TDK ACT45B Common mode filters for automobile signal line Datasheet

E M C
C o m p o n e n t s
February 2016
Common Mode Filters
For automobile signal line
ACT Series
ACT45B Type
ACT45B
[1812 inch]* (CAN-BUS)
* Dimensions Code JIS[EIA]
(2/7)
E M C
C o m p o n e n t s
REMINDERS FOR USING THESE PRODUCTS
Before using these products, be sure to request the delivery specifications.
SAFETY REMINDERS
Please pay sufficient attention to the warnings for safe designing when using these products.
REMINDERS
The storage period is less than 12 months. Be sure to follow the storage conditions (Temperature: 5 to 40°C, Humidity: 10 to 75% RH
or less).
If the storage period elapses, the soldering of the terminal electrodes may deteriorate.
Do not use or store in locations where there are conditions such as gas corrosion (salt, acid, alkali, etc.).
Before soldering, be sure to preheat components.
The preheating temperature should be set so that the temperature difference between the solder temperature and chip temperature
does not exceed 150°C.
Soldering corrections after mounting should be within the range of the conditions determined in the specifications.
If overheated, a short circuit, performance deterioration, or lifespan shortening may occur.
When embedding a printed circuit board where a chip is mounted to a set, be sure that residual stress is not given to the chip due to
the overall distortion of the printed circuit board and partial distortion such as at screw tightening portions.
Self heating (temperature increase) occurs when the power is turned ON, so the tolerance should be sufficient for the set thermal
design.
Carefully lay out the coil for the circuit board design of the non-magnetic shield type.
A malfunction may occur due to magnetic interference.
Use a wrist band to discharge static electricity in your body through the grounding wire.
Do not expose the products to magnets or magnetic fields.
Do not use for a purpose outside of the contents regulated in the delivery specifications.
The products listed on this catalog are intended for use in general electronic equipment (AV equipment, telecommunications
equipment, home appliances, amusement equipment, computer equipment, personal equipment, office equipment, measurement
equipment, industrial robots) under a normal operation and use condition.
The products are not designed or warranted to meet the requirements of the applications listed below, whose performance and/or
quality require a more stringent level of safety or reliability, or whose failure, malfunction or trouble could cause serious damage to
society, person or property.
If you intend to use the products in the applications listed below or if you have special requirements exceeding the range or conditions
set forth in the each catalog, please contact us.
(1) Aerospace/Aviation equipment
(2) Transportation equipment (electric trains, ships, etc.)
(3) Medical equipment
(4) Power-generation control equipment
(5) Atomic energy-related equipment
(6) Seabed equipment
(7) Transportation control equipment
(8) Public information-processing equipment
(9) Military equipment
(10) Electric heating apparatus, burning equipment
(11) Disaster prevention/crime prevention equipment
(12) Safety equipment
(13) Other applications that are not considered general-purpose
applications
When designing your equipment even for general-purpose applications, you are kindly requested to take into consideration securing
protection circuit/device or providing backup circuits in your equipment.
20160216 / cmf_automotive_signal_act45b_en.fm
(3/7)
E M C
C o m p o n e n t s
Common Mode Filters
Product compatible with RoHS directive
Compatible with lead-free solders
AEC-Q200
For automobile signal line
Overview of ACT45B Type
FEATURES
Compatible with an operating temperature range of –40 to +150°C, so can be used for vehicle devices requiring compatibility with high
temperatures.
When mounting, the terminal and winding tape splicing part do not fuse.
APPLICATION
CAN-BUS, FAXs, modems, ISDNs, etc.
PART NUMBER CONSTRUCTION
ACT45B
Series • Type name
-
110
Inductance(typ.)
(μH)
110
11
220
22
510
51
101
100
-
2P
-
Number of lines
2P
2 lines
TL
TL
□□□
Packaging style
Internal code
ø330mm reel
OPERATING TEMPERATURE RANGE, PACKAGE QUANTITY, PRODUCT WEIGHT
Temperature range
Operating
Storage
Type
temperature
temperature
(°C)
(°C)
ACT45B
–40 to +150
–40 to +150
The Storage temperature range is for after the circuit board is mounted.
Package quantity
Individual weight
(pieces/reel)
2,500
(g)
0.14
RoHS Directive Compliant Product: See the following for more details related to RoHS Directive compliant products. http://product.tdk.com/en/environment/rohs/
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160216 / cmf_automotive_signal_act45b_en.fm
(4/7)
E M C
C o m p o n e n t s
ACT45B Type
RECOMMENDED REFLOW PROFILE
Preheating
Soldering
Natural
cooling
Peak
T: Temperature
T4
T3
T2
T3
t3
T1
t1
t2
t: Time
Preheating
Temp.
T1
T2
150°C
180°C
Time
t1
60 to 120s
Soldering
Temp.
Time
T3
t2
230°C
40s max.
Peak
Temp.
T4
245°C
Time
t3
5s
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160216 / cmf_automotive_signal_act45b_en.fm
(5/7)
E M C
C o m p o n e n t s
ACT45B Type
SHAPE & DIMENSIONS
4.5±0.2
4
2
3
Marking
2.8±0.2
3.2±0.2
1
0.65±0.1
0.7±0.1
Dimensions in mm
1.6
CIRCUIT DIAGRAM
3.4
RECOMMENDED LAND PATTERN
1
4
2
3
• No polarity
3.2
5.9
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160216 / cmf_automotive_signal_act45b_en.fm
(6/7)
E M C
C o m p o n e n t s
ACT45B Type
ELECTRICAL CHARACTERISTICS
CHARACTERISTICS SPECIFICATION TABLE
Common mode
impedance
Common mode
inductance
Stray
inductance
[10MHz]
(: )min.
300
500
1000
2000
[100kHz]
(μH)+50/–30%
11
22
51
100
[100kHz]
(μH)typ.
0.05
0.08
0.15
0.20
(: )typ.
600
1200
2800
5800
DC resistance Rated current
Insulation
resistance
Rated voltage
Part No.
(: )max.
0.6
1.0
1.0
2.0
(M: )min.
10
10
10
10
(V)max.
50
50
50
50
ACT45B-110-2P-TL□□□
ACT45B-220-2P-TL□□□
ACT45B-510-2P-TL□□□
ACT45B-101-2P-TL□□□
○ Measurement equipment
Measurement item
Product No.
Common mode impedance
4991A
Common mode inductance
4294A
DC resistance
4338A
Insulation resistance
4339A
* Equivalent measurement equipment may be used.
(A)max.
0.25
0.2
0.2
0.15
Manufacturer
Agilent Technologies
Agilent Technologies
Agilent Technologies
Agilent Technologies
IMPEDANCE VS. FREQUENCY CHARACTERISTICS
100000
510 Common mode
101 Common mode
10000
Impedance (Ω)
220 Common mode
1000
510 Differential mode
110 Common mode
101 Differential mode
100
220 Differential mode
110 Differential mode
10
1
10
100
1000
Frequency (MHz)
○ Measurement equipment
Product No.
Manufacturer
4991A
Agilent Technologies
* Equivalent measurement equipment may be used.
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160216 / cmf_automotive_signal_act45b_en.fm
(7/7)
E M C
C o m p o n e n t s
ACT45B Type
PACKAGING STYLE
REEL DIMENSIONS
2.0±0.5
E
A
ø330±2
W1
13.5±0.5
W2
17.5±1
N
100±1
E
2 typ.
N
Type
ACT45B
1.0
ø13.0±0.2
W1
ø21.0±0.8
W2
A
Dimensions in mm
TAPE DIMENSIONS
P0
t
B
W
F
P2
E
øD0
A
K
P1
Dimensions in mm
Type
ACT45B
Blank
160min.
A
3.6±0.1
B
4.9±0.1
øD0
1.55±0.05
E
1.75±0.1
Products
F
5.5±0.05
P0
4.0±0.1
P1
8.0±0.1
P2
2.0±0.05
W
12.0±0.2
K
3.05±0.1
t
0.3±0.05
Blank
400 to 500
Start
End
Drawing direction
Dimensions in mm
Please be sure to request delivery specifications that provide further details on the features and specifications of the products for proper and safe use.
Please note that the contents may change without any prior notice due to reasons such as upgrading.
20160216 / cmf_automotive_signal_act45b_en.fm
Similar pages