Snap-In Capacitors B43304 Miniaturized – 85 °C B43304 General-purpose grade capacitors Applications ■ Switch-mode power supplies in industrial and entertainment electronics Features ■ Extremely miniaturized ■ High ripple current capability ■ Many different case sizes available for each capacitance value Construction ■ ■ ■ ■ ■ ■ Charge-discharge proof, polar Aluminum case, fully insulated Snap-in solder pins to hold component in place on PC-board Minus pole marking on case surface Minus pole not insulated from case Overload protection (safety vent) Terminals ■ Standard version with 2 terminals 2 lengths available: 6,3 and 4,5 mm ■ 3 terminals: length 4,5 mm (terminal arrangement ensures correct insertion) 223 10/02 B43304 Miniaturized – 85 °C Specifications and characteristics in brief Rated voltage UR 200 … 450 VDC Surge voltage US 1,15 · UR (for UR ≤ 250 VDC) 1,10 · UR (for UR ≥ 400 VDC) Rated capacitance CR 82 … 2 200 µF Capacitance tolerance ± 20 % M UR ≤ 250 V: tan δ ≤ 0,15 UR ≥ 400 V: tan δ ≤ 0,20 Dissipation factor tan δ (20 °C, 120 Hz) Leakage current IL (5 min, 20 °C) C R U R 0,7 I L ≤ 0,3 µA ⋅ æè ------- ⋅ ------- öø + 4 µA µF V Self-inductance ESL Approx. 20 nH Useful life 85 °C; UR; I~max 40 °C; UR; 1,15 · I~R Requirements: > 2 000 h > 100 000 h ∆C/C tan δ IL ≤ ± 30 % of initial value ≤ 3 times initial specified limit ≤ initial specified limit Failure percentage: ≤ 1 % Failure rate: ≤ 100 fit (≤ 100 · 10 –9/h) (for definiton “fit”, refer to chapter “Quality”, page 62) Load life test 85 °C; UR; I~R Post test requirements: 2 000 h Voltage endurance test ∆C/C tan δ IL ≤ ± 20 % of initial value ≤ 2 times initial specified limit ≤ initial specified limit Post test requirements: ∆C/C tan δ IL ≤ ± 10 % of initial value ≤ 1,3 times initial specified limit ≤ initial specified limit 85°C; UR 2 000 h Vibration resistance To IEC 60068-2-6, test Fc: displacement amplitude 0,35 mm, frequency range 10 … 55 Hz, acceleration max. 5 g, duration 3 × 2 h To IEC 60068-1: UR ≤ 250 VDC: 40/085/56 (– 40°C/+ 85°C/56 days damp heat test) UR ≥ 400 VDC: 25/085/56 (– 25°C/+ 85°C/56 days damp heat test) Similar to CECC 30301-806 IEC 60384-4 IEC climatic category Detail specification Sectional specification 224 10/02 B43304 Miniaturized – 85 °C Dimensional drawings Minus pole marking Minus pole marking Mounting holes Mounting holes KAL0140-J KAL0324-F Snap-in terminals, standard (length 6,3 ± 1 mm). Also available in a shorter version with a length of 4,5 –1 mm. For packing mode and ordering example see next page. Snap-in capacitors are also available with 3 terminals (length 4,5 –1 mm). For packing mode and ordering example see next page. Dimensions (mm) d+1 l±2 Approx. Packing units weight (g) (pieces) Dimensions (mm) d+1 l±2 Approx. Packing units weight (g) (pieces) 22 22 22 22 22 22 25 30 35 40 45 50 9 12 15 18 20 24 160 160 160 160 160 160 30 30 30 30 30 30 25 30 35 40 45 50 17 23 29 36 41 46 80 80 80 80 80 80 25 25 25 25 25 25 25 30 35 40 45 50 13 17 19 22 25 29 130 130 130 130 130 130 35 35 35 35 35 35 25 30 35 40 45 50 22 29 36 41 56 70 60 60 60 60 60 60 225 10/02 B43304 Miniaturized – 85 °C Packing of snap-in capacitors For ecological reasons the packing is pure cardboard. Components can be withdrawn (in full or in part) in the correct position for insertion. Ordering codes Snap-in terminals Version Identification in 3rd block of ordering code Standard terminals (6,3 ± 1) mm M000 Short terminals (4,5 −1) mm M007 3 terminals (4,5 −1) mm M002 Ordering example: B43304A9107M007 B43304A9107M002 } } snap-in capacitor with short terminals snap-in capacitor with 3 terminals 226 10/02 B43304 Miniaturized – 85 °C Overview of available types UR (VDC) 200 CR (µF) Case dimensions d × l (mm) 400 450 82 22 × 25 100 22 × 25 22 × 30 25 × 25 120 22 × 30 25 × 25 22 × 35 25 × 30 150 22 × 35 25 × 30 22 × 40 25 × 30 30 × 25 180 22 × 40 25 × 30 30 × 25 22 × 45 25 × 35 30 × 30 220 22 × 25 22 × 45 25 × 35 30 × 30 22 × 50 25 × 40 30 × 30 35 × 25 22 × 30 22 × 50 25 × 40 30 × 30 35 × 25 25 × 45 30 × 35 35 × 30 270 250 330 22 × 25 22 × 30 25 × 25 25 × 45 30 × 35 35 × 30 30 × 40 35 × 35 390 22 × 30 25 × 25 22 × 35 25 × 30 25 × 50 30 × 40 35 × 30 30 × 45 35 × 35 470 22 × 35 25 × 30 22 × 40 25 × 35 30 × 25 30 × 45 35 × 35 30 × 50 35 × 40 560 22 × 35 25 × 30 22 × 45 25 × 35 30 × 30 30 × 50 35 × 40 35 × 45 680 22 × 40 25 × 35 30 × 25 22 × 50 25 × 40 30 × 30 35 × 25 35 × 45 820 22 × 45 25 × 40 30 × 30 35 × 25 25 × 45 30 × 35 35 × 30 227 10/02 B43304 Miniaturized – 85 °C Overview of available types UR (VDC) 200 250 CR (µF) Case dimensions d × l (mm) 1 000 25 × 45 30 × 35 35 × 30 30 × 40 35 × 35 1 200 25 × 50 30 × 40 35 × 30 30 × 45 35 × 35 1 500 30 × 45 35 × 35 35 × 45 1 800 30 × 50 35 × 40 35 × 50 2 200 35 × 45 400 450 The capacitance and voltage ratings listed above are available in different cases upon request. Other voltage and capacitance ratings are also available upon request. 228 10/02 B43304 Miniaturized – 85 °C Technical data and ordering codes UR VDC 200 CR 100 Hz 20 °C µF Case dimensions d×l mm ESRtyp 100 Hz 20 °C mΩ Zmax 10 kHz 20 °C mΩ 330 390 22 × 25 22 × 30 470 400 560 480 390 470 25 × 25 22 × 35 400 330 480 400 I~R1) 100 Hz 85 °C A Ordering code2) 2,7 3,1 1,2 1,4 B43304A2337M000 B43304A2397M000 3,2 3,6 1,4 1,6 B43304B2397M000 B43304A2477M000 I~max 100 Hz 40 °C A 470 25 × 30 330 400 3,7 1,7 B43304B2477M000 560 22 × 35 280 330 4,0 1,8 B43304A2567M000 560 25 × 30 280 330 4,1 1,8 B43304B2567M000 680 22 × 40 230 280 4,6 2,1 B43304A2687M000 680 680 25 × 35 30 × 25 230 230 280 280 4,7 4,6 2,1 2,1 B43304B2687M000 B43304C2687M000 820 820 22 × 45 25 × 40 190 190 230 230 5,3 5,5 2,4 2,5 B43304A2827M000 B43304B2827M000 820 820 30 × 30 35 × 25 190 190 230 230 5,4 5,6 2,4 2,6 B43304C2827M000 B43304D2827M000 1 000 1 000 25 × 45 30 × 35 160 160 190 190 6,3 6,2 2,9 2,8 B43304A2108M000 B43304B2108M000 1 000 1 200 35 × 30 25 × 50 160 130 190 160 6,6 7,2 3,0 3,3 B43304C2108M000 B43304A2128M000 1 200 30 × 40 130 160 7,2 3,3 B43304B2128M000 1 200 35 × 30 130 160 7,2 3,3 B43304C2128M000 1 500 30 × 45 110 130 8,4 3,8 B43304A2158M000 1 500 1 800 35 × 35 30 × 50 110 90 130 110 8,5 8,7 3,9 4,0 B43304B2158M000 B43304A2188M000 1 800 2 200 35 × 40 35 × 45 90 70 110 90 8,9 10,2 4,0 4,6 B43304B2188M000 B43304A2228M000 1) 120 Hz conversion factor of ripple current: I~ (120 Hz) = 1,03 · I~ (100 Hz) 2) Ordering code for standard terminals (6,3 mm). To determine the ordering code for short terminals (4,5 mm) and 3 terminals (4,5 mm) see page 226. 229 10/02 B43304 Miniaturized – 85 °C Technical data and ordering codes UR VDC 250 CR 100 Hz 20 °C µF Case dimensions d×l mm ESRtyp 100 Hz 20 °C mΩ Zmax 10 kHz 20 °C mΩ 220 270 22 × 25 22 × 30 700 570 840 690 330 330 22 × 30 25 × 25 470 470 560 560 I~R1) 100 Hz 85 °C A Ordering code2) 2,2 2,6 1,0 1,2 B43304E2227M000 B43304E2277M000 2,9 2,9 1,3 1,3 B43304E2337M000 B43304G2337M000 I~max 100 Hz 40 °C A 390 22 × 35 400 480 3,3 1,5 B43304E2397M000 390 25 × 30 400 480 3,4 1,5 B43304G2397M000 470 22 × 40 330 400 3,8 1,7 B43304E2477M000 470 25 × 35 330 400 3,9 1,8 B43304G2477M000 470 560 30 × 25 22 × 45 330 280 400 330 3,8 4,4 1,7 2,0 B43304H2477M000 B43304E2567M000 560 560 25 × 35 30 × 30 280 280 330 330 4,3 4,4 1,9 2,0 B43304G2567M000 B43304H2567M000 680 680 22 × 50 25 × 40 230 230 280 280 5,0 5,0 2,3 2,3 B43304E2687M000 B43304G2687M000 680 680 30 × 30 35 × 25 230 230 280 280 4,9 5,1 2,2 2,3 B43304H2687M000 B43304J2687M000 820 820 25 × 45 30 × 35 190 190 230 230 5,7 5,7 2,6 2,6 B43304E2827M000 B43304G2827M000 820 35 × 30 190 230 6,0 2,7 B43304H2827M000 1 000 30 × 40 160 190 6,6 3,0 B43304E2108M000 1 000 35 × 35 160 190 6,9 3,1 B43304G2108M000 1 200 30 × 45 130 160 7,5 3,4 B43304E2128M000 1 200 1 500 1 800 35 × 35 35 × 45 35 × 50 130 110 90 160 130 110 7,6 8,4 9,6 3,4 3,8 4,4 B43304G2128M000 B43304E2158M000 B43304E2188M000 1) 120 Hz conversion factor of ripple current: I~ (120 Hz) = 1,03 · I~ (100 Hz) 2) Ordering code for standard terminals (6,3 mm). To determine the ordering code for short terminals (4,5 mm) and 3 terminals (4,5 mm) see page 226. 230 10/02 B43304 Miniaturized – 85 °C Technical data and ordering codes UR VDC 400 CR 100 Hz 20 °C µF Case dimensions d×l mm ESRtyp 100 Hz 20 °C mΩ Zmax 10 kHz 20 °C mΩ I~max 100 Hz 40 °C A I~R1) 100 Hz 85 °C A Ordering code2) 100 120 22 × 25 22 × 30 1 630 1 360 1 960 1 630 1,5 1,7 0,67 0,79 B43304A9107M000 B43304A9127M000 120 150 25 × 25 22 × 35 1 360 1 090 1 630 1 310 1,8 2,0 0,80 0,93 B43304B9127M000 B43304A9157M000 150 25 × 30 1 090 1 310 2,1 0,95 B43304B9157M000 180 22 × 40 910 1 090 2,4 1,1 B43304A9187M000 180 25 × 30 910 1 090 2,3 1,0 B43304B9187M000 180 30 × 25 910 1 090 2,4 1,1 B43304C9187M000 220 220 22 × 45 25 × 35 740 740 890 890 2,7 2,7 1,2 1,2 B43304A9227M000 B43304B9227M000 220 270 30 × 30 22 × 50 740 610 890 730 2,8 3,2 1,3 1,4 B43304C9227M000 B43304A9277M000 270 270 25 × 40 30 × 30 610 610 730 730 3,1 3,1 1,4 1,4 B43304B9277M000 B43304C9277M000 270 330 35 × 25 25 × 45 610 500 730 600 3,2 3,6 1,5 1,6 B43304D9277M000 B43304A9337M000 330 330 30 × 35 35 × 30 500 500 600 600 3,6 3,8 1,6 1,7 B43304B9337M000 B43304C9337M000 390 25 × 50 420 510 4,1 1,9 B43304A9397M000 390 30 × 40 420 510 4,1 1,9 B43304B9397M000 390 35 × 30 420 510 4,1 1,9 B43304C9397M000 470 30 × 45 350 420 4,7 2,1 B43304A9477M000 470 560 560 35 × 35 30 × 50 35 × 40 350 300 300 420 350 350 4,7 5,3 5,4 2,2 2,4 2,5 B43304B9477M000 B43304A9567M000 B43304B9567M000 680 35 × 45 240 290 6,2 2,8 B43304A9687M000 1) 120 Hz conversion factor of ripple current: I~ (120 Hz) = 1,03 · I~ (100 Hz) 2) Ordering code for standard terminals (6,3 mm). To determine the ordering code for short terminals (4,5 mm) and 3 terminals (4,5 mm) see page 226. 231 10/02 B43304 Miniaturized – 85 °C Technical data and ordering codes UR VDC 450 CR 100 Hz 20 °C µF Case dimensions d×l mm ESRtyp 100 Hz 20 °C mΩ Zmax 10 kHz 20 °C mΩ I~max 100 Hz 40 °C A I~R1) 100 Hz 85 °C A Ordering code2) 82 100 22 × 25 22 × 30 1 990 1 630 2 390 1 960 1,3 1,6 0,61 0,72 B43304A5826M000 B43304A5107M000 100 120 25 × 25 22 × 35 1 630 1 360 1 960 1 630 1,6 1,8 0,73 0,83 B43304B5107M000 B43304A5127M000 120 25 × 30 1 360 1 630 1,9 0,85 B43304B5127M000 150 22 × 40 1 090 1 310 2,2 0,98 B43304A5157M000 150 25 × 30 1 090 1 310 2,1 0,95 B43304B5157M000 150 30 × 25 1 090 1 310 2,2 0,98 B43304C5157M000 180 180 22 × 45 25 × 35 910 910 1 090 1 090 2,5 2,4 1,1 1,1 B43304A5187M000 B43304B5187M000 180 220 30 × 30 22 × 50 910 740 1 090 890 2,5 2,9 1,1 1,3 B43304C5187M000 B43304A5227M000 220 220 25 × 40 30 × 30 740 740 890 890 2,8 2,8 1,3 1,3 B43304B5227M000 B43304C5227M000 220 270 35 × 25 25 × 45 740 610 890 730 2,9 3,3 1,3 1,5 B43304D5227M000 B43304A5277M000 270 270 30 × 35 35 × 30 610 610 730 730 3,2 3,4 1,5 1,6 B43304B5277M000 B43304C5277M000 330 30 × 40 500 600 3,8 1,7 B43304A5337M000 330 35 × 35 500 600 4,0 1,8 B43304B5337M000 390 30 × 45 420 510 4,3 1,9 B43304A5397M000 390 35 × 35 420 510 4,3 2,0 B43304B5397M000 470 470 560 30 × 50 35 × 40 35 × 45 350 350 300 420 420 350 4,9 5,0 5,6 2,2 2,3 2,6 B43304A5477M000 B43304B5477M000 B43304A5567M000 1) 120 Hz conversion factor of ripple current: I~ (120 Hz) = 1,03 · I~ (100 Hz) 2) Ordering code for standard terminals (6,3 mm). To determine the ordering code for short terminals (4,5 mm) and 3 terminals (4,5 mm) see page 226. 232 10/02 B43304 Miniaturized – 85 °C Useful life depending on ambient temperature TA under ripple current operating conditions 1) KAL0815-C 2,5 Ι~ Ι ~R B43304 2,0 1,5 70 80 ˚C TA 90 Frequency characteristics of ESR Typical behavior Frequency factor of permissible ripple current I~ versus frequency f Ι ~f 2 000 h 60 50 5 000 h 10 000 h 0 40 50 000 h 100 000 h 0,5 25 000 h 1,0 KAL0816-K 1,5 B43304 Ι ~100 Hz KAL0817-T 2,5 B43304 ESR f ESR 100 Hz 2,0 1,3 1,5 1,2 1,1 1,0 20 ˚C 1,0 0,5 > 60 ˚C 0,9 0,8 5 10 2 5 0 1 10 10 3 Hz 2 f 5 10 2 1) Refer to page 40 for an explanation on how to interpret the useful life graphs. 233 10/02 5 10 3 Hz 10 4 f B43304 Miniaturized – 85 °C Impedance Z versus frequency f Typical behavior at 20 °C KAL0818-2 10 2 B43304 Ω Z 10 1 10 0 560 µF/450 V 680 µF/400 V 1800 µF/250 V 10 10 _1 _2 10 1 10 2 10 3 10 4 10 5 Hz 10 6 f 234 10/02 Herausgegeben von EPCOS AG Unternehmenskommunikation, Postfach 80 17 09, 81617 München, DEUTSCHLAND ++49 89 636 09, FAX (0 89) 636-2 26 89 ( EPCOS AG 2002. Vervielfältigung, Veröffentlichung, Verbreitung und Verwertung dieser Broschüre und ihres Inhalts ohne ausdrückliche Genehmigung der EPCOS AG nicht gestattet. Bestellungen unterliegen den vom ZVEI empfohlenen Allgemeinen Lieferbedingungen für Erzeugnisse und Leistungen der Elektroindustrie, soweit nichts anderes vereinbart wird. Diese Broschüre ersetzt die vorige Ausgabe. Fragen über Technik, Preise und Liefermöglichkeiten richten Sie bitte an den Ihnen nächstgelegenen Vertrieb der EPCOS AG oder an unsere Vertriebsgesellschaften im Ausland. Bauelemente können aufgrund technischer Erfordernisse Gefahrstoffe enthalten. Auskünfte darüber bitten wir unter Angabe des betreffenden Typs ebenfalls über die zuständige Vertriebsgesellschaft einzuholen. Published by EPCOS AG Corporate Communications, P.O. Box 80 17 09, 81617 Munich, GERMANY ++49 89 636 09, FAX (0 89) 636-2 26 89 ( EPCOS AG 2002. Reproduction, publication and dissemination of this brochure and the information contained therein without EPCOS’ prior express consent is prohibited. Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical and Electronics Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers’ Association), unless otherwise agreed. This brochure replaces the previous edition. For questions on technology, prices and delivery please contact the Sales Offices of EPCOS AG or the international Representatives. Due to technical requirements components may contain dangerous substances. For information on the type in question please also contact one of our Sales Offices.