MICROCIRCUIT DATA SHEET Original Creation Date: 01/20/00 Last Update Date: 09/17/03 Last Major Revision Date: 07/18/02 MRLM101A-X-RH REV 1B2 SINGLE OPERATIONAL AMPLIFIER - EXTERNALLY COMPENSATED: ALSO AVAILABLE GUARANTEED TO 100k rd(Si) TESTED TO MIL-STD-883, METHOD 1019 General Description The LM101A is a general purpose operational amplifier which features improved performance over industry standards such as the LM709. Advanced processing techniques make possible an order of magnitude reduction in input currents, and a redesign of the biasing circuitry reduces the temperature drift of input current. This amplifier offers many features which make its application nearly foolproof: overload protection on the input and output, no latch-up when the common mode range is exceeded, and freedom from oscillations and compensation with a single 30 pF capacitor. It has advantages over internally compensated amplifiers in that the frequency compensation can be tailored to the particular application. For example, in low frequency circuits it can be overcompensated for increased stability margin. Or the compensation can be optimized to give more than a factor of ten improvement in high frequency performance for most applications. In addition, the device provides better accuracy and lower noise in high impedance circuitry. The low input currents also make it particularly well suited for long interval integrators or timers, sample and hold circuits and low frequency waveform generators. Further, replacing circuits where matched transistor pairs buffer the inputs of conventional IC op amps, it can give lower offset voltage and a drift at a lower cost. Industry Part Number NS Part Numbers LM101A LM101AH-QMLV LM101AHRQMLV LM101AJ-QMLV LM101AW-QMLV LM101AWRQMLV Prime Die LM101A Controlling Document SEE FEATURES SECTION Processing Subgrp Description MIL-STD-883, Method 5004 1 2 3 4 5 6 7 8A 8B 9 10 11 Quality Conformance Inspection MIL-STD-883, Method 5005 1 Static tests at Static tests at Static tests at Dynamic tests at Dynamic tests at Dynamic tests at Functional tests at Functional tests at Functional tests at Switching tests at Switching tests at Switching tests at Temp ( oC) +25 +125 -55 +25 +125 -55 +25 +125 -55 +25 +125 -55 MICROCIRCUIT DATA SHEET MRLM101A-X-RH REV 1B2 Features - Offset voltage 3 mV maximum over temperature Input current 100 nA maximum over temperature Offset current 20 nA maximum over temperature Guaranteed drift characteristics Offsets guaranteed over entire common mode and supply voltage ranges Slew rate of 10V/us as a summing amplifier CONTROLLING DOCUMENTS: LM101AH-QMLV 5962-9951501VGA LM101AHRQMLV 5962R9951501VGA LM101AJ-QMLV 5962-9951501VPA LM101AW-QMLV 5962-9951501VHA LM101AWRQMLV 5962R9951501VHA 2 MICROCIRCUIT DATA SHEET MRLM101A-X-RH REV 1B2 (Absolute Maximum Ratings) (Note 1) Supply Voltage +22V Differential Input Voltage +30V Input Voltage (Note 3) +15V Ouput Short Circuit Duration (Note 2) Continuous Operating Ambient Temp. Range -55 C < Ta < +125 C Maximum Junction Temperature 150 C Power Dissipation at TA = 25 C (Note 2) H-Pkg (Still Air) H-Pkg (500LF/Min Air Flow) J-Pkg (Still Air) J-Pkg (500LF/Min Air Flow) Thermal Resistance ThetaJA H-Pkg (Still Air) H-Pkg (500LF/Min Air Flow) J-Pkg (Still Air) J-Pkg (500LF/Min Air Flow) 750mW 1200mW 1000mW 1500MW 165 89 128 75 ThetaJC H-Pkg J-Pkg Storage Temperature Range C/W C/W C/W C/W 39 C/W 26 C/W -65 C <Ta< +150 C Lead Temperature (Soldering, 10 seconds) ESD Tolerance (Note 4) 300 C 3500V Note 1: Note 2: Note 3: Note 4: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Some performance characteristics may degrade when the device is not operated under the listed test conditions. The maximum power dissipation must be derated at elevated temperatures and is dictated by Tjmax (maximum junction temperature), ThetaJA (package junction to ambient thermal resistance), and TA (ambient temperature). The maximum allowable power dissipation at any temperature is Pdmax = (Tjmax - TA)/ThetaJA or the number given in the Absolute Maximum Ratings, whichever is lower. For supply voltages less than +15V, the absolute maximum input voltage is equal to the supply voltage. Human body model, 100 pF discharged through 1.5k Ohms. 3 MICROCIRCUIT DATA SHEET MRLM101A-X-RH REV 1B2 Electrical Characteristics DC PARAMETERS: See NOTE 3 (The following conditions apply to all the following parameters, unless otherwise specified.) DC: +Vcc = +20V, Vcm = 0V, Rs = 50 ohms SYMBOL Vio PARAMETER Input Offset Voltage CONDITIONS NOTES +Vcc = 35V, -Vcc = -5V, Vcm = -15V +Vcc = 5V, -Vcc = -35V, Vcm = +15V Vcm = 0V +Vcc = 5V, -Vcc = -5V, Vcm = 0V Iio Input Offset Current +Vcc = 35V, -Vcc = -5V, Vcm = -15V, Rs = 100K Ohms +Vcc = 5V, -Vcc = -35V, Vcm = +15V, Rs = 100K Ohms Vcm = 0V, Rs = 100K Ohms +Vcc = 5V, -Vcc = -5V, Vcm = 0V, Rs = 100K Ohms Iib+ Input Bias Current +Vcc = 35V, -Vcc = -5V, Vcm = -15V, Rs = 100K Ohms +Vcc = 5V, -Vcc = -35V, Vcm = +15V, Rs = 100K Ohms Vcm = 0V, Rs = 100K Ohms +Vcc = 5V, -Vcc = -5V, Vcm = 0V, Rs = 100K Ohms 4 PINNAME MIN MAX UNIT SUBGROUPS -2 +2 mV 1 -3 +3 mV 2, 3 -2 +2 mV 1 -3 +3 mV 2, 3 -2 +2 mV 1 -3 +3 mV 2, 3 -2 +2 mV 1 -3 +3 mV 2, 3 -10 +10 nA 1, 2 -20 +20 nA 3 -10 +10 nA 1, 2 -20 +20 nA 3 -10 +10 nA 1, 2 -20 +20 nA 3 -10 +10 nA 1, 2 -20 +20 nA 3 -0.1 75 nA 1, 2 -0.1 100 nA 3 -0.1 75 nA 1, 2 -0.1 100 nA 3 -0.1 75 nA 1, 2 -0.1 100 nA 3 -0.1 75 nA 1, 2 -0.1 100 nA 3 MICROCIRCUIT DATA SHEET MRLM101A-X-RH REV 1B2 Electrical Characteristics DC PARAMETERS: See NOTE 3(Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) DC: +Vcc = +20V, Vcm = 0V, Rs = 50 ohms SYMBOL Iib- PARAMETER Input Bias Current CONDITIONS NOTES +Vcc = 35V, -Vcc = -5V, Vcm = -15V, Rs = 100K Ohms +Vcc = 5V, -Vcc = -35V, Vcm = +15V, Rs = 100K Ohms Vcm = 0V, Rs = 100K Ohms +Vcc = 5V, -Vcc = -5V, Vcm = 0V, Rs = 100K Ohms +PSRR -PSRR Power Supply Rejection Ratio Power Supply Rejection Ratio +Vcc = 10V, -Vcc = -20V +Vcc = 20V, -Vcc = -10V CMRR Common Mode Rejection Ratio Vcc = +35V to +5V, Vcm = +15V VioADJ(+) Adjustment for Input Offset Voltage VioADJ(-) Adjustment for Input Offset Voltage Ios+ Output Short Circuit Current +Vcc = 15V, -Vcc = -15V, t < 25mS, Vcm = -15V Ios- Output Short Circuit Current +Vcc = 15V, -Vcc = -15V, t <25mS, Vcm = +15V Icc Power Supply Current +Vcc = 15V, -Vcc = -15V PINNAME MIN MAX UNIT SUBGROUPS -0.1 75 nA 1, 2 -0.1 100 nA 3 -0.1 75 nA 1, 2 -0.1 100 nA 3 -0.1 75 nA 1, 2 -0.1 100 nA 3 -0.1 75 nA 1, 2 -0.1 100 nA 3 -50 +50 uV/V 1 -100 +100 uV/V 2, 3 -50 +50 uV/V 1 -100 +100 uV/V 2, 3 80 dB 1, 2, 3 4 mV 1, 2, 3 mV 1, 2, 3 mA 1, 2, 3 +60 mA 1, 2, 3 3 mA 1 2.32 mA 2 3.5 mA 3 -4 -60 Delta Vio/Delta T Temperature Coefficient of Input Offset Voltage +25 C < TA < +125 C 1 -15 +15 uV/ C 2 +25 C < TA < -55 C 1 -18 +18 uV/ C 3 Delta Iio/Delta T Temperature Coefficient of Input Offset Current +25 C < TA < +125 C 1 -100 +100 pA/ C 2 +25 C < TA < -55 C 1 -200 +200 pA/ C 3 5 MICROCIRCUIT DATA SHEET MRLM101A-X-RH REV 1B2 Electrical Characteristics DC PARAMETERS: See NOTE 3(Continued) (The following conditions apply to all the following parameters, unless otherwise specified.) DC: +Vcc = +20V, Vcm = 0V, Rs = 50 ohms SYMBOL Avs- PARAMETER Large Signal (Open Loop) Voltage Gain CONDITIONS NOTES Rl = 2K Ohms, Vout = -15V Large Signal (Open Loop) Voltage Gain Vop+ Vop- Large Signal (Open Loop) Voltage Gain Output Voltage Swing Output Voltage Swing MAX UNIT SUBGROUPS 50 V/mV 4 2 25 V/mV 5, 6 2 50 V/mV 4 2 25 V/mV 5, 6 2 50 V/mV 4 2 25 V/mV 5, 6 2 50 V/mV 4 2 25 V/mV 5, 6 Vcc = +5V, Rl = 2K Ohms, Vout = +2V 2 10 V/mV 4, 5, 6 Vcc = +5V, Rl = 10K Ohms, Vout = +2V 2 10 V/mV 4, 5, 6 Rl = 10K Ohms, Vcm = -20V +16 V 4, 5, 6 Rl = 2K Ohms, Vcm = -20V +15 V 4, 5, 6 Rl = 2K Ohms, Vout = +15V Rl = 10K Ohms, Vout = +15V Avs MIN 2 Rl = 10K Ohms, Vout = -15V Avs+ PINNAME Rl = 10K Ohms, Vcm = 20V -16 V 4, 5, 6 Rl = 2K ohms, Vcm = 20V -15 V 4, 5, 6 AC PARAMETERS: See NOTE 3 (The following conditions apply to all the following parameters, unless otherwise specified.) AC: +Vcc = +20V, Vcm = 0V, Rs = 50 Ohms Sr+ Sr- Slew Rate Slew Rate Av = 1, Vin = -5V to +5V Av = 1, Vin = +5V to -5V 0.3 V/uS 7, 8A 0.2 V/uS 8B 0.3 V/uS 7, 8A 0.2 V/uS 8B TR(tr) Rise Time Av = 1, Vin = 50mV 800 nS 7, 8A, 8B TR(os) Overshoot Av = 1, Vin = 50mV 25 % 7 35 % 8A, 8B NI(BB) Noise Broadband BW = 10Hz to 5KHz, Rs = 0 Ohms 15 uVrms 7 NI(PC) Noise Popcorn BW = 10Hz to 5KHz, Rs = 100K Ohms 80 uVpk 7 6 MICROCIRCUIT DATA SHEET MRLM101A-X-RH REV 1B2 Electrical Characteristics DC PARAMETERS: DRIFT VALUES (The following conditions apply to all the following parameters, unless otherwise specified.) DC: +Vcc = +20V, Vcm = 0V, Rs = 50 Ohms. "Delta calculations performed on JAN S and QMLV devices at group B, subgroup 5 only". SYMBOL PARAMETER CONDITIONS NOTES PINNAME MIN MAX UNIT SUBGROUPS Vio Input Offset Voltage Vcm = 0V -0.5 0.5 mV 1 Iib+ Input Bias Current Vcm = 0V, Rs = 100K Ohms -7.5 7.5 nA 1 Iib- Input Bias Current Vcm = 0V, Rs = 100K Ohms -7.5 7.5 nA 1 Note 1: Note 2: Note 3: Calculated parameter. Datalog reading of K = V/mV. Pre and post irradiation limits are identical to those listed under AC and DC electrical characteristics except as listed in the Post Radiation Limits Table. These parts may be dose rate sensitive in a space environment and demonstrate enhanced low dose rate effect. Radiation end point limits for the noted parameters are guaranteed only for the conditions as specified in MIL-STD-883, Method 1019.5 7 MICROCIRCUIT DATA SHEET MRLM101A-X-RH REV 1B2 Graphics and Diagrams GRAPHICS# DESCRIPTION 05309HRB2 CERDIP (J), 14 LEAD (B/I CKT) 08337HRB2 CERPACK (W), 10 LEAD (B/I CKT) 09384HRA4 METAL CAN, (H) TO-99,8 LEAD,.200 DIA P.C.(B/I CKT) 09413HRB1 CERDIP (J), 8 LEAD (B/I CKT) H08CRF METAL CAN (H), TO-99, 8LD .200 DIA P.C. (P/P DWG) J08ARL CERDIP (J), 8 LEAD (P/P DWG) P000178A METAL CAN (H), 8 LEAD (PINOUT) P000180A CERPACK (W), 10 LEAD (PINOUT) P000226A CERDIP (J), 8 LEAD (PINOUT) W10ARG CERPACK (W), 10 LEAD (P/P DWG) See attached graphics following this page. 8 N N N MICROCIRCUIT DATA SHEET MRLM101A-X-RH REV 1B2 Revision History Rev ECN # Originator Changes 0A0 M0003656 05/08/00 Rel Date Rose Malone Initial MDS Release: MRLM101A-X-RH, Rev. 0A0 0B0 M0003678 04/08/02 Rose Malone Update MDS: MRLM101A-X-RH, Rev. 0A0 to MRLM101A-X-RH, Rev. 0B0. Typo error in Features Section Controlling Documents: SMD Suffix VPA should be QPA for LM101AJRQML. 0C0 M0003990 08/13/02 Rose Malone Update MDS: MRLM101A-X-RH, Rev. 0B0 to MRLM101A-X-RH, Rev. 0C0. Deleted reference for the following NSID's from Main Table, Features Section and Graphics Section. LM101AHRQML , LM101AJRQML, LM101AJRQMLV, LM101AWRQML, LM101AWRQMLV product un-available. 1A1 M0004032 09/17/03 Rose Malone Update MRLM101A-X-RH, Rev. 0C0 to MRLM101A-X-RH, Rev. 1A1. Added to Main Table and Features Section NSID's LM101AH-QMLV and LM101AJ-QMLV, to Absolute Section J pkg Thermal Resistance information and Graphics Section J pkg Mkt Dwg, B/I Ckt, Pin Out. Created QMLV NSID's to Replace the JL101 Space Level Products. Changed Electrical Section AC Parameter TR(os) Subgroups 8A, 8B from 25% to 35%. Subgroups 8A, 8B unable to meet 25% Overshoot. 1B2 M0004301 09/17/03 Rose Malone Update MD: MRLM101A-X-RH, Rev. 1A1 to MRLM101A-X-RH, Rev. 1B2. Added W package reference to Main Table, Features Section and Graphics Section. Changed ESD Rating from 2000V to 3500V. 9