F-217 IDMD–24–D–12.00–G (2.54 mm) .100" SLIM BODY FLAT RIBBON IDC CABLES SPECIFICATIONS For complete specifications see www.samtec.com?IDSS, www.samtec.com?IDSD, www.samtec.com?IDMS or www.samtec.com?IDMD Insulator Material: Black Glass Filled Polyester Plating: Au over 50 µ" (1.27 µm) Ni or Sn over 100 µ" (2.54 µm) Cu or 50 µ" (1.27 µm) Ni Wire: 28 AWG 7/36 stranded Tinned Copper Temperature Range: -20 °C to +105 °C (Rainbow Cable) -40 °C to +105 °C (Gray Cable) Contact (IDSS/IDSD): BeCu Terminal (IDMS/IDMD): Phosphor Bronze Current Rating (IDSD/TST): 3.4 A per pin (1 position powered per row) Current Rating (IDMD): 3 A per pin (1 position powered per row) Contact Resistance: 15 mW Lead Size Range: (0.56 mm) .022" SQ to (0.71 mm) .028" SQ Lead Insertion Depth: (5.59 mm) .220" to (6.22 mm) .245" RoHS Compliant: Yes Mates with: TSW, MTSW, TSM, EJH, PHT, HMTSW, HTSW, HW, DW, EW, ZW, MTLW TYPE STRIP IDSD Mates with: TST, HTST, ZST, BST, EJH NO. PINS PER ROW S –S = Single End D = Double (Color coded cable N/A for 31 thru 36 pins/row. See –G option.) IDM = Standard Tail Male Plug IDS = Socket Socket or Male Plug on one end –D = Double End –02 thru –32 DOUBLE Full size (64 positions): (82.55) 3.250 Less than 64 positions: No. Positions/row X (2.54) .100 + (1.68) .066 IDMD (Double) IDMS (Single) Socket or Male Plug on each end SINGLE Full size (32 positions): (81.53) 3.210 Less than 32 positions: No. Positions/row X (2.54) .100 + (0.71) .028 (2.54) .100 –T = Transfer End (5.08) .200 (6.10) .240 MAX (0.48) .019 (0.46) .018 x (0.48) .019 (3.18) .125 (2.54) .100 (2.54) .100 Male Plug on one end with socket on other. Begin part number with IDM. (For square or long tail see HCMX Series) FILE NO. E111594 OTHER SOLUTIONS –02 thru –36 DOUBLE Full size (72 positions): (92.71) 3.650 Less than 72 positions: No. Positions/row x (2.54) .100 + (1.50) .059 SINGLE Full size (36 positions): (91.69) 3.610 Less than 36 positions: No. Positions/row x (2.54) .100 + (0.48) .019 IDSS (Single) Molded-To-Position IDC Assemblies IDSD (Double) (5.08) .200 (9.27) .365 REF (2.54) .100 Note: This Series is non-standard, non-returnable. END ASSEMBLY = Single RECOGNITIONS For complete scope of recognitions see www.samtec.com/quality ROW OPTION (0.76) .030 SQ (2.54) .100 WWW.SAMTEC.COM Due to technical progress, all designs, specifications and components are subject to change without notice. • • • • • Low profile Skinny side locks Dual beam contacts Single and double row (3.05 mm) .120" and (5.84 mm) .230" length tail available Call Samtec for HCXX Series. IDSD–05–D–04.25–S02 IDSD–24–S–05.00 IDSS, IDSD, IDMS, IDMD SERIES ASSEMBLED LENGTH EJECTOR HEADERS & LOCKING CLIPS OPTION IDSS or IDSD STRIP ASSEMBLY – “XX.XX” POLARIZING KEY = Assembled Length (0.64) .025 SQ Assembled Length in INCHES (±1/8" ) (2 inches minimum) (5.84) .230 • Locking clips LOCKING CLIP Optional polarizing key for use with IDSS & IDSD Series. Also polarizes SSW, SSQ, ESW & ESQ Series. Black High Temperature Thermoplastic .025" SQ TERMINAL STRIP (TSW) PC BOARD See TSW Series. Order: Part Number PK-01-06 (Available in wheels of six each) Plating –T = Tin (Both ends) See EJH Series. –ST “X” –S “XX” = Stripped & Tinned Tin IDM µ" (0.25 µm) Gold IDS –C = 10 (-T End Assembly Required) Specify Suffix from table. All dimensions are ± 1/16". Not available in 28 positions and higher. “XX” ± 1⁄8" 2" min. (-T End Assembly Required) 1 –ST8 –ST4 –ST2 –ST3 1/8" (3.18) 1/4" (6.35) 1/2" (12.70) 3/8" (9.53) 4 01 2 –M = Middle Reversed 7 –D “XX” Specify “XX” as number of conductors to be broken out. Specify “XX” as position. For Double the same position will be polarized on both ends. (Not available on IDM unless transfer, then only the socket is polarized.) 8 = Daisy Chain, Double = Breakout 03 When mating double row connector with two single row connectors, the outer most single will be connected to Conductor #1 and the inside single to Conductor #2. 02 –B “XX” 71 Single Row Connectors (IDSS) 4" minimum =Polarized 04 = Reversed Outer Most –P “XX” 72 –R = Daisy Chain Single –A = 10Tinµ"IDS(0.25 µm) Gold IDM Standard plating is selective gold over BeCu contact for IDS; Selective gold over phosphor bronze for IDM. • Ejector headers “XX” ± 1⁄8" 2" min. Requires –SXX, –WXX or –DXX Double Row Connectors (IDSD or IDMD) 8 –O Outer Most “XX” = Outside Reversed 4" minimum –G 5"max. 2"min. = Gray Cable Breakout starts with Number 1 lead indicated by brown wire or red stripe. Shown on top side. Specify –G for Gray cable. Gray cable has one red edge. IDSS and IDMS uses .100" centerline cable. IDSD and IDMD uses .050" centerline cable. Cable is 28 AWG 7/36 copper wire. Standard cable is same as above except color coded. 7 –W “XX” –RW Same as –S “XX” except outer strip connected to Conductor #2 and inside strip connected to Conductor #1. = Reversed Wiring #1 wire opposite position #1. 3 = Wiring Reversed Daisy Chain, Single 5 6 Requires –SXX, –WXX or –DXX 7 WWW.SAMTEC.COM Due to technical progress, all designs, specifications and components are subject to change without notice. 8