IS-1845ASRH ® Data Sheet October 2003 Single Event Radiation Hardened High Speed, Current Mode PWM FN9001.3 Features • Electrically Screened to DSCC SMD # 5962-01509 The IS-1845ASRH is designed to be used in switching power supplies operating in current-mode. The rising edge of the on-chip oscillator turns on the output. Turn-off is controlled by the current sense comparator and occurs when the sensed current reaches a peak controlled by the error amplifier. TM Constructed with Intersil’s Rad Hard Silicon Gate (RSG) dielectrically isolated BiCMOS process, these devices are immune to single event latch-up and have been specifically designed to provide a high level of immunity to single event transients. All specified parameters are guaranteed and tested for 300krad(Si) total dose performance. • QML Qualified per MIL-PRF-38535 Requirements • Radiation Environment - Total Dose . . . . . . . . . . . . . . . . . . . . 300 krad(SI) (Max) - SEL Immune. . . . . . . . . . . . . . . . . Dielectrically Isolated - SEU Immune . . . . . . . . . . . . . . . . . . . . 35MeV/mg/cm2 - SEU Cross-Section at 89MeV/mg/cm2 . . . . 5 x 10-6cm2 • Low Start-up Current . . . . . . . . . . . . . . . . . . . 100µA (Typ) • Fast Propagation Delay . . . . . . . . . . . . . . . . . . 80ns (Typ) • Supply Voltage Range . . . . . . . . . . . . . . . . . . . 12V to 20V • High Output Drive. . . . . . . . . . . . . . . . . . . . 1A (Peak, Typ) • Under Voltage Lockout. .8.8V Start (Typ), 8.2V Stop (Typ) Detailed Electrical Specifications for these devices are contained in SMD 5962-01509. A “hot-link” is provided on our website for downloading the SMD. Applications Pinouts • Control of High Current FET Drivers IS7-1845ASRH (CDIP2-T8 SBDIP) TOP VIEW COMP 1 8 VREF VFB 2 7 VCC ISENSE 3 6 OUT RTCT 4 5 GND • Current-Mode Switching Power Supplies • Motor Speed and Direction Control Ordering Information ORDERING NUMBER IS9-1845ASRH (FLATPACK) TOP VIEW NC 1 18 NC COMP 2 17 VREF VFB 3 16 VCC NC 4 15 VC NC 5 14 OUT NC 6 13 NC ISENSE 7 12 GND RTCT 8 11 OSCGND NC 9 10 NC INTERNAL MKT. NUMBER TEMP. RANGE (oC) 5962F0150901VPC IS7-1845ASRH-Q -50 to 125 5962F0150901QPC IS7-1845ASRH-8 -50 to 125 5962F0150901VXC IS9-1845ASRH-Q -50 to 125 5962F0150901QXC IS9-1845ASRH-8 -50 to 125 IS7-1845ASRH/Proto IS1-1845ASRH/Proto -50 to 125 IS9-1845ASRH/Proto IS9-1845ASRH/Proto -50 to 125 NOTES: 1. Grounding the Comp pin does not inhibit the output. The output may be inhibited by applying >1.2V to the ISENSE pin. 2. This part should be operated with CT=3.3nF and RT=10k timing components only. 1 CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures. 1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc. Copyright © Intersil Americas Inc. 2003. All Rights Reserved. All other trademarks mentioned are the property of their respective owners. IS-1845ASRH Die Characteristics Substrate Radiation Hardened Silicon Gate, Dielectric Isolation DIE DIMENSIONS 3090µm x 4080µm (121.6 mils x 159.0 mils) Thickness: 483µm ± 25.4µm (19 mils ± 1 mil) Backside Finish Silicon INTERFACE MATERIALS ASSEMBLY RELATED INFORMATION Glassivation Substrate Potential Type: Phosphorus Silicon Glass (PSG) Thickness: 8.0kA ± 1.0kA Unbiased (DI) Top Metallization ADDITIONAL INFORMATION Type: AlSiCu Thickness: 16.0kA ± 2kA Worst Case Current Density <2.0 x 105 A/cm2 Transistor Count 582 Metallization Mask Layout IS-1845ASRH VFB ISENSE COMP RTCT OSCGND VREF GND GND OUT VC VCC NOTES: 3. Both the GND pads must be bonded to ground. 4. The OUT double-sized bond pad must be double bonded for current sharing purposes. 5. The OSCGND double-sized bond pad must be double bonded to ground for current sharing purposes. All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems. Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries. For information regarding Intersil Corporation and its products, see www.intersil.com 2