RoHS BR3505-3510 SINGLE-PHASE BRIDGE RECTIFIER FEATURES Low cost This series is UL recognized under component index, file number E127707 High forward surge current capability Integrally molded heatsink provide very low thermal resistance. High isolation voltage from case to lugs High temperature soldering guaranteed: 260/10 second, at 5 lbs. (2.3kg) tension. MECHANICAL DATA Case: Molded plastic body, Suffix "N" for thinner type. Terminal: Plated 0.25" (6.35mm) lug. Polarity: Polarity symbols marked on case. Mounting: Thru hole for #10 screw, 20 in,- lbs. Torqute Max. Weight: 0.66 ounce, 18.7gram(BR35) O MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 ambient temperature unless otherwise specified Single phase, half wave, 60Hz, resistive or inductive load. For capacitive load derate current by 20% C E L Maximum Repetitive Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Rectified Output Current, at TC = 50 (Note 1) Peak Forward Surge Current 8.3ms single half sine - wave superimposed on rated load (JEDEC method ) Rating for Fusing (t<8.3ms) J E R T E Maximum Instantaneous Forward Voltage Drop per bridge element at 17.5A Maximum DC Reverse Current at rated TA = 25 DC blocking voltage per element TA Isolation Voltage from case to lugs. Typical Thermal Resistance (Note 1,2) Operating Temperature Range Storage Temperature Range W IC C D T ,. L O N SYMBOLSBR3505 BR351 BR352 BR354 BR356 BR358 BR3510 VRRM VRMS VDC UNIT Volts Volts Volts I(AV) Amps IFSM Amps It 2 As VF Volts 2.0 (-65 to +150) (-65 to +150) A mA VAC /W IR VISO R TJ TSTG 2 1. Unit mounted on 9" X 3.5" X 4.6" (23cm X 9cm X 11.8cm)Al. finned Plate. 2. Bolt down on heat-sink with silicon thermal compound between bridge and mounting sutfae for maximum heat transfer efficiency with # 10 screw. WEJ ELECTRONIC CO. Http:// www.wej.cn E-mail:[email protected] RoHS BR3505-3510 FIG.1-DERATING CURVE FOR FIG.2-MAXIMUM NON-REPETITIVE PEAK OUTPUT RECTIFIED CURRENT FORWARD SURGE CURRENT PER ELEMENT 35 700 (23 X 9 X 11.8cm) AL.Finned Plate Single Phase Half Wave 60Hz 10 Inductive or Resistive 1 Cycle 400 300 200 100 Load 0 1 0 0 25 75 50 100 125 150 Tj =25 ° C Pulse Width=300uS 1%Duty Cycle R T 0.1 C E L 1.2 1.4 1.6 INSTANTANEOUS FORWARD VOLTAGE,(V) INSTANTANEOUS REVERSE CURRENT, 1.0 1.0 40 60 100 CHARACTERISTICS IC Tj =100 ° C N O 10 (uA) 10 (A) C 100 0.8 20 PER BRIDGE ELEMENT 100 0.6 8 10 FIG.4-TYPICAL REVERSE PER BRIDGE ELEMENT INSTANTANEOUS FORWARD CURRENT, 6 j max NUMBER OF CYCLES AT 60 Hz FIG.3-TYPICAL FORWARD CHARACTERISTICS 0.4 4 2 175 CASE TEMPERATURE, ( ° C) 0.01 D T ,. L O 8.3ms Single Half Sine-Wave Tj (JEDEC Method) =T 500 CURRENT, (A) 9"X 3.5"X 4.6" Thick 20 600 PEAK FORWARD SURGE Heat Sink Mounting CURRENT,(A) AVERAGE FORWARD OUTPUT 30 1.0 Tj =25 ° C 0.1 0.01 1.8 60 40 20 0 100 80 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE,(%) FIG.5-TYPICAL JUNCTION CAPACITANCE FIG.6-MAXIMUM POWER DISSIPATION E PER BRIDGE ELEMENT W T j=25 ° C f=1MHz V sig =50mV p-p 10 0.1 1.0 10 100 REVRESE VOLTAGE,(V) WEJ ELECTRONIC CO. Http:// www.wej.cn 80 (W) JUNCTION CAPACITANCE,(pF) J E 100 100 AVERAGE POWER DISSIPATION OF BRIDGE, 1000 Tj =T j max 60 Capacitive Load 40 Resistive or Inductive 20 Load 0 0 5 10 15 20 25 30 35 AVERAGE OUTPUT CURRENT, (A) E-mail:[email protected]