go to: www.freescale.com