Product Folder Sample & Buy Support & Community Tools & Software Technical Documents LMV931-N, LMV931-N-Q1 LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 SNOS993O – NOVEMBER 2001 – REVISED DECEMBER 2014 LMV93x-N/-N-Q1 Single, Dual, Quad 1.8-V, RRIO Operational Amplifiers 1 Features • 1 • • • • • • • • • Typical 1.8-V Supply Values; Unless Otherwise Noted Available in Automotive AEC-Q100 Grade 1 Specified at 1.8-V, 2.7-V and 5-V Output Swing – With 600-Ω Load 80 mV from Rail – With 2-kΩ Load 30 mV from Rail VCM 200 mV Beyond Rails Supply Current (per Channel) 100 μA Gain Bandwidth Product 1.4 MHz Maximum VOS 4.0 mV Ultra Tiny Packages Temperature Range −40°C to 125°C LMV93x-N devices exhibit an excellent speed-power ratio, achieving 1.4-MHz gain bandwidth product at 1.8-V supply voltage with very low supply current. The LMV93x-N devices can drive a 600-Ω load and up to 1000-pF capacitive load with minimal ringing. These devices also have a high DC gain of 101 dB, making them suitable for low-frequency applications. The single LMV93x-N is offered in space-saving 5-pin SC70 and SOT-23 packages. The dual LMV932-N are in 8-pin VSSOP and SOIC packages and the quad LMV934-N are in 14-pin TSSOP and SOIC packages. These small packages are ideal solutions for area constrained PC boards and portable electronics such as mobile phones and tablets. The LMV93x-N-Q1 family retains all the LMV93x-N family features while adding AEC-Q100 Grade 1 qualification for automotive applications. Device Information(1) 2 Applications • • • • • • Mobile Phones Tablets Wearables Health Monitoring Portable and Battery-Powered Electronic Equipment Battery Monitoring 3 Description The LMV93x-N family (LMV931-N single, LMV932-N dual and LMV934-N quad) are low-voltage, lowpower operational amplifiers. The LMV93x-N family operates from 1.8-V to 5.5-V supply voltages and have rail-to-rail input and output. The input commonmode voltage extends 200 mV beyond the supplies which enables user enhanced functionality beyond the supply voltage range. The output can swing railto-rail unloaded and within 105 mV from the rail with 600-Ω load at 1.8-V supply. The LMV93x-N devices are optimized to work at 1.8 V, which make them ideal for portable two-cell, battery-powered systems and single-cell Li-Ion systems. PART NUMBER PACKAGE BODY SIZE (NOM) LMV931-N SOT-23 (5) 2.90 mm × 1.60 mm LMV931-N-Q1 SC-70 (5) 2.00 mm × 1.25 mm LMV932-N VSSOP (8) 3.00 mm × 3.00 mm LMV932-N-Q1 SOIC (8) 4.90 mm × 3.91 mm LMV934-N TSSOP (8) 5.00 mm × 4.40 mm LMV934-N-Q1 SOIC (14) 8.60 mm × 3.90 mm (1) For all available packages, see the orderable addendum at the end of the datasheet. High-Side Current Sense Amplifier 1 An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications, intellectual property matters and other important disclaimers. PRODUCTION DATA. LMV931-N, LMV931-N-Q1 LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 SNOS993O – NOVEMBER 2001 – REVISED DECEMBER 2014 www.ti.com Table of Contents 1 2 3 4 5 6 Features .................................................................. Applications ........................................................... Description ............................................................. Revision History..................................................... Pin Configuration and Functions ......................... Specifications......................................................... 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 6.10 6.11 6.12 7 1 1 1 2 3 4 Absolute Maximum Ratings ...................................... 4 Handling Ratings - Commercial ................................ 4 Handling Ratings - Automotive ................................. 4 Recommended Operating Ratings............................ 4 Thermal Information .................................................. 4 DC Electrical Characteristics 1.8 V .......................... 5 AC Electrical Characteristics 1.8 V ........................... 6 DC Electrical Characteristics 2.7 V .......................... 7 AC Electrical Characteristics 2.7 V ........................... 8 Electrical Characteristics 5 V DC ............................ 9 AC Electrical Characteristics 5 V ......................... 10 Typical Characteristics .......................................... 11 Detailed Description ............................................ 16 7.1 Overview ................................................................. 16 7.2 Functional Block Diagram ....................................... 16 7.3 Feature Description................................................. 16 7.4 Device Functional Modes........................................ 16 8 Application and Implementation ........................ 18 8.1 Application Information............................................ 18 8.2 Typical Applications ............................................... 18 8.3 Dos and Don'ts ....................................................... 21 9 Power Supply Recommendations...................... 21 10 Layout................................................................... 21 10.1 Layout Guidelines ................................................. 21 10.2 Layout Example .................................................... 22 11 Device and Documentation Support ................. 23 11.1 11.2 11.3 11.4 11.5 11.6 Device Support .................................................... Documentation Support ....................................... Related Links ........................................................ Trademarks ........................................................... Electrostatic Discharge Caution ............................ Glossary ................................................................ 23 23 23 23 23 23 12 Mechanical, Packaging, and Orderable Information ........................................................... 23 4 Revision History NOTE: Page numbers for previous revisions may differ from page numbers in the current version. Changes from Revision N (June 2014) to Revision O • Page Added Pin Configuration and Functions section, Handling Rating table, Feature Description section, Device Functional Modes, Application and Implementation section, Power Supply Recommendations section, Layout section, Device and Documentation Support section, and Mechanical, Packaging, and Orderable Information section ................................................................................................................................................................................... 1 Changes from Revision M (November 2013) to Revision N Page • Complete rewrite for GDS standard. ...................................................................................................................................... 1 • Added LMV934-N-Q1. The other Q grades were added in previous revision........................................................................ 1 Changes from Revision L (March 2013) to Revision M Page • Added Automotive Q Grade. ................................................................................................................................................. 1 • Added Output Swing for Q-Grade in all Electrical Tables ...................................................................................................... 6 2 Submit Documentation Feedback Copyright © 2001–2014, Texas Instruments Incorporated Product Folder Links: LMV931-N LMV931-N-Q1 LMV932-N LMV932-N-Q1 LMV934-N LMV934-N-Q1 LMV931-N, LMV931-N-Q1 LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 www.ti.com SNOS993O – NOVEMBER 2001 – REVISED DECEMBER 2014 5 Pin Configuration and Functions DBV and DCK Package 5-Pin SC-70 and SOT-23 LMV931-N, LMV931-N-Q1 Top View DGK and D Package 8-Pin VSSOP and SOIC LMV932-N, LMV932-N-Q1 Top View 1 8 + V OUT A A 2 - + 7 -IN A OUT B 3 6 +IN A V - -IN B B + 4 5 +IN B DGK and D Package 14-Pin TSSOP and SOIC LMV934-N, LMV934-N-Q1 Top View Pin Functions: LMV931 PIN NAME LMV931 I/O DESCRIPTION DBV, DCK NO. +IN 1 I Noninverting Input -IN 3 I Inverting Input OUT 4 O Output V- 2 P Negative Supply V+ 5 P Positive Supply Pin Functions: LMV932 and LMV934 PIN NAME +IN A LMV932 LMV934 D, DGK NO. D, PW NO. I/O DESCRIPTION 3 3 I Noninverting input, channel A +IN B 5 5 I Noninverting input, channel B +IN C — 10 I Noninverting input, channel C +IN D — 12 I Noninverting input, channel D –IN A 2 2 I Inverting input, channel A –IN B 6 6 I Inverting input, channel B –IN C — 9 I Inverting input, channel C –IN D — 13 I Inverting input, channel D OUT A 1 1 O Output, channel A OUT B 7 7 O Output, channel B OUT C — 8 O Output, channel C OUT D — 14 O Output, channel D V+ 8 4 P Positive (highest) power supply V– 4 11 P Negative (lowest) power supply Copyright © 2001–2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV931-N LMV931-N-Q1 LMV932-N LMV932-N-Q1 LMV934-N LMV934-N-Q1 3 LMV931-N, LMV931-N-Q1 LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 SNOS993O – NOVEMBER 2001 – REVISED DECEMBER 2014 www.ti.com 6 Specifications 6.1 Absolute Maximum Ratings (1) (2) See . Supply voltage ( V+– V− ) MIN MAX –0.3 6 V- Differential input voltage (2) (3) V + (V ) - 0.3 (V ) + 0.3 –40 150 Junction temperature (3) (1) V+ - Voltage at input/output pins UNIT °C Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Recommended Operating Conditions indicate conditions for which the device is intended to be functional, but specific performance is not specified. For specifications and the test conditions, see the Electrical Characteristics. If Military/Aerospace specified devices are required, please contact the TI Sales Office/Distributors for availability and specifications. The maximum power dissipation is a function of TJ(max) , RθJA, and TA. The maximum allowable power dissipation at any ambient temperature is PD = (TJ(max)–TA)/RθJA. All numbers apply for packages soldered directly into a PC board. 6.2 Handling Ratings - Commercial Tstg Electrostatic discharge V(ESD) (1) (2) (3) (4) MIN MAX UNIT –65 150 °C Human body model (HBM), per ANSI/ESDA/JEDEC JS001, all pins (1) (2) –2000 2000 Charged device model (CDM), per JEDEC specification JESD22-C101, all pins (3) –750 750 Machine Model (MM) (4) –200 200 Storage temperature range V JEDEC document JEP155 states that 500V HBM allows safe manufacturing with a standard ESD control process. AEC Q100-002 indicates HBM stressing is done in accordance with the ANSI/ESDA/JEDEC JS-001 specification. JEDEC document JEP157 states that 250V CDM allows safe manufacturing with a standard ESD control process. Machine model, 200 Ω in series with 100-pF. 6.3 Handling Ratings - Automotive MIN Tstg Storage temperature range V(ESD) Electrostatic discharge UNIT °C –65 150 Human body model (HBM), per AEC Q100-002 (1) –2000 2000 Charged device model (CDM), per AEC Q100-011 –750 750 –200 200 Machine Model (MM) (1) (2) MAX (2) V AEC Q100-002 indicates HBM stressing is done in accordance with the ANSI/ESDA/JEDEC JS-001 specification. Machine model, 200 Ω in series with 100-pF. 6.4 Recommended Operating Ratings (1) See . MIN MAX Supply Voltage Range ( V+– V− ) 1.8 5.5 V Temperature Range −40 125 °C (1) UNIT Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Recommended Operating Conditions indicate conditions for which the device is intended to be functional, but specific performance is not specified. For specifications and the test conditions, see the Electrical Characteristics. 6.5 Thermal Information LMV921 THERMAL METRIC (1) DCK LMV922 DBV DGK 265 235 5 PINS RθJA (1) 4 Junction-to-ambient thermal resistance 414 LMV924 D DGK 175 155 8 PINS D UNIT 127 °C/W 14 PINS For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953. Submit Documentation Feedback Copyright © 2001–2014, Texas Instruments Incorporated Product Folder Links: LMV931-N LMV931-N-Q1 LMV932-N LMV932-N-Q1 LMV934-N LMV934-N-Q1 LMV931-N, LMV931-N-Q1 LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 www.ti.com SNOS993O – NOVEMBER 2001 – REVISED DECEMBER 2014 6.6 DC Electrical Characteristics 1.8 V Unless otherwise specified, all limits specified for TJ = 25°C. V+ = 1.8 V, V − = 0 V, VCM = V+/2, VO = V+/2 and RL > 1 MΩ. PARAMETER TEST CONDITIONS LMV931 (Single) VOS Input Offset Voltage MIN 25°C TYP MAX 1 4 (1) Full Range LMV932 (Dual), LMV934 (Quad) 25°C 1 5.5 Full Range Full Range 5.5 IB Input Bias Current 25°C 15 μV/°C 35 Full Range 50 25°C 13 25 Full Range IS Supply Current (per channel) 40 25°C 103 185 Full Range CMRR PSRR CMVR Common-Mode Rejection Ratio Power Supply Rejection Ratio Input Common-Mode Voltage Range 25°C 60 Full Range 55 LMV932 and LMV934 0 ≤ VCM ≤ 0.6 V 1.4 V ≤ VCM ≤ 1.8 V (2) 25°C 55 Full Range 50 −0.2 V ≤ VCM ≤ 0 V 1.8 V ≤ VCM ≤ 2.0 V 25°C 50 72 + 25°C 75 100 Full Range 70 For CMRR Range ≥ 50dB 25°C −40°C to 85°C 125°C Large Signal Voltage Gain LMV931-N (Single) LMV931-N-Q1 (Single) AV Large Signal Voltage Gain LMV932-N (Dual) LMV932-N-Q1 (Dual) LMV934-N (Quad) LMV934-N-Q1 (Quad) VO (1) (2) Output Swing 205 LMV931, 0 ≤ VCM ≤ 0.6 V 1.4 V ≤ VCM ≤ 1.8 V (2) 1.8 V ≤ V ≤ 5 V V− − 0.2 − V V− + 0.2 RL = 600 Ω to 0.9 V, VO = 0.2 V to 1.6 V, VCM = 0.5 V 25°C 77 Full Range 73 RL = 2 kΩ to 0.9 V, VO = 0.2 V to 1.6 V, VCM = 0.5 V 25°C 80 Full Range 75 RL = 600 Ω to 0.9 V, VO = 0.2 V to 1.6 V, VCM = 0.5 V 25°C 75 Full Range 72 RL = 2 kΩ to 0.9 V, VO = 0.2 V to 1.6 V, VCM = 0.5 V 25°C 78 Full Range 75 RL = 600 Ω to 0.9 V VIN = ±100 mV 25°C RL = 2 kΩ to 0.9 V VIN = ±100 mV mV 7.5 Input Offset Voltage Average Drift Input Offset Current mV 6 TCVOS IOS UNIT 1.65 78 1.63 25°C 1.75 Full Range 1.74 nA μA dB 76 dB −0.2 to 2.1 dB dB V+ + 0.2 V+ V V+ − 0.2 101 dB 105 dB 90 dB 100 dB 1.72 0.077 Full Range nA 0.105 V 0.120 1.77 0.024 0.035 V 0.04 Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. For specified temperature ranges, see the CMVR parameter in DC Electrical Characteristics 1.8 V for the input common-mode voltage specifications. Copyright © 2001–2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV931-N LMV931-N-Q1 LMV932-N LMV932-N-Q1 LMV934-N LMV934-N-Q1 5 LMV931-N, LMV931-N-Q1 LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 SNOS993O – NOVEMBER 2001 – REVISED DECEMBER 2014 www.ti.com DC Electrical Characteristics 1.8 V (continued) Unless otherwise specified, all limits specified for TJ = 25°C. V+ = 1.8 V, V − = 0 V, VCM = V+/2, VO = V+/2 and RL > 1 MΩ. PARAMETER TEST CONDITIONS RL = 600 Ω to 0.9 V VIN = ±100 mV Output Swing LMV932-N-Q1 (Dual) LMV934-N-Q1 (Quad) VO RL = 2 kΩ to 0.9 V VIN = ±100 mV 25°C (3) Output Short Circuit Current 1.65 Full Range 1.63 25°C 1.75 (1) Sinking, VO = 1.8 V VIN = −100 mV 25°C 7 Full Range 5 Full Range 4 UNIT 0.105 V 0.173 1.77 1.74 25°C MAX 1.72 0.024 Sourcing, VO = 0 V VIN = 100 mV (3) TYP 0.077 Full Range IO MIN 0.035 V 0.055 8 mA 3.3 9 mA Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 150°C. Output currents in excess of 45 mA over long term may adversely affect reliability. 6.7 AC Electrical Characteristics 1.8 V Unless otherwise specified, all limits specified for TJ = 25°C. V+ = 1.8 V, V − = 0 V, VCM = V+/2, VO = V+/2 and RL > 1 MΩ. PARAMETER TEST CONDITIONS Slew Rate GBW Φm Gm Gain Margin en Input-Referred Voltage Noise f = 10 kHz, VCM = 0.5 V in Input-Referred Current Noise f = 10 kHz Total Harmonic Distortion f = 1 kHz, AV = +1 RL = 600 Ω, VIN = 1 VPP Amplifier-to-Amplifier Isolation See (3) THD (1) (2) (3) 6 See (2) SR . MIN TYP (1) MAX UNIT 0.35 V/μs Gain-Bandwidth Product 1.4 MHz Phase Margin 67 deg 7 dB 60 nV/√Hz 0.08 pA/√Hz 0.023% 123 dB Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. Connected as voltage follower with input step from V− to V+. Number specified is the slower of the positive and negative slew rates. Input referred, RL = 100 kΩ connected to V+/2. Each amplifier excited in turn with 1 kHz to produce VO = 3 VPP (For Supply Voltages <3 V, VO = V+). Submit Documentation Feedback Copyright © 2001–2014, Texas Instruments Incorporated Product Folder Links: LMV931-N LMV931-N-Q1 LMV932-N LMV932-N-Q1 LMV934-N LMV934-N-Q1 LMV931-N, LMV931-N-Q1 LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 www.ti.com SNOS993O – NOVEMBER 2001 – REVISED DECEMBER 2014 6.8 DC Electrical Characteristics 2.7 V Unless otherwise specified, all limits specified for TJ = 25°C. V+ = 2.7 V, V − = 0 V, VCM = V+/2, VO = V+/2 and RL > 1 MΩ. PARAMETER TEST CONDITIONS LMV931 (Single) VOS Input Offset Voltage MIN 25°C TYP MAX 1 4 (1) Full Range LMV932 (Dual) LMV934 (Quad) 1 5.5 Full Range Input Offset Voltage Average Drift Full Range IB Input Bias Current 25°C Input Offset Current 5.5 μV/°C 15 35 50 25°C 8 25 Full Range IS Supply Current (per channel) 40 25°C 105 190 Full Range CMRR Common-Mode Rejection Ratio PSRR Power Supply Rejection Ratio VCM Input Common-Mode Voltage Range 25°C 60 Full Range 55 LMV932 and LMV934 0 ≤ VCM ≤ 1.5 V 2.3 V ≤ VCM ≤ 2.7 V (2) 25°C 55 Full Range 50 25°C + 1.8 V ≤ V ≤ 5 V VCM = 0.5 V For CMRR Range ≥ 50 dB 25°C AV VO Large Signal Voltage Gain LMV932-N (Dual) LMV932-N-Q1 (Dual) LMV934-N (Quad) LMV934-N-Q1 (Quad) Output Swing 75 100 Full Range 70 VO (1) (2) V V− + 0.2 RL = 600 Ω to 1.35 V, VO = 0.2 V to 2.5 V 25°C 87 Full Range 86 RL = 2 kΩ to 1.35 V, VO = 0.2 V to 2.5 V 25°C 92 Full Range 91 RL = 600 Ω to 1.35 V, VO = 0.2 V to 2.5 V 25°C 78 Full Range 75 RL = 2 kΩ to 1.35 V, VO = 0.2 V to 2.5 V 25°C 81 Full Range 78 RL = 600 Ω to 1.35 V VIN = ±100 mV 25°C RL = 600 Ω to 1.35 V VIN = ±100 mV Output Swing LMV932-N-Q1 (Dual) LMV934-N-Q1 (Quad) − RL = 2 kΩ to 1.35 V VIN = ±100 mV 2.55 2.53 25°C 2.65 −0.2 to 3.0 dB dB V+ + 0.2 V+ 2.64 25°C 2.55 104 2.53 25°C 2.65 Full Range 2.64 dB 110 dB 90 dB 100 dB 2.62 0.110 V 0.130 2.675 0.04 V 0.045 2.62 0.083 Full Range V V+ − 0.2 0.025 Full Range μA dB 0.083 Full Range nA dB 25°C V− − 0.2 nA 80 74 −40°C to 85°C RL = 2 kΩ to 1.35 V VIN = ±100 mV 81 50 125°C Large Signal Voltage Gain LMV931-N (Single) LMV931-N-Q1 (Single) 210 LMV931, 0 ≤ VCM ≤ 1.5 V 2.3 V ≤ VCM ≤ 2.7 V (2) −0.2 V ≤ VCM ≤ 0 V 2.7 V ≤ VCM ≤ 2.9 V mV 7.5 Full Range IOS mV 6 25°C TCVOS UNIT 0.110 V 0.187 2.675 0.025 0.04 V 0.059 Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. For specified temperature ranges, see the CMVR parameter in DC Electrical Characteristics 1.8 V for the input common-mode voltage specifications. Copyright © 2001–2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV931-N LMV931-N-Q1 LMV932-N LMV932-N-Q1 LMV934-N LMV934-N-Q1 7 LMV931-N, LMV931-N-Q1 LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 SNOS993O – NOVEMBER 2001 – REVISED DECEMBER 2014 www.ti.com DC Electrical Characteristics 2.7 V (continued) Unless otherwise specified, all limits specified for TJ = 25°C. V+ = 2.7 V, V − = 0 V, VCM = V+/2, VO = V+/2 and RL > 1 MΩ. PARAMETER Output Short Circuit Current (3) IO (3) TEST CONDITIONS MIN TYP 30 Sourcing, VO = 0 V VIN = +100 mV 25°C 20 Full Range 15 Sinking, VO = 2.7 V VIN = −100 mV 25°C 18 Full Range 12 (1) MAX UNIT mA 25 mA Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 150°C. Output currents in excess of 45 mA over long term may adversely affect reliability. 6.9 AC Electrical Characteristics 2.7 V Unless otherwise specified, all limits specified for TJ = 25°C. V+ = 2.7 V, V − = 0 V, VCM = 1.0 V, VO = 1.35 V and RL > 1 MΩ. PARAMETER TEST CONDITIONS See (2) MIN TYP (1) MAX UNIT SR Slew Rate 0.4 V/µs GBW Gain-Bandwidth Product 1.4 MHz Φm Phase Margin 70 deg Gm Gain Margin en Input-Referred Voltage Noise f = 10 kHz, VCM = 0.5 V in Input-Referred Current Noise f = 10 kHz THD Total Harmonic Distortion f = 1 kHz, AV = +1 RL = 600 Ω, VIN = 1 VPP Amp-to-Amp Isolation (1) (2) (3) 8 See (3) 7.5 dB 57 nV√Hz 0.08 pA/√Hz 0.022% 123 dB Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. Connected as voltage follower with input step from V− to V+. Number specified is the slower of the positive and negative slew rates. Input referred, RL = 100 kΩ connected to V+/2. Each amplifier excited in turn with 1 kHz to produce VO = 3 VPP (For Supply Voltages <3 V, VO = V+). Submit Documentation Feedback Copyright © 2001–2014, Texas Instruments Incorporated Product Folder Links: LMV931-N LMV931-N-Q1 LMV932-N LMV932-N-Q1 LMV934-N LMV934-N-Q1 LMV931-N, LMV931-N-Q1 LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 www.ti.com SNOS993O – NOVEMBER 2001 – REVISED DECEMBER 2014 6.10 Electrical Characteristics 5 V DC Unless otherwise specified, all limits specified for TJ = 25°C. V+ = 5 V, V − = 0 V, VCM = V+/2, VO = V+/2 and RL > 1 MΩ. PARAMETER TEST CONDITIONS LMV931 (Single) VOS Input Offset Voltage TCVOS Input Offset Voltage Average Drift IB Input Bias Current MIN 25°C TYP MAX 1 4 (1) Full Range LMV932 (Dual) LMV934 (Quad) 25°C 1 5.5 Full Range μV/°C 25°C 14 35 50 25°C 9 25 Full Range IS Supply Current (per channel) 40 25°C 116 210 Full Range CMRR PSRR Power Supply Rejection Ratio CMVR Input Common-Mode Voltage Range 25°C 60 Full Range 55 −0.2 V ≤ VCM ≤ 0 V 5.0 V ≤ VCM ≤ 5.2 V 25°C 1.8 V ≤ V+ ≤ 5 V VCM = 0.5 V For CMRR Range ≥ 50 dB 25°C AV VO Large Signal Voltage Gain LMV932-N (Dual) LMV932-N-Q1 (Dual) LMV934-N (Quad) LMV934-N-Q1 (Quad) Output Swing 78 25°C 75 100 Full Range 70 VO (2) V + 0.3 25°C 88 Full Range 87 RL = 2 kΩ to 2.5 V, VO = 0.2 V to 4.8 V 25°C 94 Full Range 93 RL = 600 Ω to 2.5 V, VO = 0.2 V to 4.8 V 25°C 81 Full Range 78 RL = 2 kΩ to 2.5 V, VO = 0.2 V to 4.8 V 25°C 85 Full Range 82 RL = 600 Ω to 2.5 V VIN = ±100 mV 25°C 4.855 Full Range 4.835 25°C 4.945 Full Range 4.935 25°C 4.855 RL = 2 kΩ to 2.5 V VIN = ±100 mV −0.2 to 5.3 4.807 4.945 μA dB V+ + 0.2 V+ V + V − 0.3 102 dB 113 dB 90 dB 100 dB 4.890 0.160 V 0.180 4.967 0.065 V 0.075 4.890 0.120 25°C nA dB 0.037 Full Range nA dB 0.120 0.160 V 0.218 4.967 0.037 Full Range (1) V− − RL = 600 Ω to 2.5 V, VO = 0.2 V to 4.8 V RL = 600 Ω to 2.5 V VIN = ±100 mV Output Swing LMV932-N-Q1 (Dual) LMV934-N-Q1 (Quad) V− − 0.2 −40°C to 85°C RL = 2 kΩ to 2.5 V VIN = ±100 mV 86 50 125°C Large Signal Voltage Gain LMV931-N (Single) LMV931-N-Q1 (Single) 230 0 ≤ VCM ≤ 3.8 V 4.6 V ≤ VCM ≤ 5.0 V (2) Common-Mode Rejection Ratio mV 7.5 5.5 Input Offset Current mV 6 Full Range IOS UNIT 4.935 0.065 V 0.075 Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. For specified temperature ranges, see the CMVR parameter in DC Electrical Characteristics 1.8 V for the input common-mode voltage specifications. Copyright © 2001–2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV931-N LMV931-N-Q1 LMV932-N LMV932-N-Q1 LMV934-N LMV934-N-Q1 9 LMV931-N, LMV931-N-Q1 LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 SNOS993O – NOVEMBER 2001 – REVISED DECEMBER 2014 www.ti.com Electrical Characteristics 5 V DC (continued) Unless otherwise specified, all limits specified for TJ = 25°C. V+ = 5 V, V − = 0 V, VCM = V+/2, VO = V+/2 and RL > 1 MΩ. PARAMETER Output Short Circuit Current (3) IO (3) TEST CONDITIONS MIN TYP 100 LMV931, Sourcing, VO = 0 V VIN = +100 mV 25°C 80 Full Range 68 Sinking, VO = 5 V VIN = −100 mV 25°C 58 Full Range 45 (1) MAX UNIT mA 65 mA Applies to both single-supply and split-supply operation. Continuous short circuit operation at elevated ambient temperature can result in exceeding the maximum allowed junction temperature of 150°C. Output currents in excess of 45 mA over long term may adversely affect reliability. 6.11 AC Electrical Characteristics 5 V Unless otherwise specified, all limits specified for TJ = 25°C. V+ = 5 V, V − = 0 V, VCM = V+/2, VO = 2.5 V and R L > 1 MΩ. PARAMETER TEST CONDITIONS See . (2) MIN TYP (1) MAX UNIT SR Slew Rate 0.42 V/µs GBW Gain-Bandwidth Product 1.5 MHz Φm Phase Margin 71 deg Gm Gain Margin en Input-Referred Voltage Noise f = 10 kHz, VCM = 1 V in Input-Referred Current Noise f = 10 kHz THD Total Harmonic Distortion f = 1 kHz, AV = 1 RL = 600 Ω, VO = 1 VPP Amplifier-to-Amplifier Isolation See (3) (1) (2) (3) 10 8 dB 50 nV/√Hz 0.08 pA/√Hz 0.022% 123 dB Typical values represent the most likely parametric norm as determined at the time of characterization. Actual typical values may vary over time and will also depend on the application and configuration. Connected as voltage follower with input step from V− to V+. Number specified is the slower of the positive and negative slew rates. Input referred, RL = 100 kΩ connected to V+/2. Each amplifier excited in turn with 1 kHz to produce VO = 3 VPP (For Supply Voltages <3 V, VO = V+). Submit Documentation Feedback Copyright © 2001–2014, Texas Instruments Incorporated Product Folder Links: LMV931-N LMV931-N-Q1 LMV932-N LMV932-N-Q1 LMV934-N LMV934-N-Q1 LMV931-N, LMV931-N-Q1 LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 www.ti.com SNOS993O – NOVEMBER 2001 – REVISED DECEMBER 2014 6.12 Typical Characteristics Unless otherwise specified, VS = 5 V, single-supply, TA = 25°C. 160 100 125°C SUPPLY CURRENT (éA) 140 VS = 5V 85°C 10 ISOURCE (mA) 120 100 25°C 80 -40°C 60 VS = 2.7V 1 VS = 1.8V 0.1 40 20 0 0 1 2 3 4 5 6 0.01 0.001 100 VS = 5V ISINK (mA) 10 VS = 2.7V 1 VS = 1.8V 0.01 0.001 0.01 0.1 10 1 OUTPUT VOLTAGE REF TO GND (V) Figure 3. Sinking Current vs. Output Voltage OUTPUT VOLTAGE PROXIMITY TO SUPPLY VOLTAGE (mV ABSOLUTE VALUE) 0.1 1 10 Figure 2. Sourcing Current vs. Output Voltage OUTPUT VOLTAGE PROXIMITY TO SUPPLY VOLTAGE (mV ABSOLUTE VALUE) Figure 1. Supply Current vs. Supply Voltage (LMV931-N) 0.1 0.01 OUTPUT VOLTAGE REFERENCED TO V+ (V) SUPPLY VOLTAGE (V) 140 RL = 600: 130 NEGATIVE SWING 120 110 100 90 80 POSITIVE SWING 70 60 0 1 4 2 3 SUPPLY VOLTAGE (V) 5 6 Figure 4. Output Voltage Swing vs. Supply Voltage 45 RL = 2k: 40 NEGATIVE SWING 35 30 25 POSITIVE SWING 20 0 1 2 3 4 5 6 SUPPLY VOLTAGE (V) Figure 5. Output Voltage Swing vs. Supply Voltage Copyright © 2001–2014, Texas Instruments Incorporated Figure 6. Gain and Phase vs. Frequency Submit Documentation Feedback Product Folder Links: LMV931-N LMV931-N-Q1 LMV932-N LMV932-N-Q1 LMV934-N LMV934-N-Q1 11 LMV931-N, LMV931-N-Q1 LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 SNOS993O – NOVEMBER 2001 – REVISED DECEMBER 2014 www.ti.com Typical Characteristics (continued) Unless otherwise specified, VS = 5 V, single-supply, TA = 25°C. Figure 7. Gain and Phase vs. Frequency Figure 8. Gain and Phase vs. Frequency 90 VS = 5V 85 CMRR (dB) 80 VS = 2.7V 75 VS = 1.8V 70 65 60 1k 100 FREQUENCY (Hz) 10 Figure 10. CMRR vs. Frequency Figure 9. Gain and Phase vs. Frequency 100 90 PSRR (dB) 80 70 -PSRR 60 50 40 30 10 100 1k FREQUENCY (Hz) Figure 11. PSRR vs. Frequency Submit Documentation Feedback 10k INPUT VOLTAGE NOISE (nV/ Hz) 1000 VS = 5V +PSRR 12 10k 100 10 10 100 1k 10k 100k FREQUENCY (Hz) Figure 12. Input Voltage Noise vs. Frequency Copyright © 2001–2014, Texas Instruments Incorporated Product Folder Links: LMV931-N LMV931-N-Q1 LMV932-N LMV932-N-Q1 LMV934-N LMV934-N-Q1 LMV931-N, LMV931-N-Q1 LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 www.ti.com SNOS993O – NOVEMBER 2001 – REVISED DECEMBER 2014 Typical Characteristics (continued) Unless otherwise specified, VS = 5 V, single-supply, TA = 25°C. 10 1 INPUT CURRENT NOISE (pA/ Hz) RL = 600: AV = +1 THD (%) 1 0.1 1.8V 0.1 2.7V 5V 0.01 10 100 1k 10k 0.01 10 100k 1k 100 10k 100k FREQUENCY (Hz) FREQUENCY (Hz) Figure 13. Input Current Noise vs. Frequency Figure 14. THD vs. Frequency 10 0.5 RL = 600: AV = +10 SLEW RATE (V/Ps) 0.45 THD (%) 1 5V 0.1 FALLING EDGE 0.4 RISING EDGE 0.35 RL = 2k: 0.3 1.8V AV = +1 2.7V 0.01 10 VIN = 1VPP 0.25 100 1k 10k 0 100k 1 2 5 6 VS = 2.7V RL = 2 k: (50 mV/DIV) INPUT SIGNAL OUTPUT SIGNAL INPUT SIGNAL OUTPUT SIGNAL (50 mV/DIV) RL = 2 k: 4 Figure 16. Slew Rate vs. Supply Voltage Figure 15. THD vs. Frequency VS = 1.8V 3 SUPPLY VOLTAGE (V) FREQUENCY (Hz) TIME (2.5 Ps/DIV) TIME (2.5 Ps/DIV) Figure 17. Small Signal Noninverting Response Figure 18. Small Signal Noninverting Response Copyright © 2001–2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV931-N LMV931-N-Q1 LMV932-N LMV932-N-Q1 LMV934-N LMV934-N-Q1 13 LMV931-N, LMV931-N-Q1 LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 SNOS993O – NOVEMBER 2001 – REVISED DECEMBER 2014 www.ti.com Typical Characteristics (continued) Unless otherwise specified, VS = 5 V, single-supply, TA = 25°C. VIN INPUT SIGNAL VS = 5V OUTPUT SIGNAL (50 mV/DIV) (900 mV/div) RL = 2 k: VOUT VS = 1.8V RL = 2k: AV = +1 TIME (10 Ps/div) TIME (2.5 Ps/DIV) Figure 19. Small Signal Noninverting Response Figure 20. Large Signal Noninverting Response VIN (2.5 V/div) (1.35V/DIV) VIN VOUT VOUT VS = 2.7V VS = 5.0V RL = 2 k: RL = 2k: AV = +1 AV = +1 TIME (10 Ps/div) TIME (10 Ps/DIV) Figure 21. Large Signal Noninverting Response Figure 22. Large Signal Noninverting Response 90 90 SHORT CIRCUIT CURRENT (mA) SHORT CIRCUIT CURRENT (mA) 5V 80 5V 70 60 50 40 2.7V 30 20 1.8V 10 0 -40 10 60 TEMPERATURE (°C) 110 Figure 23. Short Circuit Current vs. Temperature (Sinking) 14 Submit Documentation Feedback 80 70 60 50 40 2.7V 30 20 1.8V 10 0 -40 10 60 TEMPERATURE (°C) 110 Figure 24. Short Circuit Current vs. Temperature (Sourcing) Copyright © 2001–2014, Texas Instruments Incorporated Product Folder Links: LMV931-N LMV931-N-Q1 LMV932-N LMV932-N-Q1 LMV934-N LMV934-N-Q1 LMV931-N, LMV931-N-Q1 LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 www.ti.com SNOS993O – NOVEMBER 2001 – REVISED DECEMBER 2014 Typical Characteristics (continued) Unless otherwise specified, VS = 5 V, single-supply, TA = 25°C. 3 3 VS = 1.8V VS = 2.7V 2.5 2.5 2 2 25°C -40°C 1.5 VOS (mV) VOS (mV) 25°C 1 0.5 85°C 1 0.5 85°C 125°C 125°C 0 0 -0.5 -0.5 -1 -0.4 0 0.4 0.8 -40°C 1.5 1.2 2 1.6 -1 -0.4 2.4 0.1 0.6 VCM (V) 1.1 1.6 2.1 2.6 3.1 VCM (V) Figure 25. Offset Voltage vs. Common-Mode Range Figure 26. Offset Voltage vs. Common-Mode Range 3 VS = 5V 2.5 2 -40°C VOS (mV) 1.5 1 0.5 125°C 25°C 85°C 0 -0.5 -1 -0.4 0.6 1.6 2.6 3.6 4.6 5.6 VCM (V) Figure 27. Offset Voltage vs. Common-Mode Range Copyright © 2001–2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV931-N LMV931-N-Q1 LMV932-N LMV932-N-Q1 LMV934-N LMV934-N-Q1 15 LMV931-N, LMV931-N-Q1 LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 SNOS993O – NOVEMBER 2001 – REVISED DECEMBER 2014 www.ti.com 7 Detailed Description 7.1 Overview The LMV93x-N are low-voltage, low-power operational amplifiers (op-amp) operating from 1.8-V to 5.5-V supply voltages and have rail-to-rail input and output. LMV93x-N input common-mode voltage extends 200 mV beyond the supplies which enables user enhanced functionality beyond the supply voltage range. 7.2 Functional Block Diagram (Each Amplifier) 7.3 Feature Description The differential inputs of the amplifier consist of a noninverting input (+IN) and an inverting input (–IN). The amplifer amplifies only the difference in voltage between the two inputs, which is called the differential input voltage. The output voltage of the op-amp VOUT is given by Equation 1: VOUT = AOL (IN+ - IN-) where • AOL is the open-loop gain of the amplifier, typically around 100 dB (100,000x, or 10 uV per volt). (1) 7.4 Device Functional Modes 7.4.1 Input and Output Stage The rail-to-rail input stage of this family provides more flexibility for the designer. The LMV93x-N use a complimentary PNP and NPN input stage in which the PNP stage senses common-mode voltage near V− and the NPN stage senses common-mode voltage near V+. The transition from the PNP stage to NPN stage occurs 1 V below V+. Because both input stages have their own offset voltage, the offset of the amplifier becomes a function of the input common-mode voltage and has a crossover point at 1 V below V+. Figure 28. Simplified Schematic Diagram 16 Submit Documentation Feedback Copyright © 2001–2014, Texas Instruments Incorporated Product Folder Links: LMV931-N LMV931-N-Q1 LMV932-N LMV932-N-Q1 LMV934-N LMV934-N-Q1 LMV931-N, LMV931-N-Q1 LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 www.ti.com SNOS993O – NOVEMBER 2001 – REVISED DECEMBER 2014 Device Functional Modes (continued) This VOS crossover point can create problems for both DC− and AC-coupled signals if proper care is not taken. Large input signals that include the VOS crossover point will cause distortion in the output signal. One way to avoid such distortion is to keep the signal away from the crossover. For example, in a unity gain buffer configuration with VS = 5 V, a 5-V peak-to-peak signal will contain input-crossover distortion while a 3-V peak-topeak signal centered at 1.5 V will not contain input-crossover distortion as it avoids the crossover point. Another way to avoid large signal distortion is to use a gain of −1 circuit which avoids any voltage excursions at the input terminals of the amplifier. In that circuit, the common-mode DC voltage can be set at a level away from the VOS cross-over point. For small signals, this transition in VOS shows up as a VCM dependent spurious signal in series with the input signal and can effectively degrade small signal parameters such as gain and common-mode rejection ratio. To resolve this problem, the small signal should be placed such that it avoids the VOS crossover point. In addition to the rail-to-rail performance, the output stage can provide enough output current to drive 600Ω loads. Because of the high-current capability, take care not to exceed the 150°C maximum junction temperature specification. 7.4.2 Input Bias Current Consideration The LMV93x-N family has a complementary bipolar input stage. The typical input bias current (IB) is 15 nA. The input bias current can develop a significant offset voltage. This offset is primarily due to IB flowing through the negative feedback resistor, RF. For example, if IB is 50 nA and RF is 100 kΩ, then an offset voltage of 5 mV will develop (VOS = IB x RF). Using a compensation resistor (RC), as shown in Figure 29, cancels this effect. But the input offset current (IOS) will still contribute to an offset voltage in the same manner. Figure 29. Canceling the Offset Voltage due to Input Bias Current Copyright © 2001–2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV931-N LMV931-N-Q1 LMV932-N LMV932-N-Q1 LMV934-N LMV934-N-Q1 17 LMV931-N, LMV931-N-Q1 LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 SNOS993O – NOVEMBER 2001 – REVISED DECEMBER 2014 www.ti.com 8 Application and Implementation NOTE Information in the following applications sections is not part of the TI component specification, and TI does not warrant its accuracy or completeness. TI’s customers are responsible for determining suitability of components for their purposes. Customers should validate and test their design implementation to confirm system functionality. 8.1 Application Information The LMV93x-N devices bring performance, economy and ease-of-use to low-voltage, low-power systems. They provide rail-to-rail input and rail-to-rail output swings into heavy loads. 8.2 Typical Applications 8.2.1 High-Side Current-Sensing Application Figure 30. High-Side Current Sensing 8.2.1.1 Design Requirements The high-side current-sensing circuit (Figure 30) is commonly used in a battery charger to monitor charging current to prevent overcharging. A sense resistor RSENSE is connected to the battery directly. This system requires an op amp with rail-to-rail input. The LMV93x-N are ideal for this application because its common-mode input range extends up to the positive supply. 8.2.1.2 Detailed Design Procedure As seen in Figure 30, the ICHARGE current flowing through sense resistor RSENSE develops a voltage drop equal to VSENSE. The voltage at the negative sense point will now be less than the positive sense point by an amount proportional to the VSENSE voltage. The low-bias currents of the LMV93x cause little voltage drop through R2, so the negative input of the LMV93x amplifier is at essentially the same potential as the negative sense input. The LMV93x will detect this voltage error between its inputs and servo the transistor base to conduct more current through Q1, increasing the voltage drop across R1 until the LMV93x inverting input matches the noninverting input. At this point, the voltage drop across R1 now matches VSENSE. IG, a current proportional to ICHARGE, will flow according to the following relation: IG = VRSENSE / R1 = ( RSENSE * ICHARGE ) / R1 (2) IG also flows through the gain resistor R3 developing a voltage drop equal to: V3 = IG * R3 = ( VRSENSE / R1 ) * R3 = ( ( RSENSE * ICHARGE ) / R2 ) * R3 18 Submit Documentation Feedback (3) Copyright © 2001–2014, Texas Instruments Incorporated Product Folder Links: LMV931-N LMV931-N-Q1 LMV932-N LMV932-N-Q1 LMV934-N LMV934-N-Q1 LMV931-N, LMV931-N-Q1 LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 www.ti.com SNOS993O – NOVEMBER 2001 – REVISED DECEMBER 2014 Typical Applications (continued) VOUT = (RSENSE * ICHARGE ) * G where • G = R3 / R1 (4) The other channel of the LMV93x may be used to buffer the voltage across R3 to drive the following stages. 8.2.1.3 Application Curve Figure 31 shows the results of the example current sense circuit. 5 VOUT (V) 4 3 2 1 0 0 1 2 3 4 5 ICHARGE (A) C001 NOTE: the error after 4 V where transistor Q1 runs out of headroom and saturates, limiting the upper output swing. Figure 31. Current Sense Amplifier Results 8.2.2 Half-Wave Rectifier Applications RI VIN VOUT RI VIN VCC 3 VOUT LMV931 4 + 0 t 1 t Figure 32. Half-Wave Rectifier With Rail-To-Ground Output Swing Referenced to Ground VCC VIN VOUT 3 + VCC 4 VIN VCC t VOUT LMV931 RI 1 t RI Figure 33. Half-Wave Rectifier With Negative-Going Output Referenced to VCC Copyright © 2001–2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV931-N LMV931-N-Q1 LMV932-N LMV932-N-Q1 LMV934-N LMV934-N-Q1 19 LMV931-N, LMV931-N-Q1 LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 SNOS993O – NOVEMBER 2001 – REVISED DECEMBER 2014 www.ti.com Typical Applications (continued) 8.2.2.1 Design Requirements Because the LMV931-N, LMV932-N, LMV934-N input common-mode range includes both positive and negative supply rails and the output can also swing to either supply, achieving half-wave rectifier functions in either direction is an easy task. All that is needed are two external resistors; there is no need for diodes or matched resistors. The half-wave rectifier can have either positive or negative going outputs, depending on the way the circuit is arranged. 8.2.2.2 Detailed Design Procedure In Figure 32 the circuit is referenced to ground, while in Figure 33 the circuit is biased to the positive supply. These configurations implement the half-wave rectifier because the LMV93x-N can not respond to one-half of the incoming waveform. It can not respond to one-half of the incoming because the amplifier cannot swing the output beyond either rail therefore the output disengages during this half cycle. During the other half cycle, however, the amplifier achieves a half wave that can have a peak equal to the total supply voltage. RI should be large enough not to load the LMV93x-N. 8.2.2.3 Application Curve Figure 34. Output of Ground-to-Rail Circuit Figure 35. Output of Rail-to-Ground Circuit 8.2.3 Instrumentation Amplifier With Rail-to-Rail Input and Output Application Figure 36. Rail-to-Rail Instrumentation Amplifier 8.2.3.1 Design Requirements Using three of the LMV93x-N amplifiers, an instrumentation amplifier with rail-to-rail inputs and outputs can be made as shown in Figure 36. 8.2.3.2 Detailed Design Procedure In this example, amplifiers on the left side act as buffers to the differential stage. These buffers assure that the input impedance is very high. They also assure that the difference amp is driven from a voltage source. This is necessary to maintain the CMRR set by the matching R1-R2 with R3-R4. The gain is set by the ratio of R2/R1 and R3 should equal R1 and R4 equal R2. With both rail-to-rail input and output ranges, the input and output are only limited by the supply voltages. Remember that even with rail-to-rail outputs, the output can not swing past the supplies so the combined common-mode voltages plus the signal should not be greater that the supplies or limiting will occur. 8.2.3.3 Application Curve Figure 37 shows the results of the instrumentation amplifier with R1 and R3 = 1 K, and R2 and R4 = 100 kΩ, for a gain of 100, running on a single 5-V supply with a input of VCM = VS/2. The combined effects of the individual offset voltages can be seen as a shift in the offset of the curve. 20 Submit Documentation Feedback Copyright © 2001–2014, Texas Instruments Incorporated Product Folder Links: LMV931-N LMV931-N-Q1 LMV932-N LMV932-N-Q1 LMV934-N LMV934-N-Q1 LMV931-N, LMV931-N-Q1 LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 www.ti.com SNOS993O – NOVEMBER 2001 – REVISED DECEMBER 2014 Typical Applications (continued) 5 VOUT (V) 4 3 2 1 0 0 10 20 30 VDIFF (mV) 40 50 C001 Figure 37. Instrumentation Amplifier Output Results 8.3 Dos and Don'ts Do properly bypass the power supplies. Do add series resistence to the output when driving capacitive loads, particularly cables, Muxes and ADC inputs. Do add series current limiting resistors and external schottky clamp diodes if input voltage is expected to exceed the supplies. Limit the current to 1 mA or less (1 kΩ per volt). 9 Power Supply Recommendations For proper operation, the power supplies must be properly decoupled. For decoupling the supply lines, TI recommends that 10-nF capacitors be placed as close as possible to the op amp power supply pins. For singlesupply, place a capacitor between V+ and V− supply leads. For dual supplies, place one capacitor between V+ and ground, and one capacitor between V- and ground. 10 Layout 10.1 Layout Guidelines The V+ pin should be bypassed to ground with a low-ESR capacitor. The optimum placement is closest to the V+ and ground pins. Take care to minimize the loop area formed by the bypass capacitor connection between V+ and ground. The ground pin should be connected to the PCB ground plane at the pin of the device. The feedback components should be placed as close to the device as possible minimizing strays. Copyright © 2001–2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV931-N LMV931-N-Q1 LMV932-N LMV932-N-Q1 LMV934-N LMV934-N-Q1 21 LMV931-N, LMV931-N-Q1 LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 SNOS993O – NOVEMBER 2001 – REVISED DECEMBER 2014 www.ti.com 10.2 Layout Example Figure 38. SOT-23 Layout Example 22 Submit Documentation Feedback Copyright © 2001–2014, Texas Instruments Incorporated Product Folder Links: LMV931-N LMV931-N-Q1 LMV932-N LMV932-N-Q1 LMV934-N LMV934-N-Q1 LMV931-N, LMV931-N-Q1 LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 www.ti.com SNOS993O – NOVEMBER 2001 – REVISED DECEMBER 2014 11 Device and Documentation Support 11.1 Device Support 11.1.1 Development Support LMV931 PSPICE Model (also applicable to the LMV932 and LMV934), http://www.ti.com/lit/zip/snom028 TINA-TI SPICE-Based Analog Simulation Program, http://www.ti.com/tool/tina-ti DIP Adapter Evaluation Module, http://www.ti.com/tool/dip-adapter-evm TI Universal Operational Amplifier Evaluation Module, http://www.ti.com/tool/opampevm TI Filterpro Software, http://www.ti.com/tool/filterpro 11.2 Documentation Support 11.2.1 Related Documentation For additional applications, see the following: AN-31 Op Amp Circuit Collection, SNLA140 11.3 Related Links The table below lists quick access links. Categories include technical documents, support and community resources, tools and software, and quick access to sample or buy. Table 1. Related Links PARTS PRODUCT FOLDER SAMPLE & BUY TECHNICAL DOCUMENTS TOOLS & SOFTWARE SUPPORT & COMMUNITY LMV931-N Click here Click here Click here Click here Click here LMV931-N-Q1 Click here Click here Click here Click here Click here LMV932-N Click here Click here Click here Click here Click here LMV932-N-Q1 Click here Click here Click here Click here Click here LMV934-N Click here Click here Click here Click here Click here LMV934-N-Q1 Click here Click here Click here Click here Click here 11.4 Trademarks All trademarks are the property of their respective owners. 11.5 Electrostatic Discharge Caution These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam during storage or handling to prevent electrostatic damage to the MOS gates. 11.6 Glossary SLYZ022 — TI Glossary. This glossary lists and explains terms, acronyms, and definitions. 12 Mechanical, Packaging, and Orderable Information The following pages include mechanical, packaging, and orderable information. This information is the most current data available for the designated devices. This data is subject to change without notice and revision of this document. For browser-based versions of this data sheet, refer to the left-hand navigation. Copyright © 2001–2014, Texas Instruments Incorporated Submit Documentation Feedback Product Folder Links: LMV931-N LMV931-N-Q1 LMV932-N LMV932-N-Q1 LMV934-N LMV934-N-Q1 23 PACKAGE OPTION ADDENDUM www.ti.com 27-Jun-2015 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking (4/5) LMV931MF NRND SOT-23 DBV 5 1000 TBD Call TI Call TI -40 to 125 A79A LMV931MF/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 A79A LMV931MFX NRND SOT-23 DBV 5 3000 TBD Call TI Call TI -40 to 125 A79A LMV931MFX/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 A79A LMV931MG NRND SC70 DCK 5 1000 TBD Call TI Call TI -40 to 125 A74 LMV931MG/NOPB ACTIVE SC70 DCK 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 A74 LMV931MGX/NOPB ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 A74 LMV931Q1MF/NOPB ACTIVE SOT-23 DBV 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 ALAA LMV931Q1MFX/NOPB ACTIVE SOT-23 DBV 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 ALAA LMV931Q1MG/NOPB ACTIVE SC70 DCK 5 1000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 BBA LMV931Q1MGX/NOPB ACTIVE SC70 DCK 5 3000 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 BBA LMV932MA NRND SOIC D 8 95 TBD Call TI Call TI -40 to 125 LMV9 32MA LMV932MA/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LMV9 32MA LMV932MAX NRND SOIC D 8 2500 TBD Call TI Call TI -40 to 125 LMV9 32MA LMV932MAX/NOPB ACTIVE SOIC D 8 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LMV9 32MA TBD Call TI Call TI LMV932MM NRND VSSOP DGK 8 1000 -40 to 125 A86A LMV932MM/NOPB ACTIVE VSSOP DGK 8 1000 Green (RoHS CU NIPDAUAG | CU SN Level-1-260C-UNLIM & no Sb/Br) -40 to 125 A86A LMV932MMX/NOPB ACTIVE VSSOP DGK 8 3500 Green (RoHS CU NIPDAUAG | CU SN Level-1-260C-UNLIM & no Sb/Br) -40 to 125 A86A LMV932Q1MA/NOPB ACTIVE SOIC D 8 95 Green (RoHS & no Sb/Br) -40 to 125 LMV93 2Q1MA Addendum-Page 1 CU SN Level-1-260C-UNLIM Samples PACKAGE OPTION ADDENDUM www.ti.com 27-Jun-2015 Orderable Device Status (1) LMV932Q1MAX/NOPB Package Type Package Pins Package Drawing Qty Eco Plan Lead/Ball Finish MSL Peak Temp (2) (6) (3) Op Temp (°C) Device Marking Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LMV93 2Q1MA (4/5) ACTIVE SOIC D 8 2500 LMV934MA NRND SOIC D 14 55 TBD Call TI Call TI -40 to 125 LMV934MA LMV934MA/NOPB ACTIVE SOIC D 14 55 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LMV934MA LMV934MAX NRND SOIC D 14 2500 TBD Call TI Call TI -40 to 125 LMV934MA LMV934MAX/NOPB ACTIVE SOIC D 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LMV934MA LMV934MT/NOPB ACTIVE TSSOP PW 14 94 Green (RoHS & no Sb/Br) CU NIPDAU | CU SN Level-1-260C-UNLIM -40 to 125 LMV93 4MT LMV934MTX NRND TSSOP PW 14 2500 TBD Call TI Call TI -40 to 125 LMV93 4MT LMV934MTX/NOPB ACTIVE TSSOP PW 14 2500 Green (RoHS & no Sb/Br) CU NIPDAU | CU SN Level-1-260C-UNLIM -40 to 125 LMV93 4MT LMV934Q1MT/NOPB ACTIVE TSSOP PW 14 94 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LMV934 Q1MT LMV934Q1MTX/NOPB ACTIVE TSSOP PW 14 2500 Green (RoHS & no Sb/Br) CU SN Level-1-260C-UNLIM -40 to 125 LMV934 Q1MT (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Addendum-Page 2 Samples PACKAGE OPTION ADDENDUM www.ti.com (4) 27-Jun-2015 There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device. (5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation of the previous line and the two combined represent the entire Device Marking for that device. (6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish value exceeds the maximum column width. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. OTHER QUALIFIED VERSIONS OF LMV931-N, LMV931-N-Q1, LMV932-N, LMV932-N-Q1, LMV934-N, LMV934-N-Q1 : • Catalog: LMV931-N, LMV932-N, LMV934-N • Automotive: LMV931-N-Q1, LMV932-N-Q1, LMV934-N-Q1 NOTE: Qualified Version Definitions: • Catalog - TI's standard catalog product • Automotive - Q100 devices qualified for high-reliability automotive applications targeting zero defects Addendum-Page 3 PACKAGE MATERIALS INFORMATION www.ti.com 14-Mar-2015 TAPE AND REEL INFORMATION *All dimensions are nominal Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) LMV931MF SOT-23 DBV 5 1000 178.0 8.4 LMV931MF/NOPB SOT-23 DBV 5 1000 178.0 LMV931MFX SOT-23 DBV 5 3000 178.0 LMV931MFX/NOPB SOT-23 DBV 5 3000 LMV931MG SC70 DCK 5 W Pin1 (mm) Quadrant 3.2 3.2 1.4 4.0 8.0 Q3 8.4 3.2 3.2 1.4 4.0 8.0 Q3 8.4 3.2 3.2 1.4 4.0 8.0 Q3 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 1000 178.0 8.4 2.25 2.45 1.2 4.0 8.0 Q3 LMV931MG/NOPB SC70 DCK 5 1000 178.0 8.4 2.25 2.45 1.2 4.0 8.0 Q3 LMV931MGX/NOPB SC70 DCK 5 3000 178.0 8.4 2.25 2.45 1.2 4.0 8.0 Q3 LMV931Q1MF/NOPB SOT-23 DBV 5 1000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LMV931Q1MFX/NOPB SOT-23 DBV 5 3000 178.0 8.4 3.2 3.2 1.4 4.0 8.0 Q3 LMV931Q1MG/NOPB SC70 DCK 5 1000 178.0 8.4 2.25 2.45 1.2 4.0 8.0 Q3 LMV931Q1MGX/NOPB SC70 DCK 5 3000 178.0 8.4 2.25 2.45 1.2 4.0 8.0 Q3 LMV932MAX SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LMV932MAX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LMV932MM VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LMV932MM/NOPB VSSOP DGK 8 1000 178.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LMV932MMX/NOPB VSSOP DGK 8 3500 330.0 12.4 5.3 3.4 1.4 8.0 12.0 Q1 LMV932Q1MAX/NOPB SOIC D 8 2500 330.0 12.4 6.5 5.4 2.0 8.0 12.0 Q1 LMV934MAX SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1 Pack Materials-Page 1 PACKAGE MATERIALS INFORMATION www.ti.com 14-Mar-2015 Device Package Package Pins Type Drawing SPQ Reel Reel A0 Diameter Width (mm) (mm) W1 (mm) B0 (mm) K0 (mm) P1 (mm) W Pin1 (mm) Quadrant LMV934MAX/NOPB SOIC D 14 2500 330.0 16.4 6.5 9.35 2.3 8.0 16.0 Q1 LMV934MTX TSSOP PW 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 LMV934MTX/NOPB TSSOP PW 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 LMV934MTX/NOPB TSSOP PW 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 LMV934Q1MTX/NOPB TSSOP PW 14 2500 330.0 12.4 6.95 8.3 1.6 8.0 12.0 Q1 *All dimensions are nominal Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LMV931MF SOT-23 DBV 5 1000 210.0 185.0 35.0 LMV931MF/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LMV931MFX SOT-23 DBV 5 3000 210.0 185.0 35.0 LMV931MFX/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LMV931MG SC70 DCK 5 1000 210.0 185.0 35.0 LMV931MG/NOPB SC70 DCK 5 1000 210.0 185.0 35.0 LMV931MGX/NOPB SC70 DCK 5 3000 210.0 185.0 35.0 LMV931Q1MF/NOPB SOT-23 DBV 5 1000 210.0 185.0 35.0 LMV931Q1MFX/NOPB SOT-23 DBV 5 3000 210.0 185.0 35.0 LMV931Q1MG/NOPB SC70 DCK 5 1000 210.0 185.0 35.0 LMV931Q1MGX/NOPB SC70 DCK 5 3000 210.0 185.0 35.0 LMV932MAX SOIC D 8 2500 367.0 367.0 35.0 Pack Materials-Page 2 PACKAGE MATERIALS INFORMATION www.ti.com 14-Mar-2015 Device Package Type Package Drawing Pins SPQ Length (mm) Width (mm) Height (mm) LMV932MAX/NOPB SOIC D 8 2500 367.0 367.0 35.0 LMV932MM VSSOP DGK 8 1000 210.0 185.0 35.0 LMV932MM/NOPB VSSOP DGK 8 1000 210.0 185.0 35.0 LMV932MMX/NOPB VSSOP DGK 8 3500 367.0 367.0 35.0 LMV932Q1MAX/NOPB SOIC D 8 2500 367.0 367.0 35.0 LMV934MAX SOIC D 14 2500 367.0 367.0 35.0 LMV934MAX/NOPB SOIC D 14 2500 367.0 367.0 35.0 LMV934MTX TSSOP PW 14 2500 367.0 367.0 35.0 LMV934MTX/NOPB TSSOP PW 14 2500 367.0 367.0 35.0 LMV934MTX/NOPB TSSOP PW 14 2500 367.0 367.0 35.0 LMV934Q1MTX/NOPB TSSOP PW 14 2500 367.0 367.0 35.0 Pack Materials-Page 3 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily performed. TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use of any TI components in safety-critical applications. In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and requirements. Nonetheless, such components are subject to these terms. No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties have executed a special agreement specifically governing such use. Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of non-designated products, TI will not be responsible for any failure to meet ISO/TS16949. Products Applications Audio www.ti.com/audio Automotive and Transportation www.ti.com/automotive Amplifiers amplifier.ti.com Communications and Telecom www.ti.com/communications Data Converters dataconverter.ti.com Computers and Peripherals www.ti.com/computers DLP® Products www.dlp.com Consumer Electronics www.ti.com/consumer-apps DSP dsp.ti.com Energy and Lighting www.ti.com/energy Clocks and Timers www.ti.com/clocks Industrial www.ti.com/industrial Interface interface.ti.com Medical www.ti.com/medical Logic logic.ti.com Security www.ti.com/security Power Mgmt power.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Microcontrollers microcontroller.ti.com Video and Imaging www.ti.com/video RFID www.ti-rfid.com OMAP Applications Processors www.ti.com/omap TI E2E Community e2e.ti.com Wireless Connectivity www.ti.com/wirelessconnectivity Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2015, Texas Instruments Incorporated