SEMICONDUCTOR TECHNICAL DATA ! The MC74LVQ08 is a high performance, quad 2–input AND gate operating from a 2.7 to 3.6V supply. High impedance TTL compatible inputs significantly reduce current loading to input drivers while TTL compatible outputs offer improved switching noise performance. LVQ Current drive capability is 12mA at the outputs. • Designed for 2.7 to 3.6V VCC Operation – Ideal for Low Power/Low Noise Applications LOW–VOLTAGE CMOS QUAD 2–INPUT AND GATE • Guaranteed Simultaneous Switching Noise Level and Dynamic Threshold Performance • Guaranteed Skew Specifications • Guaranteed Incident Wave Switching into 75Ω • Low Static Supply Current (10µA) Substantially Reduces System Power D SUFFIX PLASTIC SOIC CASE 751A–03 14 Requirements 1 • Latchup Performance Exceeds 500mA • ESD Performance: Human Body Model >2000V M SUFFIX PLASTIC SOIC EIAJ CASE 965–01 14 Pinout: 14–Lead (Top View) VCC 14 1 A2 B2 O2 A3 B3 O3 13 12 11 10 9 8 1 SD SUFFIX PLASTIC SSOP CASE 940A–03 1 DT SUFFIX PLASTIC TSSOP CASE 948G–01 14 1 2 3 4 5 6 7 A0 B0 O0 A1 B1 O1 GND 14 LOGIC DIAGRAM A0 B0 A1 B1 A2 B2 A3 B3 PIN NAMES 1 3 2 O0 4 6 5 O1 13 11 12 O2 Pins Function An, Bn On Data Inputs Outputs FUNCTION TABLE INPUTS 10 8 9 An Bn On L L H H L H L H L L L H O3 1/96 Motorola, Inc. 1996 1 OUTPUTS REV 1 MC74LVQ08 ABSOLUTE MAXIMUM RATINGS* Symbol Parameter VCC DC Supply Voltage VI Value Condition Unit –0.5 to +7.0 V DC Input Voltage –0.5 ≤ VI ≤ VCC + 0.5V V VO DC Output Voltage –0.5 ≤ VO ≤ VCC + 0.5 Output in HIGH or LOW State V IIK DC Input Diode Current –20 VI = –0.5V mA +20 VI = VCC + 0.5V mA –20 VO = –0.5V mA +20 VI = VCC + 0.5V mA IOK DC Output Diode Current IO DC Output Source/Sink Current ±50 mA ICC DC Supply Current ±200 mA IGND DC Ground Current ±200 mA TSTG Storage Temperature Range –65 to +150 °C * Absolute maximum continuous ratings are those values beyond which damage to the device may occur. Exposure to these conditions or conditions beyond those indicated may adversely affect device reliability. Functional operation under absolute–maximum–rated conditions is not implied. RECOMMENDED OPERATING CONDITIONS Symbol Parameter VCC Supply Voltage VI Input Voltage VO Output Voltage TA Operating Free–Air Temperature ∆V/∆t Input Transition Rise or Fall Rate, VIN from 0.8V to 2.0V, VCC = 3.0V Min Typ Max Unit 2.0 3.3 3.6 V 0 VCC V 0 VCC V –40 +85 °C 0 125 mV/ns DC ELECTRICAL CHARACTERISTICS TA = –40°C to +85°C Symbol Characteristic Condition Min 2.0 VIH HIGH Level Input Voltage (Note 1) 2.7V ≤ VCC ≤ 3.6V, VO = 0.1V or VCC – 0.1V VIL LOW Level Input Voltage (Note 1) 2.7V ≤ VCC ≤ 3.6V, VO = 0.1V or VCC – 0.1V VOH HIGH Level Output Voltage VOL LOW Level Output Voltage II Input Leakage Current IOLD Minimum Dynamic Output Current (Note 2) IOHD ICC Quiescent Supply Current Max V 0.8 2.7V ≤ VCC ≤ 3.6V; IOH = –50µA VCC – 0.1 VCC = 2.7V; IOH = –12mA 2.2 VCC = 3.0V; IOH = –12mA 2.48 Unit V V 2.7V ≤ VCC ≤ 3.6V; IOL = 50µA 0.1 2.7V ≤ VCC ≤ 3.6V; IOL= 12mA 0.4 2.7V ≤ VCC ≤3.6V; VI= VCC, GND ±1.0 µA VCC = 3.6V; VOLD = 0.8V Max 36 mA VCC = 3.6V; VOHD = 2.0V Min –25 mA 2.7V ≤ VCC ≤3.6V; VI = VCC, GND 10 µA V 1. These values of VI are used to test DC electrical characteristics only. Functional test should use VIH ≥ 2.4V, VIL ≤ 0.5V. 2. Incident wave switching on transmission lines with impedances as low as 75Ω for commercial temperature range is guaranteed. Maximum test duration is 2ms, one output loaded at a time. MOTOROLA 2 LVQ DATA BR1478 MC74LVQ08 DYNAMIC SWITCHING CHARACTERISTICS (VCC = 3.3V) TA = +25°C Symbol Characteristic Condition VOLP Dynamic LOW Peak Voltage (Note 1) VOLV Dynamic LOW Valley Voltage (Note 1) VIHD VILD Min Typ Max Unit CL = 50pF, VIH = 3.3V, VIL = 0V 0.6 1.0 V CL = 50pF, VIH = 3.3V, VIL = 0V –0.5 –1.0 V High Level Dynamic Input Voltage (Note 2) Input–Under–Test Switching 0V to Threshold, f=1MHz 1.5 2.0 V Low Level Dynamic Input Voltage (Note 2) Input–Under–Test Switching 3.3V to Threshold, f=1MHz 1.5 0.8 V 1. Number of outputs defined as “n”. Measured with “n–1” outputs switching from HIGH–to–LOW. The remaining output is measured in the LOW state. 2. Number of data inputs is defined as “n” switching, “n–1” inputs switching 0V to 3.3V. AC CHARACTERISTICS (tR = tF = 2.5ns; CL = 50pF; RL = 500Ω) Limits TA = +25°C VCC = 3.0V to 3.6V Symbol tPLH tPHL Parameter Propagation Delay Input to Output TA = –40°C to +85°C VCC = 2.7V VCC = 3.0V to 3.6V VCC = 2.7V Min Typ Max Min Typ Max Min Max Max Unit 1.5 1.5 7.0 6.0 9.5 8.5 1.5 1.5 7.5 6.5 10.0 9.0 1.0 1.0 10.0 9.0 11.0 10.0 ns tOSHL Output–to–Output Skew 1.0 1.5 1.0 1.5 1.5 ns tOSLH (Note 1) 1.0 1.5 1.0 1.5 1.5 1. Skew is defined as the absolute value of the difference between the actual propagation delay for any two separate outputs of the same device. The specification applies to any outputs switching in the same direction, either HIGH–to–LOW (tOSHL) or LOW–to–HIGH (tOSLH); parameter guaranteed by design. CAPACITIVE CHARACTERISTICS Symbol Parameter CPD Power Dissipation Capacitance CIN Input Capacitance LCX DATA BR1478 Condition Typical Unit 10MHz, VCC = 3.3V, VI = 0V or VCC 22 pF VCC = Open, VI = 0V or VCC 4.5 pF 3 MOTOROLA MC74LVQ08 VCC An, Bn 50% VCC 50% VCC 0V tPLH tPHL VOH 50% VCC On 50% VCC VOL PROPAGATION DELAYS tR = tF = 2.5ns, 10% to 90%; f = 1MHz; tW = 500ns Figure 1. AC Waveforms VCC PULSE GENERATOR DUT RT CL RL CL = 50pF or equivalent (Includes jig and probe capacitance) RL = R1 = 500Ω or equivalent RT = ZOUT of pulse generator (typically 50Ω) Figure 2. Test Circuit MOTOROLA 4 LVQ DATA BR1478 MC74LVQ08 OUTLINE DIMENSIONS D SUFFIX PLASTIC SOIC PACKAGE CASE 751A–03 ISSUE F NOTES: 1. DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2. CONTROLLING DIMENSION: MILLIMETER. 3. DIMENSIONS A AND B DO NOT INCLUDE MOLD PROTRUSION. 4. MAXIMUM MOLD PROTRUSION 0.15 (0.006) PER SIDE. 5. DIMENSION D DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.127 (0.005) TOTAL IN EXCESS OF THE D DIMENSION AT MAXIMUM MATERIAL CONDITION. –A – 14 8 –B – 1 P7 PL 0.25 (0.010) 7 G D 0.25 (0.010) M T F B A S DIM A B C D F G J K M P R J M K 14 PL M R X 45° C SEATING PLANE B M S MILLIMETERS MIN MAX 8.75 8.55 4.00 3.80 1.75 1.35 0.49 0.35 1.25 0.40 1.27 BSC 0.25 0.19 0.25 0.10 7° 0° 5.80 6.20 0.25 0.50 INCHES MIN MAX 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 BSC 0.008 0.009 0.004 0.009 0° 7° 0.228 0.244 0.010 0.019 M SUFFIX PLASTIC SOIC EIAJ PACKAGE CASE 965–01 ISSUE O 14 NOTES: 1 DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2 CONTROLLING DIMENSION: MILLIMETER. 3 DIMENSIONS D AND E DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS AND ARE MEASURED AT THE PARTING LINE. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4 TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 5 THE LEAD WIDTH DIMENSION (b) DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE LEAD WIDTH DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT BE LOCATED ON THE LOWER RADIUS OR THE FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS AND ADJACENT LEAD TO BE 0.46 ( 0.018). LE 8 Q1 E HE M_ L 7 1 DETAIL P Z D e VIEW P A c b 0.13 (0.005) LCX DATA BR1478 A1 M 0.10 (0.004) 5 DIM A A1 b c D E e HE L LE M Q1 Z MILLIMETERS MIN MAX --2.05 0.05 0.20 0.35 0.50 0.18 0.27 9.90 10.50 5.10 5.45 1.27 BSC 7.40 8.20 0.50 0.85 1.10 1.50 10 _ 0_ 0.70 0.90 --1.42 INCHES MIN MAX --0.081 0.002 0.008 0.014 0.020 0.007 0.011 0.390 0.413 0.201 0.215 0.050 BSC 0.291 0.323 0.020 0.033 0.043 0.059 10 _ 0_ 0.028 0.035 --0.056 MOTOROLA MC74LVQ08 OUTLINE DIMENSIONS SD SUFFIX PLASTIC SSOP PACKAGE CASE 940A–03 ISSUE B 14X K REF 0.12 (0.005) T U M S V S NOTES: 6 DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 7 CONTROLLING DIMENSION: MILLIMETER. 8 DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 9 DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 10 DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION/INTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.13 (0.005) TOTAL IN EXCESS OF K DIMENSION AT MAXIMUM MATERIAL CONDITION. DAMBAR INTRUSION SHALL NOT REDUCE DIMENSION K BY MORE THAN 0.07 (0.002) AT LEAST MATERIAL CONDITION. 11 TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 12 DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE –W–. 0.25 (0.010) N 14 L/2 8 M N B L F PIN 1 IDENT 1 7 DETAIL E –U– A –V– 0.20 (0.008) M T U ÉÉÉÉ ÇÇÇÇ ÇÇÇÇ ÉÉÉÉ ÇÇÇÇ ÉÉÉÉ ÇÇÇÇ ÉÉÉÉ K J S J1 K1 SECTION N–N 0.076 (0.003) –T– –W– C SEATING PLANE DIM A B C D F G H J J1 K K1 L M D G DETAIL E H MILLIMETERS MIN MAX 6.07 6.33 5.20 5.38 1.73 1.99 0.05 0.21 0.63 0.95 0.65 BSC 1.08 1.22 0.09 0.20 0.09 0.16 0.25 0.38 0.25 0.33 7.65 7.90 0_ 8_ INCHES MIN MAX 0.238 0.249 0.205 0.212 0.068 0.078 0.002 0.008 0.024 0.037 0.026 BSC 0.042 0.048 0.003 0.008 0.003 0.006 0.010 0.015 0.010 0.013 0.301 0.311 0_ 8_ DT SUFFIX PLASTIC TSSOP PACKAGE CASE 948G–01 ISSUE O 14X K REF 0.10 (0.004) 0.15 (0.006) T U M T U V S NOTES: 1 DIMENSIONING AND TOLERANCING PER ANSI Y14.5M, 1982. 2 CONTROLLING DIMENSION: MILLIMETER. 3 DIMENSION A DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS. MOLD FLASH OR GATE BURRS SHALL NOT EXCEED 0.15 (0.006) PER SIDE. 4 DIMENSION B DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSION. INTERLEAD FLASH OR PROTRUSION SHALL NOT EXCEED 0.25 (0.010) PER SIDE. 5 DIMENSION K DOES NOT INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL BE 0.08 (0.003) TOTAL IN EXCESS OF THE K DIMENSION AT MAXIMUM MATERIAL CONDITION. 6 TERMINAL NUMBERS ARE SHOWN FOR REFERENCE ONLY. 7 DIMENSION A AND B ARE TO BE DETERMINED AT DATUM PLANE –W–. S S N 2X 14 L/2 0.25 (0.010) 8 M B –U– L PIN 1 IDENT. F 7 1 0.15 (0.006) T U N S DETAIL E ÉÉÉ ÇÇÇ ÇÇÇ ÉÉÉ ÇÇÇ ÉÉÉ ÇÇÇ ÉÉÉ K A –V– K1 J J1 SECTION N–N –W– C 0.10 (0.004) –T– SEATING PLANE MOTOROLA D G H DETAIL E 6 DIM A B C D F G H J J1 K K1 L M MILLIMETERS MIN MAX 4.90 5.10 4.30 4.50 ––– 1.20 0.05 0.15 0.50 0.75 0.65 BSC 0.50 0.60 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 BSC 0_ 8_ INCHES MIN MAX 0.193 0.200 0.169 0.177 ––– 0.047 0.002 0.006 0.020 0.030 0.026 BSC 0.020 0.024 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252 BSC 0_ 8_ LVQ DATA BR1478 MC74LVQ08 Motorola reserves the right to make changes without further notice to any products herein. Motorola makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Motorola assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. “Typical” parameters can and do vary in different applications. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. Motorola does not convey any license under its patent rights nor the rights of others. Motorola products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the Motorola product could create a situation where personal injury or death may occur. Should Buyer purchase or use Motorola products for any such unintended or unauthorized application, Buyer shall indemnify and hold Motorola and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Motorola was negligent regarding the design or manufacture of the part. Motorola and are registered trademarks of Motorola, Inc. Motorola, Inc. is an Equal Opportunity/Affirmative Action Employer. How to reach us: USA/EUROPE: Motorola Literature Distribution; P.O. Box 20912; Phoenix, Arizona 85036. 1–800–441–2447 JAPAN: Nippon Motorola Ltd.; Tatsumi–SPD–JLDC, Toshikatsu Otsuki, 6F Seibu–Butsuryu–Center, 3–14–2 Tatsumi Koto–Ku, Tokyo 135, Japan. 03–3521–8315 MFAX: [email protected] –TOUCHTONE (602) 244–6609 INTERNET: http://Design–NET.com HONG KONG: Motorola Semiconductors H.K. Ltd.; 8B Tai Ping Industrial Park, 51 Ting Kok Road, Tai Po, N.T., Hong Kong. 852–26629298 ◊ LCX DATA BR1478 7 *MC74LVQ08/D* MC74LVQ08/D MOTOROLA