LM193,LM2903,LM293,LM393 LM193/LM293/LM393/LM2903 Low Power Low Offset Voltage Dual Comparators Literature Number: SNOSBJ6D LM193/LM293/LM393/LM2903 Low Power Low Offset Voltage Dual Comparators General Description Advantages The LM193 series consists of two independent precision voltage comparators with an offset voltage specification as low as 2.0 mV max for two comparators which were designed specifically to operate from a single power supply over a wide range of voltages. Operation from split power supplies is also possible and the low power supply current drain is independent of the magnitude of the power supply voltage. These comparators also have a unique characteristic in that the input common-mode voltage range includes ground, even though operated from a single power supply voltage. n n n n n n Application areas include limit comparators, simple analog to digital converters; pulse, squarewave and time delay generators; wide range VCO; MOS clock timers; multivibrators and high voltage digital logic gates. The LM193 series was designed to directly interface with TTL and CMOS. When operated from both plus and minus power supplies, the LM193 series will directly interface with MOS logic where their low power drain is a distinct advantage over standard comparators. The LM393 and LM2903 parts are available in National’s innovative thin micro SMD package with 8 (12 mil) large bumps. Squarewave Oscillator High precision comparators Reduced VOS drift over temperature Eliminates need for dual supplies Allows sensing near ground Compatible with all forms of logic Power drain suitable for battery operation Features n Wide supply — Voltage range: 2.0V to 36V ± 1.0V to ± 18V — Single or dual supplies: n Very low supply current drain (0.4 mA) — independent of supply voltage n Low input biasing current: 25 nA ± 5 nA n Low input offset current: ± 3 mV n Maximum offset voltage: n Input common-mode voltage range includes ground n Differential input voltage range equal to the power supply voltage n Low output saturation voltage,: 250 mV at 4 mA n Output voltage compatible with TTL, DTL, ECL, MOS and CMOS logic systems n Available in the 8-Bump (12 mil) micro SMD package n See AN-1112 for micro SMD considerations Non-Inverting Comparator with Hysteresis 00570909 00570938 © 2002 National Semiconductor Corporation DS005709 www.national.com LM193/LM293/LM393/LM2903 Low Power Low Offset Voltage Dual Comparators August 2002 LM193/LM293/LM393/LM2903 Schematic and Connection Diagrams 00570902 Metal Can Package Dual-In-Line/SOIC Package 00570901 00570903 micro SMD micro SMD Marking 00570945 Top View 00570946 Top View www.national.com 2 LM193/LM193A (Note 10) LM2903 If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. Supply Voltage, V+ 36V Differential Input Voltage (Note 8) 36V Input Voltage −40˚C to +85˚C Storage Temperature Range −65˚C to +150˚C Lead Temperature (Soldering, 10 seconds) +260˚C Soldering Information −0.3V to +36V Input Current (VIN < −0.3V) (Note 3) −55˚C to +125˚C Dual-In-Line Package 50 mA Soldering (10 seconds) Power Dissipation (Note 1) 260˚C Small Outline Package Molded DIP 215˚C 780 mW Vapor Phase (60 seconds) Metal Can 660 mW Infrared (15 seconds) Small Outline Package 510 mW micro SMD Pacakge See AN-450 “Surface Mounting Methods and Their Effect on Product Reliability” for other methods of soldering surface mount devices. 568mW Output Short-Circuit to Ground (Note 2) 220˚C ESD rating Continuous (1.5 kΩ in series with 100 pF) Operating Temperature Range LM393 0˚C to +70˚C LM293 −25˚C to +85˚C 1300V Electrical Characteristics (V+ =5V, TA = 25˚C, unless otherwise stated) Parameter Conditions LM193A Min Units Typ Max Input Offset Voltage (Note 9) 1.0 2.0 mV Input Bias Current IIN(+) or IIN(−) with Output In Linear 25 100 nA 25 nA Range, VCM = 0V (Note 5) Input Offset Current IIN(+)−IIN(−) VCM = 0V Input Common Mode 3.0 V+ = 30V (Note 6) + 0 V −1.5 V Voltage Range RL = ∞ Supply Current V+ =5V 0.4 1 mA V+ =36V 1 2.5 mA RL≥15 kΩ, V+ =15V Voltage Gain 50 200 V/mV 300 ns VO = 1V to 11V Large Signal Response VIN =TTL Logic Swing, VREF =1.4V Time VRL =5V, RL =5.1 kΩ Response Time VRL =5V, RL =5.1 kΩ (Note 7) Output Sink Current VIN(−)=1V, VIN(+)=0, VO≈1.5V Saturation Voltage VIN(−)=1V, VIN(+)=0, ISINK≤4 mA 250 Output Leakage Current VIN(−)=0, VIN(+)=1V, VO =5V 0.1 6.0 1.3 µs 16 mA 400 mV nA Electrical Characteristics (V+ =5V, TA = 25˚C, unless otherwise stated) Parameter Input Offset Voltage Input Bias Current Conditions LM193 LM293, LM393 LM2903 Units Min Typ Max Min Typ Max Min Typ Max (Note 9) 1.0 5.0 1.0 5.0 2.0 7.0 mV IIN(+) or IIN(−) with Output In 25 100 25 250 25 250 nA 3.0 25 5.0 50 5.0 50 nA V+−1.5 V Linear Range, VCM = 0V (Note 5) Input Offset Current IIN(+)−IIN(−) VCM = 0V Input Common Mode V+ = 30V (Note 6) 0 V+−1.5 0 V+−1.5 0 Voltage Range 3 www.national.com LM193/LM293/LM393/LM2903 Absolute Maximum Ratings LM193/LM293/LM393/LM2903 Electrical Characteristics (Continued) (V+ =5V, TA = 25˚C, unless otherwise stated) Parameter Conditions LM193 Min Typ Supply Current Voltage Gain RL = ∞ LM293, LM393 Max Min Typ LM2903 Max Min Typ Units Max V+ =5V 0.4 1 0.4 1 0.4 1.0 mA V+ =36V 1 2.5 1 2.5 1 2.5 mA RL≥15 kΩ, V+ =15V 50 200 50 200 25 100 V/mV 300 ns VO = 1V to 11V Large Signal Response VIN =TTL Logic Swing, VREF =1.4V Time VRL =5V, RL =5.1 kΩ Response Time VRL =5V, RL =5.1 kΩ (Note 7) Output Sink Current VIN(−)=1V, VIN(+)=0, VO≤1.5V 300 300 1.3 6.0 1.3 16 6.0 Saturation Voltage VIN(−)=1V, VIN(+)=0, ISINK≤4 mA 250 Output Leakage Current VIN(−)=0, VIN(+)=1V, VO =5V 0.1 16 400 1.5 µs 16 mA 6.0 250 400 250 0.1 400 mV 0.1 nA Electrical Characteristics (V+ = 5V) (Note 4) Parameter Conditions LM193A Min Input Offset Voltage Units Typ Max (Note 9) 4.0 mV Input Offset Current IIN(+)−IIN(−), VCM =0V 100 nA Input Bias Current IIN(+) or IIN(−) with Output in Linear Range, 300 nA V+−2.0 V VCM =0V (Note 5) Input Common Mode Voltage Range V+ =30V (Note 6) Saturation Voltage VIN(−)=1V, VIN(+)=0, ISINK≤4 mA 700 mV Output Leakage Current VIN(−)=0, VIN(+) =1V, VO =30V 1.0 µA Differential Input Voltage Keep All VIN’s≥0V (or V−, if Used), (Note 8) 36 V 0 Electrical Characteristics (V+ = 5V) (Note 4) Parameter Conditions LM193 Min Typ LM293, LM393 Max Min Typ Max LM2903 Min Typ Units Max Input Offset Voltage (Note 9) 9 9 9 15 mV Input Offset Current IIN(+)−IIN(−), VCM =0V 100 150 50 200 nA Input Bias Current IIN(+) or IIN(−) with Output in Linear Range, VCM =0V (Note 5) 300 400 200 500 nA Input Common Mode Voltage Range V+ =30V (Note 6) V+−2.0 V Saturation Voltage VIN(−)=1V, VIN(+)=0, ISINK≤4 mA 700 700 700 mV Output Leakage Current VIN(−)=0, VIN(+) =1V, VO =30V 1.0 1.0 1.0 µA Differential Input Voltage Keep All VIN’s≥0V (or V−, if Used), (Note 8) 36 36 36 V V+−2.0 0 0 V+−2.0 0 400 Note 1: For operating at high temperatures, the LM393 and LM2903 must be derated based on a 125˚C maximum junction temperature and a thermal resistance of 170˚C/W which applies for the device soldered in a printed circuit board, operating in a still air ambient. The LM193/LM193A/LM293 must be derated based on a 150˚C maximum junction temperature. The low bias dissipation and the “ON-OFF” characteristic of the outputs keeps the chip dissipation very small (PD≤100 mW), provided the output transistors are allowed to saturate. Note 2: Short circuits from the output to V+ can cause excessive heating and eventual destruction. When considering short circuits to ground, the maximum output current is approximately 20 mA independent of the magnitude of V+. Note 3: This input current will only exist when the voltage at any of the input leads is driven negative. It is due to the collector-base junction of the input PNP transistors becoming forward biased and thereby acting as input diode clamps. In addition to this diode action, there is also lateral NPN parasitic transistor action www.national.com 4 (Continued) on the IC chip. This transistor action can cause the output voltages of the comparators to go to the V+ voltage level (or to ground for a large overdrive) for the time duration that an input is driven negative. This is not destructive and normal output states will re-establish when the input voltage, which was negative, again returns to a value greater than −0.3V. Note 4: These specifications are limited to −55˚C≤TA≤+125˚C, for the LM193/LM193A. With the LM293 all temperature specifications are limited to −25˚C≤TA≤+85˚C and the LM393 temperature specifications are limited to 0˚C≤TA≤+70˚C. The LM2903 is limited to −40˚C≤TA≤+85˚C. Note 5: The direction of the input current is out of the IC due to the PNP input stage. This current is essentially constant, independent of the state of the output so no loading change exists on the reference or input lines. Note 6: The input common-mode voltage or either input signal voltage should not be allowed to go negative by more than 0.3V. The upper end of the common-mode voltage range is V+−1.5V at 25˚C, but either or both inputs can go to 36V without damage, independent of the magnitude of V+. Note 7: The response time specified is for a 100 mV input step with 5 mV overdrive. For larger overdrive signals 300 ns can be obtained, see typical performance characteristics section. Note 8: Positive excursions of input voltage may exceed the power supply level. As long as the other voltage remains within the common-mode range, the comparator will provide a proper output state. The low input voltage state must not be less than −0.3V (or 0.3V below the magnitude of the negative power supply, if used). Note 9: At output switch point, VO.1.4V, RS =0Ω with V+ from 5V to 30V; and over the full input common-mode range (0V to V+−1.5V), at 25˚C. Note 10: Refer to RETS193AX for LM193AH military specifications and to RETS193X for LM193H military specifications. Ordering Information Package Temperature Range Part Number NSC Drawing LM193H* LM193H/883 LM193H-MLS LM193AH-MLS −55˚C to 125˚C LM193AH-QMLV** 8-Pin Metal Can H08C LM193AH LM193AH/883 −25˚C to 85˚C LM293H 0˚C to 70˚C LM393H LM193J/883* 8-Pin Ceramic DIP LM193AJ/883 −55˚C to 125˚C LM193AJ-QMLV** J08A LM193AJ-MLS 8-Pin Molded DIP 0˚C to 70˚C LM393N −40˚C to 85˚C LM2903N LM393M 0˚C to 70˚C LM393MX 8-Pin SOIC LM2903M −40˚C to 85˚C 8-Bump (12 mils) micro SMD N08E M08A LM2903MX LM393TL 0˚C to 70˚C LM393TLX LM2903ITL −40˚C to 85˚C TLA08AAA LM2903ITLX Note: * Also available per LM38510/11202 Note: ** See STD Mil DWG 5962-94526 5 www.national.com LM193/LM293/LM393/LM2903 Electrical Characteristics LM193/LM293/LM393/LM2903 Typical Performance Characteristics LM193/LM293/LM393, LM193A Supply Current Input Current 00570925 00570926 Response Time for Various Input Overdrives — Negative Transition Output Saturation Voltage 00570928 00570927 Response Time for Various Input Overdrives — Positive Transition 00570929 www.national.com 6 LM193/LM293/LM393/LM2903 Typical Performance Characteristics LM2903 Supply Current Input Current 00570931 00570930 Response Time for Various Input Overdrives — Negative Transition Output Saturation Voltage 00570933 00570932 Response Time for Various Input Overdrives — Positive Transition 00570934 7 www.national.com LM193/LM293/LM393/LM2903 Application Hints The differential input voltage may be larger than V+ without damaging the device (Note 8). Protection should be provided to prevent the input voltages from going negative more than −0.3 VDC (at 25˚C). An input clamp diode can be used as shown in the applications section. The LM193 series are high gain, wide bandwidth devices which, like most comparators, can easily oscillate if the output lead is inadvertently allowed to capacitively couple to the inputs via stray capacitance. This shows up only during the output voltage transition intervals as the comparator change states. Power supply bypassing is not required to solve this problem. Standard PC board layout is helpful as it reduces stray input-output coupling. Reducing the input resistors to < 10 kΩ reduces the feedback signal levels and finally, adding even a small amount (1.0 to 10 mV) of positive feedback (hysteresis) causes such a rapid transition that oscillations due to stray feedback are not possible. Simply socketing the IC and attaching resistors to the pins will cause input-output oscillations during the small transition intervals unless hysteresis is used. If the input signal is a pulse waveform, with relatively fast rise and fall times, hysteresis is not required. All input pins of any unused comparators should be tied to the negative supply. The output of the LM193 series is the uncommitted collector of a grounded-emitter NPN output transistor. Many collectors can be tied together to provide an output OR’ing function. An output pull-up resistor can be connected to any available power supply voltage within the permitted supply voltage range and there is no restriction on this voltage due to the magnitude of the voltage which is applied to the V+ terminal of the LM193 package. The output can also be used as a simple SPST switch to ground (when a pull-up resistor is not used). The amount of current which the output device can sink is limited by the drive available (which is independent of V+) and the β of this device. When the maximum current limit is reached (approximately 16mA), the output transistor will come out of saturation and the output voltage will rise very rapidly. The output saturation voltage is limited by the approximately 60Ω rSAT of the output transistor. The low offset voltage of the output transistor (1.0mV) allows the output to clamp essentially to ground level for small load currents. The bias network of the LM193 series establishes a drain current which is independent of the magnitude of the power supply voltage over the range of from 2.0 VDC to 30 VDC. It is usually unnecessary to use a bypass capacitor across the power supply line. Typical Applications (V+ =5.0 VDC) Basic Comparator Driving CMOS Driving TTL 00570935 00570936 Squarewave Oscillator Pulse Generator 00570937 Crystal Controlled Oscillator 00570938 00570940 00570939 * For large ratios of R1/R2, D1 can be omitted. www.national.com 8 LM193/LM293/LM393/LM2903 Typical Applications (V+ =5.0 VDC) (Continued) Two-Decade High Frequency VCO 00570941 V* = +30 VDC +250 mVDC ≤ VC ≤ +50 VDC 700Hz ≤ fo ≤ 100kHz Basic Comparator Non-Inverting Comparator with Hysteresis 00570906 00570909 Inverting Comparator with Hysteresis Output Strobing 00570910 00570911 9 www.national.com LM193/LM293/LM393/LM2903 Typical Applications (V+ =5.0 VDC) (Continued) AND Gate OR Gate 00570913 00570912 Large Fan-in AND Gate Limit Comparator 00570915 00570914 Comparing Input Voltages of Opposite Polarity ORing the Outputs 00570916 00570917 www.national.com 10 LM193/LM293/LM393/LM2903 Typical Applications (V+ =5.0 VDC) (Continued) Zero Crossing Detector (Single Power Supply) One-Shot Multivibrator 00570921 00570922 Bi-Stable Multivibrator One-Shot Multivibrator with Input Lock Out 00570924 00570923 Zero Crossing Detector Comparator With a Negative Reference 00570944 00570943 11 www.national.com LM193/LM293/LM393/LM2903 Typical Applications (V+ =5.0 VDC) (Continued) Time Delay Generator 00570907 Split-Supply Applications (V+ =+15 VDC and V− =−15 VDC) MOS Clock Driver 00570942 www.national.com 12 LM193/LM293/LM393/LM2903 Physical Dimensions inches (millimeters) unless otherwise noted Metal Can Package (H) NS Package Number H08C Ceramic Dual-In-Line Package NS Package Number J08A 13 www.national.com LM193/LM293/LM393/LM2903 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) SOIC Package NS Package Number M08A Molded Dual-In-Line Package (N) NS Package N08E www.national.com 14 inches (millimeters) unless otherwise noted (Continued) NOTE: UNLESS OTHERWISE SPECIFIED 1. EPOXY COATING 2. 63Sn/37Pb EUTECTIC BUMP 3. RECOMMEND NON-SOLDER MASK DEFINED LANDING PAD. 4. PIN A1 IS ESTABLISHED BY LOWER LEFT CORNER WITH RESPECT TO TEXT ORIENTATION REMAINING PINS ARE NUMBERED COUNTERCLOCKWISE. 5. XXX IN DRAWING NUMBER REPRESENTS PACKAGE SIZE VARIATION WHERE X1 IS PACKAGE WIDTH, X2 IS PACKAGE LENGTH AND X3 IS PACKAGE HEIGHT. 6. REFERENCE JEDEC REGISTRATION MO-211, VARIATION BC. 8-Bump (12 mil) micro SMD Package NS Package TLA08AAA X1 = 1.514mm X2 = 1.514mm X3 = 0.600mm LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Email: [email protected] www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: [email protected] Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: [email protected] National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. LM193/LM293/LM393/LM2903 Low Power Low Offset Voltage Dual Comparators Physical Dimensions IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated