MN103SK7 Series MN103SK7N Type MN103SK7Q MN103SK7R Mask ROM Internal ROM type ROM (byte) 512K RAM (byte) 32K Package (Lead-free) Minimum Instruction Execution Time 768K 1024K 40K UBGA257-P-1111A 16.7 ns (at 2.7 V to 3.6 V, 60 MHz) Interrupts RESET. IRQ × 11. NMI. Key input. Timer × 32. Input capture × 16. PWM × 6. SIF × 24. I2C × 4. DMA × 18. WDT. A/D. System error Timer Counter 8-bit timer × 8 Reload-down count. Cascade connection possible (usable as a 16-bit to 32-bit timer) 16-bit timer × 6 Up-down count. Input capture. PWM output. Compare/capture register 2 channnels 16-bit timer × 6 Reload-down count Watchdog timer × 1 Serial interface UART/Synchronous interface selective × 10: Serial 0, 1, 3 to A Start-stop synchronization/Synchronization commonly used (16 bytes containing transmission/reception FIFO): Serial 2 I2C serial interface, multi master transmission/reception function × 2 DMA controller Number of channels: 6 channels Unit of transfer: 8/16/32 bits Maximum transfer cycles: 65535 Starting factor: External interrupt. Timer. Input capture. PWM. Serial transmission/reception. I2C transmission/reception. A/D conversion finish. Software Transfer method: 2-bus cycle transfer Adressing modes: Fixed. Increment. Decrement Transfer mode: Word transfer. Burst transfer. Intermittent transfer I/O Pins I/O Input 194 : Common use 1 : Exclusive A/D converter 10-bit × 32 channels PWM 12/14-bit resolution × 6 channels ICR 28-bit × 13 channels + 16-bit × 6 channels (common with timer) OCR 16-bit × 12 channels (common with timer) Timer Synchronous Output 4-bit (synchronous output) × 2 channels ROM Correction 8 channels MAF00038BEM MN103SK7N, MN103SK7Q, MN103SK7R Electrical Charactreistics (A/D converter characteristics) Parameter Symbol Condition min Limit typ max 10 Resolution Non-linear error VDD33 = 3.3 V. VSS = 0.0 V A/D conversion time IOCLK = 20 MHz. TAD = 200 ns Unit Bits LSB ±3 2.4 µs Ta = 25 °C Note) TAD is A/D conversion clock cycle Pin Assignment UBGA257-P-1111A A B C D E F G 20 VDDL VDDL PN0, PM3, PL7, PL4, PL1, TM20IOA SY0OT3 TM7IO TM4IO SCL0 H J PK6, KI6 PK2, KI2 19 VDDL VDDL PM7, PM5, PM1, PL6, PL3, PL0, SY1OT3 SY1OT1 SY0OT1 TM6IO TM3IO SDA0 PK4, KI4 18 PN2, PN1, VDDL PM6, PM4, PM0, PL5, PL2 TM22IOA TM21IOA SY1OT2 SY1OT0 SY0OT0 TM5IO PK5, KI5 K L PJ7, PK0, ADM15, KI0 A15 PJ6, PK1, ADM14, KI1 A14 PI7, PK3, ADM7, KI3 A7 PI6, VSS ADM6, A6 M N P PJ5, ADM13, A13 PJ4, ADM12, A12 PI5, ADM5, A5 PI4, ADM4, A4 PJ3, ADM11, A11 PJ2, ADM10, A10 PI3, ADM3, A3 PI2, ADM2, A2 PJ1, ADM9, A9 PJ0, ADM8, A8 PI1, ADM1, A1 PI0, ADM0, A0 R T U V W Y PH3, PH4, PH0, PG0, VDDB VDDB 20 SYSCLK DK NWE0 NCS0 PH5, AS PH2, NRE PG3, PG1, VDDB VDDB 19 NCS3 NCS1 PH6, PH1, PG2, VDDB PF7, PF6, 18 RWSEL NWE1 NCS2 TM2IO TM1IO 17 PP0, PN4, PN3, VDDL PM2, SBI7 TM21IOB TM20IOB SY0OT2 16 PP4, PP2, PP1, PN5, SBO8 SBT7 SBO7 TM22IOB PF1, IRQ7 PF3, IRQ9 PF0, IRQ6 15 PP7, PP5, SBO9 SBT8 PP6, SBI9 PP3, SBI8 PE3, NBG PE5 PE2, PE0, 15 NBR TM10IO 14 PR2, PR0, SBOA SBT9 PR1, SBIA VSS PR4, IRQ5 PR5 PR3, SBTA 13 12 PS0 PS4, PS2, PS3, TM14IO TM12IO TM13IO PS1 VSS N.C. PK7, KI7 N.C. VSS PG4, VDDB PF5, PF4, PF2, 17 NCS4 TM0IO IRQ10 IRQ8 PE4 PD5, D13, IRQ4 PD3, PD4, PD2, VSS D11, D12, D10, SBT6 IRQ3 SBO6 PC7, PD1, PD0, PC6, D6, D8, D9, D7, SBO5 SBI6 SBT5 SBI5 PC4, PC5, PC3, VDD33 D4, D3, D5, SBO4 SBT4 SBI4 PC0, PC2, PB5, PC1, D2, D0, D1, IRQ0 SBO3 SBI3 SBT3 PD6, PE1, PD7, D14 TM11IO D15 16 14 13 12 11 PS7 PS5, TM15IO PS6 VDD33 10 P00, AN0 P02, AN2 P04, AN4 P01, AN1 9 P03, AN3 P05, AN5 P06, AN6 VSS VSS PB2, SBI2 PB3, PB4, SBO2 SBT2 9 8 P07, AN7 P11, AN9 P12, AN10 P10, AN8 PA6, A22 PB0, A24 PA7, A23 PB1, A25 8 7 P13, P15, P17, P14, AN11 AN13 AN15 AN12 VSS PA4, A20 PA3, A19 PA5, A21 7 6 P16, P20, P24, P21, AN14 AN16 AN20 AN17 P96, IRQ1 PA1, A17 PA0, A16 PA2, A18 6 5 P22, P23, P26, AN18 AN19 AN22 P85, P94, P95, PWM5 SBO1 SBT1 P97, IRQ2 5 4 P25, P27, P30, VDD33 VSS AN21 AN23 AN24 P93, SBI1 4 3 P32, P31, VDD33 P34, P36, P51, P56, P61, AN26 AN25 AN28 AN30 TM24IOA SDA1 ICR1 VSS VSS N.C. P63, MMOD P65, ICR3 ICR5 P67, P73, OCD_SDA N.C. ICR7 ICR11 N.C. P82, VDD33 P92, P84, 3 SBT0 PWM4 PWM2 P35, P41, P50, P54, P57, 2 VDD33 VDD33 P33, AN27 AN29 WDOVF TM23IOA TM24IOB SCL1 P62, ICR2 VSS P66, P72, ICR6 ICR10 N.C. N.C. P80, P83, VDD33 VDD33 2 PWM0 PWM3 P55, P60, 1 VDD33 VDD33 VREFH P37, P40, P52, AN31 ADTRG TM25IOA TM25IOB ICR0 LON OSCI OSCO P75 N.C. OCD_SCL P81, VDD33 VDD33 1 PWM1 A B MAF00038BEM C D E F G H J K NRST L P64, ICR4 M P71, ICR9 N.C. N.C. P70, P74, ICR8 ICR12 N P VSS R P90, N.C. VDD33 SBI0 T U V P91, SBO0 10 P76, VOUT VOUT NMI VSS P53, N.C. TM23IOB 11 W Y Request for your special attention and precautions in using the technical information and semiconductors described in this book (1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) The technical information described in this book is intended only to show the main characteristics and application circuit examples of the products. No license is granted in and to any intellectual property right or other right owned by Panasonic Corporation or any other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) The products described in this book are intended to be used for general applications (such as office equipment, communications equipment, measuring instruments and household appliances), or for specific applications as expressly stated in this book. Consult our sales staff in advance for information on the following applications: – Special applications (such as for airplanes, aerospace, automotive equipment, traffic signaling equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. It is to be understood that our company shall not be held responsible for any damage incurred as a result of or in connection with your using the products described in this book for any special application, unless our company agrees to your using the products in this book for any special application. (4) The products and product specifications described in this book are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of our company. 20100202