M29F080A 8 Mbit (1Mb x8, Uniform Block) Single Supply Flash Memory ■ SINGLE 5V±10% SUPPLY VOLTAGE for PROGRAM, ERASE and READ OPERATIONS ■ ACCESS TIME: 70ns ■ PROGRAMMING TIME – 8µs by Byte typical ■ 16 UNIFORM 64 Kbyte MEMORY BLOCKS ■ PROGRAM/ERASE CONTROLLER 44 1 – Embedded Byte Program algorithm – Embedded Multi-Block/Chip Erase algorithm – Status Register Polling and Toggle Bits TSOP40 (N) 10 x 20mm SO44 (M) – Ready/Busy Output Pin ■ ERASE SUSPEND and RESUME MODES – Read and Program another Block during Erase Suspend ■ TEMPORARY BLOCK UNPROTECTION MODE ■ LOW POWER CONSUMPTION Figure 1. Logic Diagram VCC – Standby and Automatic Standby ■ ■ 100,000 PROGRAM/ERASE CYCLES per BLOCK 20 YEARS DATA RETENTION 20 8 A0-A19 DQ0-DQ7 – Defectivity below 1 ppm/year ■ ELECTRONIC SIGNATURE W – Manufacturer Code: 20h E – Device Code: F1h G M29F080A RB RP VSS AI00501C April 2000 1/21 M29F080A Figure 2. TSOP Connections A19 A18 A17 A16 A15 A14 A13 A12 E VCC NC RP A11 A10 A9 A8 A7 A6 A5 A4 1 10 11 Figure 3. SO Connections 40 M29F080A 20 31 30 21 NC NC W G RB DQ7 DQ6 DQ5 DQ4 VCC VSS VSS DQ3 DQ2 DQ1 DQ0 A0 A1 A2 A3 AI00520B NC RP A11 A10 A9 A8 A7 A6 A5 A4 NC NC A3 A2 A1 A0 DQ0 DQ1 DQ2 DQ3 VSS VSS 1 44 2 43 3 42 4 41 5 40 6 39 7 38 8 37 9 36 10 35 11 34 M29F080A 12 33 13 32 14 31 15 30 16 29 17 28 18 27 19 26 20 25 21 24 22 23 VCC E A12 A13 A14 A15 A16 A17 A18 A19 NC NC NC NC W G RB DQ7 DQ6 DQ5 DQ4 VCC AI00521B Table 1. Signal Names A0-A19 Address Inputs DQ0-DQ7 Data Inputs/Outputs E Chip Enable G Output Enable W Write Enable RP Reset/Block Temporary Unprotect RB Ready/Busy Output VCC Supply Voltage VSS Ground NC Not Connected Internally SUMMARY DESCRIPTION The M29F080A is an 8 Mbit (1Mb x8) non-volatile memory that can be read, erased and reprogrammed. These operations can be performed us- 2/21 ing a single 5V supply. On power-up the memory defaults to its Read mode where it can be read in the same way as a ROM or EPROM. The memory is divided into blocks that can be erased independently so it is possible to preserve valid data while old data is erased. Blocks can be protected in groups to prevent accidental Program or Erase commands from modifying the memory. Program and Erase commands are written to the Command Interface of the memory. An on-chip Program/Erase Controller simplifies the process of programming or erasing the memory by taking care of all of the special operations that are required to update the memory contents. The end of a program or erase operation can be detected and any error conditions identified. The command set required to control the memory is consistent with JEDEC standards. Chip Enable, Output Enable and Write Enable signals control the bus operation of the memory. They allow simple connection to most microprocessors, often without additional logic. The memory is offered in a TSOP40 (10 x 20mm) and SO44 packages and it is supplied with all the bits erased (set to ’1’). M29F080A Table 2. Absolute Maximum Ratings (1) Symbol Parameter Value Unit Ambient Operating Temperature (Temperature Range Option 1) 0 to 70 °C Ambient Operating Temperature (Temperature Range Option 6) –40 to 85 °C Ambient Operating Temperature (Temperature Range Option 3) –40 to 125 °C TBIAS Temperature Under Bias –50 to 125 °C TSTG Storage Temperature –65 to 150 °C VIO (2) Input or Output Voltage –0.6 to 6 V VCC Supply Voltage –0.6 to 6 V V ID Identification Voltage –0.6 to 13.5 V TA Note: 1. Except for the rating ”Operating Temperature Range”, stresses above those listed in the Table ”Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only and operation of the device at these or any other conditions above those indicated in the Operating sections of this specification is not implied. Exposure to Absolute Maximum Rating conditions for extended periods may affect device reliability. Refer also to the STMicroelectronics SURE Program and other relevant quality documents. 2. Minimum Voltage may undershoot to –2V during transition and for less than 20ns during transitions. Table 3. Uniform Block Addresses, M29F080A # Size (Kbytes) Address Range 15 64 F0000h-FFFFFh 14 64 E0000h-EFFFFh 13 64 D0000h-DFFFFh 12 64 C0000h-CFFFFh 11 64 B0000h-BFFFFh 10 64 A0000h-AFFFFh 9 64 90000h-9FFFFh 8 64 80000h-8FFFFh 7 64 70000h-7FFFFh 6 64 60000h-6FFFFh 5 64 50000h-5FFFFh 4 64 40000h-4FFFFh 3 64 30000h-3FFFFh 2 64 20000h-2FFFFh 1 64 10000h-1FFFFh 0 64 00000h-0FFFFh Protection Group 7 6 5 4 3 2 1 0 SIGNAL DESCRIPTIONS See Figure 1, Logic Diagram, and Table 1, Signal Names, for a brief overview of the signals connected to this device. Address Inputs (A0-A19). The Address Inputs select the cells in the memory array to access during Bus Read operations. During Bus Write operations they control the commands sent to the Command Interface of the internal state machine. Data Inputs/Outputs (DQ0-DQ7). The Data Inputs/Outputs output the data stored at the selected address during a Bus Read operation. During Bus Write operations they represent the commands sent to the Command Interface of the internal state machine. Chip Enable (E). The Chip Enable, E, activates the memory, allowing Bus Read and Bus Write operations to be performed. When Chip Enable is High, VIH, all other pins are ignored. Output Enable (G). The Output Enable, G, controls the Bus Read operation of the memory. Write Enable (W). The Write Enable, W, controls the Bus Write operation of the memory’s Command Interface. Reset/Block Temporary Unprotect (RP). The Reset/Block Temporary Unprotect pin can be used to apply a Hardware Reset to the memory or to temporarily unprotect all blocks that have been protected. 3/21 M29F080A A Hardware Reset is achieved by holding Reset/ Block Temporary Unprotect Low, VIL, for at least tPLPX. After Reset/Block Temporary Unprotect goes High, V IH, the memory will be ready for Bus Read and Bus Write operations after tPHEL or tRHEL, whichever occurs last. See the Ready/Busy Output section, Table 14 and Figure 11, Reset/ Temporary Unprotect AC Characteristics for more details. Holding RP at V ID will temporarily unprotect the protected blocks in the memory. Program and Erase operations on all blocks will be possible. The transition from VIH to VID must be slower than tPHPHH. Ready/Busy Output (RB). The Ready/Busy pin is an open-drain output that can be used to identify when the memory array can be read. Ready/Busy is high-impedance during Read mode, Auto Select mode and Erase Suspend mode. After a Hardware Reset, Bus Read and Bus Write operations cannot begin until Ready/Busy becomes high-impedance. See Table 14 and Figure 11, Reset/Temporary Unprotect AC Characteristics. During Program or Erase operations Ready/Busy is Low, VOL. Ready/Busy will remain Low during Read/Reset commands or Hardware Resets until the memory is ready to enter Read mode. The use of an open-drain output allows the Ready/ Busy pins from several memories to be connected to a single pull-up resistor. A Low will then indicate that one, or more, of the memories is busy. VCC Supply Voltage. The VCC Supply Voltage supplies the power for all operations (Read, Program, Erase etc.). The Command Interface is disabled when the VCC Supply Voltage is less than the Lockout Voltage, VLKO. This prevents Bus Write operations from accidentally damaging the data during power up, power down and power surges. If the Program/ Erase Controller is programming or erasing during this time then the operation aborts and the memory contents being altered will be invalid. 4/21 A 0.1µF capacitor should be connected between the VCC Supply Voltage pin and the VSS Ground pin to decouple the current surges from the power supply. The PCB track widths must be sufficient to carry the currents required during program and erase operations, I CC4. VSS Ground. The VSS Ground is the reference for all voltage measurements. BUS OPERATIONS There are five standard bus operations that control the device. These are Bus Read, Bus Write, Output Disable, Standby and Automatic Standby. See Table 4, Bus Operations, for a summary. Typically glitches of less than 5ns on Chip Enable or Write Enable are ignored by the memory and do not affect bus operations. Bus Read. Bus Read operations read from the memory cells, or specific registers in the Command Interface. A valid Bus Read operation involves setting the desired address on the Address Inputs, applying a Low signal, VIL, to Chip Enable and Output Enable and keeping Write Enable High, VIH. The Data Inputs/Outputs will output the value, see Figure 8, Read Mode AC Waveforms, and Table 11, Read AC Characteristics, for details of when the output becomes valid. Bus Write. Bus Write operations write to the Command Interface. A valid Bus Write operation begins by setting the desired address on the Address Inputs. The Address Inputs are latched by the Command Interface on the falling edge of Chip Enable or Write Enable, whichever occurs last. The Data Inputs/Outputs are latched by the Command Interface on the rising edge of Chip Enable or Write Enable, whichever occurs first. Output Enable must remain High, VIH, during the whole Bus Write operation. See Figures 9 and 10, Write AC Waveforms, and Tables 12 and 13, Write AC Characteristics, for details of the timing requirements. M29F080A Output Disable. The Data Inputs/Outputs are in the high impedance state when Output Enable is High, VIH. Standby. When Chip Enable is High, VIH, the Data Inputs/Outputs pins are placed in the highimpedance state and the Supply Current is reduced to the Standby level. When Chip Enable is at VIH the Supply Current is reduced to the TTL Standby Supply Current, I CC2. To further reduce the Supply Current to the CMOS Standby Supply Current, ICC3, Chip Enable should be held within VCC ± 0.2V. For Standby current levels see Table 10, DC Characteristics. During program or erase operations the memory will continue to use the Program/Erase Supply Current, ICC4, for Program or Erase operations until the operation completes. Automatic Standby. If CMOS levels (VCC ± 0.2V) are used to drive the bus and the bus is inactive for 150ns or more the memory enters Automatic Standby where the internal Supply Current is reduced to the Standby Supply Current, ICC3. The Data Inputs/Outputs will still output data if a Bus Read operation is in progress. Special Bus Operations Additional bus operations can be performed to read the Electronic Signature and also to apply and remove Block Protection. These bus operations are intended for use by programming equipment and are not usually used in applications. They require VID to be applied to some pins. Electronic Signature. The memory has two codes, the manufacturer code and the device code, that can be read to identify the memory. These codes can be read by applying the signals listed in Table 4, Bus Operations. Block Protection and Blocks Unprotection. Blocks can be protected in groups against accidental Program or Erase. See Table 3, Block Addresses, for details of which blocks must be protected together as a group. Protected blocks can be unprotected to allow data to be changed. Block Protection and Block Unprotection operations must only be performed on programming equipment. For further information refer to Application Note AN1122, Applying Protection and Unprotection to M29 Series Flash. Table 4. Bus Operations Operation G W Bus Read VIL V IL VIH Cell Address Bus Write VIL VIH VIL Command Address X VIH VIH X Hi-Z Standby VIH X X X Hi-Z Read Manufacturer Code VIL V IL VIH A0 = VIL, A1 = VIL, A9 = VID, Others VIL or VIH 20h Read Device Code VIL V IL VIH A0 = VIH, A1 = VIL, A9 = VID, Others VIL or VIH F1h Output Disable Address Inpu ts Data Inputs/Outpu ts E Data Output Data Input Note: X = VIL or VIH. 5/21 M29F080A COMMAND INTERFACE All Bus Write operations to the memory are interpreted by the Command Interface. Commands consist of one or more sequential Bus Write operations. Failure to observe a valid sequence of Bus Write operations will result in the memory returning to Read mode. In this case, after at least 50ns, an address transition or Chip Enable going Low is required before reading correct data. The long command sequences are imposed to maximize data security. The commands are summarized in Table 5, Commands. Refer to Table 5 in conjunction with the text descriptions below. Read/Reset Command. The Read/Reset command returns the memory to its Read mode where it behaves like a ROM or EPROM. It also resets the errors in the Status Register. Either one or three Bus Write operations can be used to issue the Read/Reset command. If the Read/Reset command is issued during a Block Erase operation or following a Programming or Erase error then the memory will take up to 10µs to abort. During the abort period no valid data can be read from the memory. Issuing a Read/Reset command during a Block Erase operation will leave invalid data in the memory. Auto Select Command. The Auto Select command is used to read the Manufacturer Code, the Device Code and the Block Protection Status. Three consecutive Bus Write operations are required to issue the Auto Select command. Once the Auto Select command is issued the memory remains in Auto Select mode until another command is issued. From the Auto Select mode the Manufacturer Code can be read using a Bus Read operation with A0 = VIL and A1 = VIL. The other address bits may be set to either VIL or VIH. The Manufacturer Code for STMicroelectronics is 20h. 6/21 The Device Code can be read using a Bus Read operation with A0 = VIH and A1 = VIL. The other address bits may be set to either VIL or VIH. The Device Code for the M29F080A is F1h. The Block Protection Status of each block can be read using a Bus Read operation with A0 = VIL, A1 = VIH, and A16-A19 specifying the address of the block. The other address bits may be set to either V IL or VIH. If the addressed block is protected then 01h is output on the Data Inputs/Outputs, otherwise 00h is output. Program Command. The Program command can be used to program a value to one address in the memory array at a time. The command requires four Bus Write operations, the final write operation latches the address and data in the internal state machine and starts the Program/Erase Controller. If the address falls in a protected block then the Program command is ignored, the data remains unchanged. The Status Register is never read and no error condition is given. During the program operation the memory will ignore all commands. It is not possible to issue any command to abort or pause the operation. Typical program times are given in Table 6. Bus Read operations during the program operation will output the Status Register on the Data Inputs/Outputs. See the section on the Status Register for more details. After the program operation has completed the memory will return to the Read mode, unless an error has occurred. When an error occurs the memory will continue to output the Status Register. A Read/Reset command must be issued to reset the error condition and return to Read mode. Note that the Program command cannot change a bit set at ’0’ back to ’1’. One of the Erase Commands must be used to set all the bits in a block or in the whole memory from ’0’ to ’1’. M29F080A Command Length Table 5. Commands Bus Write Operations 1st 2nd Addr Data 1 X F0 3 555 Auto Select 3 Program 3rd 4th Addr Data Addr Data AA 2AA 55 X F0 555 AA 2AA 55 555 90 4 555 AA 2AA 55 555 Chip Erase 6 555 AA 2AA 55 Block Erase 6+ 555 AA 2AA 55 Erase Suspend 1 X B0 Erase Resume 1 X 30 5th Addr Data A0 PA PD 555 80 555 555 80 555 6th Addr Data Addr Data AA 2AA 55 555 10 AA 2AA 55 BA 30 Read/Reset Note: X Don’t Care, PA Program Address, PD Program Data, BA Any address in the Block. All values in the table are in hexadecimal. The Command Interface only uses address bits A0-A10 to verify the commands, the upper address bits are Don’t Care. Read/Reset. After a Read/Reset command, read the memory as normal until another command is issued. Auto Select. After an Auto Select command, read Manufacturer ID, Device ID or Block Protection Status. Program, Chip Erase, Block Erase. After these commands read the Status Register until the Program/Erase Controller completes and the memory returns to Read Mode. Add additional Blocks during Block Erase Command with additional Bus Writ e Operations until the Timeout Bit is set. Erase Suspend. After the Erase Suspend command read non-erasing memory blocks as normal, issue Auto Select and Program commands on non-erasing blocks as normal. Erase Resume. After the Erase Resume command the suspended Erase operation resumes, read the Status Register until the Program/ Erase Controller completes and the memory returns to Read Mode. Chip Erase Command. The Chip Erase command can be used to erase the entire chip. Six Bus Write operations are required to issue the Chip Erase Command and start the Program/Erase Controller. If any blocks are protected then these are ignored and all the other blocks are erased. If all of the blocks are protected the Chip Erase operation appears to start but will terminate within about 100µs, leaving the data unchanged. No error condition is given when protected blocks are ignored. During the erase operation the memory will ignore all commands. It is not possible to issue any command to abort the operation. Typical chip erase times are given in Table 6. All Bus Read operations during the Chip Erase operation will output the Status Register on the Data Inputs/Outputs. See the section on the Status Register for more details. After the Chip Erase operation has completed the memory will return to the Read Mode, unless an error has occurred. When an error occurs the memory will continue to output the Status Register. A Read/Reset command must be issued to reset the error condition and return to Read Mode. The Chip Erase Command sets all of the bits in unprotected blocks of the memory to ’1’. All previous data is lost. 7/21 M29F080A Block Erase Command. The Block Erase command can be used to erase a list of one or more blocks. Six Bus Write operations are required to select the first block in the list. Each additional block in the list can be selected by repeating the sixth Bus Write operation using the address of the additional block. The Block Erase operation starts the Program/Erase Controller about 50µs after the last Bus Write operation. Once the Program/Erase Controller starts it is not possible to select any more blocks. Each additional block must therefore be selected within 50µs of the last block. The 50µs timer restarts when an additional block is selected. The Status Register can be read after the sixth Bus Write operation. See the Status Register for details on how to identify if the Program/Erase Controller has started the Block Erase operation. If any selected blocks are protected then these are ignored and all the other selected blocks are erased. If all of the selected blocks are protected the Block Erase operation appears to start but will terminate within about 100µs, leaving the data unchanged. No error condition is given when protected blocks are ignored. During the Block Erase operation the memory will ignore all commands except the Erase Suspend and Read/Reset commands. Typical block erase times are given in Table 6. All Bus Read operations during the Block Erase operation will output the Status Register on the Data Inputs/Outputs. See the section on the Status Register for more details. After the Block Erase operation has completed the memory will return to the Read Mode, unless an error has occurred. When an error occurs the memory will continue to output the Status Regis- ter. A Read/Reset command must be issued to reset the error condition and return to Read mode. The Block Erase Command sets all of the bits in the unprotected selected blocks to ’1’. All previous data in the selected blocks is lost. Erase Suspend Command. The Erase Suspend Command may be used to temporarily suspend a Block Erase operation and return the memory to Read mode. The command requires one Bus Write operation. The Program/Erase Controller will suspend within 15µs of the Erase Suspend Command being issued. Once the Program/Erase Controller has stopped the memory will be set to Read mode and the Erase will be suspended. If the Erase Suspend command is issued during the period when the memory is waiting for an additional block (before the Program/Erase Controller starts) then the Erase is suspended immediately and will start immediately when the Erase Resume Command is issued. It will not be possible to select any further blocks for erasure after the Erase Resume. During Erase Suspend it is possible to Read and Program cells in blocks that are not being erased; both Read and Program operations behave as normal on these blocks. Reading from blocks that are being erased will output the Status Register. It is also possible to enter the Auto Select mode: the memory will behave as in the Auto Select mode on all blocks until a Read/Reset command returns the memory to Erase Suspend mode. Erase Resume Command. The Erase Resume command must be used to restart the Program/ Erase Controller from Erase Suspend. An erase can be suspended and resumed more than once. Table 6. Program, Erase Times and Program, Erase Endurance Cycles (TA = 0 to 70 °C, –40 to 85 °C or –40 to 125 °C) Typ(1) Typical after 100k W/E Cycles(1) Chip Erase (All bits in the memory set to ‘0’) 3 3 Chip Erase 8 8 30 sec 0.6 0.6 4 sec Program 8 8 150 µs Chip Program 9 9 35 sec Parameter Min Block Erase (64 Kbytes) Program/Erase Cycles (per Block) Note: 1. TA = 25°C, VCC = 5V. 8/21 100,000 Max Unit sec cycles M29F080A STATUS REGISTER Bus Read operations from any address always read the Status Register during Program and Erase operations. It is also read during Erase Suspend when an address within a block being erased is accessed. The bits in the Status Register are summarized in Table 7, Status Register Bits. Data Polling Bit (DQ7). The Data Polling Bit can be used to identify whether the Program/Erase Controller has successfully completed its operation or if it has responded to an Erase Suspend. The Data Polling Bit is output on DQ7 when the Status Register is read. During Program operations the Data Polling Bit outputs the complement of the bit being programmed to DQ7. After successful completion of the Program operation the memory returns to Read mode and Bus Read operations from the address just programmed output DQ7, not its complement. During Erase operations the Data Polling Bit outputs ’0’, the complement of the erased state of DQ7. After successful completion of the Erase operation the memory returns to Read mode. In Erase Suspend mode the Data Polling Bit will output a ’1’ during a Bus Read operation within a block being erased. The Data Polling Bit will change from a ’0’ to a ’1’ when the Program/Erase Controller has suspended the Erase operation. Figure 4, Data Polling Flowchart, gives an example of how to use the Data Polling Bit. A Valid Ad- dress is the address being programmed or an address within the block being erased. Toggle Bit (DQ6). The Toggle Bit can be used to identify whether the Program/Erase Controller has successfully completed its operation or if it has responded to an Erase Suspend. The Toggle Bit is output on DQ6 when the Status Register is read. During Program and Erase operations the Toggle Bit changes from ’0’ to ’1’ to ’0’, etc., with successive Bus Read operations at any address. After successful completion of the operation the memory returns to Read mode. During Erase Suspend mode the Toggle Bit will output when addressing a cell within a block being erased. The Toggle Bit will stop toggling when the Program/Erase Controller has suspended the Erase operation. Figure 5, Data Toggle Flowchart, gives an example of how to use the Data Toggle Bit. Error Bit (DQ5). The Error Bit can be used to identify errors detected by the Program/Erase Controller. The Error Bit is set to ’1’ when a Program, Block Erase or Chip Erase operation fails to write the correct data to the memory. If the Error Bit is set a Read/Reset command must be issued before other commands are issued. The Error bit is output on DQ5 when the Status Register is read. Note that the Program command cannot change a bit set at ’0’ back to ’1’ and attempting to do so may or may not set DQ5 at ’1’. In both cases, a successive Bus Read operation will show the bit is still ’0’. One of the Erase commands must be used to set all the bits in a block or in the whole memory from ’0’ to ’1’. Table 7. Status Register Bits Operation Address DQ7 DQ6 DQ5 DQ3 DQ2 RB Program Any Address DQ7 Toggle 0 – – 0 Program During Erase Suspend Any Address DQ7 Toggle 0 – – 0 Program Error Any Address DQ7 Toggle 1 – – 0 Chip Erase Any Address 0 Toggle 0 1 Toggle 0 Block Erase before timeout Erasing Block 0 Toggle 0 0 Toggle 0 Non-Erasing Block 0 Toggle 0 0 No Toggle 0 Erasing Block 0 Toggle 0 1 Toggle 0 Non-Erasing Block 0 Toggle 0 1 No Toggle 0 Erasing Block 1 No Toggle 0 – Toggle 1 Block Erase Erase Suspend Non-Erasing Block Data read as normal 1 Good Block Address 0 Toggle 1 1 No Toggle 0 Faulty Block Address 0 Toggle 1 1 Toggle 0 Erase Error Note: Unspecified data bits should be ignored. 9/21 M29F080A Figure 4. Data Polling Flowchart Figure 5. Data Toggle Flowchart START START READ DQ5 & DQ6 READ DQ5 & DQ7 at VALID ADDRESS READ DQ6 DQ7 = DATA YES DQ6 = TOGGLE NO NO YES NO DQ5 =1 NO YES YES READ DQ7 at VALID ADDRESS DQ7 = DATA READ DQ6 TWICE YES DQ6 = TOGGLE NO FAIL DQ5 =1 NO YES PASS FAIL PASS AI01370B AI03598 Erase Timer Bit (DQ3). The Erase Timer Bit can be used to identify the start of Program/Erase Controller operation during a Block Erase command. Once the Program/Erase Controller starts erasing the Erase Timer Bit is set to ’1’. Before the Program/Erase Controller starts the Erase Timer Bit is set to ’0’ and additional blocks to be erased may be written to the Command Interface. The Erase Timer Bit is output on DQ3 when the Status Register is read. Alternative Toggle Bit (DQ2). The Alternative Toggle Bit can be used to monitor the Program/ Erase controller during Erase operations. The Alternative Toggle Bit is output on DQ2 when the Status Register is read. During Chip Erase and Block Erase operations the Toggle Bit changes from ’0’ to ’1’ to ’0’, etc., with 10/21 successive Bus Read operations from addresses within the blocks being erased. Once the operation completes the memory returns to Read mode. During Erase Suspend the Alternative Toggle Bit changes from ’0’ to ’1’ to ’0’, etc. with successive Bus Read operations from addresses within the blocks being erased. Bus Read operations to addresses within blocks not being erased will output the memory cell data as if in Read mode. After an Erase operation that causes the Error Bit to be set the Alternative Toggle Bit can be used to identify which block or blocks have caused the error. The Alternative Toggle Bit changes from ’0’ to ’1’ to ’0’, etc. with successive Bus Read Operations from addresses within blocks that have not erased correctly. The Alternative Toggle Bit does not change if the addressed block has erased correctly. M29F080A Table 8. AC Measurement Conditions M29F080A Parameter 70 90 / 120 High Speed Standard 30pF 100pF Input Rise and Fall Times ≤ 10ns ≤ 10ns Input Pulse Voltages 0 to 3V 0.45 to 2.4V 1.5V 0.8V and 2.0V AC Test Conditions Load Capacitance (CL) Input and Output Timing Ref. Voltages Figure 6. AC Testing Input Output Waveform Figure 7. AC Testing Load Circuit 1.3V High Speed 1N914 3V 1.5V 3.3kΩ 0V DEVICE UNDER TEST Standard 2.4V OUT CL = 30pF or 100pF 2.0V 0.8V 0.45V AI01275B CL includes JIG capacitance AI03027 Table 9. Capacitance (TA = 25 °C, f = 1 MHz) Symbol C IN COUT Parameter Input Capacitance Output Capacitance Test Condition Min Max Unit V IN = 0V 6 pF VOUT = 0V 12 pF Note: Sampled only, not 100% tested. 11/21 M29F080A Table 10. DC Characteristics (TA = 0 to 70°C, –40 to 85°C or –40 to 125°C) Symbol Parameter Test Condition Typ. (2) Max Unit 0V ≤ VIN ≤ VCC ±1 µA 0V ≤ VOUT ≤ VCC ±1 µA 20 mA 1 mA 150 µA 20 mA ILI Input Leakage Current ILO Output Leakage Current ICC1 Supply Current (Read) ICC2 Supply Current (Standby) TTL ICC3 Supply Current (Standby) CMOS E = VCC ± 0.2V, RP = VCC ± 0.2V ICC4 (1) Supply Current (Program/Erase) Program/Erase Controller active Min E = VIL, G = VIH, f = 6MHz 10 E = VIH 35 VIL Input Low Voltage –0.5 0.8 V VIH Input High Voltage 2 VCC + 0.5 V VOL Output Low Voltage 0.45 V Output High Voltage TTL IOH = –2.5mA 2.4 V Output High Voltage CMOS IOH = –100µA VCC – 0.4 V VOH VID Identification Voltage IID Identification Current VLKO (1) Program/Erase Lockout Supply Voltage Note: 1. Sampled only, not 100% tested. 2. TA = 25 °C, VCC = 5V. 12/21 IOL = 5.8mA 11.5 A9 = VID 3.2 12.5 V 100 µA 4.2 V M29F080A Table 11. Read AC Characteristics (TA = 0 to 70°C, –40 to 85°C or –40 to 125°C) M29F080A Symbol Alt Parameter Test Condition Unit 70 90 / 120 tAVAV tRC Address Valid to Next Address Valid E = VIL, G = VIL Min 70 90 ns tAVQV tACC Address Valid to Output Valid E = VIL, G = VIL Max 70 90 ns tELQX (1) tLZ Chip Enable Low to Output Transition G = VIL Min 0 0 ns tELQV tCE Chip Enable Low to Output Valid G = VIL Max 70 90 ns tGLQX (1) tOLZ Output Enable Low to Output Transition E = VIL Min 0 0 ns t GLQV tOE Output Enable Low to Output Valid E = VIL Max 30 35 ns tEHQZ (1) tHZ Chip Enable High to Output Hi-Z G = VIL Max 20 20 ns tGHQZ (1) tDF Output Enable High to Output Hi-Z E = VIL Max 20 20 ns tEHQX tGHQX t AXQX tOH Chip Enable, Output Enable or Address Transition to Output Transition Min 0 0 ns Note: 1. Sampled only, not 100% tested. Figure 8. Read Mode AC Waveforms tAVAV A0-A19 VALID tAVQV tAXQX E tELQV tEHQX tELQX tEHQZ G tGLQX tGLQV DQ0-DQ7 tGHQX tGHQZ VALID AI02925 13/21 M29F080A Table 12. Write AC Characteristics, Write Enable Controlled (TA = 0 to 70 °C, –40 to 85 °C or –40 to 125 °C) M29F080A Symbol Alt Parameter Unit 70 90 / 120 tAVAV tWC Address Valid to Next Address Valid Min 70 90 ns tELWL tCS Chip Enable Low to Write Enable Low Min 0 0 ns tWLWH t WP Write Enable Low to Write Enable High Min 45 45 ns tDVWH tDS Input Valid to Write Enable High Min 30 45 ns t WHDX tDH Write Enable High to Input Transition Min 0 0 ns t WHEH tCH Write Enable High to Chip Enable High Min 0 0 ns tWHWL tWPH Write Enable High to Write Enable Low Min 20 20 ns tAVWL tAS Address Valid to Write Enable Low Min 0 0 ns tWLAX tAH Write Enable Low to Address Transition Min 45 45 ns Output Enable High to Write Enable Low Min 0 0 ns tGHWL tWHGL tOEH Write Enable High to Output Enable Low Min 0 0 ns tWHRL (1) tBUSY Program/Erase Valid to RB Low Max 30 35 ns tVCHEL tVCS VCC High to Chip Enable Low Min 50 50 µs Note: 1. Sampled only, not 100% tested. Figure 9. Write AC Waveforms, Write Enable Controlled tAVAV A0-A19 VALID tWLAX tAVWL tWHEH E tELWL tWHGL G tGHWL tWLWH W tWHWL tDVWH DQ0-DQ7 tWHDX VALID VCC tVCHEL RB tWHRL 14/21 AI00524 M29F080A Table 13. Write AC Characteristics, Chip Enable Controlled (TA = 0 to 70 °C, –40 to 85 °C or –40 to 125 °C) M29F080A Symbol Alt Parameter Unit 70 90 / 120 tAVAV tWC Address Valid to Next Address Valid Min 70 90 ns tWLEL t WS Write Enable Low to Chip Enable Low Min 0 0 ns tELEH tCP Chip Enable Low to Chip Enable High Min 45 45 ns tDVEH tDS Input Valid to Chip Enable High Min 30 45 ns tEHDX tDH Chip Enable High to Input Transition Min 0 0 ns t EHWH tWH Chip Enable High to Write Enable High Min 0 0 ns tEHEL tCPH Chip Enable High to Chip Enable Low Min 20 20 ns tAVEL tAS Address Valid to Chip Enable Low Min 0 0 ns tELAX tAH Chip Enable Low to Address Transition Min 45 45 ns Output Enable High Chip Enable Low Min 0 0 ns tGHEL tEHGL tOEH Chip Enable High to Output Enable Low Min 0 0 ns tEHRL (1) tBUSY Program/Erase Valid to RB Low Max 30 35 ns tVCHWL tVCS VCC High to Write Enable Low Min 50 50 µs Note: 1. Sampled only, not 100% tested. Figure 10. Write AC Waveforms, Chip Enable Controlled tAVAV A0-A19 VALID tELAX tAVEL tEHWH W tWLEL tEHGL G tGHEL tELEH E tEHEL tDVEH DQ0-DQ7 tEHDX VALID VCC tVCHWL RB tEHRL AI00525 15/21 M29F080A Table 14. Reset/Block Temporary Unprotect AC Characteristics (TA = 0 to 70 °C, –40 to 85 °C or –40 to 125 °C) M29F080A Symbol tPHWL (1) tPHEL Alt Parameter Unit 70 90 / 120 tRH RP High to Write Enable Low, Chip Enable Low, Output Enable Low Min 50 50 ns tRB RB High to Write Enable Low, Chip Enable Low, Output Enable Low Min 0 0 ns tPLPX tRP RP Pulse Width Min 500 500 ns tPLYH (1) tREADY RP Low to Read Mode Max 10 10 µs tPHPHH (1) tVIDR RP Rise Time to VID Min 500 500 ns (1) tPHGL tRHWL (1) tRHEL (1) tRHGL (1) Note: 1. Sampled only, not 100% tested. Figure 11. Reset/Block Temporary Unprotect AC Waveforms W, E, G tPHWL, tPHEL, tPHGL RB tRHWL, tRHEL, tRHGL RP tPLPX tPHPHH tPLYH AI02931 16/21 M29F080A Table 15. Ordering Information Scheme Example: M29F080A 70 N 1 T Device Type M29 Operating Voltage F = VCC = 5V ± 10% Device Function 080A = 8 Mbit (1Mb x8), Uniform Block Speed 70 = 70 ns 90 = 90 ns 120 = 120ns Package N = TSOP40: 10 x 20 mm M = SO44 Temperature Range 1 = 0 to 70 °C 3 = –40 to 125 °C 6 = –40 to 85 °C Optio n T = Tape & Reel Packing Note: The last two characters of the ordering code may be replaced by a letter code for preprogrammed parts, otherwise devices are shipped from the factory with the memory content bits erased to ’1’. For a list of available options (Speed, Package, etc...) or for further information on any aspect of this device, please contact the ST Sales Office nearest to you. 17/21 M29F080A Table 16. Revision History Date Revision Details July 1999 First Issue 09/21/99 Removed 55ns speed option Chip Erase Max. specification added (Table 6) Block Erase Max. specification added (Table 6) Program Max. specification added (Table 6) Chip Program Max. specification added (Table 6) ICC1 Typ. specification added (Table 10) ICC3 Typ. specification added (Table 10) 10/04/99 ICC3 Test Condition change (Table 10) 11/12/99 Block Protection and Unprotection paragraph change 01/14/00 Command Interface paragraph change 03/30/00 New document template Document type: from Preliminary Data to Data Sheet Status Register bit DQ5 clarification Data Polling Flowchart diagram change (Figure 4) Data Toggle Flowchart diagram change (Figure 5) Restrictive Read AC Characteristics removed TSOP40 Package mechanical data change (Table 17) SO44 Package mechanical data change (Table 18) 18/21 M29F080A Table 17. TSOP40 - 40 lead Plastic Thin Small Outline, 10 x 20mm, Package Mechanical Data mm inches Symbol Typ Min Max A Typ Min 1.20 Max 0.0472 A1 0.05 0.15 0.0020 0.0059 A2 0.95 1.05 0.0374 0.0413 B 0.17 0.27 0.0067 0.0106 C 0.10 0.21 0.0039 0.0083 D 19.80 20.20 0.7795 0.7953 D1 18.30 18.50 0.7205 0.7283 E 9.90 10.10 0.3898 0.3976 – – – – L 0.50 0.70 0.0197 0.0276 α 0° 5° 0° 5° N 40 e 0.50 0.0197 40 CP 0.10 0.0039 Figure 12. TSOP40 - 40 lead Plastic Thin Small Outline, 10 x 20 mm, Package Outline A2 1 N e E B N/2 D1 A CP D DIE C TSOP-a A1 α L Drawing is not to scale. 19/21 M29F080A Table 18. SO44 - 44 lead Plastic Small Outline, 525 mils body width, Package Mechanical Data mm inches Symbol Typ Min Max A 2.42 A1 A2 Min Max 2.62 0.0953 0.1031 0.22 0.23 0.0087 0.0091 2.25 2.35 0.0886 0.0925 B Typ 0.50 0.0197 C 0.10 0.25 0.0039 0.0098 D 28.10 28.30 1.1063 1.1142 E 13.20 13.40 0.5197 0.5276 – – – – 15.90 16.10 0.6260 0.6339 e 1.27 H 0.0500 L 0.80 – – 0.0315 – – α 3° – – 3° – – N 44 CP 44 0.10 0.0039 Figure 13. SO44 - 44 lead Plastic Small Outline, 525 mils body width, Package Outline A2 A C B CP e D N E H 1 A1 SO-b Drawing is not to scale. 20/21 α L M29F080A Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in lif e support devices or systems without express written approval of STMicroelectronics. The ST logo is registered trademark of STMicroelectronics 2000 STMicroelectronics - All Rights Reserved All other names are the property of their respective owners. STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - U.S.A . http://w ww.st.com 21/21