BSI BS62LV4006HI55 Very low power cmos sram 512k x 8 bit Datasheet

Very Low Power CMOS SRAM
512K X 8 bit
BS62LV4006
Pb-Free and Green package materials are compliant to RoHS
n FEATURES
n DESCRIPTION
Ÿ Wide VCC operation voltage : 2.4V ~ 5.5V
Ÿ Very low power consumption :
VCC = 3.0V
Operation current : 30mA (Max.) at 55ns
2mA (Max.) at 1MHz
Standby current : 0.25uA (Typ.) at 25 OC
VCC = 5.0V
Operation current : 70mA (Max.) at 55ns
10mA (Max.) at 1MHz
Standby current : 1.5uA (Typ.) at 25OC
Ÿ High speed access time :
-55
55ns (Max.) at VCC=3.0~5.5V
-70
70ns (Max.) at VCC=2.7~5.5V
Ÿ Automatic power down when chip is deselected
Ÿ Easy expansion with CE and OE options
Ÿ Three state outputs and TTL compatible
Ÿ Fully static operation
Ÿ Data retention supply voltage as low as 1.5V
The BS62LV4006 is a high performance, very low power CMOS
Static Random Access Memory organized as 524,288 by 8 bits and
operates form a wide range of 2.4V to 5.5V supply voltage.
Advanced CMOS technology and circuit techniques provide both
high speed and low power features with typical CMOS standby
current of 0.25uA at 3.0V/25OC and maximum access time of 55ns at
3.0V/85OC.
Easy memory expansion is provided by an active LOW chip enable
(CE), and active LOW output enable (OE) and three-state output
drivers.
The BS62LV4006 has an automatic power down feature, reducing
the power consumption significantly when chip is deselected.
The BS62LV4006 is available in DICE form, JEDEC standard 32 pin
450mil Plastic SOP, 600mil Plastic DIP, 400 mil TSOP II,
8mmx13.4mm STSOP and 8mmx20mm TSOP package.
n POWER CONSUMPTION
POWER DISSIPATION
PRODUCT
FAMILY
STANDBY
OPERATING
TEMPERATURE
VCC=5.0V
BS62LV4006DC
BS62LV4006EC
BS62LV4006HC
BS62LV4006PC
BS62LV4006SC
BS62LV4006STC
BS62LV4006TC
BS62LV4006EI
BS62LV4006HI
BS62LV4006PI
BS62LV4006SI
BS62LV4006STI
BS62LV4006TI
Operating
(ICCSB1, Max)
VCC=3.0V
1MHz
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
9mA
43mA
68mA
1.5mA
18mA
29mA
Industrial
-40OC to +85OC
20uA
4.0uA
10mA
45mA
70mA
2mA
20mA
30mA
•
BS62LV4006EC
BS62LV4006EI
BS62LV4006SC
BS62LV4006SI
BS62LV4006PC
BS62LV4006PI
VCC
A15
A17
WE
A13
A8
A9
A11
OE
A10
CE
DQ7
DQ6
DQ5
DQ4
DQ3
DICE
TSOP II-32
BGA-36-0608
PDIP-32
SOP-32
STSOP-32
TSOP-32
TSOP II-32
BGA-36-0608
PDIP-32
SOP-32
STSOP-32
TSOP-32
n BLOCK DIAGRAM
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
BS62LV4006TC
BS62LV4006TI
BS62LV4006STC
BS62LV4006STI
32
31
30
29
28
27
26
25
24
23
22
21
20
19
18
17
fMax.
2.0uA
1
A18
A16
A14
A12
A7
A6
A5
A4
A3
A2
A1
A0
DQ0
DQ1
DQ2
GND
1MHz
10uA
•
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
fMax.
VCC=3V
10MHz
Commercial
+0OC to +70OC
n PIN CONFIGURATIONS
A11
A9
A8
A13
WE
A17
A15
VCC
A18
A16
A14
A12
A7
A6
A5
A4
PKG TYPE
(ICC, Max)
VCC=5V
10MHz
2
OE
A10
CE
DQ7
DQ6
DQ5
DQ4
DQ3
GND
DQ2
DQ1
DQ0
A0
A1
A2
A3
3
4
A12
A14
A16
A18
A15
A17
A13
A8
A9
A11
Address
10
Input
Decoder
5
A0
A1
NC
A3
A6
A8
B
DQ4
A2
WE
A4
A7
DQ0
DQ5
DQ6
8
8
VSS
NC
A5
Data
Input
Buffer
Data
Output
Buffer
8
Column I/O
Write Driver
Sense Amp
8
256
Column Decoder
DQ7
DQ5
1024 x 4096
Buffer
DQ1
DQ2
6
A
D
Memory Array
4096
DQ0
DQ3
DQ4
C
1024
Row
DQ1
9
CE
VCC
WE
E
VCC
F
DQ6
G
DQ7
H
A9
VSS
A18
A17
OE
CE
A16
A15
DQ3
A10
A11
A12
A13
A14
Control
Address Input Buffer
OE
VCC
DQ2
GND
A7 A6 A5 A4 A3 A2 A1 A0 A0
36-ball BGA top view
Brilliance Semiconductor, Inc. reserves the right to change products and specifications without notice.
R0201-BS62LV4006
1
Revision 1.4
May.
2006
BS62LV4006
n PIN DESCRIPTIONS
Name
Function
A0-A18 Address Input
These 19 address inputs select one of the 524,288 x 8-bit in the RAM
CE Chip Enable Input
CE is active LOW. Chip enable must be active when data read form or write to the
device. If chip enable is not active, the device is deselected and is in standby power
mode. The DQ pins will be in the high impedance state when the device is deselected.
WE Write Enable Input
The write enable input is active LOW and controls read and write operations. With the
chip selected, when WE is HIGH and OE is LOW, output data will be present on the
DQ pins; when WE is LOW, the data present on the DQ pins will be written into the
selected memory location.
OE Output Enable Input
The output enable input is active LOW. If the output enable is active while the chip is
selected and the write enable is inactive, data will be present on the DQ pins and they
will be enabled. The DQ pins will be in the high impendence state when OE is inactive.
DQ0-DQ7 Data Input/Output
There 8 bi-directional ports are used to read data from or write data into the RAM.
Ports
VCC
Power Supply
GND
Ground
n TRUTH TABLE
MODE
CE
WE
OE
I/O OPERATION
VCC CURRENT
Not selected
(Power Down)
H
X
X
High Z
ICCSB, ICCSB1
Output Disabled
L
H
H
High Z
ICC
Read
L
H
L
DOUT
ICC
Write
L
L
X
DIN
ICC
n ABSOLUTE MAXIMUM RATINGS
TBIAS
TSTG
n OPERATING RANGE
RATING
UNITS
RANG
AMBIENT
TEMPERATURE
VCC
Terminal Voltage with
Respect to GND
Temperature Under
Bias
-0.5(2) to 7.0
V
Commercial
0OC to + 70OC
2.4V ~ 5.5V
-40 to +125
O
C
Industrial
-40OC to + 85OC
2.4V ~ 5.5V
Storage Temperature
-60 to +150
O
C
SYMBOL
VTERM
(1)
PARAMETER
PT
Power Dissipation
1.0
W
IOUT
DC Output Current
20
mA
n CAPACITANCE
O
(TA = 25 C, f = 1.0MHz)
SYMBOL PAMAMETER CONDITIONS MAX. UNITS
1. Stresses greater than those listed under ABSOLUTE
MAXIMUM RATINGS may cause permanent damage to the
device. This is a stress rating only and functional operation of
the device at these or any other conditions above those
indicated in the operational sections of this specification is not
implied. Exposure to absolute maximum rating conditions for
extended periods may affect reliability.
2. –2.0V in case of AC pulse width less than 30 ns.
R0201-BS62LV4006
(1)
CIN
CIO
Input
Capacitance
Input/Output
Capacitance
VIN = 0V
6
pF
VI/O = 0V
8
pF
1. This parameter is guaranteed and not 100% tested.
2
Revision 1.4
May.
2006
BS62LV4006
O
O
n DC ELECTRICAL CHARACTERISTICS (TA = -40 C to +85 C)
PARAMETER
NAME
PARAMETER
TEST CONDITIONS
MIN.
TYP.(1)
MAX.
UNITS
2.4
--
5.5
V
VCC
Power Supply
VIL
Input Low Voltage
-0.5(2)
--
0.8
V
VIH
Input High Voltage
2.2
--
VCC+0.3(3)
V
IIL
Input Leakage Current
VCC = Max, VIN = 0V to VCC
--
--
1
UA
ILO
Output Leakage Current
V CC = Max, CE= VIH, or OE = VIH,
VI/O = 0V to V CC
--
--
1
UA
VOL
Output Low Voltage
V CC = Max, IOL = 2.0mA
--
--
0.4
V
VOH
Output High Voltage
V CC = Min, IOH = -1.0mA
2.4
--
--
V
ICC(5)
Operating Power Supply
Current
CE = VIL,
IDQ = 0mA, f = FMAX(4)
VCC=3.0V
--
--
Operating Power Supply
Current
CE = VIL,
IDQ = 0mA, f = 1MHz
VCC=3.0V
--
--
Standby Current – TTL
CE = VIH,
IDQ = 0mA
VCC=3.0V
--
--
Standby Current – CMOS
CE≧VCC-0.2V,
VIN≧V CC-0.2V or VIN≦0.2V
VCC=3.0V
ICC1
ICCSB
ICCSB1(6)
VCC=5.0V
VCC=5.0V
VCC=5.0V
1. Typical characteristics are at TA=25OC and not 100% tested.
2. Undershoot: -1.0V in case of pulse width less than 20 ns.
3. Overshoot: VCC+1.0V in case of pulse width less than 20 ns.
--
VCC=5.0V
30
mA
70
2
mA
10
0.5
1.0
0.25
4.0
1.5
20
mA
uA
4. FMAX=1/tRC.
5. ICC (MAX.) is 29mA/68mA at VCC=3.0V/5.0V and TA=70OC.
6. ICCSB1(MAX.) is 2.0uA/10uA at VCC=3.0V/5.0V and TA=70OC.
O
O
n DATA RETENTION CHARACTERISTICS (TA = -40 C to +85 C)
SYMBOL
PARAMETER
TEST CONDITIONS
MIN.
TYP. (1)
MAX.
UNITS
VDR
VCC for Data Retention
CE≧VCC-0.2V,
VIN≧VCC-0.2V or VIN≦0.2V
1.5
--
--
V
ICCDR(3)
Data Retention Current
CE≧VCC-0.2V,
VIN≧VCC-0.2V or VIN≦0.2V
--
0.1
1.5
uA
tCDR
Chip Deselect to Data
Retention Time
0
--
--
ns
tRC (2)
--
--
ns
tR
See Retention Waveform
Operation Recovery Time
1. VCC=1.5V, TA=25OC and not 100% tested.
2. tRC = Read Cycle Time.
3. ICCRD(Max.) is 1.0uA at TA=70OC.
n LOW VCC DATA RETENTION WAVEFORM (1) (CE Controlled)
Data Retention Mode
VCC
VCC
VDR≧1.5V
tCDR
CE
R0201-BS62LV4006
VIH
VCC
tR
CE≧VCC - 0.2V
3
VIH
Revision 1.4
May.
2006
BS62LV4006
n AC TEST CONDITIONS
n KEY TO SWITCHING WAVEFORMS
(Test Load and Input/Output Reference)
Input Pulse Levels
Vcc / 0V
Input Rise and Fall Times
1V/ns
Input and Output Timing
Reference Level
0.5Vcc
Output Load
WAVEFORM
tCLZ, tOLZ, tCHZ, tOHZ, tWHZ
CL = 5pF+1TTL
Others
CL = 30pF+1TTL
ALL INPUT PULSES
VCC
1 TTL
Output
90%
GND
CL(1)
90%
10%
10%
→ ←
Rise Time :
1V/ns
→ ←
Fall Time :
1V/ns
INPUTS
OUTPUTS
MUST BE
STEADY
MUST BE
STEADY
MAY CHANGE
FROM “H” TO “L”
WILL BE CHANGE
FROM “H” TO “L”
MAY CHANGE
FROM “L” TO “H”
WILL BE CHANGE
FROM “L” TO “H”
DON’T CARE
ANY CHANGE
PERMITTED
CHANGE :
STATE UNKNOW
DOES NOT
APPLY
CENTER LINE IS
HIGH INPEDANCE
“OFF” STATE
1. Including jig and scope capacitance.
O
O
n AC ELECTRICAL CHARACTERISTICS (TA = -40 C to +85 C)
READ CYCLE
JEDEC
PARANETER
PARAMETER
NAME
NAME
CYCLE TIME : 55ns
(VCC = 3.0~5.5V)
MIN. TYP. MAX.
DESCRIPTION
CYCLE TIME : 70ns
(VCC = 2.7~5.5V)
MIN. TYP. MAX.
UNITS
tAVAX
tRC
Read Cycle Time
55
--
--
70
--
--
ns
tAVQX
tAA
Address Access Time
--
--
55
--
--
70
ns
tE1LQV
tACS
Chip Select Access Time
--
--
55
--
--
70
ns
tGLQV
tOE
Output Enable to Output Valid
--
--
30
--
--
35
ns
tE1LQX
tCLZ
Chip Select to Output Low Z
10
--
--
10
--
--
ns
tGLQX
tOLZ
Output Enable to Output Low Z
5
--
--
5
--
--
ns
tE1HQZ
tCHZ
Chip Select to Output High Z
--
--
30
--
--
35
ns
tGHQZ
tOHZ
Output Enable to Output High Z
--
--
25
--
--
30
ns
tAVQX
tOH
Data Hold from Address Change
10
--
--
10
--
--
ns
R0201-BS62LV4006
4
Revision 1.4
May.
2006
BS62LV4006
n SWITCHING WAVEFORMS (READ CYCLE)
READ CYCLE 1
(1,2,4)
tRC
ADDRESS
tAA
tOH
tOH
DOUT
READ CYCLE 2
(1,3,4)
CE
tACS
tCLZ
tCHZ
(5)
(5)
DOUT
READ CYCLE 3
(1, 4)
tRC
ADDRESS
tAA
OE
tOH
tOE
tOLZ
CE
tACS
tCLZ
(5)
tOHZ
tCHZ
(5)
(1,5)
DOUT
NOTES:
1. WE is high in read Cycle.
2. Device is continuously selected when CE = VIL.
3. Address valid prior to or coincident with CE transition low.
4. OE = VIL.
5. Transition is measured ± 500mV from steady state with CL = 5pF.
The parameter is guaranteed but not 100% tested.
R0201-BS62LV4006
5
Revision 1.4
May.
2006
BS62LV4006
O
O
n AC ELECTRICAL CHARACTERISTICS (TA = -40 C to +85 C)
WRITE CYCLE
JEDEC
PARANETER
PARAMETER
NAME
NAME
DESCRIPTION
CYCLE TIME : 55ns
(VCC = 3.0~5.5V)
CYCLE TIME : 70ns
(VCC = 2.7~5.5V)
MIN.
TYP.
MAX.
MIN.
TYP.
MAX.
UNITS
tAVAX
tWC
Write Cycle Time
55
--
--
70
--
--
ns
tE1LWH
tCW
Chip Select to End of Write
55
--
--
70
--
--
ns
tAVWL
tAS
Address Set up Time
0
--
--
0
--
--
ns
tAVWH
tAW
Address Valid to End of Write
55
--
--
70
--
--
ns
tWLWH
tWP
Write Pulse Width
30
--
--
35
--
--
ns
tWHAX
tWR
Write Recovery Time
0
--
--
0
--
--
ns
tWLQZ
tWHZ
Write to Output High Z
--
--
25
--
--
30
ns
tDVWH
tDW
Data to Write Time Overlap
25
--
--
30
--
--
ns
tWHDX
tDH
Data Hold from Write Time
0
--
--
0
--
--
ns
tGHQZ
tOHZ
Output Disable to Output in High Z
--
--
25
--
--
30
ns
tWHQX
tOW
End of Write to Output Active
5
--
--
5
--
--
ns
(CE, WE)
n SWITCHING WAVEFORMS (WRITE CYCLE)
WRITE CYCLE 1
(1)
tWC
ADDRESS
tWR
(3)
OE
tCW
(11)
(5)
CE
tAW
WE
tWP
tAS
tOHZ
(2)
(4,10)
DOUT
tDH
tDW
DIN
R0201-BS62LV4006
6
Revision 1.4
May.
2006
BS62LV4006
WRITE CYCLE 2
(1,6)
tWC
ADDRESS
tCW
(5)
CE
(11)
tAW
tWP
WE
tAS
tWHZ
(2)
(4,10)
tOW
(7)
(8)
DOUT
tDW
tDH
(8,9)
DIN
NOTES:
1. WE must be high during address transitions.
2. The internal write time of the memory is defined by the overlap of CE and WE low. All
signals must be active to initiate a write and any one signal can terminate a write by going
inactive. The data input setup and hold timing should be referenced to the second transition
edge of the signal that terminates the write.
3. tWR is measured from the earlier of CE or WE going high at the end of write cycle.
4. During this period, DQ pins are in the output state so that the input signals of opposite
phase to the outputs must not be applied.
5. If the CE low transition occurs simultaneously with the WE low transitions or after the WE
transition, output remain in a high impedance state.
6. OE is continuously low (OE = VIL).
7. DOUT is the same phase of write data of this write cycle.
8. DOUT is the read data of next address.
9. If CE is low during this period, DQ pins are in the output state. Then the data input signals
of opposite phase to the outputs must not be applied to them.
10. Transition is measured ± 500mV from steady state with CL = 5pF.
The parameter is guaranteed but not 100% tested.
11. tCW is measured from the later of CE going low to the end of write.
R0201-BS62LV4006
7
Revision 1.4
May.
2006
BS62LV4006
n ORDERING INFORMATION
BS62LV4006
X
X
Z
YY
SPEED
55: 55ns
70: 70ns
PKG MATERIAL
-: Normal
G: Green, RoHS Compliant
P: Pb free, RoHS Compliant
GRADE
C: +0oC ~ +70oC
I: -40oC ~ +85oC
PACKAGE
D: DICE
E: TSOP II
H: BGA-36-0608
P: PDIP
S: SOP
T: TSOP (8mm x 20mm)
ST: Small TSOP (8mm x 13.4mm)
Note:
BSI (Brilliance Semiconductor Inc.) assumes no responsibility for the application or use of any product or circuit described herein. BSI does
not authorize its products for use as critical components in any application in which the failure of the BSI product may be expected to result
in significant injury or death, including life-support systems and critical medical instruments.
n PACKAGE DIMENSIONS
WITH PLATING
c
b
c1
b1
BASE METAL
SECTION
A-A
SOP -32
R0201-BS62LV4006
8
Revision 1.4
May.
2006
BS62LV4006
n PACKAGE DIMENSIONS (continued)
STSOP - 32
TSOP - 32
R0201-BS62LV4006
9
Revision 1.4
May.
2006
BS62LV4006
n PACKAGE DIMENSIONS (continued)
PDIP - 32
NOTES
:
1: CONTROLLING DIMENSIONS ARE IN MILLIMETERS.
2: PIN#1 DOT MARKING BY LASER OR PAD PRINT.
1.2 Max.
3: SYMBOL "N" IS THE NUMBER OF SOLDER BALLS.
BALL PITCH e = 0.75
D
E
N
D1
E1
8.0
6.0
48
5.25
3.75
E1
e
D1
VIEW A
36 mini-BGA (6 x 8mm)
R0201-BS62LV4006
10
Revision 1.4
May.
2006
BS62LV4006
n PACKAGE DIMENSIONS (continued)
DIMENSION
(MM)
17
32
MIN.
NOM.
b
T X
0.20
E1 -XE
e
16
"X"
Y Y
0.05
0.10
0.15
0.002
0.004
0.006
1.00
1.05
0.037
0.039
0.042
b
0.30
0.52
0.012
b1
0.30
0.45
0.012
c
0.12
0.21
0.005
c1
0.10
0.127
0.16
0.004
0.005
0.006
D
20.82
20.95
21.08
0.820
0.825
0.830
E
11.56
11.76
11.96
0.455
0.463
0.471
E1
10.03
10.16
10.29
0.394
0.400
0.405
0.40
0.50
0.60
0.016
A2
A
R1
0.12
A1
Y
0.018
0.008
0.024
0.020
0.010 BASIC
0.8 REF
0.12
0.020
0.016
0.050 BASIC
0.25 BASIC
R
ZD
0.40
1.27 BASIC
L2
SEATING PLANE
MAX.
0.047
0.95
L1
Y
NOM.
A2
L
D
MIN.
A1
e
ZD
MAX.
1.20
A
1
DIMENSION
(INCH)
0.031 REF
0.25
0.005
0.010
0.005
0.95 REF
0.037 REF
0.10
0.004
0.44 REF
-T-
L1
L
RAD R1
L2
0.44 REF
0°~8°
c
GAGE PLANE
DETAIL "X"
WITH PLATING
c1
c
b
b1
RAD R
BASE METAL
NOTE:
1. CONTROLLING DIMENSION : MILLIMETERS.
2. REFREENCE DOCUMENT : JEDEC MS-024
3. DIMENSION D DOES NOT INCLUDE MOLD PROTRUSION.
MOLD PROTRUSION SHALL NOT EXCEED 0.15(0.006") PER SIDE.
DIMENSION E1 DOES NOT INCLUDE INTERLEAD PROTRUSION.
INTERLEAD PROTRUSION SHALL NOT EXCEED 0.25(0.01") PER SIDE.
4. DIMENSION b DOES NOT INCLUDE DAMBAR PROTRUSIONS/INTRUSION.
ALLOWABLE DAMBAR PROTRUSION SHALL NOT CAUSE THE LEAD TO
BE WIDER THAN THE MAX b DIMENSION BY MORE THAN 0.13mm
DAMBAR INTRUSION SHALL NOT CAUSE THE LEAD TO BE NARROWER
THAN THE MIN b DIMENSION BY MORE THAN 0.07mm.
SECTION Y-Y
TSOP II - 32
R0201-BS62LV4006
11
Revision 1.4
May.
2006
BS62LV4006
n Revision History
Revision No.
History
Draft Date
1.2
To add Icc1 characteristic parameter
To improve Iccsb1 spec.
I-grade from 60uA to 20uA at 5.0V
10uA to 4.0uA at 3.0V
C-grade from 30uA to 10uA at 5.0V
5.0uA to 2.0uA at 3.0V
Jan. 13, 2006
1.3
To Add 400 mil TSOP II package type
March 20, 2006
1.4
Change I-grade operation temperature range
- from –25OC to –40OC
May. 25, 2006
R0201-BS62LV4006
12
Remark
Revision 1.4
May.
2006
Similar pages