HA17358A Series Dual Operational Amplifier REJ03D0676-0400 Rev.4.00 Mar 10, 2006 Description HA17358A series are dual operational amplifier that provide high gain and internal phase compensation, with single power supply. They can be widely applied to control equipments and to general use. Features • Wide range of supply voltage, and single power supply used • Wide range of common mode voltage, and possible to operate with an input about 0 V, and output around 0 V is available • Frequency characteristics and input bias current are temperature compensated • Low electro-magnetic susceptibility level Measurement Condition Output Offset Voltage vs. Input Interference 5.0 Vcc = +7.5 V Vee = −7.5 V Rs Rs − + Rf Vout V _ (= 100∗Vio) 0.01 µ Vin −10 dBm RF signal source (for quasi-RF noise) Output offset voltage (arb. unit) Rf 4.0 HA17358 series 3.0 2.0 Improvement 1.0 HA17358A series 0 −1.0 100E+3 1E+6 10E+6 100E+6 1E+9 Input RF frequency (Hz) 10E+9 Ordering Information Type No. HA17358A HA17358AF HA17358ARP HA17358AT Application Commercial use Rev.4.00 Mar 10, 2006 page 1 of 7 Package Name DIP-8 pin SOP-8 pin (JEITA) SOP-8 pin (JEDEC) TSSOP-8 pin Package Code PRDP0008AF-B PRSP0008DE-B PRSP0008DD-C PTSP0008JC-B HA17358A Series Pin Arrangement Vout1 1 Vin(−)1 2 Vin(+)1 3 GND 4 1 − + 2 + − 8 VCC 7 Vout2 6 Vin(−)2 5 Vin(+)2 (Top View) Circuit Schematic (1/2) Q5 Vin(−) Q1 Q2 Q3 Q4 Q6 C Q7 R1 Vin(+) Vout Q11 Q10 Q8 Q13 Q12 Q9 Note: If Input/Output terminals voltage over the absolute maximum ratings, there is possibility of mis-operation, characteristics deterioration and destruction, because of the current’s flowing to parasitic diode in IC. The Input/Output terminals are recommended to be protected with the clamp circuit which using the diode with low forward voltage (like schottky barrier diode) when there is a possibility for the Input/Output terminals voltage exceeds the absolute maximum ratings. Rev.4.00 Mar 10, 2006 page 2 of 7 HA17358A Series Absolute Maximum Ratings (Ta = 25°C) Item Power supply voltage Output sink current Common mode input voltage Differential input voltage Output voltage Allowable power dissipation Symbol DIP SOP TSSOP Operating temperature Storage temperature Ratings 32 50 −0.3 to +VCC ±VCC −0.3 to +VCC 570 *1 385 *2 192 *3 −40 to +85 −55 to +125 VCC Iosink VCM Vin(diff) Vout PT Topr Tstg Unit V mA V V V mW °C °C Notes: 1. HA17358A: This is the allowable values up to Ta = 50°C. Derate by 8.3 mW/°C. 2. HA17358AF/ARP: These are the allowable values up to Ta = 25°C mounting in air. When it is mounted on glass epoxy board of 40 mm × 40 mm × 1.5 mmt with 30% wiring density, the allowable value is 570 mW up to Ta = 45°C. If Ta > 45°C, derate by 7.14 mW/°C. 3. HA17358AT: These are the allowable values up to Ta = 25°C. Derate by 1.92 mW/°C above that temperature. Electrical Characteristics (VCC = +15 V, Ta = 25°C) Item Input offset voltage Input offset current Input bias current Power source rejection ratio Voltage gain Common mode rejection ratio Common mode input voltage range Peak-to-peak output voltage Symbol VIO IIO IIB PSRR AVD CMR VCM (+) VCM (–) VOP-P Min — — — — 75 — 13.5 — — Typ 3 5 30 93 90 80 — — 13.6 Max 7 50 250 — — — — –0.3 — Unit mV nA nA dB dB dB V V V Output source current Output sink current Iosource Iosink 20 10 15 40 20 50 — — — mA mA µA f = 100Hz, RL = 20kΩ, RS = 1kΩ, Rf = 100kΩ VIN+ = 1V, VIN– = 0V, VOH = 10V VIN– = 1V, VIN+ = 0V, VOL = 2.5V VIN– = 1V, VIN+ = 0V, Vout = 200mV Supply current Slew rate Channel separation *1 Note: 1. Design spec. ICC SR CS — — — 0.8 0.2 (120) 2 — — mA V/µs dB VIN = GND, RL = ∞ RL = ∞, VCM = 7.5V, f = 1.5kHz f = 1kHz Rev.4.00 Mar 10, 2006 page 3 of 7 Test Conditions VCM = 7.5V, RS = 50Ω, Rf = 50kΩ VCM = 7.5V, IIO = | II (+) – II (–) | VCM = 7.5V RS = 1kΩ, Rf = 100kΩ RL = ∞, RS = 1kΩ, Rf = 100kΩ RS = 50Ω, Rf = 5kΩ RS = 1kΩ, Rf = 100kΩ RS = 1kΩ, Rf = 100kΩ HA17358A Series Output Source Current vs. Ambient Temperature 80 VCC = 15 V 70 VOH = 10 V 60 50 40 30 20 10 0 −20 0 20 40 60 Ambeint temperature Ta (°C) Input Bias Current vs. Ambient Temperature 80 Input bias current IIB (nA) Output source current Iosource (mA) Characteristic Curves VCC = 15 V VCM = 7.5 V 70 60 50 40 30 20 10 0 −20 80 2 1 8 16 24 32 Supply voltage VCC (V) 80 Input bias current IIB (nA) Supply current ICC (mA) Ta = 25°C 3 0 40 20 0 40 120 80 40 40 Maximum output voltage VOP-P (V) Voltage gain AVD (dB) Ta = 25°C RL = ∞ Rev.4.00 Mar 10, 2006 page 4 of 7 8 16 24 32 Supply voltage VCC (V) 40 Maxlmum Output Voltage vs. Frequency 160 8 16 24 32 Supply voltage VCC (V) Ta = 25°C 60 Voltage Gain vs. Supply Voltage 0 80 Input Bias Current vs. Supply Voltage Supply Current vs. Supply Voltage 4 0 20 40 60 Ambeint temperature Ta (°C) 20 VCC = 15 V Ta = 25°C RL = 20 kΩ 16 12 8 4 0 1k 3k 10 k 30 k 100 k 300 k Frequency f (Hz) 1M HA17358A Series Voltage Gain vs. Frequency 120 VCC = 15V Ta = 25°C RL = ∞ Voltage gain AVD (dB) 100 80 60 40 20 0 1 3 10 30 100 300 1k 3k Frequency f (Hz) 10 k 30 k 100 k 300 k Common Mode Rejection Ratio vs. Frequency Common mode rejection ratio CMR (dB) 120 VCC = 15V Ta = 25°C RS = 50 Ω 100 80 60 40 20 0 100 Rev.4.00 Mar 10, 2006 page 5 of 7 300 1k 3 k 10 k 30 k 100 k 300 k Frequency f (Hz) 1M 1M HA17358A Series Package Dimensions JEITA Package Code P-DIP8-6.3x9.6-2.54 RENESAS Code PRDP0008AF-B Previous Code DP-8FV MASS[Typ.] 0.54g D 5 E 8 1 4 b3 0.89 A Z A1 Reference Dimension in Millimeters Symbol Min L e1 D E A A1 bp b3 c θ e Z L θ bp e c e1 ( Ni/Pd/Au plating ) JEITA Package Code P-SOP8-4.4x4.85-1.27 RENESAS Code PRSP0008DE-B *1 Previous Code FP-8DGV 0.5 0.40 0.48 0.56 1.30 0.19 0.25 0.31 15° 0° 2.29 2.54 2.79 1.27 2.54 MASS[Typ.] 0.1g F D 8 Nom Max 7.62 9.60 10.6 6.30 7.4 5.06 NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. 5 c *2 E HE bp Index mark Terminal cross section ( Ni/Pd/Au plating ) 1 Z Reference Dimension in Millimeters Symbol 4 e *3 bp x M A L1 A1 θ L y Detail F Rev.4.00 Mar 10, 2006 page 6 of 7 D E A2 A1 A bp b1 c c1 θ HE e x y Z L L1 Min Nom Max 4.85 5.25 4.4 0.00 0.1 0.35 0.4 0.20 2.03 0.45 0.15 0.20 0.25 0° 6.35 8° 6.5 6.75 1.27 0.12 0.15 0.75 0.42 0.60 0.85 1.05 HA17358A Series JEITA Package Code P-SOP8-3.95x4.9-1.27 RENESAS Code PRSP0008DD-C *1 Previous Code FP-8DCV MASS[Typ.] 0.085g F D 8 NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. 5 c *2 E HE bp Index mark Terminal cross section ( Ni/Pd/Au plating ) 1 Reference Dimension in Millimeters Symbol 4 *3 e Z bp x M A L1 A1 θ L y Detail F JEITA Package Code P-TSSOP8-4.4x3-0.65 RENESAS Code PTSP0008JC-B *1 Previous Code TTP-8DAV Min Nom Max 4.90 5.30 3.95 0.10 0.14 0.25 1.75 0.34 0.40 0.46 0.15 0.20 0.25 0° 8° 5.80 6.10 6.20 1.27 0.25 0.10 0.75 0.40 0.60 1.27 1.08 MASS[Typ.] 0.034g D 8 D E A2 A1 A bp b1 c c1 θ HE e x y Z L L1 F 5 NOTE) 1. DIMENSIONS"*1 (Nom)"AND"*2" DO NOT INCLUDE MOLD FLASH. 2. DIMENSION"*3"DOES NOT INCLUDE TRIM OFFSET. c HE *2 E bp Terminal cross section ( Ni/Pd/Au plating ) Reference Dimension in Millimeters Symbol Index mark L1 1 *3 bp x M θ A1 A Z 4 e L Detail F y Rev.4.00 Mar 10, 2006 page 7 of 7 D E A2 A1 A bp b1 c c1 θ HE e x y Z L L1 Min Nom Max 3.00 3.30 4.40 0.03 0.07 0.10 1.10 0.15 0.20 0.25 0.10 0.15 0.20 0° 8° 6.20 6.40 6.60 0.65 0.13 0.10 0.805 0.40 0.50 0.60 1.00 Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan Keep safety first in your circuit designs! 1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage. Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits, (ii) use of nonflammable material or (iii) prevention against any malfunction or mishap. Notes regarding these materials 1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party. 2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data, diagrams, charts, programs, algorithms, or circuit application examples contained in these materials. 3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product information before purchasing a product listed herein. The information described here may contain technical inaccuracies or typographical errors. Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors. Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor home page (http://www.renesas.com). 4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes no responsibility for any damage, liability or other loss resulting from the information contained herein. 5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater use. 6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials. 7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and cannot be imported into a country other than the approved destination. Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited. 8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein. http://www.renesas.com RENESAS SALES OFFICES Refer to "http://www.renesas.com/en/network" for the latest and detailed information. Renesas Technology America, Inc. 450 Holger Way, San Jose, CA 95134-1368, U.S.A Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501 Renesas Technology Europe Limited Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K. Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900 Renesas Technology (Shanghai) Co., Ltd. Unit 204, 205, AZIACenter, No.1233 Lujiazui Ring Rd, Pudong District, Shanghai, China 200120 Tel: <86> (21) 5877-1818, Fax: <86> (21) 6887-7898 Renesas Technology Hong Kong Ltd. 7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong Tel: <852> 2265-6688, Fax: <852> 2730-6071 Renesas Technology Taiwan Co., Ltd. 10th Floor, No.99, Fushing North Road, Taipei, Taiwan Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999 Renesas Technology Singapore Pte. Ltd. 1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632 Tel: <65> 6213-0200, Fax: <65> 6278-8001 Renesas Technology Korea Co., Ltd. Kukje Center Bldg. 18th Fl., 191, 2-ka, Hangang-ro, Yongsan-ku, Seoul 140-702, Korea Tel: <82> (2) 796-3115, Fax: <82> (2) 796-2145 Renesas Technology Malaysia Sdn. Bhd Unit 906, Block B, Menara Amcorp, Amcorp Trade Centre, No.18, Jalan Persiaran Barat, 46050 Petaling Jaya, Selangor Darul Ehsan, Malaysia Tel: <603> 7955-9390, Fax: <603> 7955-9510 © 2006. Renesas Technology Corp., All rights reserved. Printed in Japan. Colophon .6.0