Systemsensor MOD400R High-temperature duct smoke detector Datasheet

H
V
A
C
S
y
s
t
e
m
s
M
o
n
i
t
o
r
i
n
g
400 Series™
High-Temperature
Duct Smoke Detector
Models Available
DH400ACDCIHT
4-wire ionization high-temperature duct
smoke detector
Product Overview
System Sensor DH400ACDCIHT is designed for interior
or exterior duct applications where extreme temperatures
can exceed standard detector capabilities. (For exterior
applications use DH400 OE-1 outdoor enclosure.) The
DH400ACDCIHT samples air currents passing through a
duct to provide dependable performance for management
of fans, blowers, and air conditioning systems. The twist-in,
twist-out 1451DHHT High-Temperature ionization detector head allows easy removal for quick cleaning, maintenance, and replacement without removing the duct housing.
Temperature range 32° – 158°F (0° – 70°C)
Agency Listings
Air velocity rating from 500 – 4,000 FPM
DH400ACDCIHT
APA451
RTS451KEY
RTS451
RA400Z
PA400W
24 VAC/DC or 120/220 VAC operation
Easy and quick mounting to round or rectangular
ducts from 1′ – 12′ (0.3 – 3.7 meters) wide
UL
UL
UL
UL
UL
UL
S911
S4011
S2522
S2522
S2522
S3593
3-year warranty
Accessories
System Sensor provides system flexibility with a variety of
accessories, including two remote test stations, and several
different means of visible and audible system annunciation.
ALARM
ALARM
POWER
RESET
ON
TEST
As with our duct detectors, all duct detector accessories are
UL listed.
F
I
R
E
ALARM
RESET
APA451
RTS451KEY
PA400W with
RTS451
Piezo
Remote Test
PS24LOW Add-on Strobe
Remote Test
Remote
Annunciator
Station with Key
Station
Annunciator
RA400Z
Architect/Engineer Specifications
The air duct smoke detector shall be a System Sensor
Model DH400ACDCIHT Series Duct Smoke Detector.
The detector shall be UL listed per UL S911, standard
for Smoke Detectors for Duct Applications, specifically
for use in air handling systems. The detector shall operate at air velocities from 500 feet per minute to 4000
feet per minute. The detector shall have an operating
temperature range of 32˚F to 158˚F. The detector housing
shall be equipped with an integral mounting base capable
of accommodating ionization detector heads. It shall be
capable of local testing via magnetic switch or remote test-
ing using the RTS451KEY or RTS451 Remote Test Station.
The duct detector housing shall incorporate an airtight
smoke chamber in compliance with UL S911. The housing
shall be capable of mounting to rectangular or round ducts
up to 12′ wide without adapter brackets. An integral filter
system shall be included to reduce dust and residue effects
on detector and housing, thereby reducing maintenance
and servicing. Sampling tubes shall be installed after the
housing is mounted to the duct by passing through the duct
housing. Terminal connections shall be of the strip and
clamp method suitable for 14–18 AWG wiring.
Electrical Specifications
Power Supply Voltage
20 - 29 VDC
24 VAC 50 - 60 Hz
120 VAC 50 - 60 Hz
220/240 VAC 50 - 60 Hz
CURRENT REQUIREMENTS (USING NO ACCESSORIES)
Max. standby current
25 mA
35 mA RMS
20 mA RMS
20 mA RMS
Max. alarm current
95 mA
55 mA RMS
55 mA RMS
30 mA RMS
CONTACT RATINGS
Accessory Current Loads at 24 VDC
Alarm initiation contacts (SPST)
2.0A @ 30 VAC/DC (0.6 power factor)
Device
Standby
Alarm
Alarm auxiliar y contacts (DPDT)
10A @ 30 VDC
AP451
12mA max.
30mA max.
10A @ 250 VAC
PA400W
0mA max.
15mA max.
0.3 @32 VDC (resistive)
RA400Z
0mA max.
7mA max.
RTS451
0mA max.*
8mA max.
RTS451KEY
12mA max.*
8mA max.
Trouble contacts (SPST)
*NOTE: When initiating an alarm, the RTS451 and RTS451KEY require 103mA in alarm. Nominal standby
current is 0mA. Alarm current is 8 mA maximum when test magnet is removed.
NOTE: Accessories are only rated to 120°F and must be installed indoors.
ANY COMBINATION OF ACCESSORIES MAY BE USED SUCH THAT THE
GIVEN CURRENT LOADS TOTAL:
100mA OR LESS IN THE STANDBY STATE,
150mA OR LESS IN THE ALARM STATE.
Physical Specifications
Length:
14.5 inches (36.8 cm)
Weight:
4.5 lbs. (2.0 kg)
Air Duct Velocity:
500 to 4000 ft./min.
Width:
5 inches (12.7 cm)
Operating Temperature Range:
32º to 158ºF (0º to 70ºC)
Operating Humidity Range:
10% to 93% relative humidity
Depth:
4 inches (10.2 cm)
Storage Temperature Range:
–22º to 158ºF (–30º to 70ºC)
Voltage:
24 VAC/VDC or 120/220 VAC
Ordering Information
Model
Description
DH400ACDCIHT
4-wire ionization high-temperature duct
RTS451KEY
Remote test station with key
smoke detector
RTS451
Remote test station
Replacement ionization high-temperature
PA400W
Piezo sounder (white)
sensor head
PS24LOW
Add-on strobe (white)
ST-1.5
Metal sampling tube duct widths 1′–2′
RA400Z
Remote annunciator alarm LED
ST-3
Metal sampling tube duct widths 2′–4′
CRT400
Ion cover removal tool
ST-5
Metal sampling tube duct widths 4′–8′
F36-05-00
Replacement air filters (two per package)
ST-10
Metal sampling tube duct widths 8′–12′
MOD400R
Sensitivity test module
P48-21-00
End cap for metal sampling tubes
M02-04-00
Test magnet
APA451
Annunciator with piezo alarm and power LEDs
RS14
Ion replacement screen
DH400OE-1
Weatherproof Outdoor Enclosure
A2650-01
Replacement installation kit (mounting hardware)
1451DHHT
System Sensor Sales and Service
System Sensor Headquarters
3825 Ohio Avenue
St. Charles, IL 60174
Ph: 800/SENSOR2
Fx: 630/377-6495
www.systemsensor.com
System Sensor Canada
Ph: 905.812.0767
Fx: 905.812.0771
System Sensor in China
Ph: 86.29.8832.0119
Fx: 86.29.8832.5110
System Sensor – Far East
Ph: 85.22.191.9003
Fx: 85.22.736.6580
System Sensor – India
Ph: 91.124.637.1770 x.2700
Fx: 91.124.637.3118
System Sensor Europe
Ph: 44.1403.891920
Fx: 44.1403.891921
System Sensor in Singapore
Ph: 65.6273.2230
Fx: 65.6273.2610
System Sensor – Australia
Ph: 613.54.281.142
Fx: 613.54.281.172
System Sensor – Russia
Ph: 70.95.937.7982
Fx: 70.95.937.7983
­© 2003 System Sensor. The company reserves the right to change product specifications without notice.
A05-0953-002•10/03•#1169
Similar pages