MOTOROLA MC68HC912DG128

Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MC68HC912DG128
Technical Data
M68HC12
Microcontrollers
MC68HC912DG128/D
Rev. 3, 10/2002
MOTOROLA.COM/SEMICONDUCTORS
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
MC68HC912DG128
Freescale Semiconductor, Inc...
Technical Data — Rev 3.0
Motorola reserves the right to make changes without further notice to any products
herein. Motorola makes no warranty, representation or guarantee regarding the
suitability of its products for any particular purpose, nor does Motorola assume any
liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation consequential or incidental
damages. "Typical" parameters which may be provided in Motorola data sheets and/or
specifications can and do vary in different applications and actual performance may
vary over time. All operating parameters, including "Typicals" must be validated for
each customer application by customer’s technical experts. Motorola does not convey
any license under its patent rights nor the rights of others. Motorola products are not
designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life,
or for any other application in which the failure of the Motorola product could create a
situation where personal injury or death may occur. Should Buyer purchase or use
Motorola products for any such unintended or unauthorized application, Buyer shall
indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and
distributors harmless against all claims, costs, damages, and expenses, and
reasonable attorney fees arising out of, directly or indirectly, any claim of personal
injury or death associated with such unintended or unauthorized use, even if such claim
alleges that Motorola was negligent regarding the design or manufacture of the part.
Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer.
Motorola and
are registered trademarks of Motorola, Inc.
DigitalDNA is a trademark of Motorola, Inc.
MC68HC912DG128 — Rev 3.0
© Motorola, Inc., 2002
Technical Data
MOTOROLA
3
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data
MC68HC912DG128 — Rev 3.0
4
MOTOROLA
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
List of Paragraphs
List of Paragraphs. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Freescale Semiconductor, Inc...
Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
List of Tables . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Section 1. General Description . . . . . . . . . . . . . . . . . . . . 23
Section 2. Central Processing Unit . . . . . . . . . . . . . . . . . 29
Section 3. Pinout and Signal Descriptions . . . . . . . . . . . 37
Section 4. Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Section 5. Operating Modes. . . . . . . . . . . . . . . . . . . . . . . 75
Section 6. Bus Control and Input/Output . . . . . . . . . . . . 95
Section 7. Flash Memory . . . . . . . . . . . . . . . . . . . . . . . . 107
Section 8. EEPROM Memory . . . . . . . . . . . . . . . . . . . . . 125
Section 9. Resets and Interrupts . . . . . . . . . . . . . . . . . . 133
Section 10. I/O Ports with Key Wake-up . . . . . . . . . . . . 147
Section 11. Clock Functions . . . . . . . . . . . . . . . . . . . . . 155
Section 12. Pulse Width Modulator . . . . . . . . . . . . . . . . 191
Section 13. Enhanced Capture Timer . . . . . . . . . . . . . . 207
Section 14. Multiple Serial Interface . . . . . . . . . . . . . . . 249
Section 15. Inter-IC Bus . . . . . . . . . . . . . . . . . . . . . . . . . 273
Section 16. Analog-to-Digital Converter . . . . . . . . . . . . 297
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
List of Paragraphs
For More Information On This Product,
Go to: www.freescale.com
5
Freescale Semiconductor, Inc.
List of Paragraphs
Section 17. MSCAN Controller . . . . . . . . . . . . . . . . . . . . 311
Section 18. Development Support. . . . . . . . . . . . . . . . . 355
Section 19. Electrical Specifications. . . . . . . . . . . . . . . 385
Section 20. Appendix: CGM Practical Aspects . . . . . . 407
Section 21. Appendix: MC68HC912DG128A Flash . . . 419
Section 22. Appendix: MC68HC912DG128A EEPROM 427
Freescale Semiconductor, Inc...
Section 23. Revision History . . . . . . . . . . . . . . . . . . . . . 439
Glossary. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 441
Technical Data
6
MC68HC912DG128 — Rev 3.0
List of Paragraphs
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Table of Contents
List of Paragraphs
Freescale Semiconductor, Inc...
Table of Contents
List of Figures
List of Tables
Section 1. General Description
1.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
1.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
1.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
1.4
Ordering Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
1.5
MC68HC912DG128 Block Diagram . . . . . . . . . . . . . . . . . . . . . 28
Section 2. Central Processing Unit
2.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2.3
Programming Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2.4
Data Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2.5
Addressing Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
2.6
Indexed Addressing Modes . . . . . . . . . . . . . . . . . . . . . . . . . . .34
2.7
Opcodes and Operands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
7
Freescale Semiconductor, Inc.
Table of Contents
Freescale Semiconductor, Inc...
Section 3. Pinout and Signal Descriptions
3.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
3.2
Pin Assignments in 112-pin QFP . . . . . . . . . . . . . . . . . . . . . . . 37
3.3
Power Supply Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
3.4
Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3.5
Port Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
Section 4. Registers
4.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
4.2
Register Block. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
Section 5. Operating Modes
5.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
5.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
5.3
Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
5.4
Background Debug Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
5.5
Internal Resource Mapping. . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
5.6
Memory Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Section 6. Bus Control and Input/Output
6.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
6.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
6.3
Detecting Access Type from External Signals . . . . . . . . . . . . .95
6.4
Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
Section 7. Flash Memory
7.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
7.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
Technical Data
8
MC68HC912DG128 — Rev 3.0
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Table of Contents
7.3
Future Flash EEPROM Support . . . . . . . . . . . . . . . . . . . . . . . 108
7.4
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
7.5
Flash EEPROM Control Block . . . . . . . . . . . . . . . . . . . . . . . . 109
7.6
Flash EEPROM Arrays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
7.7
Flash EEPROM Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
7.8
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
7.9
Programming the Flash EEPROM . . . . . . . . . . . . . . . . . . . . . 118
7.10
Erasing the Flash EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . 120
7.11
Program/Erase Protection Interlocks . . . . . . . . . . . . . . . . . . .122
7.12
Stop or Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
7.13
Test Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
Section 8. EEPROM Memory
8.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
8.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
8.3
Future EEPROM Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
8.4
EEPROM Programmer’s Model . . . . . . . . . . . . . . . . . . . . . . . 127
8.5
EEPROM Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 128
Section 9. Resets and Interrupts
9.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
9.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
9.3
Maskable interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
9.4
Latching of Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
9.5
Interrupt Control and Priority Registers . . . . . . . . . . . . . . . . . 137
9.6
Interrupt test registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
9.7
Resets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .140
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
9
Freescale Semiconductor, Inc.
Table of Contents
9.8
Effects of Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
9.9
Register Stacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 144
9.10
Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 145
Freescale Semiconductor, Inc...
Section 10. I/O Ports with Key Wake-up
10.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
10.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
10.3
Key Wake-up and Port Registers . . . . . . . . . . . . . . . . . . . . . .148
10.4
Key Wake-Up Input Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
Section 11. Clock Functions
11.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
11.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
11.3
Clock Sources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
11.4
Phase-Locked Loop (PLL) . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
11.5
Acquisition and Tracking Modes. . . . . . . . . . . . . . . . . . . . . . . 159
11.6
Limp-Home and Fast STOP Recovery modes . . . . . . . . . . . . 161
11.7
System Clock Frequency formulas . . . . . . . . . . . . . . . . . . . . . 179
11.8
Clock Divider Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
11.9
Computer Operating Properly (COP) . . . . . . . . . . . . . . . . . . .184
11.10 Real-Time Interrupt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
11.11 Clock Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
11.12 Clock Function Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Section 12. Pulse Width Modulator
12.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
12.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
Technical Data
10
MC68HC912DG128 — Rev 3.0
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Table of Contents
12.3
PWM Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
12.4
PWM Boundary Cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
Freescale Semiconductor, Inc...
Section 13. Enhanced Capture Timer
13.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
13.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
13.3
Enhanced Capture Timer Modes of Operation . . . . . . . . . . . . 214
13.4
Timer Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
13.5
Timer and Modulus Counter Operation in Different Modes . . 247
Section 14. Multiple Serial Interface
14.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
14.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
14.3
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250
14.4
Serial Communication Interface (SCI) . . . . . . . . . . . . . . . . . . 250
14.5
Serial Peripheral Interface (SPI) . . . . . . . . . . . . . . . . . . . . . . . 262
14.6
Port S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271
Section 15. Inter-IC Bus
15.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273
15.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273
15.3
IIC Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
15.4
IIC System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
15.5
IIC Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
15.6
IIC Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
15.7
IIC Programming Examples . . . . . . . . . . . . . . . . . . . . . . . . . .290
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
11
Freescale Semiconductor, Inc.
Table of Contents
Freescale Semiconductor, Inc...
Section 16. Analog-to-Digital Converter
16.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
16.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
16.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298
16.4
ATD Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299
16.5
ATD Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310
Section 17. MSCAN Controller
17.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311
17.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311
17.3
External Pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312
17.4
Message Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
17.5
Identifier Acceptance Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . 318
17.6
Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
17.7
Protocol Violation Protection. . . . . . . . . . . . . . . . . . . . . . . . . . 324
17.8
Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .325
17.9
Timer Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
17.10 Clock System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
17.11 Memory Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332
17.12 Programmer’s Model of Message Storage . . . . . . . . . . . . . . .332
17.13 Programmer’s Model of Control Registers . . . . . . . . . . . . . . . 338
Section 18. Development Support
18.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355
18.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355
18.3
Instruction Queue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355
18.4
Background Debug Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357
Technical Data
12
MC68HC912DG128 — Rev 3.0
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Table of Contents
18.5
Breakpoints. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375
18.6
Instruction Tagging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382
Freescale Semiconductor, Inc...
Section 19. Electrical Specifications
19.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385
19.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385
19.3
Tables of Data
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386
Section 20. Appendix: CGM Practical Aspects
20.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407
20.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407
20.3
A Few Hints For The CGM Crystal Oscillator Application. . . . 407
20.4
Practical Aspects For The PLL Usage . . . . . . . . . . . . . . . . . . 410
20.5
Printed Circuit Board Guidelines. . . . . . . . . . . . . . . . . . . . . . . 415
Section 21. Appendix: MC68HC912DG128A Flash
21.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419
21.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419
21.3
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420
21.4
Flash EEPROM Control Block . . . . . . . . . . . . . . . . . . . . . . . . 420
21.5
Flash EEPROM Arrays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420
21.6
Flash EEPROM Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . 421
21.7
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .423
21.8
Programming the Flash EEPROM . . . . . . . . . . . . . . . . . . . . . 424
21.9
Erasing the Flash EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . 425
21.10 Stop or Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .425
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
13
Freescale Semiconductor, Inc.
Table of Contents
Freescale Semiconductor, Inc...
Section 22. Appendix: MC68HC912DG128A EEPROM
22.1
Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 427
22.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 427
22.3
EEPROM Programmer’s Model . . . . . . . . . . . . . . . . . . . . . . . 428
22.4
EEPROM Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 430
22.5
Program/Erase Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 436
22.6
Shadow Word Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436
22.7
Programming EEDIVH and EEDIVL Registers. . . . . . . . . . . . 437
Section 23. Revision History
Glossary
Technical Data
14
MC68HC912DG128 — Rev 3.0
Table of Contents
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
List of Figures
Figure
Freescale Semiconductor, Inc...
2-1
3-1
3-2
3-3
3-4
3-5
5-1
5-2
6-1
7-1
7-2
10-1
11-1
11-2
11-3
11-4
11-5
11-6
11-7
11-8
11-9
12-1
12-2
12-3
13-1
13-2
13-3
13-4
Title
Programming Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
MC68HC912DG128 Pin Assignments in 112-pin QFP. . . . . . . 38
112-pin QFP Mechanical Dimensions (case no987) . . . . . . . . 39
PLL Loop FIlter Connections . . . . . . . . . . . . . . . . . . . . . . . . . . 41
Common Crystal Connections . . . . . . . . . . . . . . . . . . . . . . . . . 43
External Oscillator Connections . . . . . . . . . . . . . . . . . . . . . . . . 43
Memory Map after reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
Memory Paging. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .94
Access Type vsBus Control Pins . . . . . . . . . . . . . . . . . . . . . . . 96
Program Sequence Flow . . . . . . . . . . . . . . . . . . . . . . . . . . . . 119
Erase Sequence Flow. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 121
STOP Key Wake-up Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . 153
Internal Clock Relationships . . . . . . . . . . . . . . . . . . . . . . . . . . 157
PLL Functional Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . .158
Clock Loss during Normal Operation . . . . . . . . . . . . . . . . . . .162
No Clock at Power-On Reset . . . . . . . . . . . . . . . . . . . . . . . . . 164
STOP Exit and Fast STOP Recovery . . . . . . . . . . . . . . . . . . . 167
Clock Generation Chain . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
Clock Chain for SCI0, SCI1, RTI, COP. . . . . . . . . . . . . . . . . . 181
Clock Chain for ECT . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 182
Clock Chain for MSCAN, SPI, ATD0, ATD1 and BDM . . . . . . 183
Block Diagram of PWM Left-Aligned Output Channel . . . . . . 192
Block Diagram of PWM Center-Aligned Output Channel . . . . 193
PWM Clock Sources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 194
Timer Block Diagram in Latch Mode. . . . . . . . . . . . . . . . . . . . 209
Timer Block Diagram in Queue Mode. . . . . . . . . . . . . . . . . . . 210
8-Bit Pulse Accumulators Block Diagram . . . . . . . . . . . . . . . . 211
16-Bit Pulse Accumulators Block Diagram . . . . . . . . . . . . . . .212
MC68HC912DG128 — Rev 3.0
MOTOROLA
Page
Technical Data
List of Figures
For More Information On This Product,
Go to: www.freescale.com
15
Freescale Semiconductor, Inc.
List of Figures
13-5
Freescale Semiconductor, Inc...
13-6
14-1
14-2
14-3
14-4
14-5
14-6
15-1
15-2
15-3
15-4
16-1
17-1
17-2
17-3
17-4
17-5
17-6
17-7
17-8
17-9
17-10
17-11
17-12
17-13
17-14
17-15
17-16
17-17
18-1
18-2
18-3
19-1
19-2
19-3
19-4
Block Diagram for Port7 with Output compare / Pulse
Accumulator A . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 213
C3F-C0F Interrupt Flag Setting . . . . . . . . . . . . . . . . . . . . . . . 213
Multiple Serial Interface Block Diagram . . . . . . . . . . . . . . . . . 250
Serial Communications Interface Block Diagram . . . . . . . . . . 251
Serial Peripheral Interface Block Diagram . . . . . . . . . . . . . . . 263
SPI Clock Format 0 (CPHA = 0) . . . . . . . . . . . . . . . . . . . . . . . 264
SPI Clock Format 1 (CPHA = 1) . . . . . . . . . . . . . . . . . . . . . . . 265
Normal Mode and Bidirectional Mode. . . . . . . . . . . . . . . . . . . 266
IIC Block Diagram. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 275
IIC Transmission Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
IIC Clock Synchronization. . . . . . . . . . . . . . . . . . . . . . . . . . . . 280
Flow-Chart of Typical IIC Interrupt Routine . . . . . . . . . . . . . . 295
Analog-to-Digital Converter Block Diagram . . . . . . . . . . . . . . 298
The CAN System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
User Model for Message Buffer Organization. . . . . . . . . . . . . 316
32-bit Maskable Identifier Acceptance Filters . . . . . . . . . . . . . 320
16-bit Maskable Acceptance Filters . . . . . . . . . . . . . . . . . . . . 320
8-bit Maskable Acceptance Filters . . . . . . . . . . . . . . . . . . . . . 321
SLEEP Request / Acknowledge Cycle . . . . . . . . . . . . . . . . . . 327
Clocking Scheme . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
Segments within the Bit Time . . . . . . . . . . . . . . . . . . . . . . . . . 331
CAN Standard Compliant Bit Time Segment Settings . . . . . . 331
msCAN12 Memory Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . .332
Message Buffer Organization . . . . . . . . . . . . . . . . . . . . . . . . . 333
Receive/Transmit Message Buffer Extended Identifier. . . . . . 334
Standard Identifier Mapping . . . . . . . . . . . . . . . . . . . . . . . . . .335
Identifier Acceptance Registers (1st bank) . . . . . . . . . . . . . . .351
Identifier Acceptance Registers (2nd bank) . . . . . . . . . . . . . . 351
Identifier Mask Registers (1st bank) . . . . . . . . . . . . . . . . . . . . 352
Identifier Mask Registers (2nd bank) . . . . . . . . . . . . . . . . . . .352
BDM Host to Target Serial Bit Timing. . . . . . . . . . . . . . . . . . . 359
BDM Target to Host Serial Bit Timing (Logic 1) . . . . . . . . . . . 359
BDM Target to Host Serial Bit Timing (Logic 0) . . . . . . . . . . . 360
VFP Conditioning Circuit . . . . . . . . . . . . . . . . . . . . . . . . . . . . .393
VFP Operating Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 394
Timer Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395
POR and External Reset Timing Diagram . . . . . . . . . . . . . . . 396
Technical Data
16
MC68HC912DG128 — Rev 3.0
List of Figures
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
List of Figures
19-5
19-6
19-7
19-8
19-9
19-10
Freescale Semiconductor, Inc...
19-11
19-11
19-11
19-12
STOP Recovery Timing Diagram . . . . . . . . . . . . . . . . . . . . . .397
WAIT Recovery Timing Diagram . . . . . . . . . . . . . . . . . . . . . . 398
Interrupt Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . 399
Port Read Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . 400
Port Write Timing Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . 400
Multiplexed Expansion Bus Timing Diagram . . . . . . . . . . . . . 402
A) SPI Master Timing (CPHA = 0) . . . . . . . . . . . . . . . . . . . . . 404
B) SPI Master Timing (CPHA = 1) . . . . . . . . . . . . . . . . . . . . . 404
SPI Timing Diagram (1 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . 404
A) SPI Slave Timing (CPHA = 0) . . . . . . . . . . . . . . . . . . . . . . 405
B) SPI Slave Timing (CPHA = 1) . . . . . . . . . . . . . . . . . . . . . . 405
SPI Timing Diagram (2 of 2) . . . . . . . . . . . . . . . . . . . . . . . . . . 405
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
List of Figures
For More Information On This Product,
Go to: www.freescale.com
17
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
List of Figures
Technical Data
18
MC68HC912DG128 — Rev 3.0
List of Figures
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
List of Tables
Table
Freescale Semiconductor, Inc...
1-1
1-2
2-1
2-2
2-3
3-1
3-2
3-3
3-4
4-1
5-1
5-2
5-3
5-4
5-5
5-6
5-7
7-1
8-1
8-2
9-1
9-2
11-1
11-2
11-3
11-4
11-5
12-1
12-2
Title
Device Ordering Information. . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Development Tools Ordering Information. . . . . . . . . . . . . . . . . 27
M68HC12 Addressing Mode Summary . . . . . . . . . . . . . . . . . . 32
M68HC12 Addressing Mode Summary . . . . . . . . . . . . . . . . . . 33
Summary of Indexed Operations . . . . . . . . . . . . . . . . . . . . . . . 34
Power and Ground Connection Summary . . . . . . . . . . . . . . . . 42
Signal Description Summary . . . . . . . . . . . . . . . . . . . . . . . . . . 49
Port Description Summary . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
Port Pull-Up, Pull-Down and Reduced Drive Summary . . . . . .60
Register Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 64
Mode Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .76
Mapping Precedence . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 82
Program space Page Index . . . . . . . . . . . . . . . . . . . . . . . . . . .86
Flash Register space Page Index. . . . . . . . . . . . . . . . . . . . . . .86
Test mode program space Page Index. . . . . . . . . . . . . . . . . . . 87
RFSTR Stretch Bit Definition . . . . . . . . . . . . . . . . . . . . . . . . . . 90
EXSTR Stretch Bit Definition . . . . . . . . . . . . . . . . . . . . . . . . . . 91
Effects of ENPE, LAT and ERAS on Array Reads . . . . . . . . . 114
2K byte EEPROM Block Protection . . . . . . . . . . . . . . . . . . . . 129
Erase Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .131
Interrupt Vector Map . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 135
Stacking Order on Entry to Interrupts . . . . . . . . . . . . . . . . . . . 144
Summary of STOP Mode Exit Conditions. . . . . . . . . . . . . . . . 172
Summary of Pseudo STOP Mode Exit Conditions . . . . . . . . . 173
Clock Monitor Time-Outs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
Real Time Interrupt Rates. . . . . . . . . . . . . . . . . . . . . . . . . . . . 186
COP Watchdog Rates . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 189
Clock A and Clock B Prescaler. . . . . . . . . . . . . . . . . . . . . . . . 196
PWM Left-Aligned Boundary Conditions . . . . . . . . . . . . . . . . 206
MC68HC912DG128 — Rev 3.0
MOTOROLA
Page
Technical Data
List of Tables
For More Information On This Product,
Go to: www.freescale.com
19
Freescale Semiconductor, Inc.
List of Tables
Freescale Semiconductor, Inc...
12-3
13-1
13-2
13-3
14-1
14-2
14-3
14-4
15-1
15-2
16-1
16-2
16-3
16-4
17-1
17-2
17-3
17-4
17-5
17-6
17-7
17-8
17-9
18-1
18-2
18-3
18-4
18-5
18-6
18-7
18-8
18-9
18-10
18-11
18-12
19-1
19-2
19-3
PWM Center-Aligned Boundary Conditions . . . . . . . . . . . . . . 206
Compare Result Output Action . . . . . . . . . . . . . . . . . . . . . . . . 222
Edge Detector Circuit Configuration . . . . . . . . . . . . . . . . . . . . 223
Prescaler Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 225
Baud Rate Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 252
Loop Mode Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 255
SS Output Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 265
SPI Clock Rate Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . 269
IIC Tap and Prescale Values . . . . . . . . . . . . . . . . . . . . . . . . . 282
IIC Divider and SDA Hold values . . . . . . . . . . . . . . . . . . . . . . 283
ATD Response to Background Debug Enable . . . . . . . . . . . . 301
Final Sample Time Selection . . . . . . . . . . . . . . . . . . . . . . . . . 302
Clock Prescaler Values. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 303
Multichannel Mode Result Register Assignment . . . . . . . . . . 305
msCAN12 Interrupt Vectors . . . . . . . . . . . . . . . . . . . . . . . . . .324
msCAN12 vsCPU operating modes . . . . . . . . . . . . . . . . . . . . 325
Data length codes. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 336
Synchronization jump width . . . . . . . . . . . . . . . . . . . . . . . . . .341
Baud rate prescaler . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 341
Time segment syntax . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342
Time segment values . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 342
Identifier Acceptance Mode Settings . . . . . . . . . . . . . . . . . . .349
Identifier Acceptance Hit Indication . . . . . . . . . . . . . . . . . . . . 349
IPIPE Decoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 356
Hardware Commands. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 362
BDM Firmware Commands . . . . . . . . . . . . . . . . . . . . . . . . . .363
BDM registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 366
TTAGO Decoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371
TTAGO Value . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371
Instruction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371
REGN Decoding . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 371
Breakpoint Mode Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . 378
Breakpoint Address Range Control . . . . . . . . . . . . . . . . . . . . 379
Breakpoint Read/Write Control . . . . . . . . . . . . . . . . . . . . . . . . 380
Tag Pin Function. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 383
Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386
Thermal Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386
DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . 387
Technical Data
20
MC68HC912DG128 — Rev 3.0
List of Tables
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
List of Tables
Freescale Semiconductor, Inc...
19-4
19-5
19-6
19-7
19-8
19-9
19-10
19-11
19-12
19-13
19-14
19-15
19-16
19-17
19-18
20-1
20-2
22-1
22-2
22-3
22-4
Supply Current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 389
ATD DC Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . 389
Analog Converter Characteristics (Operating) . . . . . . . . . . . .390
ATD AC Characteristics (Operating). . . . . . . . . . . . . . . . . . . . 391
ATD Maximum Ratings. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 391
EEPROM Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . 392
Flash EEPROM Characteristics . . . . . . . . . . . . . . . . . . . . . . . 392
Pulse Width Modulator Characteristics. . . . . . . . . . . . . . . . . . 394
Control Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 395
Peripheral Port Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 400
Multiplexed Expansion Bus Timing. . . . . . . . . . . . . . . . . . . . . 401
SPI Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 403
CGM Characteristics. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406
Key Wake-up . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 406
msCAN12 Wake-up Time from Sleep Mode. . . . . . . . . . . . . . 406
Suggested 8MHz Synthesis PLL Filter Elements
(Tracking Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 413
Suggested 8MHz Synthesis PLL Filter Elements
(Acquisition Mode) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .414
EEDIV Selection . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 431
2K byte EEPROM Block Protection . . . . . . . . . . . . . . . . . . . . 433
Erase Selection. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .434
Shadow word mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
List of Tables
For More Information On This Product,
Go to: www.freescale.com
21
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
List of Tables
Technical Data
22
MC68HC912DG128 — Rev 3.0
List of Tables
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Section 1. General Description
1.1 Contents
1.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
1.3
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
1.4
Ordering Information. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
1.5
MC68HC912DG128 Block Diagram . . . . . . . . . . . . . . . . . . . . . 28
1.2 Introduction
The MC68HC912DG128 microcontroller unit (MCU) is a 16-bit device
composed of standard on-chip peripherals including a 16-bit central
processing unit (CPU12), 128K bytes of flash EEPROM, 8K bytes of
RAM, 2K bytes of EEPROM, two asynchronous serial communication
interfaces (SCI), a serial peripheral interface (SPI), an inter-IC interface
(I2C), an enhanced capture timer (ECT), two 8-channel,10-bit analog-todigital converters (ATD), a four-channel pulse-width modulator (PWM),
and two CAN 2.0 A, B software compatible modules (MSCAN12).
System resource mapping, clock generation, interrupt control and bus
interfacing are managed by the lite integration module (LIM). The
MC68HC912DG128 has full 16-bit data paths throughout, however, the
external bus can operate in an 8-bit narrow mode so single 8-bit wide
memory can be interfaced for lower cost systems. The inclusion of a PLL
circuit allows power consumption and performance to be adjusted to suit
operational requirements. In addition to the I/O ports available in each
module, 16 I/O port pins are available with Key-Wake-Up capability from
STOP or WAIT mode.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
General Description
For More Information On This Product,
Go to: www.freescale.com
23
Freescale Semiconductor, Inc.
General Description
1.3 Features
•
16-bit CPU12
– Upward compatible with M68HC11 instruction set
– Interrupt stacking and programmer’s model identical to
M68HC11
– 20-bit ALU
Freescale Semiconductor, Inc...
– Instruction queue
– Enhanced indexed addressing
•
Multiplexed bus
– Single chip or expanded
– 16 address/16 data wide or 16 address/8 data narrow mode
•
Memory
– 128K byte flash EEPROM, made of four 32K byte modules
with 8K bytes protected BOOT section in each module
– 2K byte EEPROM
– 8K byte RAM, made of two 4K byte modules with Vstby in each
module.
•
Analog-to-digital converters
– 2 times x 8-channels, 10-bit resolution
Technical Data
24
MC68HC912DG128 — Rev 3.0
General Description
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
General Description
Features
•
1M bit per second, CAN 2.0 A, B software compatible modules,
two on the MC68HC912DG128, each with:
– Two receive and three transmit buffers
– Flexible identifier filter programmable as 2 x 32 bit, 4 x 16 bit or
8 x 8 bit
– Four separate interrupt channels for Rx, Tx, error and wake-up
– Low-pass filter wake-up function
Freescale Semiconductor, Inc...
– Loop-back for self test operation
– Programmable link to a timer input capture channel, for timestamping and network synchronization.
•
Enhanced capture timer (ECT)
– 16-bit main counter with 7-bit prescaler
– 8 programmable input capture or output compare channels; 4
of the 8 input captures with buffer
– Input capture filters and buffers, three successive captures on
four channels, or two captures on four channels with a
capture/compare selectable on the remaining four
– Four 8-bit or two 16-bit pulse accumulators
– 16-bit modulus down-counter with 4-bit prescaler
– Four user-selectable delay counters for signal filtering
•
4 PWM channels with programmable period and duty cycle
– 8-bit 4-channel or 16-bit 2-channel
– Separate control for each pulse width and duty cycle
– Center- or left-aligned outputs
– Programmable clock select logic with a wide range of
frequencies
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
General Description
For More Information On This Product,
Go to: www.freescale.com
25
Freescale Semiconductor, Inc.
General Description
•
Serial interfaces
– Two asynchronous serial communications interfaces (SCI)
– Inter IC bus interface (I2C)
– Synchronous serial peripheral interface (SPI)
•
LIM (lite integration module)
– WCR (windowed COP watchdog, real time interrupt, clock
monitor)
Freescale Semiconductor, Inc...
– ROC (reset and clocks)
– MEBI (multiplexed external bus interface)
– MBI (internal bus interface and memory map)
– INT (interrupt control)
•
Two 8-bit ports with key wake-up interrupt
•
Clock generation
– Phase-locked loop clock frequency multiplier
– Limp home mode in absence of external clock
– Slow mode divider
– Low power 0.5 to 16 MHz crystal oscillator reference clock
•
112-Pin TQFP package
– Up to 66 general-purpose I/O lines, plus up to 18 input-only
lines
•
8MHz operation at 5V
•
Development support
– Single-wire background debug™ mode (BDM)
– On-chip hardware breakpoints
Technical Data
26
MC68HC912DG128 — Rev 3.0
General Description
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
General Description
Ordering Information
1.4 Ordering Information
Table 1-1. Device Ordering Information
Temperature
Package
Voltage
Range
Frequency
0 to +70°C
112-Pin TQFP
Single Tray
60 Pcs
Order Number
Designator
68HC912DG128PV8
–40 to +85°C
C
–40 to +105°C
V
68HC912DG128VPV8
–40 to +125°C
M*
68HC912DG128MPV8
68HC912DG128CPV8
4.5V–5.5V
8 MHz
* Important: M temperature operation is available only for single chip modes
Table 1-2. Development Tools Ordering Information
Description
Name
MCUez
Order Number
Free from World Wide Web
Serial Debug Interface
SDI
M68SDIL (3–5V), M68DIL12 (SDIL + MCUez +
SDBUG12)
Evaluation board
EVB
M68EVB912DG128 (EVB only)
M68KIT912DG128 (EVB + SDIL12)
NOTE:
SDBUG12 is a P & E Micro Product. It can be obtained from P & E from
their web site (http://www.pemicro.com) for approximately $100.
Third party tools: http://www.mcu.motsps.com/dev_tools/3rd/index.htm
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
General Description
For More Information On This Product,
Go to: www.freescale.com
27
Freescale Semiconductor, Inc.
General Description
1.5 MC68HC912DG128 Block Diagram
VRH0
PORT E
PE0
PE1
PE2
PE3
PE4
PE5
PE6
PE7
XIRQ
IRQ
R/W
LSTRB
ECLK
MODA
MODB
DBE/CAL
Lite
integration
module
(LIM)
PW0
PW1
PW2
PW3
PWM
PIX0
PIX1
PIX2
PPAGE
PORT T
DDRT
SDI/MISO
SDO/MOSI
SCK
SS
SPI
PORT S
SCI1
I/O
ECS
I/O
PIB7
PIB6
PIB5
PIB4
PORTH
DDRH
TxCAN1
RxCAN1
PH7
PH6
PH5
PH4
PH3
PH2
PH1
PH0
KWJ7
KWJ6
KWJ5
KWJ4
KWJ3
KWJ2
KWJ1
KWJ0
PORTJ
KWU
DDRJ
PB7
PB6
PB5
PB4
PB3
PB2
PB1
PB0
CAN1
ADDR7
ADDR6
ADDR5
ADDR4
ADDR3
ADDR2
ADDR1
ADDR0
PORT B
DATA7
DATA6
DATA5
DATA4
DATA3
DATA2
DATA1
DATA0
PORT A
PA7
PA6
PA5
PA4
PA3
PA2
PA1
PA0
TxCAN0
RxCAN0
ADDR15
ADDR14
ADDR13
ADDR12
ADDR11
ADDR10
ADDR9
ADDR8
CAN0
Narrow bus
VDD ×2
VSS ×2
Power for internal circuitry
VDDX ×2
VSSX ×2
PJ7
PJ6
PJ5
PJ4
PJ3
PJ2
PJ1
PJ0
Technical Data
28
PK0
PK1
PK2
PK3
PK7
DDRB
KWH7
KWH6
KWH5
KWH4
KWH3
KWH2
KWH1
KWH0
PS4
PS5
PS6
PS7
PP0
PP1
PP2
PP3
DDRA
DATA7 DATA15
DATA6 DATA14
DATA5 DATA13
DATA4 DATA12
DATA3 DATA11
DATA2 DATA10
DATA1 DATA9
DATA0 DATA8
Wide
bus
DDRIB
SCL
SDA
IIC
Multiplexed Address/Data Bus
PS0
PS1
PS2
PS3
PORT P
RxD0
TxD0
RxD1
TxD1
SCI0
EXTAL
XTAL
RESET
PORT K
Enhanced
capture
timer
PAD10
PAD11
PAD12
PAD13
PAD14
PAD15
PAD16
PAD17
PT0
PT1
PT2
PT3
PT4
PT5
PT6
PT7
PORTIB
Clock
Generation
module
IOC0
IOC1
IOC2
IOC3
IOC4
IOC5
IOC6
IOC7
DDRS
PLL
Periodic interrupt
COP watchdog
Clock monitor
Breakpoints
AN10
AN11
AN12
AN13
AN14
AN15
AN16
AN17
DDRP
Single-wire
background
debug module
PAD00
PAD01
PAD02
PAD03
PAD04
PAD05
PAD06
PAD07
DDRK
Freescale Semiconductor, Inc...
CPU12
AN00
AN01
AN02
AN03
AN04
AN05
AN06
AN07
VRH1
VRL1
VDDA
VSSA
VDDA
VSSA
PORT AD0
8K byte RAM
2K byte EEPROM
XFC
VDDPLL
VSSPLL
VRH1
ATD1 VRL1
VDDA
VSSA
VSTBY
BKGD
VRH0
VRL0
ATD0 VRL0
PORT AD1
128K byte flash EEPROM
VFP
Power for I/O drivers
MC68HC912DG128 — Rev 3.0
General Description
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Section 2. Central Processing Unit
2.1 Contents
2.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2.3
Programming Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
2.4
Data Types . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
2.5
Addressing Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .31
2.6
Indexed Addressing Modes . . . . . . . . . . . . . . . . . . . . . . . . . . .34
2.7
Opcodes and Operands . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
2.2 Introduction
The CPU12 is a high-speed, 16-bit processing unit. It has full 16-bit data
paths and wider internal registers (up to 20 bits) for high-speed extended
math instructions. The instruction set is a proper superset of the
M68HC11instruction set. The CPU12 allows instructions with odd byte
counts, including many single-byte instructions. This provides efficient
use of ROM space. An instruction queue buffers program information so
the CPU always has immediate access to at least three bytes of machine
code at the start of every instruction. The CPU12 also offers an
extensive set of indexed addressing capabilities.
2.3 Programming Model
CPU12 registers are an integral part of the CPU and are not addressed
as if they were memory locations.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Central Processing Unit
For More Information On This Product,
Go to: www.freescale.com
29
Freescale Semiconductor, Inc.
Central Processing Unit
7
A
0 7
B
0
8-BIT ACCUMULATORS A & B
Freescale Semiconductor, Inc...
OR
15
D
0
16-BIT DOUBLE ACCUMULATOR D
15
IX
0
INDEX REGISTER X
15
IY
0
INDEX REGISTER Y
15
SP
0
STACK POINTER
15
PC
0
PROGRAM COUNTER
S X H I N Z V C
CONDITION CODE REGISTER
Figure 2-1. Programming Model
Accumulators A and B are general-purpose 8-bit accumulators used to
hold operands and results of arithmetic calculations or data
manipulations. Some instructions treat the combination of these two 8bit accumulators as a 16-bit double accumulator (accumulator D).
Index registers X and Y are used for indexed addressing mode. In the
indexed addressing mode, the contents of a 16-bit index register are
added to 5-bit, 9-bit, or 16-bit constants or the content of an accumulator
to form the effective address of the operand to be used in the instruction.
Stack pointer (SP) points to the last stack location used. The CPU12
supports an automatic program stack that is used to save system
context during subroutine calls and interrupts, and can also be used for
temporary storage of data. The stack pointer can also be used in all
indexed addressing modes.
Program counter is a 16-bit register that holds the address of the next
instruction to be executed. The program counter can be used in all
indexed addressing modes except autoincrement/decrement.
Technical Data
30
MC68HC912DG128 — Rev 3.0
Central Processing Unit
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Central Processing Unit
Data Types
Condition Code Register (CCR) contains five status indicators, two
interrupt masking bits, and a STOP disable bit. The five flags are half
carry (H), negative (N), zero (Z), overflow (V), and carry/borrow (C). The
half-carry flag is used only for BCD arithmetic operations. The N, Z, V,
and C status bits allow for branching based on the results of a previous
operation.
After a reset, the CPU fetches a vector from the appropriate address and
begins executing instructions. The X and I interrupt mask bits are set to
mask any interrupt requests. The S bit is also set to inhibit the STOP
instruction.
2.4 Data Types
The CPU12 supports the following data types:
•
Bit data
•
8-bit and 16-bit signed and unsigned integers
•
16-bit unsigned fractions
•
16-bit addresses
A byte is eight bits wide and can be accessed at any byte location. A
word is composed of two consecutive bytes with the most significant
byte at the lower value address. There are no special requirements for
alignment of instructions or operands.
2.5 Addressing Modes
Addressing modes determine how the CPU accesses memory locations
to be operated upon. The CPU12 includes all of the addressing modes
of the M68HC11 CPU as well as several new forms of indexed
addressing. Table 2-1 is a summary of the available addressing modes.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Central Processing Unit
For More Information On This Product,
Go to: www.freescale.com
31
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Central Processing Unit
Table 2-1. M68HC12 Addressing Mode Summary
Addressing Mode
Source Format
INST
(no externally supplied
operands)
INST #opr8i
or
INST #opr16i
Abbreviation
Description
INH
Operands (if any) are in CPU registers
IMM
Operand is included in instruction stream
8- or 16-bit size implied by context
Direct
INST opr8a
DIR
Extended
INST opr16a
INST rel8
or
INST rel16
EXT
REL
An 8-bit or 16-bit relative offset from the current
pc is supplied in the instruction
INST oprx5,xysp
IDX
5-bit signed constant offset from x, y, sp, or pc
INST oprx3,–xys
IDX
Auto pre-decrement x, y, or sp by 1 ~ 8
INST oprx3,+xys
IDX
Auto pre-increment x, y, or sp by 1 ~ 8
INST oprx3,xys–
IDX
Auto post-decrement x, y, or sp by 1 ~ 8
INST oprx3,xys+
IDX
Auto post-increment x, y, or sp by 1 ~ 8
INST abd,xysp
IDX
INST oprx9,xysp
IDX1
INST oprx16,xysp
IDX2
Indexed-Indirect
(16-bit offset)
INST [oprx16,xysp]
[IDX2]
Indexed-Indirect
(D accumulator
offset)
INST [D,xysp]
[D,IDX]
Inherent
Immediate
Relative
Indexed
(5-bit offset)
Indexed
(auto pre-decrement)
Indexed
(auto pre-increment)
Indexed
(auto postdecrement)
Indexed
(auto post-increment)
Indexed
(accumulator offset)
Indexed
(9-bit offset)
Indexed
(16-bit offset)
Operand is the lower 8-bits of an address in the
range $0000 – $00FF
Operand is a 16-bit address
Indexed with 8-bit (A or B) or 16-bit (D)
accumulator offset from x, y, sp, or pc
9-bit signed constant offset from x, y, sp, or pc
(lower 8-bits of offset in one extension byte)
16-bit constant offset from x, y, sp, or pc
(16-bit offset in two extension bytes)
Pointer to operand is found at...
16-bit constant offset from x, y, sp, or pc
(16-bit offset in two extension bytes)
Pointer to operand is found at...
x, y, sp, or pc plus the value in D
Technical Data
32
MC68HC912DG128 — Rev 3.0
Central Processing Unit
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Central Processing Unit
Addressing Modes
Table 2-2. M68HC12 Addressing Mode Summary
Addressing Mode
Source Format
Abbreviation
Description
Inherent
INST
(no externally
supplied operands)
INH
Operands (if any) are in CPU registers
Immediate
INST #opr8i
or
INST #opr16i
IMM
Operand is included in instruction stream
8- or 16-bit size implied by context
Direct
INST opr8a
DIR
Operand is the lower 8-bits of an address in
the range $0000 – $00FF
Extended
INST opr16a
EXT
Operand is a 16-bit address
Relative
INST rel8
or
INST rel16
REL
An 8-bit or 16-bit relative offset from the
current pc is supplied in the instruction
Indexed
(5-bit offset)
INST oprx5,xysp
IDX
5-bit signed constant offset from x, y, sp, or
pc
Indexed
(auto pre-decrement)
INST oprx3,–xys
IDX
Auto pre-decrement x, y, or sp by 1 ~ 8
Indexed
(auto pre-increment)
INST oprx3,+xys
IDX
Auto pre-increment x, y, or sp by 1 ~ 8
Indexed
(auto post-decrement)
INST oprx3,xys–
IDX
Auto post-decrement x, y, or sp by 1 ~ 8
Indexed
(auto post-increment)
INST oprx3,xys+
IDX
Auto post-increment x, y, or sp by 1 ~ 8
Indexed
(accumulator offset)
INST abd,xysp
IDX
Indexed with 8-bit (A or B) or 16-bit (D)
accumulator offset from x, y, sp, or pc
Indexed
(9-bit offset)
INST oprx9,xysp
IDX1
9-bit signed constant offset from x, y, sp, or
pc
(lower 8-bits of offset in one extension byte)
Indexed
(16-bit offset)
INST oprx16,xysp
IDX2
16-bit constant offset from x, y, sp, or pc
(16-bit offset in two extension bytes)
Indexed-Indirect
(16-bit offset)
INST [oprx16,xysp]
[IDX2]
Pointer to operand is found at...
16-bit constant offset from x, y, sp, or pc
(16-bit offset in two extension bytes)
Indexed-Indirect
(D accumulator offset)
INST [D,xysp]
[D,IDX]
Pointer to operand is found at...
x, y, sp, or pc plus the value in D
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Central Processing Unit
For More Information On This Product,
Go to: www.freescale.com
33
Freescale Semiconductor, Inc.
Central Processing Unit
2.6 Indexed Addressing Modes
Freescale Semiconductor, Inc...
The CPU12 indexed modes reduce execution time and eliminate code
size penalties for using the Y index register. CPU12 indexed addressing
uses a postbyte plus zero, one, or two extension bytes after the
instruction opcode. The postbyte and extensions do the following tasks:
•
Specify which index register is used.
•
Determine whether a value in an accumulator is used as an offset.
•
Enable automatic pre- or post-increment or decrement
•
Specify use of 5-bit, 9-bit, or 16-bit signed offsets.
Table 2-3. Summary of Indexed Operations
Postbyte
Code (xb)
Source
Code
Syntax
Comments
,r
n,r
–n,r
5-bit constant offset n = –16 to +15
rr can specify X, Y, SP, or PC
111rr0zs
n,r
–n,r
Constant offset (9- or 16-bit signed)
z-0 = 9-bit with sign in LSB of postbyte(s)
1 = 16-bit
if z = s = 1, 16-bit offset indexed-indirect (see below)
rr can specify X, Y, SP, or PC
111rr011
[n,r]
16-bit offset indexed-indirect
rr can specify X, Y, SP, or PC
rr1pnnnn
n,–r n,+r
n,r– n,r+
Auto pre-decrement/increment or Auto postdecrement/increment;
p = pre-(0) or post-(1), n = –8 to –1, +1 to +8
rr can specify X, Y, or SP (PC not a valid choice)
111rr1aa
A,r
B,r
D,r
Accumulator offset (unsigned 8-bit or 16-bit)
aa-00 = A
01 = B
10 = D (16-bit)
11 = see accumulator D offset indexed-indirect
rr can specify X, Y, SP, or PC
111rr111
[D,r]
Accumulator D offset indexed-indirect
rr can specify X, Y, SP, or PC
rr0nnnnn
Technical Data
34
MC68HC912DG128 — Rev 3.0
Central Processing Unit
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Central Processing Unit
Opcodes and Operands
2.7 Opcodes and Operands
The CPU12 uses 8-bit opcodes. Each opcode identifies a particular
instruction and associated addressing mode to the CPU. Several
opcodes are required to provide each instruction with a range of
addressing capabilities.
Freescale Semiconductor, Inc...
Only 256 opcodes would be available if the range of values were
restricted to the number that can be represented by 8-bit binary
numbers. To expand the number of opcodes, a second page is added to
the opcode map. Opcodes on the second page are preceded by an
additional byte with the value $18.
To provide additional addressing flexibility, opcodes can also be
followed by a postbyte or extension bytes. Postbytes implement certain
forms of indexed addressing, transfers, exchanges, and loop primitives.
Extension bytes contain additional program information such as
addresses, offsets, and immediate data.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Central Processing Unit
For More Information On This Product,
Go to: www.freescale.com
35
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Central Processing Unit
Technical Data
36
MC68HC912DG128 — Rev 3.0
Central Processing Unit
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Section 3. Pinout and Signal Descriptions
3.1 Contents
3.2
Pin Assignments in 112-pin QFP . . . . . . . . . . . . . . . . . . . . . . . 37
3.3
Power Supply Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .40
3.4
Signal Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3.5
Port Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 51
3.2 Pin Assignments in 112-pin QFP
The MC68HC912DG128 is available in a 112-pin thin quad flat pack
(TQFP). Most pins perform two or more functions, as described in the
Signal Descriptions. Figure 3-2 shows pin assignments. In expanded
narrow modes the lower byte data is multiplexed with higher byte data
through pins 57-64.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
37
Freescale Semiconductor, Inc.
84
83
82
81
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
MC68HC912DG128
112TQFP
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
PAD17/AN17
PAD07/AN07
PAD16/AN16
PAD06/AN06
PAD15/AN15
PAD05/AN05
PAD14/AN14
PAD04/AN04
PAD13/AN13
PAD03/AN03
PAD12/AN12
PAD02/AN02
PAD11/AN11
PAD01/AN01
PAD10/AN10
PAD00/AN00
VRL0
VRH0
VSS
VDD
PA7/ADDR15/DATA15/DATA7
PA6/ADDR14/DATA14/DATA6
PA5/ADDR13/DATA13/DATA5
PA4/ADDR12/DATA12/DATA4
PA3/ADDR11/DATA11/DATA3
PA2/ADDR10/DATA10/DATA2
PA1/ADDR9/DATA9/DATA1
PA0/ADDR8/DATA8/DATA0
ADDR5/DATA5/PB5
ADDR6/DATA6/PB6
ADDR7/DATA7/PB7
KWH7/PH7
KWH6/PH6
KWH5/PH5
KWH4/PH4
DBE/CAL/PE7
MODB/IPIPE1/PE6
MODA/IPIPE0/PE5
ECLK/PE4
VSSX
VSTBY
VDDX
VDDPLL
XFC
VSSPLL
RESET
EXTAL
XTAL
KWH3/PH3
KWH2/PH2
KWH1/PH1
KWH0/PH0
LSTRB/TAGLO/PE3
R/W/PE2
IRQ/PE1
XIRQ/PE0
Freescale Semiconductor, Inc...
PW2/PP2
PW1/PP1
PW0/PP0
IOC0/PT0
IOC1/PT1
IOC2/PT2
IOC3/PT3
KWJ7/PJ7
KWJ6/PJ6
KWJ5/PJ5
KWJ4/PJ4
VDD
PK3
VSS
IOC4/PT4
IOC5/PT5
IOC6/PT6
IOC7/PT7
KWJ3/PJ3
KWJ2/PJ2
KWJ1/PJ1
KWJ0/PJ0
SMODN/TAGHI/BKGD
ADDR0/DATA0/PB0
ADDR1/DATA1/PB1
ADDR2/DATA2/PB2
ADDR3/DATA3/PB3
ADDR4/DATA4/PB4
112
111
110
109
108
107
106
105
104
103
102
101
100
99
98
97
96
95
94
93
92
91
90
89
88
87
86
85
PP3/PW3
PK0/PIX0
PK1/PIX1
PK2/PIX2
PK7/ECS
VDDX
VSSX
RxCAN0
TxCAN0
RxCAN1
TxCAN1
PIB4
PIB5
PIB6/SDA
PIB7/SCL
VFP*
PS7/SS
PS6/SCK
PS5/SDO/MOSI
PS4/SDI/MISO
PS3/TxD1
PS2/RxD1
PS1/TxD0
PS0/RxD0
VSSA
VRL1
VRH1
VDDA
Pinout and Signal Descriptions
Figure 3-1. MC68HC912DG128 Pin Assignments in 112-pin QFP
Technical Data
38
MC68HC912DG128 — Rev 3.0
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pinout and Signal Descriptions
Pin Assignments in 112-pin QFP
0.20 T L-M N
4X
PIN 1
IDENT
0.20 T L-M N
4X 28 TIPS
112
J1
85
4X
P
J1
1
CL
84
VIEW Y
108X
X
X=L, M OR N
G
VIEW Y
B
L
V
M
B1
28
AA
J
V1
57
29
F
D
56
0.13
N
M
T
BASE
METAL
L-M N
SECTION J1-J1
ROTATED 90 ° COUNTERCLOCKWISE
A1
S1
A
S
C2
C
VIEW AB
θ2
0.050
0.10 T
112X
SEATING
PLANE
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ASME Y14.5M, 1994.
2. DIMENSIONS IN MILLIMETERS.
3. DATUMS L, M AND N TO BE DETERMINED AT
SEATING PLANE, DATUM T.
4. DIMENSIONS S AND V TO BE DETERMINED AT
SEATING PLANE, DATUM T.
5. DIMENSIONS A AND B DO NOT INCLUDE
MOLD PROTRUSION. ALLOWABLE
PROTRUSION IS 0.25 PER SIDE. DIMENSIONS
A AND B INCLUDE MOLD MISMATCH.
6. DIMENSION D DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL NOT CAUSE THE D
DIMENSION TO EXCEED 0.46.
θ3
T
θ
R
R2
R
0.25
R1
GAGE PLANE
(K)
C1
θ1
E
(Y)
(Z)
VIEW AB
DIM
A
A1
B
B1
C
C1
C2
D
E
F
G
J
K
P
R1
R2
S
S1
V
V1
Y
Z
AA
θ
θ1
θ2
θ3
MILLIMETERS
MIN
MAX
20.000 BSC
10.000 BSC
20.000 BSC
10.000 BSC
--1.600
0.050
0.150
1.350
1.450
0.270
0.370
0.450
0.750
0.270
0.330
0.650 BSC
0.090
0.170
0.500 REF
0.325 BSC
0.100
0.200
0.100
0.200
22.000 BSC
11.000 BSC
22.000 BSC
11.000 BSC
0.250 REF
1.000 REF
0.090
0.160
8 °
0°
7 °
3 °
13 °
11 °
11 °
13 °
Figure 3-2. 112-pin QFP Mechanical Dimensions (case no. 987)
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
39
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pinout and Signal Descriptions
3.3 Power Supply Pins
Power and ground pins are described below and summarized in Table
3-1.
3.3.1 Internal Power (VDD) and Ground (VSS)
Power is supplied to the MCU through VDD and VSS. Because fast signal
transitions place high, short-duration current demands on the power
supply, use bypass capacitors with high-frequency characteristics and
place them as close to the MCU as possible. Bypass requirements
depend on how heavily the MCU pins are loaded.
3.3.2 External Power (VDDX) and Ground (VSSX)
External power and ground for I/O drivers. Because fast signal
transitions place high, short-duration current demands on the power
supply, use bypass capacitors with high-frequency characteristics and
place them as close to the MCU as possible. Bypass requirements
depend on how heavily the MCU pins are loaded.
3.3.3 VDDA, VSSA
Provides operating voltage and ground for the analog-to-digital
converter. This allows the supply voltage to the ATD to be bypassed
independently. Connecting VDDA to VDD if the ATD modules are not
used will not result in an increase of power consumption.
3.3.4 Analog to Digital Reference Voltages (VRH, VRL)
VRH0, VRL0: reference voltage high and low for ATD converter 0.
VRH1, VRL1: reference voltage high and low for ATD converter 1.
If the ATD modules are not used, leaving VRH connected to VDD will not
result in an increase of power consumption.
Technical Data
40
MC68HC912DG128 — Rev 3.0
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pinout and Signal Descriptions
Power Supply Pins
3.3.5 VDDPLL, VSSPLL
Provides operating voltage and ground for the Phase-Locked Loop. This
allows the supply voltage to the PLL to be bypassed independently.
NOTE:
The VSSPLL pin should always be grounded even if the PLL is not used.
The VDDPLL pin should not be left floating. It is recommended to
connect the VDDPLL pin to ground if the PLL is not used.
3.3.6 XFC
PLL loop filter. Please see Appendix: CGM Practical Aspects for
information on how to calculate PLL loop filter elements. Any current
leakage on this pin must be avoided.
VDDPLL
C0
MCU
R0
Cp
XFC
Figure 3-3. PLL Loop FIlter Connections
If VDDPLL is connected to VSS (this is normal case), then the XFC pin
should either be left floating or connected to VSS (never to VDD). If
VDDPLL is tied to VDD but the PLL is switched off (PLLON bit cleared),
then the XFC pin should be connected preferably to VDDPLL (i.e. ready
for VCO minimum frequency).
3.3.7 VFP
Flash EEPROM program/erase voltage and supply voltage during
normal operation.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
41
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pinout and Signal Descriptions
3.3.8 VSTBY
Stand-by voltage supply to static RAM. Used to maintain the contents of
RAM with minimal power when the rest of the chip is powered down.
Table 3-1. Power and Ground Connection Summary
VDD
Pin Number
112-pin QFP
12, 65
VSS
14, 66
VDDX
42, 107
VSSX
40, 106
VDDA
85
VSSA
88
VRH1
86
VRL1
87
VRH0
67
VRL0
68
VDDPLL
43
VSSPLL
45
VFP
97
VSTBY
41
Mnemonic
Description
Internal power and ground.
External power and ground, supply to pin drivers.
Operating voltage and ground for the analog-to-digital converter, allows the
supply voltage to the A/D to be bypassed independently.
Reference voltages for the analog-to-digital converter 1
Reference voltages for the analog-to-digital converter 0.
Provides operating voltage and ground for the Phase-Locked Loop. This allows
the supply voltage to the PLL to be bypassed independently.
Program/erase voltage for the Flash EEPROM and required supply for normal
operation.
Stand-by voltage supply to maintain the contents of RAM with minimal power
when the rest of the chip is powered down.
3.4 Signal Descriptions
3.4.1 Crystal Driver and External Clock Input (XTAL, EXTAL)
These pins provide the interface for either a crystal or a CMOS
compatible clock to control the internal clock generator circuitry. Out of
reset the frequency applied to EXTAL is twice the desired E–clock rate.
All the device clocks are derived from the EXTAL input frequency.
NOTE:
CRYSTAL CIRCUIT IS CHANGED FROM STANDARD.
Technical Data
42
MC68HC912DG128 — Rev 3.0
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Pinout and Signal Descriptions
Signal Descriptions
NOTE:
The internal return path for the oscillator is the VSSPLL pin. Therefore it
is recommended to connect the common node of the resonator and the
capacitor directly to the VSSPLL pin.
2 x E crystal or ceramic resonator
EXTAL
MCU
C1
C2
Freescale Semiconductor, Inc...
XTAL
Figure 3-4. Common Crystal Connections
NOTE:
When selecting a crystal, it is recommended to use one with the lowest
possible frequency in order to minimise EMC emissions.
2xE
CMOS-COMPATIBLE
EXTERNAL OSCILLATOR
EXTAL
MCU
XTAL
NC
Figure 3-5. External Oscillator Connections
XTAL is the crystal output.The XTAL pin must be left unterminated when
an external CMOS compatible clock input is connected to the EXTAL
pin. The XTAL output is normally intended to drive only a crystal. The
XTAL output can be buffered with a high-impedance buffer to drive the
EXTAL input of another device.
In all cases take extra care in the circuit board layout around the
oscillator pins. Load capacitances in the oscillator circuits include all
stray layout capacitances. Refer to Figure 3-4 and Figure 3-5 for
diagrams of oscillator circuits.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
43
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pinout and Signal Descriptions
3.4.2 E-Clock Output (ECLK)
ECLK is the output connection for the internal bus clock. It is used to
demultiplex the address and data in expanded modes and is used as a
timing reference. ECLK frequency is equal to 1/2 the crystal frequency
out of reset. The E-clock output is turned off in single chip user mode to
reduce the effects of RFI. It can be turned on if necessary. In special
single-chip mode, the E-clock is turned ON at reset and can be turned
OFF. In special peripheral mode the E-clock is an input to the MCU. All
clocks, including the E clock, are halted when the MCU is in STOP
mode. It is possible to configure the MCU to interface to slow external
memory. ECLK can be stretched for such accesses.
3.4.3 Reset (RESET)
An active low bidirectional control signal, RESET, acts as an input to
initialize the MCU to a known start-up state. It also acts as an open-drain
output to indicate that an internal failure has been detected in either the
clock monitor or COP watchdog circuit. The MCU goes into reset
asynchronously and comes out of reset synchronously. This allows the
part to reach a proper reset state even if the clocks have failed, while
allowing synchronized operation when starting out of reset.
It is important to use an external low-voltage reset circuit (such as
MC34064 or MC34164) to prevent corruption of RAM or EEPROM due
to power transitions.
The reset sequence is initiated by any of the following events:
•
Power-on-reset (POR)
•
COP watchdog enabled and watchdog timer times out
•
Clock monitor enabled and Clock monitor detects slow or stopped
clock
•
User applies a low level to the reset pin
External circuitry connected to the reset pin should not include a large
capacitance that would interfere with the ability of this signal to rise to a
valid logic one within nine bus cycles after the low drive is released.
Technical Data
44
MC68HC912DG128 — Rev 3.0
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pinout and Signal Descriptions
Signal Descriptions
Upon detection of any reset, an internal circuit drives the reset pin low
and a clocked reset sequence controls when the MCU can begin normal
processing. In the case of POR or a clock monitor error, a 4096 cycle
oscillator startup delay is imposed before the reset recovery sequence
starts (reset is driven low throughout this 4096 cycle delay). The internal
reset recovery sequence then drives reset low for 16 to 17 cycles and
releases the drive to allow reset to rise. Nine cycles later this circuit
samples the reset pin to see if it has risen to a logic one level. If reset is
low at this point, the reset is assumed to be coming from an external
request and the internally latched states of the COP time-out and clock
monitor failure are cleared so the normal reset vector ($FFFE:FFFF) is
taken when reset is finally released. If reset is high after this nine cycle
delay, the reset source is tentatively assumed to be either a COP failure
or a clock monitor fail. If the internally latched state of the clock monitor
fail circuit is true, processing begins by fetching the clock monitor vector
($FFFC:FFFD). If no clock monitor failure is indicated, and the latched
state of the COP time-out is true, processing begins by fetching the COP
vector ($FFFA:FFFB). If neither clock monitor fail nor COP time-out are
pending, processing begins by fetching the normal reset vector
($FFFE:FFFF).
3.4.4 Maskable Interrupt Request (IRQ)
The IRQ input provides a means of applying asynchronous interrupt
requests to the MCU. Either falling edge-sensitive triggering or levelsensitive triggering is program selectable (INTCR register). IRQ is
always enabled and configured to level-sensitive triggering at reset. It
can be disabled by clearing the IRQEN bit (INTCR register). When the
MCU is reset, the IRQ function is masked in the condition code register.
This pin is always an input and can always be read. There is an active
pull-up on this pin while in reset and immediately out of reset. The pullup can be turned off by clearing PUPE in the PUCR register.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
45
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pinout and Signal Descriptions
3.4.5 Nonmaskable Interrupt (XIRQ)
The XIRQ input provides a means of requesting a nonmaskable interrupt
after reset initialization. During reset, the X bit in the condition code
register (CCR) is set and any interrupt is masked until MCU software
enables it. Because the XIRQ input is level sensitive, it can be connected
to a multiple-source wired-OR network. This pin is always an input and
can always be read. There is an active pull-up on this pin while in reset
and immediately out of reset. The pull-up can be turned off by clearing
PUPE in the PUCR register. XIRQ is often used as a power loss detect
interrupt.
Whenever XIRQ or IRQ are used with multiple interrupt sources (IRQ
must be configured for level-sensitive operation if there is more than one
source of IRQ interrupt), each source must drive the interrupt input with
an open-drain type of driver to avoid contention between outputs. There
must also be an interlock mechanism at each interrupt source so that the
source holds the interrupt line low until the MCU recognizes and
acknowledges the interrupt request. If the interrupt line is held low, the
MCU will recognize another interrupt as soon as the interrupt mask bit in
the MCU is cleared (normally upon return from an interrupt).
3.4.6 Mode Select (SMODN, MODA, and MODB)
The state of these pins during reset determine the MCU operating mode.
After reset, MODA and MODB can be configured as instruction queue
tracking signals IPIPE0 and IPIPE1 in expanded modes. MODA and
MODB have active pull-downs during reset.
The SMODN pin has an active pull-up when configured as an input. This
pin can be used as BKGD or TAGHI after reset.
3.4.7 Single-Wire Background Mode Pin (BKGD)
The BKGD pin receives and transmits serial background debugging
commands. A special self-timing protocol is used. The BKGD pin has an
active pull-up when configured as an input; BKGD has no pull-up control.
Refer to Development Support.
Technical Data
46
MC68HC912DG128 — Rev 3.0
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pinout and Signal Descriptions
Signal Descriptions
3.4.8 External Address and Data Buses (ADDR[15:0] and DATA[15:0])
External bus pins share functions with general-purpose I/O ports A and
B. In single-chip operating modes, the pins can be used for I/O; in
expanded modes, the pins are used for the external buses.
In expanded wide mode, ports A and B are used for multiplexed 16-bit
data and address buses. PA[7:0] correspond to
ADDR[15:8]/DATA[15:8]; PB[7:0] correspond to ADDR[7:0]/DATA[7:0].
In expanded narrow mode, ports A and B are used for the16-bit address
bus, and an 8-bit data bus is multiplexed with the most significant half of
the address bus on port A. In this mode, 16-bit data is handled as two
back-to-back bus cycles, one for the high byte followed by one for the
low byte. PA[7:0] correspond to ADDR[15:8] and to DATA[15:8] or
DATA[7:0], depending on the bus cycle. The state of the address pins
should be latched at the rising edge of E. To allow for maximum address
setup time at external devices, a transparent latch should be used.
3.4.9 Read/Write (R/W)
In all modes this pin can be used as a general-purpose I/O and is an
input with an active pull-up out of reset. If the read/write function is
required it should be enabled by setting the RDWE bit in the PEAR
register. External writes will not be possible until enabled.
3.4.10 Low-Byte Strobe (LSTRB)
In all modes this pin can be used as a general-purpose I/O and is an
input with an active pull-up out of reset. If the strobe function is required,
it should be enabled by setting the LSTRE bit in the PEAR register. This
signal is used in write operations and so external low byte writes will not
be possible until this function is enabled. This pin is also used as TAGLO
in Special Expanded modes and is multiplexed with the LSTRB function.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
47
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pinout and Signal Descriptions
3.4.11 Instruction Queue Tracking Signals (IPIPE1 and IPIPE0)
These signals are used to track the state of the internal instruction
execution queue. Execution state is time-multiplexed on the two signals.
Refer to Development Support.
3.4.12 Data Bus Enable (DBE)
The DBE pin (PE7) is an active low signal that will be asserted low during
E-clock high time. DBE provides separation between output of a
multiplexed address and the input of data. When an external address is
stretched, DBE is asserted during what would be the last quarter cycle
of the last E-clock cycle of stretch. In expanded modes this pin is used
to enable the drive control of external buses during external reads. Use
of the DBE is controlled by the NDBE bit in the PEAR register. DBE is
enabled out of reset in expanded modes. This pin has an active pull-up
during and after reset in single chip modes.
3.4.13 Inverted E clock (ECLK)
The ECLK pin (PE7) can be used to latch the address for demultiplexing. It has the same behavior as the ECLK, except is inverted.
In expanded modes this pin is used to enable the drive control of external
buses during external reads. Use of the ECLK is controlled by the NDBE
and DBENE bits in the PEAR register.
3.4.14 Calibration reference (CAL)
The CAL pin (PE7) is the output of the Slow Mode programmable clock
divider, SLWCLK, and is used as a calibration reference. The SLWCLK
frequency is equal to the crystal frequency out of reset and always has
a 50% duty. If the DBE function is enabled it will override the enabled
CAL output. The CAL pin output is disabled by clearing CALE bit in the
PEAR register.
Technical Data
48
MC68HC912DG128 — Rev 3.0
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pinout and Signal Descriptions
Signal Descriptions
3.4.15 Clock generation module test (CGMTST)
The CGMTST pin (PE6) is the output of the clocks tested when CGMTE
bit is set in PEAR register. The PIPOE bit must be cleared for the clocks
to be tested.
Table 3-2. Signal Description Summary
Pin Name
Shared
port
Pin
Number
Description
112-pin
EXTAL
-
47
XTAL
-
48
RESET
-
46
ADDR[7:0]
DATA[7:0]
PB[7:0]
31–24
ADDR[15:8]
DATA[15:8]
PA[7:0]
64–57
DBE
PE7
36
ECLK
PE7
36
Inverted E clock used to latch the address.
Crystal driver and external clock input pins. On reset all the device clocks
are derived from the EXTAL input frequency. XTAL is the crystal output.
An active low bidirectional control signal, RESET acts as an input to
initialize the MCU to a known start-up state, and an output when COP or
clock monitor causes a reset.
External bus pins share function with general-purpose I/O ports A and B.
In single chip modes, the pins can be used for I/O. In expanded modes,
the pins are used for the external buses.
Data bus control and, in expanded mode, enables the drive control of
external buses during external reads.
CAL
PE7
36
CAL is the output of the Slow Mode programmable clock divider,
SLWCLK, and is used as a calibration reference for functions such as
time of day. It is overridden when DBE function is enabled. It always has
a 50% duty.
CGMTST
PE6
37
Clock generation module test output.
MODB/
IPIPE1,
MODA/
IPIPE0
PE6, PE5
37, 38
State of mode select pins during reset determine the initial operating
mode of the MCU. After reset, MODB and MODA can be configured as
instruction queue tracking signals IPIPE1 and IPIPE0 or as generalpurpose I/O pins.
ECLK
PE4
39
E Clock is the output connection for the external bus clock. ECLK is used
as a timing reference and for address demultiplexing.
LSTRB/
TAGLO
PE3
53
Low byte strobe (0 = low byte valid), in all modes this pin can be used as
I/O. The low strobe function is the exclusive-NOR of A0 and the internal
SZ8 signal. (The SZ8 internal signal indicates the size 16/8 access.) Pin
function TAGLO used in instruction tagging. See Development Support.
R/W
PE2
54
Indicates direction of data on expansion bus. Shares function with
general-purpose I/O. Read/write in expanded modes.
55
Maskable interrupt request input provides a means of applying
asynchronous interrupt requests to the MCU. Either falling edgesensitive triggering or level-sensitive triggering is program selectable
(INTCR register).
IRQ
PE1
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
49
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pinout and Signal Descriptions
Table 3-2. Signal Description Summary
Pin Name
XIRQ
Shared
port
PE0
Pin
Number
Description
112-pin
56
Provides a means of requesting asynchronous nonmaskable interrupt
requests after reset initialization
During reset, this pin determines special or normal operating mode. After
reset, single-wire background interface pin is dedicated to the
background debug function. Pin function TAGHI used in instruction
tagging. See Development Support.
SMODN/
BKGD/
TAGHI
-
23
IX[2:0]
PK[2:0]
109-111
ECS
PK7
108
PW[3:0]
PP[3:0]
112, 1–3
SS
PS7
96
Slave select output for SPI master mode, input for slave mode or master
mode.
SCK
PS6
95
Serial clock for SPI system.
SDO/MOSI
PS5
94
Master out/slave in pin for serial peripheral interface
Page Index register emulation outputs.
Emulation Chip select.
Pulse Width Modulator channel outputs.
SDI/MISO
PS4
93
Master in/slave out pin for serial peripheral interface
TxD1
PS3
92
SCI1 transmit pin
RxD1
PS2
91
SCI1 receive pin
TxD0
PS1
90
SCI0 transmit pin
RxD0
PS0
89
SCI0 receive pin
IOC[7:0]
PT[7:0]
18–15, 7–4
Pins used for input capture and output compare in the timer and pulse
accumulator subsystem.
AN1[7:0]
84/82/80/7
PAD1[7:0] 8/76/74/72/ Analog inputs for the analog-to-digital conversion module 1
70
AN0[7:0]
83/81/79/7
PAD0[7:0] 7/75/73/71/ Analog inputs for the analog-to-digital conversion module 0
69
TxCAN1
-
102
MSCAN1 transmit pin
RxCAN1
-
103
MSCAN1 receive pin
TxCAN0
-
104
MSCAN0 transmit pin
RxCAN0
-
105
MSCAN0 receive pin
SCL
PIB7
98
I2C bus serial clock line pin
SDA
PIB6
99
I2C bus serial data line pin
KWJ[7:0]
PJ[7:0]
8–11,
19–22
Key wake-up and general purpose I/O; can cause an interrupt when an
input transitions from high to low or from low to high (KWPJ).
KWH[7:0]
PH[7:0]
32–35,
49–52
Key wake-up and general purpose I/O; can cause an interrupt when an
input transitions from high to low or from low to high (KWPH).
Technical Data
50
MC68HC912DG128 — Rev 3.0
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pinout and Signal Descriptions
Port Signals
3.5 Port Signals
The MC68HC912DG128 incorporates eleven ports which are used to
control and access the various device subsystems. When not used for
these purposes, port pins may be used for general-purpose I/O. In
addition to the pins described below, each port consists of a data register
which can be read and written at any time, and, with the exception of port
AD0, port AD1, PE[1:0], RxCAN and TxCAN, a data direction register
which controls the direction of each pin. After reset all general purpose
I/O pins are configured as input.
3.5.1 Port A
Port A pins are used for address and data in expanded modes. In single
chip modes, the pins can be used as general purpose I/O. The port data
register is not in the address map during expanded and peripheral mode
operation. When it is in the map, port A can be read or written at anytime.
Register DDRA determines whether each port A pin is an input or output.
DDRA is not in the address map during expanded and peripheral mode
operation. Setting a bit in DDRA makes the corresponding bit in port A
an output; clearing a bit in DDRA makes the corresponding bit in port A
an input. The default reset state of DDRA is all zeros.
When the PUPA bit in the PUCR register is set, all port A input pins are
pulled-up internally by an active pull-up device. PUCR is not in the
address map in peripheral mode.
Setting the RDPA bit in register RDRIV causes all port A outputs to have
reduced drive level. RDRIV can be written once after reset. RDRIV is not
in the address map in peripheral mode. Refer to Bus Control and
Input/Output.
3.5.2 Port B
Port B pins are used for address and data in expanded modes. In single
chip modes, the pins can be used as general purpose I/O. The port data
register is not in the address map during expanded and peripheral mode
operation. When it is in the map, port B can be read or written at anytime.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
51
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pinout and Signal Descriptions
Register DDRB determines whether each port B pin is an input or output.
DDRB is not in the address map during expanded and peripheral mode
operation. Setting a bit in DDRB makes the corresponding bit in port B
an output; clearing a bit in DDRB makes the corresponding bit in port B
an input. The default reset state of DDRB is all zeros.
When the PUPB bit in the PUCR register is set, all port B input pins are
pulled-up internally by an active pull-up device. PUCR is not in the
address map in peripheral mode.
Setting the RDPB bit in register RDRIV causes all port B outputs to have
reduced drive level. RDRIV can be written once after reset. RDRIV is not
in the address map in peripheral mode. Refer to Bus Control and
Input/Output.
3.5.3 Port E
Port E pins operate differently from port A and B pins. Port E pins are
used for bus control signals and interrupt service request signals. When
a pin is not used for one of these specific functions, it can be used as
general-purpose I/O. However, two of the pins (PE[1:0]) can only be
used for input, and the states of these pins can be read in the port data
register even when they are used for IRQ and XIRQ.
The PEAR register determines pin function, and register DDRE
determines whether each pin is an input or output when it is used for
general-purpose I/O. PEAR settings override DDRE settings. Because
PE[1:0] are input-only pins, only DDRE[7:2] have effect. Setting a bit in
the DDRE register makes the corresponding bit in port E an output;
clearing a bit in the DDRE register makes the corresponding bit in port E
an input. The default reset state of DDRE is all zeros.
When the PUPE bit in the PUCR register is set, PE[7,3,2,1,0] are pulled
up. PE[7,3,2,0] are active pull-up devices. PUPCR is not in the address
map in peripheral mode.
Neither port E nor DDRE is in the map in peripheral mode; neither is in
the internal map in expanded modes with EME set.
Technical Data
52
MC68HC912DG128 — Rev 3.0
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Pinout and Signal Descriptions
Port Signals
Setting the RDPE bit in register RDRIV causes all port E outputs to have
reduced drive level. RDRIV can be written once after reset. RDRIV is not
in the address map in peripheral mode. Refer to Bus Control and
Input/Output.
3.5.4 Port H
Freescale Semiconductor, Inc...
Port H pins are used for key wake-ups that can be used with the pins
configured as inputs or outputs. The key wake-ups are triggered with
either a rising or falling edge signal (KWPH). An interrupt is generated if
the corresponding bit is enabled (KWIEH). If any of the interrupts is not
enabled, the corresponding pin can be used as a general purpose I/O
pin. Refer to I/O Ports with Key Wake-up.
Register DDRH determines whether each port H pin is an input or output.
Setting a bit in DDRH makes the corresponding bit in port H an output;
clearing a bit in DDRH makes the corresponding bit in port H an input.
The default reset state of DDRH is all zeros.
Register KWPH not only determines what type of edge the key wake ups
are triggered, but it also determines what type of resistive load is used
for port H input pins when PUPH bit is set in the PUCR register. Setting
a bit in KWPH makes the corresponding key wake up input pin trigger at
rising edges and loads a pull down in the corresponding port H input pin.
Clearing a bit in KWPH makes the corresponding key wake up input pin
trigger at falling edges and loads a pull up in the corresponding port H
input pin. The default state of KWPH is all zeros.
Setting the RDPH bit in register RDRIV causes all port H outputs to have
reduced drive level. RDRIV can be written once after reset. RDRIV is not
in the address map in peripheral mode. Refer to Bus Control and
Input/Output.
3.5.5 Port J
Port J pins are used for key wake-ups that can be used with the pins
configured as inputs or outputs. The key wake-ups are triggered with
either a rising or falling edge signal (KWPJ). An interrupt is generated if
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
53
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pinout and Signal Descriptions
the corresponding bit is enabled (KWIEJ). If any of the interrupts is not
enabled, the corresponding pin can be used as a general purpose I/O
pin. Refer to I/O Ports with Key Wake-up.
Register DDRJ determines whether each port J pin is an input or output.
Setting a bit in DDRJ makes the corresponding bit in port J an output;
clearing a bit in DDRJ makes the corresponding bit in port J an input. The
default reset state of DDRJ is all zeros.
Register KWPJ not only determines what type of edge the key wake ups
are triggered, but it also determines what type of resistive load is used
for port J input pins when PUPJ bit is set in the PUCR register. Setting a
bit in KWPJ makes the corresponding key wake up input pin trigger at
rising edges and loads a pull down in the corresponding port J input pin.
Clearing a bit in KWPJ makes the corresponding key wake up input pin
trigger at falling edges and loads a pull up in the corresponding port J
input pin. The default state of KWPJ is all zeros.
Setting the RDPJ bit in register RDRIV causes all port J outputs to have
reduced drive level. RDRIV can be written once after reset. RDRIV is not
in the address map in peripheral mode. Refer to Bus Control and
Input/Output.
3.5.6 Port K
Port K pins are used for page index emulation in expanded or peripheral
modes. When page index emulation is not enabled, EMK is not set in
MODE register, or the part is in single chip mode, these pins can be used
for general purpose I/O. Port K bit 3 is used as a general purpose I/O pin
only. The port data register is not in the address map during expanded
and peripheral mode operation with EMK set. When it is in the map, port
K can be read or written at anytime.
Register DDRK determines whether each port K pin is an input or output.
DDRK is not in the address map during expanded and peripheral mode
operation with EMK set. Setting a bit in DDRK makes the corresponding
bit in port K an output; clearing a bit in DDRK makes the corresponding
bit in port K an input. The default reset state of DDRK is all zeros.
Technical Data
54
MC68HC912DG128 — Rev 3.0
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pinout and Signal Descriptions
Port Signals
When the PUPK bit in the PUCR register is set, all port K input pins are
pulled-up internally by an active pull-up device. PUCR is not in the
address map in peripheral mode.
Setting the RDPK bit in register RDRIV causes all port K outputs to have
reduced drive level. RDRIV can be written once after reset. RDRIV is not
in the address map in peripheral mode. Refer to Bus Control and
Input/Output.
3.5.7 Port CAN1
The MSCAN1 uses two external pins, one input (RxCAN1) and one
output (TxCAN1). The TxCAN1 output pin represents the logic level on
the CAN: ‘0’ is for a dominant state, and ‘1’ is for a recessive state.
RxCAN1 is on bit 0 of Port CAN1, TxCAN1 is on bit 1.
3.5.8 Port CAN0
The MSCAN0 uses two external pins, one input (RxCAN0) and one
output (TxCAN0). The TxCAN0 output pin represents the logic level on
the CAN: ‘0’ is for a dominant state, and ‘1’ is for a recessive state.
RxCAN0 is on bit 0 of Port CAN0, TxCAN0 is on bit 1.
3.5.9 Port IB
Bidirectional pins to IIC bus interface subsystem. The IIC bus interface
uses a Serial Data line (SDA) and Serial Clock line (SCL) for data
transfer. The pins are connected to a positive voltage supply via a pull
up resistor. The pull ups can be enabled internally or connected
externally. The output stages have open drain outputs in order to
perform the wired-AND function. When the IIC is disabled the pins can
be used as general purpose I/O pins. SCL is on bit 7 of Port IB and SDA
is on bit 6. The remaining pins of Port IB (PIB[5:4]) are controlled by
registers in the IIC address space.
Register DDRIB determines pin direction of port IB when used for
general-purpose I/O. When DDRIB bits are set, the corresponding pin is
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
55
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pinout and Signal Descriptions
configured for output. On reset the DDRIB bits are cleared and the
corresponding pin is configured for input.
When the PUPIB bit in the IBPURD register is set, all input pins are
pulled up internally by an active pull-up device. Pull-ups are disabled
after reset, except for input ports 0 through 3, which are always on
regardless of PUPIB bit.
Setting the RDPIB bit in the IBPURD register configures all port IB
outputs to have reduced drive levels. Levels are at normal drive
capability after reset. The IBPURD register can be read or written
anytime after reset. Refer to section Inter-IC Bus.
3.5.10 Port AD1
This port is an analog input interface to the analog-to-digital subsystem
and used for general-purpose input. When analog-to-digital functions
are not enabled, the port has eight general-purpose input pins,
PAD1[7:0]. The ADPU bit in the ATD1CTL2 register enables the A/D
function.
Port AD1 pins are inputs; no data direction register is associated with this
port. The port has no resistive input loads and no reduced drive controls.
Refer to MSCAN Controller.
3.5.11 Port AD0
This port is an analog input interface to the analog-to-digital subsystem
and used for general-purpose input. When analog-to-digital functions are
not enabled, the port has eight general-purpose input pins, PAD0[7:0].
The ADPU bit in the ATD0CTL2 register enables the A/D function.
Port AD0 pins are inputs; no data direction register is associated with this
port. The port has no resistive input loads and no reduced drive controls.
Refer to MSCAN Controller.
Technical Data
56
MC68HC912DG128 — Rev 3.0
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pinout and Signal Descriptions
Port Signals
3.5.12 Port P
The four pulse-width modulation channel outputs share general-purpose
port P pins. The PWM function is enabled with the PWEN register.
Enabling PWM pins takes precedence over the general-purpose port.
When pulse-width modulation is not in use, the port pins may be used for
general-purpose I/O.
Register DDRP determines pin direction of port P when used for
general-purpose I/O. When DDRP bits are set, the corresponding pin is
configured for output. On reset the DDRP bits are cleared and the
corresponding pin is configured for input.
When the PUPP bit in the PWCTL register is set, all input pins are pulled
up internally by an active pull-up device. Pull-ups are disabled after reset.
Setting the RDPP bit in the PWCTL register configures all port P outputs
to have reduced drive levels. Levels are at normal drive capability after
reset. The PWCTL register can be read or written anytime after reset.
Refer to Pulse Width Modulator.
3.5.13 Port S
Port S is the 8-bit interface to the standard serial interface consisting of
the two serial communications interfaces (SCI1 and SCI0) and the serial
peripheral interface (SPI) subsystems. Port S pins are available for
general-purpose I/O when standard serial functions are not enabled.
Port S pins serve several functions depending on the various internal
control registers. If WOMS bit in the SC0CR1register is set, the Pchannel drivers of the output buffers are disabled (wire-or mode) for pins
0 through 3. If SWOM bit in the SP0CR1 register is set, the P-channel
drivers of the output buffers are disabled (wire-or mode) for pins 4
through 7. The open drain control affects both the serial and the generalpurpose outputs. If the RDPS bit in the SP0CR2 register is set, Port S
pin drive capabilities are reduced. If PUPS bit in the SP0CR2 register is
set, a pull-up device is activated for each port S pin programmed as a
general purpose input. If the pin is programmed as a general-purpose
output, the pull-up is disconnected from the pin regardless of the state of
PUPS bit. See Multiple Serial Interface.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
57
Freescale Semiconductor, Inc.
Pinout and Signal Descriptions
3.5.14 Port T
This port provides eight general-purpose I/O pins when not enabled for
input capture and output compare in the timer and pulse accumulator
subsystem. The TEN bit in the TSCR register enables the timer function.
The pulse accumulator subsystem is enabled with the PAEN bit in the
PACTL register.
Freescale Semiconductor, Inc...
Register DDRT determines pin direction of port T when used for generalpurpose I/O. When DDRT bits are set, the corresponding pin is
configured for output. On reset the DDRT bits are cleared and the
corresponding pin is configured for input.
When the PUPT bit in the TMSK2 register is set, all input pins are pulled
up internally by an active pull-up device. Pull-ups are disabled after
reset.
Setting the RDPT bit in the TMSK2 register configures all port T outputs
to have reduced drive levels. Levels are at normal drive capability after
reset. The TMSK2 register can be read or written anytime after reset
Refer to Enhanced Capture Timer.
Technical Data
58
MC68HC912DG128 — Rev 3.0
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pinout and Signal Descriptions
Port Signals
Table 3-3. Port Description Summary
Pin Numbers
Port Name
112-pin
Port A
PA[7:0]
64-57
Port B
PB[7:0]
31–24
Port AD1
PAD1[7:0]
Port AD0
PAD0[7:0]
Port CAN1
PCAN1[1:0]
Port CAN0
PCAN0[1:0]
84/82/80/78/7
6/74/72/70
83/81/79/77/7
5/73/71/69
102–103
104–105
Port IB
PIB[7:4]
98–101
Port IB
PIB[3:2]
102–103
Port E
PE[7:0]
36–39, 53–56
Port K
PK[7,3:0]
Port P
PP[3:0]
Port S
PS[7:0]
Port T
PT[7:0]
13,
108-111
112,
1–3
96–89
18–15, 7–4
Data Direction
Register
(Address)
In/Out
DDRA ($0002)
In/Out
DDRB ($0003)
Description
Port A and port B pins are used for address and data in
expanded modes. The port data registers are not in the
address map during expanded and peripheral mode
operation. When in the map, port A and port B can be
read or written any time.
DDRA and DDRB are not in the address map in expanded
or peripheral modes.
In
Analog-to-digital converter 1 and general-purpose I/O.
In
Analog-to-digital converter 0 and general-purpose I/O.
PCAN1[1] Out
PCAN1[0] In
PCAN0[1] Out
PCAN0[0] In
PCAN1[1:0] are used with the MSCAN1 module and
cannot be used as general purpose I/O.
PCAN0[1:0] are used with the MSCAN0 module and
cannot be used as general purpose I/O.
In/Out
DDRIB ($00E7)
General purpose I/O. PIB[7:6] are used with the I-Bus
module when enabled.
In/Out
DDRIB ($00E7)
PE[1:0] In
PE[7:2] In/Out
DDRE ($0009)
In/Out
DDRK ($00FD)
In/Out
DDRP ($0057)
In/Out
DDRS ($00D7)
In/Out
DDRT ($00AF)
General purpose I/O
Mode selection, bus control signals and interrupt service
request signals; or general-purpose I/O.
Page index emulation signals in expanded or peripheral
mode or general-purpose I/O.
General-purpose I/O. PP[3:0] are used with the pulse-width
modulator when enabled.
Serial communications interfaces 1 and 0 and serial
peripheral interface subsystems; or general-purpose I/O.
General-purpose I/O when not enabled for input capture
and output compare in the timer and pulse accumulator
subsystem.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
59
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pinout and Signal Descriptions
3.5.15 Port Pull-Up Pull-Down and Reduced Drive
MCU ports can be configured for internal pull-up. To reduce power
consumption and RFI, the pin output drivers can be configured to
operate at a reduced drive level. Reduced drive causes a slight increase
in transition time depending on loading and should be used only for ports
which have a light loading. Table 3-4 summarizes the port pull-up/pulldown default status and controls.
Table 3-4. Port Pull-Up, Pull-Down and Reduced Drive Summary
Enable Bit
Port
Resistive
Name
Input Loads
Port A
Pull-up
Port B
Pull-up
Port E:
PE7, PE[3:2]
Pull-up
PE[1:0]
Pull-up
PE[6:4]
None
Pull-up or
Port H
Pull-down
Pull-up or
Port J
Pull-down
Port K
Pull-up
Port P
Pull-up
Port S
Pull-up
Port T
Pull-up
Port IB[7:4]
Pull-up
Port IB[3:2]
Pull-up
Port AD0
None
Port AD1
None
Port CAN1[1]
None
Port CAN1[0]
Pull-up
Port CAN0[1]
None
Port CAN0[0]
Pull-up
Register
(Address)
PUCR ($000C)
PUCR ($000C)
PUPA
PUPB
Reset
State
Disabled
Disabled
PUPE
PUPE
Enabled
Enabled
Bit Name
PUCR ($000C)
PUCR ($000C)
—
Reduced Drive Control Bit
Register
Reset
Bit Name
(Address)
State
RDRIV ($000D)
RDPA
Full drive
RDRIV ($000D)
RDPB
Full drive
RDRIV ($000D)
Full drive
RDRIV ($000D)
RDPE
—
RDPE
PUCR ($000C)
PUPH
Disabled
RDRIV ($000D)
RDPH
Full drive
PUCR ($000C)
PUPJ
Disabled
RDRIV ($000D)
RDPJ
Full drive
RDRIV ($000D)
PWCTL ($0054)
SP0CR2 ($00D1)
TMSK2 ($008D)
IBPURD ($00E5)
IBPURD ($00E5)
RDPK
RDPP
RDPS
TDRB
RDPIB
RDPIB
—
—
—
—
—
—
Full drive
Full drive
Full drive
Full drive
Full drive
Full drive
PUCR ($000C)
PUPK
Disabled
PWCTL ($0054)
PUPP
Disabled
SP0CR2 ($00D1)
PUPS
Enabled
TMSK2 ($008D)
TPU
Disabled
IBPURD ($00E5)
PUPIB Disabled
Always enabled when pins are input
—
—
—
Always enabled
—
Always enabled
Technical Data
60
Full drive
MC68HC912DG128 — Rev 3.0
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Pinout and Signal Descriptions
Technical Data
61
MC68HC912DG128 — Rev 3.0
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Pinout and Signal Descriptions
Technical Data
62
MC68HC912DG128 — Rev 3.0
Pinout and Signal Descriptions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Section 4. Registers
4.1 Contents
4.2
Register Block. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63
4.2 Register Block
The register block can be mapped to any 2K byte boundary within the
standard 64K byte address space by manipulating bits REG[15:11] in
the INITRG register. INITRG establishes the upper five bits of the
register block’s 16-bit address. The register block occupies the first 1K
byte of the 2K byte block. Default addressing (after reset) is indicated in
the table below. For additional information refer to General Description.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Registers
For More Information On This Product,
Go to: www.freescale.com
63
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Registers
Address
Bit 7
6
5
4
3
2
1
Bit 0
Name
$0000
PA7
PA6
PA5
PA4
PA3
PA2
PA1
PA0
PORTA(1)
$0001
PB7
PB6
PB5
PB4
PB3
PB2
PB1
PB0
PORTB(1)
$0002
DDA7
DDA6
DDA5
DDA4
DDA3
DDA2
DDA1
DDA0
DDRA(1)
$0003
DDB7
DDB6
DDB5
DDB4
DDB3
DDB2
DDB1
DDB0
DDRB(1)
$0004$0007
0
0
0
0
0
0
0
0
Reserved(3)
$0008
PE7
PE6
PE5
PE4
PE3
PE2
PE1
PE0
PORTE(2)
$0009
DDE7
DDE6
DDE5
DDE4
DDE3
DDE2
0
0
DDRE(2)
$000A
NDBE
CGMTE
PIPOE
NECLK
LSTRE
RDWE
CALE
DBENE
PEAR(3)
$000B
SMODN
MODB
MODA
ESTR
IVIS
EBSWAI
EMK
EME
MODE(3)
$000C
PUPK
PUPJ
PUPH
PUPE
0
0
PUPB
PUPA
PUCR(3)
$000D
RDPK
RDPJ
RDPH
RDPE
0
0
RDPB
RDPA
RDRIV(3)
$000E
0
0
0
0
0
0
0
0
Reserved(3)
$000F
0
0
0
0
0
0
0
0
Reserved(3)
$0010
RAM15
RAM14
RAM13
0
0
0
0
0
INITRM
$0011
REG15
REG14
REG13
REG12
REG11
0
0
MMSWAI
INITRG
$0012
EE15
EE14
EE13
EE12
0
0
0
EEON
INITEE
$0013
ROMTST
NDRF
RFSTR1
RFSTR0
EXSTR1
EXSTR0
ROMHM
ROMON
MISC
$0014
RTIE
RSWAI
RSBCK
Reserved
RTBYP
RTR2
RTR1
RTR0
RTICTL
$0015
RTIF
0
0
0
0
0
0
0
RTIFLG
$0016
CME
FCME
FCMCOP
WCOP
DISR
CR2
CR1
CR0
COPCTL
$0017
Bit 7
6
5
4
3
2
1
Bit 0
COPRST
$0018
ITE6
ITE8
ITEA
ITEC
ITEE
ITF0
ITF2
ITF4
ITST0
$0019
ITD6
ITD8
ITDA
ITDC
ITDE
ITE0
ITE2
ITE4
ITST1
$001A
ITC6
ITC8
ITCA
ITCC
ITCE
ITD0
ITD2
ITD4
ITST2
$001B
ITB6
ITB8
ITBA
ITBC
ITBE
ITC0
ITC2
ITC4
ITST3
$001C
0
0
0
0
0
0
0
0
Reserved
$001D
0
0
0
0
0
0
0
0
Reserved
$001E
IRQE
IRQEN
DLY
0
0
0
0
0
INTCR
$001F
1
PSEL6
PSEL5
PSEL4
PSEL3
PSEL2
PSEL1
0
HPRIO
$0020
BKEN1
BKEN0
BKPM
0
BK1ALE
BK0ALE
0
0
BRKCT0
$0021
0
BKDBE
BKMBH
BKMBL
BK1RWE
BK1RW
BK0RWE
BK0RW
BRKCT1
$0022
Bit 15
14
13
12
11
10
9
Bit 8
BRKAH
$0023
Bit 7
6
5
4
3
2
1
Bit 0
BRKAL
$0024
Bit 15
14
13
12
11
10
9
Bit 8
BRKDH
Table 4-1. Register Map (Sheet 1 of 10)
Technical Data
64
MC68HC912DG128 — Rev 3.0
Registers
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Registers
Register Block
Address
Bit 7
6
5
4
3
2
1
Bit 0
Name
$0025
Bit 7
6
5
4
3
2
1
Bit 0
BRKDL
$0026
0
0
0
0
0
0
0
0
Reserved
$0027
0
0
0
0
0
0
0
0
Reserved
$0028
PJ7
PJ6
PJ5
PJ4
PJ3
PJ2
PJ1
PJ0
PORTJ
$0029
PH7
PH6
PH5
PH4
PH3
PH2
PH1
PH0
PORTH
$002A
DDJ7
DDJ6
DDJ5
DDJ4
DDJ3
DDJ2
DDJ1
DDJ0
DDRJ
$002B
DDH7
DDH6
DDH5
DDH4
DDH3
DDH2
DDH1
DDH0
DDRH
$002C
KWIEJ7
KWIEJ6
KWIEJ5
KWIEJ4
KWIEJ3
KWIEJ2
KWIEJ1
KWIEJ0
KWIEJ
$002D
KWIEH7
KWIEH6
KWIEH5
KWIEH4
KWIEH3
KWIEH2
KWIEH1
KWIEH0
KWIEH
$002E
KWIFJ7
KWIFJ6
KWIFJ5
KWIFJ4
KWIFJ3
KWIFJ2
KWIFJ1
KWIFJ0
KWIFJ
$002F
KWIFH7
KWIFH6
KWIFH5
KWIFH4
KWIFH3
KWIFH2
KWIFH1
KWIFH0
KWIFH
$0030
KWPJ7
KWPJ6
KWPJ5
KWPJ4
KWPJ3
KWPJ2
KWPJ1
KWPJ0
KWPJ
$0031
KWPH7
KWPH6
KWPH5
KWPH4
KWPH3
KWPH2
KWPH1
KWPH0
KWPH
$0032
0
0
0
0
0
0
0
0
Reserved
$0033
0
0
0
0
0
0
0
0
Reserved
$0034–
$0037
Unimplemented(4)
Reserved
$0038
0
0
SYN5
SYN4
SYN3
SYN2
SYN1
SYN0
SYNR
$0039
0
0
0
0
0
REFDV2
REFDV1
REFDV0
REFDV
$003A
TSTOUT7 TSTOUT6 TSTOUT5 TSTOUT4 TSTOUT3 TSTOUT2 TSTOUT1 TSTOUT0
CGTFLG
$003B
LOCKIF
LOCK
0
0
0
0
LHIF
LHOME
PLLFLG
$003C
LOCKIE
PLLON
AUTO
ACQ
0
PSTP
LHIE
NOLHM
PLLCR
$003D
0
BCSP
BCSS
0
0
MCS
0
0
CLKSEL
$003E
0
0
SLDV5
SLDV4
SLDV3
SLDV2
SLDV1
SLDV0
SLOW
$003F
OPNLE
TRK
TSTCLKE
TST4
TST3
TST2
TST1
TST0
CGTCTL
$0040
CON23
CON01
PCKA2
PCKA1
PCKA0
PCKB2
PCKB1
PCKB0
PWCLK
$0041
PCLK3
PCLK2
PCLK1
PCLK0
PPOL3
PPOL2
PPOL1
PPOL0
PWPOL
$0042
0
0
0
0
PWEN3
PWEN2
PWEN1
PWEN0
PWEN
$0043
0
Bit 6
5
4
3
2
1
Bit 0
PWPRES
$0044
Bit 7
6
5
4
3
2
1
Bit 0
PWSCAL0
$0045
Bit 7
6
5
4
3
2
1
Bit 0
PWSCNT0
$0046
Bit 7
6
5
4
3
2
1
Bit 0
PWSCAL1
$0047
Bit 7
6
5
4
3
2
1
Bit 0
PWSCNT1
$0048
Bit 7
6
5
4
3
2
1
Bit 0
PWCNT0
$0049
Bit 7
6
5
4
3
2
1
Bit 0
PWCNT1
$004A
Bit 7
6
5
4
3
2
1
Bit 0
PWCNT2
$004B
Bit 7
6
5
4
3
2
1
Bit 0
PWCNT3
$004C
Bit 7
6
5
4
3
2
1
Bit 0
PWPER0
Table 4-1. Register Map (Sheet 2 of 10)
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Registers
For More Information On This Product,
Go to: www.freescale.com
65
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Registers
Address
Bit 7
6
5
4
3
2
1
Bit 0
Name
$004D
Bit 7
6
5
4
3
2
1
Bit 0
PWPER1
$004E
Bit 7
6
5
4
3
2
1
Bit 0
PWPER2
$004F
Bit 7
6
5
4
3
2
1
Bit 0
PWPER3
$0050
Bit 7
6
5
4
3
2
1
Bit 0
PWDTY0
$0051
Bit 7
6
5
4
3
2
1
Bit 0
PWDTY1
$0052
Bit 7
6
5
4
3
2
1
Bit 0
PWDTY2
$0053
Bit 7
6
5
4
3
2
1
Bit 0
PWDTY3
$0054
0
0
0
PSWAI
CENTR
RDPP
PUPP
PSBCK
PWCTL
$0055
DISCR
DISCP
DISCAL
0
0
0
0
0
PWTST
$0056
PP7
PP6
PP5
PP4
PP3
PP2
PP1
PP0
PORTP
$0057
DDP7
DDP6
DDP5
DDP4
DDP3
DDP2
DDP1
DDP0
DDRP
$0058$005F
0
0
0
0
0
0
0
0
Reserved
$0060
Reserved
ATD0CTL0
$0061
Reserved
ATD0CTL1
$0062
ADPU
AFFC
ASWAI
0
0
0
ASCIE
ASCIF
ATD0CTL2
$0063
0
0
0
0
0
0
FRZ1
FRZ0
ATD0CTL3
$0064
RES10
SMP1
SMP0
PRS4
PRS3
PRS2
PRS1
PRS0
ATD0CTL4
$0065
0
S8CM
SCAN
MULT
CD
CC
CB
CA
ATD0CTL5
$0066
SCF
0
0
0
0
CC2
CC1
CC0
ATD0STAT0
$0067
CCF7
CCF6
CCF5
CCF4
CCF3
CCF2
CCF1
CCF0
ATD0STAT1
$0068
SAR9
SAR8
SAR7
SAR6
SAR5
SAR4
SAR3
SAR2
ATD0TESTH
$0069
SAR1
SAR0
RST
TSTOUT
TST3
TST2
TST1
TST0
ATD0TESTL
$006A–$
006E
0
0
0
0
0
0
0
0
Reserved
$006F
PAD07
PAD06
PAD05
PAD04
PAD03
PAD02
PAD01
PAD00
PORTAD0
$0070
Bit 15
14
13
12
11
10
9
Bit 8
ADR00H
$0071
Bit 7
Bit 6
0
0
0
0
0
0
ADR00L
$0072
Bit 15
14
13
12
11
10
9
Bit 8
ADR01H
$0073
Bit 7
Bit 6
0
0
0
0
0
0
ADR01L
$0074
Bit 15
14
13
12
11
10
9
Bit 8
ADR02H
$0075
Bit 7
Bit 6
0
0
0
0
0
0
ADR02L
$0076
Bit 15
14
13
12
11
10
9
Bit 8
ADR03H
$0077
Bit 7
Bit 6
0
0
0
0
0
0
ADR03L
$0078
Bit 15
14
13
12
11
10
9
Bit 8
ADR04H
$0079
Bit 7
Bit 6
0
0
0
0
0
0
ADR04L
$007A
Bit 15
14
13
12
11
10
9
Bit 8
ADR05H
$007B
Bit 7
Bit 6
0
0
0
0
0
0
ADR05L
$007C
Bit 15
14
13
12
11
10
9
Bit 8
ADR06H
Table 4-1. Register Map (Sheet 3 of 10)
Technical Data
66
MC68HC912DG128 — Rev 3.0
Registers
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Registers
Register Block
Address
Bit 7
6
5
4
3
2
1
Bit 0
Name
$007D
Bit 7
Bit 6
0
0
0
0
0
0
ADR06L
$007E
Bit 15
14
13
12
11
10
9
Bit 8
ADR07H
$007F
Bit 7
Bit 6
0
0
0
0
0
0
ADR07L
$0080
IOS7
IOS6
IOS5
IOS4
IOS3
IOS2
IOS1
IOS0
TIOS
$0081
FOC7
FOC6
FOC5
FOC4
FOC3
FOC2
FOC1
FOC0
CFORC
$0082
OC7M7
OC7M6
OC7M5
OC7M4
OC7M3
OC7M2
OC7M1
OC7M0
OC7M
$0083
OC7D7
OC7D6
OC7D5
OC7D4
OC7D3
OC7D2
OC7D1
OC7D0
OC7D
$0084
Bit 15
14
13
12
11
10
9
Bit 8
TCNT
$0085
Bit 7
6
5
4
3
2
1
Bit 0
TCNT
$0086
TEN
TSWAI
TSBCK
TFFCA
$0087
Reserved
TSCR
Reserved
TQCR
$0088
OM7
OL7
OM6
OL6
OM5
OL5
OM4
OL4
TCTL1
$0089
OM3
OL3
OM2
OL2
OM1
OL1
OM0
OL0
TCTL2
$008A
EDG7B
EDG7A
EDG6B
EDG6A
EDG5B
EDG5A
EDG4B
EDG4A
TCTL3
$008B
EDG3B
EDG3A
EDG2B
EDG2A
EDG1B
EDG1A
EDG0B
EDG0A
TCTL4
$008C
C7I
C6I
C5I
C4I
C3I
C2I
C1I
C0I
TMSK1
$008D
TOI
0
PUPT
RDPT
TCRE
PR2
PR1
PR0
TMSK2
$008E
C7F
C6F
C5F
C4F
C3F
C2F
C1F
C0F
TFLG1
$008F
TOF
0
0
0
0
0
0
0
TFLG2
$0090
Bit 15
14
13
12
11
10
9
Bit 8
TC0
$0091
Bit 7
6
5
4
3
2
1
Bit 0
TC0
$0092
Bit 15
14
13
12
11
10
9
Bit 8
TC1
$0093
Bit 7
6
5
4
3
2
1
Bit 0
TC1
$0094
Bit 15
14
13
12
11
10
9
Bit 8
TC2
$0095
Bit 7
6
5
4
3
2
1
Bit 0
TC2
$0096
Bit 15
14
13
12
11
10
9
Bit 8
TC3
$0097
Bit 7
6
5
4
3
2
1
Bit 0
TC3
$0098
Bit 15
14
13
12
11
10
9
Bit 8
TC4
$0099
Bit 7
6
5
4
3
2
1
Bit 0
TC4
$009A
Bit 15
14
13
12
11
10
9
Bit 8
TC5
$009B
Bit 7
6
5
4
3
2
1
Bit 0
TC5
$009C
Bit 15
14
13
12
11
10
9
Bit 8
TC6
$009D
Bit 7
6
5
4
3
2
1
Bit 0
TC6
$009E
Bit 15
14
13
12
11
10
9
Bit 8
TC7
$009F
Bit 7
6
5
4
3
2
1
Bit 0
TC7
$00A0
0
PAEN
PAMOD
PEDGE
CLK1
CLK0
PAOVI
PAI
PACTL
$00A1
0
0
0
0
0
0
PAOVF
PAIF
PAFLG
$00A2
Bit 7
6
5
4
3
2
1
Bit 0
PACN3
Table 4-1. Register Map (Sheet 4 of 10)
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Registers
For More Information On This Product,
Go to: www.freescale.com
67
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Registers
Address
Bit 7
6
5
4
3
2
1
Bit 0
Name
$00A3
Bit 7
6
5
4
3
2
1
Bit 0
PACN2
$00A4
Bit 7
6
5
4
3
2
1
Bit 0
PACN1
$00A5
Bit 7
6
5
4
3
2
1
Bit 0
PACN0
$00A6
MCZI
MODMC
RDMCL
ICLAT
FLMC
MCEN
MCPR1
MCPR0
MCCTL
$00A7
MCZF
0
0
0
POLF3
POLF2
POLF1
POLF0
MCFLG
$00A8
0
0
0
0
PA3EN
PA2EN
PA1EN
PA0EN
ICPAR
$00A9
0
0
0
0
0
0
DLY1
DLY0
DLYCT
$00AA
NOVW7
NOVW6
NOVW5
NOVW4
NOVW3
NOVW2
NOVW1
NOVW0
ICOVW
$00AB
SH37
SH26
SH15
SH04
TFMOD
PACMX
BUFEN
LATQ
ICSYS
$00AC
0
0
0
0
0
0
0
0
Reserved
$00AD
0
0
0
0
0
0
TCBYP
0
TIMTST
$00AE
PT7
PT6
PT5
PT4
PT3
PT2
PT1
PT0
PORTT
$00AF
DDT7
DDT6
DDT5
DDT4
DDT3
DDT2
DDT1
DDT0
DDRT
$00B0
0
PBEN
0
0
0
0
PBOVI
0
PBCTL
$00B1
0
0
0
0
0
0
PBOVF
0
PBFLG
$00B2
Bit 7
6
5
4
3
2
1
Bit 0
PA3H
$00B3
Bit 7
6
5
4
3
2
1
Bit 0
PA2H
$00B4
Bit 7
6
5
4
3
2
1
Bit 0
PA1H
$00B5
Bit 7
6
5
4
3
2
1
Bit 0
PA0H
$00B6
Bit 15
14
13
12
11
10
9
Bit 8
MCCNTH
$00B7
Bit 7
6
5
4
3
2
1
Bit 0
MCCNTL
$00B8
Bit 15
14
13
12
11
10
9
Bit 8
TC0H
$00B9
Bit 7
6
5
4
3
2
1
Bit 0
TC0H
$00BA
Bit 15
14
13
12
11
10
9
Bit 8
TC1H
$00BB
Bit 7
6
5
4
3
2
1
Bit 0
TC1H
$00BC
Bit 15
14
13
12
11
10
9
Bit 8
TC2H
$00BD
Bit 7
6
5
4
3
2
1
Bit 0
TC2H
$00BE
Bit 15
14
13
12
11
10
9
Bit 8
TC3H
$00BF
Bit 7
6
5
4
3
2
1
Bit 0
TC3H
$00C0
BTST
BSPL
BRLD
SBR12
SBR11
SBR10
SBR9
SBR8
SC0BDH
$00C1
SBR7
SBR6
SBR5
SBR4
SBR3
SBR2
SBR1
SBR0
SC0BDL
$00C2
LOOPS
WOMS
RSRC
M
WAKE
ILT
PE
PT
SC0CR1
$00C3
TIE
TCIE
RIE
ILIE
TE
RE
RWU
SBK
SC0CR2
$00C4
TDRE
TC
RDRF
IDLE
OR
NF
FE
PF
SC0SR1
$00C5
0
0
0
0
0
0
0
RAF
SC0SR2
$00C6
R8
T8
0
0
0
0
0
0
SC0DRH
$00C7
R7/T7
R6/T6
R5/T5
R4/T4
R3/T3
R2/T2
R1/T1
R0/T0
SC0DRL
$00C8
BTST
BSPL
BRLD
SBR12
SBR11
SBR10
SBR9
SBR8
SC1BDH
Table 4-1. Register Map (Sheet 5 of 10)
Technical Data
68
MC68HC912DG128 — Rev 3.0
Registers
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Registers
Register Block
Address
Bit 7
6
5
4
3
2
1
Bit 0
Name
$00C9
SBR7
SBR6
SBR5
SBR4
SBR3
SBR2
SBR1
SBR0
SC1BDL
$00CA
LOOPS
WOMS
RSRC
M
WAKE
ILT
PE
PT
SC1CR1
$00CB
TIE
TCIE
RIE
ILIE
TE
RE
RWU
SBK
SC1CR2
$00CC
TDRE
TC
RDRF
IDLE
OR
NF
FE
PF
SC1SR1
$00CD
0
0
0
0
0
0
0
RAF
SC1SR2
$00CE
R8
T8
0
0
0
0
0
0
SC1DRH
$00CF
R7/T7
R6/T6
R5/T5
R4/T4
R3/T3
R2/T2
R1/T1
R0/T0
SC1DRL
$00D0
SPIE
SPE
SWOM
MSTR
CPOL
CPHA
SSOE
LSBF
SP0CR1
$00D1
0
0
0
0
PUPS
RDPS
SSWAI
SPC0
SP0CR2
$00D2
0
0
0
0
0
SPR2
SPR1
SPR0
SP0BR
$00D3
SPIF
WCOL
0
MODF
0
0
0
0
SP0SR
$00D4
0
0
0
0
0
0
0
0
Reserved
$00D5
Bit 7
6
5
4
3
2
1
Bit 0
SP0DR
$00D6
PS7
PS6
PS5
PS4
PS3
PS2
PS1
PS0
PORTS
$00D7
DDS7
DDS6
DDS5
DDS4
DDS3
DDS2
DDS1
DDS0
DDRS
$00D8–$
00DF
0
0
0
0
0
0
0
0
Reserved
$00E0
ADR7
ADR6
ADR5
ADR4
ADR3
ADR2
ADR1
0
IBAD
$00E1
0
0
IBC5
IBC4
IBC3
IBC2
IBC1
IBC0
IBFD
$00E2
IBEN
IBIE
MS/SL
Tx/Rx
TXAK
RSTA
0
IBSWAI
IBCR
$00E3
TCF
IAAS
IBB
IBAL
0
SRW
IBIF
RXAK
IBSR
$00E4
D7
D6
D5
D4
D3
D2
D1
D0
IBDR
$00E5
0
0
0
RDPIB
0
0
0
PUPIB
IBPURD
$00E6
PIB7
PIB6
PIB5
PIB4
PIB3
PIB2
PIB1
PIB0
PORTIB
$00E7
DDRIB7
DDRIB6
DDRIB5
DDRIB4
DDRIB3
DDRIB2
DDRIB1
DDRIB0
DDRIB
$00E8–
$00EF
Unimplemented(4)
1
Reserved
$00F0
NOBDML
NOSHB
$00F1
SHPROT
1
$00F2
EEODD
EEVEN
MARG
EECPD
EECPRD
0
EECPM
0
EETST
$00F3
BULKP
0
0
BYTE
ROW
ERASE
EELAT
EEPGM
EEPROG
$00F4
0
0
0
0
0
0
0
LOCK
FEELCK
$00F5
0
0
0
0
0
0
0
BOOTP
FEEMCR
$00F6
FSTE
GADR
HVT
FENLV
FDISVFP
VTCK
STRE
MWPR
FEETST
$00F7
0
0
0
FESWAI
SVFP
ERAS
LAT
ENPE
FEECTL
$00F8
MT07
MT06
MT05
MT04
MT03
MT02
MT01
MT00
MTST0
$00F9
MT0F
MT0E
MT0D
MT0C
MT0B
MT0A
MT09
MT08
MTST1
Reserved
EESWAI PROTLCK
EERC
EEMCR
BPROT5 BPROT4 BPROT3 BPROT2 BPROT1 BPROT0
EEPROT
$00FA
MT17
MT16
MT15
MT14
MT13
MT12
MT11
MT10
MTST2
$00FB
MT1F
MT1E
MT1D
MT1C
MT1B
MT1A
MT19
MT18
MTST3
Table 4-1. Register Map (Sheet 6 of 10)
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Registers
For More Information On This Product,
Go to: www.freescale.com
69
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Registers
Address
Bit 7
6
5
4
3
2
1
Bit 0
Name
$00FC
PK7
0
0
0
PK3
PK2
PK1
PK0
PORTK(5)
$00FD
DDK7
0
0
0
DDK3
DDK2
DDK1
DDK0
DDRK(5)
$00FE
0
0
0
0
0
0
0
0
Reserved
$00FF
0
0
0
0
0
PIX2
PIX1
PIX0
PPAGE
$0100
0
0
CSWAI
SYNCH
TLNKEN
SLPAK
SLPRQ
SFTRES
C0MCR0
$0101
0
0
0
0
0
LOOPB
WUPM
CLKSRC
C0MCR1
$0102
SJW1
SJW0
BRP5
BRP4
BRP3
BRP2
BRP1
BRP0
C0BTR0
$0103
SAMP
TSEG22
TSEG21
TSEG20
TSEG13
TSEG12
TSEG11
TSEG10
C0BTR1
$0104
WUPIF
RWRNIF
TWRNIF
RERRIF
TERRIF
BOFFIF
OVRIF
RXF
C0RFLG
$0105
WUPIE
RWRNIE
TWRNIE
RERRIE
TERRIE
BOFFIE
OVRIE
RXFIE
C0RIER
$0106
0
ABTAK2
ABTAK1
ABTAK0
0
TXE2
TXE1
TXE0
C0TFLG
$0107
0
ABTRQ2 ABTRQ1 ABTRQ0
0
TXEIE2
TXEIE1
TXEIE0
C0TCR
$0108
0
0
IDHIT2
IDHIT1
IDHIT0
C0IDAC
0
IDAM1
IDAM0
$0109–
$010D
Unimplemented(4)
Reserved
$010E
RXERR7 RXERR6 RXERR5 RXERR4 RXERR3 RXERR2 RXERR1 RXERR0
C0RXERR
$010F
TXERR7
TXERR6
TXERR5
TXERR4
TXERR3
TXERR2
TXERR1
TXERR0
C0TXERR
$0110
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
C0IDAR0
$0111
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
C0IDAR1
$0112
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
C0IDAR2
$0113
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
C0IDAR3
$0114
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
C0IDMR0
$0115
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
C0IDMR1
$0116
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
C0IDMR2
$0117
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
C0IDMR3
$0118
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
C0IDAR4
$0119
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
C0IDAR5
$011A
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
C0IDAR6
$011B
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
C0IDAR7
$011C
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
C0IDMR4
$011D
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
C0IDMR5
$011E
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
C0IDMR6
$011F
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
C0IDMR7
$0120–
$013C
Unimplemented(4)
Reserved
$013D
0
0
0
0
0
0
$013E
PCAN7
PCAN6
PCAN5
PCAN4
PCAN3
PCAN2
$013F
PUPCAN RDPCAN PCTLCAN0
TxCAN
RxCAN
PORTCAN0
0
0
DDRCAN0
DDCAN7 DDCAN6 DDCAN5 DDCAN4 DDCAN3 DDCAN2
Table 4-1. Register Map (Sheet 7 of 10)
Technical Data
70
MC68HC912DG128 — Rev 3.0
Registers
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Registers
Register Block
Address
Bit 7
6
5
4
3
2
1
Bit 0
Name
$0140–
$014F
FOREGROUND RECEIVE BUFFER 0
RxFG0
$0150–
$015F
TRANSMIT BUFFER 00
Tx00
$0160–
$016F
TRANSMIT BUFFER 01
Tx01
$0170–
$017F
TRANSMIT BUFFER 02
Tx02
$0180–
$01DF
Unimplemented(4)
Reserved
$01E0
Reserved
ATD1CTL0
$01E1
Reserved
ATD1CTL1
$01E2
ADPU
AFFC
ASWAI
0
0
0
ASCIE
ASCIF
ATD1CTL2
$01E3
0
0
0
0
0
0
FRZ1
FRZ0
ATD1CTL3
$01E4
RES10
SMP1
SMP0
PRS4
PRS3
PRS2
PRS1
PRS0
ATD1CTL4
$01E5
0
S8CM
SCAN
MULT
CD
CC
CB
CA
ATD1CTL5
$01E6
SCF
0
0
0
0
CC2
CC1
CC0
ATD1STAT0
$01E7
CCF7
CCF6
CCF5
CCF4
CCF3
CCF2
CCF1
CCF0
ATD1STAT1
$01E8
SAR9
SAR8
SAR7
SAR6
SAR5
SAR4
SAR3
SAR2
ATD1TESTH
$01E9
SAR1
SAR0
RST
TSTOUT
TST3
TST2
TST1
TST0
ATD1TESTL
$01EA–$
01EE
0
0
0
0
0
0
0
0
Reserved
$01EF
PAD17
PAD16
PAD15
PAD14
PAD13
PAD12
PAD11
PAD10
PORTAD1
$01F0
Bit 15
14
13
12
11
10
9
Bit 8
ADR10H
$01F1
Bit 7
Bit 6
0
0
0
0
0
0
ADR10L
$01F2
Bit 15
14
13
12
11
10
9
Bit 8
ADR11H
$01F3
Bit 7
Bit 6
0
0
0
0
0
0
ADR11L
$01F4
Bit 15
14
13
12
11
10
9
Bit 8
ADR12H
$01F5
Bit 7
Bit 6
0
0
0
0
0
0
ADR12L
$01F6
Bit 15
14
13
12
11
10
9
Bit 8
ADR13H
$01F7
Bit 7
Bit 6
0
0
0
0
0
0
ADR13L
$01F8
Bit 15
14
13
12
11
10
9
Bit 8
ADR14H
$01F9
Bit 7
Bit 6
0
0
0
0
0
0
ADR14L
$01FA
Bit 15
14
13
12
11
10
9
Bit 8
ADR15H
$01FB
Bit 7
Bit 6
0
0
0
0
0
0
ADR15L
$01FC
Bit 15
14
13
12
11
10
9
Bit 8
ADR16H
$01FD
Bit 7
Bit 6
0
0
0
0
0
0
ADR16L
$01FE
Bit 15
14
13
12
11
10
9
Bit 8
ADR17H
$01FF
Bit 7
Bit 6
0
0
0
0
0
0
ADR17L
Table 4-1. Register Map (Sheet 8 of 10)
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Registers
For More Information On This Product,
Go to: www.freescale.com
71
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Registers
Address
Bit 7
6
5
$0200$02FF
4
3
2
1
Bit 0
Unimplemented(4)
Name
Reserved
$0300
0
0
CSWAI
SYNCH
TLNKEN
SLPAK
SLPRQ
SFTRES
C1MCR0
$0301
0
0
0
0
0
LOOPB
WUPM
CLKSRC
C1MCR1
$0302
SJW1
SJW0
BRP5
BRP4
BRP3
BRP2
BRP1
BRP0
C1BTR0
$0303
SAMP
TSEG22
TSEG21
TSEG20
TSEG13
TSEG12
TSEG11
TSEG10
C1BTR1
$0304
WUPIF
RWRNIF
TWRNIF
RERRIF
TERRIF
BOFFIF
OVRIF
RXF
C1RFLG
$0305
WUPIE
RWRNIE
TWRNIE
RERRIE
TERRIE
BOFFIE
OVRIE
RXFIE
C1RIER
$0306
0
ABTAK2
ABTAK1
ABTAK0
0
TXE2
TXE1
TXE0
C1TFLG
$0307
0
ABTRQ2 ABTRQ1 ABTRQ0
0
TXEIE2
TXEIE1
TXEIE0
C1TCR
$0308
0
0
IDHIT2
IDHIT1
IDHIT0
C1IDAC
0
IDAM1
IDAM0
$0309–
$030D
Unimplemented(4)
$030E
RXERR7 RXERR6 RXERR5 RXERR4 RXERR3 RXERR2 RXERR1 RXERR0
C1RXERR
$030F
TXERR7
TXERR6
TXERR5
TXERR4
TXERR3
TXERR2
TXERR1
TXERR0
C1TXERR
$0310
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
C1IDAR0
$0311
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
C1IDAR1
$0312
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
C1IDAR2
$0313
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
C1IDAR3
$0314
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
C1IDMR0
$0315
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
C1IDMR1
$0316
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
C1IDMR2
$0317
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
C1IDMR3
$0318
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
C1IDAR4
$0319
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
C1IDAR5
$031A
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
C1IDAR6
Reserved
Table 4-1. Register Map (Sheet 9 of 10)
Technical Data
72
MC68HC912DG128 — Rev 3.0
Registers
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Registers
Address
Bit 7
6
5
4
3
2
1
Bit 0
Name
$031B
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
C1IDAR7
$031C
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
C1IDMR4
$031D
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
C1IDMR5
$031E
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
C1IDMR6
$031F
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
C1IDMR7
$0320–
$033C
Unimplemented(4)
$033D
$033E
$033F
Reserved
0
0
0
0
0
0
PCAN7
PCAN6
PCAN5
PCAN4
PCAN3
PCAN2
PUPCAN RDPCAN PCTLCAN1
TxCAN
RxCAN
PORTCAN1
0
0
DDRCAN1
DDCAN7 DDCAN6 DDCAN5 DDCAN4 DDCAN3 DDCAN2
$0340–
$034F
FOREGROUND RECEIVE BUFFER 1
RxFG1
$0350–
$035F
TRANSMIT BUFFER 10
Tx10
$0360–
$036F
TRANSMIT BUFFER 11
Tx11
$0370–
$037F
TRANSMIT BUFFER 12
Tx12
$0380$03FF
Unimplemented(4)
Reserved
= Reserved or unimplemented bits.
Table 4-1. Register Map (Sheet 10 of 10)
1. Port A, port B and data direction registers DDRA, DDRB are not in map in expanded and peripheral modes.
2. Port E and DDRE not in the map in peripheral and expanded modes with EME set.
3. Registers also not in map in peripheral mode.
4. Data read at these locations is undefined.
5. Port K and DDRK not in the map in peripheral and expanded modes with EMK set.
Technical Data
73
MC68HC912DG128 — Rev 3.0
Registers
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Registers
Technical Data
74
MC68HC912DG128 — Rev 3.0
Registers
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Section 5. Operating Modes
5.1 Contents
5.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
5.3
Operating Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75
5.4
Background Debug Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 78
5.5
Internal Resource Mapping. . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
5.6
Memory Maps . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 93
5.2 Introduction
Eight possible operating modes determine the operating configuration of
the MC68HC912DG128. Each mode has an associated default memory
map and external bus configuration. After reset, most system resources
can be mapped to other addresses by writing to the appropriate control
registers.
5.3 Operating Modes
The operating mode out of reset is determined by the states of the
BKGD, MODB, and MODA pins during reset.
The SMODN, MODB, and MODA bits in the MODE register show current
operating mode and provide limited mode switching during operation.
The states of the BKGD, MODB, and MODA pins are latched into these
bits on the rising edge of the reset signal.
In expanded modes, all address space not used by internal resources is
by default external memory.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Operating Modes
For More Information On This Product,
Go to: www.freescale.com
75
Freescale Semiconductor, Inc.
Operating Modes
Freescale Semiconductor, Inc...
Table 5-1. Mode Selection
BKGD
MODB
MODA
Mode
Port A
Port B
1
0
0
Normal Single Chip
G.P. I/O
G.P. I/O
1
0
1
Normal Expanded Narrow
ADDR/DATA
ADDR
1
1
0
Reserved (Forced to
Peripheral)
—
—
1
1
1
Normal Expanded Wide
ADDR/DATA
ADDR/DATA
0
0
0
Special Single Chip
G.P. I/O
G.P. I/O
0
0
1
Special Expanded Narrow
ADDR/DATA
ADDR
0
1
0
Special Peripheral
ADDR/DATA
ADDR/DATA
0
1
1
Special Expanded Wide
ADDR/DATA
ADDR/DATA
There are two basic types of operating modes:
Normal modes — some registers and bits are protected
against accidental changes.
Special modes — allow greater access to protected control
registers and bits for special purposes such as testing and
emulation.
For operation above 105°C, the MC68HC912DG128 (M temperature
range product only) is limited to single chip modes of operation.
A system development and debug feature, background debug mode
(BDM), is available in all modes. In special single-chip mode, BDM is
active immediately after reset.
5.3.1 Normal Operating Modes
These modes provide three operating configurations. Background
debugging is available in all three modes, but must first be enabled for
some operations by means of a BDM background command, then
activated.
Technical Data
76
MC68HC912DG128 — Rev 3.0
Operating Modes
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Operating Modes
Operating Modes
Normal Single-Chip Mode — There are no external address
and data buses in this mode. The MCU operates as a standalone device and all program and data resources are on-chip.
External port pins normally associated with address and data
buses can be used for general-purpose I/O.
Normal Expanded Wide Mode — This is a normal mode of
operation in which the expanded bus is present with a 16-bit
data bus. Ports A and B are used for the 16-bit multiplexed
address/data bus.
Normal Expanded Narrow Mode — This is a normal mode of
operation in which the expanded bus is present with an 8-bit
data bus. Ports A and B are used for the16-bit address bus.
Port A is used as the data bus, multiplexed with addresses. In
this mode, 16-bit data is presented one byte at a time, the high
byte followed by the low byte. The address is automatically
incremented on the second cycle.
5.3.2 Special Operating Modes
There are three special operating modes that correspond to normal
operating modes. These operating modes are commonly used in factory
testing and system development. In addition, there is a special
peripheral mode, in which an external master, such as an I.C. tester, can
control the on-chip peripherals.
Special Single-Chip Mode — This mode can be used to force
the MCU to active BDM mode to allow system debug through
the BKGD pin. There are no external address and data buses
in this mode. The MCU operates as a stand-alone device and
all program and data space are on-chip. External port pins can
be used for general-purpose I/O.
Special Expanded Wide Mode — This mode can be used for
emulation of normal expanded wide mode and emulation of
normal single-chip mode. Ports A and B are used for the 16-bit
multiplexed address/data bus.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Operating Modes
For More Information On This Product,
Go to: www.freescale.com
77
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Operating Modes
Special Expanded Narrow Mode — This mode can be used
for emulation of normal expanded narrow mode. Ports A and B
are used for the16-bit address bus. Port A is used as the data
bus, multiplexed with addresses. In this mode, 16-bit data is
presented one byte at a time, the high byte followed by the low
byte. The address is automatically incremented on the second
cycle.
Special Peripheral Mode — The CPU is not active in this
mode. An external master can control on-chip peripherals for
testing purposes. It is not possible to change to or from this
mode without going through reset. Background debugging
should not be used while the MCU is in special peripheral
mode as internal bus conflicts between BDM and the external
master can cause improper operation of both modes.
Bit 7
6
5
4
3
2
1
Bit 0
SMODN
MODB
MODA
ESTR
IVIS
EBSWAI
EMK
EME
RESET:
0
0
0
1
1
0
1
1
Special Single Chip
RESET:
0
0
1
1
1
0
1
1
Special Exp Nar
RESET:
0
1
0
1
1
0
1
1
Peripheral
RESET:
0
1
1
1
1
0
1
1
Special Exp Wide
RESET:
1
0
0
1
0
0
0
0
Normal Single Chip
RESET:
1
0
1
1
0
0
0
0
Normal Exp Nar
RESET:
1
1
1
1
0
0
0
0
Normal Exp Wide
MODE — Mode Register
$000B
5.4 Background Debug Mode
Background debug mode (BDM) is an auxiliary operating mode that is
used for system development. BDM is implemented in on-chip hardware
and provides a full set of debug operations. Some BDM commands can
be executed while the CPU is operating normally. Other BDM
commands are firmware based, and require the BDM firmware to be
enabled and active for execution.
Technical Data
78
MC68HC912DG128 — Rev 3.0
Operating Modes
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Operating Modes
Background Debug Mode
In special single-chip mode, BDM is enabled and active immediately out
of reset. BDM is available in all other operating modes, but must be
enabled before it can be activated. BDM should not be used in special
peripheral mode because of potential bus conflicts.
Once enabled, background mode can be made active by a serial
command sent via the BKGD pin or execution of a CPU12 BGND
instruction. While background mode is active, the CPU can interpret
special debugging commands, and read and write CPU registers,
peripheral registers, and locations in memory.
While BDM is active, the CPU executes code located in a small on-chip
ROM mapped to addresses $FF20 to $FFFF, and BDM control registers
are accessible at addresses $FF00 to $FF06. The BDM ROM replaces
the regular system vectors while BDM is active. While BDM is active, the
user memory from $FF00 to $FFFF is not in the map except through
serial BDM commands.
Bit 7
6
5
4
3
2
1
Bit 0
SMODN
MODB
MODA
ESTR
IVIS
EBSWAI
0
EME
RESET:
0
0
0
1
1
0
0
1
Special Single Chip
RESET:
0
0
1
1
1
0
0
1
Special Exp Nar
RESET:
0
1
0
1
1
0
0
1
Peripheral
RESET:
0
1
1
1
1
0
0
1
Special Exp Wide
RESET:
1
0
0
1
0
0
0
0
Normal Single Chip
RESET:
1
0
1
1
0
0
0
0
Normal Exp Nar
RESET:
1
1
1
1
0
0
0
0
Normal Exp Wide
MODE — Mode Register
$000B
The MODE register controls the MCU operating mode and various
configuration options. This register is not in the map in peripheral mode
SMODN, MODB, MODA — Mode Select Special, B and A
These bits show the current operating mode and reflect the status of
the BKGD, MODB and MODA input pins at the rising edge of reset.
SMODN is Read anytime. May only be written in special modes
(SMODN = 0). The first write is ignored;
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Operating Modes
For More Information On This Product,
Go to: www.freescale.com
79
Freescale Semiconductor, Inc.
Operating Modes
MODB, MODA may be written once in Normal modes (SMODN = 1).
Write anytime in special modes (first write is ignored) – special
peripheral and reserved modes cannot be selected.
ESTR — E Clock Stretch Enable
Freescale Semiconductor, Inc...
Determines if the E Clock behaves as a simple free-running clock or
as a bus control signal that is active only for external bus cycles.
ESTR is always one in expanded modes since it is required for
address and data bus de-multiplexing and must follow stretched
cycles.
0 = E never stretches (always free running).
1 = E stretches high during external access cycles and low during
non-visible internal accesses (IVIS = 0).
Normal modes: write once; Special modes: write anytime. Read
anytime.
IVIS — Internal Visibility
This bit determines whether internal ADDR, DATA, R/W and LSTRB
signals can be seen on the external bus during accesses to internal
locations. In Special Narrow Mode if this bit is set and an internal
access occurs the data will appear wide on Ports A and B. This serves
the same function as the EMD bit of the non-multiplexed versions of
the HC12 and allows for emulation. Visibility is not available when the
part is operating in a single-chip mode.
0 = No visibility of internal bus operations on external bus.
1 = Internal bus operations are visible on external bus.
Normal modes: write once; Special modes: write anytime EXCEPT
the first time. Read anytime.
Technical Data
80
MC68HC912DG128 — Rev 3.0
Operating Modes
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Operating Modes
Internal Resource Mapping
EBSWAI — External Bus Module Stop in Wait Control
This bit controls access to the external bus interface when in wait
mode. The module will delay before shutting down in wait mode to
allow for final bus activity to complete.
0 = External bus and registers continue functioning during wait
mode.
1 = External bus is shut down during wait mode.
Normal modes: write anytime; special modes: write never. Read
anytime.
EMK — Emulate Port K
In single-chip mode PORTK and DDRK are always in the map
regardless of the state of this bit.
0 = Port K and DDRK registers are in the memory map. Memory
expansion emulation is disabled and all pins are general
purpose I/O.
1 = In expanded or peripheral mode, PORTK and DDRK are
removed from the internal memory map. Removing these
registers from the map allows the user to emulate the function
of these registers externally.
Normal modes: write once; special modes: write anytime EXCEPT
the first time. Read anytime.
5.5 Internal Resource Mapping
The internal register block, RAM, and EEPROM have default locations
within the 64K byte standard address space but may be reassigned to
other locations during program execution by setting bits in mapping
registers INITRG, INITRM, and INITEE. During normal operating modes
these registers can be written once. It is advisable to explicitly establish
these resource locations during the initialization phase of program
execution, even if default values are chosen, in order to protect the
registers from inadvertent modification later.
Writes to the mapping registers go into effect between the cycle that
follows the write and the cycle after that. To assure that there are no
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Operating Modes
For More Information On This Product,
Go to: www.freescale.com
81
Freescale Semiconductor, Inc.
Operating Modes
unintended operations, a write to one of these registers should be
followed with a NOP instruction.
If conflicts occur when mapping resources, the register block will take
precedence over the other resources; RAM or EEPROM addresses
occupied by the register block will not be available for storage. When
active, BDM ROM takes precedence over other resources, although a
conflict between BDM ROM and register space is not possible. The
following table shows resource mapping precedence.
Freescale Semiconductor, Inc...
The MC68HC912DG128 contains 128K bytes of Flash EEPROM
nonvolatile memory which can be used to store program code or static
data. This physical memory comprises four 32k byte array modules,
00FEE32K, 01FEE32K, 10FEE32K and 11FEE32K. The 32K byte array
11FEE32K has a fixed location from $4000 to $7FFF and $C000 to
$FFFF. The three 32K byte arrays 00FEE32K, 01FEE32K and
10FEE32K are accessible through a 16K byte program page window
mapped from $8000 to $BFFF. The fixed 32K byte array 11FEE32K can
also be accessed through the program page window..
Table 5-2. Mapping Precedence
Precedence
Resource
1
BDM ROM (if active)
2
Register Space
3
RAM
4
EEPROM
5
On-Chip Flash EEPROM
6
External Memory
5.5.1 Register Block Mapping
After reset the 1K byte register block resides at location $0000 but can
be reassigned to any 2K byte boundary within the standard 64K byte
address space. Mapping of internal registers is controlled by five bits in
the INITRG register. The register block occupies the first 1K byte bytes
of the 2K byte block.
Technical Data
82
MC68HC912DG128 — Rev 3.0
Operating Modes
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Operating Modes
Internal Resource Mapping
INITRG — Initialization of Internal Register Position Register
RESET:
$0011
Bit 7
6
5
4
3
2
1
Bit 0
REG15
REG14
REG13
REG12
REG11
0
0
MMSWAI
0
0
0
0
0
0
0
0
REG[15:11] — Internal register map position
These bits specify the upper five bits of the 16-bit registers address.
Normal modes: write once; special modes: write anytime. Read
anytime.
MMSWAI — Memory Mapping Interface Stop in Wait Control
This bit controls access to the memory mapping interface when in
Wait mode.
Normal modes: write anytime; special modes: write never. Read
anytime.
0 = Memory mapping interface continues to function during Wait
mode.
1 = Memory mapping interface access is shut down during Wait
mode.
5.5.2 RAM Mapping
The MC68HC912DG128 has 8K bytes of fully static RAM that is used for
storing instructions, variables, and temporary data during program
execution. Since the RAM is actually implemented with two 4K RAM
arrays, any misaligned word access between last address of first 4K
RAM and first address of second 4K RAM will take two cycles instead of
one. After reset, RAM addressing begins at location $2000 but can be
assigned to any 8K byte boundary within the standard 64K byte address
space. Mapping of internal RAM is controlled by three bits in the INITRM
register.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Operating Modes
For More Information On This Product,
Go to: www.freescale.com
83
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Operating Modes
INITRM — Initialization of Internal RAM Position Register
$0010
Bit 7
6
5
4
3
2
1
Bit 0
RAM15
RAM14
RAM13
0
0
0
0
0
0
0
1
0
0
0
0
0
RESET:
RAM[15:13] — Internal RAM map position
These bits specify the upper three bits of the 16-bit RAM address.
Normal modes: write once; special modes: write anytime. Read
anytime.
5.5.3 EEPROM Mapping
The MC68HC912DG128 has 2K bytes of EEPROM which is activated by
the EEON bit in the INITEE register. Mapping of internal EEPROM is
controlled by four bits in the INITEE register. After reset EEPROM
address space begins at location $0800 but can be mapped to any 4K
byte boundary within the standard 64K byte address space. The
EEPROM block occupies the last 2K bytes of the 4K byte block.
INITEE— Initialization of Internal EEPROM Position Register
$0012
Bit 7
6
5
4
3
2
1
Bit 0
EE15
EE14
EE13
EE12
0
0
0
EEON
0
0
0
0
0
0
0
1
RESET:
EE[15:12] — Internal EEPROM map position
These bits specify the upper four bits of the 16-bit EEPROM address.
Normal modes: write once; special modes: write anytime. Read
anytime.
EEON — internal EEPROM On (Enabled)
This bit is forced to one in single-chip modes.
Read or write anytime.
0 = Removes the EEPROM from the map.
1 = Places the on-chip EEPROM in the memory map at the address
selected by EE[15:12].
Technical Data
84
MC68HC912DG128 — Rev 3.0
Operating Modes
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Operating Modes
Internal Resource Mapping
5.5.4 Flash EEPROM mapping through internal Memory Expansion
The Page Index register or PPAGE provides memory management for
the MC68HC912DG128. PPAGE consists of three bits to indicate which
physical location is active within the windows of the MC68HC912DG128.
The MC68HC912DG128 has a user’s program space window, a register
space window for Flash module registers, and a test program space
window.
The user’s program page window consists of 16K Flash EEPROM bytes.
One of eight pages is viewed through this window for a total of 128K
accessible Flash EEPROM bytes.
On the MC68HC912DG128, the register space window consists of a 4byte register block. One of four pages is viewed through this window for
each of the 32K flash module register blocks of MC68HC912DG128.
The test mode program page window consists of 32K Flash EEPROM
bytes. One of the four 32K byte arrays is viewed through this window for
a total 128K accessible Flash EEPROM bytes. This window is only
available in special mode for test purposes and replaces the user’s
program page window.
MC68HC912DG128 has a five pin port, Port K, for emulation and for
general purpose I/O. Three pins are used to emulate the three page
indices (PPAGE bits) and one pin is used as an emulation chip select.
When these four pins are not used for emulation they serve as general
purpose I/O pins. The fifth Port K pin is used as a general purpose I/O
pin.
5.5.5 Program space expansion
There are 128K bytes of Flash EEPROM. With a 64K byte address
space, the PPAGE register is needed to perform on-chip memory
expansion. A program space window of 16K byte pages is located from
$8000 to $BFFF. Three page indices are used to point to one of eight
different 16K byte pages. They can be viewed as expanded addresses
x16, x15 and x14.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Operating Modes
For More Information On This Product,
Go to: www.freescale.com
85
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Operating Modes
Table 5-3. Program space Page Index
Page Index 2
(PPAGE bit 2)
0
0
0
0
1
1
1
1
Page Index 1
(PPAGE bit 1)
0
0
1
1
0
0
1
1
Page Index 0
(PPAGE bit 0)
0
1
0
1
0
1
0
1
16K Program space Page
Flash array
16K byte Page 0
16K byte Page 1
16K byte Page 2
16K byte Page 3
16K byte Page 4
16K byte Page 5
16K byte Page 6*
16K byte Page 7*
00FEE32K
00FEE32K
01FEE32K
01FEE32K
10FEE32K
10FEE32K
11FEE32K
11FEE32K
* The 16K byte program space page 6 can also be accessed at a fixed
location from $4000 to $7FFF. The 16K byte program space page 7 can
also be accessed at a fixed location from $C000 to $FFFF.
5.5.6 Flash register space expansion
There are four 32K Flash arrays for MC68HC912DG128 and each
requires a 4-byte register block. A register space window is used to
access one of the four 4-byte blocks and the PPAGE register to map
each one into the window. The register space window is located from
$00F4 to $00F7 after reset. Only two page indices are used to point to
one of the four pages of the register space.
Table 5-4. Flash Register space Page Index
Page Index 2 Page Index 1
(PPAGE bit 2) (PPAGE bit 1)
0
0
0
1
1
0
1
1
Page Index 0
(PPAGE bit 0)
X
X
X
X
Flash register space Page
Flash array
$00F4-$00F7 Page 0
$00F4-$00F7 Page 1
$00F4-$00F7 Page 2
$00F4-$00F7 Page 3
00FEE32K
01FEE32K
10FEE32K
11FEE32K
Technical Data
86
MC68HC912DG128 — Rev 3.0
Operating Modes
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Operating Modes
Internal Resource Mapping
5.5.7 Test mode Program space expansion
In special mode and for test purposes only, the 128K bytes of Flash
EEPROM can be accessed through a test program space window of 32K
bytes. This window replaces the user’s program space window to be
able to access an entire array. In special mode and with ROMTST bit set
in MISC register, a program space is located from $8000 to $FFFF. Only
two page indices are used to point to one of the four 32K byte arrays.
They can be viewed as expanded addresses X16 and X15.
Table 5-5. Test mode program space Page Index
Page Index 2 Page Index 1 Page Index 0
(PPAGE bit 2) (PPAGE bit 1) (PPAGE bit 0)
0
0
X
0
1
X
1
0
X
1
1
X
Flash register space Page
Flash array
32K byte array Page 0
32K byte array Page 1
32K byte array Page 2
32K byte array Page 3
00FEE32K
01FEE32K
10FEE32K
11FEE32K
5.5.8 Page Index register descriptions
PORTK — Port K Data Register
$00FC
Bit 7
6
5
4
3
2
1
Bit 0
PORT
PK7
0
0
0
PK3
PK2
PK1
PK0
Emulation
ECS
0
0
0
-
PIX2
PIX1
PIX0
RESET:
-
0
0
0
-
-
-
-
Read and write anytime
Writing to the port does not change the pin states when it is configured
for page index emulation output.
This port is associated with the page index emulation pins. When the
port is not enabled to emulate page index, the port pins are used as
general-purpose I/O. Port K bit 3 is always a general purpose I/O pin.
This register is not in the memory map in peripheral or expanded modes
when the EMK control bit in MODE register is set.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Operating Modes
For More Information On This Product,
Go to: www.freescale.com
87
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Operating Modes
When selected as inputs, these pins can be configured to be high
impedance or pulled up.
ECS — Emulation Chip Select of selected program space
When this signal is active low it indicates that the program space is
accessed. This also applies to test mode program space. An access
is made if an address is in the program space window and either the
Flash or external memory is accessed. The ECS timing is E clock high
and can be stretched when accessing external memory depending on
the EXTR0 and EXTR1 bits in the MISC register. The ECS signal is
only active when the EMK bit is set.
PIX[2:0] — The content of the PPAGE register emulated externally.
This content indicates which Flash module register space is in the
memory map and which 16K byte Flash memory is in the program
space. In special mode and with ROMTST bit set, the content of the
Page Index register indicates which 32K byte Flash array is in the test
program space.
DDRK — Port K Data Direction Register
$00FD
Bit 7
6
5
4
3
2
1
Bit 0
DDK7
0
0
0
DDK3
DDK2
DDK1
DDK0
0
0
0
0
0
0
0
0
RESET:
Read and write: anytime.
This register determines the primary direction for each port K pin
configured as general-purpose I/O.
0 = Associated pin is a high-impedance input.
1 = Associated pin is an output.
This register is not in the map in peripheral or expanded modes when the
EMK control bit is set.
Technical Data
88
MC68HC912DG128 — Rev 3.0
Operating Modes
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Operating Modes
Internal Resource Mapping
PPAGE — (Program) Page Index Register
$00FF
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
PIX2
PIX1
PIX0
0
0
0
0
0
0
0
0
RESET:
Read and write: anytime.
This register determines the active page viewed through
MC68HC912DG128 windows.
CALL and RTC instructions have a special single wire mechanism to
read and write this register without using an address bus.
5.5.9 Miscellaneous System Control Register
Additional mapping and external resource controls are available. To use
external resources the part must be operated in one of the expanded
modes.
MISC — Miscellaneous Mapping Control Register
$0013
RESET:
Bit 7
ROMTST
0
6
NDRF
0
5
RFSTR1
0
4
RFSTR0
0
3
EXSTR1
1
2
EXSTR0
1
1
ROMHM
0
Bit 0
ROMON
0
RESET:
0
0
0
0
1
1
0
1
Mode
Exp mode
peripheral or
SC mode
Normal modes: write once; Special modes: write anytime. Read
anytime.
ROMTST — FLASH EEPROM Test mode
In normal modes, this bit is forced to zero.
0 = 16K window for Flash memory is located from $8000–$BFFF
1 = 32K window for Flash memory is located from $8000–$FFFF
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Operating Modes
For More Information On This Product,
Go to: www.freescale.com
89
Freescale Semiconductor, Inc.
Operating Modes
NDRF — Narrow Data Bus for Register-Following Map Space
This bit enables a narrow bus feature for the 1K 512 byte RegisterFollowing Map. This is useful for accessing 8-bit peripherals and
allows 8-bit and 16-bit external memory devices to be mixed in a
system. In Expanded Narrow (eight bit) modes, Single Chip Modes,
and Peripheral mode, this bit has no effect.
0 = Makes Register-Following MAP space act as a full 16 bit data bus.
Freescale Semiconductor, Inc...
1 = Makes the Register-Following MAP space act the same as an 8
bit only external data bus (data only goes through port A externally).
The Register-Following space is mapped from $0400 to $07FF after
reset, which is next to the register map. If the registers are moved this
space follows.
RFSTR1, RFSTR0 — Register Following Stretch
This two bit field determines the amount of clock stretch on accesses
to the 1K byte Register Following Map. It is valid regardless of the
state of the NDRF bit. In Single Chip and Peripheral Modes this bit
has no meaning or effect.
Table 5-6. RFSTR Stretch Bit Definition
RFSTR1
RFSTR0
Number of E Clocks
Stretched
0
0
0
0
1
1
1
0
2
1
1
3
Technical Data
90
MC68HC912DG128 — Rev 3.0
Operating Modes
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Operating Modes
Internal Resource Mapping
EXSTR1, EXSTR0 — External Access Stretch
This two bit field determines the amount of clock stretch on accesses
to the External Address Space. In Single Chip and Peripheral Modes
this bit has no meaning or effect.
Freescale Semiconductor, Inc...
Table 5-7. EXSTR Stretch Bit Definition
EXSTR1
EXSTR0
Number of E Clocks
Stretched
0
0
0
0
1
1
1
0
2
1
1
3
ROMHM — FLASH EEPROM only in second Half of Map
This bit has no meaning if ROMON bit is clear.
0 = The 16K byte of fixed Flash EEPROM in location $4000–$7FFF
can be accessed.
1 = Disables direct access to 16K byte Flash EEPROM from
$4000–$7FFF in the memory map. The physical location of
this16K byte Flash can still be accessed through the Program
Page window.
In special mode, with ROMTST bit set, this bit will allow overlap of the
four 32K Flash EEPROM arrays and overlap the four 4-byte Flash
register space in the same map space to be able to program all arrays
at the same time.
0 = The four 32K Flash arrays are accessed with four pages for
each.
1 = The four 32K Flash arrays coincide in the same space and are
selected at the same time for programming.
CAUTION:
Bit must be cleared before reading any of the arrays or registers.
ROMON — Enable FLASH EEPROM
These bits are used to enable the Flash EEPROM
0 = Disables Flash EEPROM in the memory map.
1 = Enables Flash EEPROM in the memory map.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Operating Modes
For More Information On This Product,
Go to: www.freescale.com
91
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Operating Modes
5.5.10 Mapping test registers
These registers are used for testing the mapping logic. They can only be
read and after each read they get cleared. A write to each register will
have no effect.
MTST0 — Mapping Test Register 0
RESET:
Bit 7
MT07
0
6
MT06
0
$00F8
5
MT05
0
4
MT04
0
3
MT03
0
2
MT02
0
1
MT01
0
Bit 0
MT00
0
MTST1 — Mapping Test Register 1
RESET:
Bit 7
MT0F
0
6
MT0E
0
$00F9
5
MT0D
0
4
MT0C
0
3
MT0B
0
2
MT0A
0
1
MT09
0
Bit 0
MT08
0
MTST2 — Mapping Test Register 2
RESET:
Bit 7
MT17
0
6
MT16
0
$00FA
5
MT15
0
4
MT14
0
3
MT13
0
2
MT12
0
1
MT11
0
Bit 0
MT10
0
MTST3 — Mapping Test Register 3
RESET:
Bit 7
MT1F
0
6
MT1E
0
$00FB
5
MT1D
0
4
MT1C
0
3
MT1B
0
2
MT1A
0
Technical Data
92
1
MT19
0
Bit 0
MT18
0
MC68HC912DG128 — Rev 3.0
Operating Modes
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Operating Modes
Memory Maps
5.6 Memory Maps
The following diagrams illustrate the memory map for each mode of
operation immediately after reset.
$0000
$03FF
$0000
$0400
$0800
$0FFF
$0800
$1000
$2000
$2000
$3FFF
$4000
$4000
$8000
REGISTERS
(MAPPABLE TO ANY 2K SPACE)
2K bytes EEPROM
(MAPPABLE TO ANY 4K SPACE)
8K bytes RAM
(MAPPABLE TO ANY 8K SPACE)
16K Fixed Flash EEPROM
$8000
16K Page Window
Eight 16K Flash EEPROM pages
$BFFF
$A000 - $BFFF Protected BOOT
at odd programing pages
$C000
16K Fixed Flash EEPROM
EXT
$C000
$E000 - $FFFF Protected BOOT
$FFFF
$FF00
$FF00
$FFFF
VECTORS
VECTORS
VECTORS
NORMAL
SINGLE CHIP
EXPANDED
SPECIAL
SINGLE CHIP
$FFFF
BDM
(if active)
Figure 5-1. Memory Map after reset
The following diagram illustrates the memory paging scheme.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Operating Modes
For More Information On This Product,
Go to: www.freescale.com
93
Freescale Semiconductor, Inc.
Operating Modes
$0000
$0400
$0800
$1000
$2000
$4000
6
Freescale Semiconductor, Inc...
16K Flash
(Unpaged)
One 16K Page accessible at a time (selected by PPAGE value = 0 to 7)
00 Flash 32K
$8000
0
01 Flash 32K
1
2
10 Flash 32K
3
11 Flash 32K *
4
5
6
7
16K Flash
(Paged)
(8K Boot)
$C000
(8K Boot)
(8K Boot)
7
* This 32K Flash
accessible as
pages 6 & 7 and
as unpaged
$4000 - $7FFF &
$C000 - $FFFF
16K Flash
(Unpaged)
$E000
(8K Boot)
$FF00
$FFFF
(8K Boot)
VECTORS
NORMAL
SINGLE CHIP
Figure 5-2. Memory Paging
Technical Data
94
MC68HC912DG128 — Rev 3.0
Operating Modes
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Section 6. Bus Control and Input/Output
6.1 Contents
6.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 95
6.3
Detecting Access Type from External Signals . . . . . . . . . . . . .95
6.4
Registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 96
6.2 Introduction
Internally the MC68HC912DG128 has full 16-bit data paths, but
depending upon the operating mode and control registers, the external
multiplexed bus may be 8 or 16 bits. There are cases where 8-bit and
16-bit accesses can appear on adjacent cycles using the LSTRB signal
to indicate 8- or 16-bit data.
It is possible to have a mix of 8 and 16 bit peripherals attached to the
external multiplexed bus, using the NDRF bit in the MISC register while
in expanded wide modes.
6.3 Detecting Access Type from External Signals
The external signals LSTRB, R/W, and A0 can be used to determine the
type of bus access that is taking place. Accesses to the internal RAM
module are the only type of access that produce LSTRB = A0 = 1,
because the internal RAM is specifically designed to allow misaligned
16-bit accesses in a single cycle. In these cases the data for the address
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Bus Control and Input/Output
For More Information On This Product,
Go to: www.freescale.com
95
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Bus Control and Input/Output
that was accessed is on the low half of the data bus and the data for
address + 1 is on the high half of the data bus.
Figure 6-1. Access Type vs. Bus Control Pins
LSTRB
1
0
1
0
0
A0
0
1
0
1
0
R/W
1
1
0
0
1
1
1
1
0
0
0
1
1
0
Type of Access
8-bit read of an even address
8-bit read of an odd address
8-bit write of an even address
8-bit write of an odd address
16-bit read of an even address
16-bit read of an odd address
(low/high data swapped)
16-bit write to an even address
16-bit write to an even address
(low/high data swapped)
6.4 Registers
Not all registers are visible in the MC68HC912DG128 memory map
under certain conditions. In special peripheral mode the first 16 registers
associated with bus expansion are removed from the memory map.
In expanded modes, some or all of port A, port B, and port E are used
for expansion buses and control signals. In order to allow emulation of
the single-chip functions of these ports, some of these registers must be
rebuilt in an external port replacement unit. In any expanded mode, port
A, and port B, are used for address and data lines so registers for these
ports, as well as the data direction registers for these ports, are removed
from the on-chip memory map and become external accesses.
In any expanded mode, port E pins may be needed for bus control (e.g.,
ECLK, R/W). To regain the single-chip functions of port E, the emulate
port E (EME) control bit in the MODE register may be set. In this special
case of expanded mode and EME set, PORTE and DDRE registers are
removed from the on-chip memory map and become external accesses
so port E may be rebuilt externally.
Technical Data
96
MC68HC912DG128 — Rev 3.0
Bus Control and Input/Output
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Bus Control and Input/Output
Registers
Bit 7
6
5
4
3
2
1
Bit 0
Single Chip
PA7
PA6
PA5
PA4
PA3
PA2
PA1
PA0
RESET:
—
—
—
—
—
—
—
—
Expanded
& Periph:
ADDR15/
DATA15
ADDR14/
DATA14
ADDR13/
DATA13
ADDR12/
DATA12
ADDR11/
DATA11
ADDR10/
DATA10
ADDR9/
DATA9
ADDR8/
DATA8
Expanded
narrow
ADDR15/
DATA15/
DATA7
ADDR14/
DATA14/
DATA6
ADDR13/
DATA13/
DATA5
ADDR12/
DATA12/
DATA4
ADDR11/
DATA11/
DATA3
ADDR10/
DATA10/
DATA2
ADDR9/
DATA9/
DATA1
ADDR8/
DATA8/
DATA0
PORTA — Port A Register
$0000
Bits PA[7:0] are associated respectively with addresses ADDR[15:8],
DATA[15:8] and DATA[7:0], in narrow mode. When this port is not used
for external addresses such as in single-chip mode, these pins can be
used as general-purpose I/O. DDRA determines the primary direction of
each pin. This register is not in the on-chip map in expanded and
peripheral modes. Read and write anytime.
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
DDA7
DDA6
DDA5
DDA4
DDA3
DDA2
DDA1
DDA0
0
0
0
0
0
0
0
0
DDRA — Port A Data Direction Register
$0002
This register determines the primary direction for each port A pin when
functioning as a general-purpose I/O port. DDRA is not in the on-chip
map in expanded and peripheral modes. Read and write anytime.
0 = Associated pin is a high-impedance input
1 = Associated pin is an output
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Bus Control and Input/Output
For More Information On This Product,
Go to: www.freescale.com
97
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Bus Control and Input/Output
Bit 7
6
5
4
3
2
1
Bit 0
Single Chip
PB7
PB6
PB5
PB4
PB3
PB2
PB1
PB0
RESET:
—
—
—
—
—
—
—
—
Expanded
& Periph:
ADDR7/
DATA7
ADDR6/
DATA6
ADDR5/
DATA5
ADDR4/
DATA4
ADDR3/
DATA3
ADDR2/
DATA2
ADDR1/
DATA1
ADDR0/
DATA0
Expanded
narrow
ADDR7
ADDR6
ADDR5
ADDR4
ADDR3
ADDR2
ADDR1
ADDR0
PORTB — Port B Register
$0001
Bits PB[7:0] are associated with addresses ADDR[7:0] and DATA[7:0]
(except in narrow mode) respectively. When this port is not used for
external addresses such as in single-chip mode, these pins can be used
as general-purpose I/O. DDRB determines the primary direction of each
pin. This register is not in the on-chip map in expanded and peripheral
modes. Read and write anytime.
Bit 7
6
5
4
3
2
1
Bit 0
DDB7
DDB6
DDB5
DDB4
DDB3
DDB2
DDB1
DDB0
0
0
0
0
0
0
0
0
RESET:
DDRB — Port B Data Direction Register
$0003
This register determines the primary direction for each port B pin when
functioning as a general-purpose I/O port. DDRB is not in the on-chip
map in expanded and peripheral modes. Read and write anytime.
0 = Associated pin is a high-impedance input
1 = Associated pin is an output
Technical Data
98
MC68HC912DG128 — Rev 3.0
Bus Control and Input/Output
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Bus Control and Input/Output
Registers
BIT 7
6
5
4
3
2
1
BIT 0
PE7
PE6
PE5
PE4
PE3
PE2
PE1
PE0
RESET:
—
—
—
—
—
—
—
—
Alt. Pin
Function
DBE or
ECLK or
CAL
MODB or
IPIPE1 or
CGMTST
MODA or
IPIPE0
ECLK
LSTRB or
TAGLO
R/W
IRQ
XIRQ
Freescale Semiconductor, Inc...
PORTE — Port E Register
$0008
This register is associated with external bus control signals and interrupt
inputs, including data bus enable (DBE), mode select (MODB/IPIPE1,
MODA/IPIPE0), E clock, size (LSTRB), read/write (R/W), IRQ, and
XIRQ. When the associated pin is not used for one of these specific
functions, the pin can be used as general-purpose I/O. The port E
assignment register (PEAR) selects the function of each pin. DDRE
determines the primary direction of each port E pin when configured to
be general-purpose I/O.
Some of these pins have software selectable pull-ups (DBE, LSTRB,
R/W, IRQ, and XIRQ). A single control bit enables the pull-ups for all
these pins which are configured as inputs.
This register is not in the map in peripheral mode or expanded modes
when the EME bit is set.
Read and write anytime.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Bus Control and Input/Output
For More Information On This Product,
Go to: www.freescale.com
99
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Bus Control and Input/Output
Bit 7
6
5
4
3
2
1
Bit 0
DDE7
DDE6
DDE5
DDE4
DDE3
DDE2
0
0
0
0
0
0
0
0
0
0
RESET:
DDRE — Port E Data Direction Register
$0009
This register determines the primary direction for each port E pin
configured as general-purpose I/O.
0 = Associated pin is a high-impedance input
1 = Associated pin is an output
PE[1:0] are associated with XIRQ and IRQ and cannot be configured as
outputs. These pins can be read regardless of whether the alternate
interrupt functions are enabled.
This register is not in the map in peripheral mode and expanded modes
while the EME control bit is set.
Read and write anytime.
BIT 7
6
5
4
3
2
1
BIT 0
NDBE
CGMTE
PIPOE
NECLK
LSTRE
RDWE
CALE
DBENE
RESET:
0
0
0
0
0
0
0
0
Normal
Expanded
RESET:
0
0
1
0
1
1
0
0
Special
Expanded
RESET:
1
1
0
1
0
0
0
0
Peripheral
RESET:
1
0
0
1
0
0
0
0
Normal
single chip
RESET:
0
0
1
0
1
1
0
0
Special
single chip
PEAR — Port E Assignment Register
$000A
The PEAR register is used to choose between the general-purpose I/O
functions and the alternate bus control functions of Port E. When an
Technical Data
100
MC68HC912DG128 — Rev 3.0
Bus Control and Input/Output
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Bus Control and Input/Output
Registers
alternate control function is selected, the associated DDRE bits are
overridden.
The reset condition of this register depends on the mode of operation
because bus -control signals are needed immediately after reset in some
modes.
In normal single-chip mode, no external bus control signals are needed
so all of port E is configured for general-purpose I/O.
Freescale Semiconductor, Inc...
In normal expanded modes, the reset vector is located in external
memory. The DBE and E clock are required for de-multiplexing address
and data, but LSTRB and R/W are only needed by the system when
there are external writable resources. Therefore in normal expanded
modes, only the DBE and E clock are configured for their alternate bus
control functions and the other bits of port E are configured for generalpurpose I/O. If the normal expanded system needs any other bus-control
signals, PEAR would need to be written before any access that needed
the additional signals.
In special expanded modes, DBE, IPIPE1, IPIPE0, E, LSTRB, and R/W
are configured as bus-control signals.
In special single chip modes, DBE, IPIPE1, IPIPE0, E, LSTRB, R/W, and
CALE are configured as bus-control signals.
In peripheral mode, the PEAR register is not accessible for reads or
writes. However, the CGMTE control bit is reset to one to configure PE6
as a test output from the PLL module.
NDBE — No Data Bus Enable
Normal: write once; Special: write anytime EXCEPT the first. Read
anytime.
0 = PE7 is used for DBE, external control of data enable on
memories, or inverted E clock.
1 = PE7 is the CAL function if CALE bit is set in PEAR register or
general-purpose I/O.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Bus Control and Input/Output
For More Information On This Product,
Go to: www.freescale.com
101
Freescale Semiconductor, Inc.
Bus Control and Input/Output
NDBE controls the use of the DBE pin of Port E. The NDBE bit has no
effect in Single Chip or Peripheral Modes. The associated pin will
default to the CAL function if the CALE bit is set in PEAR register or
otherwise to an I/O.
CGMTE — Clock Generator Module Testing Enable
Freescale Semiconductor, Inc...
Normal: write never; Special: write anytime EXCEPT the first. Read
anytime.
0 = PE6 is general-purpose I/O or pipe output.
1 = PE6 is a test signal output from the CGM module (no effect in
single chip or normal expanded modes). PIPOE = 1 overrides
this function and forces PE6 to be a pipe status output signal.
PIPOE — Pipe Status Signal Output Enable
Normal: write once; Special: write anytime EXCEPT the first time.
Read anytime.
0 = PE[6:5] are general-purpose I/O (if CGMTE = 1, PE6 is a test
output signal from the CGM module).
1 = PE[6:5] are outputs and indicate the state of the instruction
queue (only effective in expanded modes).
NECLK — No External E Clock
Normal single chip: write once; special single chip: write anytime; all
other modes: write never.
Read anytime. In peripheral mode, E is an input and in all other
modes, E is an output.
0 = PE4 is the external E-clock pin subject to the following
limitation: In single-chip modes, to get an E clock output signal,
it is necessary to have ESTR = 0 in addition to NECLK = 0. A
16-bit write to PEAR and MODE registers can configure all
three bits in one operation.
1 = PE4 is a general-purpose I/O pin.
Technical Data
102
MC68HC912DG128 — Rev 3.0
Bus Control and Input/Output
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Bus Control and Input/Output
Registers
LSTRE — Low Strobe (LSTRB) Enable
Normal: write once; Special: write anytime EXCEPT the first time.
Read anytime. This bit has no effect in single-chip modes or normal
expanded narrow mode.
0 = PE3 is a general-purpose I/O pin.
1 = PE3 is configured as the LSTRB bus-control output, provided
the MCU is not in single chip or normal expanded narrow
modes.
Freescale Semiconductor, Inc...
LSTRB is used during external writes. After reset in normal expanded
mode, LSTRB is disabled. If needed, it should be enabled before
external writes. External reads do not normally need LSTRB because
all 16 data bits can be driven even if the MCU only needs 8 bits of
data.
In normal expanded narrow mode this pin is reset to an output driving
high allowing the pin to be an output while in and immediately after
reset.
TAGLO is a shared function of the PE3/LSTRB pin. In special
expanded modes with LSTRE set and the BDM tagging on, a zero at
the falling edge of E tags the instruction word low byte being read into
the instruction queue.
RDWE — Read/Write Enable
Normal: write once; Special: write anytime EXCEPT the first time.
Read anytime. This bit has no effect in single-chip modes.
0 = PE2 is a general-purpose I/O pin.
1 = PE2 is configured as the R/W pin. In single chip modes, RDWE
has no effect and PE2 is a general-purpose I/O pin.
R/W is used for external writes. After reset in normal expanded mode,
it is disabled. If needed it should be enabled before any external
writes.
CALE — Calibration Reference Enable
Read and write anytime.
0 = Calibration reference is disabled and PE7 is general-purpose
I/O in single chip or peripheral modes or if the NDBE bit is set.
1 = Calibration reference is enabled on PE7 in single chip and
peripheral modes or if the NDBE bit is set.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Bus Control and Input/Output
For More Information On This Product,
Go to: www.freescale.com
103
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Bus Control and Input/Output
DBENE — DBE or Inverted E Clock on PE7
Normal modes: write once. Special modes: write anytime EXCEPT
the first; read anytime.
DBENE controls which signal is output on PE7 when NDBE control bit
is cleared. The inverted E clock output can be used to latch the
address for demultiplexing. It has the same behaviour as the E clock,
except it is inverted. Please note that in the case of idle expansion
bus, the ‘not E clock’ signal could stay high for many cycles.
The DBENE bit has no effect in single chip or peripheral modes and
PE7 is defaulted to the CAL function if the CALE bit is set in the PEAR
register or to an I/O otherwise.
0 = PE7 pin used for DBE external control of data enable on
memories in expanded modes when NDBE = 0
1 = PE7 pin used for inverted E clock output in expanded modes
when NDBE = 0
Bit 7
6
5
4
3
2
1
Bit 0
PUPK
PUPJ
PUPH
PUPE
0
0
PUPB
PUPA
0
0
0
1
0
0
0
0
RESET:
PUCR — Pull-Up Control Register
$000C
These bits select pull-up resistors for any pin in the corresponding port
that is currently configured as an input. This register is not in the map in
peripheral mode.
Read and write anytime.
PUPK — Pull-Up Port K Enable
0 = Port K pull-ups are disabled.
1 = Enable pull-up devices for all port K input pins.
PUPJ — Pull-Up or Pull-Down Port J Enable
0 = Port J resistive loads (pull-ups or pull-downs) are disabled.
1 = Enable resistive load devices (pull-ups or pull-downs) for all
port J input pins.
Technical Data
104
MC68HC912DG128 — Rev 3.0
Bus Control and Input/Output
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Bus Control and Input/Output
Registers
PUPH — Pull-Up or Pull-Down Port H Enable
0 = Port H resistive loads (pull-ups or pull-downs) are disabled.
1 = Enable resistive load devices (pull-ups or pull-downs) for all
port H input pins.
PUPE — Pull-Up Port E Enable
0 = Port E pull-ups on PE7, PE3, PE2, PE1 and PE0 are disabled.
1 = Enable pull-up devices for port E input pins PE7, PE3, PE2,
PE1 and PE0.
When this bit is set port E input pins 7, 3, 2, 1 and 0 have an active
pull-up device.
PUPB — Pull-Up Port B Enable
0 = Port B pull-ups are disabled.
1 = Enable pull-up devices for all port B input pins.
This bit has no effect if port B is being used as part of the address/data
bus (the pull-ups are inactive).
PUPA — Pull-Up Port A Enable
0 = Port A pull-ups are disabled.
1 = Enable pull-up devices for all port A input pins.
This bit has no effect if port B is being used as part of the address/data
bus (the pull-ups are inactive).
RDRIV — Reduced Drive of I/O Lines
RESET:
Bit 7
RDPK
0
6
RDPJ
0
5
RDPH
0
$000D
4
RDPE
0
3
0
0
2
0
0
1
RDPB
0
Bit 0
RDPA
0
These bits select reduced drive for the associated port pins. This
gives reduced power consumption and reduced RFI with a slight
increase in transition time (depending on loading). The reduced drive
function is independent of which function is being used on a particular
port.
This register is not in the map in peripheral mode.
Normal: write once; Special: write anytime EXCEPT the first time.
Read anytime.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Bus Control and Input/Output
For More Information On This Product,
Go to: www.freescale.com
105
Freescale Semiconductor, Inc.
Bus Control and Input/Output
RDPK — Reduced Drive of Port K
0 = All port K output pins have full drive enabled.
1 = All port K output pins have reduced drive capability.
RDPJ — Reduced Drive of Port J
0 = All port J output pins have full drive enabled.
1 = All port J output pins have reduced drive capability.
Freescale Semiconductor, Inc...
RDPH — Reduced Drive of Port H
0 = All port H output pins have full drive enabled.
1 = All port H output pins have reduced drive capability.
RDPE — Reduced Drive of Port E
0 = All port E output pins have full drive enabled.
1 = All port E output pins have reduced drive capability.
RDPB — Reduced Drive of Port B
0 = All port B output pins have full drive enabled.
1 = All port B output pins have reduced drive capability.
RDPA — Reduced Drive of Port A
0 = All port A output pins have full drive enabled.
1 = All port A output pins have reduced drive capability.
Technical Data
106
MC68HC912DG128 — Rev 3.0
Bus Control and Input/Output
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Section 7. Flash Memory
7.1 Contents
7.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 107
7.3
Future Flash EEPROM Support . . . . . . . . . . . . . . . . . . . . . . . 108
7.4
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 108
7.5
Flash EEPROM Control Block . . . . . . . . . . . . . . . . . . . . . . . . 109
7.6
Flash EEPROM Arrays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 109
7.7
Flash EEPROM Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . 110
7.8
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .115
7.9
Programming the Flash EEPROM . . . . . . . . . . . . . . . . . . . . . 118
7.10
Erasing the Flash EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . 120
7.11
Program/Erase Protection Interlocks . . . . . . . . . . . . . . . . . . .122
7.12
Stop or Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .122
7.13
Test Mode. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 123
7.2 Introduction
The four Flash EEPROM array modules 00FEE32K, 01FEE32K,
10FEE32K and 11FEE32K for the MC68HC912DG128 serve as
electrically erasable and programmable, non-volatile ROM emulation
memory. The modules can be used for program code that must either
execute at high speed or is frequently executed, such as operating
system kernels and standard subroutines, or they can be used for static
data which is read frequently. The Flash EEPROM is ideal for program
storage for single-chip applications allowing for field reprogramming.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Flash Memory
For More Information On This Product,
Go to: www.freescale.com
107
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Flash Memory
7.3 Future Flash EEPROM Support
Design is underway to introduce an improved 5V programming Flash
EEPROM module based on SuperFlash with integrated state machine
for simplified programming and erase to be introduced on the
68HC912DG128A.
Appendix: MC68HC912DG128A Flash contains detailed information to
assist in software planning for future Flash EEPROM compatibility and
easy transition to the 68HC912DG128A.
Read operation will be fully compatible with the present Flash EEPROM
design. Write and erase algorithms will be changed along with the
functions of the bits in the control register FEECTL
It is recommended that the flash algorithm not be stored as part of the
code but loaded and executed from RAM when required. This simplifies
compatibility issues and reduces the remote possibility of Flash
corruption in the unlikely event of runaway code.
The AUTO bit in the 68HC912DG128A Flash EEPROM control register
provides support for in-circuit detection of the NVM type — attempts to
set and clear this bit will only be successful on the 68HC912DG128A
where it will read as ‘1’ or ‘0’ as appropriate, on the 68HC912DG128A it
is tied to ‘0’.
To ensure full compatibility it is recommended that all of Appendix:
MC68HC912DG128A Flash be reviewed.
7.4 Overview
The Flash EEPROM array is arranged in a 16-bit configuration and may
be read as either bytes, aligned words or misaligned words. Access time
is one bus cycle for byte and aligned word access and two bus cycles for
misaligned word operations.
The Flash EEPROM module requires an external program/erase voltage
(VFP) to program or erase the Flash EEPROM array. The external
program/erase voltage is provided to the Flash EEPROM module via an
external VFP pin. To prevent damage to the flash array, VFP should
Technical Data
108
MC68HC912DG128 — Rev 3.0
Flash Memory
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Flash Memory
Flash EEPROM Control Block
always be within the specification as defined in Table 19-10 in Electrical
Specifications. Programming is by byte or aligned word. The Flash
EEPROM module supports bulk erase only.
The Flash EEPROM module has hardware interlocks which protect
stored data from accidental corruption. An erase- and programprotected 8-Kbyte block for boot routines is located at the top of each 32Kbyte array. Since boot programs must be available at all times, the only
useful boot block is at $E000–$FFFF location. All paged boot blocks can
be used as protected program space if desired.
7.5 Flash EEPROM Control Block
A 4-byte register block for each module controls the Flash EEPROM
module operation. Configuration information is specified and
programmed independently from the contents of the Flash EEPROM
array. At reset, the 4-byte register section starts at address $00F4 and
points to the 00FEE32K register block.
7.6 Flash EEPROM Arrays
After reset, a fixed 32K Flash EEPROM array, 11FEE32K, is located
from addresses $4000 to $7FFF and from $C000 to $FFFF. The other
three 32K Flash EEPROM arrays 00FEE32K, 01FEE32K and
10FEE32K, are mapped through a 16K byte program page window
located from addresses $8000 to $BFFF. The page window has eight
16K byte pages. The last two pages also map the physical location of the
fixed 32K Flash EEPROM array 11FEE32K. In expanded modes, the
Flash EEPROM arrays are turned off. See Operating Modes.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Flash Memory
For More Information On This Product,
Go to: www.freescale.com
109
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Flash Memory
7.7 Flash EEPROM Registers
Each 32K byte Flash EEPROM module has a set of registers. The
register space $00F4-$00F7 is in a register space window of four pages.
Each register page of four bytes maps the register space for each Flash
module and each page is selected by the PPAGE register. See
Operating Modes.
FEELCK — Flash EEPROM Lock Control Register
$00F4
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
LOCK
0
0
0
0
0
0
0
0
RESET:
In normal modes the LOCK bit can only be written once after reset.
LOCK — Lock Register Bit
0 = Enable write to FEEMCR register
1 = Disable write to FEEMCR register
FEEMCR — Flash EEPROM Module Configuration Register
$00F5
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
BOOTP
0
0
0
0
0
0
0
1
RESET:
This register controls the operation of the Flash EEPROM array.
BOOTP cannot be changed when the LOCK control bit in the
FEELCK register is set or if ENPE in the FEECTL register is set.
BOOTP — Boot Protect
The boot blocks are located at $E000–$FFFF and $A000–$BFFF for
odd program pages for each Flash EEPROM module. Since boot
programs must be available at all times, the only useful boot block is
at $E000–$FFFF location. All paged boot blocks can be used as
protected program space if desired.
0 = Enable erase and program of 8K byte boot block
1 = Disable erase and program of 8K byte boot block
Technical Data
110
MC68HC912DG128 — Rev 3.0
Flash Memory
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Flash Memory
Flash EEPROM Registers
FEETST — Flash EEPROM Module Test Register
RESET:
$00F6
Bit 7
6
5
4
3
2
1
Bit 0
FSTE
GADR
HVT
FENLV
FDISVFP
VTCK
STRE
MWPR
0
0
0
0
0
0
0
0
Freescale Semiconductor, Inc...
In normal mode, writes to FEETST control bits have no effect and always
read zero. The Flash EEPROM module cannot be placed in test mode
inadvertently during normal operation.
FSTE — Stress Test Enable
0 = Disables the gate/drain stress circuitry
1 = Enables the gate/drain stress circuitry
GADR — Gate/Drain Stress Test Select
0 = Selects the drain stress circuitry
1 = Selects the gate stress circuitry
HVT — Stress Test High Voltage Status
0 = High voltage not present during stress test
1 = High voltage present during stress test
FENLV — Enable Low Voltage
0 = Disables low voltage transistor in current reference circuit
1 = Enables low voltage transistor in current reference circuit
FDISVFP — Disable Status VFP Voltage Lock
When the VFP pin is below normal programming voltage the Flash
module will not allow writing to the LAT bit; the user cannot erase or
program the Flash module. The FDISVFP control bit enables writing
to the LAT bit regardless of the voltage on the VFP pin.
0 = Enable the automatic lock mechanism if VFP is low
1 = Disable the automatic lock mechanism if VFP is low
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Flash Memory
For More Information On This Product,
Go to: www.freescale.com
111
Freescale Semiconductor, Inc.
Flash Memory
VTCK — VT Check Test Enable
When VTCK is set, the Flash EEPROM module uses the VFP pin to
control the control gate voltage; the sense amp time-out path is
disabled. This allows for indirect measurements of the bit cells
program and erase threshold. If VFP < VZBRK (breakdown voltage) the
control gate will equal the VFP voltage.
If VFP > VZBRK the control gate will be regulated by the following
equation:
Freescale Semiconductor, Inc...
Vcontrol gate = VZBRK + 0.44 × (VFP − VZBRK)
0 = VT test disable
1 = VT test enable
STRE — Spare Test Row Enable
The spare test row consists of one Flash EEPROM array row. The
reserved word at location 31 contains production test information
which must be maintained through several erase cycles. When STRE
is set, the decoding for the spare test row overrides the address lines
which normally select the other rows in the array.
0 = LIB accesses are to the Flash EEPROM array
1 = Spare test row in array enabled if SMOD is active
MWPR — Multiple Word Programming
Used primarily for testing, if MWPR = 1, the two least-significant
address lines ADDR[1:0] will be ignored when programming a Flash
EEPROM location. The word location addressed if ADDR[1:0] = 00,
along with the word location addressed if ADDR[1:0] = 10, will both be
programmed with the same word data from the programming latches.
This bit should not be changed during programming.
0 = Multiple word programming disabled
1 = Program 32 bits of data
Technical Data
112
MC68HC912DG128 — Rev 3.0
Flash Memory
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Flash Memory
Flash EEPROM Registers
FEECTL — Flash EEPROM Control Register
RESET:
$00F7
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
FEESWAI
SVFP
ERAS
LAT
ENPE
0
0
0
0
0
0
0
0
This register controls the programming and erasure of the Flash
EEPROM.
Freescale Semiconductor, Inc...
FEESWAI — Flash EEPROM Stop in Wait Control
0 = Do not halt Flash EEPROM clock when the part is in wait mode.
1 = Halt Flash EEPROM clock when the part is in wait mode.
NOTE:
The FEESWAI bit cannot be asserted if the interrupt vector resides in the
Flash EEPROM array.
SVFP — Status VFP Voltage
SVFP is a read only bit.
0 = Voltage of VFP pin is below normal programming voltage levels
1 = Voltage of VFP pin is above normal programming voltage levels
ERAS — Erase Control
This bit can be read anytime or written when ENPE = 0. When set, all
locations in the array will be erased at the same time. The boot block
will be erased only if BOOTP = 0. This bit also affects the result of
attempted array reads. See Table 7-1 for more information. Status of
ERAS cannot change if ENPE is set.
0 = Flash EEPROM configured for programming
1 = Flash EEPROM configured for erasure
LAT — Latch Control
This bit can be read anytime or written when ENPE = 0. When set, the
Flash EEPROM is configured for programming or erasure and, upon
the next valid write to the array, the address and data will be latched
for the programming sequence. See Table 7-1 for the effects of LAT
on array reads. A high voltage detect circuit on the VFP pin will prevent
assertion of the LAT bit when the programming voltage is at normal
levels.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Flash Memory
For More Information On This Product,
Go to: www.freescale.com
113
Freescale Semiconductor, Inc.
Flash Memory
0 = Programming latches disabled
1 = Programming latches enabled
ENPE — Enable Programming/Erase
0 = Disables program/erase voltage to Flash EEPROM
1 = Applies program/erase voltage to Flash EEPROM
Freescale Semiconductor, Inc...
ENPE can be asserted only after LAT has been asserted and a write
to the data and address latches has occurred. If an attempt is made
to assert ENPE when LAT is negated, or if the latches have not been
written to after LAT was asserted, ENPE will remain negated after the
write cycle is complete.
The LAT, ERAS and BOOTP bits cannot be changed when ENPE is
asserted. A write to FEECTL may only affect the state of ENPE.
Attempts to read a Flash EEPROM array location in the Flash
EEPROM module while ENPE is asserted will not return the data
addressed. See Table 7-1 for more information.
Flash EEPROM module control registers may be read or written while
ENPE is asserted. If ENPE is asserted and LAT is negated on the
same write access, no programming or erasure will be performed.
Table 7-1. Effects of ENPE, LAT and ERAS on Array Reads
ENPE
0
0
0
1
LAT
0
1
1
–
ERAS
–
0
1
–
Result of Read
Normal read of location addressed
Read of location being programmed
Normal read of location addressed
Read cycle is ignored
Technical Data
114
MC68HC912DG128 — Rev 3.0
Flash Memory
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Flash Memory
Operation
7.8 Operation
The Flash EEPROM can contain program and data. On reset, it can
operate as a bootstrap memory to provide the CPU with internal
initialization information during the reset sequence.
7.8.1 Bootstrap Operation Single-Chip Mode
After reset, the CPU controlling the system will begin booting up by
fetching the first program address from address $FFFE.
7.8.2 Normal Operation
The Flash EEPROM allows a byte or aligned word read/write in one bus
cycle. Misaligned word read/write require an additional bus cycle. The
Flash EEPROM array responds to read operations only. Write
operations are ignored.
7.8.3 Program/Erase Operation
An unprogrammed Flash EEPROM bit has a logic state of one. A bit
must be programmed to change its state from one to zero. Erasing a bit
returns it to a logic one. The Flash EEPROM has a minimum
program/erase life of 100 cycles. Programming or erasing the Flash
EEPROM is accomplished by a series of control register writes and a
write to a set of programming latches.
Programming is restricted to a single byte or aligned word at a time as
determined by internal signal SZ8 and ADDR[0]. The Flash EEPROM
must first be completely erased prior to programming final data values.
It is possible to program a location in the Flash EEPROM without erasing
the entire array if the new value does not require the changing of bit
values from zero to one.
Read/Write Accesses During Program/Erase — During program or
erase operations, read and write accesses may be different from those
during normal operation and are affected by the state of the control bits
in the Flash EEPROM control register (FEECTL). The next write to any
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Flash Memory
For More Information On This Product,
Go to: www.freescale.com
115
Freescale Semiconductor, Inc.
Flash Memory
valid address to the array after LAT is set will cause the address and
data to be latched into the programming latches. Once the address and
data are latched, write accesses to the array will be ignored while LAT is
set. Writes to the control registers will occur normally.
Freescale Semiconductor, Inc...
Program/Erase Verification — When programming or erasing the
Flash EEPROM array, a special verification method is required to ensure
that the program/erase process is reliable, and also to provide the
longest possible life expectancy. This method requires stopping the
program/erase sequence at periods of tPPULSE (tEPULSE for erasing) to
determine if the Flash EEPROM is programmed/erased. After the
location reaches the proper value, it must continue to be
programmed/erased with additional margin pulses to ensure that it will
remain programmed/erased. Failure to provide the margin pulses could
lead to corrupted or unreliable data.
Program/Erase Sequence — To begin a program or erase sequence
the external VFP voltage must be applied and stabilized. The ERAS bit
must be set or cleared, depending on whether a program sequence or
an erase sequence is to occur. The LAT bit will be set to cause any
subsequent data written to a valid address within the Flash EEPROM to
be latched into the programming address and data latches. The next
Flash array write cycle must be either to the location that is to be
programmed if a programming sequence is being performed, or, if
erasing, to any valid Flash EEPROM array location. Writing the new
address and data information to the Flash EEPROM is followed by
assertion of ENPE to turn on the program/erase voltage to
program/erase the new location(s). The LAT bit must be asserted and
the address and data latched to allow the setting of the ENPE control bit.
If the data and address have not been latched, an attempt to assert
ENPE will be ignored and ENPE will remain negated after the write cycle
to FEECTL is completed. The LAT bit must remain asserted and the
ERAS bit must remain in its current state as long as ENPE is asserted.
A write to the LAT bit to clear it while ENPE is set will be ignored. That
is, after the write cycle, LAT will remain asserted. Likewise, an attempt
to change the state of ERAS will be ignored and the state of the ERAS
bit will remain unchanged.
Technical Data
116
MC68HC912DG128 — Rev 3.0
Flash Memory
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Flash Memory
Operation
The programming software is responsible for all timing during a program
sequence. This includes the total number of program pulses (nPP), the
length of the program pulse (tPPULSE), the program margin pulses (pm)
and the delay between turning off the high voltage and verifying the
operation (tVPROG).
Freescale Semiconductor, Inc...
The erase software is responsible for all timing during an erase
sequence. This includes the total number of erase pulses (em), the
length of the erase pulse (tEPULSE), the erase margin pulse or pulses,
and the delay between turning off the high voltage and verifying the
operation (tVERASE).
Software also controls the supply of the proper program/erase voltage to
the VFP pin, and should be at the proper level before ENPE is set during
a program/erase sequence.
A program/erase cycle should not be in progress when starting another
program/erase, or while attempting to read from the array.
NOTE:
Although clearing ENPE disables the program/erase voltage (VFP) from
the VFP pin to the array, care must be taken to ensure that VFP is at VDD
whenever programming/erasing is not in progress. Not doing so could
damage the part. Ensuring that VFP is always greater or equal to VDD
can be accomplished by controlling the VFP power supply with the
programming software via an output pin. Alternatively, all programming
and erasing can be done prior to installing the device on an application
circuit board which can always connect VFP to VDD. Programming can
also be accomplished by plugging the board into a special programming
fixture which provides program/erase voltage to the VFP pin.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Flash Memory
For More Information On This Product,
Go to: www.freescale.com
117
Freescale Semiconductor, Inc.
Flash Memory
7.9 Programming the Flash EEPROM
Programming the Flash EEPROM is accomplished by the following
sequence. The VFP pin voltage must be at the proper level prior to
executing step 4 the first time.
1. Apply program/erase voltage to the VFP pin.
Freescale Semiconductor, Inc...
2. Set the PPAGE to point to the 16K Flash window to be
programmed and corresponding register block. Clear ERAS and
set the LAT bit in the FEECTL register to establish program mode
and enable programming address and data latches.
3. Write data to a valid address. The address and data is latched. If
BOOTP is asserted, an attempt to program an address in the boot
block will be ignored.
4. Apply programming voltage by setting ENPE.
5. Delay for one programming pulse (tPPULSE).
6. Remove programming voltage by clearing ENPE.
7. Delay while high voltage is turning off (tVPROG).
8. Read the address location to verify that it has been programmed
9. If the location is not programmed, repeat steps 4 through 7 until
the location is programmed or until the specified maximum
number of program pulses has been reached (nPP)
10. If the location is programmed, repeat the same number of pulses
as required to program the location. This provides 100% program
margin.
11. Read the address location to verify that it remains programmed.
12. Clear LAT.
13. If there are more locations to program, repeat steps 2 through 10.
14. Turn off VFP (reduce voltage on VFP pin to VDD).
The flowchart in Figure 7-1 demonstrates the recommended
programming sequence.
Technical Data
118
MC68HC912DG128 — Rev 3.0
Flash Memory
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Flash Memory
Programming the Flash EEPROM
START PROG
TURN ON VFP
CLEAR MARGIN FLAG
CLEAR PROGRAM PULSE COUNTER (nPP)
WRITE PPAGE
CLEAR ERAS
SET LAT
Freescale Semiconductor, Inc...
WRITE DATA
TO ADDRESS
SET ENPE
DELAY FOR DURATION
OF PROGRAM PULSE
(tPPULSE)
CLEAR ENPE
SET
MARGIN FLAG
DELAY BEFORE VERIFY
(tVPROG)
IS
MARGIN FLAG
SET?
INCREMENT
nPP COUNTER
READ
LOCATION
NO
YES
DECREMENT
nPP COUNTER
DATA
CORRECT?
YES
NO
NO
nPP = 0?
nPP = 50?
YES
DATA
CORRECT?
NO
YES
NO
YES
CLEAR LAT
GET NEXT
ADDRESS/DATA
NO
LOCATION FAILED
TO PROGRAM
DONE?
YES
TURN OFF VFP
DONE PROG
Figure 7-1. Program Sequence Flow
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Flash Memory
For More Information On This Product,
Go to: www.freescale.com
119
Freescale Semiconductor, Inc.
Flash Memory
7.10 Erasing the Flash EEPROM
The following sequence demonstrates the recommended procedure for
erasing any of the Flash EEPROM. The VFP pin voltage must be at the
proper level prior to executing step 4 the first time.
1. Turn on VFP (apply program/erase voltage to the VFP pin).
Freescale Semiconductor, Inc...
2. Set the PPAGE register to point to the 32K Flash array to be
erased. Set the LAT bit and ERAS bit to configure the Flash
EEPROM for erasing.
3. Write to any valid address in the 32K Flash array. This allows the
erase voltage to be turned on; the data written and the address
written are not important. The boot block will be erased only if the
control bit BOOTP is negated.
4. Apply erase voltage by setting ENPE.
5. Delay for a single erase pulse (tEPULSE).
6. Remove erase voltage by clearing ENPE.
7. Delay while high voltage is turning off (tVERASE).
8. Read the entire array to ensure that the Flash EEPROM is erased.
9. If all of the Flash EEPROM locations are not erased, repeat steps
4 through 7 until either the remaining locations are erased, or until
the maximum erase pulses have been applied (nEP)
10. If all of the Flash EEPROM locations are erased, repeat the same
number of pulses as required to erase the array. This provides
100% erase margin.
11. Read the entire array to ensure that the Flash EEPROM is erased.
12. Clear LAT.
13. Turn off VFP (reduce voltage on VFP pin to VDD).
The flowchart in Figure 7-2 demonstrates the recommended erase
sequence.
Technical Data
120
MC68HC912DG128 — Rev 3.0
Flash Memory
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Flash Memory
Erasing the Flash EEPROM
START ERASE
TURN ON VFP
CLEAR MARGIN FLAG
CLEAR ERASE PULSE COUNTER (nEP)
WRITE PPAGE
SET ERAS
SET LAT
Freescale Semiconductor, Inc...
WRITE TO ARRAY
SET ENPE
DELAY FOR DURATION
OF ERASE PULSE
(tEPULSE)
CLEAR ENPE
SET
MARGIN FLAG
DELAY BEFORE VERIFY
(tVERASE)
IS
MARGIN FLAG
SET?
NO
INCREMENT
nEP COUNTER
READ
ARRAY
YES
DECREMENT
nEP COUNTER
ARRAY
ERASED?
YES
NO
NO
nEP = 0?
nEP = 5?
YES
YES
NO
ARRAY
ERASED?
NO
YES
CLEAR LAT
TURN OFF VFP
ARRAY ERASED
ARRAY FAILED TO ERASE
Figure 7-2. Erase Sequence Flow
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Flash Memory
For More Information On This Product,
Go to: www.freescale.com
121
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Flash Memory
7.11 Program/Erase Protection Interlocks
The Flash EEPROM program and erase mechanisms provide maximum
protection from accidental programming or erasure.
The voltage required to program/erase the Flash EEPROM (VFP) is
supplied via an external pin. If VFP is not present, no
programming/erasing will occur. Furthermore, the program/erase
voltage will not be applied to the Flash EEPROM unless turned on by
setting a control bit (ENPE). The ENPE bit may not be set unless the
programming address and data latches have been written previously
with a valid address. The latches may not be written unless enabled by
setting a control bit (LAT). The LAT and ENPE control bits must be
written on separate writes to the control register (FEECTL) and must be
separated by a write to the programming latches. The ERAS and LAT
bits are also protected when ENPE is set. This prevents inadvertent
switching between erase/program mode and also prevents the latched
data and address from being changed after a program cycle has been
initiated.
7.12 Stop or Wait Mode
When stop or wait commands are executed, the MCU puts the Flash
EEPROM in stop or wait mode. In these modes the Flash module will
cease erasure or programming immediately. It is advised not to enter
stop or wait modes when programming the Flash array.
CAUTION:
The Flash EEPROM module requires a 250nsec delay for wake-up from
STOP mode. If the operating bus frequency is greater than 4MHz, the
Flash cannot be used when recovering from STOP mode when the DLY
bit in the INTCR register is cleared.
Technical Data
122
MC68HC912DG128 — Rev 3.0
Flash Memory
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Flash Memory
Test Mode
7.13 Test Mode
Freescale Semiconductor, Inc...
The Flash EEPROM has some special test functions which are only
accessible when the device is in test mode. Test mode is indicated to the
Flash EEPROM module when the SMOD line on the LIB is asserted.
When SMOD is asserted, the special test control bits may be accessed
via the LIB to invoke the special test functions in the Flash EEPROM
module. When SMOD is not asserted, writes to the test control bits have
no effect and all bits in the test register FEETST will be cleared. This
ensures that Flash EEPROM test mode cannot be invoked inadvertently
during normal operation.
Note that the Flash EEPROM module will operate normally, even if
SMOD is asserted, until a special test function is invoked. The test mode
adds additional features over normal mode which allow the tests to be
performed even after the device is installed in the final product.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Flash Memory
For More Information On This Product,
Go to: www.freescale.com
123
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Flash Memory
Technical Data
124
MC68HC912DG128 — Rev 3.0
Flash Memory
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Section 8. EEPROM Memory
8.1 Contents
8.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 125
8.3
Future EEPROM Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . 126
8.4
EEPROM Programmer’s Model . . . . . . . . . . . . . . . . . . . . . . . 127
8.5
EEPROM Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 128
8.2 Introduction
The MC68HC912DG128 EEPROM nonvolatile memory is arranged in a
16-bit configuration. The EEPROM array may be read as either bytes,
aligned words or misaligned words. Access times are one bus cycle for
byte and aligned word access and two bus cycles for misaligned word
operations.
Programming is by byte or aligned word. Attempts to program or erase
misaligned words will fail. Only the lower byte will be latched and
programmed or erased. Programming and erasing of the user EEPROM
can be done in all modes.
Each EEPROM byte or aligned word must be erased before
programming. The EEPROM module supports byte, aligned word, row
(32 bytes) or bulk erase, all using the internal charge pump. The
EEPROM module has hardware interlocks which protect stored data
from corruption by accidentally enabling the program/erase voltage.
Programming voltage is derived from the internal VDD supply with an
internal charge pump.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
EEPROM Memory
For More Information On This Product,
Go to: www.freescale.com
125
Freescale Semiconductor, Inc.
EEPROM Memory
8.3 Future EEPROM Support
Design is underway to introduce an improved EEPROM module with
integrated state machine to simplify programming and erase. This will be
introduced on the 68HC912DG128A together with 5V programming
Flash EEPROM.
Freescale Semiconductor, Inc...
Appendix: MC68HC912DG128A EEPROM contains detailed
information to assist in software planning for future EEPROM
compatibility and transition to the 68HC912DG128A. Read, write and
erase algorithms are fully compatible with the present EEPROM design.
The key change comes in the form of a self timed state machine for
erasing & writing data. This is implemented using a pre-scaler loaded
from a new word register EEDIV ($00EE) - located in a presently unused
location this register can be written without effect, reading the location
will return unpredictable data.
Adding 5 bytes of initialisation code to current software to load EEDIV
(with value appropriate for the application’s crystal frequency, EXTALi)
will help ensure compatibility.
Other new features for performance improvement are disabled at reset
providing a compatible algorithm for modifying the EEPROM.
CAUTION:
Other areas for consideration include:
Program/Erase is not guaranteed in Limp home mode. Clock monitor
CME bit must be enabled during program/erase.
Program/erase should not be performed with input clock frequency <250
KHz.
Resonator/crystal frequency tolerance should be better than 2% total for
< 2MHz, 3% total for >= 2MHz.
Successive writes to an EEPROM location must be preceded by an
erase cycle.
To ensure full compatibility it is recommended that all of Appendix:
MC68HC912DG128A EEPROM be reviewed.
Technical Data
126
MC68HC912DG128 — Rev 3.0
EEPROM Memory
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
EEPROM Memory
EEPROM Programmer’s Model
8.4 EEPROM Programmer’s Model
The EEPROM module consists of two separately addressable sections.
The first is a four-byte memory mapped control register block used for
control, testing and configuration of the EEPROM array. The second
section is the EEPROM array itself.
Freescale Semiconductor, Inc...
At reset, the four-byte register section starts at address $00F0 and the
EEPROM array is located from addresses $0800 to $0FFF. For
information on re-mapping the register block and EEPROM address
space, refer to Operating Modes.
Read/write access to the memory array section can be enabled or
disabled by the EEON control bit in the INITEE register. This feature
allows the access to memory mapped resources with lower priority than
the EEPROM memory array. EEPROM control registers can be accessed
regardless of the state of EEON. Any EEPROM erase or program
operations already in progress will not be affected by modifying EEON.
Using the normal EEPROG control, it is possible to continue
program/erase operations during WAIT. For lowest power consumption
during WAIT, stop program/erase by turning off EEPGM.
If the STOP mode is entered during programming or erasing,
program/erase voltage will be automatically turned off and the RC clock
(if enabled) is stopped. However, the EEPGM control bit will remain set.
When STOP mode is terminated, the program/erase voltage will be
automatically turned back on if EEPGM is set.
At low bus frequencies, the RC clock must be turned on for
program/erase.
The EEPROM module contains an extra byte called SHADOW byte
which is loaded at reset into the EEMCR register.
To program the SHADOW byte, when in special modes (SMODN=0), the
NOSHB bit in EEMCR register must be cleared. Normal programming
routines are used to program the SHADOW byte which becomes
accessible at address $0FC0 when NOSHB is cleared.
At the next reset the SHADOW byte data is loaded into the EEMCR.
The SHADOW byte can be protected from being programmed or erased
by setting the SHPROT bit of EEPROT register.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
EEPROM Memory
For More Information On This Product,
Go to: www.freescale.com
127
Freescale Semiconductor, Inc.
EEPROM Memory
8.5 EEPROM Control Registers
EEMCR — EEPROM Module Configuration
RESET:
$00F0
Bit 7
6
5
4
3
2
1
Bit 0
NOBDML
NOSHB
EESWAI
PROTLCK
EERC
—(2)
1(1)
—(2)
1
—(2)
1(1)
—(2)
1
1
0
0
1. Bits 4 and 5 have test functions and should not be programmed.
2. Loaded from SHADOW byte.
Bits[7:4] are loaded at reset from the EEPROM SHADOW byte.
Freescale Semiconductor, Inc...
NOTE:
Bits 5 and 4 are reserved for test purposes. These locations in the
SHADOW byte should not be programmed otherwise some locations in
the regular EEPROM array will no longer be visible.
NOBDML — Background Debug Mode Lockout Disable
0 = The BDM lockout is enabled.
1 = The BDM lockout is disabled.
Loaded from SHADOW byte at reset.
Read anytime. Write anytime in special modes (SMODN=0).
NOSHB — SHADOW Byte Disable
0 = SHADOW byte enabled and accessible at address $0FC0.
1 = Regular EEPROM array at address $0FC0.
Loaded from SHADOW byte at reset.
Read anytime. Write anytime in special modes (SMODN=0).
When NOSHB cleared, the regular EEPROM array byte at address
$0FC0 is no longer visible. The SHADOW byte is accessed instead
for both read and program/erase operations. BULK, ODD and EVEN
program/erase only apply if the SHADOW byte is enabled.
NOTE:
Bit 6 of the SHADOW byte should not be cleared (set to ‘0’) in order to
have the full EEPROM array visible.
EESWAI — EEPROM Stops in Wait Mode
0 = The module is not affected during WAIT mode
1 = The module ceases to be clocked during WAIT mode
Read and write anytime.
NOTE:
The EESWAI bit should be cleared if the WAIT mode vectors are
mapped in the EEPROM array.
Technical Data
128
MC68HC912DG128 — Rev 3.0
EEPROM Memory
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
EEPROM Memory
EEPROM Control Registers
PROTLCK — Block Protect Write Lock
0 = Block protect bits and bulk erase protection bit can be written
1 = Block protect bits are locked
Read anytime. Write once in normal modes (SMODN = 1), set and
clear any time in special modes (SMODN = 0).
EERC — EEPROM Charge Pump Clock
0 = System clock is used as clock source for the internal charge
pump. Internal RC oscillator is stopped.
1 = Internal RC oscillator drives the charge pump. The RC oscillator
is required when the system bus clock is lower than fPROG.
Read and write anytime.
EEPROT — EEPROM Block Protect
RESET:
Bit 7
SHPROT
1
6
1
1
$00F1
5
BPROT5
1
4
BPROT4
1
3
BPROT3
1
2
BPROT2
1
1
BPROT1
1
Bit 0
BPROT0
1
Prevents accidental writes to EEPROM. Read anytime. Write anytime if
EEPGM = 0 and PROTLCK = 0.
SHPROT — SHADOW Byte Protection
0 = The SHADOW byte can be programmed and erased.
1 = The SHADOW byte is protected from being programmed and
erased.
BPROT[5:0] — EEPROM Block Protection
0 = Associated EEPROM block can be programmed and erased.
1 = Associated EEPROM block is protected from being
programmed and erased.
Table 8-1. 2K byte EEPROM Block Protection
Bit Name
BPROT5
BPROT4
BPROT3
BPROT2
BPROT1
BPROT0
Block Protected
$0800 to $0BFF
$0C00 to $0DFF
$0E00 to $0EFF
$0F00 to $0F7F
$0F80 to $0FBF
$0FC0 to $0FFF
MC68HC912DG128 — Rev 3.0
MOTOROLA
Block Size
1024 Bytes
512 Bytes
256 Bytes
128 Bytes
64 Bytes
64 Bytes
Technical Data
EEPROM Memory
For More Information On This Product,
Go to: www.freescale.com
129
Freescale Semiconductor, Inc.
EEPROM Memory
EETST — EEPROM Test
RESET:
Bit 7
EEODD
0
$00F2
6
EEVEN
0
5
MARG
0
4
EECPD
0
3
EECPRD
0
2
0
0
1
EECPM
0
Bit 0
0
0
Read anytime. Write in special modes only (SMODN = 0). These bits are
used for test purposes only. In normal modes the bits are forced to zero.
Freescale Semiconductor, Inc...
EEODD — Odd Row Programming
0 = Odd row bulk programming/erasing is disabled.
1 = Bulk program/erase all odd rows.
EEVEN — Even Row Programming
0 = Even row bulk programming/erasing is disabled.
1 = Bulk program/erase all even rows.
MARG — Program and Erase Voltage Margin Test Enable
0 = Normal operation.
1 = Program and Erase Margin test.
This bit is used to evaluate the program/erase voltage margin.
EECPD — Charge Pump Disable
0 = Charge pump is turned on during program/erase.
1 = Disable charge pump.
EECPRD — Charge Pump Ramp Disable
Known to enhance write/erase endurance of EEPROM cells.
0 = Charge pump is turned on progressively during program/erase.
1 = Disable charge pump controlled ramp up.
EECPM — Charge Pump Monitor Enable
0 = Normal operation.
1 = Output the charge pump voltage on the IRQ/VPP pin.
Technical Data
130
MC68HC912DG128 — Rev 3.0
EEPROM Memory
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
EEPROM Memory
EEPROM Control Registers
EEPROG — EEPROM Control
RESET:
Bit 7
BULKP
1
6
0
0
$00F3
5
0
0
4
BYTE
0
3
ROW
0
2
ERASE
0
1
EELAT
0
Bit 0
EEPGM
0
BULKP — Bulk Erase Protection
0 = EEPROM can be bulk erased.
1 = EEPROM is protected from being bulk or row erased.
Read anytime. Write anytime if EEPGM = 0 and PROTLCK = 0.
Freescale Semiconductor, Inc...
BYTE — Byte and Aligned Word Erase
0 = Bulk or row erase is enabled.
1 = One byte or one aligned word erase only.
Read anytime. Write anytime if EEPGM = 0.
ROW — Row or Bulk Erase (when BYTE = 0)
0 = Erase entire EEPROM array.
1 = Erase only one 32-byte row.
Read anytime. Write anytime if EEPGM = 0.
BYTE and ROW have no effect when ERASE = 0
Table 8-2. Erase Selection
BYTE
0
0
1
1
ROW
0
1
0
1
Block size
Bulk erase entire EEPROM array
Row erase 32 bytes
Byte or aligned word erase
Byte or aligned word erase
If BYTE = 1 and test mode is not enabled, only the location specified
by the address written to the programming latches will be erased. The
operation will be a byte or an aligned word erase depending on the
size of written data.
ERASE — Erase Control
0 = EEPROM configuration for programming.
1 = EEPROM configuration for erasure.
Read anytime. Write anytime if EEPGM = 0.
Configures the EEPROM for erasure or programming.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
EEPROM Memory
For More Information On This Product,
Go to: www.freescale.com
131
Freescale Semiconductor, Inc.
EEPROM Memory
When test mode is not enabled and unless BULKP is set, erasure is
by byte, aligned word, row or bulk.
EELAT — EEPROM Latch Control
0 = EEPROM set up for normal reads.
1 = EEPROM address and data bus latches set up for
programming or erasing.
Read anytime. Write anytime if EEPGM = 0.
Freescale Semiconductor, Inc...
BYTE, ROW, ERASE and EELAT bits can be written simultaneously
or in any sequence.
EEPGM — Program and Erase Enable
0 = Disables program/erase voltage to EEPROM.
1 = Applies program/erase voltage to EEPROM.
The EEPGM bit can be set only after EELAT has been set. When
EELAT and EEPGM are set simultaneously, EEPGM remains clear
but EELAT is set.
The BULKP, BYTE, ROW, ERASE and EELAT bits cannot be
changed when EEPGM is set. To complete a program or erase, two
successive writes to clear EEPGM and EELAT bits are required
before reading the programmed data. A write to an EEPROM location
has no effect when EEPGM is set. Latched address and data cannot
be modified during program or erase.
A program or erase operation should follow the sequence below:
1. Write BYTE, ROW and ERASE to the desired value, write EELAT
=1
2. Write a byte or an aligned word to an EEPROM address
3. Write EEPGM = 1
4. Wait for programming (tPROG) or erase (terase) delay time
5. Write EEPGM = 0
6. Write EELAT = 0
It is possible to program/erase more bytes or words without intermediate
EEPROM reads, by jumping from step 5 to step 2.
Technical Data
132
MC68HC912DG128 — Rev 3.0
EEPROM Memory
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Section 9. Resets and Interrupts
9.1 Contents
9.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 133
9.3
Maskable interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
9.4
Latching of Interrupts . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 134
9.5
Interrupt Control and Priority Registers . . . . . . . . . . . . . . . . . 135
9.6
Interrupt test registers. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
9.7
Resets. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .137
9.8
Effects of Reset . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 138
9.9
Register Stacking . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 140
9.10
Important User Information . . . . . . . . . . . . . . . . . . . . . . . . . . . 142
9.2 Introduction
CPU12 exceptions include resets and interrupts. Each exception has an
associated 16-bit vector, which points to the memory location where the
routine that handles the exception is located. Vectors are stored in the
upper 128 bytes of the standard 64K byte address map.
The six highest vector addresses are used for resets and non-maskable
interrupt sources. The remainder of the vectors are used for maskable
interrupts, and all must be initialized to point to the address of the
appropriate service routine.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
133
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Resets and Interrupts
9.2.1 Exception Priority
A hardware priority hierarchy determines which reset or interrupt is
serviced first when simultaneous requests are made. Six sources are not
maskable. The remaining sources are maskable, and any one of them
can be given priority over other maskable interrupts.
The priorities of the non-maskable sources are:
1. POR or RESET pin
2. Clock monitor reset
3. COP watchdog reset
4. Unimplemented instruction trap
5. Software interrupt instruction (SWI)
6. XIRQ signal (if X bit in CCR = 0)
9.3 Maskable interrupts
Maskable interrupt sources include on-chip peripheral systems and
external interrupt service requests. Interrupts from these sources are
recognized when the global interrupt mask bit (I) in the CCR is cleared.
The default state of the I bit out of reset is one, but it can be written at
any time.
Interrupt sources are prioritized by default but any one maskable
interrupt source may be assigned the highest priority by means of the
HPRIO register. The relative priorities of the other sources remain the
same.
An interrupt that is assigned highest priority is still subject to global
masking by the I bit in the CCR, or by any associated local bits. Interrupt
vectors are not affected by priority assignment. HPRIO can only be
written while the I bit is set (interrupts inhibited). Table 9-1 lists interrupt
sources and vectors in default order of priority.
Before masking an interrupt by clearing the corresponding local enable
bit, the I-bit should be set in order to avoid an SWI.
Technical Data
134
MC68HC912DG128 — Rev 3.0
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Resets and Interrupts
Latching of Interrupts
9.4 Latching of Interrupts
XIRQ is always level triggered and IRQ can be selected as a level
triggered interrupt. These level triggered interrupt pins should only be
released during the appropriate interrupt service routine. Generally the
interrupt service routine will handshake with the interrupting logic to
release the pin. In this way, the MCU will never start the interrupt service
sequence only to determine that there is no longer an interrupt source.
In the event that this does occur the trap vector will be taken.
If IRQ is selected as an edge triggered interrupt, the hold time of the level
after the active edge is independent of when the interrupt is serviced. As
long as the minimum hold time is met, the interrupt will be latched inside
the MCU. In this case the IRQ edge interrupt latch is cleared
automatically when the interrupt is serviced.
All of the remaining interrupts are latched by the MCU with a flag bit.
These interrupt flags should be cleared during an interrupt service
routine or when interrupts are masked by the I bit. By doing this, the
MCU will never get an unknown interrupt source and take the trap vector.
Table 9-1. Interrupt Vector Map
Vector Address
$FFFE, $FFFF
$FFFC, $FFFD
$FFFA, $FFFB
$FFF8, $FFF9
$FFF6, $FFF7
$FFF4, $FFF5
$FFF2, $FFF3
$FFF0, $FFF1
$FFEE, $FFEF
$FFEC, $FFED
$FFEA, $FFEB
$FFE8, $FFE9
$FFE6, $FFE7
$FFE4, $FFE5
$FFE2, $FFE3
$FFE0, $FFE1
$FFDE, $FFDF
$FFDC, $FFDD
Interrupt Source
Reset
Clock monitor fail reset
COP failure reset
Unimplemented instruction trap
SWI
XIRQ
IRQ
Real time interrupt
Timer channel 0
Timer channel 1
Timer channel 2
Timer channel 3
Timer channel 4
Timer channel 5
Timer channel 6
Timer channel 7
Timer overflow
Pulse accumulator overflow
CCR
Mask
None
None
None
None
None
X bit
I bit
I bit
I bit
I bit
I bit
I bit
I bit
I bit
I bit
I bit
I bit
I bit
Local Enable
None
COPCTL (CME, FCME)
COP rate selected
None
None
None
INTCR (IRQEN)
RTICTL (RTIE)
TMSK1 (C0I)
TMSK1 (C1I)
TMSK1 (C2I)
TMSK1 (C3I)
TMSK1 (C4I)
TMSK1 (C5I)
TMSK1 (C6I)
TMSK1 (C7I)
TMSK2 (TOI)
PACTL (PAOVI)
MC68HC912DG128 — Rev 3.0
MOTOROLA
HPRIO Value to
Elevate
–
–
–
–
–
–
$F2
$F0
$EE
$EC
$EA
$E8
$E6
$E4
$E2
$E0
$DE
$DC
Technical Data
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
135
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Resets and Interrupts
Table 9-1. Interrupt Vector Map
Vector Address
Interrupt Source
CCR
Mask
I bit
I bit
$FFDA, $FFDB
$FFD8, $FFD9
Pulse accumulator input edge
SPI serial transfer complete
$FFD6, $FFD7
SCI 0
I bit
$FFD4, $FFD5
SCI 1
I bit
$FFD2, $FFD3
$FFD0, $FFD1
ATD0 or ATD1
MSCAN 0 wake-up
I bit
I bit
$FFCE, $FFCF
Key wake-up J or H
I bit
$FFCC, $FFCD
$FFCA, $FFCB
Modulus down counter underflow
Pulse Accumulator B Overflow
I bit
I bit
$FFC8, $FFC9
MSCAN 0 errors
I bit
$FFC6, $FFC7
$FFC4, $FFC5
$FFC2, $FFC3
$FFC0, $FFC1
$FFBE, $FFBF
MSCAN 0 receive
MSCAN 0 transmit
CGM lock and limp home
IIC Bus
MSCAN 1 wake-up
I bit
I bit
I bit
I bit
I bit
$FFBC, $FFBD
MSCAN 1 errors
I bit
$FFBA, $FFBB
$FFB8, $FFB9
$FFB6, $FFB7
$FF80–$FFB5
MSCAN 1 receive
MSCAN 1 transmit
Reserved
Reserved
I bit
I bit
I bit
I bit
Local Enable
PACTL (PAI)
SP0CR1 (SPIE)
SC0CR2
(TIE, TCIE, RIE, ILIE)
SC1CR2
(TIE, TCIE, RIE, ILIE)
ATDxCTL2 (ASCIE)
C0RIER (WUPIE)
KWIEJ[7:0] and
KWIEH[7:0]
MCCTL (MCZI)
PBCTL (PBOVI)
C0RIER (RWRNIE,
TWRNIE,
RERRIE, TERRIE,
BOFFIE, OVRIE)
C0RIER (RXFIE)
C0TCR (TXEIE[2:0])
PLLCR (LOCKIE, LHIE)
IBCR (IBIE)
C1RIER (WUPIE)
C1RIER (RWRNIE,
TWRNIE,
RERRIE, TERRIE,
BOFFIE, OVRIE)
C1RIER (RXFIE)
C1TCR (TXEIE[2:0])
Technical Data
136
HPRIO Value to
Elevate
$DA
$D8
$D6
$D4
$D2
$D0
$CE
$CC
$CA
$C8
$C6
$C4
$C2
$C0
$BE
$BC
$BA
$B8
$B6
$80–$B4
MC68HC912DG128 — Rev 3.0
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Resets and Interrupts
Interrupt Control and Priority Registers
9.5 Interrupt Control and Priority Registers
INTCR — Interrupt Control Register
RESET:
Bit 7
IRQE
0
6
IRQEN
1
$001E
5
DLY
1
4
0
0
3
0
0
2
0
0
1
0
0
Bit 0
0
0
Freescale Semiconductor, Inc...
IRQE — IRQ Select Edge Sensitive Only
0 = IRQ configured for low-level recognition.
1 = IRQ configured to respond only to falling edges (on pin
PE1/IRQ).
IRQE can be read anytime and written once in normal modes. In
special modes, IRQE can be read anytime and written anytime,
except the first write is ignored.
IRQEN — External IRQ Enable
The IRQ pin has an active pull-up. See Table 3-4.
0 = External IRQ pin is disconnected from interrupt logic.
1 = External IRQ pin is connected to interrupt logic.
IRQEN can be read and written anytime in all modes.
DLY — Enable Oscillator Start-up Delay on Exit from STOP
The delay time of about 4096 cycles is based on the X clock rate
chosen.
0 = No stabilization delay imposed on exit from STOP mode. A
stable external oscillator must be supplied.
1 = Stabilization delay is imposed before processing resumes after
STOP.
DLY can be read anytime and written once in normal modes. In
special modes, DLY can be read and written anytime.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
137
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Resets and Interrupts
Bit 7
6
5
4
3
2
1
Bit 0
1
PSEL6
PSEL5
PSEL4
PSEL3
PSEL2
PSEL1
0
1
1
1
1
0
0
1
0
RESET:
HPRIO — Highest Priority I Interrupt
$001F
Write only if I mask in CCR = 1 (interrupts inhibited). Read anytime.
To give a maskable interrupt source highest priority, write the low byte of
the vector address to the HPRIO register. For example, writing $F0 to
HPRIO would assign highest maskable interrupt priority to the real-time
interrupt timer ($FFF0). If an un-implemented vector address or a non-Imasked vector address (value higher than $F2) is written, then IRQ will
be the default highest priority interrupt.
9.6 Interrupt test registers
These registers are used in special modes for testing the interrupt logic
and priority without needing to know which modules and what functions
are used to generate the interrupts.Each bit is used to force a specific
interrupt vector by writing it to 1.Bits are named with B6 through F4 to
indicate vectors $FFB6 through $FFF4. These bits are also used in
special modes to view that an interrupt caused by a module has reached
the interrupt module.
These registers can only be read in special modes (read in normal mode
will return $00). Reading these registers at the same time as the interrupt
is changing will cause an indeterminate value to be read. These
registers can only be written in special mode.
Technical Data
138
MC68HC912DG128 — Rev 3.0
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Resets and Interrupts
Interrupt test registers
ITST0 — Interrupt Test Register 0
RESET:
Bit 7
ITE6
0
6
ITE8
0
$0018
5
ITEA
0
4
ITEC
0
3
ITEE
0
2
ITF0
0
1
ITF2
0
Bit 0
ITF4
0
ITST1 — Interrupt Test Register 1
RESET:
Bit 7
ITD6
0
6
ITD8
0
$0019
5
ITDA
0
4
ITDC
0
3
ITDE
0
2
ITE0
0
1
ITE2
0
Bit 0
ITE4
0
ITST2 — Interrupt Test Register 2
RESET:
Bit 7
ITC6
0
6
ITC8
0
$001A
5
ITCA
0
4
ITCC
0
3
ITCE
0
2
ITD0
0
1
ITD2
0
Bit 0
ITD4
0
ITST3 — Interrupt Test Register 3
RESET:
Bit 7
ITB6
0
6
ITB8
0
$001B
5
ITBA
0
4
ITBC
0
3
ITBE
0
2
ITC0
0
MC68HC912DG128 — Rev 3.0
MOTOROLA
1
ITC2
0
Bit 0
ITC4
0
Technical Data
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
139
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Resets and Interrupts
9.7 Resets
There are four possible sources of reset. Power-on reset (POR), and
external reset on the RESET pin share the normal reset vector. The
computer operating properly (COP) reset and the clock monitor reset
each has a vector. Entry into reset is asynchronous and does not require
a clock but the MCU cannot sequence out of reset without a system
clock.
9.7.1 Power-On Reset
A positive transition on VDD causes a power-on reset (POR). An external
voltage level detector, or other external reset circuits, are the usual
source of reset in a system. The POR circuit only initializes internal
circuitry during cold starts and cannot be used to force a reset as system
voltage drops.
It is important to use an external low voltage reset circuit (for example:
MC34064 or MC33464) to prevent power transitions or corruption of
RAM or EEPROM.
9.7.2 External Reset
The CPU distinguishes between internal and external reset conditions
by sensing whether the reset pin rises to a logic one in less than nine Eclock cycles after an internal device releases reset. When a reset
condition is sensed, the RESET pin is driven low and a clocked reset
sequence controls when the MCU can begin normal processingby an
internal device for about 16 E-clock cycles, then released. In the case of
a clock monitor error, a 4096 cycle oscillator start-up delay is imposed
before the reset recovery sequence starts (reset is driven low throughout
this 4096 cycle delay). The internal reset recovery sequence then drives
reset low for 16 to 17 cycles and releases the drive to allow reset to rise.
Nine E-clock cycles later the reset pin it is sampled. If the pin is still held
low, the CPU assumes that an external reset has occurred. If the pin is
high, it indicates that the reset was initiated internally by either the COP
system or the clock monitor.
Technical Data
140
MC68HC912DG128 — Rev 3.0
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Resets and Interrupts
Resets
To prevent a COP reset from being detected during an external reset,
hold the reset pin low for at least 32 cycles. To prevent a or clock monitor
reset from being detected during an external reset, hold the reset pin low
for at least 4096 + 32 cycles. An external RC power-up delay circuit on
the reset pin is not recommended as circuit charge time can cause the
MCU to misinterpret the type of reset that has occurred.
9.7.3 COP Reset
The MCU includes a computer operating properly (COP) system to help
protect against software failures. When COP is enabled, software must
write $55 and $AA (in this order) to the COPRST register in order to keep
a watchdog timer from timing out. Other instructions may be executed
between these writes. A write of any value other than $55 or $AA or
software failing to execute the sequence properly causes a COP reset to
occur. In addition, windowed COP operation can be selected. In this
mode, a write to the COPRST register must occur in the last 25% of the
selected period. A premature write will also reset the part.
9.7.4 Clock Monitor Reset
If clock frequency falls below a predetermined limit when the clock
monitor is enabled, a reset occurs.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
141
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Resets and Interrupts
9.8 Effects of Reset
When a reset occurs, MCU registers and control bits are changed to
known start-up states, as follows.
9.8.1 Operating Mode and Memory Map
Operating mode and default memory mapping are determined by the
states of the BKGD, MODA, and MODB pins during reset. The SMODN,
MODA, and MODB bits in the MODE register reflect the status of the
mode-select inputs at the rising edge of reset. Operating mode and
default maps can subsequently be changed according to strictly defined
rules.
9.8.2 Clock and Watchdog Control Logic
The COP watchdog system is enabled, with the CR[2:0] bits set for the
longest duration time-out. The clock monitor is disabled. The RTIF flag
is cleared and automatic hardware interrupts are masked. The rate
control bits are cleared, and must be initialized before the RTI system is
used. The DLY control bit is set to specify an oscillator start-up delay
upon recovery from STOP mode.
9.8.3 Interrupts
PSEL is initialized in the HPRIO register with the value $F2, causing the
external IRQ pin to have the highest I-bit interrupt priority. The IRQ pin
is configured for level-sensitive operation (for wired-OR systems).
However, the interrupt mask bits in the CPU12 CCR are set to mask Xand I-related interrupt requests.
9.8.4 Parallel I/O
If the MCU comes out of reset in a single-chip mode, all ports are
configured as general-purpose high-impedance inputs.
Technical Data
142
MC68HC912DG128 — Rev 3.0
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Resets and Interrupts
Effects of Reset
If the MCU comes out of reset in an expanded mode, port A and port B
are used for the address/data bus, and port E pins are normally used to
control the external bus (operation of port E pins can be affected by the
PEAR register). Out of reset, port J, port H, port K, port IB, port P, port
S, port T, port CAN[7:4], port AD0 and port AD1 are all configured as
general-purpose inputs.
9.8.5 Central Processing Unit
After reset, the CPU fetches a vector from the appropriate address, then
begins executing instructions. The stack pointer and other CPU registers
are indeterminate immediately after reset. The CCR X and I interrupt
mask bits are set to mask any interrupt requests. The S bit is also set to
inhibit the STOP instruction.
9.8.6 Memory
After reset, the internal register block is located from $0000 to $03FF,
RAM is at $2000 to $3FFF, and EEPROM is located at $0800 to $0FFF.
In single chip mode, one 32-Kbyte Flash module is located from $4000
to $7FFF and $C000 to $FFFF, and the other three 32-Kbyte Flash
modules are accessible through the program page window located from
$8000 to $BFFF. The first 32-Kbyte FLASH EEPROM is also accessible
through the program page window.
9.8.7 Other Resources
The enhanced capture timer (ECT), pulse width modulation timer
(PWM), serial communications interfaces (SCI0 and SCI1), serial
peripheral interface (SPI), inter-IC bus (IIC), Motorola Scalable CAN
modules (MSCAN0 and MSCAN1) and analog-to-digital converters
(ATD0 and ATD1) are off after reset.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
143
Freescale Semiconductor, Inc.
Resets and Interrupts
9.9 Register Stacking
Once enabled, an interrupt request can be recognized at any time after
the I bit in the CCR is cleared. When an interrupt service request is
recognized, the CPU responds at the completion of the instruction being
executed. Interrupt latency varies according to the number of cycles
required to complete the instruction. Some of the longer instructions can
be interrupted and will resume normally after servicing the interrupt.
Freescale Semiconductor, Inc...
When the CPU begins to service an interrupt, the instruction queue is
cleared, the return address is calculated, and then it and the contents of
the CPU registers are stacked as shown in Table 9-2.
.
Table 9-2. Stacking Order on Entry to Interrupts
Memory Location
SP – 2
CPU Registers
RTNH : RTNL
SP – 4
YH : YL
SP – 6
XH : XL
SP – 8
SP – 9
B:A
CCR
After the CCR is stacked, the I bit (and the X bit, if an XIRQ interrupt
service request is pending) is set to prevent other interrupts from
disrupting the interrupt service routine. The interrupt vector for the
highest priority source that was pending at the beginning of the interrupt
sequence is fetched, and execution continues at the referenced location.
At the end of the interrupt service routine, an RTI instruction restores the
content of all registers from information on the stack, and normal
program execution resumes.
If another interrupt is pending at the end of an interrupt service routine,
the register unstacking and restacking is bypassed and the vector of the
interrupt is fetched.
Technical Data
144
MC68HC912DG128 — Rev 3.0
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Resets and Interrupts
9.10 Important User Information
Freescale Semiconductor, Inc...
Before disabling an interrupt using a local interrupt control bit, set the I
mask bit in the CCR. Failing to do so may cause an SWI interrupt to be
fetched instead of the vector for the interrupt source that was disabled.
Technical Data
145
MC68HC912DG128 — Rev 3.0
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Resets and Interrupts
Technical Data
146
MC68HC912DG128 — Rev 3.0
Resets and Interrupts
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Section 10. I/O Ports with Key Wake-up
10.1 Contents
10.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 147
10.3
Key Wake-up and Port Registers . . . . . . . . . . . . . . . . . . . . . .148
10.4
Key Wake-Up Input Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . . 152
10.2 Introduction
The MC68HC912DG128 offers 16 additional I/O ports with key wake-up
capability.
The key wake-up feature of the MC68HC912DG128 issues an interrupt
that will wake up the CPU when it is in the STOP or WAIT mode. Two
ports are associated with the key wake-up function: port H and port J.
Port H and port J wake-ups are triggered with a rising or falling signal
edge. For each pin which has an interrupt enabled, there is a path to the
interrupt request signal which has no clocked devices when the part is in
stop mode. This allows an active edge to bring the part out of stop.
Digital filtering is included to prevent pulses shorter than a specified
value from waking the part from STOP.
An interrupt is generated when a bit in the KWIFH or KWIFJ register and
its corresponding KWIEH or KWIEJ bit are both set. All 16 bits/pins share
the same interrupt vector. Key wake-ups can be used with the pins
configured as inputs or outputs.
Default register addresses, as established after reset, are indicated in
the following descriptions. For information on re-mapping the register
block, refer to Operating Modes.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
I/O Ports with Key Wake-up
For More Information On This Product,
Go to: www.freescale.com
147
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
I/O Ports with Key Wake-up
10.3 Key Wake-up and Port Registers
PORTJ — Port J Register
$0028
Bit 7
6
5
4
3
2
1
Bit 0
PORT
PJ7
PJ6
PJ5
PJ4
PJ3
PJ2
PJ1
PJ0
KWU
KWJ7
KWJ6
KWJ5
KWJ4
KWJ3
KWJ2
KWJ1
KWJ0
RESET:
-
-
-
-
-
-
-
-
Read and write anytime.
Bit 7
6
5
4
3
2
1
Bit 0
PH7
PH6
PH5
PH4
PH3
PH2
PH1
PH0
KWU
KWH7
KWH6
KWH5
KWH4
KWH3
KWH2
KWH1
KWH0
RESET:
-
-
-
-
-
-
-
-
PORTH — Port H Register
$0029
Read and write anytime.
Bit 7
6
5
4
3
2
1
Bit 0
DDJ7
DDJ6
DDJ5
DDJ4
DDJ3
DDJ2
DDJ1
DDJ0
0
0
0
0
0
0
0
0
RESET:
DDRJ — Port J Data Direction Register
$002A
Data direction register J is associated with port J and designates each
pin as an input or output.
Read and write anytime
DDRJ[7:0] — Data Direction Port J
0 = Associated pin is an input
1 = Associated pin is an output
Technical Data
148
MC68HC912DG128 — Rev 3.0
I/O Ports with Key Wake-up
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
I/O Ports with Key Wake-up
Key Wake-up and Port Registers
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
DDH7
DDH6
DDH5
DDH4
DDH3
DDH2
DDH1
DDH0
0
0
0
0
0
0
0
0
DDRH — Port H Data Direction Register
$002B
Data direction register H is associated with port H and designates each
pin as an input or output. Read and write anytime.
DDRH[7:0] — Data Direction Port H
0 = Associated pin is an input
1 = Associated pin is an output
KWIEJ — Key Wake-up Port J Interrupt Enable Register
RESET:
$002C
Bit 7
6
5
4
3
2
1
Bit 0
KWIEJ7
KWIEJ6
KWIEJ5
KWIEJ4
KWIEJ3
KWIEJ2
KWIEJ1
KWIEJ0
0
0
0
0
0
0
0
0
Read and write anytime.
KWIEJ[7:0] — Key Wake-up Port J Interrupt Enables
0 = Interrupt for the associated bit is disabled
1 = Interrupt for the associated bit is enabled
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
KWIEH7
KWIEH6
KWIEH5
KWIEH4
KWIEH3
KWIEH2
KWIEH1
KWIEH0
0
0
0
0
0
0
0
0
KWIEH — Key Wake-up Port H Interrupt Enable Register
$002D
Read and write anytime.
KWIEH[7:0] — Key Wake-up Port H Interrupt Enables
0 = Interrupt for the associated bit is disabled
1 = Interrupt for the associated bit is enabled
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
I/O Ports with Key Wake-up
For More Information On This Product,
Go to: www.freescale.com
149
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
I/O Ports with Key Wake-up
KWIFJ — Key Wake-up Port J Flag Register
$002E
Bit 7
6
5
4
3
2
1
Bit 0
KWIFJ7
KWIFJ6
KWIFJ5
KWIFJ4
KWIFJ3
KWIFJ2
KWIFJ1
KWIFJ0
0
0
0
0
0
0
0
0
RESET:
Read and write anytime.
Each flag is set by an active edge on its associated input pin. This could
be a rising or falling edge based on the state of the KWPJ register. To
clear the flag, write one to the corresponding bit in KWIFJ.
Initialize this register after initializing KWPJ so that illegal flags can be
cleared.
KWIFJ[7:0] — Key Wake-up Port J Flags
0 = Active edge on the associated bit has not occurred
1 = Active edge on the associated bit has occurred (an interrupt will
occur if the associated enable bit is set).
Bit 7
6
5
4
3
2
1
Bit 0
KWIFH7
KWIFH6
KWIFH5
KWIFH4
KWIFH3
KWIFH2
KWIFH1
KWIFH0
0
0
0
0
0
0
0
0
RESET:
KWIFH — Key Wake-up Port H Flag Register
$002F
Read and write anytime.
Each flag is set by an active edge on its associated input pin. This could
be a rising or falling edge based on the state of the KWPH register. To
clear the flag, write one to the corresponding bit in KWIFH.
Initialize this register after initializing KWPH so that illegal flags can be
cleared.
KWIFH[7:0] — Key Wake-up Port H Flags
0 = Active edge on the associated bit has not occurred
1 = Active edge on the associated bit has occurred (an interrupt will
occur if the associated enable bit is set)
Technical Data
150
MC68HC912DG128 — Rev 3.0
I/O Ports with Key Wake-up
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
I/O Ports with Key Wake-up
Key Wake-up and Port Registers
KWPJ — Key Wake-up Port J Polarity Register
RESET:
$0030
Bit 7
6
5
4
3
2
1
Bit 0
KWPJ7
KWPJ6
KWPJ5
KWPJ4
KWPJ3
KWPJ2
KWPJ1
KWPJ0
0
0
0
0
0
0
0
0
Read and write anytime. It is best to clear the flags after initializing this
register because changing the polarity of a bit can cause the associated
flag to become set.
KWPJ[7:0] — Key Wake-up Port J Polarity Selects
0 = Falling edge on the associated port J pin sets the associated
flag bit in the KWIFJ register and a resistive pull-up device is
connected to associated port J input pin.
1 = Rising edge on the associated port J pin sets the associated
flag bit in the KWIFJ register and a resistive pull-down device
is connected to associated port J input pin.
KWPH — Key Wake-up Port H Polarity Register
$0031
Bit 7
6
5
4
3
2
1
Bit 0
KWPH7
KWPH6
KWPH5
KWPH4
KWPH3
KWPH2
KWPH1
KWPH0
0
0
0
0
0
0
0
0
RESET:
Read and write anytime. It is best to clear the flags after initializing this
register because changing the polarity of a bit can cause the associated
flag to become set.
KWPH[7:0] — Key Wake-up Port H Polarity Selects
0 = Falling edge on the associated port H pin sets the associated
flag bit in the KWIFH register and a resistive pull-up device is
connected to associated port H input pin.
1 = Rising edge on the associated port H pin sets the associated
flag bit in the KWIFH register and a resistive pull-down device
is connected to associated port H input pin.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
I/O Ports with Key Wake-up
For More Information On This Product,
Go to: www.freescale.com
151
Freescale Semiconductor, Inc.
I/O Ports with Key Wake-up
10.4 Key Wake-Up Input Filter
The KWU input signals are filtered by a digital filter which is active only
during STOP mode. The purpose of the filter is to prevent single pulses
shorter than a specified value from waking the part from STOP.
Freescale Semiconductor, Inc...
The filter is composed of an internal oscillator and a majority voting logic.
The filter oscillator starts oscillation by detecting a triggering edge on an
input if the corresponding interrupt enable bit is set. The majority voting
logic takes three samples of an asserted input pin at each filter oscillator
period and if two samples are taken at the triggering level, the filter
recognizes a valid triggering level and sets the corresponding interrupt
flag. In this way, the majority voting logic rejects the short non-triggering
state between two incoming triggering pulses. As the filter is shared with
all KWU inputs, the filter considers any pulse coming from any input pin
for which the corresponding interrupt enable bit is set.
The timing specification is given for a single pulse. The time interval
between the triggering edges of two following pulses should be greater
than the tKWSP in order to be considered as a single pulse by the filter. If
this time interval is shorter than tKWSP, the majority voting logic may treat
the two consecutive pulses as a single valid pulse.
The filter is shared by all the KWU pins. Hence any valid triggering level
on any KWU pin is seen by the filter. The timing specification applies to
the input of the filter.
Technical Data
152
MC68HC912DG128 — Rev 3.0
I/O Ports with Key Wake-up
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
I/O Ports with Key Wake-up
Key Wake-Up Input Filter
Glitch, filtered out, no STOP wake-up
Valid STOP Wake-Up pulse
tKWSTP min.
tKWSTP max.
Minimum time interval between pulses to be recognized as single pulses
tKWSTP
Figure 10-1. STOP Key Wake-up Filter
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
I/O Ports with Key Wake-up
For More Information On This Product,
Go to: www.freescale.com
153
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
I/O Ports with Key Wake-up
Technical Data
154
MC68HC912DG128 — Rev 3.0
I/O Ports with Key Wake-up
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Section 11. Clock Functions
11.1 Contents
11.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 155
11.3
Clock Sources. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 156
11.4
Phase-Locked Loop (PLL) . . . . . . . . . . . . . . . . . . . . . . . . . . . 157
11.5
Acquisition and Tracking Modes. . . . . . . . . . . . . . . . . . . . . . . 159
11.6
Limp-Home and Fast STOP Recovery modes . . . . . . . . . . . . 161
11.7
System Clock Frequency formulas . . . . . . . . . . . . . . . . . . . . . 179
11.8
Clock Divider Chains . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 180
11.9
Computer Operating Properly (COP) . . . . . . . . . . . . . . . . . . .184
11.10 Real-Time Interrupt. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
11.11 Clock Monitor . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 184
11.12 Clock Function Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . 185
11.2 Introduction
Clock generation circuitry generates the internal and external E-clock
signals as well as internal clock signals used by the CPU and on-chip
peripherals. A clock monitor circuit, a computer operating properly
(COP) watchdog circuit, and a periodic interrupt circuit are also
incorporated into the 68HC(9)12DG128.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
155
Freescale Semiconductor, Inc.
Clock Functions
11.3 Clock Sources
A compatible external clock signal can be applied to the EXTAL pin or
the MCU can generate a clock signal using an on-chip oscillator circuit
and an external crystal or ceramic resonator. The MCU uses several
types of internal clock signals derived from the primary clock signal:
TxCLK clocks are used by the CPU.
Freescale Semiconductor, Inc...
ECLK and PCLK are used by the bus interfaces, SPI, PWM, ATD0 and
ATD1.
MCLK is either PCLK or XCLK, and drives on-chip modules such as
SCI0, SCI1 and ECT.
XCLK drives on-chip modules such as RTI, COP and restart-from-stop
delay time.
SLWCLK is used as a calibration output signal.
The MSCAN module is clocked by EXTALi or SYSCLK, under control of
an MSCAN bit.
The clock monitor is clocked by EXTALi.
The BDM system is clocked by BCLK or ECLK, under control of a BDM
bit.
A slow mode clock divider is included to deliver a lower clock frequency
for the SCI baud rate generators, the ECT timer module, and the RTI and
COP clocks. The slow clock bus frequencies divide the crystal frequency
in a programmable range of 4 to 252, with steps of 4.
Figure 11-1 shows some of the timing relationships. See the Clock
Divider Chains section for further details.
Technical Data
156
MC68HC912DG128 — Rev 3.0
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Clock Functions
Phase-Locked Loop (PLL)
T1CLK
T2CLK
T3CLK
T4CLK
INT ECLK
PCLK
XCLK
CANCLK
Figure 11-1. Internal Clock Relationships
11.4 Phase-Locked Loop (PLL)
The phase-locked loop (PLL) of the 68HC(9)12DG128 is designed for
robust operation in an Automotive environment. The allowed PLL crystal
or ceramic resonator reference of 0.5 to 8MHz is selected for the wide
availability of components with good stability over the automotive
temperature range. Please refer to Figure 11-6 in section Clock Divider
Chains for an overview of system clocks.
NOTE:
When selecting a crystal, it is recommended to use one with the lowest
possible frequency in order to minimise EMC emissions.
An oscillator design with reduced power consumption allows for slow
wait operation with a typical power supply current less than a milliampere. The PLL circuitry can be bypassed when the VDDPLL supply is
at VSS level. In this case, the PLL module is powered down and the
oscillator output transistor has a stronger transconductance for improved
drive of higher frequency resonators (as the crystal frequency needs to
be twice the maximum bus frequency). Refer to Figure 3-3 in Pinout and
Signal Descriptions.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
157
Freescale Semiconductor, Inc.
Clock Functions
EXTAL
REDUCED
CONSUMPTION
OSCILLATOR
REFERENCE
PROGRAMMABLE
DIVIDER
LOCK
LOCK
DETECTOR
REFDV <2:0>
REFCLK
XTAL
DIVCLK
EXTALi
PDET
PHASE
DETECTOR
UP
DOWN
CPUMP
VCO
VDDPLL
Freescale Semiconductor, Inc...
SLOW MODE
PROGRAMMABLE
CLOCK DIVIDER
SLWCLK
LOOP
PROGRAMMABLE
DIVIDER
LOOP
FILTER
÷2
SLDV <5:0>
EXTALi
SYN <5:0>
XCLK
XFC
PAD
×2
PLLCLK
Figure 11-2. PLL Functional Diagram
The PLL may be used to run the MCU from a different time base than the
incoming crystal value. It creates an integer multiple of a reference
frequency. For increased flexibility, the crystal clock can be divided by
values in a range of 1 – 8 (in unit steps) to generate the reference
frequency. The PLL can multiply this reference clock in a range of 1 to
64. Although it is possible to set the divider to command a very high clock
frequency, do not exceed the specified bus frequency limit for the MCU.
If the PLL is selected, it will continue to run when in WAIT mode resulting
in more power consumption than normal. To take full advantage of the
reduced power consumption of WAIT mode, turn off the PLL before
going into WAIT. Please note that in this case the PLL stabilization time
applies.
The PLL operation is suspended in STOP mode. After STOP exit
followed by the stabilization time, it resumes operation at the same
frequency, provided the AUTO bit is set.
A passive external loop filter must be placed on the control line (XFC
pad). The filter is a second-order, low-pass filter to eliminate the VCO
input ripple. Values of components in the diagram are dependent upon
the desired VCO operation. See XFC description.
Technical Data
158
MC68HC912DG128 — Rev 3.0
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Clock Functions
Acquisition and Tracking Modes
11.5 Acquisition and Tracking Modes
The lock detector compares the frequencies of the VCO feedback clock,
DIVCLK, and the final reference clock, REFCLK. Therefore, the speed
of the lock detector is directly proportional to the final reference
frequency. The circuit determines the mode of the PLL and the lock
condition based on this comparison.
Freescale Semiconductor, Inc...
The PLL filter is manually or automatically configurable into one of two
operating modes:
•
Acquisition mode — In acquisition mode, the filter can make large
frequency corrections to the VCO. This mode is used at PLL startup or when the PLL has suffered a severe noise hit and the VCO
frequency is far off the desired frequency. This mode can also be
desired in harsh environments when the leakage levels on the
filter pin (XFC) can overcome the tracking currents of the PLL
charge pump. When in acquisition mode, the ACQ bit in the PLL
control register is clear.
•
Tracking mode — In tracking mode, the filter makes only small
corrections to the frequency of the VCO. The PLL enters tracking
mode when the VCO frequency is nearly correct. The PLL is
automatically in tracking mode when not in acquisition mode or
when the ACQ bit is set.
The PLL can change the bandwidth or operational mode of the loop filter
manually or automatically. With an identical filtering time constant, the
PLL bandwidth is larger in acquisition mode than in tracking by a ratio of
about 3.
In automatic bandwidth control mode (AUTO = 1), the lock detector
automatically switches between acquisition and tracking modes.
Automatic bandwidth control mode also is used to determine when the
VCO clock, PLLCLK, is safe to use as the source for the base clock,
SYSCLK. If PLL LOCK interrupt requests are enabled, the software can
wait for an interrupt request and then check the LOCK bit. If CPU
interrupts are disabled, software can poll the LOCK bit continuously
(during PLL start-up, usually) or at periodic intervals. In either case,
when the LOCK bit is set, the PLLCLK clock is safe to use as the source
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
159
Freescale Semiconductor, Inc.
Clock Functions
for the base clock. See Clock Divider Chains. If the VCO is selected as
the source for the base clock and the LOCK bit is clear, the PLL has
suffered a severe noise hit and the software must take appropriate
action, depending on the application.
Freescale Semiconductor, Inc...
The following conditions apply when the PLL is in automatic bandwidth
control mode:
•
The ACQ bit is a read-only indicator of the mode of the filter.
•
The ACQ bit is set when the VCO frequency is within a certain
tolerance, ∆trk, and is cleared when the VCO frequency is out of a
certain tolerance, ∆unt. See 19 Electrical Characteristics.
•
The LOCK bit is a read-only indicator of the locked state of the PLL.
•
The LOCK bit is set when the VCO frequency is within a certain
tolerance, ∆Lock, and is cleared when the VCO frequency is out of
a certain tolerance, ∆unl. See 19 Electrical Characteristics.
•
CPU interrupts can occur if enabled (LOCKIE = 1) when the lock
condition changes, toggling the LOCK bit.
The PLL also can operate in manual mode (AUTO = 0). All LOCK
features described above are active in this mode, only the bandwidth
control is disabled. Manual mode is used mainly for systems operating
under harsh conditions (e.g.uncoated PCBs in automotive
environments). When this is the case, the PLL is likely to remain in
acquisition mode. The following conditions apply when in manual mode:
•
ACQ is a writable control bit that controls the mode of the filter.
Before turning on the PLL in manual mode, the ACQ bit must be
clear.
•
In case tracking is desired (ACQ = 1), the software must wait a
given time, tacq, after turning on the PLL by setting PLLON in the
PLL control register. This is to avoid switching to tracking mode
too early while the XFC voltage level is still too far away from its
quiescent value corresponding to the target frequency. This
operation would be very detrimental to the stabilization time.
Technical Data
160
MC68HC912DG128 — Rev 3.0
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Clock Functions
Limp-Home and Fast STOP Recovery modes
11.6 Limp-Home and Fast STOP Recovery modes
If the crystal frequency is not available due to a crystal failure or a long
crystal start-up time, the MCU system clock can be supplied by the VCO
at its minimum operating frequency, f VCOMIN. This mode of operation is
called Limp-Home Mode and is only available when the VDDPLL supply
voltage is at VDD level (i.e. power supply for the PLL module is present).
Upon power-up, the ability of the system to start in Limp-Home Mode is
restricted to normal MCU modes only.
The Clock Monitor circuit (see section Clock Monitor) can detect the loss
of EXTALi, the external clock input signal, regardless of whether this
signal is used as the source for MCU clocks or as the PLL reference
clock. The clock monitor control bits, CME and FCME, are used to
enable or disable external clock detection.
A missing external clock may occur in the three following instances:
•
During normal clock operation.
•
At Power-On Reset.
•
In the STOP exit sequence
11.6.1 Clock Loss during Normal Operation
The ‘no limp-home mode’ bit, NOLHM, determines how the MCU
responds to an external clock loss in this case.
With limp home mode disabled (NOLHM bit set) and the clock monitor
enabled (CME or FCME bits set), on a loss of clock the MCU is reset via
the clock monitor reset vector. A latch in the PLL control section prevents
the chip exiting reset in Limp Home Mode (this is required as the NOLHM
bit gets cleared by reset). Only external clock activity can bring the MCU
out from this reset state. Once reset has been exited, the latch is cleared
and another session, with or without Limp Home Mode enabled, can
take place. This is the same behavior as standard M68HC12 circuits
without PLL or operation with VDDPLL at VSS level.
With limp home mode enabled (NOLHM bit cleared) and the clock
monitor enabled (CME or FCME bits set), on a loss of clock, the PLL
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
161
Freescale Semiconductor, Inc.
Clock Functions
VCO clock at its minimum frequency, f VCOMIN, is provided as the system
clock, allowing the MCU to continue operating.
Freescale Semiconductor, Inc...
The MCU is said to be operating in “limp-home” mode with the forced
VCO clock as the system clock. PLLON and BCSP (‘bus clock select
PLL’) signals are forced high and the MCS (‘module clock select’) signal
is forced low. The LHOME flag in the PLLFLG register is set to indicate
that the MCU is running in limp-home mode. A change of this flag sets
the limp-home interrupt flag, LHIF, and if enabled by the LHIE bit, the
limp-home mode interrupt is requested. The Clock Monitor is enabled
irrespective of CME and FCME bit settings. Module clocks to the RTI &
COP (XCLK), BDM (BCLK) and ECT & SCI (MCLK) are forced to be
PCLK (at f VCOMIN) and ECLK is also equal to f VCOMIN. MSCAN clock
select is unaffected.
EXTALi
A
B
Clock Monitor Fail
0 --> 4096
0 --> 4096
13-stage counter
(Clocked by XCLK)
Limp-Home
BCSP
SYSCLK
Restore BCSP
PLLCLK (Limp-Home)
Restore PLLCLK or EXTALi
Figure 11-3. Clock Loss during Normal Operation
The clock monitor is polled each time the 13-stage free running counter
reaches a count of 4096 XCLK cycles i.e. mid-count, hence the clock
status gets checked once every 8192 XCLK cycles. When the presence
of an external clock is detected, the MCU exits limp-home mode,
clearing the LHOME flag and setting the limp-home interrupt flag. Upon
leaving limp-home mode, BCSP and MCS signals are restored to their
Technical Data
162
MC68HC912DG128 — Rev 3.0
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Clock Functions
Limp-Home and Fast STOP Recovery modes
values before the clock loss. All clocks return to their normal settings and
Clock Monitor control is returned to the CME & FCME bits. If AUTO and
BCSP bits were set before the clock loss (selecting the PLL to provide a
system clock) the SYSCLK ramps-up and the PLL locks at the previously
selected frequency. To prevent PLL operation when the external clock
frequency comes back, software should clear the BCSP bit while running
in limp-home mode.
The two shaded regions A and B in Figure 11-3 present a of code run
away due to incorrect clocks on SYSCLK if the MCU is clocked by
EXTALi and the PLL is not used.
In region A, there is a delay between the loss of clock and its detection
by the clock monitor. When the EXTALi clock signal is disturbed, the
clock generation circuitry may receive an out of spec signal and drive the
CPU with irregular clocks. This may lead to code runaway.
In region B, as the 13-stage counter is free running, the count of 4096
may be reached when the amplitude of the EXTALi clock has not
stabilized. In this case, an improper EXTALi is sent to the clock
generation circuitry when limp-home mode is exited. This may also
cause code runaway.
If the MCU is clocked by the PLL, the risk of code runaway is very
low, but it can still occur under certain conditions due to irregular
clocks from the clock source appearing on the SYSCLK.
CAUTION:
NOTE:
The COP watch dog should always be enabled in order to reset the MCU
in case of a code runaway situation.
It is always advisable to take additional precautions within the
application software to trap such situations.
11.6.2 No Clock at Power-On Reset
The voltage level on VDDPLL determines how the MCU responds to an
external clock loss in this case.
With the VDDPLL supply voltage at VDD level, any reset sets the Clock
Monitor Enable bit (CME) and the PLLON bit and clears the NOLHM bit.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
163
Freescale Semiconductor, Inc.
Clock Functions
Therefore, if the MCU is powered up without an external clock, limphome mode is entered provided the MCU is in a normal mode of
operation.
VDD
Freescale Semiconductor, Inc...
Power-On Detector
EXTALi
(Slow EXTALi)
Clock Monitor Fail
Limp-Home
13-stage counter
(Clocked by XCLK)
0 --> 4096
0 --> 4096
BCSP
Reset: BCSP = 0
Internal reset
SYSCLK
SYSCLK
(Slow EXTALi)
PLLCLK (L.H.)
EXTALi
PLLCLK (Software check of Limp-Home Flag)
EXTALi
Figure 11-4. No Clock at Power-On Reset
Technical Data
164
MC68HC912DG128 — Rev 3.0
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Clock Functions
Limp-Home and Fast STOP Recovery modes
During this power up sequence, after the POR pulse falling edge, the
VCO supplies the limp-home clock frequency to the 13-stage counter, as
the BCSP output is forced high and MCS is forced low. XCLK, BCLK and
MCLK are forced to be PCLK, which is supplied by the VCO at fVCOMIN.
The initial period taken for the 13-stage counter to reach 4096 defines
the internal reset period.
If the clock monitor indicates the presence of an external clock during the
internal reset period, limp-home mode is de-asserted and the 13-stage
counter is then driven by EXTALi clock. After the 13-stage counter
reaches a count of 4096 XCLK cycles, the internal reset is released, the
13-stage counter is reset and the MCU exits reset normally using
EXTALi clock.
However, if the crystal start-up time is longer than the initial count of
4096 XCLK cycles, or in the absence of an external clock, the MCU will
leave the reset state in limp-home mode. The LHOME flag is set and
LHIF limp-home interrupt request is set, to indicate it is not operating at
the desired frequency. Then after yet another 4096 XCLK cycles
followed regularly by 8192 XCLK cycles (corresponding to the 13-stage
counter timing out), a check of the clock monitor status is performed.
When the presence of an external clock is detected limp-home mode is
exited generating a limp-home interrupt if enabled.
CAUTION:
The clock monitor circuit can be misled by the EXTALi clock into
reporting a good signal before it has fully stabilised. Under these
conditions improper EXTALi clock cycles can occur on SYSCLK. This
may lead to a code runaway. To ensure that this situation does not
occur, the external Reset period should be longer than the oscillator
stabilisation time - this is an application dependent parameter.
With the VDDPLL supply voltage at VSS level, the PLL module and
hence limp-home mode are disabled, the device will remain effectively
in a static state whilst there is no activity on EXTALi. The internal reset
period and MCU operation will execute only on EXTALi clock.
NOTE:
The external clock signal must stabilise within the initial 4096 reset
counter cycles.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
165
Freescale Semiconductor, Inc.
Clock Functions
11.6.3 STOP Exit and Fast STOP Recovery
Stop mode is entered when a STOP instruction is executed. Recovery
from STOP depends primarily on the state of the three status bits
NOLHM, CME & DLY.
Freescale Semiconductor, Inc...
The DLY bit controls the duration of the waiting period between the
actual exit for some key blocks (e.g. clock monitor, clock generators) and
the effective exit from stop for all the rest of the MCU. DLY=1 enables
the 13-stage counter to generate a 4096 count delay. DLY=0 selects no
delay. As the XCLK is derived from the slow mode divider, the value in
the SLOW register modifies the actual delay time.
NOTE:
DLY=0 is only recommended when there is a good signal available
at the EXTAL pin (e.g. an external square wave source).
STOP mode is exited with an external reset, an external interrupt from
IRQ or XIRQ, a Key Wake-Up interrupt from port J or port H, or an
MSCAN Wake-Up interrupt.
Technical Data
166
MC68HC912DG128 — Rev 3.0
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Clock Functions
Limp-Home and Fast STOP Recovery modes
EXTALi
Clock Monitor Fail
Limp-Home
0 --> 4096
13-stage counter
(Clocked by XCLK)
BCSP
Restore BCSP
STOP (DLY = 1)
STOP (DLY = 0)
SYSCLK
PLLCLK (L.H.)
Restore PLLCLK or EXTALi
Figure 11-5. STOP Exit and Fast STOP Recovery
11.6.4 STOP exit without Limp Home mode, clock monitor disabled
(NOLHM=1, CME=0, DLY=X)
If Limp home mode is disabled (VDDPLL=VSS or NOLHM bit set) and the
CME (or FCME) bit is cleared, the MCU goes into STOP mode when a
STOP instruction is executed.
If EXTALi clock is present then exit from STOP will occur normally using
this clock. Under this condition, DLY should always be set to allow the
crystal to stabilise and minimise the risk of code runaway. With DLY=1
execution resumes after a delay of 4096 XCLK cycles.
NOTE:
The external clock signal should stabilise within the 4096 reset counter
cycles. Use of DLY=0 is not recommended due to this requirement.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
167
Freescale Semiconductor, Inc.
Clock Functions
11.6.5 Executing the STOP instruction without Limp Home mode, clock monitor enabled
(NOLHM=1, CME=1, DLY=X)
If the NOLHM bit and the CME (or FCME) bits are set, a clock monitor
failure is detected when a STOP instruction is executed and the MCU
resets via the clock monitor reset vector.
Freescale Semiconductor, Inc...
11.6.6 STOP exit in Limp Home mode with Delay
(NOLHM=0, CME=X, DLY=1)
If the NOLHM bit is cleared, then the CME (or FCME) bit is masked when
a STOP instruction is executed to prevent a clock monitor failure. When
coming out of STOP mode, the MCU goes into limp-home mode where
CME and FCME signals are asserted.
When using a crystal oscillator, a normal STOP exit sequence requires
the DLY bit to be set to allow for the crystal stabilization period.
With the 13-stage counter clocked by the VCO (at fVCOMIN), following a
delay of 4096 XCLK cycles at the limp-home frequency, if the clock
monitor indicates the presence of an external clock, the limp-home mode
is de-asserted and the MCU exits STOP normally using EXTALi clock.
Where the crystal start-up time is longer than the initial count of 4096
XCLK cycles, or in the absence of an external clock, the MCU recovers
from STOP following the 4096 count in limp-home mode with both the
LHOME flag set and the LHIF limp-home interrupt request set to indicate
it is not operating at the desired frequency. Each time the 13-stage
counter reaches a count of 4096 XCLK cycles, a check of the clock
monitor status is performed.
When the presence of an external clock is detected, limp-home mode is
exited and the LHOME flag is cleared. This sets the limp-home interrupt
flag and if enabled by the LHIE bit, the limp-home mode interrupt is
requested.
CAUTION:
The clock monitor circuit can be misled by EXTALi clock into reporting a
good signal before it has fully stabilised. Under these conditions,
Technical Data
168
MC68HC912DG128 — Rev 3.0
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Clock Functions
Limp-Home and Fast STOP Recovery modes
improper EXTALi clock cycles can occur on SYSCLK. This may lead to
a code runaway.
11.6.7 STOP exit in Limp Home mode without Delay (Fast Stop Recovery)
(NOLHM=0, CME=X, DLY=0)
Fast STOP recovery refers to any exit from STOP using DLY=0.
If the NOLHM bit is cleared, then the CME (or FCME) bit is masked when
a STOP instruction is executed to prevent a clock monitor failure. When
coming out of STOP mode, the MCU goes into limp-home mode where
CME and FCME signals are asserted.
When using a crystal oscillator, it is possible to exit STOP with the DLY
bit cleared. In this case, STOP is de-asserted without delay and the MCU
will execute software in limp-home mode, giving the crystal oscillator
time to stablise.
CAUTION:
This mode is not recommended since the risk of the clock monitor
detecting incorrect clocks is high.
Each time the 13-stage counter reaches a count of 4096 XCLK cycles
(every 8192 cycles), a check of the clock monitor status is performed. If
the clock monitor indicates the presence of an external clock limp-home
mode is de-asserted, the LHOME flag is cleared and the limp-home
interrupt flag is set. Upon leaving limp-home mode, BCSP and MCS are
restored to their values before the loss of clock, and all clocks return to
their previous frequencies. If AUTO and BCSP were set before the clock
loss, the SYSCLK ramps-up and the PLL locks at the previously selected
frequency.
To prevent PLL operation when the external clock frequency comes
back, the software should clear the BCSP bit while running in limp-home
mode.
When using an external clock, i.e. a square wave source, it is possible
to exit STOP with the DLY bit cleared. In this case the LHOME flag is
never set and STOP is de-asserted without delay.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
169
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Clock Functions
11.6.8 Pseudo-STOP
Pseudo-STOP is a low power mode similar to STOP where the external
oscillator is allowed to run (at reduced amplitude) whilst the rest of the
part is in STOP. This increases the current consumption over STOP
mode by the amount of current in the oscillator, but reduces wear and
mechanical stress on the crystal.
If the PSTP bit in the PLLCR register is set, the MCU goes into PseudoSTOP mode when a STOP instruction is executed.
Pseudo-STOP mode is exited the same as STOP with an external reset,
an external interrupt from IRQ or XIRQ, a Key Wake-Up interrupt from
port J or port H, or an MSCAN Wake-Up interrupt.
The effect of the DLY bit is the same as noted above in STOP Exit and
Fast STOP Recovery.
11.6.9 Pseudo-STOP exit in Limp Home mode with Delay
(NOLHM=0, CME=X, DLY=1)
When coming out of Pseudo-STOP mode with the NOLHM bit cleared
and the DLY bit set, the MCU goes into limp-home mode (regardless of
the state of the CME or FCME bits).
The VCO supplies the limp-home clock frequency to the 13-stage
counter (XCLK). The BCSP output is forced high and MCS is forced low.
After the 13-stage counter reaches a count of 4096 XCLK cycles, a
check of the clock monitor is performed and as the crystal oscillator was
kept running due to the Pseudo-stop mode, the MCU exits STOP
normally, using the EXTALi clock. In the case where a crystal failure
occurred during pseudo-stop, then the MCU exits STOP using the limp
home clock (fVCOMIN) with both the LHOME flag set and the LHIF limphome interrupt request set to indicate it is not operating at the desired
frequency. Each time the 13-stage counter reaches a count of 4096
XCLK cycles, a check of the clock monitor is performed. If the clock
monitor indicates the presence of an external clock, limp-home mode is
de-asserted, the LHOME flag is cleared and the LHIF limp-home
Technical Data
170
MC68HC912DG128 — Rev 3.0
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Clock Functions
Limp-Home and Fast STOP Recovery modes
interrupt request is set to indicate a return to normal operation using
EXTALi clock.
11.6.10 Pseudo-STOP exit in Limp Home mode without Delay (Fast Stop Recovery)
(NOLHM=0, CME=X, DLY=0)
If Pseudo-STOP is exited with the NOLHM bit set to 0 and the DLY bit is
cleared then the exit from Pseudo-STOP is accomplished without delay
as in Fast STOP recovery.
CAUTION:
Where Pseudo-STOP recovers using the Limp Home Clock the VCO which has been held in STOP - must be restarted in order to supply the
limp home frequency. This restart, which occurs at a high frequency and
ramps toward the limp home frequency, is almost immediately supplied
to the CPU before it may have reached the steady state frequency. It is
possible that the initial clock frequency may be high enough to cause the
CPU to function incorrectly with a resultant risk of code runaway.
11.6.11 Pseudo-STOP exit without Limp Home mode, clock monitor enabled
(NOLHM=1, CME=1, DLY=X)
If the NOLHM bit is set and the CME (or FCME) bits are set, a clock
monitor failure is detected when a STOP instruction is executed and the
MCU resets via the clock monitor reset vector.
11.6.12 Pseudo-STOP exit without Limp Home mode, clock monitor disabled
(NOLHM=1, CME=0, DLY=1)
If NOLHM is set to 1 and the CME and FCME bits are cleared, the limp
home clock is not used. In this mode, crystal activity is the only method
by which the device may recover from Pseudo-STOP. The device will
start execution with the EXTALi clock following 4096 XCLK cycles.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
171
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Clock Functions
(NOLHM=1, CME=0, DLY=0)
If NOLHM is set to 1 and the CME and FCME bits are cleared, the limp
home clock is not used. In this mode, crystal activity is the only method
by which the device may recover from Pseudo-STOP. The device will
start execution with the EXTALi clock following 16 XCLK cycles.
CAUTION:
Due to switching of the clock this configuration is not recommended.
11.6.13 Summary of STOP and pseudo-STOP Mode Exit Conditions
Table 11-1 and Table 11-2 summarise the exit conditions from STOP
and pseudo-STOP modes using Interrupt, Key-interrupt and XIRQ.
A short RESET pulse should not be used to exit stop or pseudo-STOP
mode because Limp Home mode is automatically entered after RESET
(when VDDPLL=VDD). The RESET wakeup pulse must be longer than the
oscillator startup time (as in power on reset) in order to remove the risk
of code runaway.
. .
Table 11-1. Summary of STOP Mode Exit Conditions
Mode
Conditions
Summary
STOP exit without Limp Home
mode,
clock monitor disabled
NOLHM=1
CME=0
DLY=X
Oscillator must be stable within 4096 XCLK cycles. XCLK
can be modified by SLOW divider register.
Use of DLY=0 only recommended with external clock.
Executing the STOP instruction
without Limp Home mode,
clock monitor enabled
NOLHM=1
CME=1
DLY=X
When a STOP instruction is executed the MCU resets via
the clock monitor reset vector.
STOP exit in Limp Home mode
with Delay
NOLHM=0
CME=X
DLY=1
Oscillator must be stable within 4096
fVCOMIN cycles or there is a possibility of code runaway as
the clock monitor circuit can be misled by EXTALi clock
into reporting a good signal before it has fully stabilised
STOP exit in Limp Home mode
without Delay (Fast Stop
Recovery)
NOLHM=0
CME=X
DLY=0
This mode is only recommended for use with an external
clock source.
Technical Data
172
MC68HC912DG128 — Rev 3.0
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Clock Functions
Limp-Home and Fast STOP Recovery modes
Table 11-2. Summary of Pseudo STOP Mode Exit Conditions
Mode
Conditions
Summary
Pseudo-STOP exit in Limp Home
mode with Delay
NOLHM=0
CME=X
DLY=1
CPU exits stop in limp home mode and oscillator running. If
the oscillator fails during pseudo-STOP and then recovers
there is a possibility of code runaway as the clock monitor
circuit can be misled by EXTALi clock into reporting a
good signal before it has fully stabilised
Pseudo-STOP exit
in Limp Home mode without
Delay (Fast Stop Recovery)
NOLHM=0
CME=X
DLY=0
This mode is not recommended as it is possible that the
initial VCO clock frequency may be high enough to cause
code runaway.
Pseudo-STOP exit without Limp
Home mode, clock monitor
enabled
NOLHM=1
CME=1
DLY=X
When a STOP instruction is executed the MCU resets via
the clock monitor reset vector.
Pseudo-STOP exit without Limp
Home mode, clock monitor
disabled, with Delay
NOLHM=1
CME=0
DLY=1
Oscillator starts operation following 4096 XCLK cycles
(actual controlled by SLOW mode divider).
Pseudo-STOP exit without Limp
Home mode, clock monitor
disabled, without Delay
NOLHM=1
CME=0
DLY=0
This mode is only recommended for use with an external
clock source.
11.6.14 PLL Register Descriptions
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
0
0
SYN5
SYN4
SYN3
SYN2
SYN1
SYN0
0
0
0
0
0
0
0
0
SYNR — Synthesizer Register
$0038
Read anytime, write anytime, except when BCSP = 1 (PLL selected as
bus clock).
If the PLL is on, the count in the loop divider (SYNR) register effectively
multiplies up the bus frequency from the PLL reference frequency by
SYNR + 1. Internally, SYSCLK runs at twice the bus frequency. Caution
should be used not to exceed the maximum rated operating frequency
for the CPU.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
173
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Clock Functions
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
REFDV2
REFDV1
REFDV0
0
0
0
0
0
0
0
0
RESET:
REFDV — Reference Divider Register
$0039
Read anytime, write anytime, except when BCSP = 1.
The reference divider bits provides a finer granularity for the PLL
multiplier steps. The reference frequency is divided by REFDV + 1.
Bit 7
6
5
4
3
2
1
Bit 0
TSTOUT7
TSTOUT6
TSTOUT5
TSTOUT4
TSTOUT3
TSTOUT2
TSTOUT1
TSTOUT0
0
0
0
0
0
0
0
0
RESET:
CGTFLG — Clock Generator Test Register
$003A
Always reads zero, except in test modes.
Bit 7
6
5
4
3
2
1
Bit 0
LOCKIF
LOCK
0
0
0
0
LHIF
LHOME
0
0
0
0
0
0
0
0
RESET:
PLLFLG — PLL Flags
$003B
Read anytime, refer to each bit for write conditions.
LOCKIF — PLL Lock Interrupt Flag
0 = No change in LOCK bit.
1 = LOCK condition has changed, either from a locked state to an
unlocked state or vice versa.
To clear the flag, write one to this bit in PLLFLG. Cleared in limp-home
mode.
Technical Data
174
MC68HC912DG128 — Rev 3.0
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Clock Functions
Limp-Home and Fast STOP Recovery modes
LOCK — Locked Phase Lock Loop Circuit
Regardless of the bandwidth control mode (automatic or manual):
0 = PLL VCO is not within the desired tolerance of the target
frequency.
1 = After the phase lock loop circuit is turned on, indicates the PLL
VCO is within the desired tolerance of the target frequency.
Write has no effect on LOCK bit. This bit is cleared in limp-home mode as
the lock detector cannot operate without the reference frequency.
LHIF — Limp-Home Interrupt Flag
0 = No change in LHOME bit.
1 = LHOME condition has changed, either entered or exited limphome mode.
To clear the flag, write one to this bit in PLLFLG.
LHOME — Limp-Home Mode Status
0 = MCU is operating normally, with EXTALi clock available for
generating clocks or as PLL reference.
1 = Loss of reference clock. CGM delivers PLL VCO limp-home
frequency to the MCU.
For Limp-Home mode, see Limp-Home and Fast STOP Recovery modes.
Bit 7
6
5
4
3
2
1
Bit 0
LOCKIE
PLLON
AUTO
ACQ
0
PSTP
LHIE
NOLHM
0
—(1)
1
0
0
0
0
—(2)
RESET:
PLLCR — PLL Control Register
$003C
1. Set when VDDPLL power supply is high. Forced to 0 when VDDPLL is low.
2. Cleared when VDDPLL power supply is high. Forced to 1 when VDDPLL is low.
Read and write anytime. Exceptions are listed below for each bit.
LOCKIE — PLL LOCK Interrupt Enable
0 = PLL LOCK interrupt is disabled
1 = PLL LOCK interrupt is enabled
Forced to 0 when VDDPLL=0.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
175
Freescale Semiconductor, Inc.
Clock Functions
PLLON — Phase Lock Loop On
0 = Turns the PLL off.
1 = Turns on the phase lock loop circuit. If AUTO is set, the PLL will
lock automatically.
Cannot be cleared when BCSP = 1 (PLL selected as bus clock).
Forced to 0 when VDDPLL is at VSS level. In limp-home mode, the
output of PLLON is forced to 1, but the PLLON bit reads the latched
value.
Freescale Semiconductor, Inc...
AUTO — Automatic Bandwidth Control
0 = Automatic Mode Control is disabled and the PLL is under
software control, using ACQ bit.
1 = Automatic Mode Control is enabled. ACQ bit is read only.
Automatic bandwidth control selects either the high bandwidth
(acquisition) mode or the low bandwidth (tracking) mode depending
on how close to the desired frequency the VCO is running. See
Electrical Specifications.
ACQ — Not in Acquisition
If AUTO = 1 (ACQ is Read Only)
0 = PLL VCO is not within the desired tolerance of the target
frequency. The loop filter is in high bandwidth, acquisition
mode.
1 = After the phase lock loop circuit is turned on, indicates the PLL
VCO is within the desired tolerance of the target frequency.
The loop filter is in low bandwidth, tracking mode.
If AUTO = 0
0 = High bandwidth PLL loop selected
1 = Low bandwidth PLL loop selected
PSTP — Pseudo-STOP Enable
0 = Pseudo-STOP oscillator mode is disabled
1 = Pseudo-STOP oscillator mode is enabled
In Pseudo-STOP mode, the oscillator is still running while the MCU is
maintained in STOP mode. This allows for a faster STOP recovery
and reduces the mechanical stress and aging of the resonator in case
frequent STOP conditions at the expense of a slightly increased
power consumption.
Technical Data
176
MC68HC912DG128 — Rev 3.0
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Clock Functions
Limp-Home and Fast STOP Recovery modes
LHIE — Limp-Home Interrupt Enable
0 = Limp-Home interrupt is disabled
1 = Limp-Home interrupt is enabled
Forced to 0 when VDDPLL is at VSS level.
NOLHM —No Limp-Home Mode
0 = Loss of reference clock forces the MCU in limp-home mode.
1 = Loss of reference clock causes standard Clock Monitor reset.
Read anytime; Normal modes: write once; Special modes: write
anytime. Forced to 1 when VDDPLL is at VSS level.
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
0
BCSP
BCSS
0
0
MCS
0
0
0
0
0
0
0
0
0
0
CLKSEL — Clock Generator Clock select Register
$003D
Read and write anytime. Exceptions are listed below for each bit.
BCSP and BCSS bits determine the clock used by the main system
including the CPU and buses.
BCSP — Bus Clock Select PLL
0 = SYSCLK is derived from the crystal clock or from SLWCLK.
1 = SYSCLK source is the PLL.
Cannot be set when PLLON = 0. In limp-home mode, the output of
BCSP is forced to 1, but the BCSP bit reads the latched value.
BCSS — Bus Clock Select Slow
0 = SYSCLK is derived from the crystal clock EXTALi.
1 = SYSCLK source is the Slow clock SLWCLK.
This bit has no effect when BCSP is set.
MCS — Module Clock Select
0 = M clock is the same as PCLK.
1 = M clock is derived from Slow clock SLWCLK.
This bit determines the clock used by the ECT module and the baud
rate generators of the SCIs. In limp-home mode, the output of MCS is
forced to 0, but the MCS bit reads the latched value.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
177
Freescale Semiconductor, Inc.
Clock Functions
Bit 7
6
5
4
3
2
1
Bit 0
0
0
SLDV5
SLDV4
SLDV3
SLDV2
SLDV1
SLDV0
0
0
0
0
0
0
0
0
RESET:
SLOW — Slow mode Divider Register
$003E
Read and write anytime.
Freescale Semiconductor, Inc...
A write to this register changes the SLWCLK frequency with minimum
delay (less than one SLWCLK cycle), thus allowing immediate tuneup of the performance versus power consumption for the modules
using this clock. The frequency divide ratio is 2 times (SLOW), hence
the divide range is 2 to 126 (not on first pass products). When
SLOW = 0, the divider is bypassed. The generation of E, P and
M clocks further divides SLWCLK by 2. Hence, the final ratio of Bus
to EXTALi Frequency is programmable to 2, 4, 8, 12, 16, 20, ..., 252,
by steps of 4. SLWCLK is a 50% duty cycle signal.
Technical Data
178
MC68HC912DG128 — Rev 3.0
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Clock Functions
System Clock Frequency formulas
11.7 System Clock Frequency formulas
See Figure 11-6:
SLWCLK = EXTALi / ( 2 x SLOW )
SLOW = 1,2,..63
SLWCLK = EXTALi
SLOW = 0
PLLCLK = 2 x EXTALi x (SYNR + 1) / (REFDV + 1)
Freescale Semiconductor, Inc...
ECLK = SYSCLK / 2
XCLK = SLWCLK / 2
PCLK = SYSCLK / 2
BCLK(1) = EXTALi / 2
Boolean equations:
SYSCLK = (BCSP & PLLCLK) | (BCSP & BCSS & EXTALi) | (BCSP &
BCSS & SLWCLK)
MCLK = (PCLK & MCS) | (XCLK & MCS)
MSCAN system = (EXTALi & CLKSRC) | (SYSCLK & CLKSRC)
BDM system = (BCLK & CLKSW) | (ECLK & CLKSW)
NOTE:
During limp-home mode PCLK, ECLK, BCLK, MCLK and XCLK are
supplied by VCO (PLLCLK).
1. If SYSCLK is slower than EXTALi (BCSS=1, BCSP=0, SLOW>0), BCLK becomes ECLK.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
179
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Clock Functions
11.8 Clock Divider Chains
Figure 11-6, Figure 11-7, Figure 11-8, and Figure 11-9 summarize the
clock divider chains for the various peripherals on the
68HC(9)12DG128.
BCSP BCSS
1:x
PHASE
LOCK
LOOP
SYSCLK
PLLCLK
÷2
EXTALi
EXTAL
BCSP BCSS
0:0
REDUCED
CONSUMPTION
OSCILLATOR
T CLOCK
GENERATOR
TCLKs
E AND P
CLOCK
GENERATOR
ECLK
PCLK
EXTALi
TO CPU
TO
BUSES,
SPI,
PWM,
ATD0, ATD1
CLKSRC = 1
BCSP BCSS
0:1
XTAL
EXTALi
TO
MSCAN
CLKSRC = 0
MCS = 0
MCLK
MCS = 1
SLOW MODE
CLOCK
DIVIDER
SLWCLK
÷2
TO
SCI0, SCI1,
ECT
SYNC
XCLK
TO
RTI, COP
TO CAL
CLKSW = 0
÷2
SYNC
BDMCLK
CLKSW = 1
TO BDM
TO CLOCK
MONITOR
Figure 11-6. Clock Generation Chain
Technical Data
180
MC68HC912DG128 — Rev 3.0
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Clock Functions
Clock Divider Chains
Bus clock select bits BCSP and BCSS in the clock select register
(CLKSEL) determine which clock drives SYSCLK for the main system
including the CPU and buses. BCSS has no effect if BCSP is set. During
the transition, the clock select output will be held low and all CPU activity
will cease until the transition is complete.
The Module Clock Select bit MCS determines the clock used by the ECT
module and the baud rate generators of the SCIs. In limp-home mode,
the output of MCS is forced to 0, but the MCS bit reads the latched value.
It allows normal operation of the serial and timer subsystems at a fixed
reference frequency while allowing the CPU to operate at a higher,
variable frequency.
XCLK
÷ 2048
÷4
REGISTER: RTICTL
BITS: RTR2, RTR1, RTR0
REGISTER: RTICTL
BIT:RTBYP
0:0:0
REGISTER: COPCTL
BITS: CR2, CR1, CR0
0:0:1
MCLK
SC0BD
MODULUS DIVIDER:
÷ 1, 2, 3, 4, 5, 6,...,8190, 8191
SCI0
RECEIVE
BAUD RATE (16x)
÷ 16
SCI0
TRANSMIT
BAUD RATE (1x)
SC1BD
MODULUS DIVIDER:
÷ 1, 2, 3, 4, 5, 6,...,8190, 8191
SCI1
RECEIVE
BAUD RATE (16x)
÷ 16
SCI1
TRANSMIT
BAUD RATE (1x)
0:0:0
0:0:1
÷2
0:1:0
÷4
0:1:0
÷2
0:1:1
÷4
0:1:1
÷2
1:0:0
÷4
1:0:0
÷2
1:0:1
÷4
1:0:1
÷2
1:1:0
÷2
1:1:0
÷2
1:1:1
÷2
1:1:1
TO RTI
TO COP
Figure 11-7. Clock Chain for SCI0, SCI1, RTI, COP
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
181
Freescale Semiconductor, Inc.
Clock Functions
MCLK
REGISTER: TMSK2
BITS: PR2, PR1, PR0
0:0:0
TEN
REGISTER: MCCTL
BITS: MCPR1, MCPR0
0:0
MCEN
÷2
0:0:1
÷4
0:1
÷2
0:1:0
÷2
1:0
÷2
0:1:1
÷2
1:1
MODULUS
DOWN
COUNTER
REGISTER: PACTL
BITS: PAEN, CLK1, CLK0
0:x:x
Freescale Semiconductor, Inc...
1:0:0
÷2
1:0:0
Prescaled MCLK
1:0:1
÷2
1:0:1
1:1:0
÷2
÷2
PULSE ACC
LOW BYTE
1:1:0
PACLK/256
1:1:1
PACLK/65536
(PAOV)
1:1:1
PACLK
GATE
LOGIC
PORT T7
PULSE ACC
HIGH BYTE
PAMOD
TO TIMER
MAIN
COUNTER
(TCNT)
PAEN
Figure 11-8. Clock Chain for ECT
Technical Data
182
MC68HC912DG128 — Rev 3.0
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Clock Functions
Clock Divider Chains
PCLK
5-BIT MODULUS
COUNTER (PR0-PR4)
÷2
÷2
TO ATD0
and ATD1
÷2
REGISTER: SP0BR
BITS: SPR2, SPR1, SPR0
0:0:0
SPI
BIT RATE
0:0:1
MSCAN
CLOCK
Freescale Semiconductor, Inc...
EXTALi
÷2
0:1:0
÷2
0:1:1
÷2
1:0:0
÷2
1:0:1
÷2
÷2
CLKSRC
SYSCLK
ECLK
CLKSW
1:1:0
BDM BIT CLOCK:
BCLK
BKGD IN
Receive: Detect falling edge,
count 12 ECLKs, Sample input
SYNCHRONIZER
1:1:1
BKGD DIRECTION
BKGD
PIN
LOGIC
BKGD OUT
Transmit 1: Detect falling edge,
count 6 ECLKs while output is
high impedance, Drive out 1 E
cycle pulse high, high impedance output again
Transmit 0: Detect falling edge,
Drive out low, count 9 ECLKs,
Drive out 1 E cycle pulse high,
high impedance output
Figure 11-9. Clock Chain for MSCAN, SPI, ATD0, ATD1 and BDM
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
183
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Clock Functions
11.9 Computer Operating Properly (COP)
The COP or watchdog timer is an added check that a program is running
and sequencing properly. When the COP is being used, software is
responsible for keeping a free running watchdog timer from timing out. If
the watchdog timer times out it is an indication that the software is no
longer being executed in the intended sequence; thus a system reset is
initiated. Three control bits allow selection of seven COP time-out
periods. When COP is enabled, sometime during the selected period the
program must write $55 and $AA (in this order) to the COPRST register.
If the program fails to do this the part will reset. If any value other than
$55 or $AA is written, the part is reset.
In addition, windowed COP operation can be selected. In this mode,
writes to the COPRST register must occur in the last 25% of the selected
period. A premature write will also reset the part.
11.10 Real-Time Interrupt
There is a real time (periodic) interrupt available to the user. This
interrupt will occur at one of seven selected rates. An interrupt flag and
an interrupt enable bit are associated with this function. There are three
bits for the rate select.
11.11 Clock Monitor
The clock monitor circuit is based on an internal resistor-capacitor (RC)
time delay. If no EXTALi clock edges are detected within this RC time
delay, the clock monitor can optionally generate a system reset. The
clock monitor function is enabled/disabled by the CME control bit in the
COPCTL register. This time-out is based on an RC delay so that the
clock monitor can operate without any EXTALi clock.
Technical Data
184
MC68HC912DG128 — Rev 3.0
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Clock Functions
Clock Function Registers
Clock monitor time-outs are shown in Table 11-3. The corresponding
EXTALi clock period with an ideal 50% duty cycle is twice this time-out
value.
Table 11-3. Clock Monitor Time-Outs
Supply
5 V +/– 10%
Range
2–20 µS
11.12 Clock Function Registers
All register addresses shown reflect the reset state. Registers may be
mapped to any 2K byte space.
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
RTIE
RSWAI
RSBCK
Reserved
RTBYP
RTR2
RTR1
RTR0
0
0
0
0
0
0
0
0
RTICTL — Real-Time Interrupt Control Register
$0014
RTIE — Real Time Interrupt Enable
Read and write anytime.
0 = Interrupt requests from RTI are disabled.
1 = Interrupt will be requested whenever RTIF is set.
RSWAI — RTI and COP Stop While in Wait
Write once in normal modes, anytime in special modes. Read
anytime.
0 = Allows the RTI and COP to continue running in wait.
1 = Disables both the RTI and COP whenever the part goes into
Wait.
RSBCK — RTI and COP Stop While in Background Debug Mode
Write once in normal modes, anytime in special modes. Read
anytime.
0 = Allows the RTI and COP to continue running while in
background mode.
1 = Disables both the RTI and COP when the part is in background
mode. This is useful for emulation.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
185
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Clock Functions
RTBYP — Real Time Interrupt Divider Chain Bypass
Write not allowed in normal modes, anytime in special modes. Read
anytime.
0 = Divider chain functions normally.
1 = Divider chain is bypassed, allows faster testing (the divider
chain is normally XCLK divided by 213, when bypassed
becomes XCLK divided by 4).
RTR2, RTR1, RTR0 — Real-Time Interrupt Rate Select
Read and write anytime.
Rate select for real-time interrupt. The clock used for this module is
the XCLK.
Table 11-4. Real Time Interrupt Rates
RTR2 RTR1 RTR0 Divide X By:
Time-Out Period Time-Out Period Time-Out Period Time-Out Period
X = 125 KHz
X = 500 KHz
X = 2.0 MHz
X = 8.0 MHz
OFF
OFF
OFF
OFF
0
0
0
OFF
0
0
1
213
65.536 ms
16.384 ms
4.096 ms
1.024 ms
0
2
14
131.72 ms
32.768 ms
8.196 ms
2.048 ms
2
15
263.44 ms
65.536 ms
16.384 ms
4.096 ms
16
526.88 ms
131.72 ms
32.768 ms
8.196 ms
0
0
1
1
1
1
0
0
2
1
0
1
217
1.05 s
263.44 ms
65.536 ms
16.384 ms
1
1
0
218
2.11 s
526.88 ms
131.72 ms
32.768 ms
1
1
1
219
4.22 s
1.05 s
263.44 ms
65.536 ms
Bit 7
6
5
4
3
2
1
Bit 0
RTIF
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
RESET:
RTIFLG — Real Time Interrupt Flag Register
$0015
RTIF — Real Time Interrupt Flag
This bit is cleared automatically by a write to this register with this bit
set.
0 = Time-out has not yet occurred.
1 = Set when the time-out period is met.
Technical Data
186
MC68HC912DG128 — Rev 3.0
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Clock Functions
Clock Function Registers
Bit 7
6
5
4
3
2
1
Bit 0
CME
FCME
FCMCOP
WCOP
DISR
CR2
CR1
CR0
RESET:
0/1
0
0
0
0
1
1
1
Normal
RESET:
0/1
0
0
0
1
1
1
1
Special
COPCTL — COP Control Register
$0016
CME — Clock Monitor Enable
Read and write anytime.
Freescale Semiconductor, Inc...
If FCME is set, this bit has no meaning nor effect.
0 = Clock monitor is disabled. Slow clocks and stop instruction may
be used.
1 = Slow or stopped clocks (including the stop instruction) will
cause a clock reset sequence or limp-home mode. See LimpHome and Fast STOP Recovery modes.
On reset
CME is 1 if VDDPLL is high
CME is 0 if VDDPLL is low.
NOTE:
The VDDPLL-dependent reset operation is not implemented on first
pass products.
In this case the state of CME on reset is 0.
FCME — Force Clock Monitor Enable
Write once in normal modes, anytime in special modes. Read
anytime.
In normal modes, when this bit is set, the clock monitor function
cannot be disabled until a reset occurs.
0 = Clock monitor follows the state of the CME bit.
1 = Slow or stopped clocks will cause a clock reset sequence or
limp-home mode.
See Limp-Home and Fast STOP Recovery modes.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
187
Freescale Semiconductor, Inc.
Clock Functions
FCMCOP — Force Clock Monitor Reset or COP Watchdog Reset
Writes are not allowed in normal modes, anytime in special modes.
Read anytime.
Freescale Semiconductor, Inc...
If DISR is set, this bit has no effect.
0 = Normal operation.
1 = A clock monitor failure reset or a COP failure reset is forced
depending on the state of CME and if COP is enabled.
CME
COP enabled
Forced reset
0
0
none
0
1
COP failure
1
0
Clock monitor failure
1
1
Both(1)
1. Highest priority interrupt vector is serviced.
WCOP — Window COP mode
Write once in normal modes, anytime in special modes. Read
anytime.
0 = Normal COP operation
1 = Window COP operation
When set, a write to the COPRST register must occur in the last 25%
of the selected period. A premature write will also reset the part. As
long as all writes occur during this window, $55 can be written as often
as desired. Once $AA is written the time-out logic restarts and the
user must wait until the next window before writing to COPRST.
Please note, there is a fixed time uncertainty about the exact COP
counter state when reset, as the initial prescale clock divider in the
RTI section is not cleared when the COP counter is cleared. This
means the effective window is reduced by this uncertainty. Table 115 below shows the exact duration of this window for the seven
available COP rates.
Technical Data
188
MC68HC912DG128 — Rev 3.0
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Clock Functions
Clock Function Registers
Table 11-5. COP Watchdog Rates
CR2
CR1
CR0
Window COP enabled:
Divide
X clock
by
8.0 MHz X clock.
Time-out
Window start
(1)
Window end
Effective
Window (2)
0
0
0
OFF
OFF
OFF
OFF
OFF
0
0
1
2 13
1.024 ms -0/+0.256 ms
0.768 ms
0.768 ms
0 % (3)
0
1
0
2 15
4.096 ms -0/+0.256 ms
3.072 ms
3.840 ms
18.8 %
0
1
1
2 17
16.384 ms -0/+0.256 ms
12.288 ms
16.128 ms
23.4 %
1
0
0
2 19
65.536 ms -0/+1.024 ms
49.152 ms
64.512 ms
23.4 %
1
0
1
2 21
262.144 ms -0/+1.024 ms
196.608 ms
261.120 ms
24.6 %
1
1
0
2 22
524.288 ms -0/+1.024 ms
393.216 ms
523.264 ms
24.8 %
1
1
1
2 23
1.048576 ms -0/+1.024 ms
786.432 ms
1.047552 ms
24.9 %
1. Time for writing $55 following previous COP restart of time-out logic due to writing $AA.
2. Please refer to WCOP bit description above.
3. Window COP cannot be used at this rate.
DISR — Disable Resets from COP Watchdog and Clock Monitor
Writes are not allowed in normal modes, anytime in special modes.
Read anytime.
0 = Normal operation.
1 = Regardless of other control bit states, COP and clock monitor
will not generate a system reset.
CR2, CR1, CR0 — COP Watchdog Timer Rate select bits
These bits select the COP time-out rate. The clock used for this
module is the XCLK.
Write once in normal modes, anytime in special modes. Read
anytime.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
189
Freescale Semiconductor, Inc.
Clock Functions
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
RESET:
COPRST — Arm/Reset COP Timer Register
$0017
Always reads $00.
Freescale Semiconductor, Inc...
Writing $55 to this address is the first step of the COP watchdog
sequence.
Writing $AA to this address is the second step of the COP watchdog
sequence. Other instructions may be executed between these writes
but both must be completed in the correct order prior to time-out to
avoid a watchdog reset. Writing anything other than $55 or $AA
causes a COP reset to occur.
Technical Data
190
MC68HC912DG128 — Rev 3.0
Clock Functions
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Section 12. Pulse Width Modulator
12.1 Contents
12.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 191
12.3
PWM Register Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 195
12.4
PWM Boundary Cases . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 206
12.2 Introduction
The pulse-width modulator (PWM) subsystem provides four
independent 8-bit PWM waveforms or two 16-bit PWM waveforms or a
combination of one 16-bit and two 8-bit PWM waveforms. Each
waveform channel has a programmable period and a programmable
duty-cycle as well as a dedicated counter. A flexible clock select scheme
allows four different clock sources to be used with the counters. Each of
the modulators can create independent, continuous waveforms with
software-selectable duty rates from 0 percent to 100 percent. The PWM
outputs can be programmed as left-aligned outputs or center-aligned
outputs.
The period and duty registers are double buffered so that if they change
while the channel is enabled, the change will not take effect until the
counter rolls over or the channel is disabled. If the channel is not
enabled, then writes to the period and/or duty register will go directly to
the latches as well as the buffer, thus ensuring that the PWM output will
always be either the old waveform or the new waveform, not some
variation in between.
A change in duty or period can be forced into immediate effect by writing
the new value to the duty and/or period registers and then writing to the
counter. This causes the counter to reset and the new duty and/or period
values to be latched. In addition, since the counter is readable it is
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Pulse Width Modulator
For More Information On This Product,
Go to: www.freescale.com
191
Freescale Semiconductor, Inc.
Pulse Width Modulator
possible to know where the count is with respect to the duty value and
software can be used to make adjustments by turning the enable bit off
and on.
The four PWM channel outputs share general-purpose port P pins.
Enabling PWM pins takes precedence over the general-purpose port.
When PWM channels are not in use, the port pins may be used for
discrete input/output.
Freescale Semiconductor, Inc...
CLOCK SOURCE
(ECLK or Scaled ECLK)
CENTR = 0
FROM PORT P
DATA REGISTER
UP/DOWN
PWCNTx
GATE
(CLOCK EDGE SYNC)
RESET
8-BIT COMPARE =
PWDTYx
S
Q
MUX
MUX
Q
8-BIT COMPARE =
PWPERx
PWENx
TO PIN
DRIVER
R
PPOLx
SYNC
PPOL = 0
PPOL = 1
PWDTY
PWPER
Figure 12-1. Block Diagram of PWM Left-Aligned Output Channel
Technical Data
192
MC68HC912DG128 — Rev 3.0
Pulse Width Modulator
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pulse Width Modulator
Introduction
CLOCK SOURCE
(ECLK or Scaled ECLK)
CENTR = 1
FROM PORT P
DATA REGISTER
RESET
PWCNTx
GATE
(CLOCK EDGE SYNC)
UP/DOWN
(DUTY CYCLE)
8-BIT COMPARE =
PWDTYx
T
Q
(PERIOD)
MUX
MUX
Q
TO PIN
DRIVER
8-BIT COMPARE =
PWPERx
PPOLx
PWENx
SYNC
PPOL = 1
PPOL = 0
PWDTY
(PWPER − PWDTY) × 2
PWPER × 2
PWDTY
Figure 12-2. Block Diagram of PWM Center-Aligned Output Channel
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Pulse Width Modulator
For More Information On This Product,
Go to: www.freescale.com
193
Freescale Semiconductor, Inc.
Pulse Width Modulator
PSBCK
PSBCK IS BIT 0 OF PWCTL REGISTER.
INTERNAL SIGNAL LIMBDM IS ONE IF THE MCU IS IN BACKGROUND DEBUG MODE.
LIMBDM
CLOCK A
MUX
ECLK
0:0:0
8-BIT DOWN COUNTER
0:1:0
÷2
÷2
0:0:1
PWSCNT0
0:1:0
Freescale Semiconductor, Inc...
8-BIT SCALE REGISTER
0:1:1
÷2
0:1:1
1:0:0
÷2
1:0:0
PCLK0
MUX
0:0:1
=0
CLOCK S0*
0:0:0
PCLK1
1:0:1
1:1:0
÷2
1:1:0
1:1:1
÷2
1:1:1
MUX
÷2
8-BIT DOWN COUNTER
BITS:
PCKA2,
PCKA1,
PCKA0
CLOCK S1**
8-BIT SCALE REGISTER
PWSCAL1
PCLK2
MUX
REGISTER:
PWPRES
CLOCK TO PWM
CHANNEL 2
=0
PWSCNT1
BITS:
PCKB2,
PCKB1,
PCKB0
CLOCK TO PWM
CHANNEL 1
÷2
PWSCAL0
CLOCK B
1:0:1
CLOCK TO PWM
CHANNEL 0
CLOCK TO PWM
CHANNEL 3
÷2
*CLOCK S0 = (CLOCK A)/2, (CLOCK A)/4, (CLOCK A)/6,... (CLOCK A)/512
**CLOCK S1 = (CLOCK B)/2, (CLOCK B)/4, (CLOCK B)/6,... (CLOCK B)/512
PCLK3
Figure 12-3. PWM Clock Sources
Technical Data
194
MC68HC912DG128 — Rev 3.0
Pulse Width Modulator
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Pulse Width Modulator
PWM Register Description
12.3 PWM Register Description
PWCLK — PWM Clocks and Concatenate
RESET:
$0040
Bit 7
6
5
4
3
2
1
Bit 0
CON23
CON01
PCKA2
PCKA1
PCKA0
PCKB2
PCKB1
PCKB0
0
0
0
0
0
0
0
0
Read and write anytime.
CON23 — Concatenate PWM Channels 2 and 3
Freescale Semiconductor, Inc...
When concatenated, channel 2 becomes the high-order byte and
channel 3 becomes the low-order byte. Channel 2 output pin is used
as the output for this 16-bit PWM (bit 2 of port P). Channel 3 clockselect control bits determines the clock source. Channel 3 output pin
becomes a general purpose I/O.
0 = Channels 2 and 3 are separate 8-bit PWMs.
1 = Channels 2 and 3 are concatenated to create one 16-bit PWM
channel.
CON01 — Concatenate PWM Channels 0 and 1
When concatenated, channel 0 becomes the high-order byte and
channel 1 becomes the low-order byte. Channel 0 output pin is used
as the output for this 16-bit PWM (bit 0 of port P). Channel 1 clockselect control bits determine the clock source. Channel 1 output pin
becomes a general purpose I/O.
0 = Channels 0 and 1 are separate 8-bit PWMs.
1 = Channels 0 and 1 are concatenated to create one 16-bit PWM
channel.
PCKA2 – PCKA0 — Prescaler for Clock A
Clock A is one of two clock sources which may be used for channels
0 and 1. These three bits determine the rate of clock A, as shown in
Table 12-1.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Pulse Width Modulator
For More Information On This Product,
Go to: www.freescale.com
195
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pulse Width Modulator
PCKB2 – PCKB0 — Prescaler for Clock B
Clock B is one of two clock sources which may be used for channels
2 and 3. These three bits determine the rate of clock B, as shown in
Table 12-1.
Table 12-1. Clock A and Clock B Prescaler
PCKA2 PCKA1 PCKA0
(PCKB2) (PCKB1) (PCKB0)
0
0
0
0
0
1
0
1
0
0
1
1
1
0
0
1
0
1
1
1
0
1
1
1
Value of
Clock A (B)
P
P÷2
P÷4
P÷8
P ÷ 16
P ÷ 32
P ÷ 64
P ÷ 128
Bit 7
6
5
4
3
2
1
Bit 0
PCLK3
PCLK2
PCLK1
PCLK0
PPOL3
PPOL2
PPOL1
PPOL0
0
0
0
0
0
0
0
0
RESET:
PWPOL — PWM Clock Select and Polarity
$0041
Read and write anytime.
PCLK3 — PWM Channel 3 Clock Select
0 = Clock B is the clock source for channel 3.
1 = Clock S1 is the clock source for channel 3.
PCLK2 — PWM Channel 2 Clock Select
0 = Clock B is the clock source for channel 2.
1 = Clock S1 is the clock source for channel 2.
PCLK1 — PWM Channel 1 Clock Select
0 = Clock A is the clock source for channel 1.
1 = Clock S0 is the clock source for channel 1.
Technical Data
196
MC68HC912DG128 — Rev 3.0
Pulse Width Modulator
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Pulse Width Modulator
PWM Register Description
PCLK0 — PWM Channel 0 Clock Select
0 = Clock A is the clock source for channel 0.
1 = Clock S0 is the clock source for channel 0.
If a clock select is changed while a PWM signal is being generated, a
truncated or stretched pulse may occur during the transition.
The following four bits apply in left-aligned mode only:
Freescale Semiconductor, Inc...
PPOL3 — PWM Channel 3 Polarity
0 = Channel 3 output is low at the beginning of the period; high
when the duty count is reached.
1 = Channel 3 output is high at the beginning of the period; low
when the duty count is reached.
PPOL2 — PWM Channel 2 Polarity
0 = Channel 2 output is low at the beginning of the period; high
when the duty count is reached.
1 = Channel 2 output is high at the beginning of the period; low
when the duty count is reached.
PPOL1 — PWM Channel 1 Polarity
0 = Channel 1 output is low at the beginning of the period; high
when the duty count is reached.
1 = Channel 1 output is high at the beginning of the period; low
when the duty count is reached.
PPOL0 — PWM Channel 0 Polarity
0 = Channel 0 output is low at the beginning of the period; high
when the duty count is reached.
1 = Channel 0 output is high at the beginning of the period; low
when the duty count is reached.
Depending on the polarity bit, the duty registers may contain the count
of either the high time or the low time. If the polarity bit is zero and left
alignment is selected, the duty registers contain a count of the low time.
If the polarity bit is one, the duty registers contain a count of the high
time.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Pulse Width Modulator
For More Information On This Product,
Go to: www.freescale.com
197
Freescale Semiconductor, Inc.
Pulse Width Modulator
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
PWEN3
PWEN2
PWEN1
PWEN0
0
0
0
0
0
0
0
0
RESET:
PWEN — PWM Enable
$0042
Freescale Semiconductor, Inc...
Setting any of the PWENx bits causes the associated port P line to
become an output regardless of the state of the associated data
direction register (DDRP) bit. This does not change the state of the data
direction bit. When PWENx returns to zero, the data direction bit controls
I/O direction. On the front end of the PWM channel, the scaler clock is
enabled to the PWM circuit by the PWENx enable bit being high. When
all four PWM channels are disabled, the prescaler counter shuts off to
save power. There is an edge-synchronizing gate circuit to guarantee
that the clock will only be enabled or disabled at an edge.
Read and write anytime.
PWEN3 — PWM Channel 3 Enable
The pulse modulated signal will be available at port P, bit 3 when its
clock source begins its next cycle.
0 = Channel 3 is disabled.
1 = Channel 3 is enabled.
PWEN2 — PWM Channel 2 Enable
The pulse modulated signal will be available at port P, bit 2 when its
clock source begins its next cycle.
0 = Channel 2 is disabled.
1 = Channel 2 is enabled.
PWEN1 — PWM Channel 1 Enable
The pulse modulated signal will be available at port P, bit 1 when its
clock source begins its next cycle.
0 = Channel 1 is disabled.
1 = Channel 1 is enabled.
Technical Data
198
MC68HC912DG128 — Rev 3.0
Pulse Width Modulator
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pulse Width Modulator
PWM Register Description
PWEN0 — PWM Channel 0 Enable
The pulse modulated signal will be available at port P, bit 0 when its
clock source begins its next cycle.
0 = Channel 0 is disabled.
1 = Channel 0 is enabled.
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
0
Bit 6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
PWPRES — PWM Prescale Counter
$0043
PWPRES is a free-running 7-bit counter. Read anytime. Write only in
special mode (SMOD = 1).
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
PWSCAL0 — PWM Scale Register 0
$0044
Read and write anytime. A write will cause the scaler counter PWSCNT0
to load the PWSCAL0 value unless in special mode with DISCAL = 1 in
the PWTST register.
PWM channels 0 and 1 can select clock S0 (scaled) as its input clock by
setting the control bit PCLK0 and PCLK1 respectively. Clock S0 is
generated by dividing clock A by the value in the PWSCAL0 register + 1
and dividing again by two. When PWSCAL0 = $FF, clock A is divided by
256 then divided by two to generate clock S0.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Pulse Width Modulator
For More Information On This Product,
Go to: www.freescale.com
199
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pulse Width Modulator
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
RESET:
PWSCNT0 — PWM Scale Counter 0 Value
$0045
PWSCNT0 is a down-counter that, upon reaching $00, loads the value
of PWSCAL0. Read any time.
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
RESET:
PWSCAL1 — PWM Scale Register 1
$0046
Read and write anytime. A write will cause the scaler counter PWSCNT1
to load the PWSCAL1 value unless in special mode with DISCAL = 1 in
the PWTST register.
PWM channels 2 and 3 can select clock S1 (scaled) as its input clock by
setting the control bit PCLK2 and PCLK3 respectively. Clock S1 is
generated by dividing clock B by the value in the PWSCAL1 register + 1
and dividing again by two. When PWSCAL1 = $FF, clock B is divided by
256 then divided by two to generate clock S1.
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
RESET:
PWSCNT1 — PWM Scale Counter 1 Value
$0047
PWSCNT1 is a down-counter that, upon reaching $00, loads the value
of PWSCAL1. Read any time.
Technical Data
200
MC68HC912DG128 — Rev 3.0
Pulse Width Modulator
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pulse Width Modulator
PWM Register Description
Bit 7
6
5
4
3
2
1
Bit 0
PWCNT0
Bit 7
6
5
4
3
2
1
Bit 0
$0048
PWCNT1
Bit 7
6
5
4
3
2
1
Bit 0
$0049
PWCNT2
Bit 7
6
5
4
3
2
1
Bit 0
$004A
PWCNT3
Bit 7
6
5
4
3
2
1
Bit 0
$004B
RESET:
0
0
0
0
0
0
0
0
PWCNTx — PWM Channel Counters
Read and write anytime. A write will cause the PWM counter to reset to
$00.
In special mode, if DISCR = 1, a write does not reset the PWM counter.
The PWM counters are not reset when PWM channels are disabled. The
counters must be reset prior to a new enable.
Each counter may be read any time without affecting the count or the
operation of the corresponding PWM channel. Writes to a counter cause
the counter to be reset to $00 and force an immediate load of both duty
and period registers with new values. To avoid a truncated PWM period,
write to a counter while the counter is disabled. In left-aligned output
mode, resetting the counter and starting the waveform output is
controlled by a match between the period register and the value in the
counter. In center-aligned output mode the counters operate as up/down
counters, where a match in period changes the counter direction. The
duty register changes the state of the output during the period to
determine the duty.
When a channel is enabled, the associated PWM counter starts at the
count in the PWCNTx register using the clock selected for that channel.
In special mode, when DISCP = 1 and configured for left-aligned output,
a match of period does not reset the associated PWM counter.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Pulse Width Modulator
For More Information On This Product,
Go to: www.freescale.com
201
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pulse Width Modulator
Bit 7
6
5
4
3
2
1
Bit 0
PWPER0
Bit 7
6
5
4
3
2
1
Bit 0
$004C
PWPER1
Bit 7
6
5
4
3
2
1
Bit 0
$004D
PWPER2
Bit 7
6
5
4
3
2
1
Bit 0
$004E
PWPER3
Bit 7
6
5
4
3
2
1
Bit 0
$004F
RESET:
1
1
1
1
1
1
1
1
PWPERx — PWM Channel Period Registers
Read and write anytime.
The value in the period register determines the period of the associated
PWM channel. If written while the channel is enabled, the new value will
not take effect until the existing period terminates, forcing the counter to
reset. The new period is then latched and is used until a new period
value is written. Reading this register returns the most recent value
written. To start a new period immediately, write the new period value
and then write the counter forcing a new period to start with the new
period value.
Period = Channel-Clock-Period × (PWPER + 1)
Period = Channel-Clock-Period × (2 × PWPER)
(CENTR = 0)
(CENTR = 1)
Bit 7
6
5
4
3
2
1
Bit 0
PWDTY0
Bit 7
6
5
4
3
2
1
Bit 0
$0050
PWDTY1
Bit 7
6
5
4
3
2
1
Bit 0
$0051
PWDTY2
Bit 7
6
5
4
3
2
1
Bit 0
$0052
PWDTY3
Bit 7
6
5
4
3
2
1
Bit 0
$0053
RESET:
1
1
1
1
1
1
1
1
PWDTYx — PWM Channel Duty Registers
Read and write anytime.
Technical Data
202
MC68HC912DG128 — Rev 3.0
Pulse Width Modulator
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pulse Width Modulator
PWM Register Description
The value in each duty register determines the duty of the associated
PWM channel. When the duty value is equal to the counter value, the
output changes state. If the register is written while the channel is
enabled, the new value is held in a buffer until the counter rolls over or
the channel is disabled. Reading this register returns the most recent
value written.
If the duty register is greater than or equal to the value in the period
register, there will be no duty change in state. If the duty register is set
to $FF the output will always be in the state which would normally be the
state opposite the PPOLx value.
Left-Aligned-Output Mode (CENTR = 0):
Duty cycle = [(PWDTYx + 1) / (PWPERx + 1)] × 100%
(PPOLx = 1)
Duty cycle = [(PWPERx−PWDTYx)/(PWPERx+1)] × 100% (PPOLx = 0)
Center-Aligned-Output Mode (CENTR = 1):
Duty cycle = [(PWPERx−PWDTYx)/PWPERx] × 100%
Duty cycle = [PWDTYx / PWPERx] × 100%
RESET:
(PPOLx = 0)
(PPOLx = 1)
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
PSWAI
CENTR
RDPP
PUPP
PSBCK
0
0
0
0
0
0
0
0
PWCTL — PWM Control Register
$0054
Read and write anytime.
PSWAI — PWM Halts while in Wait Mode
0 = Allows PWM main clock generator to continue while in wait
mode.
1 = Halt PWM main clock generator when the part is in wait mode.
CENTR — Center-Aligned Output Mode
To avoid irregularities in the PWM output mode, write the CENTR bit
only when PWM channels are disabled.
0 = PWM channels operate in left-aligned output mode
1 = PWM channels operate in center-aligned output mode
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Pulse Width Modulator
For More Information On This Product,
Go to: www.freescale.com
203
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pulse Width Modulator
RDPP — Reduced Drive of Port P
0 = All port P output pins have normal drive capability.
1 = All port P output pins have reduced drive capability.
PUPP — Pull-Up Port P Enable
0 = All port P pins have an active pull-up device disabled.
1 = All port P pins have an active pull-up device enabled.
PSBCK — PWM Stops while in Background Mode
0 = Allows PWM to continue while in background mode.
1 = Disable PWM input clock when the part is in background mode.
Bit 7
6
5
4
3
2
1
Bit 0
DISCR
DISCP
DISCAL
0
0
0
0
0
0
0
0
0
0
0
0
0
RESET:
PWTST — PWM Special Mode Register (“Test”)
$0055
Read anytime but write only in special mode (SMODN = 0). These bits
are available only in special mode and are reset in normal mode.
DISCR — Disable Reset of Channel Counter on Write to Channel
Counter
0 = Normal operation. Write to PWM channel counter will reset
channel counter.
1 = Write to PWM channel counter does not reset channel counter.
DISCP — Disable Compare Count Period
0 = Normal operation
1 = In left-aligned output mode, match of period does not reset the
associated PWM counter register.
DISCAL — Disable Load of Scale-Counters on Write to the Associated
Scale-Registers
0 = Normal operation
1 = Write to PWSCAL0 and PWSCAL1 does not load scale
counters
Technical Data
204
MC68HC912DG128 — Rev 3.0
Pulse Width Modulator
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Pulse Width Modulator
PWM Register Description
Bit 7
6
5
4
3
2
1
Bit 0
PP7
PP6
PP5
PP4
PP3
PP2
PP1
PP0
PWM
–
–
–
–
PWM3
PWM2
PWM1
PWM0
RESET:
–
–
–
–
–
–
–
–
PORTP — Port P Data Register
$0056
PORTP can be read anytime.
PWM functions share port P pins 3 to 0 and take precedence over the
general-purpose port when enabled.
When configured as input, a read will return the pin level. Port P[7:4] will
read as zero because there are no available external pins.
When configured as output, a read will return the latched output data.
Port P[7:4] will read the last value written.
A write will drive associated pins only if configured for output and the
corresponding PWM channel is not enabled.
After reset, all pins are general-purpose, high-impedance inputs.
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
DDP7
DDP6
DDP5
DDP4
DDP3
DDP2
DDP1
DDP0
0
0
0
0
0
0
0
0
DDRP — Port P Data Direction Register
$0057
DDRP determines pin direction of port P when used for general-purpose
I/O.
Read and write anytime.
DDRP[7:4] — Data Direction Port P pin 7–4
Serve as memory locations since there are no corresponding port pins.
DDRP[3:0] — Data Direction Port P pin 3–0
0 = I/O pin configured as high impedance input
1 = I/O pin configured for output.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Pulse Width Modulator
For More Information On This Product,
Go to: www.freescale.com
205
Freescale Semiconductor, Inc.
Pulse Width Modulator
12.4 PWM Boundary Cases
The boundary conditions for the PWM channel duty registers and the
PWM channel period registers cause these results:
Table 12-2. PWM Left-Aligned Boundary Conditions
Freescale Semiconductor, Inc...
PWDTYx
$FF
$FF
≥PWPERx
≥PWPERx
–
–
PWPERx
>$00
>$00
–
–
$00
$00
PPOLx
1
0
1
0
1
0
Output
Low
High
High
Low
High
Low
Table 12-3. PWM Center-Aligned Boundary Conditions
PWDTYx
$00
$00
≥PWPERx
≥PWPERx
–
–
PWPERx
>$00
>$00
–
–
$00
$00
PPOLx
1
0
1
0
1
0
Technical Data
206
Output
Low
High
High
Low
High
Low
MC68HC912DG128 — Rev 3.0
Pulse Width Modulator
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Section 13. Enhanced Capture Timer
13.1 Contents
13.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 207
13.3
Enhanced Capture Timer Modes of Operation . . . . . . . . . . . . 214
13.4
Timer Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 217
13.5
Timer and Modulus Counter Operation in Different Modes . . 247
13.2 Introduction
The HC12 Enhanced Capture Timer module has the features of the
HC12 Standard Timer module enhanced by additional features in order
to enlarge the field of applications, in particular for automotive ABS
applications.
The additional features permit the operation of this timer module in a
mode similar to the Input Control Timer implemented on
MC68HC11NB4.
These additional features are:
•
16-Bit Buffer Register for four Input Capture (IC) channels.
•
Four 8-Bit Pulse Accumulators with 8-bit buffer registers
associated with the four buffered IC channels. Configurable also
as two 16-Bit Pulse Accumulators.
•
16-Bit Modulus Down-Counter with 4-bit Prescaler.
•
Four user selectable Delay Counters for input noise immunity
increase.
•
Main Timer Prescaler extended to 7-bit.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
207
Freescale Semiconductor, Inc.
Enhanced Capture Timer
This design specification describes the standard timer as well as the
additional features.
The basic timer consists of a 16-bit, software-programmable counter
driven by a prescaler. This timer can be used for many purposes,
including input waveform measurements while simultaneously
generating an output waveform. Pulse widths can vary from
microseconds to many seconds.
Freescale Semiconductor, Inc...
A full access for the counter registers or the input capture/output
compare registers should take place in one clock cycle. Accessing high
byte and low byte separately for all of these registers may not yield the
same result as accessing them in one word.
Technical Data
208
MC68HC912DG128 — Rev 3.0
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Enhanced Capture Timer
Introduction
÷ 1, 2, ..., 128
M clock
16-bit Free-running
16 BIT MAIN
TIMER
main
timer
Prescaler
16-bit load register
÷ 1, 4, 8, 16
M clock
16-bit modulus
down counter
Prescaler
RESET
0
Pin logic
Delay counter
EDG0
Underflow
PT0
Comparator
TC0 capture/compare register
PAC0
TC0H hold register
PA0H hold register
RESET
0
PT1
Comparator
Pin logic
Delay counter
EDG1
TC1 capture/compare register
TC1H hold register
PAC1
PA1H hold register
RESET
0
PT2
Comparator
Pin logic
Delay counter
EDG2
TC2 capture/compare register
TC2H hold register
PAC2
PA2H hold register
RESET
0
PT3
Comparator
Pin logic
Delay counter
EDG3
TC3 capture/compare register
TC3H hold register
PT4
EDG4
ICLAT, LATQ, BUFEN
(force latch)
Comparator
Pin logic
EDG5
TC5 capture/compare register
MUX
Write $0000
to modulus counter
Comparator
Pin logic
EDG6
LATQ
(MDC latch enable)
TC6 capture/compare register
MUX
EDG2
PT7
TC4 capture/compare register
MUX
EDG1
PT6
PA3H hold register
Comparator
Pin logic
EDG0
PT5
PAC3
LATCH
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Comparator
Pin logic
EDG7
EDG3
TC7 capture/compare register
MUX
Figure 13-1. Timer Block Diagram in Latch Mode
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
209
Freescale Semiconductor, Inc.
Enhanced Capture Timer
÷1, 2, ..., 128
16-bit Free-running
16 BIT MAIN
TIMER
main
timer
Prescaler
16-bit load register
÷ 1, 4, 8, 16
M clock
16-bit modulus
down counter
Prescaler
0
Delay counter
EDG0
TC0 capture/compare register
PAC0
TC0H hold register
PA0H hold register
PT1
Pin logic
Delay counter
EDG1
TC1 capture/compare register
TC1H hold register
PAC1
PA1H hold register
0
PT2
Pin logic
EDG2
TC2 capture/compare register
TC2H hold register
PAC2
PA2H hold register
0
Pin logic
EDG3
TC3 capture/compare register
TC3H hold register
Pin logic
Comparator
EDG4
Pin logic
TC4 capture/compare register
PAC3
PA3H hold register
LATQ, BUFEN
(queue mode)
MUX
EDG0
PT5
RESET
Comparator
Delay counter
PT4
RESET
Comparator
Delay counter
PT3
RESET
Comparator
LATCH1
Freescale Semiconductor, Inc...
0
LATCH0
Pin logic
LATCH2
PT0
RESET
Comparator
LATCH3
M clock
Comparator
EDG5
Read TC3H
hold register
TC5 capture/compare register
MUX
EDG1
Read TC2H
hold register
PT6
Pin logic
Comparator
EDG6
MUX
EDG2
PT7
Pin logic
TC6 capture/compare register
Read TC1H
hold register
Comparator
EDG7
EDG3
TC7 capture/compare register
Read TC0H
hold register
MUX
Figure 13-2. Timer Block Diagram in Queue Mode
Technical Data
210
MC68HC912DG128 — Rev 3.0
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Enhanced Capture Timer
Introduction
Load holding register and reset pulse accumulator
0
EDG0
PT0
Edge detector
8-bit PAC0 (PACN0)
Delay counter
PA0H holding register
Interrupt
0
EDG1
PT1
Edge detector
8-bit PAC1 (PACN1)
Delay counter
PA1H holding register
Host CPU data bus
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
0
EDG2
PT2
Edge detector
8-bit PAC2 (PACN2)
Delay counter
PA2H holding register
Interrupt
0
EDG3
PT3
Edge detector
8-bit PAC3 (PACN3)
Delay counter
PA3H holding register
Figure 13-3. 8-Bit Pulse Accumulators Block Diagram
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
211
Freescale Semiconductor, Inc.
Enhanced Capture Timer
TIMCLK (Timer clock)
CLK1
CLK0
Clock select
(PAMOD)
Edge detector
PT7
PACLK
PACLK / 256
PACLK / 65536
Freescale Semiconductor, Inc...
Prescaled MCLK
4:1 MUX
Interrupt
8-bit PAC3 (PACN3)
8-bit PAC2 (PACN2)
MUX
PACA
M clock
Intermodule Bus
Divide by 64
Interrupt
8-bit PAC1 (PACN1)
8-bit PAC0 (PACN0)
Delay counter
PACB
Edge detector
PT0
Figure 13-4. 16-Bit Pulse Accumulators Block Diagram
Technical Data
212
MC68HC912DG128 — Rev 3.0
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
Introduction
Pulse accumulator A
PAD
OC7
(OM7=1 or OL7=1) or (OC7M7 = 1)
Figure 13-5. Block Diagram for Port7 with Output compare / Pulse Accumulator A
16-bit Main Timer
PTn
Edge detector
Delay counter
Set CnF Interrupt
TCn Input Capture Reg.
TCnH I.C. Holding Reg.
BUFEN • LATQ • TFMOD
Figure 13-6. C3F-C0F Interrupt Flag Setting
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
213
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
13.3 Enhanced Capture Timer Modes of Operation
The Enhanced Capture Timer has 8 Input Capture, Output Compare
(IC/OC) channels same as on the HC12 standard timer (timer channels
TC0 to TC7). When channels are selected as input capture by selecting
the IOSx bit in TIOS register, they are called Input Capture (IC)
channels.
Four IC channels are the same as on the standard timer with one capture
register which memorizes the timer value captured by an action on the
associated input pin.
Four other IC channels, in addition to the capture register, have also one
buffer called holding register. This permits to memorize two different
timer values without generation of any interrupt.
Four 8-bit pulse accumulators are associated with the four buffered IC
channels. Each pulse accumulator has a holding register to memorize
their value by an action on its external input. Each pair of pulse
accumulators can be used as a 16-bit pulse accumulator.
The 16-bit modulus down-counter can control the transfer of the IC
registers contents and the pulse accumulators to the respective holding
registers for a given period, every time the count reaches zero.
The modulus down-counter can also be used as a stand-alone time base
with periodic interrupt capability.
13.3.1 IC Channels
The IC channels are composed of four standard IC registers and four
buffered IC channels.
An IC register is empty when it has been read or latched into the
holding register.
A holding register is empty when it has been read.
Technical Data
214
MC68HC912DG128 — Rev 3.0
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
Enhanced Capture Timer Modes of Operation
13.3.1.1 Non-Buffered IC Channels
The main timer value is memorized in the IC register by a valid input pin
transition. If the corresponding NOVWx bit of the ICOVW register is
cleared, with a new occurrence of a capture, the contents of IC register
are overwritten by the new value.
If the corresponding NOVWx bit of the ICOVW register is set, the capture
register cannot be written unless it is empty.
This will prevent the captured value to be overwritten until it is read.
13.3.1.2 Buffered IC Channels
There are two modes of operations for the buffered IC channels.
•
IC Latch Mode:
When enabled (LATQ=1), the main timer value is memorized in the IC
register by a valid input pin transition.
The value of the buffered IC register is latched to its holding register by
the Modulus counter for a given period when the count reaches zero, by
a write $0000 to the modulus counter or by a write to ICLAT in the
MCCTL register.
If the corresponding NOVWx bit of the ICOVW register is cleared, with a
new occurrence of a capture, the contents of IC register are overwritten
by the new value. In case of latching, the contents of its holding register
are overwritten.
If the corresponding NOVWx bit of the ICOVW register is set, the capture
register or its holding register cannot be written by an event unless they
are empty (see IC Channels). This will prevent the captured value to be
overwritten until it is read or latched in the holding register.
•
IC Queue Mode:
When enabled (LATQ=0), the main timer value is memorized in the IC
register by a valid input pin transition.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
215
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
If the corresponding NOVWx bit of the ICOVW register is cleared, with a
new occurrence of a capture, the value of the IC register will be transferred
to its holding register and the IC register memorizes the new timer value.
If the corresponding NOVWx bit of the ICOVW register is set, the capture
register or its holding register cannot be written by an event unless they
are empty (see IC Channels).
In queue mode, reads of holding register will latch the corresponding
pulse accumulator value to its holding register.
13.3.2 Pulse Accumulators
There are four 8-bit pulse accumulators with four 8-bit holding registers
associated with the four IC buffered channels. A pulse accumulator
counts the number of active edges at the input of its channel.
The user can prevent 8-bit pulse accumulators counting further than $FF
by PACMX control bit in ICSYS ($AB). In this case a value of $FF means
that 255 counts or more have occurred.
Each pair of pulse accumulators can be used as a 16-bit pulse accumulator.
There are two modes of operation for the pulse accumulators.
13.3.2.1 Pulse Accumulator latch mode
The value of the pulse accumulator is transferred to its holding register
when the modulus down-counter reaches zero, a write $0000 to the
modulus counter or when the force latch control bit ICLAT is written.
At the same time the pulse accumulator is cleared.
13.3.2.2 Pulse Accumulator queue mode
When queue mode is enabled, reads of an input capture holding register
will transfer the contents of the associated pulse accumulator to its
holding register.
At the same time the pulse accumulator is cleared.
Technical Data
216
MC68HC912DG128 — Rev 3.0
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
Timer Registers
13.3.3 Modulus Down-Counter
The modulus down-counter can be used as a time base to generate a
periodic interrupt. It can also be used to latch the values of the IC
registers and the pulse accumulators to their holding registers.
The action of latching can be programmed to be periodic or only once.
13.4 Timer Registers
Input/output pins default to general-purpose I/O lines until an internal
function which uses that pin is specifically enabled. The timer overrides
the state of the DDR to force the I/O state of each associated port line
when an output compare using a port line is enabled. In these cases the
data direction bits will have no affect on these lines.
When a pin is assigned to output an on-chip peripheral function, writing
to this PORTT bit does not affect the pin but the data is stored in an
internal latch such that if the pin becomes available for general-purpose
output the driven level will be the last value written to the PORTT bit.
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
IOS7
IOS6
IOS5
IOS4
IOS3
IOS2
IOS1
IOS0
0
0
0
0
0
0
0
0
TIOS — Timer Input Capture/Output Compare Select
$0080
Read or write anytime.
IOS[7:0] — Input Capture or Output Compare Channel Configuration
0 = The corresponding channel acts as an input capture
1 = The corresponding channel acts as an output compare.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
217
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
Bit 7
6
5
4
3
2
1
Bit 0
FOC7
FOC6
FOC5
FOC4
FOC3
FOC2
FOC1
FOC0
0
0
0
0
0
0
0
0
RESET:
CFORC — Timer Compare Force Register
$0081
Read anytime but will always return $00 (1 state is transient). Write
anytime.
FOC[7:0] — Force Output Compare Action for Channel 7-0
A write to this register with the corresponding data bit(s) set causes
the action which is programmed for output compare “n” to occur
immediately. The action taken is the same as if a successful
comparison had just taken place with the TCn register except the
interrupt flag does not get set.
Bit 7
6
5
4
3
2
1
Bit 0
OC7M7
OC7M6
OC7M5
OC7M4
OC7M3
OC7M2
OC7M1
OC7M0
0
0
0
0
0
0
0
0
RESET:
OC7M — Output Compare 7 Mask Register
$0082
Read or write anytime.
The bits of OC7M correspond bit-for-bit with the bits of timer port
(PORTT). Setting the OC7Mn will set the corresponding port to be an
output port regardless of the state of the DDRTn bit when the
corresponding IOSn bit is set to be an output compare. This does not
change the state of the DDRT bits. At successful OC7, for each bit that
is set in OC7M, the corresponding data bit OC7D is stored to the
corresponding bit of the timer port.
NOTE:
OC7M has priority over output action on the timer port enabled by OMn
and OLn bits in TCTL1 and TCTL2. If an OC7M bit is set, it prevents the
action of corresponding OM and OL bits on the selected timer port.
Technical Data
218
MC68HC912DG128 — Rev 3.0
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
Timer Registers
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
OC7D7
OC7D6
OC7D5
OC7D4
OC7D3
OC7D2
OC7D1
OC7D0
0
0
0
0
0
0
0
0
OC7D — Output Compare 7 Data Register
$0083
Read or write anytime.
The bits of OC7D correspond bit-for-bit with the bits of timer port
(PORTT). When a successful OC7 compare occurs, for each bit that is
set in OC7M, the corresponding data bit in OC7D is stored to the
corresponding bit of the timer port.
When the OC7Mn bit is set, a successful OC7 action will override a
successful OC[6:0] compare action during the same cycle; therefore, the
OCn action taken will depend on the corresponding OC7D bit.
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
TCNT — Timer Count Register
$0084–$0085
The 16-bit main timer is an up counter.
A full access for the counter register should take place in one clock cycle.
A separate read/write for high byte and low byte will give a different result
than accessing them as a word.
Read anytime.
Write has no meaning or effect in the normal mode; only writable in
special modes (SMODN = 0).
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
219
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
The period of the first count after a write to the TCNT registers may be a
different size because the write is not synchronized with the prescaler
clock.
Bit 7
6
5
4
TEN
TSWAI
TSBCK
TFFCA
0
0
0
0
RESET:
3
2
1
Bit 0
0
0
0
0
TSCR — Timer System Control Register
$0086
Read or write anytime.
TEN — Timer Enable
0 = Disables the main timer, including the counter. Can be used for
reducing power consumption.
1 = Allows the timer to function normally.
If for any reason the timer is not active, there is no ÷64 clock for the
pulse accumulator since the E÷64 is generated by the timer prescaler.
TSWAI — Timer Module Stops While in Wait
0 = Allows the timer module to continue running during wait.
1 = Disables the timer module when the MCU is in the wait mode.
Timer interrupts cannot be used to get the MCU out of wait.
TSWAI also affects pulse accumulators and modulus down counters.
TSBCK — Timer and Modulus Counter Stop While in Background Mode
0 = Allows the timer and modulus counter to continue running while
in background mode.
1 = Disables the timer and modulus counter whenever the MCU is
in background mode. This is useful for emulation.
TBSCK does not stop the pulse accumulator.
TFFCA — Timer Fast Flag Clear All
0 = Allows the timer flag clearing to function normally.
1 = For TFLG1($8E), a read from an input capture or a write to the
output compare channel ($90–$9F) causes the corresponding
channel flag, CnF, to be cleared. For TFLG2 ($8F), any access
Technical Data
220
MC68HC912DG128 — Rev 3.0
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
Timer Registers
to the TCNT register ($84, $85) clears the TOF flag. Any
access to the PACN3 and PACN2 registers ($A2, $A3) clears
the PAOVF and PAIF flags in the PAFLG register ($A1). Any
access to the PACN1 and PACN0 registers ($A4, $A5) clears
the PBOVF flag in the PBFLG register ($B1). Any access to the
MCCNT register ($B6, $B7) clears the MCZF flag in the
MCFLG register ($A7). This has the advantage of eliminating
software overhead in a separate clear sequence. Extra care is
required to avoid accidental flag clearing due to unintended
accesses.
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
TQCR — Reserved
RESET:
$0087
Bit 7
6
5
4
3
2
1
Bit 0
OM7
OL7
OM6
OL6
OM5
OL5
OM4
OL4
0
0
0
0
0
0
0
0
TCTL1 — Timer Control Register 1
MC68HC912DG128 — Rev 3.0
MOTOROLA
$0088
Technical Data
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
221
Freescale Semiconductor, Inc.
Enhanced Capture Timer
Bit 7
6
5
4
3
2
1
Bit 0
OM3
OL3
OM2
OL2
OM1
OL1
OM0
OL0
0
0
0
0
0
0
0
0
RESET:
TCTL2 — Timer Control Register 2
$0089
Read or write anytime.
Freescale Semiconductor, Inc...
OMn — Output Mode
OLn — Output Level
These eight pairs of control bits are encoded to specify the output
action to be taken as a result of a successful OCn compare. When
either OMn or OLn is one, the pin associated with OCn becomes an
output tied to OCn regardless of the state of the associated DDRT bit.
NOTE:
To enable output action by OMn and OLn bits on the timer port, the
corresponding bit in OC7M should be cleared.
Table 13-1. Compare Result Output Action
OMn
0
0
1
1
OLn
0
1
0
1
Action
Timer disconnected from output pin logic
Toggle OCn output line
Clear OCn output line to zero
Set OCn output line to one
To operate the 16-bit pulse accumulators A and B (PACA and PACB)
independently of input capture or output compare 7 and 0 respectively
the user must set the corresponding bits IOSn = 1, OMn = 0 and OLn
= 0. OC7M7 or OC7M0 in the OC7M register must also be cleared.
Technical Data
222
MC68HC912DG128 — Rev 3.0
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
Timer Registers
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
EDG7B
EDG7A
EDG6B
EDG6A
EDG5B
EDG5A
EDG4B
EDG4A
0
0
0
0
0
0
0
0
TCTL3 — Timer Control Register 3
RESET:
$008A
Bit 7
6
5
4
3
2
1
Bit 0
EDG3B
EDG3A
EDG2B
EDG2A
EDG1B
EDG1A
EDG0B
EDG0A
0
0
0
0
0
0
0
0
TCTL4 — Timer Control Register 4
$008B
Read or write anytime.
EDGnB, EDGnA — Input Capture Edge Control
These eight pairs of control bits configure the input capture edge
detector circuits.
Table 13-2Edge Detector Circuit Configuration
RESET:
EDGnB
0
0
1
1
EDGnA
0
1
0
1
Configuration
Capture disabled
Capture on rising edges only
Capture on falling edges only
Capture on any edge (rising or falling)
Bit 7
6
5
4
3
2
1
Bit 0
C7I
C6I
C5I
C4I
C3I
C2I
C1I
C0I
0
0
0
0
0
0
0
0
TMSK1 — Timer Interrupt Mask 1
$008C
Read or write anytime.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
223
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
The bits in TMSK1 correspond bit-for-bit with the bits in the TFLG1 status
register. If cleared, the corresponding flag is disabled from causing a
hardware interrupt. If set, the corresponding flag is enabled to cause a
hardware interrupt.
Read or write anytime.
C7I–C0I — Input Capture/Output Compare “x” Interrupt Enable.
Bit 7
6
5
4
3
2
1
Bit 0
TOI
0
PUPT
RDPT
TCRE
PR2
PR1
PR0
0
0
0
0
0
0
0
0
RESET:
TMSK2 — Timer Interrupt Mask 2
$008D
Read or write anytime.
TOI — Timer Overflow Interrupt Enable
0 = Interrupt inhibited
1 = Hardware interrupt requested when TOF flag set
PUPT — Timer Port Pull-Up Resistor Enable
This enable bit controls pull-up resistors on the timer port pins when
the pins are configured as inputs.
0 = Disable pull-up resistor function
1 = Enable pull-up resistor function
RDPT — Timer Port Drive Reduction
This bit reduces the effective output driver size which can reduce
power supply current and generated noise depending upon pin
loading.
0 = Normal output drive capability
1 = Enable output drive reduction function
TCRE — Timer Counter Reset Enable
This bit allows the timer counter to be reset by a successful output
compare 7 event. This mode of operation is similar to an up-counting
modulus counter.
Technical Data
224
MC68HC912DG128 — Rev 3.0
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Enhanced Capture Timer
Timer Registers
0 = Counter reset inhibited and counter free runs
1 = Counter reset by a successful output compare 7
If TC7 = $0000 and TCRE = 1, TCNT will stay at $0000 continuously.
If TC7 = $FFFF and TCRE = 1, TOF will never be set when TCNT is
reset from $FFFF to $0000.
PR2, PR1, PR0 — Timer Prescaler Select
Freescale Semiconductor, Inc...
These three bits specify the number of ÷2 stages that are to be
inserted between the module clock and the main timer counter.
Table 13-3. Prescaler Selection
PR2
PR1
PR0
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
Prescale
Factor
1
2
4
8
16
32
64
128
The newly selected prescale factor will not take effect until the next
synchronized edge where all prescale counter stages equal zero.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
225
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
Bit 7
6
5
4
3
2
1
Bit 0
C7F
C6F
C5F
C4F
C3F
C2F
C1F
C0F
0
0
0
0
0
0
0
0
RESET:
TFLG1 — Main Timer Interrupt Flag 1
$008E
TFLG1 indicates when interrupt conditions have occurred. To clear a bit
in the flag register, write a one to the bit.
Use of the TFMOD bit in the ICSYS register ($AB) in conjunction with the
use of the ICOVW register ($AA) allows a timer interrupt to be generated
after capturing two values in the capture and holding registers instead of
generating an interrupt for every capture.
Read anytime. Write used in the clearing mechanism (set bits cause
corresponding bits to be cleared). Writing a zero will not affect current
status of the bit.
When TFFCA bit in TSCR register is set, a read from an input capture or
a write into an output compare channel ($90–$9F) will cause the
corresponding channel flag CnF to be cleared.
C7F–C0F — Input Capture/Output Compare Channel “n” Flag.
Bit 7
6
5
4
3
2
1
Bit 0
TOF
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
RESET:
TFLG2 — Main Timer Interrupt Flag 2
$008F
TFLG2 indicates when interrupt conditions have occurred. To clear a bit
in the flag register, set the bit to one.
Read anytime. Write used in clearing mechanism (set bits cause
corresponding bits to be cleared).
Technical Data
226
MC68HC912DG128 — Rev 3.0
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
Timer Registers
Any access to TCNT will clear TFLG2 register if the TFFCA bit in TSCR
register is set.
TOF — Timer Overflow Flag
Set when 16-bit free-running timer overflows from $FFFF to $0000.
This bit is cleared automatically by a write to the TFLG2 register with
bit 7 set. (See also TCRE control bit explanation.)
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
Bit 7
6
5
4
3
2
1
Bit 0
TC0 — Timer Input Capture/Output Compare Register 0
$0090–$0091
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
Bit 7
6
5
4
3
2
1
Bit 0
TC1 — Timer Input Capture/Output Compare Register 1
$0092–$0093
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
Bit 7
6
5
4
3
2
1
Bit 0
TC2 — Timer Input Capture/Output Compare Register 2
$0094–$0095
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
Bit 7
6
5
4
3
2
1
Bit 0
TC3 — Timer Input Capture/Output Compare Register 3
MC68HC912DG128 — Rev 3.0
MOTOROLA
$0096–$0097
Technical Data
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
227
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
Bit 7
6
5
4
3
2
1
Bit 0
TC4 — Timer Input Capture/Output Compare Register 4
$0098–$0099
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
Bit 7
6
5
4
3
2
1
Bit 0
TC5 — Timer Input Capture/Output Compare Register 5
$009A–$009B
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
Bit 7
6
5
4
3
2
1
Bit 0
TC6 — Timer Input Capture/Output Compare Register 6
$009C–$009D
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
Bit 7
6
5
4
3
2
1
Bit 0
TC7 — Timer Input Capture/Output Compare Register 7
$009E–$009F
Depending on the TIOS bit for the corresponding channel, these
registers are used to latch the value of the free-running counter when
a defined transition is sensed by the corresponding input capture
edge detector or to trigger an output action for output compare.
Technical Data
228
MC68HC912DG128 — Rev 3.0
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
Timer Registers
Read anytime. Write anytime for output compare function. Writes to
these registers have no meaning or effect during input capture. All
timer input capture/output compare registers are reset to $0000.
RESET:
BIT 7
6
5
4
3
2
1
BIT 0
0
PAEN
PAMOD
PEDGE
CLK1
CLK0
PAOVI
PAI
0
0
0
0
0
0
0
0
PACTL — 16-Bit Pulse Accumulator A Control Register
$00A0
16-Bit Pulse Accumulator A (PACA) is formed by cascading the 8-bit
pulse accumulators PAC3 and PAC2.
When PAEN is set, the PACA is enabled. The PACA shares the input pin
with IC7.
Read: any time
Write: any time
PAEN — Pulse Accumulator A System Enable
0 = 16-Bit Pulse Accumulator A system disabled. 8-bit PAC3 and
PAC2 can be enabled when their related enable bits in
ICPACR ($A8) are set.
Pulse Accumulator Input Edge Flag (PAIF) function is
disabled.
1 = Pulse Accumulator A system enabled. The two 8-bit pulse
accumulators PAC3 and PAC2 are cascaded to form the
PACA 16-bit pulse accumulator. When PACA in enabled, the
PACN3 and PACN2 registers contents are respectively the
high and low byte of the PACA.
PA3EN and PA2EN control bits in ICPACR ($A8) have no
effect.
Pulse Accumulator Input Edge Flag (PAIF) function is enabled.
PAEN is independent from TEN. With timer disabled, the pulse
accumulator can still function unless pulse accumulator is disabled.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
229
Freescale Semiconductor, Inc.
Enhanced Capture Timer
PAMOD — Pulse Accumulator Mode
0 = event counter mode
1 = gated time accumulation mode
PEDGE — Pulse Accumulator Edge Control
For PAMOD bit = 0 (event counter mode).
0 = falling edges on PT7 pin cause the count to be incremented
1 = rising edges on PT7 pin cause the count to be incremented
Freescale Semiconductor, Inc...
For PAMOD bit = 1 (gated time accumulation mode).
0 = PT7 input pin high enables M divided by 64 clock to Pulse
Accumulator and the trailing falling edge on PT7 sets the PAIF
flag.
1 = PT7 input pin low enables M divided by 64 clock to Pulse
Accumulator and the trailing rising edge on PT7 sets the PAIF
flag.
PAMOD
PEDGE
Pin Action
0
0
0
1
Rising edge
1
0
Div. by 64 clock enabled with pin high level
1
1
Div. by 64 clock enabled with pin low level
Falling edge
If the timer is not active (TEN = 0 in TSCR), there is no divide-by-64
since the E÷64 clock is generated by the timer prescaler.
CLK1, CLK0 — Clock Select Bits
CLK1
CLK0
Clock Source
0
0
Use timer prescaler clock as timer counter clock
0
1
Use PACLK as input to timer counter clock
1
0
Use PACLK/256 as timer counter clock frequency
1
1
Use PACLK/65536 as timer counter clock
frequency
If the pulse accumulator is disabled (PAEN = 0), the prescaler clock
from the timer is always used as an input clock to the timer counter.
The change from one selected clock to the other happens
immediately after these bits are written.
Technical Data
230
MC68HC912DG128 — Rev 3.0
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
Timer Registers
PAOVI — Pulse Accumulator A Overflow Interrupt enable
0 = interrupt inhibited
1 = interrupt requested if PAOVF is set
PAI — Pulse Accumulator Input Interrupt enable
0 = interrupt inhibited
1 = interrupt requested if PAIF is set
RESET:
BIT 7
6
5
4
3
2
1
BIT 0
0
0
0
0
0
0
PAOVF
PAIF
0
0
0
0
0
0
0
0
PAFLG — Pulse Accumulator A Flag Register
$00A1
Read or write anytime. When the TFFCA bit in the TSCR register is set,
any access to the PACNT register will clear all the flags in the PAFLG
register.
PAOVF — Pulse Accumulator A Overflow Flag
Set when the 16-bit pulse accumulator A overflows from $FFFF to
$0000,or when 8-bit pulse accumulator 3 (PAC3) overflows from $FF
to $00.
This bit is cleared automatically by a write to the PAFLG register with
bit 1 set.
PAIF — Pulse Accumulator Input edge Flag
Set when the selected edge is detected at the PT7 input pin. In event
mode the event edge triggers PAIF and in gated time accumulation
mode the trailing edge of the gate signal at the PT7 input pin triggers
PAIF.
This bit is cleared by a write to the PAFLG register with bit 0 set.
Any access to the PACN3, PACN2 registers will clear all the flags in
this register when TFFCA bit in register TSCR($86) is set.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
231
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
BIT 7
6
5
4
3
2
1
BIT 0
$00A2
BIt 7
6
5
4
3
2
1
Bit 0
PACN3 (hi)
$00A3
Bit 7
6
5
4
3
2
1
Bit 0
PACN2 (lo)
RESET:
0
0
0
0
0
0
0
0
PACN3, PACN2 — Pulse Accumulators Count Registers
$00A2, $00A3
Read: any time
Write: any time
The two 8-bit pulse accumulators PAC3 and PAC2 are cascaded to form
the PACA 16-bit pulse accumulator. When PACA in enabled (PAEN=1
in PACTL, $A0) the PACN3 and PACN2 registers contents are
respectively the high and low byte of the PACA.
When PACN3 overflows from $FF to $00, the Interrupt flag PAOVF in
PAFLG ($A1) is set.
Full count register access should take place in one clock cycle. A
separate read/write for high byte and low byte will give a different result
than accessing them as a word.
BIT 7
6
5
4
3
2
1
BIT 0
$00A4
BIt 7
6
5
4
3
2
1
Bit 0
PACN1 (hi)
$00A5
Bit 7
6
5
4
3
2
1
Bit 0
PACN0 (lo)
RESET:
0
0
0
0
0
0
0
0
PACN1, PACN0 — Pulse Accumulators Count Registers
$00A4, $00A5
Read: any time
Write: any time
The two 8-bit pulse accumulators PAC1 and PAC0 are cascaded to form
the PACB 16-bit pulse accumulator. When PACB in enabled, (PBEN=1
Technical Data
232
MC68HC912DG128 — Rev 3.0
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
Timer Registers
in PBCTL, $B0) the PACN1 and PACN0 registers contents are
respectively the high and low byte of the PACB.
When PACN1 overflows from $FF to $00, the Interrupt flag PBOVF in
PBFLG ($B1) is set.
Full count register access should take place in one clock cycle. A
separate read/write for high byte and low byte will give a different result
than accessing them as a word.
RESET:
BIT 7
6
5
4
3
2
1
BIT 0
MCZI
MODMC
RDMCL
ICLAT
FLMC
MCEN
MCPR1
MCPR0
0
0
0
0
0
0
0
0
MCCTL — 16-Bit Modulus Down-Counter Control Register
$00A6
Read: any time
Write: any time
MCZI — Modulus Counter Underflow Interrupt Enable
0 = Modulus counter interrupt is disabled.
1 = Modulus counter interrupt is enabled.
MODMC — Modulus Mode Enable
0 = The counter counts once from the value written to it and will
stop at $0000.
1 = Modulus mode is enabled. When the counter reaches $0000,
the counter is loaded with the latest value written to the
modulus count register.
NOTE:
For proper operation, the MCEN bit should be cleared before modifying
the MODMC bit in order to reset the modulus counter to $FF.
RDMCL — Read Modulus Down-Counter Load
0 = Reads of the modulus count register will return the present
value of the count register.
1 = Reads of the modulus count register will return the contents of
the load register.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
233
Freescale Semiconductor, Inc.
Enhanced Capture Timer
ICLAT — Input Capture Force Latch Action
When input capture latch mode is enabled (LATQ and BUFEN bit in
ICSYS ($AB) are set), a write one to this bit immediately forces the
contents of the input capture registers TC0 to TC3 and their
corresponding 8-bit pulse accumulators to be latched into the
associated holding registers. The pulse accumulators will be
automatically cleared when the latch action occurs.
Freescale Semiconductor, Inc...
Writing zero to this bit has no effect. Read of this bit will return always
zero.
FLMC — Force Load Register into the Modulus Counter Count Register
This bit is active only when the modulus down-counter is enabled
(MCEN=1).
A write one into this bit loads the load register into the modulus
counter count register. This also resets the modulus counter
prescaler.
Write zero to this bit has no effect.
When MODMC=0, counter starts counting and stops at $0000.
Read of this bit will return always zero.
MCEN — Modulus Down-Counter Enable
0 = Modulus counter disabled.
1 = Modulus counter is enabled.
When MCEN=0, the counter is preset to $FFFF. This will prevent an
early interrupt flag when the modulus down-counter is enabled.
Technical Data
234
MC68HC912DG128 — Rev 3.0
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
Timer Registers
MCPR1, MCPR0 — Modulus Counter Prescaler select
These two bits specify the division rate of the modulus counter
prescaler.
The newly selected prescaler division rate will not be effective until a
load of the load register into the modulus counter count register
occurs.
RESET:
MCPR1
MCPR0
Prescaler division
rate
0
0
1
0
1
4
1
0
8
1
1
16
BIT 7
6
5
4
3
2
1
BIT 0
MCZF
0
0
0
POLF3
POLF2
POLF1
POLF0
0
0
0
0
0
0
0
0
MCFLG — 16-Bit Modulus Down-Counter FLAG Register
$00A7
Read: any time
Write: Only for clearing bit 7
MCZF — Modulus Counter Underflow Interrupt Flag
The flag is set when the modulus down-counter reaches $0000.
Writing a1 to this bit clears the flag (if TFFCA=0). Writing a zero has
no effect.
Any access to the MCCNT register will clear the MCZF flag in this
register when TFFCA bit in register TSCR($86) is set.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
235
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
POLF3 – POLF0 — First Input Capture Polarity Status
These are read only bits. Write to these bits has no effect.
Each status bit gives the polarity of the first edge which has caused
an input capture to occur after capture latch has been read.
Each POLFx corresponds to a timer PORTx input.
0 = The first input capture has been caused by a falling edge.
1 = The first input capture has been caused by a rising edge.
BIT 7
6
5
4
3
2
1
BIT 0
0
0
0
0
PA3EN
PA2EN
PA1EN
PA0EN
0
0
0
0
0
0
0
0
RESET:
ICPACR — Input Control Pulse Accumulators Control Register
$00A8
The 8-bit pulse accumulators PAC3 and PAC2 can be enabled only if
PAEN in PATCL ($A0) is cleared. If PAEN is set, PA3EN and PA2EN
have no effect.
The 8-bit pulse accumulators PAC1 and PAC0 can be enabled only if
PBEN in PBTCL ($B0) is cleared. If PBEN is set, PA1EN and PA0EN
have no effect.
Read: any time
Write: any time
PAxEN — 8-Bit Pulse Accumulator ‘x’ Enable
0 = 8-Bit Pulse Accumulator is disabled.
1 = 8-Bit Pulse Accumulator is enabled.
Technical Data
236
MC68HC912DG128 — Rev 3.0
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Enhanced Capture Timer
Timer Registers
RESET:
BIT 7
6
5
4
3
2
1
BIT 0
0
0
0
0
0
0
DLY1
DLY0
0
0
0
0
0
0
0
0
DLYCT — Delay Counter Control Register
$00A9
Freescale Semiconductor, Inc...
Read: any time
Write: any time
If enabled, after detection of a valid edge on input capture pin, the delay
counter counts the pre-selected number of M clock (module clock)
cycles, then it will generate a pulse on its output. The pulse is generated
only if the level of input signal, after the preset delay, is the opposite of
the level before the transition.This will avoid reaction to narrow input
pulses.
After counting, the counter will be cleared automatically.
Delay between two active edges of the input signal period should be
longer than the selected counter delay.
DLYx — Delay Counter Select
DLY1
DLY0
Delay
0
0
Disabled (bypassed)
0
1
256 M clock cycles
1
0
512 M clock cycles
1
1
1024 M clock cycles
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
237
Freescale Semiconductor, Inc.
Enhanced Capture Timer
BIT 7
6
5
4
3
2
1
BIT 0
NOVW7
NOVW6
NOVW5
NOVW4
NOVW3
NOVW2
NOVW1
NOVW0
0
0
0
0
0
0
0
0
RESET:
ICOVW — Input Control Overwrite Register
$00AA
Freescale Semiconductor, Inc...
Read: any time
Write: any time
An IC register is empty when it has been read or latched into the holding
register.
A holding register is empty when it has been read.
NOVWx — No Input Capture Overwrite
0 = The contents of the related capture register or holding register
can be overwritten when a new input capture or latch occurs.
1 = The related capture register or holding register cannot be
written by an event unless they are empty (see IC Channels).
This will prevent the captured value to be overwritten until it is
read or latched in the holding register.
Technical Data
238
MC68HC912DG128 — Rev 3.0
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Enhanced Capture Timer
Timer Registers
RESET:
BIT 7
6
5
4
3
2
1
BIT 0
SH37
SH26
SH15
SH04
TFMOD
PACMX
BUFEN
LATQ
0
0
0
0
0
0
0
0
ICSYS — Input Control System Control Register
$00AB
Read: any time
Freescale Semiconductor, Inc...
Write: May be written once (SMODN=1). Writes are always permitted
when SMODN=0.
SHxy — Share Input action of Input Capture Channels x and y
0 = Normal operation
1 = The channel input ‘x’ causes the same action on the channel
‘y’. The port pin ‘x’ and the corresponding edge detector is
used to be active on the channel ‘y’.
TFMOD — Timer Flag-setting Mode
Use of the TFMOD bit in the ICSYS register ($AB) in conjunction with
the use of the ICOVW register ($AA) allows a timer interrupt to be
generated after capturing two values in the capture and holding
registers instead of generating an interrupt for every capture.
By setting TFMOD in queue mode, when NOVW bit is set and the
corresponding capture and holding registers are emptied, an input
capture event will first update the related input capture register with
the main timer contents. At the next event the TCn data is transferred
to the TCnH register, The TCn is updated and the CnF interrupt flag
is set. See Figure 13-6.
In all other input capture cases the interrupt flag is set by a valid
external event on PTn.
0 = The timer flags C3F–C0F in TFLG1 ($8E) are set when a valid
input capture transition on the corresponding port pin occurs.
1 = If in queue mode (BUFEN=1 and LATQ=0), the timer flags
C3F–C0F in TFLG1 ($8E) are set only when a latch on the
corresponding holding register occurs.
If the queue mode is not engaged, the timer flags C3F–C0F are
set the same way as for TFMOD=0.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
239
Freescale Semiconductor, Inc.
Enhanced Capture Timer
PACMX — 8-Bit Pulse Accumulators Maximum Count
0 = Normal operation. When the 8-bit pulse accumulator has
reached the value $FF, with the next active edge, it will be
incremented to $00.
1 = When the 8-bit pulse accumulator has reached the value $FF,
it will not be incremented further. The value $FF indicates a
count of 255 or more.
Freescale Semiconductor, Inc...
BUFEN — IC Buffer Enable
0 = Input Capture and pulse accumulator holding registers are
disabled.
1 = Input Capture and pulse accumulator holding registers are
enabled. The latching mode is defined by LATQ control bit.
Write one into ICLAT bit in MCCTL ($A6), when LATQ is set
will produce latching of input capture and pulse accumulators
registers into their holding registers.
LATQ — Input Control Latch or Queue Mode Enable
The BUFEN control bit should be set in order to enable the IC and
pulse accumulators holding registers. Otherwise LATQ latching
modes are disabled.
Write one into ICLAT bit in MCCTL ($A6), when LATQ and BUFEN
are set will produce latching of input capture and pulse accumulators
registers into their holding registers.
0 = Queue Mode of Input Capture is enabled.
The main timer value is memorized in the IC register by a valid
input pin transition.
With a new occurrence of a capture, the value of the IC register
will be transferred to its holding register and the IC register
memorizes the new timer value.
1 = Latch Mode is enabled. Latching function occurs when
modulus down-counter reaches zero or a zero is written into
the count register MCCNT (see Buffered IC Channels).
With a latching event the contents of IC registers and 8-bit
pulse accumulators are transferred to their holding registers.
8-bit pulse accumulators are cleared.
Technical Data
240
MC68HC912DG128 — Rev 3.0
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
Timer Registers
RESET:
BIT 7
6
5
4
3
2
1
BIT 0
0
0
0
0
0
0
TCBYP
0
0
0
0
0
0
0
0
0
TIMTST — Timer Test Register
$00AD
Read: any time
Write: only in special mode (SMOD = 1).
TCBYP — Main Timer Divider Chain Bypass
0 = Normal operation
1 = For testing only. The 16-bit free-running timer counter is divided
into two 8-bit halves and the prescaler is bypassed. The clock
drives both halves directly.
When the high byte of timer counter TCNT ($84) overflows
from $FF to $00, the TOF flag in TFLG2 ($8F) will be set.
BIT 7
6
5
4
3
2
1
BIT 0
PORT
PT7
PT6
PT5
PT4
PT3
PT2
PT1
PT0
TIMER
I/OC7
I/OC6
I/OC5
I/OC4
I/OC3
I/OC2
I/OC1
I/OC0
RESET:
0
0
0
0
0
0
0
0
PORTT — Timer Port Data Register
$00AE
Read: any time (inputs return pin level; outputs return data register
contents)
Write: data stored in an internal latch (drives pins only if configured for
output)
Since the Output Compare 7 shares the pin with Pulse Accumulator
input, the only way for Pulse accumulator to receive an independent
input from Output Compare 7 is setting both OM7 & OL7 to be zero, and
also OC7M7 in OC7M register to be zero.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
241
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
OC7 is still able to reset the counter if enabled while PT7 is used as input
to Pulse Accumulator.
PORTT can be read anytime. When configured as an input, a read will
return the pin level. When configured as an output, a read will return the
latched output data.
NOTE:
Writes do not change pin state when the pin is configured for timer
output. The minimum pulse width for pulse accumulator input should
always be greater than the width of two module clocks due to input
synchronizer circuitry. The minimum pulse width for the input capture
should always be greater than the width of two module clocks due to
input synchronizer circuitry.
BIT 7
6
5
4
3
2
1
BIT 0
DDT7
DDT6
DDT5
DDT4
DDT3
DDT2
DDT1
DDT0
0
0
0
0
0
0
0
0
RESET:
DDRT — Data Direction Register for Timer Port
$00AF
Read or write any time.
0 = Configures the corresponding I/O pin for input only
1 = Configures the corresponding I/O pin for output.
The timer forces the I/O state to be an output for each timer port line
associated with an enabled output compare. In these cases the data
direction bits will not be changed, but have no effect on the direction
of these pins. The DDRT will revert to controlling the I/O direction of
a pin when the associated timer output compare is disabled. Input
captures do not override the DDRT settings.
Technical Data
242
MC68HC912DG128 — Rev 3.0
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Enhanced Capture Timer
Timer Registers
RESET:
BIT 7
6
5
4
3
2
1
BIT 0
0
PBEN
0
0
0
0
PBOVI
0
0
0
0
0
0
0
0
0
PBCTL — 16-Bit Pulse Accumulator B Control Register
$00B0
Read: any time
Freescale Semiconductor, Inc...
Write: any time
16-Bit Pulse Accumulator B (PACB) is formed by cascading the 8-bit
pulse accumulators PAC1 and PAC0.
When PBEN is set, the PACB is enabled. The PACB shares the input
pin with IC0.
PBEN — Pulse Accumulator B System Enable
0 = 16-bit Pulse Accumulator system disabled. 8-bit PAC1 and
PAC0 can be enabled when their related enable bits in
ICPACR ($A8) are set.
1 = Pulse Accumulator B system enabled. The two 8-bit pulse
accumulators PAC1 and PAC0 are cascaded to form the
PACB 16-bit pulse accumulator. When PACB in enabled, the
PACN1 and PACN0 registers contents are respectively the
high and low byte of the PACB.
PA1EN and PA0EN control bits in ICPACR ($A8) have no
effect.
PBEN is independent from TEN. With timer disabled, the pulse
accumulator can still function unless pulse accumulator is disabled.
PBOVI — Pulse Accumulator B Overflow Interrupt enable
0 = interrupt inhibited
1 = interrupt requested if PBOVF is set
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
243
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
BIT 7
6
5
4
3
2
1
BIT 0
0
0
0
0
0
0
PBOVF
0
0
0
0
0
0
0
0
0
RESET:
PBFLG — Pulse Accumulator B Flag Register
$00B1
Read: any time
Write: any time
PBOVF — Pulse Accumulator B Overflow Flag
This bit is set when the 16-bit pulse accumulator B overflows from
$FFFF to $0000, or when 8-bit pulse accumulator 1 (PAC1) overflows
from $FF to $00.
This bit is cleared by a write to the PBFLG register with bit 1 set.
Any access to the PACN1 and PACN0 registers will clear the PBOVF
flag in this register when TFFCA bit in register TSCR($86) is set.
BIT 7
6
5
4
3
2
1
BIT 0
$00B2
BIt 7
6
5
4
3
2
1
Bit 0
PA3H
$00B3
Bit 7
6
5
4
3
2
1
Bit 0
PA2H
$00B4
BIt 7
6
5
4
3
2
1
Bit 0
PA1H
$00B5
Bit 7
6
5
4
3
2
1
Bit 0
PA0H
RESET:
0
0
0
0
0
0
0
0
PA3H–PA0H — 8-Bit Pulse Accumulators Holding Registers
$00B2–$00B5
Read: any time
Write: has no effect.
These registers are used to latch the value of the corresponding pulse
accumulator when the related bits in register ICPACR ($A8) are enabled
(see Pulse Accumulators).
Technical Data
244
MC68HC912DG128 — Rev 3.0
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Enhanced Capture Timer
Timer Registers
BIT 7
6
5
4
3
2
1
BIT 0
$00B6
BIt 15
14
13
12
11
10
9
Bit 8
MCCNTH
$00B7
Bit 7
6
5
4
3
2
1
Bit 0
MCCNTL
RESET:
1
1
1
1
1
1
1
1
MCCNTH/L — Modulus Down-Counter Count Register
$00B6, $00B7
Freescale Semiconductor, Inc...
Read: any time
Write: any time
A full access for the counter register should take place in one clock cycle.
A separate read/write for high byte and low byte will give different result
than accessing them as a word.
If the RDMCL bit in MCCTL register is cleared, reads of the MCCNT
register will return the present value of the count register. If the RDMCL
bit is set, reads of the MCCNT will return the contents of the load
register.
If a $0000 is written into MCCNT and modulus counter while LATQ and
BUFEN in ICSYS ($AB) register are set, the input capture and pulse
accumulator registers will be latched.
With a $0000 write to the MCCNT, the modulus counter will stay at zero
and does not set the MCZF flag in MCFLG register.
If modulus mode is enabled (MODMC=1), a write to this address will
update the load register with the value written to it. The count register will
not be updated with the new value until the next counter underflow.
The FLMC bit in MCCTL ($A6) can be used to immediately update the
count register with the new value if an immediate load is desired.
If modulus mode is not enabled (MODMC=0), a write to this address will
clear the prescaler and will immediately update the counter register with
the value written to it and down-counts once to $0000.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
245
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Enhanced Capture Timer
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
Bit 7
6
5
4
3
2
1
Bit 0
TC0H — Timer Input Capture Holding Register 0
$00B8–$00B9
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
Bit 7
6
5
4
3
2
1
Bit 0
TC1H — Timer Input Capture Holding Register 1
$00BA–$00BB
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
Bit 7
6
5
4
3
2
1
Bit 0
TC2H — Timer Input Capture Holding Register 2
$00BC–$00BD
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
Bit 7
6
5
4
3
2
1
Bit 0
TC3H — Timer Input Capture Holding Register 3
$00BE–$00BF
Read: any time
Write: has no effect.
These registers are used to latch the value of the input capture registers
TC0 – TC3. The corresponding IOSx bits in TIOS ($80) should be
cleared (see IC Channels).
Technical Data
246
MC68HC912DG128 — Rev 3.0
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Enhanced Capture Timer
13.5 Timer and Modulus Counter Operation in Different Modes
STOP:
Timer and modulus counter are off since clocks are stopped.
BGDM:
Timer and modulus counter keep on running, unless TSBCK
(REG$86, bit5) is set to one.
WAIT:
Counters keep on running, unless TSWAI in TSCR ($86) is
set to one.
Freescale Semiconductor, Inc...
NORMAL: Timer and modulus counter keep on running, unless TEN in
TSCR($86) respectively MCEN in MCCTL ($A6) are
cleared.
TEN=0:
All 16-bit timer operations are stopped, can only access the
registers.
MCEN=0: Modulus counter is stopped.
PAEN=1:
16-bit Pulse Accumulator A is active.
PAEN=0:
8-Bit Pulse Accumulators 3 and 2 can be enabled. (see
ICPACR)
PBEN=1:
16-bit Pulse Accumulator B is active.
PBEN=0:
8-Bit Pulse Accumulators 1 and 0 can be enabled. (see
ICPACR)
Technical Data
247
MC68HC912DG128 — Rev 3.0
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Enhanced Capture Timer
Technical Data
248
MC68HC912DG128 — Rev 3.0
Enhanced Capture Timer
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Section 14. Multiple Serial Interface
14.1 Contents
14.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 249
14.3
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 250
14.4
Serial Communication Interface (SCI) . . . . . . . . . . . . . . . . . . 250
14.5
Serial Peripheral Interface (SPI) . . . . . . . . . . . . . . . . . . . . . . . 262
14.6
Port S . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 271
14.2 Introduction
The multiple serial interface (MSI) module consists of three independent
serial I/O sub-systems: two serial communication interfaces (SCI0 and
SCI1) and the serial peripheral interface (SPI). Each serial pin shares
function with the general-purpose port pins of port S. The SCI
subsystems are NRZ type systems that are compatible with standard
RS-232 systems. These SCI systems have a new single wire operation
mode which allows the unused pin to be available as general-purpose
I/O. The SPI subsystem, which is compatible with the M68HC11 SPI,
includes new features such as SS output and bidirectional mode.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
249
Multiple Serial Interface
14.3 Block diagram
SCI0
SCI1
RxD0
PS0
TxD0
PS1
RxD1
TxD1
MISO/SISO
SPI
MOSI/MOMI
DDRS/IOCTLR
MSI
PORT S I/O DRIVERS
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
PS2
PS3
PS4
PS5
SCK
PS6
CS/SS
PS7
Figure 14-1. Multiple Serial Interface Block Diagram
14.4 Serial Communication Interface (SCI)
Two serial communication interfaces are available on the
MC68HC912DG128. These are NRZ format (one start, eight or nine
data, and one stop bit) asynchronous communication systems with
independent internal baud rate generation circuitry and SCI transmitters
and receivers. They can be configured for eight or nine data bits (one of
which may be designated as a parity bit, odd or even). If enabled, parity
is generated in hardware for transmitted and received data. Receiver
parity errors are flagged in hardware. The baud rate generator is based
on a modulus counter, allowing flexibility in choosing baud rates. There
is a receiver wake-up feature, an idle line detect feature, a loop-back
mode, and various error detection features. Two port pins for each SCI
provide the external interface for the transmitted data (TXD) and the
received data (RXD).
For a faster wake-up out of WAIT mode by a received SCI message,
both SCI have the capability of sending a receiver interrupt, if enabled,
when RAF (receiver active flag) is set. For compatibility with other
M68HC12 products, this feature is active only in WAIT mode and is
disabled when VDDPLL supply is at VSS level.
Technical Data
250
MC68HC912DG128 — Rev 3.0
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Multiple Serial Interface
Serial Communication Interface (SCI)
MCLK
BAUD RATE
CLOCK
SCI TRANSMITTER
MSB
DIVIDER
Rx Baud Rate
PARITY
GENERATOR
LSB
10-11 Bit SHIFT REG
TxD BUFFER/SCxDRL
SCxBD/SELECT
PIN CONTROL / DDRS / PORT S
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Tx Baud Rate
SCxCR1/SCI CTL 1
DATA BUS
TxMTR CONTROL
SCxCR2/SCI CTL 2
TxD
SCxSR1/INT STATUS
RxD
INT REQUEST LOGIC
TO
INTERNAL
LOGIC
PARITY
DETECT
DATA RECOVERY
SCI RECEIVER
MSB
LSB
10-11 BIT SHIFT REG
TxD BUFFER/SCxDRL
SCxCR1/SCI CTL 1
WAKE-UP LOGIC
SCxSR1/INT STATUS
SCxCR2/SCI CTL 2
INT REQUEST LOGIC
Figure 14-2. Serial Communications Interface Block Diagram
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
251
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Multiple Serial Interface
14.4.1 Data Format
The serial data format requires the following conditions:
•
An idle-line in the high state before transmission or reception of a
message.
•
A start bit (logic zero), transmitted or received, that indicates the
start of each character.
•
Data that is transmitted or received least significant bit (LSB) first.
•
A stop bit (logic one), used to indicate the end of a frame. (A frame
consists of a start bit, a character of eight or nine data bits and a
stop bit.)
•
A BREAK is defined as the transmission or reception of a logic
zero for one frame or more.
•
This SCI supports hardware parity for transmit and receive.
14.4.2 SCI Baud Rate Generation
The basis of the SCI baud rate generator is a 13-bit modulus counter.
This counter gives the generator the flexibility necessary to achieve a
reasonable level of independence from the CPU operating frequency
and still be able to produce standard baud rates with a minimal amount
of error. The clock source for the generator comes from the M Clock.
Table 14-1. Baud Rate Generation
Desired
SCI Baud Rate
110
300
600
1200
2400
4800
9600
14400
19200
38400
BR Divisor for
M = 4.0 MHz
2273
833
417
208
104
52
26
17
13
—
Technical Data
252
BR Divisor for
M = 8.0 MHz
4545
2273
833
417
208
104
52
35
26
13
MC68HC912DG128 — Rev 3.0
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Multiple Serial Interface
Serial Communication Interface (SCI)
14.4.3 SCI Register Descriptions
Control and data registers for the SCI subsystem are described below.
The memory address indicated for each register is the default address
that is in use after reset. Both SCI have identical control registers
mapped in two blocks of eight bytes.
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
BTST
BSPL
BRLD
SBR12
SBR11
SBR10
SBR9
SBR8
0
0
0
0
0
0
0
0
SC0BDH/SC1BDH — SCI Baud Rate Control Register
RESET:
High
$00C0/$00C8
Bit 7
6
5
4
3
2
1
Bit 0
SBR7
SBR6
SBR5
SBR4
SBR3
SBR2
SBR1
SBR0
0
0
0
0
0
1
0
0
SC0BDL/SC1BDL — SCI Baud Rate Control Register
Low
$00C1/$00C9
SCxBDH and SCxBDL are considered together as a 16-bit baud rate
control register.
Read any time. Write SBR[12:0] anytime. Low order byte must be written
for change to take effect. Write SBR[15:13] only in special modes. The
value in SBR[12:0] determines the baud rate of the SCI. The desired
baud rate is determined by the following formula:
MCLK
SCI Baud Rate = -------------------16 × BR
which is equivalent to:
MCLK
BR = -----------------------------------------------16 × SCI Baud Rate
BR is the value written to bits SBR[12:0] to establish baud rate.
NOTE:
The baud rate generator is disabled until TE or RE bit in SCxCR2
register is set for the first time after reset, and/or the baud rate generator
is disabled when SBR[12:0] = 0.
BTST — Reserved for test function
BSPL — Reserved for test function
BRLD — Reserved for test function
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
253
Freescale Semiconductor, Inc.
Multiple Serial Interface
Bit 7
6
5
4
3
2
1
Bit 0
LOOPS
WOMS
RSRC
M
WAKE
ILT
PE
PT
0
0
0
0
0
0
0
0
RESET:
SC0CR1/SC1CR1 — SCI Control Register 1
$00C2/$00CA
Read or write anytime.
Freescale Semiconductor, Inc...
LOOPS — SCI LOOP Mode/Single Wire Mode Enable
0 = SCI transmit and receive sections operate normally.
1 = SCI receive section is disconnected from the RXD pin and the
RXD pin is available as general purpose I/O. The receiver input is
determined by the RSRC bit. The transmitter output is controlled
by the associated DDRS bit. Both the transmitter and the receiver
must be enabled to use the LOOP or the single wire mode.
If the DDRS bit associated with the TXD pin is set during the LOOPS
= 1, the TXD pin outputs the SCI waveform. If the DDRS bit
associated with the TXD pin is clear during the LOOPS = 1, the TXD
pin becomes high (IDLE line state) for RSRC = 0 and high impedance
for RSRC = 1. Refer to Table 14-2.
WOMS — Wired-Or Mode for Serial Pins
This bit controls the two pins (TXD and RXD) associated with the SCIx
section.
0 = Pins operate in a normal mode with both high and low drive
capability. To affect the RXD bit, that bit would have to be
configured as an output (via DDS0/2) which is the single wire
case when using the SCI. WOMS bit still affects general-purpose
output on TXD and RXD pins when SCIx is not using these pins.
1 = Each pin operates in an open drain fashion if that pin is
declared as an output.
RSRC — Receiver Source
When LOOPS = 1, the RSRC bit determines the internal feedback
path for the receiver.
0 = Receiver input is connected to the transmitter internally (not
TXD pin)
1 = Receiver input is connected to the TXD pin
Technical Data
254
MC68HC912DG128 — Rev 3.0
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Multiple Serial Interface
Serial Communication Interface (SCI)
Table 14-2. Loop Mode Functions
LOOPS RSRC
0
x
1
0
1
0
1
0
DDSI(3)
x
0
1
1
1
1
0
1
1
1
1
1
1
WOMS
Function of Port S Bit 1/3
x
Normal Operations
0/1
LOOP mode without TXD output(TXD = High Impedance)
1
LOOP mode with TXD output (CMOS)
1
LOOP mode with TXD output (open-drain)
Single wire mode without TXD output
x
(the pin is used as receiver input only, TXD = High Impedance)
Single wire mode with TXD output
0
(the output is also fed back to receiver input, CMOS)
1
Single wire mode for the receiving and transmitting(open-drain)
M — Mode (select character format)
0 = One start, eight data, one stop bit
1 = One start, eight data, ninth data, one stop bit
WAKE — Wake-up by Address Mark/Idle
0 = Wake up by IDLE line recognition
1 = Wake up by address mark (last data bit set)
ILT — Idle Line Type
Determines which of two types of idle line detection will be used by
the SCI receiver.
0 = Short idle line mode is enabled.
1 = Long idle line mode is detected.
In the short mode, the SCI circuitry begins counting ones in the search
for the idle line condition immediately after the start bit. This means
that the stop bit and any bits that were ones before the stop bit could
be counted in that string of ones, resulting in earlier recognition of an
idle line.
In the long mode, the SCI circuitry does not begin counting ones in the
search for the idle line condition until a stop bit is received. Therefore,
the last byte’s stop bit and preceding “1” bits do not affect how quickly
an idle line condition can be detected.
PE — Parity Enable
0 = Parity is disabled.
1 = Parity is enabled.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
255
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Multiple Serial Interface
PT — Parity Type
If parity is enabled, this bit determines even or odd parity for both the
receiver and the transmitter.
0 = Even parity is selected. An even number of ones in the data
character causes the parity bit to be zero and an odd number
of ones causes the parity bit to be one.
1 = Odd parity is selected. An odd number of ones in the data
character causes the parity bit to be zero and an even number
of ones causes the parity bit to be one.
Bit 7
6
5
4
3
2
1
Bit 0
TIE
TCIE
RIE
ILIE
TE
RE
RWU
SBK
0
0
0
0
0
0
0
0
RESET:
SC0CR2/SC1CR2 — SCI Control Register 2
$00C3/$00CB
Read or write anytime.
TIE — Transmit Interrupt Enable
0 = TDRE interrupts disabled
1 = SCI interrupt will be requested whenever the TDRE status flag
is set.
TCIE — Transmit Complete Interrupt Enable
0 = TC interrupts disabled
1 = SCI interrupt will be requested whenever the TC status flag is
set.
RIE — Receiver Interrupt Enable
0 = RDRF and OR interrupts disabled, RAF interrupt in WAIT mode
disabled
1 = SCI interrupt will be requested whenever the RDRF or OR
status flag is set, or when RAF is set while in WAIT mode with
VDDPLL high.
ILIE — Idle Line Interrupt Enable
0 = IDLE interrupts disabled
1 = SCI interrupt will be requested whenever the IDLE status flag
is set.
Technical Data
256
MC68HC912DG128 — Rev 3.0
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Multiple Serial Interface
Serial Communication Interface (SCI)
TE — Transmitter Enable
0 = Transmitter disabled
1 = SCI transmit logic is enabled and the TXD pin (Port S bit 1/bit
3) is dedicated to the transmitter. The TE bit can be used to
queue an idle preamble.
RE — Receiver Enable
0 = Receiver disabled
1 = Enables the SCI receive circuitry.
RWU — Receiver Wake-Up Control
0 = Normal SCI Receiver
1 = Enables the wake-up function and inhibits further receiver
interrupts. Normally hardware wakes the receiver by
automatically clearing this bit.
SBK — Send Break
0 = Break generator off
1 = Generate a break code (at least 10 or 11 contiguous zeros).
As long as SBK remains set the transmitter will send zeros. When
SBK is changed to zero, the current frame of all zeros is finished
before the TxD line goes to the idle state. If SBK is toggled on and off,
the transmitter will send only 10 (or 11) zeros and then revert to mark
idle or sending data.
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
TDRE
TC
RDRF
IDLE
OR
NF
FE
PF
1
1
0
0
0
0
0
0
SC0SR1/SC1SR1 — SCI Status Register 1
$00C4/$00CC
The bits in these registers are set by various conditions in the SCI
hardware and are automatically cleared by special acknowledge
sequences. The receive related flag bits in SCxSR1 (RDRF, IDLE, OR,
NF, FE, and PF) are all cleared by a read of the SCxSR1 register
followed by a read of the transmit/receive data register low byte.
However, only those bits which were set when SCxSR1 was read will be
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
257
Freescale Semiconductor, Inc.
Multiple Serial Interface
cleared by the subsequent read of the transmit/receive data register low
byte. The transmit related bits in SCxSR1 (TDRE and TC) are cleared by
a read of the SCxSR1 register followed by a write to the transmit/receive
data registerl low byte.
Read anytime (used in auto clearing mechanism). Write has no meaning
or effect.
TDRE — Transmit Data Register Empty Flag
Freescale Semiconductor, Inc...
New data will not be transmitted unless SCxSR1 is read before writing
to the transmit data register. Reset sets this bit.
0 = SCxDR busy
1 = Any byte in the transmit data register is transferred to the serial
shift register so new data may now be written to the transmit
data register.
TC — Transmit Complete Flag
Flag is set when the transmitter is idle (no data, preamble, or break
transmission in progress). Clear by reading SCxSR1 with TC set and
then writing to SCxDR.
0 = Transmitter busy
1 = Transmitter is idle
RDRF — Receive Data Register Full Flag
Once cleared, IDLE is not set again until the RxD line has been active
and becomes idle again. RDRF is set if a received character is ready
to be read from SCxDR. Clear the RDRF flag by reading SCxSR1 with
RDRF set and then reading SCxDR.
0 = SCxDR empty
1 = SCxDR full
IDLE — Idle Line Detected Flag
Receiver idle line is detected (the receipt of a minimum of 10/11
consecutive ones). This bit will not be set by the idle line condition
when the RWU bit is set. Once cleared, IDLE will not be set again until
after RDRF has been set (after the line has been active and becomes
idle again).
0 = RxD line is idle
1 = RxD line is active
Technical Data
258
MC68HC912DG128 — Rev 3.0
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Multiple Serial Interface
Serial Communication Interface (SCI)
OR — Overrun Error Flag
New byte is ready to be transferred from the receive shift register to
the receive data register and the receive data register is already full
(RDRF bit is set). Data transfer is inhibited until this bit is cleared.
0 = No overrun
1 = Overrun detected
NF — Noise Error Flag
Freescale Semiconductor, Inc...
Set during the same cycle as the RDRF bit but not set in the case of
an overrun (OR).
0 = Unanimous decision
1 = Noise on a valid start bit, any of the data bits, or on the stop bit
FE — Framing Error Flag
Set when a zero is detected where a stop bit was expected. Clear the
FE flag by reading SCxSR1 with FE set and then reading SCxDR.
0 = Stop bit detected
1 = Zero detected rather than a stop bit
PF — Parity Error Flag
Indicates if received data’s parity matches parity bit. This feature is
active only when parity is enabled. The type of parity tested for is
determined by the PT (parity type) bit in SCxCR1.
0 = Parity correct
1 = Incorrect parity detected
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
259
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Multiple Serial Interface
Bit 7
6
5
4
3
2
1
Bit 0
0I
0
0
0
0
0
0
RAF
0
0
0
0
0
0
0
0
RESET:
SC0SR2/SC1SR2 — SCI Status Register 2
$00C5/$00CD
Read anytime. Write has no meaning or effect.
RAF — Receiver Active Flag
This bit is controlled by the receiver front end. It is set during the RT1
time period of the start bit search. It is cleared when an idle state is
detected or when the receiver circuitry detects a false start bit
(generally due to noise or baud rate mismatch).
0 = A character is not being received
1 = A character is being received
If enabled with RIE = 1, RAF set generates an interrupt when
VDDPLL is high while in WAIT mode.
Bit 7
6
5
4
3
2
1
Bit 0
R8
T8
0
0
0
0
0
0
—
—
—
—
—
—
—
—
RESET:
SC0DRH/SC1DRH — SCI Data Register High
$00C6/$00CE
Bit 7
6
5
4
3
2
1
Bit 0
R7/T7
R6/T6
R5/T5
R4/T4
R3/T3
R2/T2
R1/T1
R0/T0
—
—
—
—
—
—
—
—
RESET:
SC0DRL/SC1DRL — SCI Data Register Low
$00C7/$00CF
Bit 7
6
5
4
3
2
1
Bit 0
R8
T8
0
0
0
0
0
0
—
—
—
—
—
—
—
—
RESET:
SC0DRH/SC1DRH — SCI Data Register High
Technical Data
260
$00C6/$00CE
MC68HC912DG128 — Rev 3.0
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Multiple Serial Interface
Serial Communication Interface (SCI)
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
R7/T7
R6/T6
R5/T5
R4/T4
R3/T3
R2/T2
R1/T1
R0/T0
—
—
—
—
—
—
—
—
SC0DRL/SC1DRL — SCI Data Register Low
$00C7/$00CF
R8 — Receive Bit 8
Read anytime. Write has no meaning or affect.
Freescale Semiconductor, Inc...
This bit is the ninth serial data bit received when the SCI system is
configured for nine-data-bit operation.
T8 — Transmit Bit 8
Read or write anytime.
This bit is the ninth serial data bit transmitted when the SCI system is
configured for nine-data-bit operation. When using 9-bit data format
this bit does not have to be written for each data word. The same
value will be transmitted as the ninth bit until this bit is rewritten.
R7/T7–R0/T0 — Receive/Transmit Data Bits 7 to 0
Reads access the eight bits of the read-only SCI receive data register
(RDR). Writes access the eight bits of the write-only SCI transmit data
register (TDR). SCxDRL:SCxDRH form the 9-bit data word for the
SCI. If the SCI is being used with a 7- or 8-bit data word, only SCxDRL
needs to be accessed. If a 9-bit format is used, the upper register
should be written first to ensure that it is transferred to the transmitter
shift register with the lower register.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
261
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Multiple Serial Interface
14.5 Serial Peripheral Interface (SPI)
The serial peripheral interface allows the MC68HC912DG128 to
communicate synchronously with peripheral devices and other
microprocessors. The SPI system in the MC68HC912DG128 can
operate as a master or as a slave. The SPI is also capable of
interprocessor communications in a multiple master system.
When the SPI is enabled, all pins that are defined by the configuration
as inputs will be inputs regardless of the state of the DDRS bits for those
pins. All pins that are defined as SPI outputs will be outputs only if the
DDRS bits for those pins are set. Any SPI output whose corresponding
DDRS bit is cleared can be used as a general-purpose input.
A bidirectional serial pin is possible using the DDRS as the direction
control.
14.5.1 SPI Baud Rate Generation
The E Clock is input to a divider series and the resulting SPI clock rate
may be selected to be E divided by 2, 4, 8, 16, 32, 64, 128 or 256. Three
bits in the SP0BR register control the SPI clock rate. This baud rate
generator is activated only when SPI is in the master mode and serial
transfer is taking place. Otherwise this divider is disabled to save power.
14.5.2 SPI Operation
In the SPI system the 8-bit data register in the master and the 8-bit data
register in the slave are linked to form a distributed 16-bit register. When
a data transfer operation is performed, this 16-bit register is serially
shifted eight bit positions by the SCK clock from the master so the data
is effectively exchanged between the master and the slave. Data written
to the SP0DR register of the master becomes the output data for the
slave and data read from the SP0DR register of the master after a
transfer operation is the input data from the slave.
Technical Data
262
MC68HC912DG128 — Rev 3.0
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Multiple Serial Interface
Serial Peripheral Interface (SPI)
MCU P CLOCK
(SAME AS E RATE)
DIVIDER
÷2 ÷4 ÷8 ÷16 ÷32 ÷64 ÷128 ÷256
8-BIT SHIFT REGISTER
S
M
MISO
PS4
M
S
MOSI
PS5
READ DATA BUFFER
SP0DR SPI DATA REGISTER
SELECT
LSBF
PIN
CONTROL
LOGIC
SPR0
SPR1
SPR2
SHIFT CONTROL LOGIC
CLOCK
SCK
PS6
S
CLOCK
LOGIC
SP0BR SPI BAUD RATE REGISTER
M
SS
PS7
MSTR
SPE
SPI CONTROL
SPI
INTERRUPT
REQUEST
SP0SR SPI STATUS REGISTER
SP0CR1 SPI CONTROL REGISTER 1
SPC0
RDS
PUPS
SSOE
LSBF
CPHA
CPOL
SWOM
MSTR
SPE
SPIE
MODF
WCOL
SWOM
SPIF
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
SP0CR2 SPI CONTROL REGISTER 2
INTERNAL BUS
Figure 14-3. Serial Peripheral Interface Block Diagram
A clock phase control bit (CPHA) and a clock polarity control bit (CPOL)
in the SP0CR1 register select one of four possible clock formats to be
used by the SPI system. The CPOL bit simply selects non-inverted or
inverted clock. The CPHA bit is used to accommodate two
fundamentally different protocols by shifting the clock by one half cycle
or no phase shift.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
263
Freescale Semiconductor, Inc.
Multiple Serial Interface
Transfer
Begin
End
SCK (CPOL=0)
SCK (CPOL=1)
If next transfer begins here
Freescale Semiconductor, Inc...
SAMPLE I
(MOSI/MISO)
CHANGE O
(MOSI pin)
CHANGE O
(MISO pin)
SEL SS (O)
(Master only)
SEL SS (I)
MSB first (LSBF=0):
LSB first (LSBF=1):
tL
MSB
LSB
Bit 6
Bit 1
Bit 5
Bit 2
Bit 4
Bit 3
Bit 3
Bit 4
Bit 2
Bit 5
Bit 1
Bit 6
LSB
MSB
tI
tT
tL
Minimum 1/2 SCK
for tT, tl, tL
Figure 14-4. SPI Clock Format 0 (CPHA = 0)
Technical Data
264
MC68HC912DG128 — Rev 3.0
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Multiple Serial Interface
Serial Peripheral Interface (SPI)
Transfer
Begin
End
SCK (CPOL=0)
SCK (CPOL=1)
SAMPLE I
(MOSI/MISO)
If next transfer begins here
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
CHANGE O
(MOSI pin)
CHANGE O
(MISO pin)
SEL SS (O)
(Master only)
SEL SS (I)
tL
MSB first (LSBF=0):
LSB first (LSBF=1):
MSB
LSB
Bit 6
Bit 1
Bit 5
Bit 2
Bit 4
Bit 3
Bit 3
Bit 4
Bit 2
Bit 5
Bit 1
Bit 6
tI
tT
tL
LSB Minimum 1/2 SCK
for tT, tl, tL
MSB
Figure 14-5. SPI Clock Format 1 (CPHA = 1)
14.5.3 SS Output
Available in master mode only, SS output is enabled with the SSOE bit
in the SP0CR1 register if the corresponding DDRS is set. The SS output
pin will be connected to the SS input pin of the external slave device. The
SS output automatically goes low for each transmission to select the
external device and it goes high during each idling state to deselect
external devices.
Table 14-3. SS Output Selection
DDS7
0
0
1
1
SSOE
0
1
0
1
Master Mode
SS Input with MODF Feature
Reserved
General-Purpose Output
SS Output
MC68HC912DG128 — Rev 3.0
MOTOROLA
Slave Mode
SS Input
SS Input
SS Input
SS Input
Technical Data
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
265
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Multiple Serial Interface
14.5.4 Bidirectional Mode (MOMI or SISO)
In bidirectional mode, the SPI uses only one serial data pin for external
device interface. The MSTR bit decides which pin to be used. The MOSI
pin becomes serial data I/O (MOMI) pin for the master mode, and the
MISO pin becomes serial data I/O (SISO) pin for the slave mode. The
direction of each serial I/O pin depends on the corresponding DDRS bit.
When SPE=1
Master Mode
MSTR=1
Slave Mode
MSTR=0
MO
Serial Out
SPI
Normal
Mode
SPC0=0
SPI
DDRS5
Serial In
MI
Serial Out
Serial Out
MO
Serial In
SPI
SPI
DDS5
MI
Serial In
SWOM enables open drain output.
SPI
Bidirectional
Mode
SPC0=1
SI
DDS4
SO
SPI
DDRS5
Serial Out
Serial Out
MOMI
Serial In
SPI
DDS5
PS4
SWOM enables open drain output. PS4 becomes GPIO.
PS5
Serial In
PS4
Serial In
SO
Serial Out
Serial In
SPI
DDRS4
SWOM enables open drain output.
MOMI
Serial Out
SI
Serial In
DDRS4
SISO
PS5
DDS4
SISO
Serial Out
SWOM enables open drain output. PS5 becomes GPIO.
Figure 14-6. Normal Mode and Bidirectional Mode
Technical Data
266
MC68HC912DG128 — Rev 3.0
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Multiple Serial Interface
Serial Peripheral Interface (SPI)
14.5.5 Register Descriptions
Control and data registers for the SPI subsystem are described below.
The memory address indicated for each register is the default address
that is in use after reset. For more information refer to Operating Modes.
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
SPIE
SPE
SWOM
MSTR
CPOL
CPHA
SSOE
LSBF
0
0
0
0
0
1
0
0
SP0CR1 — SPI Control Register 1
$00D0
Read or write anytime.
SPIE — SPI Interrupt Enable
0 = SPI interrupts are inhibited
1 = Hardware interrupt sequence is requested each time the SPIF
or MODF status flag is set
SPE — SPI System Enable
0 = SPI internal hardware is initialized and SPI system is in a lowpower disabled state.
1 = PS[4:7] are dedicated to the SPI function
When MODF is set, SPE always reads zero. SP0CR1 must be written
as part of a mode fault recovery sequence.
SWOM — Port S Wired-OR Mode
Controls not only SPI output pins but also the general-purpose output
pins (PS[4:7]) which are not used by SPI.
0 = SPI and/or PS[4:7] output buffers operate normally
1 = SPI and/or PS[4:7] output buffers behave as open-drain
outputs
MSTR — SPI Master/Slave Mode Select
0 = Slave mode
1 = Master mode
When MODF is set, MSTR always reads zero. SP0CR1 must be
written as part of a mode fault recovery sequence.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
267
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Multiple Serial Interface
CPOL, CPHA — SPI Clock Polarity, Clock Phase
These two bits are used to specify the clock format to be used in SPI
operations. When the clock polarity bit is cleared and data is not being
transferred, the SCK pin of the master device is low. When CPOL is
set, SCK idles high. See Figure 14-4 and Figure 14-5.
SSOE — Slave Select Output Enable
The SS output feature is enabled only in the master mode by
asserting the SSOE and DDS7.
LSBF — SPI LSB First enable
0 = Data is transferred most significant bit first
1 = Data is transferred least significant bit first
Normally data is transferred most significant bit first.This bit does not
affect the position of the MSB and LSB in the data register. Reads and
writes of the data register will always have MSB in bit 7.
SP0CR2 — SPI Control Register 2
RESET:
Bit 7
0
0
6
0
0
$00D1
5
0
0
4
0
0
3
PUPS
1
2
RDPS
0
1
SPSWAI
0
Bit 0
SPC0
0
Read or write anytime.
PUPS — Pull-Up Port S Enable
0 = No internal pull-ups on port S
1 = All port S input pins have an active pull-up device. If a pin is
programmed as output, the pull-up device becomes inactive
RDPS — Reduce Drive of Port S
0 = Port S output drivers operate normally
1 = All port S output pins have reduced drive capability for lower
power and less noise
SPSWAI — Serial Interface Stop in WAIT mode
0 = Serial interface clock operates normally
1 = Halt serial interface clock generation in WAIT mode
Technical Data
268
MC68HC912DG128 — Rev 3.0
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Multiple Serial Interface
Serial Peripheral Interface (SPI)
SPC0 — Serial Pin Control 0
This bit decides serial pin configurations with MSTR control bit.
SPC0(1)
Pin Mode
MSTR
MISO(2)
MOSI(3)
SCK(4)
SS(5)
0
Slave Out
Slave In
SCK In
SS In
1
Master In
Master Out
SCK Out
SS I/O
0
Slave I/O
GPI/O
SCK In
SS In
1
GPI/O
Master I/O
SCK Out
SS I/O
#1
Normal
0
#2
#3
Bidirectional
1
#4
1. The serial pin control 0 bit enables bidirectional configurations.
2. Slave output is enabled if DDS4 = 1, SS = 0 and MSTR = 0. (#1, #3)
3. Master output is enabled if DDS5 = 1 and MSTR = 1. (#2, #4)
4. SCK output is enabled if DDS6 = 1 and MSTR = 1. (#2, #4)
5. SS output is enabled if DDS7 = 1, SSOE = 1 and MSTR = 1. (#2, #4)
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
SPR2
SPR1
SPR0
0
0
0
0
0
0
0
0
SP0BR — SPI Baud Rate Register
$00D2
Read anytime. Write anytime.
At reset, E Clock divided by 2 is selected.
SPR[2:0] — SPI Clock (SCK) Rate Select Bits
These bits are used to specify the SPI clock rate.
Table 14-4. SPI Clock Rate Selection
SPR2
SPR1
SPR0
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
E Clock
Divisor
2
4
8
16
32
64
128
256
Frequency at
Frequency at
E Clock = 4 MHz E Clock = 8 MHz
2.0 MHz
4.0 MHz
1.0 MHz
2.0 MHz
500 kHz
1.0 MHz
250 kHz
500 KHz
125 kHz
250 KHz
62.5 kHz
125 KHz
31.3 kHz
62.5 KHz
15.6 kHz
31.3 KHz
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
269
Freescale Semiconductor, Inc.
Multiple Serial Interface
Bit 7
6
5
4
3
2
1
Bit 0
SPIF
WCOL
0
MODF
0
0
0
0
0
0
0
0
0
0
0
0
RESET:
SP0SR — SPI Status Register
$00D3
Read anytime. Write has no meaning or effect.
Freescale Semiconductor, Inc...
SPIF — SPI Interrupt Request
SPIF is set after the eighth SCK cycle in a data transfer and it is
cleared by reading the SP0SR register (with SPIF set) followed by an
access (read or write) to the SPI data register.
WCOL — Write Collision Status Flag
The MCU write is disabled to avoid writing over the data being
transferred. No interrupt is generated because the error status flag
can be read upon completion of the transfer that was in progress at
the time of the error. Automatically cleared by a read of the SP0SR
(with WCOL set) followed by an access (read or write) to the SP0DR
register.
0 = No write collision
1 = Indicates that a serial transfer was in progress when the MCU
tried to write new data into the SP0DR data register.
MODF — SPI Mode Error Interrupt Status Flag
This bit is set automatically by SPI hardware if the MSTR control bit is
set and the slave select input pin becomes zero. This condition is not
permitted in normal operation. In the case where DDRS bit 7 is set,
the PS7 pin is a general-purpose output pin or SS output pin rather
than being dedicated as the SS input for the SPI system. In this
special case the mode fault function is inhibited and MODF remains
cleared. This flag is automatically cleared by a read of the SP0SR
(with MODF set) followed by a write to the SP0CR1 register.
Technical Data
270
MC68HC912DG128 — Rev 3.0
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Multiple Serial Interface
Port S
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
6
5
4
3
2
1
Bit 0
SP0DR — SPI Data Register
$00D5
Read anytime (normally only after SPIF flag set). Write anytime (see
WCOL write collision flag).
Reset does not affect this address.
This 8-bit register is both the input and output register for SPI data.
Reads of this register are double buffered but writes cause data to be
written directly into the serial shifter. In the SPI system the 8-bit data
register in the master and the 8-bit data register in the slave are linked
by the MOSI and MISO wires to form a distributed 16-bit register. When
a data transfer operation is performed, this 16-bit register is serially
shifted eight bit positions by the SCK clock from the master so the data
is effectively exchanged between the master and the slave. Note that
some slave devices are very simple and either accept data from the
master without returning data to the master or pass data to the master
without requiring data from the master.
14.6 Port S
In all modes, port S bits PS[7:0] can be used for either general-purpose
I/O, or with the SCI and SPI subsystems. During reset, port S pins are
configured as high-impedance inputs (DDRS is cleared).
PORTS — Port S Data Register
Bit 7
Pin
Function
6
$00D6
5
4
3
2
1
Bit 0
PS7
PS6
PS5
PS4
PS3
PS2
PS1
PS0
SS
CS
SCK
MOSI
MOMI
MISO
SISO
TXD1
RXD1
TXD0
RXD0
Read anytime (inputs return pin level; outputs return pin driver input
level). Write data stored in internal latch (drives pins only if configured for
output). Writes do not change pin state when pin configured for SPI or
SCI output.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
271
Freescale Semiconductor, Inc.
Multiple Serial Interface
After reset all bits are configured as general-purpose inputs.
Port S shares function with the on-chip serial systems (SPI and SCI0/1).
Bit 7
6
5
4
3
2
1
Bit 0
DDS7
DDS6
DDS5
DDS4
DDS3
DDS2
DDS1
DDS0
0
0
0
0
0
0
0
0
RESET:
DDRS — Data Direction Register for Port S
$00D7
Freescale Semiconductor, Inc...
Read or write anytime.
After reset, all general-purpose I/O are configured for input only.
0 = Configure the corresponding I/O pin for input only
1 = Configure the corresponding I/O pin for output
DDS2, DDS0 — Data Direction for Port S Bit 2 and Bit 0
If the SCI receiver is configured for two-wire SCI operation,
corresponding port S pins will be input regardless of the state of these
bits.
DDS3, DDS1 — Data Direction for Port S Bit 3 and Bit 1
If the SCI transmitter is configured for two-wire SCI operation,
corresponding port S pins will be output regardless of the state of
these bits.
DDS[6:4] — Data Direction for Port S Bits 6 through 4
If the SPI is enabled and expects the corresponding port S pin to be
an input, it will be an input regardless of the state of the DDRS bit. If
the SPI is enabled and expects the bit to be an output, it will be an
output ONLY if the DDRS bit is set.
DDS7 — Data Direction for Port S Bit 7
In SPI slave mode, DDRS7 has no meaning or effect; the PS7 pin is
dedicated as the SS input. In SPI master mode, DDRS7 determines
whether PS7 is an error detect input to the SPI or a general-purpose
or slave select output line.
NOTE:
If mode fault error occurs, bits 5, 6 and 7 are forced to zero. .
Technical Data
272
MC68HC912DG128 — Rev 3.0
Multiple Serial Interface
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Section 15. Inter-IC Bus
15.1 Contents
15.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 273
15.3
IIC Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 274
15.4
IIC System Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
15.5
IIC Protocol . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 276
15.6
IIC Register Descriptions . . . . . . . . . . . . . . . . . . . . . . . . . . . . 281
15.7
IIC Programming Examples . . . . . . . . . . . . . . . . . . . . . . . . . .290
15.2 Introduction
The Inter-IC Bus (IIC or I2C) is a two-wire, bidirectional serial bus that
provides a simple, efficient method of data exchange between devices.
Being a two-wire device, the IIC minimizes the need for large numbers
of connections between devices, and eliminates the need for an address
decoder.
This bus is suitable for applications requiring occasional
communications over a short distance between a number of devices. It
also provides flexibility, allowing additional devices to be connected to
the bus for further expansion and system development.
The interface is designed to operate up to 100kbps with maximum bus
loading and timing. The device is capable of operating at higher baud
rates, up to a maximum of clock/20, with reduced bus loading. The
maximum communication length and the number of devices that can be
connected are limited by a maximum bus capacitance of 400pF.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
273
Freescale Semiconductor, Inc.
Inter-IC Bus
15.3 IIC Features
Freescale Semiconductor, Inc...
The IIC module has the following key features:
•
Compatible with I2C Bus standard
•
Multi-master operation
•
Software programmable for one of 64 different serial clock
frequencies
•
Software selectable acknowledge bit
•
Interrupt driven byte-by-byte data transfer
•
Arbitration lost interrupt with automatic mode switching from
master to slave
•
Calling address identification interrupt
•
Start and stop signal generation/detection
•
Repeated start signal generation
•
Acknowledge bit generation/detection
•
Bus busy detection
•
Eight-bit general purpose I/O port
A block diagram of the IIC module is shown in Figure 15-1.
Technical Data
274
MC68HC912DG128 — Rev 3.0
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Inter-IC Bus
IIC Features
ADDR & CONTROL
DATA
INTERRUPT
Freescale Semiconductor, Inc...
ADDR_DECODE
CTRL_REG
DATA_MUX
FREQ_REG
ADDR_REG
STATUS_REG
DATA_REG
In/Out
Input
Data
Sync
Shift
Start,
Register
Stop &
Arbitration
Control
Clock
Control
Address
Compare
SCL
SDA
Figure 15-1. IIC Block Diagram
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
275
Freescale Semiconductor, Inc.
Inter-IC Bus
15.4 IIC System Configuration
The IIC system uses a Serial Data line (SDA) and a Serial Clock Line
(SCL) for data transfer. All devices connected to it must have open drain
or open collector outputs. Logic “and” function is exercised on both lines
with external pull-up resistors, the value of these resistors is system
dependent.
Freescale Semiconductor, Inc...
15.5 IIC Protocol
Normally, a standard communication is composed of four parts: START
signal, slave address transmission, data transfer and STOP signal. They
are described briefly in the following sections and illustrated in Figure 152.
MSB
SCL
SDA
1
LSB
2
3
4
5
6
7
Calling Address
Read/
Write
MSB
SDA
Start
Signal
MSB
9
AD7 AD6 AD5 AD4 AD3 AD2 AD1 R/W
Start
Signal
SCL
8
1
XXX
3
4
5
6
7
8
Read/
Write
3
4
5
6
7
8
D7
D6
D5
D4
D3
D2
D1
D0
Data Byte
1
XX
Ack
Bit
Repeated
Start
Signal
9
No
Ack
Bit
MSB
9
AD7 AD6 AD5 AD4 AD3 AD2 AD1 R/W
Calling Address
2
Ack
Bit
LSB
2
LSB
1
Stop
Signal
LSB
2
3
4
5
6
7
8
9
AD7 AD6 AD5 AD4 AD3 AD2 AD1 R/W
New Calling Address
Read/
Write
No
Ack
Bit
Stop
Signal
Figure 15-2. IIC Transmission Signals
Technical Data
276
MC68HC912DG128 — Rev 3.0
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Inter-IC Bus
IIC Protocol
15.5.1 START Signal
When the bus is free, i.e. no master device is engaging the bus (both
SCL and SDA lines are at logical high), a master may initiate
communication by sending a START signal. As shown in Figure 15-2, a
START signal is defined as a high-to-low transition of SDA while SCL is
high. This signal denotes the beginning of a new data transfer (each data
transfer may contain several bytes of data) and wakes up all slaves.
15.5.2 Slave Address Transmission
The first byte of data transfer immediately after the START signal is the
slave address transmitted by the master. This is a seven-bit calling
address followed by a R/W bit. The R/W bit tells the slave the desired
direction of data transfer.
1 = Read transfer, the slave transmits data to the master.
0 = Write transfer, the master transmits data to the slave.
Only the slave with a calling address that matches the one transmitted
by the master will respond by sending back an acknowledge bit. This is
done by pulling the SDA low at the 9th clock (see Figure 15-2).
Slave address - No two slaves in the system may have the same
address. If the IIC is master, it must not transmit an address that
is equal to its own slave address. The IIC cannot be master and
slave at the same time. If however arbitration is lost during an
address cycle the IIC will revert to slave mode and operate
correctly even if it is being addressed by another master.
15.5.3 Data Transfer
Once successful slave addressing is achieved, the data transfer can
proceed byte-by-byte in a direction specified by the R/W bit sent by the
calling master.
NOTE:
All transfers that come after an address cycle are referred to as data
transfers, even if they carry sub-address information for the slave
device.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
277
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Inter-IC Bus
Each data byte is 8 bits long. Data may be changed only while SCL is low
and must be held stable while SCL is high as shown in Figure 15-2. There
is one clock pulse on SCL for each data bit, the MSB being transferred
first. Each data byte has to be followed by an acknowledge bit, which is
signalled from the receiving device by pulling the SDA low at the ninth
clock. So one complete data byte transfer needs nine clock pulses.
If the slave receiver does not acknowledge the master, the SDA line
must be left high by the slave. The master can then generate a stop
signal to abort the data transfer or a start signal (repeated start) to
commence a new calling.
If the master receiver does not acknowledge the slave transmitter after
a byte transmission, it means ’end of data’ to the slave, so the slave
releases the SDA line for the master to generate STOP or START signal.
15.5.4 STOP Signal
The master can terminate the communication by generating a STOP
signal to free the bus. However, the master may generate a START
signal followed by a calling command without generating a STOP signal
first. This is called repeated START. A STOP signal is defined as a lowto-high transition of SDA while SCL at logical “1” (see Figure 15-2).
The master can generate a STOP even if the slave has generated an
acknowledge at which point the slave must release the bus.
15.5.5 Repeated START Signal
As shown in Figure 15-2, a repeated START signal is a START signal
generated without first generating a STOP signal to terminate the
communication. This is used by the master to communicate with another
slave or with the same slave in different mode (transmit/receive mode)
without releasing the bus.
Technical Data
278
MC68HC912DG128 — Rev 3.0
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Inter-IC Bus
IIC Protocol
15.5.6 Arbitration Procedure
IIC is a true multi-master bus that allows more than one master to be
connected on it. If two or more masters try to control the bus at the same
time, a clock synchronization procedure determines the bus clock, for
which the low period is equal to the longest clock low period and the high
is equal to the shortest one among the masters. The relative priority of
the contending masters is determined by a data arbitration procedure, a
bus master loses arbitration if it transmits logic “1” while another master
transmits logic “0”. The losing masters immediately switch over to slave
receive mode and stop driving SDA output. In this case the transition
from master to slave mode does not generate a STOP condition.
Meanwhile, a status bit is set by hardware to indicate loss of arbitration.
15.5.7 Clock Synchronization
Since wire-AND logic is performed on SCL line, a high-to-low transition
on SCL line affects all the devices connected on the bus. The devices
start counting their low period and once a device’s clock has gone low, it
holds the SCL line low until the clock high state is reached. However, the
change of low to high in this device clock may not change the state of the
SCL line if another device clock is still within its low period. Therefore,
synchronized clock SCL is held low by the device with the longest low
period. Devices with shorter low periods enter a high wait state during this
time (see Figure 15-3). When all devices concerned have counted off
their low period, the synchronized clock SCL line is released and pulled
high. There is then no difference between the device clocks and the state
of the SCL line and all the devices start counting their high periods. The
first device to complete its high period pulls the SCL line low again.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
279
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Inter-IC Bus
WAIT
Start Counting High Period
SCL1
SCL2
SCL
Internal Counter Reset
Figure 15-3. IIC Clock Synchronization
15.5.8 Handshaking
The clock synchronization mechanism can be used as a handshake in
data transfer. Slave devices may hold the SCL low after completion of
one byte transfer (9 bits). In such case, it halts the bus clock and forces
the master clock into wait states until the slave releases the SCL line.
15.5.9 Clock Stretching
The clock synchronization mechanism can be used by slaves to slow
down the bit rate of a transfer. After the master has driven SCL low the
slave can drive SCL low for the required period and then release it. If the
slave SCL low period is greater than the master SCL low period then the
resulting SCL bus signal low period is stretched.
Technical Data
280
MC68HC912DG128 — Rev 3.0
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Inter-IC Bus
IIC Register Descriptions
15.6 IIC Register Descriptions
.
IBAD — IIC Bus Address Register
RESET:
Bit 7
ADR7
0
6
ADR6
0
$00E0
5
ADR5
0
4
ADR4
0
3
ADR3
0
2
ADR2
0
1
ADR1
0
Bit 0
0
0
Read and write anytime
This register contains the address the IIC will respond to when
addressed as a slave; note that it is not the address sent on the bus
during the address transfer
ADR7–ADR1 — Slave Address
Bit 1 to bit 7 contain the specific slave address to be used by the IIC
module.
The default mode of IIC is slave mode for an address match on the
bus.
IBFD — IIC Bus Frequency Divider Register
RESET:
Bit 7
0
0
6
0
0
5
IBC5
0
$00E1
4
IBC4
0
3
IBC3
0
2
IBC2
0
1
IBC1
0
Bit 0
IBC0
0
Read and write anytime
IBC5–IBC0 — IIC Bus Clock Rate 5–0
This field is used to prescale the clock for bit rate selection. The bit
clock generator is implemented as a prescaled shift register - IBC5-3
select the prescaler divider and IBC2-0 select the shift register tap
point. The IBC bits are decoded to give the Tap and Prescale values
as shown in Table 15-1.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
281
Freescale Semiconductor, Inc.
Inter-IC Bus
Freescale Semiconductor, Inc...
Table 15-1. IIC Tap and Prescale Values
IBC2-0
(bin)
SCL Tap
(clocks)
SDA Tap
(clocks)
IBC5-3
(bin)
scl2tap
(clocks)
tap2tap
(clocks)
000
5
1
000
4
1
001
6
1
001
4
2
010
7
2
010
6
4
011
8
2
011
6
8
100
9
3
100
14
16
101
10
3
101
30
32
110
12
4
110
62
64
111
15
4
111
126
128
The number of clocks from the falling edge of SCL to the first tap
(Tap[1]) is defined by the values shown in the scl2tap column of Table
15-1, all subsequent tap points are separated by 2IBC5-3 as shown in
the tap2tap column in Table 15-1. The SCL Tap is used to generated
the SCL period and the SDA Tap is used to determine the delay from
the falling edge of SCL to SDA changing, the SDA hold time.
The serial bit clock frequency is equal to the CPU clock frequency
divided by the divider shown in Table 15-2. The equation used to
generate the divider values from the IBFD bits is:
SCL Divider = 2 x ( scl2tap + [ ( SCL_Tap -1 ) x tap2tap ] + 2 )
The SDA hold delay is equal to the CPU clock period multiplied by the
SDA Hold value shown in Figure 15-2. The equation used to generate
the SDA Hold value from the IBFD bits is:
SDA Hold = scl2tap + [ ( SDA_Tap - 1 ) x tap2tap ] + 3
Technical Data
282
MC68HC912DG128 — Rev 3.0
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Inter-IC Bus
IIC Register Descriptions
Table 15-2. IIC Divider and SDA Hold values
SCL Divider
(clocks)
SDA Hold
(clocks)
IBC5-0
(hex)
SCL Divider
(clocks)
SDA Hold
(clocks)
00
20
7
20
160
17
01
22
7
21
192
17
02
24
8
22
224
33
03
26
8
23
256
33
04
28
9
24
288
49
05
30
9
25
320
49
06
34
10
26
384
65
07
40
10
27
480
65
08
28
7
28
320
33
09
32
7
29
384
33
0A
36
9
2A
448
65
0B
40
9
2B
512
65
0C
44
11
2C
576
97
0D
48
11
2D
640
97
0E
56
13
2E
768
129
0F
68
13
2F
960
129
10
48
9
30
640
65
11
56
9
31
768
65
12
64
13
32
896
129
13
72
13
33
1024
129
14
80
17
34
1152
193
15
88
17
35
1280
193
16
104
21
36
1536
257
17
128
21
37
1920
257
18
80
9
38
1280
129
19
96
9
39
1536
129
1A
112
17
3A
1792
257
Freescale Semiconductor, Inc...
IBC5-0
(hex)
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
283
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Inter-IC Bus
Table 15-2. IIC Divider and SDA Hold values
IBC5-0
(hex)
SCL Divider
(clocks)
SDA Hold
(clocks)
IBC5-0
(hex)
SCL Divider
(clocks)
SDA Hold
(clocks)
1B
128
17
3B
2048
257
1C
144
25
3C
2304
385
1D
160
25
3D
2560
385
1E
192
33
3E
3072
513
1F
240
33
3F
3840
513
IBCR — IIC Bus Control Register
RESET:
Bit 7
IBEN
0
6
IBIE
0
$00E2
5
MS/SL
0
4
Tx/Rx
0
3
TXAK
0
2
RSTA
0
1
0
0
Bit 0
IBSWAI
0
Read and write anytime
IBEN — IIC Bus Enable
This bit controls the software reset of the entire IIC module.
0 = The module is reset and disabled. This is the power-on reset
situation. When low the IIC system is held in reset but registers
can still be accessed.
1 = The IIC system is enabled. This bit must be set before any other
IBCR bits have any effect.
If the IIC module is enabled in the middle of a byte transfer the
interface behaves as follows: slave mode ignores the current transfer
on the bus and starts operating whenever a subsequent start
condition is detected. Master mode will not be aware that the bus is
busy, hence if a start cycle is initiated then the current bus cycle may
become corrupt. This would ultimately result in either the current bus
master or the IIC module losing arbitration, after which bus operation
would return to normal.
IBIE — IIC Bus Interrupt Enable
0 = Interrupts from the IIC module are disabled. Note that this does
not clear any currently pending interrupt condition.
1 = Interrupts from the IIC module are enabled. An IIC interrupt
occurs provided the IBIF bit in the status register is also set.
Technical Data
284
MC68HC912DG128 — Rev 3.0
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Inter-IC Bus
IIC Register Descriptions
MS/SL — Master/Slave mode select bit
Freescale Semiconductor, Inc...
Upon reset, this bit is cleared. When this bit is changed from 0 to 1, a
START signal is generated on the bus, and the master mode is
selected. When this bit is changed from 1 to 0, a STOP signal is
generated and the operation mode changes from master to slave.
MS/SL is cleared without generating a STOP signal when the master
loses arbitration.
0 = Slave Mode
1 = Master Mode
Tx/Rx — Transmit/Receive mode select bit
This bit selects the direction of master and slave transfers. When
addressed as a slave this bit should be set by software according to
the SRW bit in the status register. In master mode this bit should be
set according to the type of transfer required. Therefore, for address
cycles, this bit will always be high.
0 = Receive
1 = Transmit
TXAK — Transmit Acknowledge enable
This bit specifies the value driven onto SDA during acknowledge
cycles for both master and slave receivers. Note that values written to
this bit are only used when the IIC is a receiver, not a transmitter.
0 = An acknowledge signal will be sent out to the bus at the 9th
clock bit after receiving one byte data
1 = No acknowledge signal response is sent (i.e., acknowledge bit
= 1)
RSTA — Repeat Start
Writing a 1 to this bit will generate a repeated START condition on the
bus, provided it is the current bus master. This bit will always be read
as a low. Attempting a repeated start at the wrong time, if the bus is
owned by another master, will result in loss of arbitration.
1 = Generate repeat start cycle
IBSWAI — IIC Stop in WAIT mode
0 = IIC module operates normally
1 = Halt clock generation of IIC module in WAIT mode
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
285
Freescale Semiconductor, Inc.
Inter-IC Bus
IBSR — IIC Bus Status Register
RESET:
Bit 7
TCF
1
6
IAAS
0
$00E3
5
IBB
0
4
IBAL
0
3
0
0
2
SRW
0
1
IBIF
0
Bit 0
RXAK
0
This status register is read-only with exception of bit 1 (IBIF) and bit 4
(IBAL), which are software clearable
TCF — Data transferring bit
Freescale Semiconductor, Inc...
While one byte of data is being transferred, this bit is cleared. It is set
by the falling edge of the 9th clock of a byte transfer.
0 = Transfer in progress
1 = Transfer complete
IAAS — Addressed as a slave bit
When its own specific address (IIC Bus Address Register) is matched
with the calling address, this bit is set. The CPU is interrupted
provided the IBIE is set. Then the CPU needs to check the SRW bit
and set its Tx/Rx mode accordingly. Writing to the IIC Bus Control
Register clears this bit.
0 = Not addressed
1 = Addressed as a slave
IBB — IIC Bus busy bit
This bit indicates the status of the bus. When a START signal is
detected, the IBB is set. If a STOP signal is detected, it is cleared.
0 = Bus is idle
1 = Bus is busy
IBAL — Arbitration Lost
The arbitration lost bit (IBAL) is set by hardware when the arbitration
procedure is lost. Arbitration is lost in the following circumstances:
1. SDA sampled as low when the master drives a high during an
address or data transmit cycle.
2. SDA sampled as a low when the master drives a high during the
acknowledge bit of a data receive cycle.
3. A start cycle is attempted when the bus is busy.
4. A repeated start cycle is requested in slave mode.
Technical Data
286
MC68HC912DG128 — Rev 3.0
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Inter-IC Bus
IIC Register Descriptions
5. A stop condition is detected when the master did not request it.
This bit must be cleared by software, by writing a one to it.
SRW — Slave Read/Write
When IAAS is set this bit indicates the value of the R/W command bit
of the calling address sent from the master.
Freescale Semiconductor, Inc...
CAUTION:
This bit is only valid when the IIC is in slave mode, a complete address
transfer has occurred with an address match and no other transfers have
been initiated.
Checking this bit, the CPU can select slave transmit/receive mode
according to the command of the master.
0 = Slave receive, master writing to slave
1 = Slave transmit, master reading from slave
IBIF — IIC Bus Interrupt Flag
The IBIF bit is set when an interrupt is pending, which will cause a
processor interrupt request provided IBIE is set. IBIF is set when one
of the following events occurs:
1. Complete one byte transfer (set at the falling edge of the 9th
clock).
2. Receive a calling address that matches its own specific address in
slave receive mode.
3. Arbitration lost.
This bit must be cleared by software, writing a one to it, in the interrupt
routine.
RXAK — Received Acknowledge
The value of SDA during the acknowledge bit of a bus cycle. If the
received acknowledge bit (RXAK) is low, it indicates an acknowledge
signal has been received after the completion of 8 bits data
transmission on the bus. If RXAK is high, it means no acknowledge
signal is detected at the 9th clock.
0 = Acknowledge received
1 = No acknowledge received
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
287
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Inter-IC Bus
.
IBDR — IIC Bus Data I/O Register
RESET:
Bit 7
D7
0
6
D6
0
$00E4
5
D5
0
4
D4
0
3
D3
0
2
D2
0
1
D1
0
Bit 0
D0
0
High
Read and write anytime
In master transmit mode, when data is written to the IBDR a data transfer
is initiated. The most significant bit is sent first. In master receive mode,
reading this register initiates next byte data receiving. In slave mode, the
same functions are available after an address match has occurred.
NOTE:
In master transmit mode, the first byte of data written to IBDR following
assertion of MS/SL is used for the address transfer and should comprise
of the calling address (in position D7-D1) concatenated with the required
R/W bit (in position D0).
IBPURD — Pull-Up and Reduced Drive for Port IB
RESET:
Bit 7
0
0
6
0
0
5
0
0
$00E5
4
RDPIB
0
3
0
0
2
0
0
1
0
0
Bit 0
PUPIB
0
Read and write anytime
RDPIB — Reduced Drive of Port IB
0 = All port IB output pins have full drive enabled.
1 = All port IB output pins have reduced drive capability.
PUPIB — Pull-Up Port IB Enable
0 = Port IB pull-ups are disabled.
1 = Enable pull-up devices for port IB input pins [7:4]. Pull-ups for
port IB input pins [3:0] are always enabled.
Technical Data
288
MC68HC912DG128 — Rev 3.0
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Inter-IC Bus
IIC Register Descriptions
PORTIB — Port Data IB Register
IIC
RESET:
Bit 7
PIB7
SCL
-
$00E6
6
PIB6
SDA
-
5
PIB5
-
4
PIB4
-
3
PIB3
-
2
PIB2
-
1
PIB1
-
Bit 0
PIB0
-
Read and write anytime.
IIC functions SCL and SDA share port IB pins 7 and 6 and take
precedence over the general-purpose port when IIC is enabled. The
SCL and SDA output buffers behave as open-drain outputs.
When port is configured as input, a read will return the pin level. Port bits
3-0 have internal pull ups when configured as inputs so they will read ones.
When configured as output, a read will return the latched output data.
Port bits 5 through 0 will read the last value written. A write will drive
associated pins only if configured for output and IIC is not enabled.
Port bits 3-0 do not have available external pins.
DDRIB — Data Direction for Port IB Register
RESET:
Bit 7
DDRIB7
0
6
DDRIB6
0
5
DDRIB5
0
$00E7
4
DDRIB4
0
3
DDRIB3
0
2
DDRIB2
0
1
DDRIB1
0
Bit 0
DDRIB0
0
Read and write anytime
DDRIB[7:4] — Port IB [7:4] Data direction
Each bit determines the primary direction for each pin configured as
general-purpose I/O.
0 = Associated pin is a high-impedance input.
1 = Associated pin is an output.
DDRIB[3:0] — These bits serve as memory locations since there are no
corresponding external port pins.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
289
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Inter-IC Bus
15.7 IIC Programming Examples
15.7.1 Initialization Sequence
Reset will put the IIC Bus Control Register to its default status. Before
the interface can be used to transfer serial data, an initialization
procedure must be carried out, as follows:
1. Update the Frequency Divider Register (IBFD) and select the
required division ratio to obtain SCL frequency from system clock.
2. Update the IIC Bus Address Register (IBAD) to define its slave
address.
3. Set the IBEN bit of the IIC Bus Control Register (IBCR) to enable
the IIC interface system.
4. Modify the bits of the IIC Bus Control Register (IBCR) to select
Master/Slave mode, Transmit/Receive mode and interrupt enable
or not.
15.7.2 Generation of START
After completion of the initialization procedure, serial data can be
transmitted by selecting the ’master transmitter’ mode. If the device is
connected to a multi-master bus system, the state of the IIC Bus Busy
bit (IBB) must be tested to check whether the serial bus is free.
If the bus is free (IBB=0), the start condition and the first byte (the slave
address) can be sent. The data written to the data register comprises the
slave calling address and the LSB set to indicate the direction of transfer
required from the slave.
The bus free time (i.e., the time between a STOP condition and the
following START condition) is built into the hardware that generates the
START cycle. Depending on the relative frequencies of the system clock
and the SCL period it may be necessary to wait until the IIC is busy after
writing the calling address to the IBDR before proceeding with the
following instructions. This is illustrated in the following example.
Technical Data
290
MC68HC912DG128 — Rev 3.0
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Inter-IC Bus
IIC Programming Examples
An example of a program which generates the START signal and
transmits the first byte of data (slave address) is shown below:
CHFLAG
TXSTART
IBFREE
BRSET
BSET
IBSR,#$20,*
IBCR,#$30
MOVB
CALLING,IBDR
BRCLR
IBSR,#$20,*
;WAIT FOR IBB FLAG TO CLEAR
;SET TRANSMIT AND MASTER MODE
;i.e. GENERATE START CONDITION
;TRANSMIT THE CALLING
;ADDRESS, D0=R/W
;WAIT FOR IBB FLAG TO SET
15.7.3 Post-Transfer Software Response
Transmission or reception of a byte will set the data transferring bit (TCF)
to 1, which indicates one byte communication is finished. The IIC Bus
interrupt bit (IBIF) is set also; an interrupt will be generated if the interrupt
function is enabled during initialization by setting the IBIE bit. Software
must clear the IBIF bit in the interrupt routine first. The TCF bit will be
cleared by reading from the IIC Bus Data I/O Register (IBDR) in receive
mode or writing to IBDR in transmit mode.
Software may service the IIC I/O in the main program by monitoring the
IBIF bit if the interrupt function is disabled. Note that polling should
monitor the IBIF bit rather than the TCF bit since their operation is
different when arbitration is lost.
Note that when an interrupt occurs at the end of the address cycle the
master will always be in transmit mode, i.e. the address is transmitted. If
master receive mode is required, indicated by R/W bit in IBDR, then the
Tx/Rx bit should be toggled at this stage.
During slave mode address cycles (IAAS=1) the SRW bit in the status
register is read to determine the direction of the subsequent transfer and
the Tx/Rx bit is programmed accordingly. For slave mode data cycles
(IAAS=0) the SRW bit is not valid, the Tx/Rx bit in the control register
should be read to determine the direction of the current transfer.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
291
Freescale Semiconductor, Inc.
Inter-IC Bus
The following is an example of a software response by a ’master
transmitter’ in the interrupt routine (see Figure 15-4).
ISR
TRANSMIT
BCLR
BRCLR
BRCLR
BRSET
MOVB
IBSR,#$02
IBCR,#$20,SLAVE
IBCR,#$10,RECEIVE
IBSR,#$01,END
DATABUF,IBDR
;CLEAR THE IBIF FLAG
;BRANCH IF IN SLAVE MODE
;BRANCH IF IN RECEIVE MODE
;IF NO ACK, END OF TRANSMISSION
;TRANSMIT NEXT BYTE OF DATA
Freescale Semiconductor, Inc...
15.7.4 Generation of STOP
A data transfer ends with a STOP signal generated by the ’master’
device. A master transmitter can simply generate a STOP signal after all
the data has been transmitted. The following is an example showing how
a stop condition is generated by a master transmitter.
MASTX
TST
TXCNT
END
EMASTX
BEQ
BRSET
MOVB
DEC
BRA
BCLR
RTI
END
IBSR,#$01,END
DATABUF,IBDR
TXCNT
EMASTX
IBCR,#$20
;GET VALUE FROM THE
;TRANSMITING COUNTER
;END IF NO MORE DATA
;END IF NO ACK
;TRANSMIT NEXT BYTE OF DATA
;DECREASE THE TXCNT
;EXIT
;GENERATE A STOP CONDITION
;RETURN FROM INTERRUPT
If a master receiver wants to terminate a data transfer, it must inform the
slave transmitter by not acknowledging the last byte of data which can
be done by setting the transmit acknowledge bit (TXAK) before reading
the 2nd last byte of data. Before reading the last byte of data, a STOP
signal must be generated first. The following is an example showing how
a STOP signal is generated by a master receiver.
MASR
LAMAR
DEC
BEQ
MOVB
DEC
BNE
BSET
RXCNT
ENMASR
RXCNT,D1
D1
NXMAR
IBCR,#$08
ENMASR
BRA
BCLR
NXMAR
IBCR,#$20
;DECREASE THE RXCNT
;LAST BYTE TO BE READ
;CHECK SECOND LAST BYTE
;TO BE READ
;NOT LAST OR SECOND LAST
;SECOND LAST, DISABLE ACK
;TRANSMITTING
;LAST ONE, GENERATE ‘STOP’ SIGNAL
Technical Data
292
MC68HC912DG128 — Rev 3.0
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Inter-IC Bus
IIC Programming Examples
MASR
NXMAR
DEC
MOVB
RTI
RXCNT
IBDR,RXBUF
;DECREASE THE RXCNT
;READ DATA AND STORE
15.7.5 Generation of Repeated START
At the end of data transfer, if the master still wants to communicate on
the bus, it can generate another START signal followed by another slave
address without first generating a STOP signal. A program example is
as shown.
RESTART
BSET
MOVB
IBCR,#$04
CALLING,IBDR
ANOTHER START (RESTART)
;TRANSMIT THE CALLING ADDRESS
;D0=R/W
15.7.6 Slave Mode
In the slave interrupt service routine, the module addressed as slave bit
(IAAS) should be tested to check if a calling of its own address has just
been received (see Figure 15-4). If IAAS is set, software should set the
transmit/receive mode select bit (Tx/Rx bit of IBCR) according to the
R/W command bit (SRW). Writing to the IBCR clears the IAAS
automatically. Note that the only time IAAS is read as set is from the
interrupt at the end of the address cycle where an address match
occurred, interrupts resulting from subsequent data transfers will have
IAAS cleared. A data transfer may now be initiated by writing information
to IBDR, for slave transmits, or dummy reading from IBDR, in slave
receive mode. The slave will drive SCL low in-between byte transfers,
SCL is released when the IBDR is accessed in the required mode.
In the slave transmitter routine, the received acknowledge bit (RXAK)
must be tested before transmitting the next byte of data. Setting RXAK
means an ’end of data’ signal from the master receiver, after which it
must be switched from transmitter mode to receiver mode by software.
A dummy read then releases the SCL line so that the master can
generate a STOP signal.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
293
Freescale Semiconductor, Inc.
Inter-IC Bus
15.7.7 Arbitration Lost
Freescale Semiconductor, Inc...
If several masters try to engage the bus simultaneously, only one master
wins and the others lose arbitration. The devices which lost arbitration
are immediately switched to slave receive mode by the hardware. Their
data output to the SDA line is stopped, but SCL is still generated until the
end of the byte during which arbitration was lost. An interrupt occurs at
the falling edge of the ninth clock of this transfer with IBAL=1 and
MS/SL=0. If one master attempts to start transmission while the bus is
being engaged by another master, the hardware will inhibit the
transmission; switch the MS/SL bit from 1 to 0 without generating STOP
condition; generate an interrupt to CPU and set the IBAL to indicate that
the attempt to engage the bus is failed. When considering these cases,
the slave service routine should test the IBAL first and the software
should clear the IBAL bit if it is set.
Technical Data
294
MC68HC912DG128 — Rev 3.0
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Inter-IC Bus
Clear
IBIF
Master
Mode
?
Y
Freescale Semiconductor, Inc...
TX
N
Y
RX
Tx/Rx
?
Arbitration
Lost
?
N
Last Byte
Transmitted
?
Clear IBAL
Y
N
RXAK=0
?
Last
Byte To Be Read
?
N
N
Y
N
Y
Y
IAAS=1
?
IAAS=1
?
Y
N
Data Transfer
Address Transfer
End Of
Addr Cycle
(Master Rx)
?
N
Y
Y
Y
(Read)
2nd Last
Byte To Be Read
?
Set TXAK =1
Generate
Stop Signal
Switch To
Rx Mode
Generate
Stop Signal
Read Data
From IBDR
And Store
ACK From
Receiver
?
N
Read Data
From IBDR
And Store
Tx Next
Byte
Write Data
To IBDR
Dummy Read
From IBDR
TX
Y
Set TX
Mode
RX
TX/RX
?
N (Write)
N
Write Next
Byte To IBDR
SRW=1
?
Set RX
Mode
Switch To
Rx Mode
Dummy Read
From IBDR
Dummy Read
From IBDR
RTI
Figure 15-4. Flow-Chart of Typical IIC Interrupt Routine
Technical Data
295
MC68HC912DG128 — Rev 3.0
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Inter-IC Bus
Technical Data
296
MC68HC912DG128 — Rev 3.0
Inter-IC Bus
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Section 16. Analog-to-Digital Converter
16.1 Contents
16.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 297
16.3
Functional Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 298
16.4
ATD Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 299
16.5
ATD Mode Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 310
16.2 Introduction
The MC68HC912DG128 has two identical ATD modules identified as
ATD0 and ATD1. Except for the VDDA and VSSA Analog supply voltage,
all pins are duplicated and indexed with ‘0’ or ‘1’ in the following
description. An ‘x’ indicates either ‘0’ or ‘1’.
The ATD module is an 8-channel, 10-bit or 8-bit, multiplexed-input
successive-approximation analog-to-digital converter. It does not
require external sample and hold circuits because of the type of charge
redistribution technique used. The ATD converter timing can be
synchronized to the system P clock. The ATD module consists of a 16word (32-byte) memory-mapped control register block used for control,
testing and configuration.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Analog-to-Digital Converter
For More Information On This Product,
Go to: www.freescale.com
297
Analog-to-Digital Converter
VRHx
RC DAC ARRAY
AND COMPARATOR
VRLx
REFERENCE
VDDA
SUPPLY
VSSA
MODE AND TIMING CONTROLS
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
SAR
ATD 0
ANALOG MUX
AND
SAMPLE BUFFER AMP
ATD 1
ATD 2
ATD 3
ATD 4
ANx7/PADx7
ANx6/PADx6
ANx5/PADx5
ANx4/PADx4
ANx3/PADx3
ANx2/PADx2
ANx1/PADx1
ANx0/PADx0
PORT AD
DATA INPUT REGISTER
ATD 5
ATD 6
ATD 7
CLOCK
SELECT/PRESCALE
INTERNAL BUS
Figure 16-1. Analog-to-Digital Converter Block Diagram
16.3 Functional Description
A single conversion sequence consists of four or eight conversions,
depending on the state of the select 8 channel mode (S8CM) bit when
ATDxCTL5 is written. There are eight basic conversion modes. In the
non-scan modes, the SCF bit is set after the sequence of four or eight
conversions has been performed and the ATD module halts. In the scan
modes, the SCF bit is set after the first sequence of four or eight
conversions has been performed, and the ATD module continues to
restart the sequence. In both modes, the CCF bit associated with each
register is set when that register is loaded with the appropriate
conversion result. That flag is cleared automatically when that result
register is read. The conversions are started by writing to the control
registers.
Technical Data
298
MC68HC912DG128 — Rev 3.0
Analog-to-Digital Converter
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Analog-to-Digital Converter
ATD Registers
16.4 ATD Registers
Control and data registers for the ATD modules are described below.
Both ATDs have identical control registers mapped in two blocks of 16
bytes.
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
ATD0CTL0/ATD1CTL0 — Reserved
$0060/$01E0
Writes to this register will abort current conversion sequence.
READ: any time WRITE: any time.
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
ATD0CTL1/ATD1CTL1 — Reserved
$0061/$01E1
WRITE: Write to this register has no meaning.
READ: Special Mode only.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Analog-to-Digital Converter
For More Information On This Product,
Go to: www.freescale.com
299
Freescale Semiconductor, Inc.
Analog-to-Digital Converter
Bit 7
6
5
4
3
2
1
Bit 0
ADPU
AFFC
AWAI
0
0
0
ASCIE
ASCIF
0
0
0
0
0
0
0
0
RESET:
ATD0CTL2/ATD1CTL2 — ATD Control Register 2
$0062/$01E2
Freescale Semiconductor, Inc...
The ATD control register 2 and 3 are used to select the power up mode,
interrupt control, and freeze control. Writes to these registers abort any
current conversion sequence.
Read or write anytime except ASCIF bit, which cannot be written.
Bit positions ATDCTL2[4:2] and ATDCTL3[7:2] are unused and always
read as zeros.
ADPU — ATD Disable
0 = Disables the ATD, including the analog section for reduction in
power consumption.
1 = Allows the ATD to function normally.
Software can disable the clock signal to the A/D converter and power
down the analog circuits to reduce power consumption. When reset
to zero, the ADPU bit aborts any conversion sequence in progress.
Because the bias currents to the analog circuits are turned off, the
ATD requires a period of recovery time to stabilize the analog circuits
after setting the ADPU bit.
AFFC — ATD Fast Flag Clear All
0 = ATD flag clearing operates normally (read the status register
before reading the result register to clear the associated CCF
bit).
1 = Changes all ATD conversion complete flags to a fast clear
sequence. Any access to a result register (ATD0–7) will cause
the associated CCF flag to clear automatically if it was set at
the time.
AWAI — ATD Wait Mode
0 = ATD continues to run when the MCU is in wait mode
1 = ATD stops to save power when the MCU is in wait mode
Technical Data
300
MC68HC912DG128 — Rev 3.0
Analog-to-Digital Converter
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Analog-to-Digital Converter
ATD Registers
When the AWAI bit is set and the module enters wait mode, most of
the clocks stop and the analog portion powers down. When the
module comes out of wait, it is recommended that a stabilisation delay
(stop and ATD power up recovery time, tSR) is allowed before new
conversions are started. Additionally, the ATD does not re-initialise
automatically on leaving wait mode.
ASCIE — ATD Sequence Complete Interrupt Enable
0 = Disables ATD interrupt
1 = Enables ATD interrupt on sequence complete
ASCIF — ATD Sequence Complete Interrupt Flag
Cannot be written in any mode.
0 = No ATD interrupt occurred
1 = ATD sequence complete
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
FRZ1
FRZ0
0
0
0
0
0
0
0
0
ATD0CTL3/ATD1CTL3 — ATD Control Register 3
$0063/$01E3
FRZ1, FRZ0 — Background Debug (Freeze) Enable (suspend module
operation at breakpoint)
When debugging an application, it is useful in many cases to have the
ATD pause when a breakpoint is encountered. These two bits
determine how the ATD will respond when background debug mode
becomes active.
Table 16-1. ATD Response to Background Debug Enable
FRZ1
0
0
1
1
FRZ0
0
1
0
1
ATD Response
Continue conversions in active background mode
Reserved
Finish current conversion, then freeze
Freeze when BDM is active
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Analog-to-Digital Converter
For More Information On This Product,
Go to: www.freescale.com
301
Freescale Semiconductor, Inc.
Analog-to-Digital Converter
Bit 7
6
5
4
3
2
1
Bit 0
RES10
SMP1
SMP0
PRS4
PRS3
PRS2
PRS1
PRS0
0
0
0
0
0
0
0
1
RESET:
ATD0CTL4/ATD1CTL4 — ATD Control Register 4
$0064/$01E4
Freescale Semiconductor, Inc...
The ATD control register 4 is used to select the clock source and set up
the prescaler. Writes to the ATD control registers initiate a new
conversion sequence. If a write occurs while a conversion is in progress,
the conversion is aborted and ATD activity halts until a write to
ATDxCTL5 occurs.
RES10 — 10 bit Mode
0 = 8 bit operation
1 = 10 bit operation
SMP1, SMP0 — Select Sample Time
Used to select one of four sample times after the buffered sample and
transfer has occurred.
Table 16-2. Final Sample Time Selection
SMP1
0
0
1
1
SMP0
0
1
0
1
Final Sample Time
2 A/D clock periods
4 A/D clock periods
8 A/D clock periods
16 A/D clock periods
Technical Data
302
MC68HC912DG128 — Rev 3.0
Analog-to-Digital Converter
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Analog-to-Digital Converter
ATD Registers
PRS4, PRS3, PRS2, PRS1, PRS0 — Select Divide-By Factor for ATD
P-Clock Prescaler.
Freescale Semiconductor, Inc...
The binary value written to these bits (1 to 31) selects the divide-by
factor for the modulo counter-based prescaler. The P clock is divided
by this value plus one and then fed into a ÷2 circuit to generate the
ATD module clock. The divide-by-two circuit insures symmetry of the
output clock signal. Clearing these bits causes the prescale value
default to one which results in a ÷2 prescale factor. This signal is then
fed into the ÷2 logic. The reset state divides the P clock by a total of
four and is appropriate for nominal operation at 2 MHz. Table 16-3
shows the divide-by operation and the appropriate range of system
clock frequencies.
Table 16-3. Clock Prescaler Values
Prescale
Value
00000
00001
00010
00011
00100
00101
00110
00111
01xxx
1xxxx
Total Divisor
Max P Clock(1)
Min P Clock(2)
÷2
÷4
÷6
÷8
÷10
÷12
÷14
÷16
4 MHz
8 MHz
8 MHz
8 MHz
8 MHz
8 MHz
8 MHz
8 MHz
1 MHz
2 MHz
3 MHz
4 MHz
5 MHz
6 MHz
7 MHz
8 MHz
Do Not Use
1. Maximum conversion frequency is 2 MHz. Maximum P clock divisor value will become
maximum conversion rate that can be used on this ATD module.
2. Minimum conversion frequency is 500 kHz. Minimum P clock divisor value will become
minimum conversion rate that this ATD can perform.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Analog-to-Digital Converter
For More Information On This Product,
Go to: www.freescale.com
303
Freescale Semiconductor, Inc.
Analog-to-Digital Converter
Bit 7
6
5
4
3
2
1
Bit 0
0
S8CM
SCAN
MULT
CD
CC
CB
CA
0
0
0
0
0
0
0
0
RESET:
ATD0CTL5/ATD1CTL5 — ATD Control Register 5
$0065/$01E5
Freescale Semiconductor, Inc...
The ATD control register 5 is used to select the conversion modes, the
conversion channel(s), and initiate conversions.
Read or write any time. Writes to the ATD control registers initiate a new
conversion sequence. If a conversion sequence is in progress when a
write occurs, that sequence is aborted and the SCF and CCF bits are
reset.
S8CM — Select 8 Channel Mode
0 = Conversion sequence consists of four conversions
1 = Conversion sequence consists of eight conversions
SCAN — Enable Continuous Channel Scan
0 = Single conversion sequence
1 = Continuous conversion sequences (scan mode)
When a conversion sequence is initiated by a write to the ATDxCTL
register, the user has a choice of performing a sequence of four (or
eight, depending on the S8CM bit) conversions or continuously
performing four (or eight) conversion sequences.
MULT — Enable Multichannel Conversion
0 = ATD sequencer runs all four or eight conversions on a single
input channel selected via the CD, CC, CB, and CA bits.
1 = ATD sequencer runs each of the four or eight conversions on
sequential channels in a specific group. Refer to Table 16-4.
Technical Data
304
MC68HC912DG128 — Rev 3.0
Analog-to-Digital Converter
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Analog-to-Digital Converter
ATD Registers
CD, CC, CB, and CA — Channel Select for Conversion
Table 16-4. Multichannel Mode Result Register Assignment
Freescale Semiconductor, Inc...
S8CM
CD
CB
CA
Channel Signal
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
1
0
1
0
AN0
AN1
AN2
AN3
AN4
AN5
AN6
AN7
Reserved
Reserved
Reserved
Reserved
VRH
Result in ADRxx
if MULT = 1
ADRx0
ADRx1
ADRx2
ADRx3
ADRx0
ADRx1
ADRx2
ADRx3
ADRx0
ADRx1
ADRx2
ADRx3
ADRx0
0
1
VRL
ADRx1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
(VRH + VRL)/2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
1
0
0
TEST/Reserved
AN0
AN1
AN2
AN3
AN4
AN5
AN6
AN7
Reserved
Reserved
Reserved
Reserved
VRH
ADRx2
ADRx3
ADRx0
ADRx1
ADRx2
ADRx3
ADRx4
ADRx5
ADRx6
ADRx7
ADRx0
ADRx1
ADRx2
ADRx3
ADRx5
ADRx6
CC
0
0
0
0
0
1
0
1
0
0
1
1
1
0
1
1
1
0
1
VRL
1
1
0
(VRH + VRL)/2
ADRx4
1
1
1
TEST/Reserved
ADRx7
Shaded bits are “don’t care” if MULT = 1 and the entire block of four or eight
channels make up a conversion sequence. When MULT = 0, all four bits (CD,
CC, CB, and CA) must be specified and a conversion sequence consists of
four or eight consecutive conversions of the single specified channel.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Analog-to-Digital Converter
For More Information On This Product,
Go to: www.freescale.com
305
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Analog-to-Digital Converter
NOTE:
Conversion of (VRH-VRL)/2 returns $7F, $80 or $81 in 8-bit mode.
Bit 7
6
5
4
3
2
1
Bit 0
SCF
0
0
0
0
CC2
CC1
CC0
0
0
0
0
0
0
0
0
RESET:
ATD0STAT0/ATD1STAT0 — ATD Status Register
$0066/$01E6
ATD0STAT1/ATD1STAT1 — ATD Status Register
$0067/$01E7
RESET:
Bit 7
CCF7
0
6
CCF6
0
5
CCF5
0
4
CCF4
0
3
CCF3
0
2
CCF2
0
1
CCF1
0
Bit 0
CCF0
0
The ATD status registers contain the flags indicating the completion of
ATD conversions.
Normally, it is read-only. In special mode, the SCF bit and the CCF bits
may also be written.
SCF — Sequence Complete Flag
This bit is set at the end of the conversion sequence when in the
single conversion sequence mode (SCAN = 0 in ATDxCTL5) and is
set at the end of the first conversion sequence when in the continuous
conversion mode (SCAN = 1 in ATDxCTL5). When AFFC = 0, SCF is
cleared when a write is performed to ATDxCTL5 to initiate a new
conversion sequence. When AFFC = 1, SCF is cleared after the first
result register is read.
CC[2:0] — Conversion Counter for Current Sequence of Four or Eight
Conversions
This 3-bit value reflects the contents of the conversion counter pointer
in a four or eight count sequence. This value also reflects which result
register will be written next, indicating which channel is currently being
converted.
CCF[7:0] — Conversion Complete Flags
Technical Data
306
MC68HC912DG128 — Rev 3.0
Analog-to-Digital Converter
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Analog-to-Digital Converter
ATD Registers
Each of these bits are associated with an individual ATD result
register. For each register, this bit is set at the end of conversion for
the associated ATD channel and remains set until that ATD result
register is read. It is cleared at that time if AFFC bit is set, regardless
of whether a status register read has been performed (i.e., a status
register read is not a pre-qualifier for the clearing mechanism when
AFFC = 1). Otherwise the status register must be read to clear the
flag.
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
SAR9
SAR8
SAR7
SAR6
SAR5
SAR4
SAR3
SAR2
0
0
0
0
0
0
0
0
ATD0TESTH/ATD1TESTH — ATD Test Register
RESET:
$0068/$01E8
Bit 7
6
5
4
3
2
1
Bit 0
SAR1
SAR0
RST
TSTOUT
TST3
TST2
TST1
TST0
0
0
0
0
0
0
0
0
ATD0TESTL/ATD1TESTL — ATD Test Register
$0069/$01E9
The test registers control various special modes which are used
during manufacturing. The test register can be read or written only in
the special modes. In the normal modes, reads of the test register
return zero and writes have no effect.
SAR[9:0] — SAR Data
Reads of this byte return the current value in the SAR. Writes to this
byte change the SAR to the value written. Bits SAR[9:0] reflect the ten
SAR bits used during the resolution process for a 10-bit result.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Analog-to-Digital Converter
For More Information On This Product,
Go to: www.freescale.com
307
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Analog-to-Digital Converter
RST — Module Reset Bit
When set, this bit causes all registers and activity in the module to
assume the same state as out of power-on reset (except for ADPU bit
in ATDCTL2, which remains set, allowing the ATD module to remain
enabled).
TSTOUT — Multiplex Output of TST[3:0] (Factory Use)
TST[3:0] — Test Bits 3 to 0 (Reserved)
Selects one of 16 reserved factory testing modes
Bit 7
6
5
4
3
2
1
Bit 0
PADx7
PADx6
PADx5
PADx4
PADx3
PADx2
PADx1
PADx0
-
-
-
-
-
-
-
-
RESET:
PORTAD0/PORTAD1 — Port AD Data Input Register
$006F/$01EF
PADx[7:0] — Port AD Data Input Bits
After reset these bits reflect the state of the input pins.
May be used for general-purpose digital input. When the software
reads PORTADx, it obtains the digital levels that appear on the
corresponding port AD pins. Pins with signals not meeting VIL or VIH
specifications will have an indeterminate value. Writes to this register
have no meaning at any time.
Technical Data
308
MC68HC912DG128 — Rev 3.0
Analog-to-Digital Converter
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Analog-to-Digital Converter
ATD Registers
8-bit mode
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
10-bit mode
Bit 9
Bit 8
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
RESET:
u
u
u
u
u
u
u
u
ADRx0H — A/D Conversion Result Register High 0
ADRx1H — A/D Conversion Result Register High 1
ADRx2H — A/D Conversion Result Register High 2
ADRx3H — A/D Conversion Result Register High 3
ADRx4H — A/D Conversion Result Register High 4
ADRx5H — A/D Conversion Result Register High 5
ADRx6H — A/D Conversion Result Register High 6
ADRx7H — A/D Conversion Result Register High 7
$0070/$01F0
$0072/$01F2
$0074/$01F4
$0076/$01F6
$0078/$01F8
$007A/$01FA
$007C/$01FC
$007E/$01FE
ADRxxH[7:0] — ATD Conversion result (high)
The reset condition for these registers is undefined.
In 8-bit mode, these registers contain the left-justified, unsigned result
from the 8-bit ATD conversion.
In 10-bit mode these registers contain the high order bits of the
conversion result.
8-bit mode
—
—
—
—
—
—
—
—
10-bit mode
Bit 1
Bit 0
—
—
—
—
—
—
RESET:
u
u
u
u
u
u
u
u
ADRx0L — A/D Conversion Result Register Low 0
ADRx1L — A/D Conversion Result Register Low 1
ADRx2L — A/D Conversion Result Register Low 2
ADRx3L — A/D Conversion Result Register Low 3
ADRx4L — A/D Conversion Result Register Low 4
ADRx5L — A/D Conversion Result Register Low 5
ADRx6L — A/D Conversion Result Register Low 6
ADRx7L — A/D Conversion Result Register Low 7
$0071/$01F1
$0073/$01F3
$0075/$01F5
$0077/$01F7
$0079/$01F9
$007B/$01FB
$007D/$01FD
$007F/$01FF
ADRxxL[7:0] — ATD Conversion result (low)
The reset condition for these registers is undefined.
In 8-bit mode, these registers bits are reserved.
In 10-bit mode these registers contain the remaining two low order
bits of the conversion result in bits 6 and 7.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Analog-to-Digital Converter
For More Information On This Product,
Go to: www.freescale.com
309
Freescale Semiconductor, Inc.
Analog-to-Digital Converter
The channel from which this result was obtained is dependent on the
conversion mode selected. The registers are always read-only in normal
mode.
16.5 ATD Mode Operation
Freescale Semiconductor, Inc...
STOP — causes all clocks to halt (if the S bit in the CCR is zero). The
system is placed in a minimum-power standby mode. This aborts any
conversion sequence in progress.
WAIT — ATD conversion continues unless AWAI bit in ATDxCTL2
register is set.
BDM — Debug options available as set in register ATDxCTL3.
USER — ATD continues running unless ADPU is cleared.
ADPU — ATD operations are stopped if ADPU = 0, but registers are
accessible.
Technical Data
310
MC68HC912DG128 — Rev 3.0
Analog-to-Digital Converter
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Section 17. MSCAN Controller
17.1 Contents
17.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 311
17.3
External Pins. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 312
17.4
Message Storage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 313
17.5
Identifier Acceptance Filter . . . . . . . . . . . . . . . . . . . . . . . . . . . 318
17.6
Interrupts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 322
17.7
Protocol Violation Protection. . . . . . . . . . . . . . . . . . . . . . . . . . 324
17.8
Low Power Modes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .325
17.9
Timer Link . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
17.10 Clock System . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 329
17.11 Memory Map. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 332
17.12 Programmer’s Model of Message Storage . . . . . . . . . . . . . . .332
17.13 Programmer’s Model of Control Registers . . . . . . . . . . . . . . . 338
17.2 Introduction
The MC68HC912DG128 has two identical msCAN12 modules,
identified as CAN0 and CAN1. The information to follow describes one
msCAN unless specifically noted and register locations specifically
relate to CAN0. CAN1 registers are located 512 bytes from CAN0.
The msCAN12 is the specific implementation of the Motorola scalable
CAN (msCAN) concept targeted for the Motorola M68HC12
microcontroller family.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
311
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
The module is a communication controller implementing the CAN 2.0
A/B protocol as defined in the BOSCH specification dated September
1991.
The CAN protocol was primarily, but not only, designed to be used as a
vehicle serial data bus, meeting the specific requirements of this field:
real-time processing, reliable operation in the EMI environment of a
vehicle, cost-effectiveness and required bandwidth.
msCAN12 utilizes an advanced buffer arrangement resulting in a
predictable real-time behavior and simplifies the application software.
17.3 External Pins
The msCAN12 uses 2 external pins, 1 input (RxCAN) and 1 output
(TxCAN). The TxCAN output pin represents the logic level on the CAN:
0 is for a dominant state, and 1 is for a recessive state.
RxCAN is on bit 0 of Port CAN, TxCAN is on bit 1. The remaining six pins
of Port CAN are controlled by registers in the msCAN12 address space
(see msCAN12 Port CAN Control Register (PCTLCAN) and msCAN12
Port CAN Data Direction Register (DDRCAN)).
A typical CAN system with msCAN12 is shown in Figure 17-1.
Each CAN station is connected physically to the CAN bus lines through
a transceiver chip. The transceiver is capable of driving the large current
needed for the CAN and has current protection, against defective CAN
or defective stations.
Technical Data
312
MC68HC912DG128 — Rev 3.0
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
Message Storage
CAN station 1
CAN station 2
.....
CAN station n
CAN system
msCAN12
Controller
TxCAN
RxCAN
Transceiver
CAN
Figure 17-1. The CAN System
17.4 Message Storage
msCAN12 facilitates a sophisticated message storage system which
addresses the requirements of a broad range of network applications.
17.4.1 Background
Modern application layer software is built upon two fundamental
assumptions:
1. Any CAN node is able to send out a stream of scheduled
messages without releasing the bus between two messages.
Such nodes will arbitrate for the bus right after sending the
previous message and will only release the bus arbitration is lost.
2. The internal message queue within any CAN node is organized
such that if more than one message is ready to be sent, the
highest priority message will be sent out first.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
313
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
The bove behavior cannot be achieved with a single transmit buffer. That
buffer must be reloaded right after the previous message has been sent.
This loading process lasts a definite amount of time and has to be
completed within the inter-frame sequence (IFS) in order to be able to
send an uninterrupted stream of messages. Even if this is feasible for
limited CAN bus speeds it requires that the CPU reacts with short
latencies to the transmit interrupt.
A double buffer scheme would de-couple the re-loading of the transmit
buffers from the actual message sending and as such reduces the
reactiveness requirements on the CPU. Problems may arise if the
sending of a message would be finished just while the CPU re-loads the
second buffer, no buffer would then be ready for transmission and the
bus would be released.
At least three transmit buffers are required to meet the first of above
requirements under all circumstances. The msCAN12 has three transmit
buffers.
The second requirement calls for some sort of internal prioritization
which the msCAN12 implements with the local priority concept
described below.
17.4.2 Receive Structures
The received messages are stored in a two stage input FIFO. The two
message buffers are alternately mapped into a single memory area (see
Figure 17-2). While the background receive buffer (RxBG) is exclusively
associated to the msCAN12, the foreground receive buffer (RxFG) is
addressable by the CPU12. This scheme simplifies the handler software
as only one address area is applicable for the receive process.
Both buffers have a size of 13 bytes to store the CAN control bits, the
identifier (standard or extended) and the data contents (for details see
Programmer’s Model of Message Storage).
The receiver full flag (RXF) in the msCAN12 receiver flag register
(CRFLG) (see msCAN12 Receiver Flag Register (CRFLG)) signals the
status of the foreground receive buffer. When the buffer contains a
correctly received message with matching identifier this flag is set.
Technical Data
314
MC68HC912DG128 — Rev 3.0
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN Controller
Message Storage
On reception, each message is checked to see if it passes the filter (for
details see Identifier Acceptance Filter) and in parallel is written into
RxBG. The msCAN12 copies the content of RxBG into RxFG(1), sets the
RXF flag, and generates a receive interrupt to the CPU(2). The user’s
receive handler has to read the received message from RxFG and then
reset the RXF flag in order to acknowledge the interrupt and to release
the foreground buffer. A new message, which can follow immediately
after the IFS field of the CAN frame, is received into RxBG.
Freescale Semiconductor, Inc...
The over-writing of the background buffer is independent of the identifier
filter function.
1. Only if the RXF flag is not set.
2. The receive interrupt is generated only if not masked. A polling scheme can be applied on RXF
also.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
315
Freescale Semiconductor, Inc.
MSCAN Controller
msCAN12
CPU bus
Freescale Semiconductor, Inc...
RxBG
RxFG
RXF
Tx0
TXE
PRIO
Tx1
TXE
PRIO
Tx2
TXE
PRIO
Figure 17-2. User Model for Message Buffer Organization
When the msCAN12 module is transmitting, the msCAN12 receives its
own messages into the background receive buffer, RxBG, but does NOT
overwrite RxFG, generate a receive interrupt or acknowledge its own
messages on the CAN bus. The exception to this rule is in loop-back
mode (see msCAN12 Module Control Register 0 (CMCR0)) where the
msCAN12 treats its own messages exactly like all other incoming
messages. The msCAN12 receives its own transmitted messages in the
event that it loses arbitration. If arbitration is lost, the msCAN12 must be
prepared to become receiver.
Technical Data
316
MC68HC912DG128 — Rev 3.0
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
Message Storage
An overrun condition occurs when both the foreground and the
background receive message buffers are filled with correctly received
messages with accepted identifiers and another message is correctly
received from the bus with an accepted identifier. The latter message is
discarded and an error interrupt with overrun indication is generated if
enabled. The msCAN12 is still able to transmit messages with both
receive message buffers filled, but all incoming messages are
discarded.
NOTE:
The msCAN12 will receive its own messages into the background
receive buffer RxBG but will not overwrite RxFG and will not emit a
receive interrupt nor will it acknowledge (ACK) its own messages on the
CAN bus. The exception to this rule is that when in loop-back mode
msCAN12 will treat its own messages exactly like all other incoming
messages.
17.4.3 Transmit Structures
The msCAN12 has a triple transmit buffer scheme in order to allow
multiple messages to be set up in advance and to achieve an optimized
real-time performance. The three buffers are arranged as shown in
Figure 17-2.
All three buffers have a 13 byte data structure similar to the outline of the
receive buffers (see Programmer’s Model of Message Storage). An
additional transmit buffer priority register (TBPR) contains an 8-bit so
called local priority field (PRIO) (see Transmit Buffer Priority Registers
(TBPR)).
In order to transmit a message, the CPU12 has to identify an available
transmit buffer which is indicated by a set transmit buffer empty (TXE)
flag in the msCAN12 transmitter flag register (CTFLG) (see msCAN12
Transmitter Flag Register (CTFLG)).
The CPU12 then stores the identifier, the control bits and the data
content into one of the transmit buffers. Finally, the buffer has to be
flagged as being ready for transmission by clearing the TXE flag.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
317
Freescale Semiconductor, Inc.
MSCAN Controller
The msCAN12 will then schedule the message for transmission and will
signal the successful transmission of the buffer by setting the TXE flag.
A transmit interrupt will be emitted(1) when TXE is set and this can be
used to drive the application software to re-load the buffer.
Freescale Semiconductor, Inc...
If more than one buffer is scheduled for transmission when the CAN bus
becomes available for arbitration, the msCAN12 uses the local priority
setting of the three buffers for prioritisation. For this purpose every
transmit buffer has an 8-bit local priority field (PRIO). The application
software sets this field when the message is set up. The local priority
reflects the priority of this particular message relative to the set of
messages being emitted from this node. The lowest binary value of the
PRIO field is defined to be the highest priority.
The internal scheduling process takes places whenever the msCAN12
arbitrates for the bus. This is also the case after the occurrence of a
transmission error.
When a high priority message is scheduled by the application software
it may become necessary to abort a lower priority message being set up
in one of the three transmit buffers. As messages that are already under
transmission cannot be aborted, the user has to request the abort by
setting the corresponding abort request flag (ABTRQ) in the
transmission control register (CTCR). The msCAN12 grants the request,
if possible, by setting the corresponding abort request acknowledge
(ABTAK) and the TXE flag in order to release the buffer and by
generating a transmit interrupt. The transmit interrupt handler software
can tell from the setting of the ABTAK flag whether the message was
aborted (ABTAK=1) or sent in the meantime (ABTAK=0).
17.5 Identifier Acceptance Filter
The identifier acceptance registers (CIDAR0–7) define the acceptable
patterns of the standard or extended identifier (ID10–ID0 or ID28–ID0).
Any of these bits can be marked don’t care in the identifier mask
registers (CIDMR0–7).
1. The transmit interrupt will occur only if not masked. A polling scheme can be applied on TXE
also.
Technical Data
318
MC68HC912DG128 — Rev 3.0
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN Controller
Identifier Acceptance Filter
A filter hit is indicated to the application software by a set RXF (receive
buffer full flag, see msCAN12 Receiver Flag Register (CRFLG)) and
three bits in the identifier acceptance control register (see msCAN12
Identifier Acceptance Control Register (CIDAC)). These identifier hit
flags (IDHIT2–0) clearly identify the filter section that caused the
acceptance. They simplify the application software’s task to identify the
cause of the receiver interrupt. When more than one hit occurs (two or
more filters match) the lower hit has priority.
Freescale Semiconductor, Inc...
A very flexible programmable generic identifier acceptance filter has
been introduced in order to reduce the CPU interrupt loading. The filter
is programmable to operate in four different modes:
•
Two identifier acceptance filters, each to be applied to:
a) the full 29 bits of the extended identifier and to the following bits
of the CAN frame: RTR, IDE, SRR or
b) the 11 bits of the standard identifier, the RTR and IDE bits of
CAN 2.0A/B messages.
This mode implements two filters for a full length CAN 2.0B
compliant extended identifier. Figure 17-3 shows how the first 32bit filter bank (CIDAR0–3, CIDMR0–3) produces a filter 0 hit.
Similarly, the second filter bank (CIDAR4–7, CIDMR4–7)
produces a filter 1 hit.
•
Four identifier acceptance filters, each to be applied to:
a) the 14 most significant bits of the extended identifier plus the
SRR and IDE bits of CAN 2.0B messages or
b) the 11 bits of the standard identifier, the RTR and IDE bits of
CAN 2.0A/B messages.
Figure 17-4 shows how the first 32-bit filter bank (CIDAR0–3,
CIDMR0–3) produces filter 0 and 1 hits. Similarly, the second filter
bank (CIDAR4–7, CIDMR4–7) produces filter 2 and 3 hits.
•
Eight identifier acceptance filters, each to be applied to the first 8
bits of the identifier. This mode implements eight independent
filters for the first 8 bits of a CAN 2.0A/B compliant standard
identifier or of a CAN 2.0B compliant extended identifier. Figure
17-5 shows how the first 32-bit filter bank (CIDAR0–3, CIDMR0–3)
produces filter 0 to 3 hits. Similarly, the second filter bank
(CIDAR4–7, CIDMR4–7) produces filter 4 to 7 hits.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
319
Freescale Semiconductor, Inc.
MSCAN Controller
•
Closed filter. No CAN message will be copied into the foreground
buffer RxFG, and the RXF flag will never be set.
ID28 IDR0
Freescale Semiconductor, Inc...
ID10 IDR0
ID21 ID20 IDR1
ID3 ID2
ID15
ID14 IDR2
ID7
ID6
IDR3 RTR
IDR1 IDE
AM7 CIDMRO AM0 AM7 CIDMR1 AM0
AM7 CIDMR2 AM0
AM7CIDMR3 AM0
AC7 CIDARO AC0 AC7 CIDAR1 AC0
AC7 CIDAR2 AC0
AC7 CIDAR3 AC0
ID accepted (Filter 0 hit)
Figure 17-3. 32-bit Maskable Identifier Acceptance Filters
ID28 IDR0
ID10 IDR0
ID21 ID20 IDR1
ID3 ID2
ID15
ID14 IDR2
ID7
ID6
IDR3 RTR
IDR1 IDE
AM7 CIDMRO AM0 AM7 CIDMR1 AM0
AC7 CIDARO AC0 AC7 CIDAR1 AC0
ID accepted (Filter 0 hit)
AM7 CIDMR2 AM0 AM7 CIDMR3 AM0
AC7 CIDAR2 AC0 AC7 CIDAR3 AC0
ID accepted (Filter 1 hit)
Figure 17-4. 16-bit Maskable Acceptance Filters
Technical Data
320
MC68HC912DG128 — Rev 3.0
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN Controller
Identifier Acceptance Filter
ID28
IDR0
ID21 ID20
ID10
IDR0
ID3 ID2
IDR1
ID15
ID14 IDR2
ID7
ID6
IDR3
RTR
IDR1 IDE
AM7 CIDMRO AM0
AC7 CIDARO AC0
Freescale Semiconductor, Inc...
ID accepted (Filter 0 hit)
AM7 CIDMR1 AM0
AC7 CIDAR1 AC0
ID accepted (Filter 1 hit)
AM7 CIDMR2 AM0
AC7 CIDAR2 AC0
ID accepted (Filter 2 hit)
AM7 CIDMR3 AM0
AC7 CIDAR3 AC0
Figure 17-5. 8-bit Maskable Acceptance Filters
The identifier acceptance registers (CIDAR0–7) define the acceptable
patterns of the standard or extended identifier (ID10–ID0 or ID28–ID0).
Any of these bits can be marked don’t care in the identifier mask
registers (CIDMR0–7).
A filter hit is indicated to the application software by a set RXF (receive
buffer full flag, see msCAN12 Receiver Flag Register (CRFLG)) and
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
321
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
three bits in the identifier acceptance control register (see msCAN12
Identifier Acceptance Control Register (CIDAC)). These identifier hit
flags (IDHIT2–0) clearly identify the filter section that caused the
acceptance. They simplify the application software’s task to identify the
cause of the receiver interrupt. In case that more than one hit occurs (two
or more filters match) the lower hit has priority.
A hit will also cause a receiver interrupt if enabled.
17.6 Interrupts
The msCAN12 supports four interrupt vectors mapped onto eleven
different interrupt sources, any of which can be individually masked (for
details see msCAN12 Receiver Flag Register (CRFLG) to msCAN12
Transmitter Control Register (CTCR)):
•
Transmit interrupt: At least one of the three transmit buffers is
empty (not scheduled) and can be loaded to schedule a message
for transmission. The TXE flags of the empty message buffers are
set.
•
Receive interrupt: A message has been successfully received and
loaded into the foreground receive buffer. This interrupt is
generated immediately after receiving the EOF symbol. The RXF
flag is set.
•
Wake-up interrupt: An activity on the CAN bus occurred during
msCAN12 internal SLEEP mode.
•
Error interrupt: An overrun, error or warning condition occurred.
The receiver flag register (CRFLG) indicates one of the following
conditions:
– Overrun: an overrun condition as described in Receive
Structures has occurred.
– Receiver warning: the receive error counter has reached the
CPU warning limit of 96.
– Transmitter warning: the transmit error counter has reached
the CPU warning limit of 96.
Technical Data
322
MC68HC912DG128 — Rev 3.0
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
Interrupts
– Receiver error passive: the receive error counter has
exceeded the error passive limit of 127 and msCAN12 has
gone to error passive state.
– Transmitter error passive: the transmit error counter has
exceeded the error passive limit of 127 and msCAN12 has
gone to error passive state.
– Bus off: the transmit error counter has exceeded 255 and
msCAN12 has gone to BUSOFF state.
17.6.1 Interrupt Acknowledge
Interrupts are directly associated with one or more status flags in either
the msCAN12 receiver flag register (CRFLG) or the msCAN12
transmitter flag register (CTFLG). Interrupts are pending as long as one
of the corresponding flags is set. The flags in above registers must be
reset within the interrupt handler in order to handshake the interrupt. The
flags are reset through writing a 1 to the corresponding bit position. A flag
cannot be cleared if the respective condition still prevails.
NOTE:
Bit manipulation instructions (BSET) shall not be used to clear interrupt
flags.
17.6.2 Interrupt Vectors
The msCAN12 supports four interrupt vectors as shown in Table 17-1.
The vector addresses and the relative interrupt priority are dependent on
the chip integration and to be defined.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
323
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
Table 17-1. msCAN12 Interrupt Vectors
Function
Wake-Up
Error
Interrupts
Receive
Transmit
Source
WUPIF
RWRNIF
TWRNIF
RERRIF
TERRIF
BOFFIF
OVRIF
RXF
TXE0
TXE1
TXE2
Local Mask
WUPIE
RWRNIE
TWRNIE
RERRIE
TERRIE
BOFFIE
OVRIE
RXFIE
TXEIE0
TXEIE1
TXEIE2
Global Mask
I Bit
17.7 Protocol Violation Protection
The msCAN12 will protect the user from accidentally violating the CAN
protocol through programming errors. The protection logic implements
the following features:
•
The receive and transmit error counters cannot be written or
otherwise manipulated.
•
All registers which control the configuration of the msCAN12
cannot be modified while the msCAN12 is on-line. The SFTRES
bit in CMCR0 (see msCAN12 Module Control Register 0
(CMCR0)) serves as a lock to protect the following registers:
– msCAN12 module control register 1 (CMCR1)
– msCAN12 bus timing register 0 and 1 (CBTR0, CBTR1)
– msCAN12 identifier acceptance control register (CIDAC)
– msCAN12 identifier acceptance registers (CIDAR0–7)
– msCAN12 identifier mask registers (CIDMR0–7)
•
The TxCAN pin is forced to recessive when the msCAN12 is in any
of the low power modes.
Technical Data
324
MC68HC912DG128 — Rev 3.0
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN Controller
Low Power Modes
17.8 Low Power Modes
In addition to normal mode, the msCAN12 has three modes with
reduced power consumption: SLEEP, SOFT_RESET and
POWER_DOWN. In SLEEP and SOFT_RESET modes, power
consumption is reduced by stopping all clocks except those to access
the registers. In POWER_DOWN mode, all clocks are stopped and no
power is consumed.
Freescale Semiconductor, Inc...
The WAI and STOP instructions put the MCU in low power consumption
stand-by modes. Table 17-2 summarizes the combinations of msCAN12
and CPU modes. A particular combination of modes is entered for the
given settings of the bits CSWAI, SLPAK, and SFTRES. For all modes,
an msCAN wake-up interrupt can occur only if SLPAK=WUPIE=1. While
the CPU is in Wait Mode, the msCAN12 can be operated in Normal
Mode and generate interrupts (registers can be accessed via
background debug mode).
Table 17-2. msCAN12 vs. CPU operating modes
STOP
CPU Mode
WAIT
CSWAI = X(1)
SLPAK = X
SFTRES = X
CSWAI = 1
SLPAK = X
SFTRES = X
msCAN Mode
POWER_DOWN
SLEEP
SOFT_RESET
Normal
CSWAI = 0
SLPAK = 1
SFTRES = 0
CSWAI = 0
SLPAK = 0
SFTRES = 1
CSWAI = 0
SLPAK = 0
SFTRES = 0
RUN
CSWAI = X
SLPAK = 1
SFTRES = 0
CSWAI = X
SLPAK = 0
SFTRES = 1
CSWAI = X
SLPAK = 0
SFTRES = 0
1. X means don’t care.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
325
Freescale Semiconductor, Inc.
MSCAN Controller
17.8.1 msCAN12 SLEEP Mode
Freescale Semiconductor, Inc...
The CPU can request the msCAN12 to enter this low-power mode by
asserting the SLPRQ bit in the Module Configuration Register (see
Figure 17-6). The time when the msCAN12 enters Sleep Mode depends
on its activity:
NOTE:
•
If one or more message buffers are scheduled for transmission
(TXEx = 0), the msCAN will continue to transmit until all transmit
message buffers are empty (TXEx = 1, transmitted successfully or
aborted) and then goes into Sleep Mode
•
If it is receiving, it continues to receive and goes into Sleep Mode
as soon as the CAN bus next becomes idle
•
If it is neither transmitting nor receiving, it will immediately go into
Sleep Mode
The application software must avoid setting up a transmission (by
clearing one or more TXE flag(s)) and immediately request Sleep Mode
(by setting SLPRQ). It then depends on the exact sequence of
operations whether the msCAN12 starts transmitting or goes into Sleep
Mode directly.
During Sleep Mode, the SLPAK flag is set. The application software
should use SLPAK as a handshake indication for the request (SLPRQ)
to go into Sleep Mode. When in Sleep Mode, the msCAN12 stops its
internal clocks. However, clocks to allow register accesses still run. If the
msCAN12 is in bus-off state, it stops counting the 128*11 consecutive
recessive bits due to the stopped clock. The TxCAN pin stays in
recessive state. If RXF=1, the message can be read and RXF can be
cleared. Copying of RxBG into RxFG does not take place while in Sleep
Mode. It is possible to access the transmit buffers and to clear the TXE
flags. No message abort takes place while in sleep mode.
The msCAN12 leaves Sleep mode (wake-up) when
•
bus activity occurs or
•
the MCU clears the SLPRQ bit or
•
the MCU sets SFTRES.
Technical Data
326
MC68HC912DG128 — Rev 3.0
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN Controller
Low Power Modes
NOTE:
The MCU cannot clear the SLPRQ bit before the msCAN12 is in Sleep
Mode (SLPAK = 1).
Freescale Semiconductor, Inc...
After wake-up, the msCAN12 waits for 11 consecutive recessive bits to
synchronize to the bus. As a consequence, if the msCAN12 is woken-up
by a CAN frame, this frame is not received. The receive message buffers
(RxBG and RxFG) contain messages if they were received before sleep
mode was entered. All pending actions are executed upon wake-up:
copying of RxBG into RxFG, message aborts and message
transmissions. If the msCAN12 is still in bus-off state after leaving Sleep
Mode, it continues counting the 128*11 consecutive recessive bits.
msCAN12 Running
SLPRQ = 0
SLPAK = 0
MCU
MCU
or msCAN12
msCAN12 Sleeping
SLEEP Request
SLPRQ = 1
SLPAK = 1
SLPRQ = 1
SLPAK = 0
msCAN12
Figure 17-6. SLEEP Request / Acknowledge Cycle
17.8.2 msCAN12 SOFT_RESET Mode
In SOFT_RESET mode, the msCAN12 is stopped. Registers can still be
accessed. This mode is used to initialize the module configuration, bit
timing, and the CAN message filter. See msCAN12 Module Control
Register 0 (CMCR0) for a complete description of the SOFT_RESET
mode.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
327
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
NOTE:
When setting the SFTRES bit, the msCAN12 immediately stops all
ongoing transmissions and receptions, potentially causing the CAN
protocol violations. The user is responsiblefor ensuring that the
msCAN12 is not active when SOFT_RESET mode is entered. The
recommended procedure is to bring the msCAN12 into SLEEP mode
before the SFTRES bit is set.
17.8.3 msCAN12 POWER_DOWN Mode
The msCAN12 is in POWER_DOWN mode when
•
the CPU is in STOP mode or
•
the CPU is in WAIT mode and the CSWAI bit is set (see msCAN12
Module Control Register 0 (CMCR0)).
When entering the POWER_DOWN mode, the msCAN12 immediately
stops all ongoing transmissions and receptions, potentially causing CAN
protocol violations.
NOTE:
The user is responsible to take care that the msCAN12 is not active
when POWER_DOWN mode is entered. The recommended procedure
is to bring the msCAN12 into SLEEP mode before the STOP instruction
(or the WAI instruction, if CSWAI is set) is executed.
To protect the CAN bus system from fatal consequences of violations to
the above rule, the msCAN12 drives the TxCAN pin into recessive state.
In POWER_DOWN mode, no registers can be accessed.
17.8.4 Programmable Wake-Up Function
The msCAN12 can be programmed to apply a low-pass filter function to
the RxCAN input line while in SLEEP mode (see control bit WUPM in the
module control register, msCAN12 Module Control Register 0
(CMCR0)). This feature can be used to protect the msCAN12 from
wake-up due to short glitches on the CAN bus lines. Such glitches can
result from electromagnetic interference within noisy environments.
Technical Data
328
MC68HC912DG128 — Rev 3.0
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
Timer Link
17.9 Timer Link
The msCAN12 generates a timer signal whenever a valid frame has
been received. Because the CAN specification defines a frame to be
valid if no errors occurred before the EOF field has been transmitted
successfully, the timer signal is generated right after the EOF. A pulse of
one bit time is generated. As the msCAN12 receiver engine also
receives the frames being sent by itself, a timer signal is also generated
after a successful transmission.
The previously described timer signal can be routed into the on-chip
timer interface module (ECT). This signal is connected to the Timer n
Channel input under the control of the timer link enable (TLNKEN) bit in
the CMCR0(1).
After timer n has been programmed to capture rising edge events, it can
be used under software control to generate 16-bit time stamps which can
be stored with the received message.
17.10 Clock System
Figure 17-7 shows the structure of the msCAN12 clock generation
circuitry. With this flexible clocking scheme the msCAN12 is able to
handle CAN bus rates ranging from 10 kbps up to 1 Mbps.
CGM
msCAN12
SYSCLK
CGMCANCLK
CLKSRC
EXTALi
Prescaler
(1...64)
Time quanta
clock
CLKSRC
Figure 17-7. Clocking Scheme
1. The timer channel being used for the timer link for CAN0 is channel 4 and for CAN1 is channel
5.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
329
Freescale Semiconductor, Inc.
MSCAN Controller
The clock source bit (CLKSRC) in the msCAN12 module control register
(CMCR1) (see msCAN12 Bus Timing Register 0 (CBTR0)) defines
whether the msCAN12 is connected to the output of the crystal oscillator
(EXTALi) or to a clock twice as fast as the system clock (ECLK).
The clock source has to be chosen such that the tight oscillator tolerance
requirements (up to 0.4%) of the CAN protocol are met. Additionally, for
high CAN bus rates (1 Mbps), a 50% duty cycle of the clock is required.
Freescale Semiconductor, Inc...
NOTE:
If the system clock is generated from a PLL, it is recommended to select
the crystal clock source rather than the system clock source due to jitter
considerations, especially at faster CAN bus rates.
For microcontrollers without the CGM module, CGMCANCLK is driven
from the crystal oscillator (EXTALi).
A programmable prescaler is used to generate out of msCANCLK the
time quanta (Tq) clock. A time quantum is the atomic unit of time handled
by the msCAN12.
A bit time is subdivided
f CGMCANCLK
f Tq = ------------------------------------------Presc ⋅ value
into three segments(1):
•
SYNC_SEG: This segment has a fixed length of one time
quantum. Signal edges are expected to happen within this section.
•
Time segment 1: This segment includes the PROP_SEG and the
PHASE_SEG1 of the CAN standard. It can be programmed by
setting the parameter TSEG1 to consist of 4 to 16 time quanta.
•
Time segment 2: This segment represents the PHASE_SEG2 of
the CAN standard. It can be programmed by setting the TSEG2
parameter to be 2 to 8 time quanta long.
The synchronization jump width can be programmed in a range of 1 to 4
time quanta by setting the SJW parameter.
1. For further explanation of the under-lying concepts please refer to ISO/DIS 11519-1, Section
10.3.
Technical Data
330
MC68HC912DG128 — Rev 3.0
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN Controller
Clock System
The above parameters can be set by programming the bus timing
registers (CBTR0–1, see msCAN12 Bus Timing Register 0 (CBTR0) and
msCAN12 Bus Timing Register 1 (CBTR1)).
NOTE:
It is the user’s responsibility to make sure that his bit time settings are in
compliance with the CAN standard. Figure 17-9 gives an overview on
the CAN conforming segment settings and the related parameter values.
Freescale Semiconductor, Inc...
NRZ Signal
SYNC
_SEG
Time segment 1
(PROP_SEG + PHASE_SEG1)
Time Seg. 2
(PHASE_SEG2)
1
4 ... 16
2 ... 8
8... 25 Time Quanta
= 1 Bit Time
Transmit point
Sample point
(single or triple sampling)
Figure 17-8. Segments within the Bit Time
Figure 17-9. CAN Standard Compliant Bit Time Segment Settings
Time Segment 1
TSEG1
Time Segment 2
TSEG2
5 .. 10
4 .. 11
5 .. 12
6 .. 13
7 .. 14
8 .. 15
9 .. 16
4 .. 9
3 .. 10
4 .. 11
5 .. 12
6 .. 13
7 .. 14
8 .. 15
2
3
4
5
6
7
8
1
2
3
4
5
6
7
MC68HC912DG128 — Rev 3.0
MOTOROLA
Synchron.
Jump Width
1 .. 2
1 .. 3
1 .. 4
1 .. 4
1 .. 4
1 .. 4
1 .. 4
SJW
0 .. 1
0 .. 2
0 .. 3
0 .. 3
0 .. 3
0 .. 3
0 .. 3
Technical Data
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
331
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
17.11 Memory Map
The msCAN12 occupies 128 bytes in the CPU12 memory space. The
background receive buffer can only be read in test mode.
Figure 17-10. msCAN12 Memory Map
$0100
$0108
$0109
$010D
$010E
$010F
$0110
$011F
$0120
$013C
$013D
$013F
$0140
$014F
$0150
$015F
$0160
$016F
$0170
$017F
Control registers
9 bytes
Reserved
5 bytes
Error counters
2 bytes
Identifier filter
16 bytes
Reserved
29 bytes
Port CAN registers
3 bytes
Foreground Receive buffer
Transmit buffer 0
Transmit buffer 1
Transmit buffer 2
17.12 Programmer’s Model of Message Storage
The following section details the organisation of the receive and transmit
message buffers and the associated control registers. For reasons of
programmer interface simplification the receive and transmit message
buffers have the same outline. Each message buffer allocates 16 bytes
in the memory map containing a 13 byte data structure. An additional
transmit buffer priority register (TBPR) is defined for the transmit buffers.
Technical Data
332
MC68HC912DG128 — Rev 3.0
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
Programmer’s Model of Message Storage
Figure 17-11. Message Buffer Organization
Address
(1)
Register name
01x0
Identifier register 0
01x1
01x2
01x3
01x4
01x5
01x6
01x7
01x8
01x9
01xA
01xB
01xC
Identifier register 1
Identifier register 2
Identifier register 3
Data segment register 0
Data segment register 1
Data segment register 2
Data segment register 3
Data segment register 4
Data segment register 5
Data segment register 6
Data segment register 7
Data length register
01xD
Transmit buffer priority register(2)
Unused
Unused
01xE
01xF
1. x is 4, 5, 6, or 7 depending on which buffer RxFG,
Tx0, Tx1, or Tx2 respectively.
2. Not applicable for receive buffers
17.12.1 Message Buffer Outline
Figure 17-12 shows the common 13 byte data structure of receive and
transmit buffers for extended identifiers. The mapping of standard
identifiers into the IDR registers is shown in Figure 17-13. All bits of the
13 byte data structure are undefined out of reset.
NOTE:
The foreground receive buffer can be read anytime but cannot be
written. The transmit buffers can be read or written anytime.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
333
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
Figure 17-12. Receive/Transmit Message Buffer Extended Identifier
ADDR(1)
REGISTER
$01x0
IDR0
$01x1
IDR1
$01x2
IDR2
$01x3
IDR3
$01x4
DSR0
$01x5
DSR1
$01x6
DSR2
$01x7
DSR3
$01x8
DSR4
$01x9
DSR5
$01xA
DSR6
$01xB
DSR7
$01xC
DLR
R/W
R
W
R
W
R
W
R
W
R
W
R
W
R
W
R
W
R
W
R
W
R
W
R
W
R
W
BIT 7
6
5
4
3
2
1
BIT 0
ID28
ID27
ID26
ID25
ID24
ID23
ID22
ID21
ID20
ID19
ID18
ID17
ID16
ID15
ID14
ID13
ID12
ID11
ID10
ID9
ID8
ID7
ID6
ID5
ID4
ID3
ID2
ID1
ID0
RTR
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
DLC3
DLC2
DLC1
DLC0
SRR (1) IDE (1)
1. x is 4, 5, 6, or 7 depending on which buffer RxFG, Tx0, Tx1, or Tx2 respectively.
Technical Data
334
MC68HC912DG128 — Rev 3.0
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
Programmer’s Model of Message Storage
Figure 17-13. Standard Identifier Mapping
ADDR(1)
REGISTER
$01x0
IDR0
$01x1
IDR1
$01x2
IDR2
$01x3
IDR3
R/W
R
W
R
W
R
W
R
W
BIT 7
6
5
4
3
2
1
BIT 0
ID10
ID9
ID8
ID7
ID6
ID5
ID4
ID3
ID2
ID1
ID0
RTR
IDE(0)
1. x is 4, 5, 6, or 7 depending on which buffer RxFG, Tx0, Tx1, or Tx2 respectively.
17.12.2 Identifier Registers (IDRn)
The identifiers consist of either 11 bits (ID10–ID0) for the standard, or 29
bits (ID28–ID0) for the extended format. ID10/28 is the most significant
bit and is transmitted first on the bus during the arbitration procedure.
The priority of an identifier is defined to be highest for the smallest binary
number.
SRR — Substitute Remote Request
This fixed recessive bit is used only in extended format. It must be set
to 1 by the user for transmission buffers and will be stored as received
on the CAN bus for receive buffers.
IDE — ID Extended
This flag indicates whether the extended or standard identifier format
is applied in this buffer. In the case of a receive buffer the flag is set
as being received and indicates to the CPU how to process the buffer
identifier registers. In the case of a transmit buffer the flag indicates to
the msCAN12 what type of identifier to send.
0 = Standard format (11-bit)
1 = Extended format (29-bit)
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
335
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
RTR — Remote transmission request
This flag reflects the status of the Remote Transmission Request bit
in the CAN frame. In the case of a receive buffer it indicates the status
of the received frame and supports the transmission of an answering
frame in software. In the case of a transmit buffer, this flag defines the
setting of the RTR bit to be sent.
0 = Data frame
1 = Remote frame
17.12.3 Data Length Register (DLR)
This register keeps the data length field of the CAN frame.
DLC3 – DLC0 — Data length code bits
The data length code contains the number of bytes (data byte count)
of the respective message. At the transmission of a remote frame, the
data length code is transmitted as programmed while the number of
transmitted data bytes is always 0. The data byte count ranges from
0 to 8 for a data frame. Table 17-3 shows the effect of setting the DLC
bits.
Table 17-3. Data length codes
Data length code
DLC3
DLC2
DLC1
DLC0
0
0
0
0
0
0
0
0
1
0
0
0
0
1
1
1
1
0
0
0
1
1
0
0
1
1
0
0
1
0
1
0
1
0
1
0
Technical Data
336
Data
byte
count
0
1
2
3
4
5
6
7
8
MC68HC912DG128 — Rev 3.0
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
Programmer’s Model of Message Storage
17.12.4 Data Segment Registers (DSRn)
The eight data segment registers contain the data to be transmitted or
being received. The number of bytes to be transmitted or being received
is determined by the data length code in the corresponding DLR.
17.12.5 Transmit Buffer Priority Registers (TBPR)
BIT 7
BIT 6
BIT 5
BIT 4
BIT 3
BIT 2
BIT 1
BIT 0
PRIO7
PRIO6
PRIO5
PRIO4
PRIO3
PRIO2
PRIO1
PRIO0
-
-
-
-
-
-
-
-
(1)
R
TBPR
$01xD
W
RESET
1. x is 5, 6, or 7 depending on which buffer Tx0, Tx1, or Tx2 respectively.
PRIO7 – PRIO0 — Local Priority
This field defines the local priority of the associated message buffer.
The local priority is used for the internal prioritisation process of the
msCAN12 and is defined to be highest for the smallest binary number.
The msCAN12 implements the following internal prioritisation
mechanism:
NOTE:
•
All transmission buffers with a cleared TXE flag participate in the
prioritisation immediately before the SOF (Start of Frame) is sent.
•
The transmission buffer with the lowest local priority field wins the
prioritisation.
•
In cases of more than one buffer having the same lowest priority,
the message buffer with the lower index number wins.
To ensure data integrity, no registers of the transmit buffers shall be
written while the associated TXE flag is cleared.
To ensure data integrity, no registers of the receive buffer shall be read
while the RXF flag is cleared.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
337
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
17.13 Programmer’s Model of Control Registers
17.13.1 Overview
The programmer’s model has been laid out for maximum simplicity and
efficiency.
17.13.2 msCAN12 Module Control Register 0 (CMCR0)
CMCR0
R
$0100
W
RESET
Bit 7
0
6
0
0
0
5
CSWAI
1
4
SYNCH
3
TLNKEN
0
2
SLPAK
0
0
1
Bit 0
SLPRQ
SFTRES
0
1
CSWAI — CAN Stops in Wait Mode
0 = The module is not affected during WAIT mode.
1 = The module ceases to be clocked during WAIT mode.
SYNCH — Synchronized Status
This bit indicates whether the msCAN12 is synchronized to the CAN
bus and as such can participate in the communication process.
0 = msCAN12 is not synchronized to the CAN bus
1 = msCAN12 is synchronized to the CAN bus
TLNKEN — Timer Enable
This flag is used to establish a link between the msCAN12 and the onchip timer (see Timer Link).
0 = The port is connected to the timer input.
1 = The msCAN12 timer signal output is connected to the timer
input.
SLPAK — SLEEP Mode Acknowledge
This flag indicates whether the msCAN12 is in module internal
SLEEP Mode. It shall be used as a handshake for the SLEEP Mode
request (see msCAN12 SLEEP Mode).
0 = Wake-up – The msCAN12 is not in SLEEP Mode.
1 = SLEEP – The msCAN12 is in SLEEP Mode.
Technical Data
338
MC68HC912DG128 — Rev 3.0
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN Controller
Programmer’s Model of Control Registers
SLPRQ — SLEEP request
This flag allows to request the msCAN12 to go into an internal powersaving mode (see msCAN12 SLEEP Mode).
0 = Wake-up – The msCAN12 will function normally.
1 = SLEEP request – The msCAN12 will go into SLEEP Mode
when the CAN bus is idle, i.e. the module is not receiving a
message and all transmit buffers are empty.
SFTRES— SOFT_RESET
Freescale Semiconductor, Inc...
When this bit is set by the CPU, the msCAN12 immediately enters the
SOFT_RESET state. Any ongoing transmission or reception is
aborted and synchronisation to the bus is lost.
The following registers will go into and stay in the same state as out
of hard reset: CMCR0, CRFLG, CRIER, CTFLG, CTCR.
The registers CMCR1, CBTR0, CBTR1, CIDAC, CIDAR0–3,
CIDMR0–3 can only be written by the CPU when the msCAN12 is in
SOFT_RESET state. The values of the error counters are not affected
by SOFT_RESET.
When this bit is cleared by the CPU, the msCAN12 will try to
synchronize to the CAN bus: If the msCAN12 is not in BUSOFF state
it will be synchronized after 11 recessive bits on the bus; if the
msCAN12 is in BUSOFF state it continues to wait for 128 occurrences
of 11 recessive bits.
Clearing SFTRES and writing to other bits in CMCR0 must be in
separate instructions.
0 = Normal operation
1 = msCAN12 in SOFT_RESET state.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
339
Freescale Semiconductor, Inc.
MSCAN Controller
17.13.3 msCAN12 Module Control Register (CMCR1)
CMCR1
R
$0101
W
RESET
Bit 7
0
6
0
5
0
4
0
3
0
0
0
0
0
0
2
1
Bit 0
LOOPB
WUPM
CLKSRC
0
0
0
LOOPB — Loop Back Self Test Mode
Freescale Semiconductor, Inc...
When this bit is set the msCAN12 performs an internal loop back which
can be used for self test operation: the bit stream output of the
transmitter is fed back to the receiver internally. The RxCAN input pin
is ignored and the TxCAN output goes to the recessive state (1). The
msCAN12 behaves as it normally does while transmitting and treats its
own transmitted message as a message received from a remote node.
In this state the msCAN12 ignores the bit sent during the ACK slot of
the CAN frame Acknowledge field to ensure proper reception of its
own message. Both transmit and receive interrupts are generated.
0 = Normal operation
1 = Activate loop back self test mode
WUPM — Wake-Up Mode
This flag defines whether the integrated low-pass filter is applied to
protect the msCAN12 from spurious wake-ups (see Programmable
Wake-Up Function).
0 = msCAN12 will wake up the CPU after any recessive to
dominant edge on the CAN bus.
1 = msCAN12 will wake up the CPU only in the case of dominant
pulse on the bus which has a length of at least approximately
Twup.
CLKSRC — msCAN12 Clock Source
This flag defines which clock source the msCAN12 module is driven
from (only for system with CGM module; see Clock System, Figure
17-7).
0 = The msCAN12 clock source is EXTALi.
1 = The msCAN12 clock source is SYSCLK, twice the frequency of
ECLK.
NOTE:
The CMCR1 register can be written only if the SFTRES bit in CMCR0 is
set.
Technical Data
340
MC68HC912DG128 — Rev 3.0
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN Controller
Programmer’s Model of Control Registers
17.13.4 msCAN12 Bus Timing Register 0 (CBTR0)
CBTR0
R
$0102
W
RESET
Bit 7
6
5
4
3
2
1
Bit 0
SJW1
SJW0
BRP5
BRP4
BRP3
BRP2
BRP1
BRP0
0
0
0
0
0
0
0
0
SJW1, SJW0 — Synchronization Jump Width
Freescale Semiconductor, Inc...
The synchronization jump width defines the maximum number of time
quanta (Tq) clock cycles by which a bit may be shortened, or
lengthened, to achieve resynchronization on data transitions on the
bus (see Table 17-4).
Table 17-4. Synchronization jump width
SJW1
0
0
1
1
SJW0
0
1
0
1
Synchronization jump width
1 Tq clock cycle
2 Tq clock cycles
3 Tq clock cycles
4 Tq clock cycles
BRP5 – BRP0 — Baud Rate Prescaler
These bits determine the time quanta (Tq) clock, which is used to
build up the individual bit timing, according to Table 17-5.
Table 17-5. Baud rate prescaler
BRP5
0
0
0
0
:
:
1
NOTE:
BRP4
0
0
0
0
:
:
1
BRP3
0
0
0
0
:
:
1
BRP2
0
0
0
0
:
:
1
BRP1
0
0
1
1
:
:
1
BRP0
0
1
0
1
:
:
1
The CBTR0 register can only be written if the SFTRES bit in CMCR0 is
set.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Prescaler value (P)
1
2
3
4
:
:
64
Technical Data
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
341
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
17.13.5 msCAN12 Bus Timing Register 1 (CBTR1)
CBTR1
R
$0103
W
RESET
Bit 7
6
5
4
3
2
1
Bit 0
SAMP
TSEG22
TSEG21
TSEG20
TSEG13
TSEG12
TSEG11
TSEG10
0
0
0
0
0
0
0
0
SAMP — Sampling
This bit determines the number of samples of the serial bus to be
taken per bit time. If set three samples per bit are taken, the regular
one (sample point) and two preceding samples, using a majority rule.
For higher bit rates SAMP should be cleared, which means that only
one sample will be taken per bit.
0 = One sample per bit.
1 = Three samples per bit(1).
TSEG22 – TSEG10 — Time Segment
Time segments within the bit time fix the number of clock cycles per
bit time, and the location of the sample point.
Table 17-6. Time segment syntax
SYNC_SEG
Transmit point
Sample point
System expects transitions to occur on the bus during this period.
A node in transmit mode will transfer a new value to the CAN bus at this point.
A node in receive mode will sample the bus at this point. If the three samples per bit option is
selected then this point marks the position of the third sample.
Time segment 1 (TSEG1) and time segment 2 (TSEG2) are
programmable as shown in Table 17-7.
Table 17-7. Time segment values
TSEG13 TSEG12 TSEG11 TSEG10 Time segment 1
0
0
0
0
1 Tq clock cycle
0
0
0
1
2 Tq clock cycles
0
0
1
0
3 Tq clock cycles
0
0
1
1
4 Tq clock cycles
.
.
.
.
.
.
.
.
.
.
1
1
1
1
16 Tq clock cycles
TSEG22 TSEG21 TSEG20 Time segment 2
0
0
0
1 Tq clock cycle
0
0
1
2 Tq clock cycles
.
.
.
.
.
.
.
.
1
1
1
8 Tq clock cycles
1. In this case, PHASE_SEG1 must be at least two time quanta.
Technical Data
342
MC68HC912DG128 — Rev 3.0
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
Programmer’s Model of Control Registers
The bit time is determined by the oscillator frequency, the baud rate
prescaler, and the number of time quanta (Tq) clock cycles per bit (as
shown above).
Presc ⋅ value
BitTime = ------------------------------------------- • number Þ of Þ TimeQuanta
f CGMCANCLK
NOTE:
The CBTR1 register can only be written if the SFTRES bit in CMCR0 is
set.
17.13.6 msCAN12 Receiver Flag Register (CRFLG)
All bits of this register are read and clear only. A flag can be cleared by
writing a 1 to the corresponding bit position. A flag can only be cleared
when the condition which caused the setting is no more valid. Writing a
0 has no effect on the flag setting. Every flag has an associated interrupt
enable flag in the CRIER register. A hard or soft reset clears the register.
CRFLG
R
$0104
W
RESET
Bit 7
6
5
4
3
2
1
Bit 0
WUPIF
RWRNIF
TWRNIF
RERRIF
TERRIF
BOFFIF
OVRIF
RXF
0
0
0
0
0
0
0
0
WUPIF — Wake-up Interrupt Flag
If the msCAN12 detects bus activity while in SLEEP Mode, it sets the
WUPIFflag. If not masked, a Wake-Up interrupt is pending while this
flag is set.
0 = No wake-up activity has been observed while in SLEEP Mode.
1 = msCAN12 has detected activity on the bus and requested
wake-up.
RWRNIF — Receiver Warning Interrupt Flag
This flag is set when the msCAN12 goes into warning status due to
the Receive Error counter (REC) exceeding 96 and neither one of the
Error interrupt flags or the Bus-Off interrupt flag is set(1). If not
masked, an Error interrupt is pending while this flag is set.
0 = No receiver warning status has been reached.
1 = msCAN12 went into receiver warning status.
1. Condition to set the flag: RWRNIF = (96 < REC ≤ 127) & RERRIF& TERRIF & BOFFIF
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
343
Freescale Semiconductor, Inc.
MSCAN Controller
TWRNIF — Transmitter Warning Interrupt Flag
This flag is set when the msCAN12 goes into warning status due to
the Transmit Error counter (TEC) exceeding 96 and neither one of the
Error interrupt flags or the Bus-Off interrupt flag is set(1). If not
masked, an Error interrupt is pending while this flag is set.
0 = No transmitter warning status has been reached.
1 = msCAN12 went into transmitter warning status.
RERRIF — Receiver Error Passive Interrupt Flag
Freescale Semiconductor, Inc...
This flag is set when the msCAN12 goes into error passive status due
to the Receive Error counter (REC) exceeding 127 and the Bus-Off
interrupt flag is not set(2). If not masked, an Error interrupt is pending
while this flag is set.
0 = No receiver error passive status has been reached.
1 = msCAN12 went into receiver error passive status.
TERRIF — Transmitter Error Passive Interrupt Flag
This flag is set when the msCAN12 goes into error passive status due
to the Transmit Error counter (TEC) exceeding 127 and the Bus-Off
interrupt flag is not set(3). If not masked, an Error interrupt is pending
while this flag is set.
0 = No transmitter error passive status has been reached.
1 = msCAN12 went into transmitter error passive status.
BOFFIF — BUSOFF Interrupt Flag
This flag is set when the msCAN12 goes into BUSOFF status, due to
the Transmit Error counter exceeding 255. It cannot be cleared before
the msCAN12 has monitored 128 times 11 consecutive recessive bits
on the bus. If not masked, an Error interrupt is pending while this flag
is set.
0 = No BUSOFF status has been reached.
1 = msCAN12 went into BUSOFF status.
1. Condition to set the flag: TWRNIF = (96 < TEC ≤ 127) & RERRIF& TERRIF & BOFFIF
2. Condition to set the flag: RERRIF = (128 < REC < 255) & BOFFIF
3. Condition to set the flag: TERRIF = (128 < TEC < 255) & BOFFIF
Technical Data
344
MC68HC912DG128 — Rev 3.0
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
Programmer’s Model of Control Registers
OVRIF — Overrun Interrupt Flag
This flag is set when a data overrun condition occurs. If not masked,
an Error interrupt is pending while this flag is set.
0 = No data overrun has occurred.
1 = A data overrun has been detected.
RXF — Receive Buffer Full
The RXF flag is set by the msCAN12 when a new message is
available in the foreground receive buffer. This flag indicates whether
the buffer is loaded with a correctly received message. After the CPU
has read that message from the receive buffer the RXF flag must be
handshaken (cleared) in order to release the buffer. A set RXF flag
prohibits the exchange of the background receive buffer into the
foreground buffer. If not masked, a Receive interrupt is pending while
this flag is set.
0 = The receive buffer is released (not full).
1 = The receive buffer is full. A new message is available.
WARNING:
NOTE:
To ensure data integrity, no registers of the receive buffer shall be read
while the RXF flag is cleared.
The CRFLG register is held in the reset state when the SFTRES bit in
CMCR0 is set.
17.13.7 msCAN12 Receiver Interrupt Enable Register (CRIER)
CRIER
R
$0105
W
RESET
Bit 7
6
5
4
3
2
1
Bit 0
WUPIE
RWRNIE
TWRNIE
RERRIE
TERRIE
BOFFIE
OVRIE
RXFIE
0
0
0
0
0
0
0
0
WUPIE — Wake-up Interrupt Enable
0 = No interruptis generated from this event.
1 = A wake-up event results in a wake-up interrupt.
RWRNIE — Receiver Warning Interrupt Enable
0 = No interruptis generated from this event.
1 = A receiver warning status event results in an error interrupt.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
345
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
TWRNIE — Transmitter Warning Interrupt Enable
0 = No interruptis generated from this event.
1 = A transmitter warning status event results in an error interrupt.
RERRIE — Receiver Error Passive Interrupt Enable
0 = No interruptis generated from this event.
1 = A receiver error passive status event results in an error
interrupt.
TERRIE — Transmitter Error Passive Interrupt Enable
0 = No interruptis generated from this event.
1 = A transmitter error passive status event results in an error
interrupt.
BOFFIE — BUSOFF Interrupt Enable
0 = No interruptis generated from this event.
1 = A BUSOFF event results in an error interrupt.
OVRIE — Overrun Interrupt Enable
0 = No interruptis generated from this event.
1 = An overrun event results in an error interrupt.
RXFIE — Receiver Full Interrupt Enable
0 = No interruptis generated from this event.
1 = A receive buffer full (successful message reception) event
results in a receive interrupt.
NOTE:
The CRIER register is held in the reset state when the SFTRES bit in
CMCR0 is set.
17.13.8 msCAN12 Transmitter Flag Register (CTFLG)
The Abort Acknowledge flags are read only. The Transmitter Buffer
Empty flags are read and clear only. A flag can be cleared by writing a1
to the corresponding bit position. Writing a zero has no effect on the flag
setting. The Transmitter Buffer Empty flags each have an associated
Technical Data
346
MC68HC912DG128 — Rev 3.0
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN Controller
Programmer’s Model of Control Registers
interrupt enable flag in the CTCR register. A hard or soft reset will reset
the register.
CTFLG
R
$0106
W
RESET
Bit 7
0
6
ABTAK2
5
ABTAK1
4
ABTAK0
3
0
0
0
0
0
0
2
1
Bit 0
TXE2
TXE1
TXE0
1
1
1
ABTAK2 – ABTAK0 — Abort Acknowledge
Freescale Semiconductor, Inc...
This flag acknowledges that a message has been aborted due to a
pending abort request from the CPU. After a particular message
buffer has been flagged empty, this flag can be used by the
application software to identify whether the message has been
aborted successfully or has been sent in the meantime. The ABTAKx
flag is cleared implicitly whenever the corresponding TXE flag is
cleared.
0 = The massage has not been aborted, thus has been sent out.
1 = The message has been aborted.
TXE2 – TXE0 —Transmitter Buffer Empty
This flag indicates that the associated transmit message buffer is
empty, thus not scheduled for transmission. The CPU must
handshake (clear) the flag after a message has been set up in the
transmit buffer and is due for transmission. The msCAN12 sets the
flag after the message has been sent successfully. The flag is also set
by the msCAN12 when the transmission request was successfully
aborted due to a pending abort request (msCAN12 Transmitter
Control Register (CTCR)). If not masked, a transmit interrupt is
pending while this flag is set.
Clearing a TXEx flag also clears the corresponding ABTAKx flag (see
above). When a TXEx flag is set, the corresponding ABTRQx bit is
cleared (see msCAN12 Transmitter Control Register (CTCR)).
0 = The associated message buffer is full (loaded with a message
due for transmission).
1 = The associated message buffer is empty (not scheduled).
WARNING:
To ensure data integrity, no registers of the transmit buffers should be written
to while the associated TXE flag is cleared.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
347
Freescale Semiconductor, Inc.
MSCAN Controller
NOTE:
The CTFLG register is held in the reset state if the SFTRES bit in
CMCR0 is set.
17.13.9 msCAN12 Transmitter Control Register (CTCR)
CTCR
R
$0107
W
RESET
Bit 7
0
0
6
5
4
ABTRQ2
ABTRQ1
ABTRQ0
0
0
0
3
0
2
1
Bit 0
TXEIE2
TXEIE1
TXEIE0
0
0
0
0
Freescale Semiconductor, Inc...
ABTRQ2 – ABTRQ0 — Abort Request
The CPU sets an ABTRQx bit to request that a scheduled message
buffer (TXEx = 0) shall be aborted. The msCAN12 grants the request
if the message has not already started transmission or if the
transmission is not successful (lost arbitration or error). When a
message is aborted, the associated TXE and the Abort Acknowledge
flag (ABTAK, see msCAN12 Transmitter Flag Register (CTFLG)) are
set and an TXE interrupt is generated if enabled. The CPU cannot
reset ABTRQx. ABTRQx is cleared implicitly whenever the
associated TXE flag is set.
0 = No abort request.
1 = Abort request pending.
NOTE:
The software must not clear one or more of the TXE flags in CTFGL and
simultaneously set the respective ABTRQ bit(s).
TXEIE2 – TXEIE0 — Transmitter Empty Interrupt Enable
0 = No interruptis generated from this event.
1 = A transmitter empty (transmit buffer available for transmission)
event results in a transmitter empty interrupt.
NOTE:
The CTCR register is held in the reset state when the SFTRES bit in
CMCR0 is set.
Technical Data
348
MC68HC912DG128 — Rev 3.0
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
MSCAN Controller
Programmer’s Model of Control Registers
17.13.10 msCAN12 Identifier Acceptance Control Register (CIDAC)
CIDAC
R
$0108
W
RESET
Bit 7
0
6
0
0
0
5
4
IDAM1
IDAM0
0
0
3
0
2
IDHIT2
1
IDHIT1
Bit 0
IDHIT0
0
0
0
0
IDAM1 – IDAM0 — Identifier Acceptance Mode
Freescale Semiconductor, Inc...
The CPU sets these flags to define the identifier acceptance filter
organisation (see Identifier Acceptance Filter). Table 17-7
summarizes the different settings. In Filter Closed mode no
messages are accepted such that the foreground buffer is never
reloaded.
Table 17-8. Identifier Acceptance Mode Settings
IDAM1
0
0
1
1
IDAM0
0
1
0
1
Identifier Acceptance Mode
Two 32 bit Acceptance Filters
Four 16 bit Acceptance Filters
Eight 8 bit Acceptance Filters
Filter Closed
IDHIT2 – IDHIT0 — Identifier Acceptance Hit Indicator
The msCAN12 sets these flags to indicate an identifier acceptance hit
(see Identifier Acceptance Filter). Table 17-7 summarizes the
different settings.
Table 17-9. Identifier Acceptance Hit Indication
IDHIT2
0
0
0
0
1
1
1
1
IDHIT1
0
0
1
1
0
0
1
1
IDHIT0
0
1
0
1
0
1
0
1
Identifier Acceptance Hit
Filter 0 Hit
Filter 1 Hit
Filter 2 Hit
Filter 3 Hit
Filter 4 Hit
Filter 5 Hit
Filter 6 Hit
Filter 7 Hit
The IDHIT indicators are always related to the message in the
foreground buffer. When a message gets copied from the background to
the foreground buffer the indicators are updated as well.
NOTE:
The CIDAC register can only be written if the SFTRES bit in CMCR0 is
set.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
349
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
17.13.11 msCAN12 Receive Error Counter (CRXERR)
CRXERR R
$010E
W
RESET
Bit 7
RXERR7
6
RXERR6
5
RXERR5
4
RXERR4
3
RXERR3
2
RXERR2
1
RXERR1
Bit 0
RXERR0
0
0
0
0
0
0
0
0
This register reflects the status of the msCAN12 receive error counter.
The register is read only.
17.13.12 msCAN12 Transmit Error Counter (CTXERR)
CTXERR R
$010F
W
RESET
Bit 7
TXERR7
6
TXERR6
5
TXERR5
4
TXERR4
3
TXERR3
2
TXERR2
1
TXERR1
Bit 0
TXERR0
0
0
0
0
0
0
0
0
This register reflects the status of the msCAN12 transmit error counter.
The register is read only.
NOTE:
Both error counters must only be read when in SLEEP or SOFT_RESET
mode.
17.13.13 msCAN12 Identifier Acceptance Registers (CIDAR0–7)
On reception each message is written into the background receive
buffer. The CPU is only signalled to read the message however, if it
passes the criteria in the identifier acceptance and identifier mask
registers (accepted); otherwise, the message is overwritten by the next
message (dropped).
The acceptance registers of the msCAN12 are applied on the IDR0 to
IDR3 registers of incoming messages in a bit by bit manner.
For extended identifiers all four acceptance and mask registers are
applied. For standard identifiers only the first two (CIDMR0/1 and
CIDAR0/1) are applied. In the latter case it is required to program the
three last bits (AM2 – AM0) in the mask register CIDMR1 to ‘don’t care’.
Technical Data
350
MC68HC912DG128 — Rev 3.0
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
Programmer’s Model of Control Registers
Figure 17-14. Identifier Acceptance Registers (1st bank)
CIDAR0
$0110
CIDAR1
$0111
CIDAR2
$0112
CIDAR3
$0113
RESET
R
W
R
W
R
W
R
W
Bit 7
6
5
4
3
2
1
Bit 0
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
-
-
-
-
-
-
-
-
Figure 17-15. Identifier Acceptance Registers (2nd bank)
CIDAR4
$0118
CIDAR5
$0119
CIDAR6
$011A
CIDAR7
$011B
RESET
R
W
R
W
R
W
R
W
Bit 7
6
5
4
3
2
1
Bit 0
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
AC7
AC6
AC5
AC4
AC3
AC2
AC1
AC0
-
-
-
-
-
-
-
-
AC7 – AC0 — Acceptance Code Bits
AC7 – AC0 comprise a user defined sequence of bits with which the
corresponding bits of the related identifier register (IDRn) of the
receive message buffer are compared. The result of this comparison
is then masked with the corresponding identifier mask register.
NOTE:
The CIDAR0–7 registers can only be written if the SFTRES bit in
CMCR0 is set.
17.13.14 msCAN12 Identifier Mask Registers (CIDMR0–7)
The identifier mask register specifies which of the corresponding bits in
the identifier acceptance register are relevant for acceptance filtering. To
receive standard identifiers in 32 bit filter mode it is required to program
the last three bits (AM2–AM0) in the mask registers CIDMR1 and
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
351
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
CIDMR5 to ‘don’t care. To receive standard identifiers in 16 bit filter
mode it is required to program the last three bits (AM2–AM0) in the mask
registers CIDMR1, CIDMR3, CIDMR5 and CIDMR7 to ‘don’t care
Figure 17-16. Identifier Mask Registers (1st bank)
CIDMR0
$0114
CIDMR1
$0115
CIDMR2
$0116
CIDMR3
$0117
RESET
R
W
R
W
R
W
R
W
Bit 7
6
5
4
3
2
1
Bit 0
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
-
-
-
-
-
-
-
-
Figure 17-17. Identifier Mask Registers (2nd bank)
CIDMR4
$011C
CIDMR5
$011D
CIDMR6
$011E
CIDMR7
$011F
RESET
R
W
R
W
R
W
R
W
Bit 7
6
5
4
3
2
1
Bit 0
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
AM7
AM6
AM5
AM4
AM3
AM2
AM1
AM0
-
-
-
-
-
-
-
-
AM7 – AM0 — Acceptance Mask Bits
If a particular bit in this register is cleared this indicates that the
corresponding bit in the identifier acceptance register must be the
same as its identifier bit, before a match is detected. The message is
accepted if all such bits match. If a bit is set, it indicates that the state
of the corresponding bit in the identifier acceptance register does not
affect whether or not the message is accepted.
0 = Match corresponding acceptance code register and identifier bits.
1 = Ignore corresponding acceptance code register bit.
NOTE:
The CIDMR0–7 registers can only be written if the SFTRES bit in
CMCR0 is set.
Technical Data
352
MC68HC912DG128 — Rev 3.0
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
MSCAN Controller
17.13.15 msCAN12 Port CAN Control Register (PCTLCAN)
PCTLCAN R
$013D
W
RESET
Bit 7
0
6
0
5
0
4
0
3
0
2
0
0
0
0
0
0
0
1
Bit 0
PUPCAN
RDPCAN
0
0
The following bits control pins 7 through 2 of Port CAN when they are
implemented externally.
PUPCAN — Pull-Up Enable Port CAN
0 = Pull mode disabled for Port CAN.
1 = Pull mode enabled for Port CAN.
RDPCAN — Reduced Drive Port CAN
0 = Reduced drive disabled for Port CAN.
1 = Reduced drive enabled for Port CAN.
17.13.16 msCAN12 Port CAN Data Register (PORTCAN)
PORTCAN
$013E
RESET
R
W
Bit 7
6
5
4
3
2
PCAN7
PCAN6
PCAN5
PCAN4
PCAN3
PCAN2
-
-
-
1
TxCAN
Bit 0
RxCAN
-
-
Port bits 7 to 2 will read zero when configured as inputs because they
are not implemented externally.
When configured as output, port bits 7 to 2 will read the last value
written.
Reading bits 1 and 0 returns the value of the TxCan and RxCan pins,
respectively.
17.13.17 msCAN12 Port CAN Data Direction Register (DDRCAN)
DDRCAN R
$013F
W
RESET
Bit 7
6
5
4
3
2
DDCAN7
DDCAN6
DDCAN5
DDCAN4
DDCAN3
DDCAN2
0
0
0
0
0
0
1
0
Bit 0
0
0
0
DDCAN7 – DDCAN2 — This bits served as memory locations since
there are no corresponding external port pins.
Technical Data
353
MC68HC912DG128 — Rev 3.0
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
MSCAN Controller
Technical Data
354
MC68HC912DG128 — Rev 3.0
MSCAN Controller
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Section 18. Development Support
18.1 Contents
18.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355
18.3
Instruction Queue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 355
18.4
Background Debug Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . 357
18.5
Breakpoints. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 375
18.6
Instruction Tagging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 382
18.2 Introduction
Development support involves complex interactions between
MC68HC912DG128 resources and external development systems. The
following section concerns instruction queue and queue tracking signals,
background debug mode, and instruction tagging.
18.3 Instruction Queue
The CPU12 instruction queue provides at least three bytes of program
information to the CPU when instruction execution begins. The CPU12
always completely finishes executing an instruction before beginning to
execute the next instruction. Status signals IPIPE[1:0] provide
information about data movement in the queue and indicate when the
CPU begins to execute instructions. This makes it possible to monitor
CPU activity on a cycle-by-cycle basis for debugging. Information
available on the IPIPE[1:0] pins is time multiplexed. External circuitry
can latch data movement information on rising edges of the E-clock
signal; execution start information can be latched on falling edges. Table
18-1 shows the meaning of data on the pins.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Development Support
For More Information On This Product,
Go to: www.freescale.com
355
Freescale Semiconductor, Inc.
Development Support
Table 18-1. IPIPE Decoding
Data Movement — IPIPE[1:0] Captured at Rising Edge of E Clock(1)
IPIPE[1:0]
Mnemonic
Meaning
0:0
—
No Movement
0:1
LAT
Latch Data From Bus
1:0
ALD
Advance Queue and Load From Bus
1:1
ALL
Advance Queue and Load From Latch
Freescale Semiconductor, Inc...
Execution Start — IPIPE[1:0] Captured at Falling Edge of E Clock(2)
IPIPE[1:0]
Mnemonic
Meaning
0:0
—
No Start
0:1
INT
Start Interrupt Sequence
1:0
SEV
Start Even Instruction
1:1
SOD
Start Odd Instruction
1. Refers to data that was on the bus at the previous E falling edge.
2. Refers to bus cycle starting at this E falling edge.
Program information is fetched a few cycles before it is used by the CPU.
In order to monitor cycle-by-cycle CPU activity, it is necessary to
externally reconstruct what is happening in the instruction queue.
Internally the MCU only needs to buffer the data from program fetches.
For system debug it is necessary to keep the data and its associated
address in the reconstructed instruction queue. The raw signals required
for reconstruction of the queue are ADDR, DATA, R/W, ECLK, and
status signals IPIPE[1:0].
The instruction queue consists of two 16-bit queue stages and a holding
latch on the input of the first stage. To advance the queue means to
move the word in the first stage to the second stage and move the word
from either the holding latch or the data bus input buffer into the first
stage. To start even (or odd) instruction means to execute the opcode in
the high-order (or low-order) byte of the second stage of the instruction
queue.
Technical Data
356
MC68HC912DG128 — Rev 3.0
Development Support
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Development Support
Background Debug Mode
18.4 Background Debug Mode
Background debug mode (BDM) is used for system development, incircuit testing, field testing, and programming. BDM is implemented in
on-chip hardware and provides a full set of debug options.
Because BDM control logic does not reside in the CPU, BDM hardware
commands can be executed while the CPU is operating normally. The
control logic generally uses free CPU cycles to execute these
commands, but can steal cycles from the CPU when necessary. Other
BDM commands are firmware based, and require the CPU to be in active
background mode for execution. While BDM is active, the CPU executes
a firmware program located in a small on-chip ROM that is available in
the standard 64-Kbyte memory map only while BDM is active.
The BDM control logic communicates with an external host development
system serially, via the BKGD pin. This single-wire approach minimizes
the number of pins needed for development support.
18.4.1 Enabling BDM Firmware Commands
BDM is available in all operating modes, but must be made active before
firmware commands can be executed. BDM is enabled by setting the
ENBDM bit in the BDM STATUS register via the single wire interface
(using a hardware command; WRITE_BD_BYTE at $FF01). BDM must
then be activated to map BDM registers and ROM to addresses $FF00
to $FFFF and to put the MCU in active background mode.
After the firmware is enabled, BDM can be activated by the hardware
BACKGROUND command, by the BDM tagging mechanism, or by the
CPU BGND instruction. An attempt to activate BDM before firmware has
been enabled causes the MCU to resume normal instruction execution
after a brief delay.
BDM becomes active at the next instruction boundary following
execution of the BDM BACKGROUND command, but tags activate BDM
before a tagged instruction is executed.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Development Support
For More Information On This Product,
Go to: www.freescale.com
357
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Development Support
In special single-chip mode, background operation is enabled and active
immediately out of reset. This active case replaces the M68HC11 boot
function, and allows programming a system with blank memory.
While BDM is active, a set of BDM control registers are mapped to
addresses $FF00 to $FF06. The BDM control logic uses these registers
which can be read anytime by BDM logic, not user programs. Refer to
BDM Registers for detailed descriptions.
Some on-chip peripherals have a BDM control bit which allows
suspending the peripheral function during BDM. For example, if the timer
control is enabled, the timer counter is stopped while in BDM. Once
normal program flow is continued, the timer counter is re-enabled to
simulate real-time operations.
18.4.2 BDM Serial Interface
The BDM serial interface requires the external controller to generate a
falling edge on the BKGD pin to indicate the start of each bit time. The
external controller provides this falling edge whether data is transmitted
or received.
BKGD is a pseudo-open-drain pin that can be driven either by an
external controller or by the MCU. Data is transferred MSB first at 16 Bclock cycles per bit (nominal speed). The interface times out if 512 Bclock cycles occur between falling edges from the host. The hardware
clears the command register when a time-out occurs.
The BKGD pin can receive a high or low level or transmit a high or low
level. The following diagrams show timing for each of these cases.
Interface timing is synchronous to MCU clocks but asynchronous to the
external host. The internal clock signal is shown for reference in counting
cycles.
Figure 18-1 shows an external host transmitting a logic one or zero to the
BKGD pin of a target MC68HC912DG128 MCU. The host is
asynchronous to the target so there is a 0-to-1 cycle delay from the hostgenerated falling edge to where the target perceives the beginning of the
bit time. Ten target B cycles later, the target senses the bit level on the
BKGD pin. Typically the host actively drives the pseudo-open-drain
Technical Data
358
MC68HC912DG128 — Rev 3.0
Development Support
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Development Support
Background Debug Mode
BKGD pin during host-to-target transmissions to speed up rising edges.
Since the target does not drive the BKGD pin during this period, there is
no need to treat the line as an open-drain signal during host-to-target
transmissions.
B CLOCK
(TARGET MCU)
HOST
TRANSMIT 1
HOST
TRANSMIT 0
PERCEIVED
START
OF BIT TIME
TARGET SENSES BIT
EARLIEST
START OF
NEXT BIT
10 CYCLES
SYNCHRONIZATION
UNCERTAINTY
Figure 18-1. BDM Host to Target Serial Bit Timing
B CLOCK
(TARGET
MCU)
HOST
DRIVE TO
BKGD PIN
HIGH-IMPEDANCE
TARGET MCU
SPEEDUP PULSE
HIGH-IMPEDANCE
PERCEIVED
START OF BIT
TIME
HIGH-IMPEDANCE
R-C RISE
BKGD PIN
10 CYCLES
10 CYCLES
HOST SAMPLES
BKGD PIN
EARLIEST
START OF
NEXT BIT
Figure 18-2. BDM Target to Host Serial Bit Timing (Logic 1)
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Development Support
For More Information On This Product,
Go to: www.freescale.com
359
Freescale Semiconductor, Inc.
Development Support
Freescale Semiconductor, Inc...
Figure 18-2 shows the host receiving a logic one from the target
MC68HC912DG128 MCU. Since the host is asynchronous to the target
MCU, there is a 0-to-1 cycle delay from the host-generated falling edge
on BKGD to the perceived start of the bit time in the target MCU. The
host holds the BKGD pin low long enough for the target to recognize it
(at least two target B cycles). The host must release the low drive before
the target MCU drives a brief active-high speed-up pulse seven cycles
after the perceived start of the bit time. The host should sample the bit
level about ten cycles after it started the bit time.
B CLOCK
(TARGET
MCU)
HOST
DRIVE TO
BKGD PIN
HIGH-IMPEDANCE
SPEEDUP PULSE
TARGET MCU
DRIVE AND
SPEEDUP PULSE
PERCEIVED
START OF BIT TIME
BKGD PIN
10 CYCLES
10 CYCLES
EARLIEST
START OF
NEXT BIT
HOST SAMPLES
BKGD PIN
Figure 18-3. BDM Target to Host Serial Bit Timing (Logic 0)
Figure 18-3 shows the host receiving a logic zero from the target
MC68HC912DG128 MCU. Since the host is asynchronous to the target
MCU, there is a 0-to-1 cycle delay from the host-generated falling edge
on BKGD to the start of the bit time as perceived by the target MCU. The
host initiates the bit time but the target MC68HC912DG128 finishes it.
Since the target wants the host to receive a logic zero, it drives the
BKGD pin low for 13 B-clock cycles, then briefly drives it high to speed
up the rising edge. The host samples the bit level about ten cycles after
starting the bit time.
Technical Data
360
MC68HC912DG128 — Rev 3.0
Development Support
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Development Support
Background Debug Mode
18.4.3 BDM Commands
Freescale Semiconductor, Inc...
The BDM command set consists of two types: hardware and firmware.
Hardware commands allow target system memory to be read or written.
Target system memory includes all memory that is accessible by the
CPU12 including EEPROM, on-chip I/O and control registers, and
external memory that is connected to the target HC12 MCU. Hardware
commands are implemented in hardware logic and do not require the
HC12 MCU to be in BDM mode for execution. The control logic watches
the CPU12 buses to find a free bus cycle to execute the command so the
background access does not disturb the running application programs.
If a free cycle is not found within 128 B-clock cycles, the CPU12 is
momentarily frozen so the control logic can steal a cycle. Commands
implemented in BDM control logic are listed in Table 18-2.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Development Support
For More Information On This Product,
Go to: www.freescale.com
361
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Development Support
Table 18-2. Hardware Commands(1)
Command
BACKGROUND
Opcode (Hex)
90
Data
None
READ_BD_BYTE(1)
E4
16-bit address
16-bit data out
READ_BD_WORD(1)
EC
16-bit address
16-bit data out
READ_BYTE
E0
16-bit address
16-bit data out
READ_WORD
E8
16-bit address
16-bit data out
WRITE_BD_BYTE(1)
C4
16-bit address
16-bit data in
WRITE_BD_WORD(1)
CC
16-bit address
16-bit data in
WRITE_BYTE
C0
16-bit address
16-bit data in
WRITE_WORD
C8
16-bit address
16-bit data in
Description
Enter background mode if firmware enabled.
Read from memory with BDM in map (may steal
cycles if external access) data for odd address on
low byte, data for even address on high byte.
Read from memory with BDM in map (may steal
cycles if external access). Must be aligned access.
Read from memory with BDM out of map (may steal
cycles if external access) data for odd address on
low byte, data for even address on high byte.
Read from memory with BDM out of map (may steal
cycles if external access). Must be aligned access.
Write to memory with BDM in map (may steal cycles
if external access) data for odd address on low byte,
data for even address on high byte.
Write to memory with BDM in map (may steal cycles
if external access). Must be aligned access.
Write to memory with BDM out of map (may steal
cycles if external access) data for odd address on
low byte, data for even address on high byte.
Write to memory with BDM out of map (may steal
cycles if external access). Must be aligned access.
1. Use these commands only for reading/writing to BDM locations.The BDM firmware ROM and BDM registers are not normally
in the HC12 MCU memory map.Since these locations have the same addresses as some of the normal application memory
map, there needs to be a way to decide which physical locations are being accessed by the hardware BDM commands.This
gives rise to needing separate memory access commands for the BDM locations as opposed to the normal application locations.In logic, this is accomplished by momentarily enabling the BDM memory resources, just for the access cycles of the
READ_BD and WRITE_BD commands.This logic allows the debugging system to unobtrusively access the BDM locations
even if the application program is running out of the same memory area in the normal application memory map.
The second type of BDM commands are firmware commands
implemented in a small ROM within the HC12 MCU. The CPU must be
in background mode to execute firmware commands. The usual way to
get to background mode is by the hardware command BACKGROUND.
The BDM ROM is located at $FF20 to $FFFF while BDM is active. There
are also seven bytes of BDM registers located at $FF00 to $FF06 when
BDM is active. The CPU executes code in the BDM firmware to perform
the requested operation. The BDM firmware watches for serial
commands and executes them as they are received. The firmware
commands are shown in Table 18-3.
Technical Data
362
MC68HC912DG128 — Rev 3.0
Development Support
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Development Support
Background Debug Mode
Table 18-3. BDM Firmware Commands
READ_NEXT
READ_PC
READ_D
READ_X
READ_Y
READ_SP
WRITE_NEXT
WRITE_PC
WRITE_D
WRITE_X
WRITE_Y
WRITE_SP
GO
Opcode
(Hex)
62
63
64
65
66
67
42
43
44
45
46
47
08
16-bit data out
16-bit data out
16-bit data out
16-bit data out
16-bit data out
16-bit data out
16-bit data in
16-bit data in
16-bit data in
16-bit data in
16-bit data in
16-bit data in
None
TRACE1
10
None
TAGGO
18
None
Command
Data
Description
X = X + 2; Read next word pointed to by X
Read program counter
Read D accumulator
Read X index register
Read Y index register
Read stack pointer
X = X + 2; Write next word pointed to by X
Write program counter
Write D accumulator
Write X index register
Write Y index register
Write stack pointer
Go to user program
Execute one user instruction then return to
BDM
Enable tagging and go to user program
Each of the hardware and firmware BDM commands start with an 8-bit
command code (opcode). Depending upon the commands, a 16-bit
address and/or a 16-bit data word is required as indicated in the tables
by the command. All the read commands output 16-bits of data despite
the byte/word implication in the command name.
The external host should wait 150 BCLK cycles for a non-intrusive BDM
command to execute before another command is sent. This delay
includes 128 BCLK cycles for the maximum delay for a free cycle. For
data read commands, the host must insert this delay between sending
the address and attempting to read the data. In the case of a write
command, the host must delay after the data portion before sending a
new command to be sure that the write has finished.
The external host should delay about 32 target BCLK cycles between a
firmware read command and the data portion of these commands. This
allows the BDM firmware to execute the instructions needed to get the
requested data into the BDM SHIFTER register.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Development Support
For More Information On This Product,
Go to: www.freescale.com
363
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Development Support
The external host should delay about 32 target BCLK cycles after the
data portion of firmware write commands to allow BDM firmware to
complete the requested write operation before a new serial command
disturbs the BDM SHIFTER register.
The external host should delay about 64 target BCLK cycles after a
TRACE1 or GO command before starting any new serial command. This
delay is needed because the BDM SHIFTER register is used as a
temporary data holding register during the exit sequence to user code.
BDM logic retains control of the internal buses until a read or write is
completed. If an operation can be completed in a single cycle, it does not
intrude on normal CPU12 operation. However, if an operation requires
multiple cycles, CPU12 clocks are frozen until the operation is complete.
18.4.4 BDM Lockout
The access to the MCU resources by BDM may be prevented by
enabling the BDM lockout feature. When enabled, the BDM lockout
mechanism prevents the BDM from being active. In this case the BDM
ROM is disabled and does not appear in the MCU memory map.
BDM lockout is enabled by clearing NOBDML bit of EEMCR register.
The NOBDML bit is loaded at reset from the SHADOW byte of EEPROM
module. Modifying the state of the NOBDML and corresponding
EEPROM SHADOW bit is only possible in special modes.
Please refer to EEPROM Memory for NOBDML information.
Technical Data
364
MC68HC912DG128 — Rev 3.0
Development Support
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Development Support
Background Debug Mode
18.4.4.1 Enabling BDM lockout
Enabling the BDM lockout feature is only possible in special modes
(SMODN=0) and is accomplished by the following steps.
1. Remove the SHADOW byte protection by clearing SHPROT bit in
EEPROT register.
2. Clear NOSHB bit in EEMCR register to make the SHADOW byte
visible at $0FC0.
3. Program bit 7 of the SHADOW byte like a regular EEPROM
location at address $0FC0 (write $7F into address $0FC0). Do not
program other bits of the SHADOW byte (location $0FC0);
otherwise some regular EEPROM array locations will not be
visible. At the next reset, the SHADOW byte is loaded into the
EEMCR register. NOBDML bit in EEMCR will be cleared and BDM
will not be operational.
4. Protect the SHADOW byte by setting SHPROT bit in EEPROT
register.
18.4.4.2 Disabling BDM lockout
Disabling the BDM lockout is only possible in special modes
(SMODN=0). Follow the same steps as for enabling the BDM lockout,
but erase the SHADOW byte.
At the next reset, the SHADOW byte is loaded into the EEMCR register.
NOBDML bit in EEMCR will be set and BDM becomes operational.
NOTE:
When the BDM lockout is enabled it is not possible to run code from the
reset vector in special single chip mode.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Development Support
For More Information On This Product,
Go to: www.freescale.com
365
Freescale Semiconductor, Inc.
Development Support
18.4.5 BDM Registers
Seven BDM registers are mapped into the standard 64-Kbyte address
space when BDM is active. Mapping is shown in Table 18-4.
Freescale Semiconductor, Inc...
Table 18-4. BDM registers
Address
Register
$FF00
BDM Instruction Register
$FF01
BDM Status Register
$FF02 – $FF03
BDM Shift Register
$FF04 – $FF05
BDM Address Register
$FF06
BDM CCR Holding Register
•
The INSTRUCTION register content is determined by the type of
background command being executed.
•
The STATUS register indicates BDM operating conditions.
•
The SHIFT register contains data being received or transmitted
via the serial interface.
•
The ADDRESS register is temporary storage for BDM commands.
•
The CCRSAV register preserves the content of the CPU12 CCR
while BDM is active.
The only registers of interest to users are the STATUS register and the
CCRSAV register. The other BDM registers are only used by the BDM
firmware to execute commands. The registers are accessed by means
of the hardware READ_BD and WRITE_BD commands, but should not
be written during BDM operation (except the CCRSAV register which
could be written to modify the CCR value).
Technical Data
366
MC68HC912DG128 — Rev 3.0
Development Support
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Development Support
Background Debug Mode
18.4.5.1 STATUS
The STATUS register is read and written by the BDM hardware as a
result of serial data shifted in on the BKGD pin.
Read: all modes.
Write: Bits 3 through 5, and bit 7 are writable in all modes. Bit 6,
BDMACT, can only be written if bit 7 H/F in the INSTRUCTION register
is a zero. Bit 2, CLKSW, can only be written if bit 7 H/F in the
INSTRUCTION register is a one. A user would never write ones to bits
3 through 5 because these bits are only used by BDM firmware.
BIT 7
6
5
4
3
2
1
BIT 0
ENBDM
BDMACT
ENTAG
SDV
TRACE
CLKSW
-
-
RESET:
0
(NOTE 1)
1
0
0
0
0
0
0
Special
Single Chip
& Periph
RESET:
0
0
0
0
0
0
0
0
All other
modes
STATUS— BDM Status Register(1)
$FF01
1. ENBDM is set to 1 by the firmware in Special Single Chip mode.
ENBDM — Enable BDM (permit active background debug mode)
0 = BDM cannot be made active (hardware commands still
allowed).
1 = BDM can be made active to allow firmware commands.
BDMACT — Background Mode Active Status
BDMACT becomes set as active BDM mode is entered so that the
BDM firmware ROM is enabled and put into the map. BDMACT is
cleared by a carefully timed store instruction in the BDM firmware as
part of the exit sequence to return to user code and remove the BDM
memory from the map. This bit has 4 clock cycles write delay.
0 = BDM is not active. BDM ROM and registers are not in map.
1 = BDM is active and waiting for serial commands. BDM ROM and
registers are in map
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Development Support
For More Information On This Product,
Go to: www.freescale.com
367
Freescale Semiconductor, Inc.
Development Support
Freescale Semiconductor, Inc...
The user should be careful that the state of the BDMACT bit is not
unintentionally changed with the WRITE_NEXT firmware command.
If it is unintentionally changed from 1 to 0, it will cause a system
runaway because it would disable the BDM firmware ROM while the
CPU12 was executing BDM firmware. The following two commands
show how BDMACT may unintentionally get changed from 1 to 0.
WRITE_X with data $FEFE
WRITE_NEXT with data $C400
The first command writes the data $FEFE to the X index register. The
second command writes the data $C4 to the $FF00 INSTRUCTION
register and also writes the data $00 to the $FF01 STATUS register.
ENTAG — Tagging Enable
Set by the TAGGO command and cleared when BDM mode is
entered. The serial system is disabled and the tag function enabled
16 cycles after this bit is written.
0 = Tagging not enabled, or BDM active.
1 = Tagging active. BDM cannot process serial commands while
tagging is active.
SDV — Shifter Data Valid
Shows that valid data is in the serial interface shift register. Used by
the BDM firmware.
0 = No valid data. Shift operation is not complete.
1 = Valid Data. Shift operation is complete.
TRACE — Asserted by the TRACE1 command
CLKSW — Clock Switch
0 = BDM system operates with BCLK.
1 = BDM system operates with ECLK.
The WRITE_BD_BYTE@FF01 command that changes CLKSW
including 150 cycles after the data portion of the command should be
timed at the old speed. Beginning with the start of the next BDM
command, the new clock can be used for timing BDM communications.
If ECLK rate is slower than BCLK rate, CLKSW is ignored and BDM
system is forced to operate with ECLK.
Technical Data
368
MC68HC912DG128 — Rev 3.0
Development Support
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Development Support
Background Debug Mode
18.4.5.2 INSTRUCTION - Hardware Instruction Decode
The INSTRUCTION register is written by the BDM hardware as a result
of serial data shifted in on the BKGD pin. It is readable and writable in
Special Peripheral mode on the parallel bus. It is discussed here for two
conditions: when a hardware command is executed and when a
firmware command is executed.
Read and write: all modes
The hardware clears the INSTRUCTION register if 512 BCLK cycles
occur between falling edges from the host.
RESET:
BIT 7
6
5
4
3
2
1
BIT 0
H/F
DATA
R/W
BKGND
W/B
BD/U
0
0
0
0
0
0
0
0
0
0
INSTRUCTION — BDM Instruction Register (hardware command explanation)
$FF00
The bits in the BDM instruction register have the following meanings
when a hardware command is executed.
H/F — Hardware/Firmware Flag
0 = Firmware command
1 = Hardware command
DATA — Data Flag - Shows that data accompanies the command.
0 = No data
1 = Data follows the command
R/W — Read/Write Flag
0 = Write
1 = Read
BKGND — Hardware request to enter active background mode
0 = Not a hardware background command
1 = Hardware background command (INSTRUCTION = $90)
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Development Support
For More Information On This Product,
Go to: www.freescale.com
369
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Development Support
W/B — Word/Byte Transfer Flag
0 = Byte transfer
1 = Word transfer
BD/U — BDM Map/User Map Flag
Indicates whether BDM registers and ROM are mapped to addresses
$FF00 to $FFFF in the standard 64-Kbyte address space. Used only
by hardware read/write commands.
0 = BDM resources not in map
1 = BDM ROM and registers in map
Bit 7
6
5
H/F
DATA
R/W
4
3
2
TTAGO
INSTRUCTION — BDM Instruction Register (firmware command bit explanation)
1
Bit 0
REGN
$FF00
The bits in the BDM instruction register have the following meanings
when a firmware command is executed.
H/F — Hardware/Firmware Flag
0 = Firmware command
1 = Hardware command
DATA — Data Flag - Shows that data accompanies the command.
0 = No data
1 = Data follows the command
R/W — Read/Write Flag
0 = Write
1 = Read
Technical Data
370
MC68HC912DG128 — Rev 3.0
Development Support
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Development Support
Background Debug Mode
TTAGO — Trace, Tag, Go Field
Table 18-5. TTAGO Decoding
Table 18-6TTAGO Value
Table 18-7Instruction
00
—
01
GO
10
TRACE1
11
TAGGO
Freescale Semiconductor, Inc...
REGN — Register/Next Field
Indicates which register is being affected by a command. In the case
of a READ_NEXT or WRITE_NEXT command, index register X is
pre-incriminated by 2 and the word pointed to by X is then read or
written.
Table 18-8. REGN Decoding
REGN Value
Instruction
000
—
001
—
010
READ/WRITE NEXT
011
PC
100
D
101
X
110
Y
111
SP
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Development Support
For More Information On This Product,
Go to: www.freescale.com
371
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Development Support
18.4.5.3 SHIFTER
This 16-bit shift register contains data being received or transmitted via
the serial interface. It is also used by the BDM firmware for temporary
storage.
Read: all modes (but not normally accessed by users)
Write: all modes (but not normally accessed by users)
BIT 15
14
13
12
11
10
9
BIT 8
S15
S14
S13
S12
S11
S10
S9
S8
X
X
X
X
X
X
X
X
RESET:
SHIFTER— BDM Shift Register - High Byte
$FF02
BIT 7
6
5
4
3
2
1
BIT 0
S7
S6
S5
S4
S3
S2
S1
S0
X
X
X
X
X
X
X
X
RESET:
SHIFTER— BDM Shift Register - Low Byte
Technical Data
372
$FF03
MC68HC912DG128 — Rev 3.0
Development Support
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Development Support
Background Debug Mode
18.4.5.4 ADDRESS
This 16-bit address register is temporary storage for BDM hardware and
firmware commands.
Read: all modes (but not normally accessed by users)
Write: only by BDM hardware (state machine)
RESET:
BIT 15
14
13
12
11
10
9
BIT 8
A15
A14
A13
A12
A11
A10
A9
A8
X
X
X
X
X
X
X
X
ADDRESS— BDM Address Register - High Byte
RESET:
$FF04
BIT 7
6
5
4
3
2
1
BIT 0
A7
A6
A5
A4
A3
A2
A1
A0
X
X
X
X
X
X
X
X
ADDRESS— BDM Address Register - Low Byte
MC68HC912DG128 — Rev 3.0
MOTOROLA
$FF05
Technical Data
Development Support
For More Information On This Product,
Go to: www.freescale.com
373
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Development Support
18.4.5.5 CCRSAV
The CCRSAV register is used to save the CCR of the users program
when entering BDM. It is also used for temporary storage in the BDM
firmware.
Read and write: all modes
BIT 7
6
5
4
3
2
1
BIT 0
CCR7
CCR6
CCR5
CCR4
CCR3
CCR2
CCR1
CCR0
X
X
X
X
X
X
X
X
RESET:
NOTE 1 (1)
CCRSAV— BDM CCR Holding Register
$FF06
1. Initialized to equal the CPU12 CCR register by the firmware.
Technical Data
374
MC68HC912DG128 — Rev 3.0
Development Support
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Development Support
Breakpoints
18.5 Breakpoints
Hardware breakpoints are used to debug software on the
MC68HC912DG128 by comparing actual address and data values to
predetermined data in setup registers. A successful comparison will
place the CPU in background debug mode (BDM) or initiate a software
interrupt (SWI). Breakpoint features designed into the
MC68HC912DG128 include:
•
Mode selection for BDM or SWI generation
•
Program fetch tagging for cycle of execution breakpoint
•
Second address compare in dual address modes
•
Range compare by disable of low byte address
•
Data compare in full feature mode for non-tagged breakpoint
•
Byte masking for high/low byte data compares
•
R/W compare for non-tagged compares
•
Tag inhibit on BDM TRACE
18.5.1 Breakpoint Modes
Three modes of operation determine the type of breakpoint in effect.
•
Dual address-only breakpoints, each of which will cause a
software interrupt (SWI)
•
Single full-feature breakpoint which will cause the part to enter
background debug mode (BDM)
•
Dual address-only breakpoints, each of which will cause the part
to enter BDM
Breakpoints will not occur when BDM is active.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Development Support
For More Information On This Product,
Go to: www.freescale.com
375
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Development Support
18.5.1.1 SWI Dual Address Mode
In this mode, dual address-only breakpoints can be set, each of which
cause a software interrupt. This is the only breakpoint mode which can
force the CPU to execute a SWI. Program fetch tagging is the default in
this mode; data breakpoints are not possible. In the dual mode each
address breakpoint is affected by the BKPM bit and the BKALE bit. The
BKxRW and BKxRWE bits are ignored. In dual address mode the
BKDBE becomes an enable for the second address breakpoint. The
BKSZ8 bit will have no effect when in a dual address mode.
18.5.1.2 BDM Full Breakpoint Mode
A single full feature breakpoint which causes the part to enter
background debug mode. BDM mode may be entered by a breakpoint
only if an internal signal from the BDM indicates background debug
mode is enabled.
•
Breakpoints are not allowed if the BDM mode is already active.
Active mode means the CPU is executing out of the BDM ROM.
•
BDM should not be entered from a breakpoint unless the ENABLE
bit is set in the BDM. This is important because even if the
ENABLE bit in the BDM is negated the CPU actually does execute
the BDM ROM code. It checks the ENABLE and returns if not set.
If the BDM is not serviced by the monitor then the breakpoint
would be re-asserted when the BDM returns to normal CPU flow.
•
There is no hardware to enforce restriction of breakpoint operation
if the BDM is not enabled.
18.5.1.3 BDM Dual Address Mode
Dual address-only breakpoints, each of which cause the part to enter
background debug mode. In the dual mode each address breakpoint is
affected, consistent across modes, by the BKPM bit, the BKALE bit, and
the BKxRW and BKxRWE bits. In dual address mode the BKDBE
becomes an enable for the second address breakpoint. The BKSZ8 bit
will have no effect when in a dual address mode. BDM mode may be
Technical Data
376
MC68HC912DG128 — Rev 3.0
Development Support
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Development Support
Breakpoints
entered by a breakpoint only if an internal signal from the BDM indicates
background debug mode is enabled.
•
BKDBE will be used as an enable for the second address only
breakpoint.
•
Breakpoints are not allowed if the BDM mode is already active.
Active mode means the CPU is executing out of the BDM ROM.
•
BDM should not be entered from a breakpoint unless the ENABLE
bit is set in the BDM. This is important because even if the
ENABLE bit in the BDM is negated the CPU actually does execute
the BDM ROM code. It checks the ENABLE and returns if not set.
If the BDM is not serviced by the monitor then the breakpoint
would be re-asserted when the BDM returns to normal CPU flow.
There is no hardware to enforce restriction of breakpoint operation
if the BDM is not enabled.
18.5.2 Breakpoint Registers
Breakpoint operation consists of comparing data in the breakpoint
address registers (BRKAH/BRKAL) to the address bus and comparing
data in the breakpoint data registers (BRKDH/BRKDL) to the data bus.
The breakpoint data registers can also be compared to the address bus.
The scope of comparison can be expanded by ignoring the least
significant byte of address or data matches.
The scope of comparison can be limited to program data only by setting
the BKPM bit in breakpoint control register 0.
To trace program flow, setting the BKPM bit causes address comparison
of program data only. Control bits are also available that allow checking
read/write matches.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Development Support
For More Information On This Product,
Go to: www.freescale.com
377
Freescale Semiconductor, Inc.
Development Support
Bit 7
6
5
4
3
2
1
Bit 0
BKEN1
BKEN0
BKPM
0
BK1ALE
BK0ALE
0
0
0
0
0
0
0
0
0
0
RESET:
BRKCT0 — Breakpoint Control Register 0
$0020
Freescale Semiconductor, Inc...
Read and write anytime.
This register is used to control the breakpoint logic.
BKEN1, BKEN0 — Breakpoint Mode Enable
Table 18-9. Breakpoint Mode Control
BKEN1 BKEN0
Mode Selected
0
0
Breakpoints Off
0
1
SWI — Dual Address Mode
1
0
BDM — Full Breakpoint Mode
1
1
BDM — Dual Address Mode
BRKAH/L Usage BRKDH/L Usage
—
—
Address Match
Address Match
Address Match
Data Match
Address Match
Address Match
R/W
—
No
Yes
Yes
Range
—
Yes
Yes
Yes
BKPM — Break on Program Addresses
This bit controls whether the breakpoint will cause a break on a match
(next instruction boundary) or on a match that will be an executable
opcode. Data and non-executed opcodes cannot cause a break if this
bit is set. This bit has no meaning in SWI dual address mode. The
SWI mode only performs program breakpoints.
0 = On match, break at the next instruction boundary
1 = On match, break if the match is an instruction that will be
executed. This uses tagging as its breakpoint mechanism.
BK1ALE — Breakpoint 1 Range Control
Only valid in dual address mode.
0 = BRKDL will not be used to compare to the address bus.
1 = BRKDL will be used to compare to the address bus.
BK0ALE — Breakpoint 0 Range Control
Valid in all modes.
0 = BRKAL will not be used to compare to the address bus.
1 = BRKAL will be used to compare to the address bus.
Technical Data
378
MC68HC912DG128 — Rev 3.0
Development Support
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Development Support
Breakpoints
Table 18-10. Breakpoint Address Range Control
BK1ALE BK0ALE
Address Range Selected
–
0
Upper 8-bit address only for full mode or dual mode BKP0
–
1
Full 16-bit address for full mode or dual mode BKP0
0
–
Upper 8-bit address only for dual mode BKP1
1
–
Full 16-bit address for dual mode BKP1
RESET:
Bit 7
6
5
4
3
2
1
Bit 0
0
BKDBE
BKMBH
BKMBL
BK1RWE
BK1RW
BK0RWE
BK0RW
0
0
0
0
0
0
0
0
BRKCT1 — Breakpoint Control Register 1
$0021
This register is read/write in all modes.
BKDBE — Enable Data Bus
Enables comparing of address or data bus values using the BRKDH/L
registers.
0 = The BRKDH/L registers are not used in any comparison
1 = The BRKDH/L registers are used to compare address or data
(depending upon the mode selections BKEN1,0)
BKMBH — Breakpoint Mask High
Disables the comparing of the high byte of data when in full breakpoint
mode. Used in conjunction with the BKDBE bit (which should be set)
0 = High byte of data bus (bits 15:8) are compared to BRKDH
1 = High byte is not used in comparisons
BKMBL — Breakpoint Mask Low
Disables the matching of the low byte of data when in full breakpoint
mode. Used in conjunction with the BKDBE bit (which should be set)
0 = Low byte of data bus (bits 7:0) are compared to BRKDL
1 = Low byte is not used in comparisons.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Development Support
For More Information On This Product,
Go to: www.freescale.com
379
Freescale Semiconductor, Inc.
Development Support
BK1RWE — R/W Compare Enable
Enables the comparison of the R/W signal to further specify what
causes a match. This bit is NOT useful in program breakpoints or in
full breakpoint mode. This bit is used in conjunction with a second
address in dual address mode when BKDBE=1.
0 = R/W is not used in comparisons
1 = R/W is used in comparisons
BK1RW — R/W Compare Value
Freescale Semiconductor, Inc...
When BK1RWE = 1, this bit determines the type of bus cycle to
match.
0 = A write cycle will be matched
1 = A read cycle will be matched
BK0RWE — R/W Compare Enable
Enables the comparison of the R/W signal to further specify what
causes a match. This bit is not useful in program breakpoints.
0 = R/W is not used in the comparisons
1 = R/W is used in comparisons
BK0RW — R/W Compare Value
When BK0RWE = 1, this bit determines the type of bus cycle to match
on.
0 = Write cycle will be matched
1 = Read cycle will be matched
Table 18-11. Breakpoint Read/Write Control
BK1RWE BK1RW BK0RWE BK0RW
Read/Write Selected
–
–
0
X
R/W is don’t care for full mode or dual mode BKP0
–
–
1
0
R/W is write for full mode or dual mode BKP0
–
–
1
1
R/W is read for full mode or dual mode BKP0
0
X
–
–
R/W is don’t care for dual mode BKP1
1
0
–
–
R/W is write for dual mode BKP1
1
1
–
–
R/W is read for dual mode BKP1
Technical Data
380
MC68HC912DG128 — Rev 3.0
Development Support
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Development Support
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
0
0
0
0
0
0
0
0
RESET:
BRKAH — Breakpoint Address Register, High Byte
$0022
These bits are used to compare against the most significant byte of the
address bus.
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
RESET:
BRKAL — Breakpoint Address Register, Low Byte
$0023
These bits are used to compare against the least significant byte of the
address bus. These bits may be excluded from being used in the match
if BK0ALE = 0.
Bit 7
6
5
4
3
2
1
Bit 0
Bit 15
14
13
12
11
10
9
Bit 8
0
0
0
0
0
0
0
0
RESET:
BRKDH — Breakpoint Data Register, High Byte
$0024
These bits are compared to the most significant byte of the data bus or
the most significant byte of the address bus in dual address modes.
BKEN[1:0], BKDBE, and BKMBH control how this byte will be used in the
breakpoint comparison.
Technical Data
381
MC68HC912DG128 — Rev 3.0
Development Support
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Development Support
Bit 7
6
5
4
3
2
1
Bit 0
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
0
RESET:
BRKDL — Breakpoint Data Register, Low Byte
$0025
These bits are compared to the least significant byte of the data bus or
the least significant byte of the address bus in dual address modes.
BKEN[1:0], BKDBE, BK1ALE, and BKMBL control how this byte will be
used in the breakpoint comparison.
18.6 Instruction Tagging
The instruction queue and cycle-by-cycle CPU activity can be
reconstructed in real time or from trace history that was captured by a
logic analyzer. However, the reconstructed queue cannot be used to
stop the CPU at a specific instruction, because execution has already
begun by the time an operation is visible outside the MCU. A separate
instruction tagging mechanism is provided for this purpose.
Executing the BDM TAGGO command configures two MCU pins for
tagging. The TAGLO signal shares a pin with the LSTRB signal, and the
TAGHI signal shares a pin with the BKGD signal. Tagging information is
latched on the falling edge of ECLK.
Table 18-12 shows the functions of the two tagging pins. The pins
operate independently - the state of one pin does not affect the function
of the other. The presence of logic level zero on either pin at the fall of
ECLK performs the indicated function. Tagging is allowed in all modes.
Tagging is disabled when BDM becomes active and BDM serial
commands are not processed while tagging is active.
Technical Data
382
MC68HC912DG128 — Rev 3.0
Development Support
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Development Support
Instruction Tagging
Table 18-12. Tag Pin Function
TAGHI
TAGLO
Tag
1
1
no tag
1
0
low byte
0
1
high byte
0
0
both bytes
Freescale Semiconductor, Inc...
The tag follows program information as it advances through the queue.
When a tagged instruction reaches the head of the queue, the CPU
enters active background debugging mode rather than execute the
instruction.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Development Support
For More Information On This Product,
Go to: www.freescale.com
383
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Development Support
Technical Data
384
MC68HC912DG128 — Rev 3.0
Development Support
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Section 19. Electrical Specifications
19.1 Contents
19.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 385
19.3
Tables of Data . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 386
19.2 Introduction
The MC68HC912DG128 microcontroller unit (MCU) is a16-bit device
composed of standard on-chip peripherals including a 16-bit central
processing unit (CPU12), 128-Kbyte flash EEPROM, 8K byte RAM, 2K
byte EEPROM, two asynchronous serial communications interfaces
(SCI), a serial peripheral interface (SPI), an 8-channel, 16-bit timer,
two16-bit pulse accumulators and 16-bit down counter (ECT), two 10-bit
analog-to-digital converter (ADC), a four-channel pulse-width modulator
(PWM), an IIC interface module, and two MSCAN modules. The chip is
the first 16-bit microcontroller to include both byte-erasable EEPROM
and flash EEPROM on the same device. System resource mapping,
clock generation, interrupt control and bus interfacing are managed by
the Lite integration module (LIM). The MC68HC912DG128 has full 16bit data paths throughout, however, the multiplexed external bus can
operate in an 8-bit narrow mode so single 8-bit wide memory can be
interfaced for lower cost systems.
This section contains the most accurate electrical information for the
MC68HC912DG128 microcontroller available at the time of publication.
The following characteristics are contained in this document:
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
385
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Electrical Specifications
19.3 Tables of Data
Table 19-1. Maximum Ratings(1)
Rating
Symbol
Value
Unit
VDD, VDDA, VDDX
−0.3 to +6.5
V
VIN
−0.3 to +6.5
V
Operating temperature range
68HC912DG128PV8
68HC912DG128CPV8
68HC912DG128VPV8
68HC912DG128MPV8
TA
TL to TH
0 to +70
−40 to +85
−40 to +105
−40 to +125
°C
Storage temperature range
Tstg
−55 to +150
°C
Current drain per pin(2)
Excluding VDD and VSS
IIN
±25
mA
VDD−VDDX
6.5
V
Supply voltage
Input voltage
VDD differential voltage
1. Permanent damage can occur if maximum ratings are exceeded. Exposures to voltages or currents in excess of recommended values affects device reliability. Device modules may not operate normally while being exposed to electrical extremes.
2. One pin at a time, observing maximum power dissipation limits. Internal circuitry protects the inputs against damage
caused by high static voltages or electric fields; however, normal precautions are necessary to avoid application of any
voltage higher than maximum-rated voltages to this high-impedance circuit. Extended operation at the maximum ratings
can adversely affect device reliability. Tying unused inputs to an appropriate logic voltage level (either GND or VDD) enhances reliability of operation.
Table 19-2. Thermal Characteristics
Characteristic
Symbol
Value
Unit
Average junction temperature
TJ
TA + (PD × ΘJA)
°C
Ambient temperature
TA
User-determined
°C
ΘJA
40
°C/W
Package thermal resistance (junction-to-ambient)
112-pin quad flat pack (QFP)
PINT + PI/O or
dissipation(1)
PD
K
-------------------------T J + 273°C
W
Device internal power dissipation
PINT
IDD × VDD
W
I/O pin power dissipation(2)
PI/O
User-determined
W
K
PD × (TA + 273°C) + ΘJA × PD2
W · °C
Total power
A constant(3)
1. This is an approximate value, neglecting PI/O.
2. For most applications PI/O « PINT and can be neglected.
3. K is a constant pertaining to the device. Solve for K with a known TA and a measured PD (at equilibrium). Use this value of
K to solve for PD and TJ iteratively for any value of TA.
Technical Data
386
MC68HC912DG128 — Rev 3.0
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Electrical Specifications
Tables of Data
Table 19-3. DC Electrical Characteristics
VDD = 5.0 Vdc ±10%, VSS = 0 Vdc, TA = TL to TH, unless otherwise noted
Characteristic
Symbol
Min
Max
Unit
Input high voltage, all inputs
VIH
0.7 × VDD
VDD + 0.3
V
Input low voltage, all inputs
VIL
VSS−0.3
0.2 × VDD
V
VOH
VDD − 0.2
VDD − 0.8
—
—
V
V
VDD − 0.2
VDD − 0.8
—
—
V
V
—
—
VSS+0.2
VSS+0.4
V
V
—
—
VSS+0.2
VSS+0.4
V
V
Output high voltage, all I/O and output pins except XTAL
Normal drive strength
IOH = −10.0 µA
IOH = −0.8 mA
Reduced drive strength
IOH = −4.0 µA
IOH = −0.3 mA
Output low voltage, all I/O and output pins except XTAL
Normal drive strength
IOL = 10.0 µA
IOL = 1.6 mA
VOL
Reduced drive strength
IOL = 3.6 µA
IOL = 0.6 mA
Input leakage current(1)
Vin = VDD or VSSAll input only pins except ATD(2) and VFP
Iin
—
±5.0
µA
Three-state leakage, I/O ports, BKGD, and RESET
IOZ
—
±2.5
µA
Input capacitance
All input pins and ATD pins (non-sampling)
ATD pins (sampling)
All I/O pins
Cin
—
—
—
10
15
20
pF
pF
pF
Output load capacitance
All outputs except PS[7:4]
PS[7:4] when configured as SPI
CL
—
—
90
200
pF
pF
50
500
µA
50
50
500
500
µA
µA
1.5
—
V
Programmable active pull-up/pull-down current
IRQ, XIRQ, DBE, LSTRB, R/W. ports A, B, H, J, K, P, S, T, IB[7:4],
RXCAN1, .RXCAN0
MODA, MODB active pull down during reset
BKGD passive pull up
IAPU
RAM standby voltage, power down
Vsb
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
387
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Electrical Specifications
Table 19-3. DC Electrical Characteristics
VDD = 5.0 Vdc ±10%, VSS = 0 Vdc, TA = TL to TH, unless otherwise noted
Characteristic
Ram standby current
DC injection current(3) (4) (5) (6) (7)
(VNEGCLAMP=VSS–0.3V, VPOSTCLAMP=VDDE+0.3)
Steady state single pin limit
Steady state package limit includes sum of all stressed pins (25
pins max.)
Transient single pin limit
Transient package limit includes sum of all stressed pins (25 pins
max.)
Symbol
Min
Max
Unit
Isb
—
50
µA
IICsss
IICssP
–0.5
–10
0.5
10
IICTRs
IICTRP
–25
–25
25
25
mA
1. Specification is for parts in the -40 to +85°C range. Higher temperature ranges will result in increased
current leakage.
2. See Table 19-5.
3. It is recommended to tie VDD if standby mode is not being used.
4. All functional no-supply pins are internally clamped to VSS and VDD or VSS and VDDX.
5. Input must be current limited to the value specified. To determine the value of the required current-limiting resistor, calculate
resistance values for positive and negative clamp voltages, then use the larger of the two values.
6. Power supply must maintain regulation within operating VDD or VDDX range during instantaneous and operating maximum
current conditions. If positive injection current (Vin>VDD or Vin>VDDX) is greater than IDD or IDDX, injection current may flow
out of VDD/VDDX and could result in external power supply going out of regulation. Ensure external VDD/VDDX load will shunt
current greater than maximum injection current. This will be the greatest risk when the MCU is not consuming power. Examples are: if no system clock is present, or if clock rate is very low, which would reduce overall power consumption.
7. Current injection specification does not include ATD pins.
Technical Data
388
MC68HC912DG128 — Rev 3.0
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Electrical Specifications
Tables of Data
Table 19-4. Supply Current
VDD = 5.0 Vdc ±10%, VSS = 0 Vdc, TA = TL to TH, unless otherwise noted
Characteristic
Maximum total supply current
RUN:
Single-chip mode
Expanded mode
Symbol
IDD
WAIT: (All peripheral functions shut down)
Single-chip mode
Expanded mode
WIDD
STOP:
Single-chip mode, no clocks
SIDD
8 MHz
Unit
60
100
mA
mA
15
20
mA
mA
200
µA
Table 19-5. ATD DC Electrical Characteristics
VDD = 5.0 Vdc ±10%, VSS = 0 Vdc, TA = TL to TH, ATD Clock = 2 MHz, unless otherwise noted
Characteristic
Symbol
Min
Max
Unit
Analog supply voltage
VDDA
4.5
5.5
V
Analog supply currentNormal operation
IDDA
1.0
mA
Reference voltage, low
VRL
VSSA
VDDA/2
V
Reference voltage, high
VRH
VDDA/2
VDDA
V
VRH−VRL
4.5
5.5
V
VINDC
VSSA
VDDA
V
VREF differential reference voltage(1)
Input voltage(2)
Input current, off channel(3)
IOFF
100
nA
Reference supply current
IREF
250
µA
Input capacitanceNot Sampling
Sampling
CINN
CINS
10
15
pF
pF
1. Accuracy is guaranteed at VRH − VRL = 5.0V ±10%.
2. To obtain full-scale, full-range results, VSSA ≤ VRL ≤ VINDC ≤ VRH ≤ VDDA.
3. Maximum leakage occurs at maximum operating temperature. Current decreases by approximately one-half for each 10°C
decrease from maximum temperature.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
389
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Electrical Specifications
Table 19-6. Analog Converter Characteristics (Operating)
VDD = 5.0 Vdc ±10%, VSS = 0 Vdc, TA = TL to TH, ATD Clock = 2 MHz, unless otherwise noted
Characteristic
8-bit resolution(1)
Symbol
Min
1 count
Typical
Max
20
Unit
mV
8-bit differential non-linearity(2)
DNL
−0.5
+0.5
count
8-bit integral non-linearity(2)
INL
−1
+1
count
8-bit absolute error,(3)2, 4, 8, and 16 ATD sample clocks
AE
−1
+1
count
10-bit resolution(1)
1 count
5
mV
10-bit differential non-linearity(2)
DNL
–2
2
count
10-bit integral non-linearity(2)
INL
–2
2
count
10-bit absolute error(3) 2, 4, 8, and 16 ATD sample clocks
AE
–2.5
2.5
count
Maximum source impedance
RS
See
note(4)
KΩ
20
1. VRH − VRL ≥ 5.12V; VDDA − VSSA = 5.12V
2. At VREF = 5.12V, one 8-bit count = 20 mV, and one 10-bit count = 5mV.
INL and DNL are characterized using the process window parameters affecting the ATD accuracy, but they are not tested.
3. These values include quantization error which is inherently 1/2 count for any A/D converter.
4. Maximum source impedance is application-dependent. Error resulting from pin leakage depends on junction leakage into
the pin and on leakage due to charge-sharing with internal capacitance.
Error from junction leakage is a function of external source impedance and input leakage current. Expected error in result
value due to junction leakage is expressed in voltage (VERRJ):
VERRJ = RS × IOFF
where IOFF is a function of operating temperature. Charge-sharing effects with internal capacitors are a function of ATD clock
speed, the number of channels being scanned, and source impedance. Charge pump leakage is computed as follows:
VERRJ = .25pF × VDDA × RS × ATDCLK/(8 × number of channels)
Technical Data
390
MC68HC912DG128 — Rev 3.0
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Electrical Specifications
Tables of Data
Table 19-7. ATD AC Characteristics (Operating)
VDD = 5.0 Vdc ±10%, VSS = 0 Vdc, TA = TL to TH, ATD Clock = 2 MHz, unless otherwise noted
Characteristic
Symbol
Min
Max
Unit
MCU clock frequency (p-clock)
fPCLK
2.0
8.0
MHz
ATD operating clock frequency
fATDCLK
0.5
2.0
MHz
ATD 8-Bit conversion period
clock cycles(1)
conversion time(2)
nCONV8
tCONV8
18
9
32
16
cycles
µs
ATD 10-Bit conversion period
clock cycles(1)
conversion time(2)
nCONV10
tCONV10
20
10
34
17
cycles
µs
10
µs
Stop and ATD power up recovery time(3)
VDDA = 5.0V
tSR
1. The minimum time assumes a final sample period of 2 ATD clock cycles while the maximum time assumes a final sample
period of 16ATD clocks.
2. This assumes an ATD clock frequency of 2.0MHz.
3. From the time ADPU is asserted until the time an ATD conversion can begin.
Table 19-8. ATD Maximum Ratings
Characteristic
Symbol
Value
Units
ATD reference voltage
VRH ≤ VDDA
VRL ≥ VSSA
VRH
VRL
−0.3 to +6.5
−0.3 to +6.5
V
V
VSS differential voltage
|VSS−VSSA|
0.1
V
VDD differential voltage
VDD−VDDA
VDDA−VDD
6.5
0.3
V
V
VREF differential voltage
|VRH−VRL|
6.5
V
|VRH−VDDA|
6.5
V
Reference to supply differential voltage
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
391
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Electrical Specifications
Table 19-9. EEPROM Characteristics
VDD = 5.0 Vdc ±10%, VSS = 0 Vdc, TA = TL to TH, unless otherwise noted
Characteristic
Symbol
Min
Minimum programming clock frequency(1)
fPROG
1.0
Programming time
tPROG
10
Typical
tERASE
Write/erase endurance
10
10.5
ms
tPROG+ 1
ms
10.5
ms
30,000(2)
10,000
Data retention
Unit
MHz
Clock recovery time, following STOP, to continue programming tCRSTOP
Erase time
Max
10
cycles
10.5
years
1. RC oscillator must be enabled if programming is desired and fSYS < fPROG.
2. If average TH is below 85° C.
Table 19-10. Flash EEPROM Characteristics
VDD = 5.0 Vdc ±10%, VSS = 0 Vdc, TA = TL to TH, unless otherwise noted
Characteristic
Symbol
Min
Typical
Max
Units
Program/erase supply voltage:
Read only
Program / erase / verify
VFP
VDD−0.35
11.4
VDD
12
VDD+0.5
12.6
V
V
Program/erase supply current
Word program(VFP = 12V)
Erase(VFP = 12V)
IFP
30
4
mA
mA
Number of programming pulses
nPP
50
pulses
25
µs
Programming pulse
tPPULSE
20
Program to verify time
tVPROG
10
µs
Program margin
pm
100(1)
%
Number of erase pulses
nEP
5
pulses
10
ms
Erase pulse
tEPULSE
5
Erase to verify time
tVERASE
1
ms
em
100(1)
%
Program/erase endurance
100
cycles
Data retention
10
years
Erase margin
—
1. The number of margin pulses required is the same as the number of pulses used to program or erase.
Technical Data
392
MC68HC912DG128 — Rev 3.0
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Electrical Specifications
Tables of Data
Freescale Semiconductor, Inc...
Use of an external circuit to condition VFP is recommended. Figure 19-1
shows a simple circuit that maintains required voltages and filters
transients. VFP is pulled to VDD via Schottky diode D2. Application of
programming voltage via diode reverse-biases D2, protecting VDD from
excessive reverse current. D2 also protects the FLASH from damage
should programming voltage go to 0. Programming power supply
voltage must be adjusted to compensate for the forward-bias drop
across D1. The charge time constant of R1 and C1 filters transients,
while R2 provides a discharge bleed path to C1. Allow for RC charge and
discharge time constants when applying and removing power. When
using this circuit, keep leakage from external devices connected to the
VFP pin low, to minimize diode voltage drop.
PROGRAMMING VOLTAGE
POWER SUPPLY
D1
R1
10Ω
4.5V
D2
VFP
VDD
PIN
R2
22kΩ
C1
0.1µF
Figure 19-1. VFP Conditioning Circuit
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
393
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Electrical Specifications
30ns MAXIMUM
13.5V
12.8V
VFP ENVELOPE
VDD ENVELOPE
11.4V
COMBINED VDD AND VFP
tER
6.5V
4.5V
4.15V
0V
–0.30V
POWER
ON
NORMAL
READ
PROGRAM
ERASE
VERIFY
POWER
DOWN
Figure 19-2. VFP Operating Range
Table 19-11. Pulse Width Modulator Characteristics
VDD = 5.0 Vdc ±10%, VSS = 0 Vdc, TA = TL to TH, unless otherwise noted
Characteristic
Symbol
Min
Max
Unit
E-clock frequency
feclk
0.004
8.0
MHz
A-clock frequency
Selectable
faclk
feclk
Hz
B-clock frequency
Selectable
fbclk
feclk
Hz
Left-aligned PWM frequency
8-bit
16-bit
flpwm
feclk/1M
feclk/256M
feclk/2
feclk/2
Hz
Hz
Left-aligned PWM resolution
rlpwm
feclk/4K
feclk
Hz
Center-aligned PWM frequency
8-bit
16-bit
fcpwm
feclk/2M
feclk/512M
feclk
feclk
Hz
Hz
Center-aligned PWM resolution
rcpwm
feclk/4K
feclk
Hz
feclk/128
feclk/128
Technical Data
394
MC68HC912DG128 — Rev 3.0
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Electrical Specifications
Tables of Data
Table 19-12. Control Timing
8.0 MHz
Characteristic
Symbol
Unit
Min
Max
fo
0.004
8.0
MHz
E-clock period
tcyc
0.125
250
µs
External oscillator frequency
feo
0.5
16.0(1)
MHz
Processor control setup time
tPCSU = tcyc/2+ 20
tPCSU
82
—
PWRSTL
32
2
—
—
tcyc
tcyc
Mode programming setup time
tMPS
4
—
tcyc
Mode programming hold time
tMPH
10
—
ns
PWIRQ
270
—
ns
tWRS
—
4
cycles
PWTIM
270
—
ns
Frequency of operation
Reset input pulse width
To guarantee external reset vector
Minimum input time (can be preempted by internal reset)
Interrupt pulse width, IRQ edge-sensitive mode
PWIRQ = 2tcyc + 20
Wait recovery startup time
Timer input capture pulse width (PWTIM = 2 tcyc + 20)
ns
1. When using a quartz crystal, operation should be restricted to 8MHz.
1. RESET is recognized during the first clock cycle it is held low. Internal circuitry then drives
the pin low for 16 clock cycles, releases the pin, and samples the pin level 8 cycles later
to determine the source of the interrupt.
PT[7:0]1
PWTIM
PT[7:0]2
PT71
PWPA
PT72
NOTES:
1. Rising edge sensitive input
2. Falling edge sensitive input
Figure 19-3. Timer Inputs
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
395
Freescale Semiconductor, Inc.
NOTE: Reset timing is subject to change.
INTERNAL
ADDRESS
MODA, MODB
RESET
ECLK
EXTAL
VDD
4098 tcyc
FFFE
FFFE
FREE
1ST
PIPE
2ND
PIPE
3RD
PIPE
tPCSU
1ST
EXEC
FFFE
PWRSTL
tMPS
FFFE
FFFE
Freescale Semiconductor, Inc...
tMPH
FREE
1ST
PIPE
2ND
PIPE
3RD
PIPE
1ST
EXEC
Electrical Specifications
Figure 19-4. POR and External Reset Timing Diagram
Technical Data
396
MC68HC912DG128 — Rev 3.0
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
MOTOROLA
MC68HC912DG128 — Rev 3.0
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
SP-6
SP-6
SP-8
SP-8
SP-9
SP-9
PWIRQ
NOTES:
1. Edge Sensitive IRQ pin (IRQE bit = 1)
2. Level sensitive IRQ pin (IRQE bit = 0)
3. tSTOPDELAY = 4098 tcyc if DLY bit = 1 or 2 tcyc if DLY = 0.
4. XIRQ with X bit in CCR = 1.
5. IRQ or (XIRQ with X bit in CCR = 0).
ADDRESS5
ADDRESS4
ECLK
IRQ
or XIRQ
IRQ1
INTERNAL
CLOCKS
tSTOPDELAY3
FREE
FREE
OPT
FETCH
1ST
EXEC
FREE
1ST
PIPE
2ND
PIPE
3RD
PIPE
1ST
EXEC
Resume program with instruction which follows the STOP instruction.
VECTOR
FREE
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Electrical Specifications
Tables of Data
Figure 19-5. STOP Recovery Timing Diagram
Technical Data
397
398
Technical Data
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
SP – 2
NOTE: RESET also causes recovery from WAIT.
R/W
ADDRESS
IRQ, XIRQ,
OR INTERNAL
INTERRUPTS
ECLK
SP – 6 . . . SP – 9
PC, IY, IX, B:A, , CCR
STACK REGISTERS
SP – 4
SP – 9
SP – 9 . . . SP – 9
SP – 9
tPCSU
VECTOR
ADDRESS
tWRS
FREE
Freescale Semiconductor, Inc...
1ST
PIPE
2ND
PIPE
3RD
PIPE
1ST
EXEC
Freescale Semiconductor, Inc.
Electrical Specifications
Figure 19-6. WAIT Recovery Timing Diagram
MC68HC912DG128 — Rev 3.0
MOTOROLA
MOTOROLA
VECT
DATA
MC68HC912DG128 — Rev 3.0
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
NOTES:
1. Edge sensitive IRQ pin (IRQE bit = 1)
2. Level sensitive IRQ pin (IRQE bit = 0)
R/W
VECTOR
ADDR
PWIRQ
tPCSU
ADDRESS
OR INTERNAL
INTERRUPT
IRQ2, XIRQ,
IRQ1
ECLK
PC
SP – 2
PROG
FETCH
1ST
PIPE
IY
SP – 4
IX
SP – 6
PROG
FETCH
2ND
PIPE
B:A
SP – 8
CCR
SP – 9
PROG
FETCH
3RD
PIPE
Freescale Semiconductor, Inc...
1ST
EXEC
Freescale Semiconductor, Inc.
Electrical Specifications
Tables of Data
Figure 19-7. Interrupt Timing Diagram
Technical Data
399
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Electrical Specifications
Table 19-13. Peripheral Port Timing
8.0 MHz
Characteristic
Symbol
Unit
Min
Max
fo
0.004
8.0
MHz
tcyc
0.125
250
µs
Peripheral data setup time (tPDSU = tcyc/2 + 40)
MCU read of ports
tPDSU
102
—
ns
Peripheral data hold time
MCU read of ports
tPDH
0
—
ns
Delay time, peripheral data write
MCU write to ports
tPWD
—
40
ns
Frequency of operation (E-clock frequency)
E-clock period
MCU READ OF PORT
ECLK
tPDSU
tPDH
PORTS
PORT RD TIM
Figure 19-8. Port Read Timing Diagram
MCU WRITE TO PORT
ECLK
tPWD
PORT A
PREVIOUS PORT DATA
NEW DATA VALID
PORT WR TIM
Figure 19-9. Port Write Timing Diagram
Technical Data
400
MC68HC912DG128 — Rev 3.0
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Electrical Specifications
Tables of Data
Table 19-14. Multiplexed Expansion Bus Timing
VDD = 5.0 Vdc ± 10%, VSS = 0 Vdc, TA = TL to TH, unless otherwise noted
Characteristic(1),
Num
(2), (3), (4)
Delay
Symbol
Frequency of operation (E-clock frequency)
8 MHz
Unit
Min
Max
fo
0.004
8.0
MHz
250
µs
1
Cycle timetcyc = 1/fo
—
tcyc
0.125
2
Pulse width, E lowPWEL = tcyc/2 + delay
−4
PWEL
58
ns
3
Pulse width, E high(5)PWEH = tcyc/2 + delay
−2
PWEH
60
ns
5
Address delay timetAD = tcyc/4 + delay
27
tAD
7
Address valid time to ECLK risetAV = PWEL − tAD
—
tAV
0
ns
8
Multiplexed address hold timetMAH = tcyc/4 + delay
−18
tMAH
13
ns
9
Address Hold to Data Valid
—
tAHDS
20
10
Data Hold to High ZtDHZ = tAD − 20
—
tDHZ
11
Read data setup time
—
tDSR
25
ns
12
Read data hold time
—
tDHR
10
ns
13
Write data delay time
—
tDDW
14
Write data hold time
—
tDHW
20
ns
15
Write data setup time(5)tDSW = PWEH − tDDW
—
tDSW
13
ns
16
Read/write delay timetRWD = tcyc/4 + delay
18
tRWD
17
Read/write valid time to E risetRWV = PWEL − tRWD
—
tRWV
9
ns
18
Read/write hold time
—
tRWH
20
ns
19
Low strobe(6) delay timetLSD = tcyc/4 + delay
18
tLSD
20
Low strobe(6) valid time to E risetLSV = PWEL − tLSD
—
tLSV
9
ns
21
Low strobe(6) hold time
—
tLSH
20
ns
22
Address access time(5)tACCA = tcyc − tAD − tDSR
—
tACCA
42
ns
23
Access time from E rise(5)tACCE = PWEH − tDSR
—
tACCE
35
ns
24
DBE delay from ECLK rise(5)tDBED = tcyc/4 + delay
8
tDBED
39
ns
25
DBE valid timetDBE = PWEH − tDBED
—
tDBE
21
26
DBE hold time from ECLK fall
tDBEH
–3
58
ns
38
47
49
49
ns
ns
ns
ns
10
ns
1. All timings are calculated for normal port drives.
2. Crystal input is required to be within 45% to 55% duty.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
401
Freescale Semiconductor, Inc.
Electrical Specifications
3. Reduced drive must be off to meet these timings.
4. Unequalled loading of pins will affect relative timing numbers.
5. This characteristic is affected by clock stretch.
Add N × tcyc where N = 0, 1, 2, or 3, depending on the number of clock stretches.
6. Without TAG enabled.
1
2
3
Freescale Semiconductor, Inc...
ECLK
16
17
18
19
20
21
R/W
LSTRB
(W/O TAG ENABLED)
5
23
7
11
22
10
READ
12
ADDRESS
ADDRESS/DATA
MULTIPLEXED
DATA
9
8
13
WRITE
ADDRESS
15
14
DATA
24
25
26
DBE
NOTE: Measurement points shown are 20% and 70% of VDD
Figure 19-10. Multiplexed Expansion Bus Timing Diagram
Technical Data
402
MC68HC912DG128 — Rev 3.0
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Electrical Specifications
Tables of Data
Table 19-15. SPI Timing
(VDD = 5.0 Vdc ±10%, VSS = 0 Vdc, TA = TL to TH , 200 pF load on all SPI pins)(1)
Function
Symbol
Min
Max
Unit
Operating Frequency
Master
Slave
fop
1/256
1/256
1/2
1/2
feclk
SCK Period
Master
Slave
tsck
2
2
256
—
tcyc
tcyc
Enable Lead Time
Master
Slave
tlead
1/2
1
—
—
tsck
tcyc
Enable Lag Time
Master
Slave
tlag
1/2
1
—
—
tsck
tcyc
twsck
tcyc − 30
tcyc − 30
128 tcyc
—
ns
ns
Sequential Transfer Delay
Master
Slave
ttd
1/2
1
—
—
tsck
tcyc
Data Setup Time (Inputs)
Master
Slave
tsu
30
30
—
—
ns
ns
Data Hold Time (Inputs)
Master
Slave
thi
0
30
—
—
ns
ns
Slave Access Time
ta
—
1
tcyc
Slave MISO Disable Time
tdis
—
1
tcyc
Data Valid (after SCK Edge)
Master
Slave
tv
—
—
50
50
ns
ns
Data Hold Time (Outputs)
Master
Slave
tho
0
0
—
—
ns
ns
Rise Time
Input
Output
tri
tro
—
—
tcyc − 30
30
ns
ns
Fall Time
Input
Output
tfi
tfo
—
—
tcyc − 30
30
ns
ns
Num
Clock (SCK) High or Low Time
Master
Slave
1. All AC timing is shown with respect to 20% VDD and 70% VDD levels unless otherwise noted.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
403
Freescale Semiconductor, Inc.
Electrical Specifications
SS1
(OUTPUT)
5
2
1
SCK
(CPOL = 0)
(OUTPUT)
4
13
SCK
(CPOL = 1)
(OUTPUT)
6
Freescale Semiconductor, Inc...
3
12
4
7
MISO
(INPUT)
MSB IN2
BIT 6 .
10
. .
1
LSB IN
10
MOSI
(OUTPUT)
MSB OUT2
11
BIT 6 .
. .
1
LSB OUT
1.
SS output mode (DDS7 = 1, SSOE = 1).
2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB.
A) SPI Master Timing (CPHA = 0)
SS1
(OUTPUT)
5
1
2
13
12
12
13
3
SCK
(CPOL = 0)
(OUTPUT)
4
4
SCK
(CPOL = 1)
(OUTPUT)
6
MISO
(INPUT)
7
MSB IN2
. . .
1
LSB IN
11
10
MOSI
(OUTPUT) PORT DATA
BIT 6
MASTER MSB OUT2
BIT 6 .
. .
1
MASTER LSB OUT
PORT DATA
1.
SS output mode (DDS7 = 1, SSOE = 1).
2. LSBF = 0. For LSBF = 1, bit order is LSB, bit 1, ..., bit 6, MSB.
B) SPI Master Timing (CPHA = 1)
Figure 19-11. SPI Timing Diagram (1 of 2)
Technical Data
404
MC68HC912DG128 — Rev 3.0
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Electrical Specifications
Tables of Data
SS
(INPUT)
5
1
13
12
12
13
3
SCK
(CPOL = 0)
(INPUT)
4
2
4
SCK
(CPOL = 1)
(INPUT)
9
8
MISO
(OUTPUT)
10
6
MOSI
(INPUT)
BIT 6
MSB OUT
SLAVE
11
11
. . .
1
SLAVE LSB OUT
SEE
NOTE
7
BIT 6
MSB IN
. . .
1
LSB IN
NOTE: Not defined but normally MSB of character just received.
A) SPI Slave Timing (CPHA = 0)
SS
(INPUT)
5
3
1
2
13
12
12
13
SCK
(CPOL = 0)
(INPUT)
4
4
SCK
(CPOL = 1)
(INPUT)
11
10
MISO
(OUTPUT)
SEE
NOTE
8
MOSI
(INPUT)
SLAVE
MSB OUT
6
BIT 6 .
9
. .
1
SLAVE LSB OUT
7
MSB IN
BIT 6
. . .
1
LSB IN
NOTE: Not defined but normally LSB of character just received.
SPI SLAVE CPHA1
B) SPI Slave Timing (CPHA = 1)
Figure 19-12. SPI Timing Diagram (2 of 2)
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
405
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Electrical Specifications
Table 19-16. CGM Characteristics
5.0 Volts +/- 10%
Characteristic
Symbol
Min.
PLL reference frequency, crystal oscillator range
fREF
Bus frequency
VCO range
Max.
Unit
0.5
8
MHz
fBUS
0.004
8
MHz
fVCO
2.5
8
MHz
fVCOMIN
0.5
2.5
MHz
∆trk
3%
4%
—
∆Lock
0%
1.5%
—
Un-Lock Detection
∆unl
0.5%
2.5%
—
Lock Detector transition from Tracking to
Acquisition mode
∆unt
6%
8%
—
Minimum leakage resistance on crystal oscillator
pins
rleak
1
VCO Limp-Home frequency
Lock Detector transition from Acquisition to
Tracking mode(1)
Lock Detection
Typ.
MΩ
PLL Stabilization delay(2)
PLL Total Stabilization Delay(3)
tstab
3
ns
PLLON Acquisition mode stabilization delay.(3)
tacq
1
ns
tal
2
ns
PLLON tracking mode stabilization delay.(3)
1. AUTO bit set
2. PLL stabilization delay is highly dependent on operational requirement and external component values (e.e. crystal, XFC
filter component values|). Note (3) shows typical delay values for a typical configuration. Appropriate XFC filter values
should be chosen based on operational requirement of system.
3. fREF = 4MHz, fBUS = 8MHz (REFDV = #$00, SYNR = #$01), XFC:Cs = 33nF, Cp = 3.3nF, Rs = 2.7KΩ.
Table 19-17. Key Wake-up
Characteristic
STOP Key Wake-Up Filter time
Key Wake-Up Single Pulse Time Interval
Symbol
tKWSTP
Min.
2
tKWSP
20
Max.
10
Unit
µs
µs
Table 19-18. msCAN12 Wake-up Time from Sleep Mode
VDD = 5.0V dc ± 10%, VSS = 0 Vdc, TA = TL to TH, unless otherwise noted
Characteristic
Wake-Up time
Symbol
twup
Min.
2
Technical Data
406
Max.
5
Unit
µs
MC68HC912DG128 — Rev 3.0
Electrical Specifications
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Section 20. Appendix: CGM Practical Aspects
20.1 Contents
20.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 407
20.3
A Few Hints For The CGM Crystal Oscillator Application. . . . 407
20.4
Practical Aspects For The PLL Usage . . . . . . . . . . . . . . . . . . 410
20.5
Printed Circuit Board Guidelines. . . . . . . . . . . . . . . . . . . . . . . 415
20.2 Introduction
This sections provides useful and practical pieces of information
concerning the implementation of the CGM module.
20.3 A Few Hints For The CGM Crystal Oscillator Application
20.3.1 What Loading Capacitors To Choose?
First, from small-signal analysis, it is known that relatively large values
for C1 and C2 have a positive impact on the phase margin. However, the
higher loading they represent decreases the loop gain. Alternatively,
small values for these capacitors will lead to higher open loop gain, but
as the frequency of oscillation approaches the parallel resonance, the
phase margin, and consequently the ability to start-up correctly, will
decrease. From this it is clear that relatively large capacitor values
(>33pF), are reserved for low frequency crystals in the MHz range.
NOTE:
Using the recommended loading capacitor CL value from the crystal
manufacturer is a good starting point. Taking into account unavoidable
strays, this equates to about (CL-2pF).
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Appendix: CGM Practical Aspects
For More Information On This Product,
Go to: www.freescale.com
407
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Appendix: CGM Practical Aspects
Theoretically speaking, nothing precludes the use of non-identical
values for C1 and C2. As this complicate a bit the management of the
final board device list, this is not recommended. However, if
asymmetrical capacitors are chosen, the value of C1 should be higher
than C2 (because the reflected loading is proportional to the square of
the impedance of C2).
20.3.2 DC Bias
Due to the nature of the translated ground Colpitts oscillator a DC
voltage bias is applied to the crystal.
Please contact the crystal manufacturer for specific DC bias conditions
and recommended capacitance value (if applicable).
20.3.3 What Is the Final Oscillation Frequency?
The exact calculation is not straightforward as it takes into account the
resonator characteristics and the loading capacitors values as well as
internal design parameters which can vary with Process Voltage
Temperature (PVT) conditions. Nevertheless, if L is the series
inductance, R is the series resistance, C is the series capacitance and
Cc the parallel capacitance of the crystal, we can then use the following
simplified equation:
1
1
1
Fosc = ------ ⋅ -------- + ---------------------------------------------2 π LC L ⋅ ( Cc + C1 || C2 )
C1=C2=Cl yields to
1
1
1
Fosc = ------ ⋅ -------- + --------------------------------------2 π LC L ⋅ ( Cc + Cl ⁄ 2 )
20.3.4 How Do I Control The Peak to Peak Oscillation Amplitude?
The CGM oscillator is equipped with an Amplitude Limitation Control
loop which integrates the peak to peak ‘extal’ amplitude and in return
reduces the steady current of the transconductor device until a stable
Technical Data
408
MC68HC912DG128 — Rev 3.0
Appendix: CGM Practical Aspects
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Appendix: CGM Practical Aspects
A Few Hints For The CGM Crystal Oscillator Application
quiescent point is reached. Controlling this final peak to peak amplitude
can be performed by three means:
1. Reducing the values of C1 and C2. This decreases the loading so
that the necessary gm value required to sustain oscillation can be
smaller. The consequently smaller current will be reached with a
larger ‘extal’ swing.
2. Using VDDPLL=VSS (i.e. shutting off the PLL). Doing so
increases the starting current by approximately 50%. All other
parameters staying the same, a larger ‘extal’ swing will be required
to reduce this starting current to its quiescent value.
3. Also, placing a high value resistor (>1MΩ) across the EXTAL and
XTAL pins significantly increased the oscillation amplitude.
Because this complicates the design analysis as it transforms a
pure susceptance jωC1 into a complex admittance G+jωC1,
Motorola cannot promote this application trick.
20.3.5 What Do I Do In Case The Oscillator Does Not Start-up?
1. First, verify that the application schematic respects the principle of
operation, i.e. crystal mounted between EXTAL and VSS,
Capacitor C1 between XTAL and EXTAL, Capacitor C2 between
XTAL and VSS, nothing else. This is not the conventional MCU
application schematic of the Pierce oscillator as it can be seen on
other HC12 derivatives!
2. Re-consider the choice of the tuning capacitors.
3. The oscillator circuitry is powered internally from a core VDD pad
and the return path is the VSSPLL pad. Verify on the application
PCB the correct connection of these pads (especially VSSPLL),
but also verify the waveform of the VDD voltage as it is imposed
on the pad. Sometimes external components (for instance choke
inductors), can cause oscillations on the power line. This is of
course detrimental to the oscillator circuitry.
4. If possible, consider using a resonator with built-in tuning
capacitors. They may offer better performances with respect to
their discrete elements implementation.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Appendix: CGM Practical Aspects
For More Information On This Product,
Go to: www.freescale.com
409
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Appendix: CGM Practical Aspects
20.4 Practical Aspects For The PLL Usage
20.4.1 Synthesized Bus Frequency
Starting from a ceramic resonator or quartz crystal frequency FXTAL, if
‘refdv’ and ‘synr’ are the decimal content of the REFDV and SYNR
registers respectively, then the MCU bus frequency will simply be:
F XTAL ⋅ ( synr + 1 )
F BUS = F VCO = -----------------------------------------------( refdv + 1 )
synr ∈ { 0,1,2,3...63}
refdv ∈ { 0,1,2,3...7}
NOTE:
It is not allowed to synthesize a bus frequency that is lower than the
crystal frequency, as the correct functioning of some internal
synchronizers would be jeopardized (e.g. the MCLK and XCLK clock
generators).
20.4.2 Operation Under Adverse Environmental Conditions
The normal operation for the PLL is the so-called ‘automatic bandwidth
selection mode’ which is obtained by having the AUTO bit set in the
PLLCR register. When this mode is selected and as the VCO frequency
approaches its target, the charge pump current level will automatically
switch from a relatively high value of around 40 µA to a lower value of
about 3 µA. It can happen that this low level of charge pump current is
not enough to overcome leakages present at the XFC pin due to adverse
environmental conditions. These conditions are frequently encountered
for uncoated PCBs in automotive applications. The main symptom for
this failure is an unstable characteristic of the PLL which in fact ‘hunts’
between acquisition and tracking modes. It is then advised for the
running software to place the PLL in manual, forced acquisition mode by
clearing both the AUTO and the ACQ bits in the PLLCR register. Doing
so will maintain the high current level in the charge pump constantly and
will permit to sustain higher levels of leakages at the XFC pin. This latest
revision of the Clock Generator Module maintains the lock detection
Technical Data
410
MC68HC912DG128 — Rev 3.0
Appendix: CGM Practical Aspects
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Appendix: CGM Practical Aspects
Practical Aspects For The PLL Usage
feature even in manual bandwidth control, offering then to the
application software the same flexibility for the clocking control as the
automatic mode.
20.4.3 Filter Components Selection Guide
20.4.3.1 Equations Set
Freescale Semiconductor, Inc...
These equations can be used to select a set of filter components. Two
cases are considered:
1. The ‘tracking’ mode. This situation is reached normally when the
PLL operates in automatic bandwidth selection mode (AUTO=1 in
the PLLCR register).
2. The ‘acquisition’ mode. This situation is reached when the PLL
operates in manual bandwidth selection mode and forced
acquisition (AUTO=0, ACQ=0 in the PLLCR register).
In both equations, the power supply should be 5V. Start with the target
loop bandwidth as a function of the other parameters, but obviously,
nothing prevents the user from starting with the capacitor value for
example. Also, remember that the smoothing capacitor is always
assumed to be one tenth of the series capacitance value.
So with:
m:
R:
C:
Fbus:
ζ:
Fc:
the multiplying factor for the reference frequency (i.e. (synr+1))
the series resistance of the low pass filter in Ω
the series capacitance of the low pass filter in nF
the target bus frequency expressed in MHz
the desired damping factor
the desired loop bandwidth expressed in Hz
for the ‘tracking’ mode:
9
2
– F bus
 1.675
-----------------------------
 10.795 
2 ⋅ 10 ⋅ ζ
⋅R
37.78 ⋅ e
F c = ------------------------- = -----------------------------------------------------π⋅R⋅C
2⋅π⋅m
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Appendix: CGM Practical Aspects
For More Information On This Product,
Go to: www.freescale.com
411
Freescale Semiconductor, Inc.
Appendix: CGM Practical Aspects
and for the ‘acquisition’ mode:
9
2
– F bus
 1.675
-----------------------------
 10.795 
415.61 ⋅ e
2 ⋅ 10 ⋅ ζ
⋅R
F c = ------------------------- = --------------------------------------------------------π⋅R⋅C
2⋅π⋅m
20.4.3.2 Particular Case of an 8MHz Synthesis
Freescale Semiconductor, Inc...
Assume that a desired value for the damping factor of the second order
system is close to 0.9 as this leads to a satisfactory transient response.
Then, derived from the equations above, Table 20-1 and Table 20-2
suggest sets of values corresponding to several loop bandwidth
possibilities in the case of an 8MHz synthesis for the two cases
mentioned above.
The filter components values are chosen from standard series (e.g. E12
for resistors). The operating voltage is assumed to be 5V (although there
is only a minor difference between 3V and 5V operation). The smoothing
capacitor Cp in parallel with R0 and C0 is set to be 1/10 of the value of
C0. The reference frequencies mentioned in this table correspond to the
output of the fine granularity divider controlled by the REFDV register.
This means that the calculations are irrespective of the way the
reference frequency is generated (directly for the crystal oscillator or
after division). The target frequency value also has an influence on the
calculations of the filter components because the VCO gain is NOT
constant over its operating range.
The bandwidth limit corresponds to the so-called Gardner’s criteria. It
corresponds to the maximum value that can be chosen before the
continuous time approximation ceases to be justified. It is of course
advisable to stay far away from this limit.
Technical Data
412
MC68HC912DG128 — Rev 3.0
Appendix: CGM Practical Aspects
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Appendix: CGM Practical Aspects
Practical Aspects For The PLL Usage
Table 20-1. Suggested 8MHz Synthesis PLL Filter Elements (Tracking Mode)
Reference [MHz]
SYNR
Fbus [MHz]
C0
[nF]
R0
[kΩ]
Cp
[kΩ]
Loop
Bandwidth
[kHz]
Bandwidth
Limit [kHz]
0.614
$0C
7.98
100
4.3
10
1.1
157
0.614
$0C
7.98
4.7
20
0.47
5.3
157
0.614
$0C
7.98
1
43
0.1
11.5
157
0.614
$0C
7.98
0.33
75
0.033
20
157
0.8
$09
8.00
220
2.7
22
0.9
201
0.8
$09
8.00
10
12
1.0
4.2
201
0.8
$09
8.00
2.2
27
0.22
8.6
201
0.8
$09
8.00
0.47
56
0.047
19.2
201
1
$07
8.00
220
2.4
22
1
251
1
$07
8.00
10
11
1.0
4.7
251
1
$07
8.00
2.2
24
0.22
9.9
251
1
$07
8.00
0.47
51
0.047
21.4
251
1.6
$05
8.00
330
1.5
33
1
402
1.6
$05
8.00
10
9.1
1.0
5.9
402
1.6
$05
8.00
3.3
15
0.33
10.2
402
1.6
$05
8.00
1
27
0.1
18.6
402
2
$03
8.00
470
1.1
47
0.96
502
2
$03
8.00
22
5.1
2.2
4.4
502
2
$03
8.00
4.7
11
0.47
9.6
502
2
$03
8.00
1
24
0.1
20.8
502
2.66
$02
8.00
220
1.5
22
1.6
668
2.66
$02
8.00
22
4.7
2.2
5.1
668
2.66
$02
8.00
4.7
10
0.47
11
668
2.66
$02
8.00
1
22
0.1
24
668
4
$01
8.00
220
1.2
22
1.98
1005
4
$01
8.00
33
3
3.3
5.1
1005
4
$01
8.00
10
5.6
1.0
9.3
1005
4
$01
8.00
2.2
12
0.22
19.8
1005
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Appendix: CGM Practical Aspects
For More Information On This Product,
Go to: www.freescale.com
413
Freescale Semiconductor, Inc.
Appendix: CGM Practical Aspects
Freescale Semiconductor, Inc...
Table 20-2. Suggested 8MHz Synthesis PLL Filter Elements (Acquisition Mode)
Reference
[MHz]
SYNR
Fbus
[MHz]
C0 [nF]
R0 [kΩ]
Cp [nF]
Loop
Bandwidth
[kHz]
Bandwidth
Limit [kHz]
0.614
$0C
7.98
1000
0.43
100
1.2
157
0.614
$0C
7.98
47
2
4.7
5.5
157
0.614
$0C
7.98
10
4.3
1.0
12
157
0.614
$0C
7.98
3.3
7.5
0.33
21
157
0.8
$09
8.00
2200
0.27
220
0.9
201
0.8
$09
8.00
100
1.2
10
4.4
201
0.8
$09
8.00
22
2.4
2.2
9.3
201
0.8
$09
8.00
4.7
5.6
0.47
20.1
201
1
$07
8.00
2200
0.22
220
1
251
1
$07
8.00
100
1.0
10
4.8
251
1
$07
8.00
2.
2.2
2.2
10.4
251
1
$07
8.00
4.7
4.7
0.47
22.5
251
1.6
$05
8.00
3300
0.15
330
1.1
402
1.6
$05
8.00
100
0.82
10
6.2
402
1.6
$05
8.00
33
1.5
3.3
10.7
402
1.6
$05
8.00
10
2.7
1.0
19.5
402
2
$03
8.00
4700
0.1
470
1
502
2
$03
8.00
220
0.51
22
4.6
502
2
$03
8.00
47
1.0
4.7
10
502
2
$03
8.00
10
2.4
1.0
21.8
502
2.66
$02
8.00
2200
0.12
220
1.7
668
2.66
$02
8.00
220
0.43
22
5.3
668
2.66
$02
8.00
47
1.0
4.7
11.6
668
2.66
$02
8.00
10
2
1.0
25.1
668
4
$01
8.00
2200
0.1
220
2.1
1005
4
$01
8.00
330
0.27
33
5.4
1005
4
$01
8.00
100
0.51
10
9.7
1005
4
$01
8.00
22
1.0
2.2
20.8
1005
Technical Data
414
MC68HC912DG128 — Rev 3.0
Appendix: CGM Practical Aspects
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Appendix: CGM Practical Aspects
Printed Circuit Board Guidelines
20.5 Printed Circuit Board Guidelines
Freescale Semiconductor, Inc...
Printed Circuit Boards (PCBs) are the board of choice for volume
applications. If designed correctly, a very low noise system can be built
on a PCB with consequently good EMI/EMC performances. If designed
incorrectly, PCBs can be extremely noisy and sensitive modules, and
the CGM could be disrupted. Some common sense rules can be used to
prevent such problems.
•
Use a ‘star’ style power routing plan as opposed to a ‘daisy chain’.
Route power and ground from a central location to each chip
individually, and use the widest trace practical (the more the chip
draws current, the wider the trace). NEVER place the MCU at the
end of a long string of serially connected chips.
•
When using PCB layout software, first direct the routing of the
power supply lines as well as the CGM wires (crystal oscillator and
PLL). Layout constraints must be then reported on the other
signals and not on these ‘hot’ nodes. Optimizing the ‘hot’ nodes at
the end of the routing process usually gives bad results.
•
Avoid notches in power traces. These notches not only add
resistance (and are not usually accounted for in simulations), but
they can also add unnecessary transmission line effects.
•
Avoid ground and power loops. This has been one of the most
violated guidelines of PCB layout. Loops are excellent noise
transmitters and can be easily avoided. When using multiple layer
PCBs, the power and ground plane concept works well but only
when strictly adhered to (do not compromise the ground plane by
cutting a hole in it and running signals on the ground plane layer).
Keep the spacing around via holes to a minimum (but not so small
as to add capacitive effects).
•
Be aware of the three dimensional capacitive effects of multilayered PCBs.
•
Bypass (decouple) the power supplies of all chips as close to the
chip as possible. Use one decoupling capacitor per power supply
pair (VDD/VSS, VDDX/VSSX...). Two capacitors with a ratio of
about 100 sometimes offer better performances over a broader
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Appendix: CGM Practical Aspects
For More Information On This Product,
Go to: www.freescale.com
415
Freescale Semiconductor, Inc.
Appendix: CGM Practical Aspects
Freescale Semiconductor, Inc...
spectrum. This is especially the case for the power supply pins
close to the E port, when the E clock and/or the calibration clock
are used.
•
On the general VDD power supply input, a ‘T’ low pass filter LCL
can be used (e.g. 10µH-47µF-10µH). The ‘T’ is preferable to the
‘Π’ version as the exhibited impedance is more constant with
respect to the VDD current. Like many modular micro controllers,
HC12 devices have a power consumption which not only varies
with clock edges but also with the functioning modes.
•
Keep high speed clock and bus trace length to a minimum. The
higher the clock speed, the shorter the trace length. If noisy
signals are sent over long tracks, impedance adjustments should
be considered at both ends of the line (generally, simple resistors
suffice).
•
Bus drivers like the CAN physical interface should be installed
close to their connector, with dedicated filtering on their power
supply.
•
Mount components as close to the board as possible. Snip excess
lead length as close to the board as possible. Preferably use
Surface Mount Devices (SMDs).
•
Mount discrete components as close to the chip that uses them as
possible.
•
Do not cross sensitive signals ON ANY LAYER. If a sensitive
signal must be crossed by another signal, do it as many layers
away as possible and at right angles.
•
Always keep PCBs clean. Solder flux, oils from fingerprints,
humidity and general dirt can conduct electricity. Sensitive circuits
can easily be disrupted by small amounts of leakage.
•
Choose PCB coatings with care. Certain epoxies, paints, gelatins,
plastics and waxes can conduct electricity. If the manufacturer
cannot provide the electrical characteristics of the substance, do
not use it.
Technical Data
416
MC68HC912DG128 — Rev 3.0
Appendix: CGM Practical Aspects
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Appendix: CGM Practical Aspects
Printed Circuit Board Guidelines
Freescale Semiconductor, Inc...
In addition to the above general pieces of advice, the following
guidelines should be followed for the CGM pins (but also more generally
for any sensitive analog circuitry):
•
Parasitic capacitance on EXTAL is absolutely critical – probably
the most critical layout consideration. The XTAL pin is not as
sensitive. All routing from the EXTAL pin through the resonator
and the blocking cap to the actual connection to VSS must be
considered.
•
For minimum capacitance there should ideally be no ground /
power plane around the EXTAL pin and associated routing.
However, practical EMC considerations obviously should be taken
into consideration for each application.
•
The clock input circuitry is sensitive to noise so excellent supply
routing and decoupling is mandatory. Connect the ground point of
the oscillator circuit directly to the VSSPLL pin.
•
Good isolation of PLL / Oscillator Power supply is critical. Use
1nF+ 100nF and keep tracks as low impedance as possible
•
Load capacitors should be low leakage and stable across
temperature – use NPO or C0G types.
•
The load capacitors may ‘pull’ the target frequency by a few ppm.
Crystal manufacturer specs show symmetrical values but the
series device capacitance on EXTAL and XTAL are not
symmetrical. It may be possible to adjust this by changing the
values of the load capacitors – start-up conditions should be
evaluated.
•
Keep the adjacent Port H / Port E and RESET signals noise free.
Don’t connect these to external signals and / or add series filtering
– a series resistor is probably adequate.
•
Any DC-blocking capacitor should be as low ESR as possible – for
the range of crystals we are looking at anything over 1 Ohm is too
much.
•
Mount oscillator components on MCU side of board – avoid using
vias in the oscillator circuitry.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Appendix: CGM Practical Aspects
For More Information On This Product,
Go to: www.freescale.com
417
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Appendix: CGM Practical Aspects
•
Mount the PLL filter and oscillator components as close to the
MCU as possible.
•
Do not allow the EXTAL and XTAL signals to interfere with the
XFC node. Keep these tracks as short as possible.
•
Do not cross the CGM signals with any other signal on any level.
•
Remember that the reference voltage for the XFC filter is
VDDPLL.
•
As the return path for the oscillator circuitry is VSSPLL, it is
extremely important to CONNECT VSSPLL to VSS even if the
PLL is not to be powered. Surface mount components reduce the
susceptibility of signal contamination.
•
Ceramic resonators with built-in capacitors are available. This is
an interesting solution because the parasitic components involved
are minimized due to the close proximity of the resonating
elements.
Technical Data
418
MC68HC912DG128 — Rev 3.0
Appendix: CGM Practical Aspects
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Section 21. Appendix: MC68HC912DG128A Flash
21.1 Contents
21.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 419
21.3
Overview. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420
21.4
Flash EEPROM Control Block . . . . . . . . . . . . . . . . . . . . . . . . 420
21.5
Flash EEPROM Arrays . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 420
21.6
Flash EEPROM Registers . . . . . . . . . . . . . . . . . . . . . . . . . . . 421
21.7
Operation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .423
21.8
Programming the Flash EEPROM . . . . . . . . . . . . . . . . . . . . . 424
21.9
Erasing the Flash EEPROM . . . . . . . . . . . . . . . . . . . . . . . . . . 425
21.10 Stop or Wait Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .425
21.2 Introduction
The four Flash EEPROM array modules 00FEE32K, 01FEE32K,
10FEE32K and 11FEE32K for the 68HC912DG128A serve as
electrically erasable and programmable, non-volatile ROM emulation
memory. The modules can be used for program code that must either
execute at high speed or is frequently executed, such as operating
system kernels and standard subroutines, or they can be used for static
data which is read frequently. The Flash EEPROM module is ideal for
program storage for single-chip applications allowing for field
reprogramming.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Appendix: MC68HC912DG128A Flash
For More Information On This Product,
Go to: www.freescale.com
419
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Appendix: MC68HC912DG128A Flash
21.3 Overview
Each 32K Flash EEPROM array is arranged in a 16-bit configuration and
may be read as either bytes, aligned words or misaligned words. Access
time is one bus cycle for byte and aligned word access and two bus
cycles for misaligned word operations.
Programming is by aligned word. The Flash EEPROM module supports
bulk erase only.
Each Flash EEPROM module has hardware interlocks which protect
stored data from accidental corruption. An erase- and programprotected 8-Kbyte block for boot routines is located at the top of each 32Kbyte array. Since boot programs must be available at all times, the only
useful boot block is at $E000–$FFFF location. All paged boot blocks can
be used as protected program space if desired.
21.4 Flash EEPROM Control Block
A 4-byte register block for each module controls the Flash EEPROM
operation. Configuration information is specified and programmed
independently from the contents of the Flash EEPROM array. At reset,
the 4-byte register section starts at address $00F4 and points to the
00FEE32K register block.
21.5 Flash EEPROM Arrays
After reset, a fixed 32K Flash EEPROM array, 11FEE32K, is located
from addresses $4000 to $7FFF and from $C000 to $FFFF. The other
three 32K Flash EEPROM arrays 00FEE32K, 01FEE32K and
10FEE32K, are mapped through a 16K byte program page window
located from addresses $8000 to $BFFF. The page window has eight
16K byte pages. The last two pages also map the physical location of the
fixed 32K Flash EEPROM array 11FEE32K. In expanded modes, the
Flash EEPROM arrays are turned off. See Operating Modes.
Technical Data
420
MC68HC912DG128 — Rev 3.0
Appendix: MC68HC912DG128A Flash
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Appendix: MC68HC912DG128A Flash
Flash EEPROM Registers
21.6 Flash EEPROM Registers
Each 32K byte Flash EEPROM module has a set of registers. The
register space $00F4-$00F7 is in a register space window of four pages.
Each register page of four bytes maps the register space for each Flash
module and each page is selected by the PPAGE register. See
Operating Modes.
FEELCK — Flash EEPROM Lock Control Register
RESET:
$00F4
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
LOCK
0
0
0
0
0
0
0
0
In normal modes the LOCK bit can only be written once after reset.
LOCK — Lock Register Bit
0 = Enable write to FEEMCR register
1 = Disable write to FEEMCR register
FEEMCR — Flash EEPROM Module Configuration Register
RESET:
$00F5
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
0
0
0
0
BOOTP
0
0
0
0
0
0
0
1
This register controls the operation of the Flash EEPROM array.
BOOTP cannot be changed when the LOCK control bit in the
FEELCK register is set or if ENPE in the FEECTL register is set.
BOOTP — Boot Protect
The boot blocks are located at $E000–$FFFF and $A000–$BFFF for
odd program pages for each Flash EEPROM module. Since boot
programs must be available at all times, the only useful boot block is
at $E000–$FFFF location. All paged boot blocks can be used as
protected program space if desired.
0 = Enable erase and program of 8K byte boot block
1 = Disable erase and program of 8K byte boot block
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Appendix: MC68HC912DG128A Flash
For More Information On This Product,
Go to: www.freescale.com
421
Freescale Semiconductor, Inc.
Appendix: MC68HC912DG128A Flash
FEECTL — Flash EEPROM Control Register
$00F7
Bit 7
6
5
4
3
2
1
Bit 0
0
0
0
FEESWAI
HVEN
0
ERAS
PGM
0
0
0
0
0
0
0
0
RESET:
This register controls the programming and erasure of the Flash
EEPROM.
Freescale Semiconductor, Inc...
FEESWAI — Flash EEPROM Stop in Wait Control
0 = Do not halt Flash EEPROM clock when the part is in wait
mode.
1 = Halt Flash EEPROM clock when the part is in wait mode.
HVEN — High-Voltage Enable
This bit enables the charge pump to supply high voltages for program
and erase operations in the array. HVEN can only be set if either PGM
or ERAS are set and the proper sequence for program or erase is
followed.
0 = Disables high voltage to array and charge pump off
1 = Enables high voltage to array and charge pump on
ERAS — Erase Control
This bit configures the memory for erase operation. ERAS is
interlocked with the PGM bit such that both bits cannot be equal to 1
or set to1 at the same time.
0 = Erase operation is not selected.
1 = Erase operation selected.
PGM — Program Control
This bit configures the memory for program operation. PGM is
interlocked with the ERAS bit such that both bits cannot be equal to 1
or set to1 at the same time.
0 = Program operation is not selected.
1 = Program operation selected.
Technical Data
422
MC68HC912DG128 — Rev 3.0
Appendix: MC68HC912DG128A Flash
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Appendix: MC68HC912DG128A Flash
Operation
21.7 Operation
The Flash EEPROM can contain program and data. On reset, it can
operate as a bootstrap memory to provide the CPU with internal
initialization information during the reset sequence.
21.7.1 Bootstrap Operation Single-Chip Mode
After reset, the CPU controlling the system will begin booting up by
fetching the first program address from address $FFFE.
21.7.2 Normal Operation
The Flash EEPROM allows a byte or aligned word read in one bus cycle.
Misaligned word read require an additional bus cycle. The Flash
EEPROM array responds to read operations only. Write operations are
ignored.
21.7.3 Program/Erase Operation
An unprogrammed Flash EEPROM bit has a logic state of one. A bit
must be programmed to change its state from one to zero. Erasing a bit
returns it to a logic one. The Flash EEPROM has a minimum
program/erase life of 100 cycles. Programming or erasing the Flash
EEPROM is accomplished by a series of control register writes.
Programming is restricted to aligned word at a time as determined by
internal signal SZ8 and ADDR[0]. The Flash EEPROM must first be
completely erased prior to programming final data values.
Programming and erasing of Flash locations cannot be performed by
code being executed from the FLASH memory. While these operations
must be performed in the order shown, other unrelated operations may
occur between the steps. Do not exceed tFPGM maximum (40µs).
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Appendix: MC68HC912DG128A Flash
For More Information On This Product,
Go to: www.freescale.com
423
Freescale Semiconductor, Inc.
Appendix: MC68HC912DG128A Flash
21.8 Programming the Flash EEPROM
Programming the Flash EEPROM is done on a row basis. A row consists
of 64 consecutive bytes starting from addresses $XX00, $XX40, $XX80
and $XXC0. Use this step-by-step procedure to program a row of Flash
memory.
Freescale Semiconductor, Inc...
1. Set the PGM bit. This configures the memory for program
operation and enables the latching of address and data for
programming.
2. Write to any Flash address with any data within the row address
range desired.
3. Wait for a time, tNVS (min. 10µs).
4. Set the HVEN bit.
5. Wait for a time, tPGS (min. 5µs).
6. Write to the Flash address with data to the word desired to be
programmed. If BOOTP is asserted, an attempt to program an
address in the boot block will be ignored.
7. Wait for a time, tFPGM (min. 30µs).
8. Repeat steps 6 and 7 until all the words within the row are
programmed.
9. Clear the PGM bit.
10. Wait for a time, tNVH (min. 5µs).
11. Clear the HVEN bit.
12. After time, tRCV (min 1µs), the memory can be accessed in read
mode again.
This program sequence is repeated throughout the memory until all data
is programmed. For minimum overall programming time and least
program disturb effect, the sequence should be part of an intelligent
operation which iterates per row.
Technical Data
424
MC68HC912DG128 — Rev 3.0
Appendix: MC68HC912DG128A Flash
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Appendix: MC68HC912DG128A Flash
Erasing the Flash EEPROM
21.9 Erasing the Flash EEPROM
The following sequence demonstrates the recommended procedure for
erasing any of the Flash EEPROM array.
1. Set the ERAS bit.
2. Write to any valid address in the Flash array. The data written and
the address written are not important. The boot block will be
erased only if the control bit BOOTP is negated.
3. Wait for a time, tNVS (min. 10µs).
4. Set the HVEN bit.
5. Wait for a time, tERAS (min. 8ms).
6. Clear the ERAS bit.
7. Wait for a time, tNVHL (min. 100µs).
8. Clear the HVEN bit.
9. After time, tRCV (min 1µs), the memory can be accessed in read
mode again.
21.10 Stop or Wait Mode
When stop or wait commands are executed, the MCU puts the Flash
EEPROM in stop or wait mode. In these modes the Flash module will
cease erasure or programming immediately.
CAUTION:
It is advised not to enter stop or wait modes when program or erase
operation of the Flash array is in progress.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Appendix: MC68HC912DG128A Flash
For More Information On This Product,
Go to: www.freescale.com
425
Freescale Semiconductor, Inc.
Freescale Semiconductor, Inc...
Appendix: MC68HC912DG128A Flash
Technical Data
426
MC68HC912DG128 — Rev 3.0
Appendix: MC68HC912DG128A Flash
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Section 22. Appendix: MC68HC912DG128A EEPROM
22.1 Contents
22.2
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 427
22.3
EEPROM Programmer’s Model . . . . . . . . . . . . . . . . . . . . . . . 428
22.4
EEPROM Control Registers . . . . . . . . . . . . . . . . . . . . . . . . . . 430
22.5
Program/Erase Operation. . . . . . . . . . . . . . . . . . . . . . . . . . . . 436
22.6
Shadow Word Mapping . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 436
22.7
Programming EEDIVH and EEDIVL Registers. . . . . . . . . . . . 437
22.2 Introduction
The 68HC912DG128A EEPROM nonvolatile memory is arranged in a
16-bit configuration. The EEPROM array may be read as either bytes,
aligned words or misaligned words. Access times are one bus cycle for
byte and aligned word access and two bus cycles for misaligned word
operations.
Programming is by byte or aligned word. Attempts to program or erase
misaligned words will fail. Only the lower byte will be latched and
programmed or erased. Programming and erasing of the user EEPROM
can be done in normal modes.
Each EEPROM byte or aligned word must be erased before
programming. The EEPROM module supports byte, aligned word, row
(32 bytes) or bulk erase, all using the internal charge pump. The erased
state is $FF. The EEPROM module has hardware interlocks which
protect stored data from corruption by accidentally enabling the
program/erase voltage. Programming voltage is derived from the
internal VDD supply with an internal charge pump.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Appendix: MC68HC912DG128A EEPROM
For More Information On This Product,
Go to: www.freescale.com
427
Freescale Semiconductor, Inc.
Appendix: MC68HC912DG128A EEPROM
22.3 EEPROM Programmer’s Model
The EEPROM module consists of two separately addressable sections.
The first is an eight-byte memory mapped control register block used for
control, testing and configuration of the EEPROM array. The second
section is the EEPROM array itself.
Freescale Semiconductor, Inc...
At reset, the eight-byte register section starts at address $00EC and the
EEPROM array is located from addresses $0800 to $0FFF. Registers
$00EC-$00ED are reserved.
Read/write access to the memory array section can be enabled or
disabled by the EEON control bit in the INITEE register ($0012). This
feature allows the access of memory mapped resources that have lower
priority than the EEPROM memory array. EEPROM control registers can
be accessed regardless of the state of EEON. For information on remapping the register block and EEPROM address space, refer to
Operating Modes.
CAUTION:
It is strongly recommended to discontinue program/erase operations
during WAIT (when EESWAI=1) or STOP modes since all
program/erase activities will be terminated abruptly and considered
unsuccessful.
For lowest power consumption during WAIT mode, it is advised to turn
off EEPGM.
The EEPROM module contains an extra word called SHADOW word
which is loaded at reset into the EEMCR, EEDIVH and EEDIVL
registers. To program the SHADOW word, when in special modes
(SMODN=0), the NOSHW bit in EEMCR register must be cleared.
Normal programming routines are used to program the SHADOW word
which becomes accessible at address $0FC0–$0FC1 when NOSHW is
cleared. At the next reset the SHADOW word data is loaded into the
EEMCR, EEDIVH and EEDIVL registers. The SHADOW word can be
protected from being programmed or erased by setting the SHPROT bit
of EEPROT register.
Technical Data
428
MC68HC912DG128 — Rev 3.0
Appendix: MC68HC912DG128A EEPROM
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Appendix: MC68HC912DG128A EEPROM
EEPROM Programmer’s Model
A steady internal self-time clock is required to provide accurate counts
to meet EEPROM program/erase requirements. This clock is generated
via by a programmable 10-bit prescaler register. Automatic
program/erase termination is also provided.
Freescale Semiconductor, Inc...
In ordinary situations, with crystal operating properly, the steady internal
self-time clock is derived from the input clock source (EXTALi). The
divider value is as in EEDIVH:EEDIVL. In limp-home mode, where the
oscillator has malfunctioned or is unavailable, the self-time clock is
derived from the PLL with approximately 1 MHz frequency, with a
predefined divider value of $0023. Program/erase operation is not
guaranteed in limp-home mode. The clock switching function is only
applicable for permanent loss of crystal condition, so the program/erase
will also not be guaranteed when the loss of crystal condition is
intermittent.
It is strongly recommended that the clock monitor is enabled to ensure
that the program/erase operation will be shutdown in the event of loss of
crystal with a clock monitor reset, or switch to a limp-home mode clock.
This will prevent unnecessary stress on the emulated EEPROM during
oscillator failure.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Appendix: MC68HC912DG128A EEPROM
For More Information On This Product,
Go to: www.freescale.com
429
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Appendix: MC68HC912DG128A EEPROM
22.4 EEPROM Control Registers
EEDIVH — EEPROM Modulus Divider
RESET:
Bit 7
0
0
6
0
0
$00EE
5
0
0
4
0
0
3
0
0
2
0
0
1
EEDIV9
—(1)
Bit 0
EEDIV8
—(1)
1. Loaded from SHADOW word.
EEDIVL — EEPROM Modulus Divider
RESET:
Bit 7
EEDIV7
—(1)
6
EEDIV6
—(1)
5
EEDIV5
—(1)
$00EF
4
EEDIV4
—(1)
3
EEDIV3
—(1)
2
EEDIV2
—(1)
1
EEDIV1
—(1)
Bit 0
EEDIV0
—(1)
1. Loaded from SHADOW word.
EEDIV[9:0] — Prescaler divider
Loaded from SHADOW word at reset.
Read anytime. Write once in normal modes (SMODN =1) if EELAT =
0 and anytime in special modes (SMODN =0) if EELAT = 0.
The prescaler divider is required to produce a self-time clock with a
fixed frequency around 28.6 Khz for the range of oscillator
frequencies. The divider is set so that the oscillator frequency can be
divided by a divide factor that can produce a 35 µs +/- 2µs pulse.
CAUTION:
An incorrect or uninitialized value on EEDIV can result in overstress of
EEPROM array during program/erase operation. It is also strongly
recommend not to program EEPROM with oscillator frequencies less
than 250 Khz.
The EEDIV value is determined by the following formula:
–6
EEDIV = INT [ EXTALi (hz) x 35 ×10 + 0.5 ]
NOTE:
INT[A] denotes the round down integer value of A. Program/erase cycles
will not be activated when EEDIV = 0.
Technical Data
430
MC68HC912DG128 — Rev 3.0
Appendix: MC68HC912DG128A EEPROM
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Appendix: MC68HC912DG128A EEPROM
EEPROM Control Registers
Table 22-1. EEDIV Selection
Osc Freq.
16 Mhz
8 Mhz
4 Mhz
2 Mhz
1 Mhz
500 Khz
250 Khz
Osc Period
62.5ns
125ns
250ns
500ns
1 µs
2 µs
4 µs
Divide Factor
560
280
140
70
35
18
9
EEDIV
$0230
$0118
$008C
$0046
$0023
$0012
$0009
EEMCR — EEPROM Module Configuration
Bit 7
6
5
NOBDML
NOSHW
—(2)
—(2)
RESET:
$00F0
4
3
2
1
Bit 0
(1)
1
EESWAI
PROTLCK
DMY
1
1
0
0
RESERVED
—(2)
—(2)
1. Bits 4 and 5 have test functions and should not be programmed.
2. Loaded from SHADOW word.
Bits[7:4] are loaded at reset from the EEPROM SHADOW word.
NOTE:
The bits 5 and 4 are reserved for test purposes. These locations in
SHADOW word should not be programmed otherwise some locations of
regular EEPROM array will not be more visible.
NOBDML — Background Debug Mode Lockout Disable
0 = The BDM lockout is enabled.
1 = The BDM lockout is disabled.
Loaded from SHADOW word at reset.
Read anytime. Write anytime in special modes (SMODN=0).
NOSHW — SHADOW Word Disable
0 = The SHADOW word is enabled and accessible at address
$0FC0-$0FC1.
1 = Regular EEPROM array at address $0FC0-$0FC1.
Loaded from SHADOW word at reset.
Read anytime. Write anytime in special modes (SMODN=0).
When NOSHW cleared, the regular EEPROM array bytes at address
$0FC0 and $0FC1 are not visible. The SHADOW word is accessed
instead for both read and program/erase operations. Bits[7:4] from
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Appendix: MC68HC912DG128A EEPROM
For More Information On This Product,
Go to: www.freescale.com
431
Freescale Semiconductor, Inc.
Appendix: MC68HC912DG128A EEPROM
the high byte of the SHADOW word, $0FC0, are loaded to
EEMCR[7:4]. Bits[1:0] from the high byte of the SHADOW word,
$0FC0,are loaded to EEDIVH[1:0]. Bits[7:0] from the low byte of the
SHADOW word, $0FC1,are loaded to EEDIVL[7:0]. BULK
program/erase only applies if SHADOW word is enabled.
NOTE:
Bit 6 from high byte of SHADOW word should not be programmed in
order to have the full EEPROM array visible.
Freescale Semiconductor, Inc...
EESWAI — EEPROM Stops in Wait Mode
0 = The module is not affected during WAIT mode
1 = The module ceases to be clocked during WAIT mode
Read and write anytime.
NOTE:
The EESWAI bit should be cleared if the WAIT mode vectors are
mapped in the EEPROM array.
PROTLCK — Block Protect Write Lock
0 = Block protect bits and bulk erase protection bit can be written
1 = Block protect bits are locked
Read anytime. Write once in normal modes (SMODN = 1), set and
clear any time in special modes (SMODN = 0).
DMY— Dummy bit
Read and write anytime.
Technical Data
432
MC68HC912DG128 — Rev 3.0
Appendix: MC68HC912DG128A EEPROM
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Appendix: MC68HC912DG128A EEPROM
EEPROM Control Registers
EEPROT — EEPROM Block Protect
RESET:
Bit 7
SHPROT
1
6
1
1
$00F1
5
BPROT5
1
4
BPROT4
1
3
BPROT3
1
2
BPROT2
1
1
BPROT1
1
Bit 0
BPROT0
1
Prevents accidental writes to EEPROM. Read anytime. Write anytime if
EEPGM = 0 and PROTLCK = 0.
SHPROT — SHADOW Word Protection
0 = The SHADOW word can be programmed and erased.
1 = The SHADOW word is protected from being programmed and
erased.
BPROT[5:0] — EEPROM Block Protection
0 = Associated EEPROM block can be programmed and erased.
1 = Associated EEPROM block is protected from being
programmed and erased.
Table 22-2. 2K byte EEPROM Block Protection
Bit Name
BPROT5
BPROT4
BPROT3
BPROT2
BPROT1
BPROT0
Block Protected
$0800 to $0BFF
$0C00 to $0DFF
$0E00 to $0EFF
$0F00 to $0F7F
$0F80 to $0FBF
$0FC0 to $0FFF
Block Size
1024 Bytes
512 Bytes
256 Bytes
128 Bytes
64 Bytes
64 Bytes
EETST — EEPROM Test
RESET:
Bit 7
0
0
$00F2
6
EREVTN
0
5
0
0
4
0
0
3
0
0
2
ETMSD
0
1
ETMR
0
Bit 0
ETMSE
0
In normal mode, writes to EETST control bits have no effect and
always read zero. The EEPROM module cannot be placed in test
mode inadvertently during normal operation
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Appendix: MC68HC912DG128A EEPROM
For More Information On This Product,
Go to: www.freescale.com
433
Freescale Semiconductor, Inc.
Appendix: MC68HC912DG128A EEPROM
.
EEPROG — EEPROM Control
RESET:
Bit 7
BULKP
1
6
0
0
$00F3
5
AUTO
0
4
BYTE
0
3
ROW
0
2
ERASE
0
1
EELAT
0
Bit 0
EEPGM
0
BULKP — Bulk Erase Protection
0 = EEPROM can be bulk erased.
1 = EEPROM is protected from being bulk or row erased.
Freescale Semiconductor, Inc...
Read anytime. Write anytime if EEPGM = 0 and PROTLCK = 0.
AUTO — Automatic shutdown of program/erase operation.
EEPGM is cleared automatically after the program/erase cycles are
finished when AUTO is set.
0 = Automatic clear of EEPGM is disabled.
1 = Automatic clear of EEPGM is enabled.
Read anytime. Write anytime if EEPGM = 0.
BYTE — Byte and Aligned Word Erase
0 = Bulk or row erase is enabled.
1 = One byte or one aligned word erase only.
Read anytime. Write anytime if EEPGM = 0.
ROW — Row or Bulk Erase (when BYTE = 0)
0 = Erase entire EEPROM array.
1 = Erase only one 32-byte row.
Read anytime. Write anytime if EEPGM = 0.
BYTE and ROW have no effect when ERASE = 0
Table 22-3. Erase Selection
BYTE
0
0
1
1
ROW
0
1
0
1
Block size
Bulk erase entire EEPROM array
Row erase 32 bytes
Byte or aligned word erase
Byte or aligned word erase
Technical Data
434
MC68HC912DG128 — Rev 3.0
Appendix: MC68HC912DG128A EEPROM
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc.
Appendix: MC68HC912DG128A EEPROM
EEPROM Control Registers
If BYTE = 1 only the location specified by the address written to the
programming latches will be erased. The operation will be a byte or
an aligned word erase depending on the size of written data.
ERASE — Erase Control
0 = EEPROM configuration for programming.
1 = EEPROM configuration for erasure.
Read anytime. Write anytime if EEPGM = 0.
Configures the EEPROM for erasure or programming.
Freescale Semiconductor, Inc...
Unless BULKP is set, erasure is by byte, aligned word, row or bulk.
EELAT — EEPROM Latch Control
0 = EEPROM set up for normal reads.
1 = EEPROM address and data bus latches set up for
programming or erasing.
Read anytime.
Write anytime except when EEPGM = 1 or EEDIV = 0.
BYTE, ROW, ERASE and EELAT bits can be written simultaneously
or in any sequence.
EEPGM — Program and Erase Enable
0 = Disables program/erase voltage to EEPROM.
1 = Applies program/erase voltage to EEPROM.
The EEPGM bit can be set only after EELAT has been set. When
EELAT and EEPGM are set simultaneously, EEPGM remains clear
but EELAT is set.
The BULKP, AUTO, BYTE, ROW, ERASE and EELAT bits cannot be
changed when EEPGM is set. To complete a program or erase cycle
when AUTO bit is clear, two successive writes to clear EEPGM and
EELAT bits are required before reading the programmed data. When
AUTO bit is set, EEPGM is automatically cleared after the program or
erase cycle is over. A write to an EEPROM location has no effect
when EEPGM is set. Latched address and data cannot be modified
during program or erase.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Appendix: MC68HC912DG128A EEPROM
For More Information On This Product,
Go to: www.freescale.com
435
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Appendix: MC68HC912DG128A EEPROM
22.5 Program/Erase Operation
A program or erase operation should follow the sequence below if AUTO
bit is clear:
1. Write BYTE, ROW and ERASE to desired value, write EELAT = 1
2. Write a byte or an aligned word to an EEPROM address
3. Write EEPGM = 1
4. Wait for programming, tPROG or erase, tERASE delay time (10ms)
5. Write EEPGM = 0
6. Write EELAT = 0
If AUTO bit is set, steps 4 and 5 can be replaced by a step to poll the
EEPGM bit until is cleared.
It is possible to program/erase more bytes or words without intermediate
EEPROM reads, by jumping from step 5 to step 2.
22.6 Shadow Word Mapping
The shadow word is mapped to location $_FC0 and $_FC1 when the
NOSHW bit in EEMCR register is zero. The value in the shadow word is
loaded to the EEMCR, EEDIVH and EEDIVL after reset. Table 22-4
shows the mapping of each bit from shadow word to the registers
Table 22-4. Shadow word mapping
Shadow word location
Register / Bit
$_FC0 bit 7
EEMCR / NOBDML
$_FC0, bit 6
EEMCR / NOSHW
$_FC0, bit 5
EEMCR / bit 5(1)
$_FC0, bit 4
EEMCR / bit 4(1)
$_FC0, bit 3:2
not mapped(2))
$_FC0, bit 1:0
EEDIVH / bit 1:0
$_FC1, bit 7:0
EEMCR / bit 7:0
1. Reserved for testing. Must be set to one in user application.
2. Reserved. Must be set to one in user application for future compatibility.
Technical Data
436
MC68HC912DG128 — Rev 3.0
Appendix: MC68HC912DG128A EEPROM
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Appendix: MC68HC912DG128A EEPROM
Programming EEDIVH and EEDIVL Registers
22.7 Programming EEDIVH and EEDIVL Registers
The EEDIVH and EEDIVL registers must be correctly set according to
the oscillator frequency before any EEPROM location can be
programmed or erased.
22.7.1 Normal mode
The EEDIVH and EEDIVL registers are write once in normal mode.
Upon system reset, the application program is required to write correct
divider value to EEDIVH and EEDIVL registers based on the oscillator
frequency. After the first write, the value in the EEDIVH and EEDIVL
registers is locked from been overwritten until the next reset. The
EEPROM is then ready for standard program/erase routines.
CAUTION:
Runaway code can possibly corrupt the EEDIVH and EEDIVL registers
if they are not initialized for the write once.
22.7.2 Special mode
If an existing application code with EEPROM program/erase routines is
fixed and the system is already operating at a known oscillator
frequency, it is recommended to initialize the shadow word with the
corresponding EEDIVH and EEDIVL values in special mode. The
shadow word initializes EEDIVH and EEDIVL registers upon system
reset to ensure software compatibility with existing code. Initializing the
EEDIVH and EEDIVL registers in special modes (SMODN=0) is
accomplished by the following steps.
1. Write correct divider value to EEDIVH and EEDIVL registers
based on the oscillator frequency as per Table 22-1.
2. Remove the SHADOW word protection by clearing SHPROT bit in
EEPROT register.
3. Clear NOSHW bit in EEMCR register to make the SHADOW word
visible at $0FC0-$0FC1.
4. Write NOSHW bit in EEMCR register to make the SHADOW word
visible at $0FC0-$0FC1.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Appendix: MC68HC912DG128A EEPROM
For More Information On This Product,
Go to: www.freescale.com
437
Freescale Semiconductor, Inc.
Appendix: MC68HC912DG128A EEPROM
5. Program bits 1 and 0 of the high byte of the SHADOW word and
bits 7 to 0 of the low byte of the SHADOW word like a regular
EEPROM location at address $0FC0 and $0FC1. Do not program
other bits of the high byte of the SHADOW word (location $0FC0);
otherwise some regular EEPROM array locations will not be
visible. At the next reset, the SHADOW values are loaded into the
EEDIVH and EEDIVL registers. They do not require further
initialization as long as the oscillator frequency of the target
application is not changed.
Freescale Semiconductor, Inc...
6. Protect the SHADOW word by setting SHPROT bit in EEPROT
register.
Technical Data
438
MC68HC912DG128 — Rev 3.0
Appendix: MC68HC912DG128A EEPROM
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Section 23. Revision History
This section lists the revision history of the document since the first
release. Data for previous versions and internal drafts is unavailable.
Changes from Rev 2.0 to Rev 3.0
Section
Page (in Rev 3.0)
Pinout and Signal
Descriptions
Clock Functions
Description of change
41
Ca in Figure 3-3 changed to Cp
43
Note added about consideration of crystal selection due to EMC
emissions
157
Note added about consideration of crystal selection due to EMC
emissions
161
Major rewrite of Limp-Home and Fast STOP Recovery modes.
179
System Clock Frequency formulas updated for clarification.
180
Figure 11-6 modified for clarification.
183
Figure 11-9 modified for clarification.
326
First two bullets of sleep mode description updated
339
SLPRQ = 1 description updated
392
Changes to maximum EEPROM erase and data retention times
395
fXTAL removed
395
Footnote added restricting external oscillator operating frequency
to 8MHz when using a quartz crystal
406
Table footnote removed from Table 19-16 regarding VDDPLL
MSCAN Controller
Electrical
Specifications
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Revision History
For More Information On This Product,
Go to: www.freescale.com
439
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Revision History
Section
Appendix: CGM
Practical Aspects
Page (in Rev 3.0)
Description of change
408
Added section on DC bias
409
Point 3 removed regarding high frequency resonators
412
In paragraph 2, C changed to C0, R changed to R0
413
In Table 20-1
In header, C changed to C0, R changed to R0
Extra column added for Cp
413
In Table 20-2
In header, C changed to C0, R changed to R0
Extra column added for Cp
417
Extra bullets added
Changes from Rev 1.0 to Rev 2.0
Section
Page (in Rev 2.0)
Description of change
Clock Functions
157
Prescaled MCLK and TIMCLK signal names added to Figure 21
for clarification
ECT
188
Prescaled clock from timer changed to Prescaled MCLK in Figure
29 for clarification
MSI
244
SP0DR register state on reset clarified
Technical Data
440
MC68HC912DG128 — Rev 3.0
Revision History
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Technical Data — MC68HC912DG128
Glossary
A — See “accumulators (A and B or D).”
accumulators (A and B or D) — Two 8-bit (A and B) or one 16-bit (D) general-purpose registers
in the CPU. The CPU uses the accumulators to hold operands and results of arithmetic
and logic operations.
acquisition mode — A mode of PLL operation with large loop bandwidth. Also see ’tracking
mode’.
address bus — The set of wires that the CPU or DMA uses to read and write memory locations.
addressing mode — The way that the CPU determines the operand address for an instruction.
The M68HC12 CPU has 15 addressing modes.
ALU — See “arithmetic logic unit (ALU).”
analogue-to-digital converter (ATD) — The ATD module is an 8-channel, multiplexed-input
successive-approximation analog-to-digital converter.
arithmetic logic unit (ALU) — The portion of the CPU that contains the logic circuitry to perform
arithmetic, logic, and manipulation operations on operands.
asynchronous — Refers to logic circuits and operations that are not synchronized by a common
reference signal.
ATD — See “analogue-to-digital converter”.
B — See “accumulators (A and B or D).”
baud rate — The total number of bits transmitted per unit of time.
BCD — See “binary-coded decimal (BCD).”
binary — Relating to the base 2 number system.
binary number system — The base 2 number system, having two digits, 0 and 1. Binary
arithmetic is convenient in digital circuit design because digital circuits have two
permissible voltage levels, low and high. The binary digits 0 and 1 can be interpreted to
correspond to the two digital voltage levels.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Glossary
For More Information On This Product,
Go to: www.freescale.com
441
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Glossary
binary-coded decimal (BCD) — A notation that uses 4-bit binary numbers to represent the 10
decimal digits and that retains the same positional structure of a decimal number. For
example,
234 (decimal) = 0010 0011 0100 (BCD)
bit — A binary digit. A bit has a value of either logic 0 or logic 1.
branch instruction — An instruction that causes the CPU to continue processing at a memory
location other than the next sequential address.
break module — The break module allows software to halt program execution at a
programmable point in order to enter a background routine.
breakpoint — A number written into the break address registers of the break module. When a
number appears on the internal address bus that is the same as the number in the break
address registers, the CPU executes the software interrupt instruction (SWI).
break interrupt — A software interrupt caused by the appearance on the internal address bus
of the same value that is written in the break address registers.
bus — A set of wires that transfers logic signals.
bus clock — See "CPU clock".
byte — A set of eight bits.
CAN — See "Motorola scalable CAN."
CCR — See “condition code register.”
central processor unit (CPU) — The primary functioning unit of any computer system. The
CPU controls the execution of instructions.
CGM — See “clock generator module (CGM).”
clear — To change a bit from logic 1 to logic 0; the opposite of set.
clock — A square wave signal used to synchronize events in a computer.
clock generator module (CGM) — The CGM module generates a base clock signal from which
the system clocks are derived. The CGM may include a crystal oscillator circuit and/or
phase-locked loop (PLL) circuit.
comparator — A device that compares the magnitude of two inputs. A digital comparator defines
the equality or relative differences between two binary numbers.
Technical Data
442
MC68HC912DG128 — Rev 3.0
Glossary
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Glossary
computer operating properly module (COP) — A counter module that resets the MCU if
allowed to overflow.
condition code register (CCR) — An 8-bit register in the CPU that contains the interrupt mask
bit and five bits that indicate the results of the instruction just executed.
control bit — One bit of a register manipulated by software to control the operation of the
module.
control unit — One of two major units of the CPU. The control unit contains logic functions that
synchronize the machine and direct various operations. The control unit decodes
instructions and generates the internal control signals that perform the requested
operations. The outputs of the control unit drive the execution unit, which contains the
arithmetic logic unit (ALU), CPU registers, and bus interface.
COP — See "computer operating properly module (COP)."
CPU — See “central processor unit (CPU).”
CPU12 — The CPU of the MC68HC12 Family.
CPU clock — Bus clock select bits BCSP and BCSS in the clock select register (CLKSEL)
determine which clock drives SYSCLK for the main system, including the CPU and buses.
When EXTALi drives the SYSCLK, the CPU or bus clock frequency (fo) is equal to the
EXTALi frequency divided by 2.
CPU cycles — A CPU cycle is one period of the internal bus clock, normally derived by dividing
a crystal oscillator source by two or more so the high and low times will be equal. The
length of time required to execute an instruction is measured in CPU clock cycles.
CPU registers — Memory locations that are wired directly into the CPU logic instead of being
part of the addressable memory map. The CPU always has direct access to the
information in these registers. The CPU registers in an M68HC12 are:
•
A (8-bit accumulator)
•
B (8-bit accumulator)
–
D (16-bit accumulator formed by concatenation of accumulators A and B)
•
IX (16-bit index register)
•
IY (16-bit index register)
•
SP (16-bit stack pointer)
•
PC (16-bit program counter)
•
CCR (8-bit condition code register)
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Glossary
For More Information On This Product,
Go to: www.freescale.com
443
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Glossary
cycle time — The period of the operating frequency: tCYC = 1/fOP.
D — See “accumulators (A and B or D).”
decimal number system — Base 10 numbering system that uses the digits zero through nine.
duty cycle — A ratio of the amount of time the signal is on versus the time it is off. Duty cycle is
usually represented by a percentage.
ECT — See “enhanced capture timer.”
EEPROM — Electrically erasable, programmable, read-only memory. A nonvolatile type of
memory that can be electrically erased and reprogrammed.
EPROM — Erasable, programmable, read-only memory. A nonvolatile type of memory that can
be erased by exposure to an ultraviolet light source and then reprogrammed.
enhanced capture timer (ECT) — The HC12 Enhanced Capture Timer module has the features
of the HC12 Standard Timer module enhanced by additional features in order to enlarge
the field of applications.
exception — An event such as an interrupt or a reset that stops the sequential execution of the
instructions in the main program.
fetch — To copy data from a memory location into the accumulator.
firmware — Instructions and data programmed into nonvolatile memory.
free-running counter — A device that counts from zero to a predetermined number, then rolls
over to zero and begins counting again.
full-duplex transmission — Communication on a channel in which data can be sent and
received simultaneously.
hexadecimal — Base 16 numbering system that uses the digits 0 through 9 and the letters A
through F.
high byte — The most significant eight bits of a word.
illegal address — An address not within the memory map
illegal opcode — A nonexistent opcode.
index registers (IX and IY) — Two 16-bit registers in the CPU. In the indexed addressing
modes, the CPU uses the contents of IX or IY to determine the effective address of the
operand. IX and IY can also serve as a temporary data storage locations.
Technical Data
444
MC68HC912DG128 — Rev 3.0
Glossary
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Glossary
input/output (I/O) — Input/output interfaces between a computer system and the external world.
A CPU reads an input to sense the level of an external signal and writes to an output to
change the level on an external signal.
instructions — Operations that a CPU can perform. Instructions are expressed by programmers
as assembly language mnemonics. A CPU interprets an opcode and its associated
operand(s) and instruction.
inter-IC bus (I2C) — A two-wire, bidirectional serial bus that provides a simple, efficient method
of data exchange between devices.
interrupt — A temporary break in the sequential execution of a program to respond to signals
from peripheral devices by executing a subroutine.
interrupt request — A signal from a peripheral to the CPU intended to cause the CPU to
execute a subroutine.
I/O — See “input/output (I/0).”
jitter — Short-term signal instability.
latch — A circuit that retains the voltage level (logic 1 or logic 0) written to it for as long as power
is applied to the circuit.
latency — The time lag between instruction completion and data movement.
least significant bit (LSB) — The rightmost digit of a binary number.
logic 1 — A voltage level approximately equal to the input power voltage (VDD).
logic 0 — A voltage level approximately equal to the ground voltage (VSS).
low byte — The least significant eight bits of a word.
M68HC12 — A Motorola family of 16-bit MCUs.
mark/space — The logic 1/logic 0 convention used in formatting data in serial communication.
mask — 1. A logic circuit that forces a bit or group of bits to a desired state. 2. A photomask used
in integrated circuit fabrication to transfer an image onto silicon.
MCU — Microcontroller unit. See “microcontroller.”
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Glossary
For More Information On This Product,
Go to: www.freescale.com
445
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Glossary
memory location — Each M68HC12 memory location holds one byte of data and has a unique
address. To store information in a memory location, the CPU places the address of the
location on the address bus, the data information on the data bus, and asserts the write
signal. To read information from a memory location, the CPU places the address of the
location on the address bus and asserts the read signal. In response to the read signal,
the selected memory location places its data onto the data bus.
memory map — A pictorial representation of all memory locations in a computer system.
MI-Bus — See "Motorola interconnect bus".
microcontroller — Microcontroller unit (MCU). A complete computer system, including a CPU,
memory, a clock oscillator, and input/output (I/O) on a single integrated circuit.
modulo counter — A counter that can be programmed to count to any number from zero to its
maximum possible modulus.
most significant bit (MSB) — The leftmost digit of a binary number.
Motorola interconnect bus (MI-Bus) — The Motorola Interconnect Bus (MI Bus) is a serial
communications protocol which supports distributed real-time control efficiently and with
a high degree of noise immunity.
Motorola scalable CAN (msCAN) — The Motorola scalable controller area network is a serial
communications protocol that efficiently supports distributed real-time control with a very
high level of data integrity.
msCAN — See "Motorola scalable CAN".
MSI — See "multiple serial interface".
multiple serial interface — A module consisting of multiple independent serial I/O sub-systems,
e.g. two SCI and one SPI.
multiplexer — A device that can select one of a number of inputs and pass the logic level of that
input on to the output.
nibble — A set of four bits (half of a byte).
object code — The output from an assembler or compiler that is itself executable machine code,
or is suitable for processing to produce executable machine code.
opcode — A binary code that instructs the CPU to perform an operation.
open-drain — An output that has no pullup transistor. An external pullup device can be
connected to the power supply to provide the logic 1 output voltage.
Technical Data
446
MC68HC912DG128 — Rev 3.0
Glossary
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Glossary
operand — Data on which an operation is performed. Usually a statement consists of an
operator and an operand. For example, the operator may be an add instruction, and the
operand may be the quantity to be added.
oscillator — A circuit that produces a constant frequency square wave that is used by the
computer as a timing and sequencing reference.
OTPROM — One-time programmable read-only memory. A nonvolatile type of memory that
cannot be reprogrammed.
overflow — A quantity that is too large to be contained in one byte or one word.
page zero — The first 256 bytes of memory (addresses $0000–$00FF).
parity — An error-checking scheme that counts the number of logic 1s in each byte transmitted.
In a system that uses odd parity, every byte is expected to have an odd number of logic
1s. In an even parity system, every byte should have an even number of logic 1s. In the
transmitter, a parity generator appends an extra bit to each byte to make the number of
logic 1s odd for odd parity or even for even parity. A parity checker in the receiver counts
the number of logic 1s in each byte. The parity checker generates an error signal if it finds
a byte with an incorrect number of logic 1s.
PC — See “program counter (PC).”
peripheral — A circuit not under direct CPU control.
phase-locked loop (PLL) — A clock generator circuit in which a voltage controlled oscillator
produces an oscillation which is synchronized to a reference signal.
PLL — See "phase-locked loop (PLL)."
pointer — Pointer register. An index register is sometimes called a pointer register because its
contents are used in the calculation of the address of an operand, and therefore points to
the operand.
polarity — The two opposite logic levels, logic 1 and logic 0, which correspond to two different
voltage levels, VDD and VSS.
polling — Periodically reading a status bit to monitor the condition of a peripheral device.
port — A set of wires for communicating with off-chip devices.
prescaler — A circuit that generates an output signal related to the input signal by a fractional
scale factor such as 1/2, 1/8, 1/10 etc.
program — A set of computer instructions that cause a computer to perform a desired operation
or operations.
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Glossary
For More Information On This Product,
Go to: www.freescale.com
447
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Glossary
program counter (PC) — A 16-bit register in the CPU. The PC register holds the address of the
next instruction or operand that the CPU will use.
pull — An instruction that copies into the accumulator the contents of a stack RAM location. The
stack RAM address is in the stack pointer.
pullup — A transistor in the output of a logic gate that connects the output to the logic 1 voltage
of the power supply.
pulse-width — The amount of time a signal is on as opposed to being in its off state.
pulse-width modulation (PWM) — Controlled variation (modulation) of the pulse width of a
signal with a constant frequency.
push — An instruction that copies the contents of the accumulator to the stack RAM. The stack
RAM address is in the stack pointer.
PWM period — The time required for one complete cycle of a PWM waveform.
RAM — Random access memory. All RAM locations can be read or written by the CPU. The
contents of a RAM memory location remain valid until the CPU writes a different value or
until power is turned off.
RC circuit — A circuit consisting of capacitors and resistors having a defined time constant.
read — To copy the contents of a memory location to the accumulator.
register — A circuit that stores a group of bits.
reserved memory location — A memory location that is used only in special factory test modes.
Writing to a reserved location has no effect. Reading a reserved location returns an
unpredictable value.
reset — To force a device to a known condition.
SCI — See "serial communication interface module (SCI)."
serial — Pertaining to sequential transmission over a single line.
serial communications interface module (SCI) — A module that supports asynchronous
communication.
serial peripheral interface module (SPI) — A module that supports synchronous
communication.
set — To change a bit from logic 0 to logic 1; opposite of clear.
Technical Data
448
MC68HC912DG128 — Rev 3.0
Glossary
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Glossary
shift register — A chain of circuits that can retain the logic levels (logic 1 or logic 0) written to
them and that can shift the logic levels to the right or left through adjacent circuits in the
chain.
signed — A binary number notation that accommodates both positive and negative numbers.
The most significant bit is used to indicate whether the number is positive or negative,
normally logic 0 for positive and logic 1 for negative. The other seven bits indicate the
magnitude of the number.
software — Instructions and data that control the operation of a microcontroller.
software interrupt (SWI) — An instruction that causes an interrupt and its associated vector
fetch.
SPI — See "serial peripheral interface module (SPI)."
stack — A portion of RAM reserved for storage of CPU register contents and subroutine return
addresses.
stack pointer (SP) — A 16-bit register in the CPU containing the address of the next available
storage location on the stack.
start bit — A bit that signals the beginning of an asynchronous serial transmission.
status bit — A register bit that indicates the condition of a device.
stop bit — A bit that signals the end of an asynchronous serial transmission.
subroutine — A sequence of instructions to be used more than once in the course of a program.
The last instruction in a subroutine is a return from subroutine (RTS) instruction. At each
place in the main program where the subroutine instructions are needed, a jump or branch
to subroutine (JSR or BSR) instruction is used to call the subroutine. The CPU leaves the
flow of the main program to execute the instructions in the subroutine. When the RTS
instruction is executed, the CPU returns to the main program where it left off.
synchronous — Refers to logic circuits and operations that are synchronized by a common
reference signal.
timer — A module used to relate events in a system to a point in time.
toggle — To change the state of an output from a logic 0 to a logic 1 or from a logic 1 to a logic 0.
tracking mode — A mode of PLL operation with narrow loop bandwidth. Also see ‘acquisition
mode.’
MC68HC912DG128 — Rev 3.0
MOTOROLA
Technical Data
Glossary
For More Information On This Product,
Go to: www.freescale.com
449
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
Glossary
two’s complement — A means of performing binary subtraction using addition techniques. The
most significant bit of a two’s complement number indicates the sign of the number (1
indicates negative). The two’s complement negative of a number is obtained by inverting
each bit in the number and then adding 1 to the result.
unbuffered — Utilizes only one register for data; new data overwrites current data.
unimplemented memory location — A memory location that is not used. Writing to an
unimplemented location has no effect. Reading an unimplemented location returns an
unpredictable value.
variable — A value that changes during the course of program execution.
VCO — See "voltage-controlled oscillator."
vector — A memory location that contains the address of the beginning of a subroutine written
to service an interrupt or reset.
voltage-controlled oscillator (VCO) — A circuit that produces an oscillating output signal of a
frequency that is controlled by a dc voltage applied to a control input.
waveform — A graphical representation in which the amplitude of a wave is plotted against time.
wired-OR — Connection of circuit outputs so that if any output is high, the connection point is
high.
word — A set of two bytes (16 bits).
write — The transfer of a byte of data from the CPU to a memory location.
.
Technical Data
450
MC68HC912DG128 — Rev 3.0
Glossary
For More Information On This Product,
Go to: www.freescale.com
MOTOROLA
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
For More Information On This Product,
Go to: www.freescale.com
Freescale Semiconductor, Inc...
Freescale Semiconductor, Inc.
HOW TO REACH US:
USA/EUROPE/LOCATIONS NOT LISTED:
Motorola Literature Distribution;
P.O. Box 5405, Denver, Colorado 80217
1-303-675-2140 or 1-800-441-2447
JAPAN:
Motorola Japan Ltd.; SPS, Technical Information Center,
3-20-1, Minami-Azabu Minato-ku, Tokyo 106-8573 Japan
81-3-3440-3569
ASIA/PACIFIC:
Motorola Semiconductors H.K. Ltd.;
Silicon Harbour Centre, 2 Dai King Street,
Tai Po Industrial Estate, Tai Po, N.T., Hong Kong
852-26668334
TECHNICAL INFORMATION CENTER:
1-800-521-6274
Information in this document is provided solely to enable system and software
implementers to use Motorola products. There are no express or implied copyright
licenses granted hereunder to design or fabricate any integrated circuits or
integrated circuits based on the information in this document.
Motorola reserves the right to make changes without further notice to any products
herein. Motorola makes no warranty, representation or guarantee regarding the
suitability of its products for any particular purpose, nor does Motorola assume any
HOME PAGE:
http://motorola.com/semiconductors
liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation consequential or incidental
damages. “Typical” parameters which may be provided in Motorola data sheets
and/or specifications can and do vary in different applications and actual
performance may vary over time. All operating parameters, including “Typicals”
must be validated for each customer application by customer’s technical experts.
Motorola does not convey any license under its patent rights nor the rights of
others. Motorola products are not designed, intended, or authorized for use as
components in systems intended for surgical implant into the body, or other
applications intended to support or sustain life, or for any other application in which
the failure of the Motorola product could create a situation where personal injury or
death may occur. Should Buyer purchase or use Motorola products for any such
unintended or unauthorized application, Buyer shall indemnify and hold Motorola
and its officers, employees, subsidiaries, affiliates, and distributors harmless
against all claims, costs, damages, and expenses, and reasonable attorney fees
arising out of, directly or indirectly, any claim of personal injury or death associated
with such unintended or unauthorized use, even if such claim alleges that Motorola
was negligent regarding the design or manufacture of the part.
Motorola and the Stylized M Logo are registered in the U.S. Patent and Trademark
Office. digital dna is a trademark of Motorola, Inc. All other product or service
names are the property of their respective owners. Motorola, Inc. is an Equal
Opportunity/Affirmative Action Employer.
© Motorola, Inc. 2002
MC68HC912DG128/D
For More Information On This Product,
Go to: www.freescale.com