MADR-008888-000100 PIN Diode Driver for Series / Series High Power Switch Pin Configuration Features Rev. 5 High Drive Current Capability (± 50 mA) 27V Back Bias in Off State Switching Speed Approximately 1.5 µs Low Current Consumption Land Grid Array Package for SMT Applications Tape and Reel Packaging Available Lead-Free Package 260°C Reflow Compatible RoHS* Compliant Single CMOS Logic input Pin No. Pin Name Pin No. Pin Name 1 VCC (+5V) 13 GND 2 GND 14 NC 3 C1 (Logic) 15 GND 4 GND 16 TX Drive 5 VDD (+28V) 17 GND 6 GND 18 GND 7 GND 19 GND 8 GND 20 GND 9 GND 21 GND 10 RX Drive 22 GND 11 GND 23 GND 12 NC - - Description M/A-COM Technology Solutions MADR-008888000100 Switch Driver is designed to work with M/ACOM Tech switch MASW-000823-12770T or other series / series switches. This driver is design to provide currents up to 50 mA for each diode in series / series switches. It is designed for SPDT switches that operate with a power range of approximately 5 – 20W CW. The driver is packaged in a Land Grid Array surface mount package and is available in tape and reel packaging for high volume applications. The MADR-008888-000100 driver is ideally suited for driving M/A-COM’s line of HMIC switches. Absolute Maximum Ratings 2,3 Note that this driver will also operate when VDD is set to voltages other than +28V. It could also operate at +12V, +15V, +20V, and +24V supplies. Ordering Information 1 Parameter Absolute Maximum VCC (+5V) -0.5V to +6.5V VDD (+28V) -0.5V to 40V C1 (Logic) -0.5V to 6.5 V RX Drive Current 60 mA TX Drive Current 60 mA Power Dissipation in Still Air 100 mW Part Number Package Operational Temperature -40 to +85°C MADR-008888-000100 Bulk Packaging Storage Temperature -55 to +125°C MADR-008888-0001TR 300 piece Reel MADR-008888-0001TB Sample Board with Driver & MASW-000822-12770T Switch MADR-008888-0002TB Sample Board with Driver & MASW-000825-12770T Switch Truth Table (Switch) Condition of Switch Control Input 1. Reference Application Note M513 for reel size information. 2. Exceeding any one or combination of these limits may cause permanent damage to this device. 3. M/A-COM does not recommend sustained operation near these survivability limits. RF Common to Each RF Port C1 TX RX 0 Off On 1 On Off * Restrictions on Hazardous Substances, European Union Directive 2002/95/EC. 1 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, • India Tel: +91.80.43537383 • China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MADR-008888-000100 PIN Diode Driver for Series / Series High Power Switch Rev. 5 Electrical Specifications: TA = +25C, +VCC = +5.0 V, VDD = +28 V Parameter Test Conditions Unit Min Typ Max Assumes 1V Drop on PIN Diode Assumes 1V Drop on PIN Diode mA mA — — 22 or 35 22 or 35 50 50 RX ON TX ON V V — — 27 27 — — Switching Speed: ANT-TX5 Ton Toff Trise Tfall 50% CTL to 90% Voltage 50% CTL to 10% Voltage 10% - 90% 90% - 10% µs µs ns ns — — — — 0.9 1.5 250 300 2.06 2.06 — — Switching Speed: ANT-RX5 Ton Toff Trise Tfall 50% CTL to 90% Voltage 50% CTL to 10% Voltage 10% - 90% 90% - 10% µs µs ns ns — — — — 1.5 0.9 200 250 2.06 2.06 — — 50% duty cycle KHz DC — 50 VCC (+5V) VDD (+28V) mA mA — — — — 0.1 5.0 Logic “0” @ 20 µA sink current Logic “1” @ 0.5 mA source current V V 0.0 3.5 0.0 5.0 1.5 5.0 R1 = 80 Ω R1 = 110 Ω R1 = 180 Ω R1 = N/A mA mA mA mA — — — — 51 36 23 2.5 — — — — DC Output Current RX Current 4 TX Current 4 Back Bias Voltage on TX Diode RX Diode PRF Quiescent Supply Currents Logic Levels Supply Currents4 ICC IDD 4. 5. 6. Currents are user selectable. Reference “Driver and SPDT Schematic” for suggested values. R1 should be ≥ 80 ohms for VCC= 5.0V. R1 should be ≥ 65 ohms for VCC = 3.3V. Switch parameters were measured when driving the MASW-000823-12770T switch. Maximums are for load currents up to 25mA Recommended Operating Conditions Parameter Test Conditions Unit Min Typ Max VCC Nominal VCC = 3.3 V Nominal VCC = 5.0 V V V 3.0 4.5 3.3 5.0 3.6 5.5 VDD Input Voltage V 27.0 28.0 29.0 C1 (Low Level Input Voltage) VCC = 3.0 V to 3.6V VCC = 4.5 V to 5.5 V V V 0.0 0.0 0.0 0.0 0.8 0.3 x VCC C1 (High Level Input Voltage) VCC = 3.0 V to 3.6V VCC = 4.5 V to 5.5 V V V 2 0.7 x VCC VCC VCC VCC VCC Handling Procedures Please observe the following precautions to avoid damage: Static Sensitivity Silicon Circuits are sensitive to electrostatic discharge (ESD) and can be damaged by static electricity. Proper ESD control techniques should be used when handling these devices. 2 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, • India Tel: +91.80.43537383 • China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MADR-008888-000100 PIN Diode Driver for Series / Series High Power Switch Rev. 5 Typical Performance Curves TX On, 50 mA Load Current -40ºC 5 +25ºC 4 +85ºC 3 2 1 0 -0.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 Switching Waveform Ton Switching Waveform Ton TX On, 20 mA Load Current +25ºC -40ºC 5 4 +85ºC 3 2 1 0 -0.5 0.0 0.5 1.0 1.5 Time (µs) +25ºC 2 +85ºC -40ºC 0 -0.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 Switching Waveform Ton Switching Waveform Ton 4 3 Switching Waveform Ton Switching Waveform Ton +25ºC 4 +85ºC 2 1 0 -0.5 0.0 0.5 1.0 1.5 2.0 2.5 -0.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 -40ºC +25ºC +85ºC 0 -0.5 0.0 0.5 1.0 1.5 2.0 2.5 Time (µs) 3.0 3.5 4.0 4.5 Switching Waveform Ton 4 1 4.5 4 +85ºC 3 2 1 0 -0.5 0.0 0.5 1.0 1.5 2.0 2.5 RX Off, 50 mA Load Current 5 3.0 +25ºC 5 RX Off, 20 mA Load Current -40ºC 4.0 0 Time (µs) 2 3.5 +85ºC -40ºC 1 Time (us) 3 4.5 +25ºC RX On, 50 mA Load Current 3 4.0 2 RX On, 20 mA Load Current -40ºC 3.5 4 Time (µs) 5 3.0 5 Time (µs) Switching Waveform Ton 3 5 1 2.5 TX Off, 50 mA Load Current TX Off, 20 mA Load Current 3 2.0 Time (µs) 3.0 3.5 4.0 4.5 5 4 3 +25ºC 2 -40ºC +85ºC 1 0 -0.5 0.0 0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5 Time (µs) ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, • India Tel: +91.80.43537383 • China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MADR-008888-000100 PIN Diode Driver for Series / Series High Power Switch Rev. 5 Driver and SPDT Schematic with +5V & +28V DC Power 7,8,9,10,11,12,13,14 ANT C3 100 pF R1 See Note 8 L1 27 nH +5V C4 100 pF C5 100 pF TX RX C1 100 pF 100V +28V +5V MADR-008888-000100 Switch Driver L2 27 nH L3 27 nH SPDT Cbypass 12 pF C2 100 pF 100V Cbypass 12 pF Logic Input Ground 7. 8. 9. 10. 11. 12. 13. 14. Forward Bias Diode Voltage: Vf is 0.9V @ 22 mA; Vf is 1.0V @ 35 mA For 22 mA load current, R1 = 180 Ω @ VCC = 5.0V and 105 Ω @ VCC = 3.3V. For 35 mA load current, R1 = 110 Ω @ VCC = 5.0V and 165 Ω @ VCC= 3.3V. Nominal power dissipation in the 180 Ω and 110 Ω resistors are 87 mW and 135 mW. Reverse Bias is ~ 27V (This is the 28V supply minus approximately 1V on the diode). M/A-COM PIN Diode Driver, MADR-008888-0001TR is recommended for usage with the MASW000823-12770T SPDT Switch. The voltage at the common anode will be approximately 1.0V. The current in through the back-biased diodes will be the leakage current for the diodes C1-C5, L1-L3, R1, and the switch are discrete components that should be installed on the user’s board. It is recommended that Coilcraft 0603CS-27NXJLW or equivalent be used for L1-L3 at 2 GHz (values may vary based on the frequency). There are 33 pF bypass capacitors included in the driver for the RX and TX ports. There are cases, especially at higher frequencies, where the optional 12 pF bypass capacitors that are shown on the schematic are needed. 4 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, • India Tel: +91.80.43537383 • China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice. MADR-008888-000100 PIN Diode Driver for Series / Series High Power Switch Rev. 5 Lead-Free Land Grid Array, 0.64 in x 0.84 in † † Reference Application Note M538 for lead-free solder reflow recommendations. Meets JEDEC moisture sensitivity level 1 requirements. 5 ADVANCED: Data Sheets contain information regarding a product M/A-COM Technology Solutions • North America Tel: 800.366.2266 • Europe Tel: +353.21.244.6400 is considering for development. Performance is based on target specifications, simulated results, • India Tel: +91.80.43537383 • China Tel: +86.21.2407.1588 and/or prototype measurements. Commitment to develop is not guaranteed. Visit www.macomtech.com for additional data sheets and product information. PRELIMINARY: Data Sheets contain information regarding a product M/A-COM Technology Solutions has under development. Performance is based on engineering tests. Specifications are typical. Mechanical outline has been fixed. Engineering samples and/or test data may be available. M/A-COM Technology Solutions Inc. and its affiliates reserve the right to make Commitment to produce in volume is not guaranteed. changes to the product(s) or information contained herein without notice.