LUXEON S1000 High Flux Density Product Introduction The LUXEON® S1000 emitters deliver uniform beam intensity and high flux density from a uniform source. This enables tight beam control at the system level using secondary optics to provide the high center beam intensity, uniform beam and crisp, single shadow required for high performance accent spotlighting applications. LUXEON S1000 delivers tight Correlated Color Temperature control to ensure consistency in system color point. In addition these parts deliver the efficacy, lifetime and reliability that all LUXEON LEDs are renowned for. This document contains the performance data needed to design and engineer LUXEON S1000 based applications. Features and Benefits Key Applications • Specified, targeted and tested hot, at real world operating temperatures: Tj = 85°C, to ensure in application performance. • High flux density from 8mm diameter source products in 2700K, 3000K, 3500K, 4000K with 80 CRI and 3000K with 90 CRI. • Uniform intensity and color across source with high efficacy for sustainable design. • Freedom from Binning delivers color consistency within either 3-step or 4-step MacAdam ellipse. • Exceed ENERGY STAR® lumen maintenance requirements. • Recognized under the Component Recognition Program of Underwriters Laboratories Inc. UL listing E327436. • Architecture • Downlights • Spotlights Table of Contents Product Nomenclature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Average Lumen Maintenance Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Environmental Compliance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Product Selection Guide for LUXEON S1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Optical Characteristics for LUXEON S1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Electrical Characteristics for LUXEON S1000 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Absolute Maximum Ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Mechanical Dimensions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5 Relative Spectral Distribution vs. Wavelength Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Light Output Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Typical Forward Current Characterisics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Typical Radiation Pattern . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9 Packaging . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 Product Binning and Labeling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11 LUXEON S1000 Color Bin Structure . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 Forward Voltage Bins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 LUXEON S Datasheet DS80 20130907 ©2013 Philips Lumileds Lighting Company. i Product Nomenclature LUXEON S1000 is tested and binned hot at Tj = 85ºC and 700 mA DC. The part number designation is explained as follows: LXSA-BCDD Where: A — designates minimum CRI (value 8 for 80,9 for 90) B — designates radiation pattern (value P for Lambertian) C — designates color (W for White) DD — designates nominal CCT (27 for 2700K, 30 for 3000K, 35 for 3500K and 40 for 4000K) Therefore 3000K 80CRI 3-step MacAdams product will be: L X S 8 - PW 3 0 Average Lumen Maintenance Characteristics Lumen maintenance for solid-state lighting devices (LEDs) is typically defined in terms of the percentage of initial light output remaining after a specified period of time. Philips Lumileds projects that LUXEON S1000 products will deliver, on average, 70% lumen maintenance (L70) at 50,000 hours of operation at a forward current of up to 700 mA. This projection is based on constant current operation with junction temperature maintained at or below 110°C. This performance is based on independent test data, Philips Lumileds historical data from tests run on similar material systems, and internal LUXEON reliability testing. Observation of design limits included in this data sheet is required in order to achieve this projected lumen maintenance. Environmental Compliance Philips Lumileds is committed to providing environmentally friendly products to the solid-state lighting market. LUXEON S1000 is compliant to the European Union directives on the restriction of hazardous substances in electronic equipment, namely the RoHS and REACH directives. Philips Lumileds will not intentionally add the following restricted material to the LUXEON S1000: lead, mercury, cadmium, hexavalent chromium, polybrominated biphenyls (PBB) or polybrominated diphenyl ethers (PBDE). LUXEON S Datasheet DS80 20130907 ©2013 Philips Lumileds Lighting Company. 2 Product Selection Guide for LUXEON S1000 Junction Temperature = 85ºC; Test Current = 700 mA Table 1. Nominal CCT Part Number Minimum CRI [1] Typical R9 Min Luminous Flux (lm) FV [1] Typ Luminous Flux (lm) FV [1] 2700K LXS8-PW27 80 1250 LXS8-PW30 80 1250 1390 3000K LXS9-PW30 90 1050 1175 3500K LXS8-PW35 80 1300 1420 4000K LXS8-PW40 80 >20 >20 >50 >20 >20 1150 3000K 1360 1450 Note for Table 1: 1. Philips Lumileds maintains a tolerance of ± 6.5% on luminous flux and ± 2 on CRI measurements. Optical Characteristics for LUXEON S1000 Junction Temperature = 85ºC; Test Current = 700 mA Table 2. Nominal CCT Color Temperature Minimum Typical Maximum Typ Total Included Angle [1] (degrees) u0.90V Typ Viewing Angle [2] (degrees) 2u 1/2 2700K 2656K 2725K 2795K 129 105 3000K 2963K 3045K 3129K 129 105 3500K 3359K 3465K 3575K 129 105 4000K 3849K 3985K 4129K 129 105 Notes for Table 2: 1. Total angle at which 90% of total luminous flux is captured. 2. Viewing angle is the off axis angle from lamp centerline where the luminous intensity is ½ of the peak value. Electrical Characteristics for LUXEON S1000 Junction Temperature = 85ºC; Test Current = 700 mA Table 3. Nominal CCT 2700K, 3000K, 3500K, 4000K Forward Voltage Vf [1] (V) Minimum Typical Maximum Typ. Temperature Coefficient of Forward Voltage [2] (mV/°C) DVf / DTJ 23.5 25.6 29 - 15 Typical Thermal Resistance Junction to Thermal Pad (°C/W) Ru J-C 1.3 Notes for Table 3: 1. Philips Lumileds maintains a tolerance of 0.5% on forward voltage measurements. 2. Measured at 25°C ≤ TJ ≤ 125°C at If = 700 mA. LUXEON S Datasheet DS80 20130907 ©2013 Philips Lumileds Lighting Company. 3 Absolute Maximum Ratings Table 4. Parameter Maximum Performance DC Forward Current 900 mA Peak Pulsed Forward Current 900 mA ESD Sensitivity < 8000V Human Body Model (HBM) Class 3A JESD22-A114-E < 400V Machine Model (MM) Class B JESD22-A115-B Storage Temperature - 40°C - 135°C LED Junction Temperature [1] 115°C Operating CaseTemperature at 700 mA - 40°C - 85°C 121°C at 2 ATM Autoclave Conditions Reverse Voltage (Vr) LUXEON S LEDs are not designed to be driven in reverse bias Notes for Table 4: 1. Proper current derating must be observed to maintain junction temperature below the maximum. LUXEON S Datasheet DS80 20130907 ©2013 Philips Lumileds Lighting Company. 4 Mechanical Dimensions Figure 1. Package outline drawing. Notes for Figure 1: • Do not handle device by the lens. Excessive force on the lens may damage the lens itself or the interior of the device. • Drawings not to scale. • All dimensions are in millimeters. • The Thermal Pad is electrically isolated from the Anode and Cathode contact pads. LUXEON S Datasheet DS80 20130907 ©2013 Philips Lumileds Lighting Company. 5 Relative Spectral Distribution vs. Wavelength Characteristics Relative Spectra at Test Current, Junction Temperature = 85°C Figure 2. Color Spectra of LXSx-PWxx. LUXEON S Datasheet DS80 20130907 ©2013 Philips Lumileds Lighting Company. 6 Light Output Characteristics Relative Light Output vs. Junction Temperature Test Current = 700 mA Figure 3. Relative light output vs. junction temperature, LXSx-PWxx. Relative Light Output vs. Forward Current Junction Temperature = 85°C Figure 4. Typical relative light output vs. forward current, LXSx-PWxx. LUXEON S Datasheet DS80 20130907 ©2013 Philips Lumileds Lighting Company. 7 Typical Forward Current Characterisics Junction Temperature = 85ºC Figure 5. Typical forward current vs. forward voltage, LXSx-PWxx. LUXEON S Datasheet DS80 20130907 ©2013 Philips Lumileds Lighting Company. 8 Typical Radiation Pattern Typical Spatial Radiation Pattern Figure 6. Typical representative spatial radiation pattern for LXSx-PWxx. Typical Polar Radiation Pattern Figure 7. Typical representative polar radiation pattern for LXSx-PWxx. LUXEON S Datasheet DS80 20130907 ©2013 Philips Lumileds Lighting Company. 9 Packaging Figure 8. LUXEON S1000 devices are packaged in stackable trays containing 100 pieces per tray. The trays are designed to provide easy access to the thermal pad at the bottom of the LUXEON S1000 emitter. LUXEON S Datasheet DS80 20130907 ©2013 Philips Lumileds Lighting Company. 10 Product Binning and Labeling Purpose of Product Binning In the manufacturing of semiconductor products, there is a variation of performance around the average values given in the technical data sheets. For this reason, Philips Lumileds bins the LED components for luminous flux, color and forward voltage (Vf). Decoding Product Bin Labeling LUXEON S1000 emitters are labeled using a four digit alphanumeric code (CAT code) depicting the bin values for emitters packaged in a single tray. All emitters packaged within a tray are of the same 3-variable combination. Trays of LUXEON S1000 emitters are labeled with a four digit alphanumeric CAT code following the format below. W XY Z W = Flux bin (A,B,C etc.) X = CCT (X=8 for 2700K, X=7 for 3000K, X=6 for 3500K and X=5 for 4000K) Y = Color bin (Y=A for 3-step MacAdam ellipse above BBL, Y=B for 3-step MacAdam ellipse below BBL) - see Figure 9 below here for visual illustration of above and below BBL binning Z = Vf bin (G,H,J etc.) Figure 9. Color binning for LUXEON S1000. LUXEON S Datasheet DS80 20130907 ©2013 Philips Lumileds Lighting Company. 11 CRI Product Labeling CRI marking can be found on top edge of the AlN DBC substrate as shown in Figure 10 below here (where two bare AlN DBC substrates are shown with no LED attached). One marking indicates the part is a 80CRI part. Two marking indicates the part is a 90CRI part. Figure 10. CRI Marking. Luminous Flux Bins Table 5 lists the standard photometric luminous flux bins for LUXEON S1000 emitters (tested and binned at 700 mA with junction temperature of 85°C). Although several bins are outlined, product availability in a particular bin varies by production run and by product performance. Table 5. Flux Bins Bin Code Min Photometric Flux (lm) Max Photometric Flux (lm) A 1050 1100 B 1100 1150 C 1150 1200 L 1200 1250 M 1250 1300 N 1300 1360 P 1360 1420 Q 1420 1480 R 1480 1540 S 1540 1615 T 1615 1690 U 1690 1765 V 1765 1840 LUXEON S Datasheet DS80 20130907 ©2013 Philips Lumileds Lighting Company. 12 LUXEON S1000 Color Bin Structure Figure 9. Color Binstructure of LXSx-PWxx. Table 6. LUXEON S Product Characteristics for 3-step MacAdam Ellipse Based on: ANSI C78.376-2001 and ANSI C78.377-2008 ANSI Bins xcenter ycenter 2700K 0.4578 0.4101 3000K 0.4338 0.4030 3500K 0.4073 0.3917 4000K 0.3818 0.3797 Major Axis, a Minor Axis, b Elliptical Angle 0.0081 0.0042 53.70° 0.00834 0.00408 53.22° 0.00927 0.00414 54.00° 0.00939 0.00402 53.72° Table 7. LUXEON S Product Characteristics for 4-step MacAdam Ellipse Based on: ANSI C78.376-2001 and ANSI C78.377-2008 ANSI Bins xcenter ycenter Major Axis, a Minor Axis, b Elliptical Angle 2700K 0.4578 0.4101 0.01080 0.00560 53.70° 3000K 0.4338 0.4030 0.01112 0.00544 53.22° 3500K 0.4073 0.3917 0.01236 0.00552 54.00° 4000K 0.3818 0.3797 0.01252 0.00536 53.72° Notes for Tables 6 and 7: 1. Philips Lumileds maintains a tester tolerence of ± 0.005 on x, y color coordinates. LUXEON S Datasheet DS80 20130907 ©2013 Philips Lumileds Lighting Company. 13 Forward Voltage Bins Table 8 lists minimum and maximum Vf bin values per emitter. Although several bins are outlined, product availability in a particular bin varies by production run and by product performance. Table 8. Vf Bins Bin Code Minimum Forward Voltage (V) Maximum Forward Voltage (V) G 23.5 24.5 H 24.5 26 J 26 27.5 K 27.5 29 LUXEON S Datasheet DS80 20130907 ©2013 Philips Lumileds Lighting Company. 14 Company Information Philips Lumileds is a leading provider of LEDs for everyday lighting applications. The company’s records for light output, efficacy and thermal management are direct results of the ongoing commitment to advancing solid-state lighting technology and enabling lighting solutions that are more environmentally friendly, help reduce CO2 emissions and reduce the need for power plant expansion. Philips Lumileds LUXEON® LEDs are enabling never before possible applications in outdoor lighting, shop lighting, home lighting, digital imaging, display and automotive lighting. Philips Lumileds is a fully integrated supplier, producing core LED material in all three base colors, (Red, Green, Blue) and white. Philips Lumileds has R&D centers in San Jose, California and in the Netherlands, and production capabilities in San Jose, Singapore and Penang, Malaysia. Founded in 1999, Philips Lumileds is the high flux LED technology leader and is dedicated to bridging the gap between solid-state technology and the lighting world. More information about the company’s LUXEON LED products and solid-state lighting technologies can be found at www.philipslumileds.com. Philips Lumileds Lighting Company shall not be liable for any kind of loss of data or any other damages, direct, indirect or consequential, resulting from the use of the provided information and data. Although Philips Lumileds Lighting Company has attempted to provide the most accurate information and data, the materials and services information and data are provided “as is” and Philips Lumileds Lighting Company neither warranties, nor guarantees the contents and correctness of the provided information and data. Philips Lumileds Lighting Company reserves the right to make changes without notice. You as user agree to this disclaimer and user agreement with the download or use of the provided materials, information and data. ©2013 Philips Lumileds Lighting Company. All rights reserved. LUXEON is a registered trademark of the Philips Lumileds Lighting Company in the United States and other countries. www.philipslumileds.com www.philipslumileds.cn.com LUXEON S Datasheet DS80 20130907