Sharp LQ104V1DG51 Tft lcd module Datasheet

LQ104V1DG51
TFT-LCD Module
(Model Number: LQ104V1DG51)
Specifications
Spec No.: LD-13708A
Dated: June ６, 2002
PREPARED BY :
DATE
SPEC No. LD-13708A
FILE No.
ISSUE : Jul.18 2001
APPROVED BY :
DATE
PAGE :
TFT Liquid Crystal Display Group
SHARP CORPORATION
18 pages
APPLICABLE GROUP
TFT Liquid Crystal Display
Group
SPECIFICATION
DEVICE SPECIFICATION FOR
TFT-LCD Module
MODEL No.
LQ104V1DG51
□ CUSTOMER'S APPROVAL
DATE
PRESENTED
BY
BY
K.Shiono
General
Manager
Development Engineering Dept.Ⅱ
TFT Division.Ⅱ
TFT LIQUID CRYSTAL DISPLAY GROUP
SHARP CORPORATION
LD13708-1
1. Application
This technical literature applies to color TFT-LCD module, LQ104V1DG51
These technical literature sheets are the proprietary product of SHARP CORPORATION(”SHARP) and
include materials protected under copyright of SHARP. Do not reproduce or cause any third party to
reproduce them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part,
without the express written permission of SHARP .
The device listed in these technical literature sheets was designed and manufactured for use in general
electronic equipment.
In case of using the device for applications such as control and safety equipment for transportation(aircraft,
trains, automobiles, etc. ), rescue and security equipment and various safety related equipment which
require higher reliability and safety, take into consideration that appropriate measures such as fail-safe
functions and redundant system design should be taken .
Do not use the device for equipment that requires an extreme level of reliability, such as aerospace
applications, telecommunication equipment(trunk lines), nuclear power control equipment and medical or
other equipment for life support .
SHARP assumes no responsibility for any damage resulting from the use of the device which does not
comply with the instructions and the precautions specified in these technical literature sheets .
Contact and consult with a SHARP sales representative for any questions about this device .
2. Overview
This module is a color active matrix LCD module incorporating amorphous silicon TFT
(Thin Film Transistor). It is composed of a color TFT-LCD panel, driver ICs, control
circuit and power supply circuit and a backlight unit. Graphics and texts can be
displayed on a 640×3×480 dots panel with 262,144 colors by supplying 18 bit data signal
(6bit/color), four timing signals,+3.3V/ +5V DC supply voltage for TFT-LCD panel driving and
supply voltage for backlight.
The TFT-LCD panel used for this module is a low-reflection and higher-color-saturation
type. Therefore, this module is also suitable for the multimedia use.
Optimum viewing direction is 6 o'clock.
Backlight-driving DC/AC inverter is not built in this module.
LD13708-2
3. Mechanical Specifications
Parameter
Specifications
Diagonal
Unit
Display size
26 (10.4")
cm
Active area
211.2(H)×158.4(V)
mm
Pixel format
640(H)×480(V)
pixel
(1 pixel＝R＋G＋B dots)
Pixel pitch
0.330(H)×0.330(V)
Pixel configuration
R,G,B vertical stripe
Display mode
Normally white
Unit outline dimensions *1
246.5(W)×179.4(H)×14.2(D)
Mass
600±20
Surface treatment
Anti-glare and hard-coating
Haze value = 26%±5%
*1.Note: excluding backlight cables.
Outline dimensions is shown in Fig.1-1/Fig.1-2
mm
mm
g
LD13708-3
4. Input Terminals
4-1. TFT-LCD panel driving
CN1
Used connector:DF9MA-31P-1V (Hirose Electric Co., Ltd.)
1
31 Corresponding connector: DF9-31S-1V (
〃 )
2
30
DF9A-31S-1V( 〃 )
CN1 pin arrangement from module surface
DF9B-31S-1V( 〃 )
(Transparent view)
DF9M-31S-1V( 〃 )
Pin No. Symbol
Function
Remark
1
GND
2
CK
Clock signal for sampling each data signal
3
Hsync
Horizontal synchronous signal
【Note1】
4
Vsync
Vertical synchronous signal
【Note1】
5
GND
6
R0
ＲＥＤ data signal(LSB）
7
R1
ＲＥＤ data signal
8
R2
ＲＥＤ data signal
9
R3
ＲＥＤ data signal
10
R4
ＲＥＤ data signal
11
R5
ＲＥＤ data signal(MSB)
12
GND
13
G0
ＧＲＥＥＮ data signal(LSB）
14
G1
ＧＲＥＥＮ data signal
15
G2
ＧＲＥＥＮ data signal
16
G3
ＧＲＥＥＮ data signal
17
G4
ＧＲＥＥＮ data signal
18
G5
ＧＲＥＥＮ data signal(MSB)
19
GND
20
B0
ＢＬＵＥ data signal(LSB）
21
B1
ＢＬＵＥ data signal
22
B2
ＢＬＵＥ data signal
23
B3
ＢＬＵＥ data signal
24
B4
ＢＬＵＥ data signal
25
B5
ＢＬＵＥ data signal(MSB)
26
GND
27
ENAB
Signal to settle the horizontal display position
【Note2】
28
Vcc
＋5.0V power supply
29
Vcc
＋5.0V power supply
30
R/L
Horizontal display mode select signal
【Note3】
31
U/D
Vertical display mode select signal
【Note4】
※The shielding case is not connected with GND.
【Note1】480 line, 400 line or 350 line mode
Mode
480 lines
400 lines
350 lines
is selected by the polarity combination
Hsync
negative
negative
Positive
of the both synchronous signals.
Vsync
negative
positive
Negative
【Note2】The horizontal display start timing is settled
in
accordance with a rising timing of ENAB signal. In case ENAB is fixed "Low", the horizontal start timing is
determined as described in
7-2. Don't keep ENAB “High" during operation.
LD13708-4
【Note3】Ｒ／Ｌ＝Ｈｉｇｈ、Ｕ／Ｄ＝Ｌｏｗ
Ｒ／Ｌ＝Ｌｏｗ、Ｕ／Ｄ＝Ｌｏｗ
【Note4】Ｒ／Ｌ＝Ｈｉｇｈ、Ｕ／Ｄ＝Ｈｉｇｈ
Ｒ／Ｌ＝Ｌｏｗ、Ｕ／Ｄ＝Ｈｉｇｈ
4-2. Backlight driving
Used connector : BHR-03VS-1(JST)
CN2、CN3
Corresponding connector :SM02(8.0)B-BHS(JST)
Pin no.
Symbol
1
ＶHIGH
Function
Cable color
Power supply for lamp
Pink
(High voltage side)
2
NC
This is electrically opened.
3
ＶLOW
Power supply for lamp
White
(Low voltage side)
5. Absolute Maximum Ratings
Parameter
Input voltage
Symbol Condition
VI
Ratings
Unit
Ta=25℃ －0.3 ～ Vcc＋0.3 Ｖ
+5V supply voltage
Vcc
Ta=25℃
0 ～ ＋ 6
Ｖ
Storage temperature
Tstg
－
－30 ～ ＋70
℃
Operating temperature (Ambient)
Topa
－
－10 ～ ＋65
℃
【Note1】CK,R0～R5,G0～G5,B0～B5,Hsync,Vsync,ENAB, R/L, U/L
【Note2】Humidity：95%RH Max. at Ta≦40℃.
Maximum wet-bulb temperature at 39℃ or less at Ta>40℃.
No condensation.
Remark
【Note1】
【Note2】
LD13708-5
6. Electrical Characteristics
6-1.TFT-LCDpaneldriving
Ta＝25℃
Parameter
Supply voltage
Power
Supply Current dissipation
Permissive input ripple voltage
Input voltage (Low)
Input voltage (High)
Symbol
Vcc
Min.
Typ.
Max.
+3.0 +3.3 +5.0 +5.5
Unit
V
Remark
【Note1】
Icc
－
350
400
ｍＡ
Vcc=3.3V
【Note2】
Icc
－
250
300
ｍＡ
Vcc=5.0V
【Note2】
VRF
VIL
VIH
IOL1
－
－
－
－
－
－
0.7Vcc
－
100 mVp-p
0.3Vcc Ｖ
－
Ｖ
μＡ
1.0
－
－
μＡ
60.0
IOH1
－
－
1.0
IOH2
－
－
60.0
【Note3】
VI=0V
【Note4】
VI=0V
Input current (low)
IOL2
Vcc=+5V
【Note5】
VI=Vcc
μＡ
【Note6】
VI=Vcc
μＡ
Input current (High)
【Note7】
【 NOTE 1】
Vcc-turn-on conditions
VCC
VCC
4.5V
Ｔ１≦１５ｍｓ
０＜Ｔ２≦１０ｍｓ
０＜Ｔ３≦１ｓ
１ｓ＜Ｔ４
2.8V
0.3V
T３
Vcc-dip conditions
480 line mode/Vcc=+3.3V/＋5.0V
【Note3】 CK,R0~R5,G0~G5,B0~B5,Hsync,Vsync,ENAB,
R/L,U/D
【Note4】 CK,R0~R5,G0~G5,B0~B5,Hsync,Vsync,ENAB
【Note5】 R/L
【Note6】 CK,R0~R5,G0~G5,B0~B5,Hsnc,Vsync
【Note7】 ENAB,U/D
T1
T４
VCC
T２
3.0V
１） ２．７Ｖ≦Ｖｃｃ＜３．０Ｖ
ｔｄ≦１０ｍｓ
２） Ｖｃｃ＜２．７Ｖ
Vcc-dip condition should also follow
The Vcc-turn-on conditions
【Note2】 Typical current situation : 16-gray-bar pattern.
0.3V
2.7V
Ｔｄ
RGB
RGB
RGB
GS0
GS3
GS7
RGB
RGB
GS59
GS63
....
LD13708-6
6-2. Backlight driving
The backlight system is an edge-lighting type with single CCFT (Cold Cathode
Fluorescent Tube). The characteristics of single lamp are shown in the following table.
Ta=25℃
Parameter
Symbol
Min.
Typ.
Max.
Unit
Remark
Lamp current
IL
3.5
6.0
7.0
mArms 【Note1】
2.8
Lamp power consumption
PL
－
－
Ｗ 【Note2】
Lamp frequency
FL
40
60
70
KHz 【Note3】
Kick-off voltage
Vs
1000
Vrms Ta=25℃
－
－
1300
Vrms Ta =0℃【Note4】
－
－
Lamp life time
LL
50000
hour 【Note5】IL=6.0mA
－
－
LL
30000
hour 【Note5】IL=7.0mA
－
－
【Note1】 Lamp current is measured with current meter for high frequency as shown below.
１
Module
3
１
3
Ａ
～
Inverter
Ａ
～
* 3pin is V
LOW
【Note2】 At the condition of YL =350cd/m2
【Note3】 Lamp frequency may produce interference with horizontal synchronous frequency,and
this may cause beat on the display. Therefore lamp frequency shall be detached as
much as possible from the horizontal synchronous frequency and from the harmonics
of horizontal synchronous to avoid interference.
【Note4】The open output voltage of the inverter shall be maintained for more than 1sec; otherwise
the lamp may not be turned on.
【Note5】Since lamp is consumables, the life time written above is referencial value and it is not
guaranteed in this specification sheet by SHARP.
Lamp life time is defined that it applied either ① or ② under this condition
(Continuous turning on at Ta=25℃, IL=6/7mArms)
① Brightness becomes 50% of the original value under standard condition.
② Kick-off voltage at Ta=0℃ exceeds maximum value,(TBD) Vrms.
In case of operating under lower temp environment, the lamp exhaustion is accelerated and the
brightness becomes lower.
(Continuous operating under for around 1 month under lower temp condition may reduce the
brightness to half of the original brightness.)
In case of such usage under lower temp environment, periodical lamp exchange is recommended.
【Note6】The performance of the backlight, for example life time or brightness, is much influenced
by the characteristics of the DC-AC inverter for the lamp. When you design or order the
inverter, please make sure that a poor lighting caused by the mismatch of the backlight and
the inverter (miss-lighting,flicker, etc.) never occur. when you confirm it, the module should
be operated in the same condition as it is installed in your instrument.
【Note7】 It is required to have the inverter designed so that to allow the impedance deviation
of the two CCFT lamps and the capacity deviation of barast capacitor.
LD13708-7
7. Timing Characteristics of input signals
Timing diagrams of input signal are shown in Fig.2 - ①～③
.
7-1. Timing characteristics
Parameter
Clock
Data
Horizontal
Symbol Mode
Typ.
Max.
Unit
Frequency
1/Tc
all
－
25.18
28.33
MHz
High time
Tch
〃
5
－
－
ns
Low time
Tcl
〃
10
－
－
ns
Setup time
Tds
〃
5
－
－
ns
Hold time
Tdh
〃
10
－
－
ns
Cycle
TH
〃
30.00
31.78
－
μs
〃
770
800
900
clock
sync. signal
Vertical
Min.
Pulse width
THp
〃
2
96
200
clock
Cycle
TV
480
515
525
560
line
400
445
449
480
line
350
447
449
510
line
sync. signal
Pulsewidth
TVp
all
1
－
34
line
Horizontal display period
THd
〃
640
640
640
clock
Hsync-Clock
THc
〃
10
－
Tc-10
ns
TVh
〃
0
－
Remark
phase difference
Hsync-Vsync
TH-THp clock
phase difference
Note) In case of lower frequency, the deterioration of display quality, flicker etc.,may be occurred.
7-2. Horizontal display position
The horizontal display position is determined by ENAB signal and the input data corresponding
to the rising edge of ENAB signal is displayed at the left end of the active area.
Parameter
symbol
Min.
Typ.
Max.
Unit
Enable signal Setup time
Tes
5
－
Tc-10
ns
Pulse width
Tep
2
640
640
clock
THe
44
－
TH-664
clock
Hsync-Enable signal
Remark
phase difference
Note) When ENAB is fixed "Low", the display starts from the data of C104(clock) as shown
in
Fig.2-①～③. Be careful that the module does not work when ENAB is fixed "High".
When the phase difference is below 104 clock, keep the “High level of ENAB is signal longer
Than 104-The. If it will not be keeped, the display starts from the data of C104(clock).
LD13708-8
7-3. Vertical display position
The vertical display position is automatically centered in the active area at each mode
of VGA ,480-,400-,and 350-line mode . Each mode is selected depending on the polarity of
the synchronous signals described in 4-1(Note1).
In each mode ,the data of TVn is displayed at the top line of the active area. And the
display position will be centered on the screen like the following figure when the period of
vertical synchronous signal,TV,is typical value.
In 400-,and 350-line mode,the data in the vertical data invalid period is also displayed,
So ,inputting all data "0" is recommended during vertical data invalid period.
ENAB signal has no relation to the vertical display position.
Mode V-data start(TVs)
V-data
V-display start(TVn)
V-display period Unit
Remark
period(TVd)
480
34
480
34
480
line
400
34
400
443-TV
480
line
350
61
350
445-TV
480
line
data invalid period
４０lines
data period
data period
４００lines
data invalid period
６５lines
data invalid period
３５０lines
６５lines
data invalid period
４０lines
400 lines mode (TV=449)
350 lines mode (TV=449)
7-4. Input Data Signals and Display Position on the screen
Display position of input data (480 lines mode)
（Ｈ，Ｖ）
D1,DH1
D2,DH1
D1,DH2
D2,DH2
D3,DH1
ＵＰ
D640,DH1
D1,DH3
R
D1,DH480
G
B
D640,DH480
TH
THp
THc
* Only when enable terminal is fixed "Low"
c
c
V
3
.
0
C1*
C2*
C104*
Number of clock
Tds Tdh
Number of H-data
c
c
V
7
.
0
Horizontal invalid da ta period
D1
D2
THe
D3
D639
c
c
V
3
.
0
Data signal
(R0~R5,G0~G5,
B0~B5)
Tc
Tch Tcl
c
c
V
7
.
0
c
c
V
3
.
0
c
c
V
3
.
0
c
c
V
3
.
0
c
c
V
3
.
0
Clock signal
(CK)
c
c
V
3
.
0
c
c
V
7
.
0
c
c
V
3
.
0
c
c
V
3
.
0
Horizontal
sync. signal
(Hsync)
D640
Horizontal invalid da ta period
THd
c
c
V
3
.
0
c
c
V
7
.
0
Tes
Data enable signal
(ENAB)
Tep
TV
c
c
V
7
.
0
TVp
c
c
V
3
.
0
c
c
V
3
.
0
Vertical
sync. signal
(Vsync)
TVh
c
c
V
7
.
0
2
34
TVs
Data signal
(R0~R5,G0~G5,
B0~B5)
TVd
Vertical invalid data period
DH1
DH2
DH3
DH479
DH480
Vertical invalid data period
Number of V-data line
Fig2-1
Input
signal
Fig 2-1
Input
signal waveforms(480
waveforms (480line
line mmode)
ＬＤ１３７０８－９
1
e
n
i
l
f
o
r
e
b
m
u
N
Horizontal
sync.
signal
(Hsync)
TH
THp
c
c
V
3
.
0
c
c
V
7
.
0
c
c
V
3
.
0
c
c
V
3
.
0
Horizontal
sync.
signal
(Hsync)
THc
C2*
c
c
V
3
.
0
c
c
V
3
.
0
c
c
V
3
.
0
c
c
V
3
.
0
C104*
k
c
o
l
c
f
o
r
e
b
m
u
N
C1*
Tds Tdh
Number of H-data
c
c
V
7
.
0
D1
Horizontal data invalid
period
D2
THe
D3
D639
c
c
V
3
.
0
Data signal
(R0~R5,G0~G5,
B0~B5)
c
c
V
7
.
0
* Only when enable terminal (ENAB) is fixed
Clock signal
(CK)
Tc
Tch Tcl
Horizontal data invalid
period
D640
THd
c
c
V
7
.
0
c
c
V
3
.
0
Tes
Data enable
signal
(ENAB)
Tep
TV
c
c
V
7
.
0
c
c
V
7
.
0
c
c
V
3
.
0
Vertical
sync.
signal
(Vsync)
TVp
TVh
c
c
V
7
.
0
1
2
34
Number of line
TVs
Data signal
(R0~R5,G0~G5,
B0~B5)
Vertical invalid data period
TVd
DH1
DH2
DH3
DH399
DH400
Vertical invalid data period
e
n
i
l
a
t
a
d
V
f
o
r
e
b
m
u
N
Fig2-2
Input
waveforms(400
line
Fig.2-2
Inputsignal
signal waveforms
(400
linemode)
ＬＤ１３７０８－１０
Horizontal
sync. signal
(Hsync)
TH
c
c
V
7
.
0
c
c
V
7
.
0
c
c
V
7
.
0
c
c
V
3
.
0
Horizontal
sync. signal
(Hsync)
THp
THc
* Only when enable terminal (ENAB) fixed to "Low
c
c
V
3
.
0
C2*
k
c
o
l
c
f
o
r
e
b
m
u
N
C1*
C104*
Tds Tdh
Number of H-data
c
c
V
7
.
0
Horizontal invalid data period
D1
D2
THe
D3
D639
c
c
V
3
.
0
Data signal
(R0~R5,G0~G5,
B0~B5)
c
c
V
7
.
0
c
c
V
3
.
0
c
c
V
3
.
0
c
c
V
3
.
0
Clock signal
(CK)
Tc
Tch Tcl
Horizontal invalid data
period
D640
THd
c
c
V
7
.
0
c
c
V
3
.
0
Tes
Data enable signal
(ENAB)
Tep
TV
c
c
V
7
.
0
TVp
c
c
V
3
.
0
c
c
V
3
.
0
Vertical
sync. signal
(Vsync)
TVh
c
c
V
3
.
0
Horizontal
sync. signal
(Hsync)
1
2
61
TVs
Vertical invalid data period
TVd
DH1
DH2
DH3
DH349
DH350
Vertical invalid data period
Number of V-data line
Fig.2-3 Input signal waveforms (350 line mod
Fig2-3 Input signal waveforms(350
line
mode)
ＬＤ１３７０８－１1
ＬＤ１３７０８－１1
Data signal
(R0~R5,G0~G5,
B0~B5)
Number of
li
LD13708-12
8. Input Signals, Basic Display Colors and Gray Scale of Each Color
Colors &
Gray scale
Data signal
Gray
RA0 RA1 RA2 RA3 RA4 RA5 GA0 GA1 GA2 GA3 GA4 GA5 BA0 BA1 BA2 BA3 BA4 BA5
Scale
RB0 RB1 RB2 RB3 RB4 RB5 GB0 GB1 GB2 GB3 GB4 GB5 BB0 BB1 BB2 BB3 BB4 BB5
Black
－
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Blue
－
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
Green
－
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
Cyan
－
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
Red
－
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
Magenta
－
1
1
1
1
1
1
0
0
0
0
0
0
1
1
1
1
1
1
Yellow
－
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
White
－
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Black
GS0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
×
GS1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
Darker
GS2
0
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
×
È
È
È
È
Ø
È
È
È
È
Brighter
GS61
1
0
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
Ø
GS62
0
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
Red
GS63
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
Black
GS0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
×
GS1
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
0
Darker
GS2
0
0
0
0
0
0
0
1
0
0
0
0
0
0
0
0
0
0
×
È
È
È
È
Ø
È
È
È
È
Brighter
GS61
0
0
0
0
0
0
1
0
1
1
1
1
0
0
0
0
0
0
Ø
GS62
0
0
0
0
0
0
0
1
1
1
1
1
0
0
0
0
0
0
Green
GS63
0
0
0
0
0
0
1
1
1
1
1
1
0
0
0
0
0
0
Black
GS0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
×
GS1
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
0
Darker
GS2
0
0
0
0
0
0
0
0
0
0
0
0
0
1
0
0
0
0
×
È
È
È
È
Ø
È
È
È
È
Brighter
GS61
0
0
0
0
0
0
0
0
0
0
0
0
1
0
1
1
1
1
Ø
GS62
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
Blue
GS63
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
r
o
l
o
C
c
i
s
a
B
d
e
R
f
o
e
l
a
c
S
y
a
r
G
n
e
e
r
G
f
o
e
l
a
c
S
y
a
r
G
e
u
l
B
f
o
e
l
a
c
S
y
a
r
G
0 :Low level voltage, 1 : High level voltage
Each basic color can be displayed in 64 gray scales from 6 bit data signals. According to the combination of total 18 bit
LD13708-13
data signals, the 262,144-color display can be achieved on the screen.
Ta=25℃, Vcc=+5V
9. Optical Characteristics
Parameter
Viewing
Angle
Symbol
Condition
Min
Typ
Max
Unit
Remark
Horizontal θ21,θ22 ＣＲ≧１０
60
70
－
Deg.
【Note1,4】
θ11
35
40
－
Deg.
θ12
55
70
－
Deg.
θ=０°
150
－
－
－
Best Viewing
－
300
－
－
－
20
－
ｍｓ
ｍｓ
Vertical
Range
Contrast ratio
ＣＲ
【Note2,4】
Angle
Response
Rise
τr
Time
Decay
τd
－
40
－
Chromaticity of
ｘ
－
0.313
－
White
ｙ
－
0.329
－
Luminance of white
ＹＬ
－
350
－
cd/m2
White Unifomity
δＷ
－
－
1.45
－
【Note5】
－
45
－
Deg.
【Note1】
－
35
－
Deg.
－
35
－
Deg.
Viewing
Horizontal θ21,θ22
50% of
【Note3,4】
【Note4】
the
Angle
range as a
Brightness
Definition
※The
θ=０°
Vertical
θ11
θ12
maximum
brightness
measurement shall be executed 30 minutes after lighting at rating. (typical condition:IL=6.0mArms)
The optical characteristics shall be measured in a dark room or equivalent state
with the method shown in Fig.3 below.
Photodetector (BM-5A:TOPCON)
Ｆｉｅｌｄ＝２°
４００ｍｍ
ＴＦＴ－ＬＣＤ module
ＬＣＤ panel
Center of the screen
Fig.3 Optical characteristics measurement method
LD13708-14
【Note1】Definitions of viewing angle range:
【Note2】Definition of contrast ratio:
The contrast ratio is defined as the following.
Luminance (brightness) with all pixels white
Contrast Ratio (CR) ＝
Luminance (brightness) with all pixels black
【Note3】Definition of response time:
The response time is defined as the following figure and shall be measured by
switching the input signal for "black" and "white" .
【Note4】This shall be measured at center of the screen.
【Note5】Definition of white uniformity:
White uniformity is defined as the
following with five measurements
160
320
480 pixel
(A～E).
A
D
240
C
B
δw＝
Maximum Luminance of five points (brightness)
Minimum Luminance of five points (brightness)
120
E
360
pixel
LD13708-15
10. Display Quantity
The display quality of the color TFT-LCD module shall be in compliance with the
Incoming Inspection Standard.
11．Handling Precautions
a) Be sure to turn off the power supply when inserting or disconnecting the cable.
b) Be sure to design the cabinet so that the module can be installed without any extra stress such as
warp or twist.
c) Since the front polarizer is easily damaged, pay attention not to scratch it.
d) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
e) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
f) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
Handle with care.
g) Since CMOS LSI is used in this module, take care of static electricity and injure the human earth
when handling.
h) Observe all other precautionary requirements in handling components.
i) This module has its circuitry PCBs on the rear side and should be carefully handled in order not
to be stressed.
j) The polarizer surface on the panel is treated with Anti-Glare for low reflection. In case of attaching
protective board over the LCD. Be careful about the optical interface fringe etc.
Which degrades display quality.
k) Connect GND to 4 place of mounting holes to stabilize against EMI and external noise.
l) There are high voltage portions on the backlight and very dangerous. Careless touch may lead to
electrical shock. When exchange lamps or service. Turn off the power without tail.
m) Be sure not to apply tensile stress to the lamp lead cable.
12.Packing form
Product country
JAPAN
Piling number of cartons
７（Max）
Packing quantity in one carton
20
Carton size
494(W)×326(D)×433(H)
[mm]
Total mass of one carton filled 15.6kg
with full modules
Packing form is shown
Fig.1-2
LD13708-16
13．Reliability test items
No.
Test item
Conditions
1
High temperature storage test
Ta=70℃
240h
2
Low temperature storage test
Ta=-30℃
240h
3
High temperature
Ta=40℃ ; 95%RH 240h
& high humidity operation test
(No condensation)
4
High temperature operation test
Ta=65℃
5
Low temperature operation test
Ta=-10℃
6
Vibration test
Frequency: 10～57Hz/Vibration width (one side):0.075mm
240h
240h
: 58～500Hz/Gravity:9.8m/s2
(non- operating)
Sweep time : 11 minutes
Test period : 3 hours
(1 hour for each direction of X,Y,Z)
7
Shock test
Max. gravity : 490m/s2
(non- operating)
Pulse width : 11ms, half sine wave
Direction : ±X,±Y,±Z
once for each direction.
【Result Evaluation Criteria】
Under the display quality test conditions with normal operation state, these shall be no change
which may affect practical display function.
14．Others
P
R
A
H
S
1) Lot No Label:
Model No.
LQ104V1DG51
07 XXXXXX＿
MADE IN □□□□□
Lot No.
JAPAN
2) Adjusting volume have been set optimally before shipment, so do not change any adjusted value.
If adjusted value is changed, the specification may not be satisfied.
3) Disassembling the module can cause permanent damage and should be strictly avoided.
4) Please be careful since image retention may occur when a fixed pattern is displayed for a long
time
5) Do not use LCD module in the atmosphere of corrosive gases, such as sulfide gas or chlorine gases.
Polarizer may deteriorated or cause chemical reaction that can lead to short circuits at the terminal
Points. Do not use the material, which compounds contain sulfide or chlorine articles in the vicinity of
LCD module. At high temperature, these compounds produce corrosive gases.
6) If any problem occurs in relation to the description of this specification , it shall be resolved
through discussion with spirit of cooperation.
SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.
Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited
Warranty for SHARP’s product warranty. The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied.
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND
FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or in any way responsible,
for any incidental or consequential economic or property damage.
NORTH AMERICA
EUROPE
JAPAN
SHARP Microelectronics of the Americas
5700 NW Pacific Rim Blvd.
Camas, WA 98607, U.S.A.
Phone: (1) 360-834-2500
Fax: (1) 360-834-8903
Fast Info: (1) 800-833-9437
www.sharpsma.com
SHARP Microelectronics Europe
Division of Sharp Electronics (Europe) GmbH
Sonninstrasse 3
20097 Hamburg, Germany
Phone: (49) 40-2376-2286
Fax: (49) 40-2376-2232
www.sharpsme.com
SHARP Corporation
Electronic Components & Devices
22-22 Nagaike-cho, Abeno-Ku
Osaka 545-8522, Japan
Phone: (81) 6-6621-1221
Fax: (81) 6117-725300/6117-725301
www.sharp-world.com
TAIWAN
SINGAPORE
KOREA
SHARP Electronic Components
(Taiwan) Corporation
8F-A, No. 16, Sec. 4, Nanking E. Rd.
Taipei, Taiwan, Republic of China
Phone: (886) 2-2577-7341
Fax: (886) 2-2577-7326/2-2577-7328
SHARP Electronics (Singapore) PTE., Ltd.
438A, Alexandra Road, #05-01/02
Alexandra Technopark,
Singapore 119967
Phone: (65) 271-3566
Fax: (65) 271-3855
SHARP Electronic Components
(Korea) Corporation
RM 501 Geosung B/D, 541
Dohwa-dong, Mapo-ku
Seoul 121-701, Korea
Phone: (82) 2-711-5813 ~ 8
Fax: (82) 2-711-5819
CHINA
HONG KONG
SHARP Microelectronics of China
(Shanghai) Co., Ltd.
28 Xin Jin Qiao Road King Tower 16F
Pudong Shanghai, 201206 P.R. China
Phone: (86) 21-5854-7710/21-5834-6056
Fax: (86) 21-5854-4340/21-5834-6057
Head Office:
No. 360, Bashen Road,
Xin Development Bldg. 22
Waigaoqiao Free Trade Zone Shanghai
200131 P.R. China
Email: [email protected]
SHARP-ROXY (Hong Kong) Ltd.
3rd Business Division,
17/F, Admiralty Centre, Tower 1
18 Harcourt Road, Hong Kong
Phone: (852) 28229311
Fax: (852) 28660779
www.sharp.com.hk
Shenzhen Representative Office:
Room 13B1, Tower C,
Electronics Science & Technology Building
Shen Nan Zhong Road
Shenzhen, P.R. China
Phone: (86) 755-3273731
Fax: (86) 755-3273735