FWL005G - FWL10G FAST RECOVERY GLASS PASSIVATED BRIDGE RECTIFIERS PRV : 50 - 1000 Volts Io : 1.0 Ampere WOB 0.39 (10.0) 0.31 (7.87) FEATURES : 0.22 (5.59) 0.18 (4.57) Glass passivated chip High case dielectric strength High surge current capability High reliability Low reverse current Low forward voltage drop Ideal for printed circuit board Fast switching for high efficiency Pb / RoHS Free + - AC 1.00 (25.4) MIN. 1.10 (27.9) MIN. * * * * * * * * * 0.034 (0.86) 0.028 (0.71) MECHANICAL DATA : AC * Case : Reliable low cost construction utilizing molded plastic technique * Epoxy : UL94V-O rate flame retardant * Terminals : Plated leads solderable per MIL-STD-202, Method 208 guaranteed * Polarity : Polarity symbols marked on case * Mounting position : Any * Weight : 1.29 grams + AC 0.22 (5.59) 0.18 (4.57) 0.22 (5.59) 0.18 (4.57) Dimension in inches and (millimeter) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Rating at 25 °C ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20%. RATING Maximum Recurrent Peak Reverse Voltage Maximum RMS Voltage Maximum DC Blocking Voltage Maximum Average Forward Current 0.375" (9.5 mm) lead length Tc = 50°C Peak Forward Surge Current Single half sine wave Superimposed on rated load (JEDEC Method) Rating for fusing ( t < 8.3 ms. ) Maximum Forward Voltage per Diode at IF = 1.0 A Maximum DC Reverse Current Ta = 25 °C at Rated DC Blocking Voltage Ta = 100 °C Maximum Reverse Recovery Time (Note 1) Typical Junction Capacitance per Diode (Note 2) Typical Thermal Resistance (Note 3) Operating Junction Temperature Range Storage Temperature Range Notes : SYMBOL VRRM VRMS VDC FWL 005G 50 35 50 FWL 01G 100 70 100 FWL 02G 200 140 200 FWL 04G 400 280 400 FWL 06G 600 420 600 FWL 08G 800 560 800 FWL 10G 1000 700 1000 UNIT V V V IF(AV) 1.0 A IFSM 30 A 2 10 1.3 10 1.0 AS V µA mA ns pf °C/W °C °C It VF IR IR(H) Trr CJ RθJA TJ TSTG 150 250 24 36 - 50 to + 150 - 50 to + 150 2 500 1 ) Measured with IF = 0.5 Amp., IR = 1 Amp., Irr = 0.25 Amp. 2 ) Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts. 3 ) Thermal resistance from Junction to Ambient at 0.375" (9.5 mm) lead length P.C. Board mounting. Page 1 of 2 Rev. 02 : March 25, 2005 RATING AND CHARACTERISTIC CURVES ( FWL005G - FWL10G ) FIG.1 - REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 Ω 10 Ω Trr + 0.5 D.U.T. + PULSE GENERATOR ( NOTE 2 ) 50 Vdc (approx) 1Ω 0 - 0.25 OSCILLOSCOPE ( NOTE 1 ) - 1.0 A SET TIME BASE FOR 50/100 ns/cm NOTES : 1. Rise Time = 7 ns max., Input Impedance = 1 megaohm , 22 pF. 2. Rise time = 10 ns max., Source Impedance = 50 ohms. 1 3. All Resistors = Non-inductive Types. FIG.2 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT FIG.3 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 30 PC Board 0.375(9.5mm) 0.8 Copper Pads 0.22" x 0.22" (5.5 x5.5m m ) 0.6 0.4 0.2 60 Hz, Resistive or Inductive load. 0 0 25 50 75 100 125 150 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD OUTPUT CURRENT, AMPERES 1.0 24 T J = 55 °C 18 12 SINGLE HALF SINE WAVE (JEDEC METHOD) 6 0 175 1 CASE TEMPERATURE, ( °C) 20 10 1 TJ = 25 °C Pulse W idth = 300 µs 1 % Duty Cycle 0.01 0.4 0.8 1.2 1.6 2.0 2.4 2.8 FORWARD VOLTAGE, VOLTS Page 2 of 2 4 6 10 20 40 60 100 FIG.5 - TYPICAL REVERSE CHARACTERISTICS REVERSE CURRENT, MICROAMPERES FORWARD CURRENT, AMPERES FIG.4 - TYPICAL FORWARD CHARACTERISTICS 0.1 2 NUMBER OF CYCLES AT 60Hz 3.2 10 T J = 100 °C 1.0 T J = 25 °C 0.1 0.01 0 20 40 60 80 100 120 140 PERCENT OF RATED REVERSE VOLTAGE, (%) Rev. 02 : March 25, 2005