NL27WZ14 Dual Schmitt−Trigger Inverter http://onsemi.com MARKING DIAGRAMS 6 6 M The NL27WZ14 is a high performance dual inverter with Schmitt−Trigger inputs operating from a 1.65 to 5.5 V supply. Pin configuration and function are the same as the NL27WZ04, but the inputs have hysteresis and, with its Schmitt trigger function, the NL27WZ14 can be used as a line receiver which will receive slow input signals. The NL27WZ14 is capable of transforming slowly changing input signals into sharply defined, jitter−free output signals. In addition, it has a greater noise margin than conventional inverters. The NL27WZ14 has hysteresis between the positive−going and the negative−going input thresholds (typically 1 V) which is determined internally by transistor ratios and is essentially insensitive to temperature and supply voltage variations. 1 SC−88/SOT−363/SC70−6 DF SUFFIX CASE 419B MA M G G 1 Features • Designed for 1.65 V to 5.5 V VCC Operation • Over Voltage Tolerant Inputs and Outputs • LVTTL Compatible − Interface Capability with 5 V TTL Logic • • • • • • with VCC = 3 V LVCMOS Compatible 24 mA Balanced Output Sink and Source Capability Near Zero Static Supply Current Substantially Reduces System Power Requirements Current Drive Capability is 24 mA at the Outputs Chip Complexity: FET = 72 Pb−Free Packages are Available 6 6 MA M G G 1 TSOP−6/SOT−23−6/SC59−6 DT SUFFIX CASE 318G 1 MA = Device Marking M = Date Code* G = Pb−Free Package (Note: Microdot may be in either location) *Date Code orientation and/or position may vary depending upon manufacturing location. PIN ASSIGNMENT IN A1 1 6 OUT Y1 GND 2 5 VCC IN A2 4 3 OUT Y2 Pin Function 1 IN A1 2 GND 3 IN A2 4 OUT Y2 5 VCC 6 OUT Y1 Figure 1. Pinout (Top View) IN A1 1 OUT Y1 IN A2 1 OUT Y2 FUNCTION TABLE A Input Y Output L H H L ORDERING INFORMATION See detailed ordering and shipping information in the package dimensions section on page 2 of this data sheet. Figure 2. Logic Symbol © Semiconductor Components Industries, LLC, 2007 February, 2007 − Rev. 9 1 Publication Order Number: NL27WZ14/D NL27WZ14 MAXIMUM RATINGS Symbol VCC Characteristics Value Unit *0.5 to )7.0 V *0.5 ≤ VI ≤ )7.0 V *0.5 ≤ VO ≤ 7.0 V VI < GND *50 mA VO < GND DC Supply Voltage VI DC Input Voltage VO DC Output Voltage IIK DC Input Diode Current IOK DC Output Diode Current *50 mA IO DC Output Sink Current $50 mA ICC DC Supply Current per Supply Pin $100 mA IGND DC Ground Current per Ground Pin $100 mA TSTG Storage Temperature Range *65 to )150 °C PD Power Dissipation in Still Air SC−88, TSOP−6 200 mW qJA Thermal Resistance SC−88, TSOP−6 333 °C/W TL Lead Temperature, 1 mm from case for 10 s 260 °C TJ Junction Temperature under Bias )150 °C > 2000 > 200 N/A V VESD Output in Z or LOW State (Note 1) ESD Withstand Voltage Human Body Model (Note 2) Machine Model (Note 3) Charged Device Model (Note 4) Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect device reliability. 1. IO absolute maximum rating must be observed. 2. Tested to EIA/JESD22−A114−A 3. Tested to EIA/JESD22−A115−A 4. Tested to JESD22−C101−A RECOMMENDED OPERATING CONDITIONS Symbol VCC Parameter Supply Voltage VI Input Voltage VO Output Voltage TA Operating Free−Air Temperature Dt/DV Input Transition Rise or Fall Rate Operating Data Retention Only (High or LOW State) VCC = 2.5 V $0.2 V VCC =3.0 V $0.3 V VCC =5.0 V $0.5 V Min Max Unit 2.3 1.5 5.5 5.5 V 0 5.5 V 0 5.5 V *55 )125 °C 0 0 0 No Limit No Limit No Limit ns/V ORDERING INFORMATION Device Package NL27WZ14DFT2 SC−88/SOT−363/SC70−6 NL27WZ14DFT2G SC−88/SOT−363/SC70−6 (Pb−Free) Shipping† 3000 / Tape & Reel NL27WZ14DTT1 TSOP−6/SOT−23−6/SC59−6 NL27WZ14DTT1G TSOP−6/SOT−23−6/SC59−6 (Pb−Free) †For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging Specifications Brochure, BRD8011/D. http://onsemi.com 2 NL27WZ14 DC ELECTRICAL CHARACTERISTICS VCC Symbol Parameter *55°C ≤ TA ≤ 125°C (V) Min Typ Max Min Max Min Max Unit VT) Positive Input Threshold Voltage 2.3 2.7 3.0 4.5 5.5 1.0 1.2 1.3 1.9 2.2 1.5 1.7 1.9 2.7 3.3 1.8 2.0 2.2 3.1 3.6 1.0 1.2 1.3 1.9 2.2 1.8 2.0 2.2 3.1 3.6 1.0 1.2 1.3 1.9 2.2 1.8 2.0 2.2 3.1 3.6 V VT* Negative Input Threshold Voltage 2.3 2.7 3.0 4.5 5.5 0.4 0.5 0.6 1.0 1.2 0.75 0.87 1.0 1.5 1.9 1.15 1.4 1.5 2.0 2.3 0.4 0.5 0.6 1.0 1.2 1.15 1.4 1.5 2.0 2.3 0.4 0.5 0.6 1.0 1.2 1.15 1.4 1.5 2.0 2.3 V VH Input Hysteresis Voltage 2.3 2.7 3.0 4.5 5.5 0.25 0.3 0.4 0.6 0.7 0.75 0.83 0.93 1.2 1.4 1.1 1.15 1.2 1.5 1.7 0.25 0.3 0.4 0.6 0.7 1.1 1.15 1.2 1.5 1.7 0.25 0.3 0.4 0.6 0.7 1.1 1.15 1.2 1.5 1.7 V VOH High−Level Output Voltage IOH = −100 mA IOH = *3 mA IOH = *8 mA IOH = *12 mA IOH = *16 mA IOH = *24 mA IOH = *32 mA 1.65 to 5.5 1.65 2.3 2.7 3.0 3.0 4.5 VCC − 0.1 1.29 1.9 2.2 2.4 2.3 3.8 VCC 1.52 2.1 2.4 2.7 2.5 4.0 IOL = 100 mA IOL = 4 mA IOL = 8 mA IOL = 12 mA IOL = 16 mA IOL = 24 mA IOL = 32 mA 1.65 to 5.5 1.65 2.3 2.7 3.0 3.0 4.5 VIN = VIH or VIL VOL Low−Level Output Voltage VIN = VIH or VIL Condition *40°C ≤ TA ≤ 85°C TA = 25°C IIN Input Leakage Current VIN = VCC or GND IOFF Power Off−Output Leakage Current VOUT = 5.5 V ICC Quiescent Supply Current VIN = VCC or GND VCC − 0.1 1.29 1.9 2.2 2.4 2.3 3.8 VCC − 0.1 1.29 1.8 2.1 2.3 2.2 3.7 V 0.1 0.24 0.3 0.4 0.4 0.55 0.55 0.1 0.24 0.3 0.4 0.4 0.55 0.55 0.1 0.24 0.4 0.5 0.5 0.55 0.65 V 0 to 5.5 $0.1 $1.0 $1.0 mA 0 1 10 10 mA 5.5 1 10 10 mA 0.08 0.2 0.22 0.28 0.38 0.42 ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎ ÎÎ ÎÎÎ ÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎ ÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎ ÎÎÎ ÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎ ÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎ ÎÎÎ ÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎ ÎÎÎÎ ÎÎÎÎÎ ÎÎÎÎÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎ ÎÎÎÎ ÎÎÎÎ ÎÎ ÎÎ ÎÎ ÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎÎ AC ELECTRICAL CHARACTERISTICS (Input tr = tf = 3.0 ns) *40°C ≤ TA ≤ 85°C TA = 25°C *55°C ≤ TA ≤ 125°C Symbol Parameter Condition VCC (V) Min Typ Max Min Max Min Max tPLH tPHL Propagation Delay Input A to Y (Figure 3 and 4) RL = 1 MW, CL = 15 pF 2.5 $ 0.2 1.8 4.3 7.4 1.8 8.1 1.8 9.1 Unit ns RL = 1 MW, CL = 15 pF RL = 500 W, CL = 50 pF 3.3 $ 0.3 1.5 1.8 3.3 4.0 5.0 6.0 1.5 1.8 5.5 6.6 1.5 1.8 6.5 7.6 RL = 1 MW, CL = 15 pF RL = 500 W, CL = 50 pF 5.0 $ 0.5 1.0 1.2 2.7 3.2 4.1 4.9 1.0 1.2 4.5 5.4 1.0 1.2 5.5 6.4 CAPACITIVE CHARACTERISTICS Symbol Parameter CIN Input Capacitance CPD Power Dissipation Capacitance (Note 5) Condition Typical Unit VCC =5.5 V, VI = 0 V or VCC 2.5 pF 10 MHz, VCC = 3.3 V, VI = 0 V or VCC 10 MHz, VCC = 5.0 V, VI = 0 V or VCC 11 12.5 pF 5. CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC(OPR) = CPD VCC fin ) ICC. CPD is used to determine the no−load dynamic power consumption; PD = CPD VCC2 fin ) ICC VCC. http://onsemi.com 3 NL27WZ14 VCC VCC A or B 50% GND tPLH Y PULSE GENERATOR DUT tPHL RT CL RL 50% VCC RT = CL or equivalent (includes jog and probe capacitance) RT = ZOUT of pulse generator (typically 50 W) VT , TYPICAL INPUT THRESHOLD VOLTAGE (VOLTS) Figure 3. Switching Waveforms Figure 4. Test Circuit 4 3 (VT)) 2 VHtyp (VT*) 1 2 2.5 3.5 3 VCC, POWER SUPPLY VOLTAGE (VOLTS) VHtyp = (VT) typ) − (VT* typ) 3.6 Figure 5. Typical Input Threshold, VT), VT* versus Power Supply Voltage VH Vin VCC VCC VH VT) VT* VT) VT* Vin GND GND VOH VOH Vout Vout VOL VOL (a) A Schmitt−Trigger Squares Up Inputs With Slow Rise and Fall Times (b) A Schmitt−Trigger Offers Maximum Noise Immunity Figure 6. Typical Schmitt−Trigger Applications http://onsemi.com 4 NL27WZ14 PACKAGE DIMENSIONS SC−88/SC70−6/SOT−363 CASE 419B−02 ISSUE W NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: INCH. 3. 419B−01 OBSOLETE, NEW STANDARD 419B−02. D e 6 5 4 1 2 3 HE DIM A A1 A3 b C D E e L HE −E− b 6 PL 0.2 (0.008) M E M MILLIMETERS MIN NOM MAX 0.80 0.95 1.10 0.00 0.05 0.10 0.20 REF 0.10 0.21 0.30 0.10 0.14 0.25 1.80 2.00 2.20 1.15 1.25 1.35 0.65 BSC 0.10 0.20 0.30 2.00 2.10 2.20 A3 C A A1 L SOLDERING FOOTPRINT* 0.50 0.0197 0.65 0.025 0.65 0.025 0.40 0.0157 1.9 0.0748 SCALE 20:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. http://onsemi.com 5 INCHES NOM MAX 0.037 0.043 0.002 0.004 0.008 REF 0.004 0.008 0.012 0.004 0.005 0.010 0.070 0.078 0.086 0.045 0.049 0.053 0.026 BSC 0.004 0.008 0.012 0.078 0.082 0.086 MIN 0.031 0.000 NL27WZ14 PACKAGE DIMENSIONS TSOP−6 CASE 318G−02 ISSUE S NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. MAXIMUM LEAD THICKNESS INCLUDES LEAD FINISH THICKNESS. MINIMUM LEAD THICKNESS IS THE MINIMUM THICKNESS OF BASE MATERIAL. 4. DIMENSIONS A AND B DO NOT INCLUDE MOLD FLASH, PROTRUSIONS, OR GATE BURRS. D 6 HE 1 5 4 2 3 E b DIM A A1 b c D E e L HE q e q c A 0.05 (0.002) L A1 MIN 0.90 0.01 0.25 0.10 2.90 1.30 0.85 0.20 2.50 0° MILLIMETERS NOM MAX 1.00 1.10 0.06 0.10 0.38 0.50 0.18 0.26 3.00 3.10 1.50 1.70 0.95 1.05 0.40 0.60 2.75 3.00 10° − MIN 0.035 0.001 0.010 0.004 0.114 0.051 0.034 0.008 0.099 0° INCHES NOM 0.039 0.002 0.014 0.007 0.118 0.059 0.037 0.016 0.108 − MAX 0.043 0.004 0.020 0.010 0.122 0.067 0.041 0.024 0.118 10° SOLDERING FOOTPRINT* 2.4 0.094 1.9 0.075 0.95 0.037 0.95 0.037 0.7 0.028 1.0 0.039 SCALE 10:1 mm Ǔ ǒinches *For additional information on our Pb−Free strategy and soldering details, please download the ON Semiconductor Soldering and Mounting Techniques Reference Manual, SOLDERRM/D. ON Semiconductor and are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner. PUBLICATION ORDERING INFORMATION LITERATURE FULFILLMENT: Literature Distribution Center for ON Semiconductor P.O. Box 5163, Denver, Colorado 80217 USA Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada Email: [email protected] N. American Technical Support: 800−282−9855 Toll Free USA/Canada Europe, Middle East and Africa Technical Support: Phone: 421 33 790 2910 Japan Customer Focus Center Phone: 81−3−5773−3850 http://onsemi.com 6 ON Semiconductor Website: www.onsemi.com Order Literature: http://www.onsemi.com/orderlit For additional information, please contact your local Sales Representative NL27WZ14/D