0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors FH33 Series Increased FPC retention force 1.2mm ●Small size 2.5mm [ 30 pos. ] 17mm Metal fittings (Leadless) ■Features ●Can be mounted over conductive traces. 1. Low-profile, small PCB mounting area Narrow width of only 2.5 mm reduced the board footprint by approximately 17% to 57%, as compared to several similar FH Series HRS connectors. 2. Various contact pitch (0.4mm, 0.5mm, 1mm pitch) available In addition to standard 0.5mm pitch, 0.4mm pitch, 1mm pitch also available. 3. Increased FPC/FFC retention force _ In the horizontal direction: Approximately 2.0 times (compared to 0.5mm pitch FH12 series.) _ In the vertical direction: Approximately 1.7 times (compared to 0.5mm pitch FH19 series.) No exposed contacts on the bottom of the connector ●Simple operation 1 Open the actuator 2 Insert FPC Actuator 4. Conductive traces on the PCB can run under the connector 1 No exposed contacts on the bottom of the connector. 5. One finger operation of the actuator Proven (in several other Hirose’s connectors) Flip-Lock® rotating actuator assures reliable mechanical and electrical connection with FPC/FFC, confirming it with a definite tactile feel. 2 FPC 6. Easy FPC insertion and reliable electrical connection Proven Flip Lock actuator allows easy insertion of FPC/FFC and provides a tactile sensation when fully closed, confirming complete electrical and mechanical connection. 7. Accepts standard FPC thickness 0.3mm thick standard Flexible Printed Circuit (FPC) and Flexible Flat Cable (FFC) can be used. 8. Board placement with automatic equipment ●Locked condition 3 Close the actuator 4 FPC connected 3 Flat upper surface and tape and reel packaging facilitate vacuum pick-up and placement. Standard reel packaging contains 5000 connectors. 9. Halogen-free* (FH33J Series) 3 4 *As defined by IEC61249-2-21 Br-900ppm maximum, Cl-900ppm maximum, Cl + Br combined-1,500ppm maximum 2007.4 2012.3 1 FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors ■Product Specifications Current rating 0.5 A (0.4mm pitch type 0.4A) Voltage rating 50 V AC (0.4mm pitch type 40V AC) Ratings Operating temperature range -55 ç to +85ç (Note 1) Storage temperature range -10ç to +50ç (Note 2) Operating humidity range Relative humidity 90% max. Storage humidity range Relative humidity 90% max. (No condensation) (No condensation) Thickness = 0.3 ± 0.05mm gold plated (under 30 pos.), 0.3 ± 0.03mm gold plated (over 31 pos.) Recommended FPC Item Specification Conditions 1. Insulation resistance 500 Mø min. 100 V DC 2. Withstanding voltage No flashover or insulation breakdown. 150 V AC /one minute, 120 V AC /one minute(0.4mm pitch type) 3. Contact resistance 50 mø max. 100 mø max(0.4mm pitch type). * Including FPC conductor resistance 1 mA 4. Durability (insertion/ withdrawal) Contact resistance: 50 mø max. 100 mø max(0.4mm pitch type). No damage, cracks, or parts dislocation. 20 cycles No electrical discontinuity of 1µs or more. Contact resistance: 50 mø max. 100 mø max(0.4mm pitch type). No damage, cracks, or parts dislocation. 5. Vibration 6. Shock 7. Humidity (Steady state) Contact resistance: 50 mø max. 100 mø max(0.4mm pitch type). Insulation resistance: 50 Mø min. No damage, cracks, or parts dislocation. 8. Temperature cycle 9. Resistance to soldering heat No deformation of components affecting performance. Frequency: 10 to 55 Hz, single amplitude of 0.75 mm, 10 cycles in each of the 3 directions. Acceleration of 981 m/s2, 6 ms duration, sine half-wave waveform, 3 cycles in each of the 3 axis 96 hours at 40ç and humidity of 90% to 95%. Temperature : -55ç/+15ç to +35ç/+85ç/+15ç to +35ç Time : 30 / 2 to 3 / 30 / 2 to 3 (Minutes) 5 cycles Reflow : At the recommended temperature profile Manual soldering: 350ç ± 10ç for 5 seconds Note 1: Includes temperature rise caused by current flow. Note 2: The term ”storage” refers to products stored for long period of time prior to mounting and use. Operating Temperature Range and Humidity range covers non- conducting condition of installed connectors in storage, shipment or during transportation. Note 3: Information contained in this catalog represents general requirements for this Series. Contact us for the drawings and specifications for a specific part number shown. ■Materials Part Material Finish Color:Beige Color:Deep brown Color:Beige Color:Black Color:Beige Color:Deep brown Color:Beige Color:Black Gold flash plated Pure tin reflow plated PA FH33 series LCP PPS LCP PA LCP PPS FH33J series Insulator FH33M series FH33MHJ series Contacts Metalfittings Phosphor bronze Remarks UL94V-0 --------- ■Ordering information FH 33 M H J - 12 (6) S B - 1 SH (10) 1 2 3 4 5 6 7 8 9 10 11 12 1 Series name:FH 4 Blank:Width 3.0mm(standard) 7 Standard type:Blank 10 Contact pitch: H:Width 3.5mm(long actuator type) Eccentric type:Nomber of contacts 0.4mm,0.5mm,1mm 2 Series No:33 3 Blank:0.5mm pitch,1mm pitch 5 Blank:Standard 8 Contact alignment:S: single 11 SH:SMT horizontal mounting M:0.4mm pitch J:Halogen-free 9 Eccentric direction: 12 Plating specifications: Flame retardance UL94V-0 6 Standard type:Nomber of contacts Eccentric type:Number of contacts in 1mm housing 2 Blank:standard type B:Eccentric type Blank:Gold plated (10) Gold plated with nickel barrier FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors ■Connector Dimensions ●0.4mm pitch, 0.5mm pitch type A±0.15 B G (1) T ∞Number of contacts (0.15) 0.15 G 2.25±0.15 Lot No. indicator U A** Polarizing mark indicator Number of contacts indicator (0.15) F (C: FPC insertion slot dimension) D±0.1 0.35±0.1 The coplanarity of each terminal lead is within 0.1 max. The contact terminal lead position indicates the dimension from the bottom a surface of the insulator body. Difference of each terminal lead is within 0.1 max. Slight variations in color of the plastic compounds do not affect form, fit or function of the connector. 6 After reflow, the terminal plating may change color, however this does not represent a quality issue. (1.8) Notes 1 2 3 4 5 1 2 0 0.5±0.1 a (1.1) 0.15MAX 0.55±0.1 1.73±0.2 2.2±0.15 1.2±0.1 (1 20 ˚) F 0.25±0.1 0 0.15MAX 1 2 0.3+0.15 3 – 0.1 Unit: mm Part Number CL No. Number of Contacts A B C D T U FH33-6S-0.5SH (**) FH33-9S-0.5SH (**) FH33-10S-0.5SH (**) FH33-12S-0.5SH (**) FH33-14S-0.5SH (**) FH33-19S-0.5SH (**) FH33-20S-0.5SH (**) FH33-26S-0.5SH (**) FH33-28S-0.5SH (**) FH33-30S-0.5SH (**) FH33-32S-0.5SH (**) FH33-36S-0.5SH (**) FH33-40S-0.5SH (**) FH33-45S-0.5SH (**) FH33M-16S-0.4SH (**) FH33J-4S-0.5SH (**) FH33J-10S-0.5SH (**) FH33J-12S-0.5SH (**) FH33J-16S-0.5SH (**) FH33J-18S-0.5SH (**) FH33J-19S-0.5SH (**) FH33J-40S-0.5SH (**) FH33MHJ-65S-0.4SH (**) 580-1301-1-** 580-1303-7-** 580-1304-0-** 580-1302-4-** 580-1305-2-** 580-1307-8-** 580-1317-1-** 580-1306-5-** 580-1300-9-** 580-1312-8-** 580-1310-2-** 580-1311-5-** 580-1308-0-** 580-1316-9-** 580-1319-7-** 580-1329-0-** 580-1324-7-** 580-1328-8-** 580-1331-2-** 580-1334-0-** 580-1332-5-** 580-1330-0-** 580-1325-0-** 6 9 10 12 14 19 20 26 28 30 32 36 40 45 16 4 10 12 16 18 19 40 65 5 6.5 7 8 9 11.5 12 15 16 17 18 20 22 24.5 8.3 4 7 8 10 11 11.5 22 27.9 2.5 4 4.5 5.5 6.5 9 9.5 12.5 13.5 14.5 15.5 17.5 19.5 22 6 1.5 4.5 5.5 7.5 8.5 9 19.5 25.6 3.57 5.07 5.57 6.57 7.57 10.07 10.57 13.57 14.57 15.57 16.57 18.57 20.57 23.07 6.87 2.57 5.57 6.57 8.57 9.57 10.07 20.57 26.47 4.35 5.85 6.35 7.35 8.35 10.85 11.35 14.35 15.35 16.35 17.35 19.35 21.35 23.85 7.65 3.35 6.35 7.35 9.35 10.35 10.85 21.35 27.25 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.4 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.4 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.45 0.95 Note 1: (**) : Plating specification. Refer to ordering information. Note 2: Tape-and-reel packaging (5,000 pieces/reel). Order by number of reels. 3 FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors ■Connector Dimensions ●1mm pitch type A±0.15 （1.75） B 1 G ∞Number of contacts （0.15） 0.15 G （1） Lot No. indicator HRS mark （0.45） A＊＊ △ Polarizing mark indicator 2.25±0.15 （V） Cav No. Number of contacts indicator （0.15） (C: FPC insertion slot dimension) D±0.1 F 0.35±0.1 (1.8) Notes 1 2 3 4 5 The coplanarity of each terminal lead is within 0.1 max. The contact terminal lead position indicates the dimension from the bottom a surface of the insulator body. Difference of each terminal lead is within 0.1 max. Slight variations in color of the plastic compounds do not affect form, fit or function of the connector. 6 After reflow, the terminal plating may change color, however this does not represent a quality issue. 1 2 0 0.5±0.1 a (1.1) 0.15MAX 0.55±0.1 1.73±0.2 2.2±0.15 1.2±0.1 F 0.25±0.1 0 0.15MAX 1 2 0.3+0.15 3 _0.1 Unit: mm Part Number CL No. Number of Contacts 4 FH33-4S-1SH(**) 580-1322-1-** 580-1323-4-** 6 FH33-12(6)SB-1SH(**) 580-1326-2-** 6 FH33J-12(6)SB-1SH(**) Note 1: (**) : Plating specification. Refer to ordering information. Note 2: Tape-and-reel packaging (5,000 pieces/reel). Order by number of reels. 4 A B C D V 6.5 8 8 3 5 5 5.07 6.57 6.57 5.85 7.35 7.35 1.75 1.25 1.25 FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors ■Recommended PCB mounting pattern and metal mask dimensions 0.65±0.05 ●0.4mm pitch, 0.5mm pitch type B H (0.2) 0.25±0.05(Metal mask) (2.15) (0.15) (0.15) 0.8±0.05 (0.2) (2.45) 0.1 H 2.8±0.05 T ∞Number of contacts 0.3±0.05(Land) J±0.1 (0.2) K±0.1 (A) *Recommended metal mask thickness = 0.1mm ■Recommended FPC dimensions ●0.4mm pitch, 0.5mm pitch type L±0.05 R0 <under 30 pos.>0.3±0.05 <over 31 pos.>0.3±0.03 E 3.3MIN(Stiffener) 2- 0.35±0.03(FPC) 0.3±0.03(FFC) 0.27±0.03(0.4mm pitch) 2.3±0.3(Exposed area) T±0.03 .2 B±0.03 T±0.07 Note 1: If the stiffener is less than 3.3 mm, E dimension must be 0.5 mm min. Unit: mm Part Number CL No. Number of Contacts A B J K L T FH33-6S-0.5SH (**) FH33-9S-0.5SH (**) FH33-10S-0.5SH (**) FH33-12S-0.5SH (**) FH33-14S-0.5SH (**) FH33-19S-0.5SH (**) FH33-20S-0.5SH (**) FH33-26S-0.5SH (**) FH33-28S-0.5SH (**) FH33-30S-0.5SH (**) FH33-32S-0.5SH (**) FH33-36S-0.5SH (**) FH33-40S-0.5SH (**) FH33-45S-0.5SH (**) FH33M-16S-0.4SH (**) FH33J-4S-0.5SH (**) FH33J-10S-0.5SH (**) FH33J-12S-0.5SH (**) FH33J-16S-0.5SH (**) FH33J-18S-0.5SH (**) FH33J-19S-0.5SH (**) FH33J-40S-0.5SH (**) FH33MHJ-65S-0.4SH (**) 580-1301-1-** 580-1303-7-** 580-1304-0-** 580-1302-4-** 580-1305-2-** 580-1307-8-** 580-1317-1-** 580-1306-5-** 580-1300-9-** 580-1312-8-** 580-1310-2-** 580-1311-5-** 580-1308-0-** 580-1316-9-** 580-1319-7-** 580-1329-0-** 580-1324-7-** 580-1328-8-** 580-1331-2-** 580-1334-0-** 580-1332-5-** 580-1330-0-** 580-1325-0-** 6 9 10 12 14 19 20 26 28 30 32 36 40 45 16 4 10 12 16 18 19 40 65 5 6.5 7 8 9 11.5 12 15 16 17 18 20 22 24.5 8.3 4 7 8 10 11 11.5 22 27.9 2.5 4 4.5 5.5 6.5 9 9.5 12.5 13.5 14.5 15.5 17.5 19.5 22 6 1.5 4.5 5.5 7.5 8.5 9 19.5 25.6 3.8 5.3 5.8 6.8 7.8 10.3 10.8 13.8 14.8 15.8 16.8 18.8 20.8 23.3 7.1 2.8 5.8 6.8 8.8 9.8 10.3 20.8 26.7 4.9 6.4 6.9 7.9 8.9 11.4 11.9 14.9 15.9 16.9 17.9 19.9 21.9 24.4 8.2 3.9 6.9 7.9 9.9 10.9 11.4 21.9 27.8 3.5 5 5.5 6.5 7.5 10 10.5 13.5 14.5 15.5 16.5 18.5 20.5 23 6.8 2.5 5.5 6.5 8.5 9.5 10 20.5 26.4 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.4 0.5 0.5 0.5 0.5 0.5 0.5 0.5 0.4 5 FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors ■Recommended PCB mounting pattern and metal mask dimensions ●1mm pitch type （0.2） 2.8±0.05 （0.15） 0.1 H （2.45） 1 H 0.3±0.05(Land) 0.25±0.05(Metal mask) 0.8±0.05 （0.2） W±0.1 1.15±0.1 （0.2） （0.15） ∞Number of contacts （2.15） 0.65±0.05 B J±0.1 K±0.1 （A） *Recommended metal mask thickness = 0.1mm ■Recommended FPC dimensions ●1mm pitch type L±0.1 X±0.1 B±0.1 1±0.1 <under 30 pos.>0.3±0.05 <over 31 pos.>0.3±0.03 0.65±0.1 1±0.1 .2 R0 E 3.3MIN(Stiffener) 2.3±0.3(Exposed area) 2- Unit: mm Part Number FH33-4S-1SH(**) FH33-12(6)SB-1SH(**) FH33J-12(6)SB-1SH(**) 6 CL No. Number of Contacts A B J K L W X 580-1322-1-** 580-1323-4-** 580-1326-2-** 4 6 6 6.5 8 8 3 5 5 5.3 6.8 6.8 6.4 7.9 7.9 5 6.5 6.5 1.15 0.65 0.65 1 0.5 0.5 FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors ■FH33 Series FPC/FFC Construction (Recommended Specifications) 1. Using Single-sided FPC Material Material Name Covering film layer Cover adhesive Surface treatment Copper foil Base adhesive Base film Reinforcement material adhesive Stiffener Thickness (µm) (25) (25) Polyimide 1 mil thick Nickel under plated 1 to 5µm / Gold plated 0.2µm 3 Cu 1oz Heat-hardened adhesive Polyimide 1 mil thick Heat-hardened adhesive Polyimide 7 mil thick Total 35 25 25 30 175 293 2. Using Double-sided FPC Material Material Name Covering film layer Cover adhesive Surface treatment Through-hole copper Copper foil Base adhesive Base film Base adhesive Copper foil Cover adhesive Covering film layer Reinforcement material adhesive Stiffener Thickness (µm) Polyimide 1 mil thick (25) (25) Nickel under plated 1 to 5µm / Gold plated 0.2µm 3 Cu Cu 1/2oz Heat-hardened adhesive Polyimide 1 mil thick Heat-hardened adhesive Cu 1/2oz 15 18 18 25 18 18 25 25 50 100 297 Polyimide 1 mil thick Heat-hardened adhesive Polyimide 4 mil thick Total 3. Using FFC Material Name Material Thickness (µm) Polyester film (12) polyester thermoplastic type Adhesive Gold plated, soft copper film Adhesive (30) 35 Polyester Polyester 30 12 Adhesive Polyester 30 Stiffener Polyester 188 Total 295 π Practical tolerance of thickness dimension is ±20 µm 4. Precautions 1. This specification is a recommendation for the construction of the FH12 Series FPC and FFC (t=0.3 ± 0.05). 2. For details about the construction, please contact the FPC/FFC manufacturers. 7 FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors ■Packaging Specifications ●Embossed Carrier Tape Dimensions ●Embossed Carrier Tape Dimensions (1) Flat surface for placement with automatic equipment 1.5+0.1 0 (3) (3.8) Unreeling direction Flat surface for placement with automatic equipment (1) Unreeling direction (Ø1 3) ●Reel Dimensions (Ø80) (Ø380) (R:INSIDE) (S:OUTSIDE) End section Blank section (10 pockets min.) Lead section (400 mm min.) Mounting section Embossed carrier tape Blank section (10 pockets min.) Note: 5,000 pieces per reel. Embossed tape 32 mm or wider will have perforated feed holes on two sides. 8 M±0.3 P±0.1 N±0.1 (Q) 1.7+0.15 0 (3) (3.8) M±0.3 (Q) (0.3) N±0.1 8±0.1 8±0.1 (0.3) 1.75±0.1 + 0 0 .1 Ø1 .5 4±0.1 2±0.15 (1.7) Ø1 .5 + 4±0.1 2±0.15 (1.7) 1.75±0.1 (Tape width 32mm and over) 0 0 .1 (Tape width up to 24mm) Top cover tape FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors Unit: mm Part Number CL No. 580-1301-1-** FH33-6S-0.5SH (**) 580-1303-7-** FH33-9S-0.5SH (**) 580-1304-0-** FH33-10S-0.5SH (**) 580-1302-4-** FH33-12S-0.5SH (**) 580-1305-2-** FH33-14S-0.5SH (**) 580-1307-8-** FH33-19S-0.5SH (**) FH33-20S-0.5SH (**) 580-1317-1-** 580-1306-5-** FH33-26S-0.5SH (**) 580-1300-9-** FH33-28S-0.5SH (**) 580-1312-8-** FH33-30S-0.5SH (**) 580-1310-2-** FH33-32S-0.5SH (**) 580-1311-5-** FH33-36S-0.5SH (**) 580-1308-0-** FH33-40S-0.5SH (**) FH33-45S-0.5SH (**) 580-1316-9-** 580-1319-7-** FH33M-16S-0.4SH (**) 580-1329-0-** FH33J-4S-0.5SH (**) 580-1324-7-** FH33J-10S-0.5SH (**) 580-1328-8-** FH33J-12S-0.5SH (**) 580-1331-2-** FH33J-16S-0.5SH (**) 580-1334-0-** FH33J-18S-0.5SH (**) 580-1332-5-** FH33J-19S-0.5SH (**) 580-1330-0-** FH33J-40S-0.5SH (**) 580-1325-0-** FH33MHJ-65S-0.4SH (**) 580-1322-1-** FH33-4S-1SH (**) 580-1323-4-** FH33-12(6)S-1SH (**) 580-1326-2-** FH33J-12(6)S-1SH (**) Note 1: Tape-and-reel packaging (5,000 pieces/reel). Order by number of reels. Number of Contacts M N P Q R S 6 9 10 12 14 19 20 26 28 30 32 36 40 45 16 4 10 12 16 18 19 40 65 4 6 6 16 16 16 16 16 24 24 24 24 24 32 32 44 44 24 16 16 16 24 24 24 44 44 16 16 16 7.5 7.5 7.5 7.5 7.5 11.5 11.5 11.5 11.5 11.5 14.2 14.2 20.2 20.2 11.5 7.5 7.5 7.5 11.5 11.5 11.5 20.2 20.2 7.5 7.5 7.5 ----------------------------------------------------------------------28.4 28.4 40.4 40.4 -------------------------------------------------40.4 40.4 ---------------------- 5.3 6.8 7.3 8.3 9.3 11.8 12.3 15.3 16.3 17.3 18.3 20.3 22.3 24.8 8.6 4.3 7.3 8.3 10.3 11.3 11.8 22.3 28.2 6.8 8.3 8.3 17.4 17.4 17.4 17.4 17.4 25.4 25.4 25.4 25.4 25.4 33.4 33.4 45.4 45.4 25.4 17.4 17.4 17.4 25.4 25.4 25.4 45.4 45.4 17.4 17.4 17.4 21.4 21.4 21.4 21.4 21.4 29.4 29.4 29.4 29.4 29.4 37.4 37.4 49.4 49.4 29.4 21.4 21.4 21.4 29.4 29.4 29.4 49.4 49.4 21.4 21.4 21.4 9 FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors ■Recommended Temperature Profile ●Using Lead-free Solder paste HRS test conditions MAX 250ç Solder method : Reflow, IR/hot air Environment 250 230ç : Room air Solder composition : Paste, 96.5%Sn/3.0%Ag/0.5%Cu Temperature (Senju Metal Industry, Co., Ltd.’s Part Number: M705-221CM5-32-10.5) 200 200ç Test board : Glass epoxy 25mm∞50mm∞0.8mm thick Land dimensions : Contacts lead 0.3mm∞0.65mm Metal fittings 0.55mm∞0.8mm 150 150ç Metal mask (ç) : Contacts lead 0.25mm∞0.65mm∞0.1mm thick Metal fittings 0.55mm∞0.8mm∞0.1mm thick 100 This temperature profile is based on the above conditions. In individual applications the actual temperature may vary, 50 depending on solder paste type, volume/thickness and board 25ç (60 sec.) 90 to 120 sec. (60 sec.) Preheating Sodering manufacturer for specific recommendations. 0 Start Time (Seconds) 10 size/thickness. Consult your solder paste and equipment FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors ■Operation and Precautions Operation 1.FPC insertion procedure. Connector installed on the board. 1 Lift up the actuator. Use thumb or index finger. 2 Fully insert the FPC in the connector parallel to mounting surface, with the exposed conductive traces facing down. FPC conductor surface (Bottom side) 3 Rotate down the actuator until firmly closed. It is critical that the inserted FPC is not moved and remains fully inserted. 2.FPC removal 1 Lift up the actuator. Carefully withdraw the FPC. 11 FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors Precautions Exercise care when handling connectors. Follow recommendations given below. PC board flexing SPC board connector mounting area The connectors are straight within 0.1 mm max. Make sure that the PC board connector mounting area flatness can accept the connector terminals without causing any failure of the solder joints. SHandling before mounting on PCB Insertion of the FPC or operation of the actuator prior to mounting on the PCB is NOT RECOMMENDED. SPC Board handling Exercise caution when handling boards with the connectors installed. Do not apply any forces affecting soldered joints. Connector PCB Precautions When Inserting or Removing FPC Pay attention to the following points when inserting FPC. SActuator operation 1 Do not apply excessive force when opening the actuator prior to FPC insertion. When opening make sure that the force is applied only to the actuator itself, avoiding touching of the contacts. Damege to the contacts Damage to the contacts 2 Axis of rotation 0˚) (12 Axis of rotation Assure free rotation of the actuator 3 The actuator will rotate 120 degrees maximum. Do not force it to rotate further. 12 0° 12 FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors Precautions 4 When operating the actuator, do so at the center portion. 5 As illustrated, do not attempt removal or re- positioning of the actuator. S FPC Insertionq The FPC should be aligned parallel with the board surface and perpendicular with the connector (as shown), then completely inserted. Actuator Perpendicular with the connector FPC To assure correct electrical and mechanical connection do not insert FPC at angle. It must be fully inserted. Make sure that the FPC is NOT MOVED during the closing of the actuator. SFPC Insertionw When inserting the FPC, do not forcefully rub against the bottom surface of the connector insertion entrance. Doing so will result in the contacts and FPC making strong contact and may cause deformation of the contacts, peeling of the FPC conductor, and other problems. Peeling of FPC conductor 13 FH33 Series●0.4mm,0.5 mm,1mm Pitch, 1.2 mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors Precautions SVerification of the fully closed actuator. The actuator should be fully closed (as illustrated) and the FPC held firmly in the connector. Do not press against the actuator when is fully closed. Max force applied to the fully closed actuator should not exceed 1 N. Routing the FPC (FPC fully inserted/ actuator closed) SFPC Load Do not apply force in excess of 0.15N max. in the upward direction (as illustrated). Do not bend the FPC too close to the actuator. Load: 0.15N max. Removing the FPC Rotate the actuator to the open position (maximum open angle of 120°). Carefully withdraw the FPC. 0° 12 Other Precautions SHand Soldering Precautions When hand soldering: 1 Do not perform reflow or hand soldering with the FPC inserted in the connector. 2 Do not apply excessive heat or touch the soldering iron anywhere other than the connector leads. 3 Do not use excessive amount of solder or flux compounds. Operation of the actuator and contacts may be affected by excessive amounts of solder or flux compounds. 14 FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors NOTES : 15 FH33 Series●0.4mm,0.5mm,1mm Pitch, 1.2mm above the board, Flexible Printed Circuit & Flexible Flat Cable ZIF Connectors USA: HIROSE ELECTRIC (U.S.A.), INC. Headquarters 2688 Westhills Court, Simi Valley, CA 93065-6235 Phone : +1-805-522-7958 Fax : +1-805-522-3217 http://www.hiroseusa.com USA: HIROSE ELECTRIC (U.S.A.), INC. San Jose Office 20400 Stevens Creek Blvd., Ste 250, Cupertino, CA 95014 Phone : +1-408-253-9640 Fax : +1-408-253-9641 http://www.hiroseusa.com USA: HIROSE ELECTRIC (U.S.A.), INC. Detroit Office (Automotive) 37677 Professional Center Drive, Suite #100C Livonia, MI 48154 Phone : +1-734-542-9963 Fax : +1-734-542-9964 http://www.hiroseusa.com THE NETHERLANDS: HIROSE ELECTRIC EUROPE B.V. Hogehillweg #8 1101 CC Amsterdam Z-O Phone : +31-20-6557460 Fax : +31-20-6557469 http://www.hiroseeurope.com GERMANY: HIROSE ELECTRIC EUROPE B.V. GERMAN BRANCH Herzog-Carl-Strasse 4 D-73760 Ostfildern (Scharnhauser Park) Phone : +49-711-4560-02-1 Fax : +49-711-4560-02-299 http://www.hirose.de UNITED KINGDOM: HIROSE ELECTRIC EUROPE B.V. UK BRANCH First Floor, St Andrews House, Caldecotte Lake Business Park, Milton Keynes MK7 8LE Phone : +44-1908-369060 Fax : +44-1908-369078 http://www.hirose.co.uk CHINA: HIROSE ELECTRIC (SHANGHAI) CO., LTD. 1601,Henderson Metropolitan,NO.300 ,East Nanjing Road,Huangpu District, Shanghai,China 200001 Phone : +86-21-6391-3355 Fax : +86-21-6391-3335 http://www.hirose-china.com.cn CHINA: HIROSE ELECTRIC (SHANGHAI) CO., LTD. BEIJING BRANCH A1001, Ocean International Center, Building 56# East 4th Ring Middle Road, Chao Yang District, Beijing, 100025 Phone : +86-10-5165-9332 Fax : +86-10-5908-1381 http://www.hirose-china.com.cn CHINA: HIROSE ELECTRIC TECHNOLOGIES (SHENZHEN) CO., LTD. Room 09-13, 19/F, Office Tower Shun Hing Square, Di Wang Commercial Centre 5002, ShenNanDong Road, ShenZhen City, Guangdong Province, 518008 Phone : +86-755-8207-0851 Fax : +86-755-8207-0873 http://www.hirose-china.com.cn HONG KONG: HIROSE ELECTRIC HONGKONG TRADING CO., LTD. Room 1001, West Wing, Tsim Sha Tsui Centre, 66 Mody Road, Tsim Sha Tsui East, Kowloon, Hong Kong Phone : +852-2803-5338 Fax : +852-2591-6560 http://www.hirose-hongkong.com.hk TAIWAN: KOREA: HIROSE KOREA CO., LTD. 1261-10, Jeoungwhang-Dong, Shihung-City, Kyunggi-Do 429-450 Phone : +82-31-496-7000,7124 Fax : +82-31-496-7100 http://www.hirose.co.kr SINGAPORE: HIROSE ELECTRIC SINGAPORE PTE. LTD. 10 Anson Road #26-16 International Plaza 079903 Phone : +65-6324-6113 Fax : +65-6324-6123 http://www.hirose-singapore.com.sg INDIA: HIROSE ELECTRIC SINGAPORE PTE. LTD. BANGALORE LIAISON OFFICE Unit No.03, Ground Floor, Explorer Building International Tech Park Whitefield Road, Bangalore 560066 Karnataka, India Phone : +65-6324-6113 Fax : +65-6324-6123 http://www.hirose-singapore.com.sg ® 16 HIROSE ELECTRIC TAIWAN CO., LTD. 103 8F, No.87, Zhengzhou Rd., Taipei Phone : +886-2-2555-7377 Fax : +886-2-2555-7350 http://www.hirose-taiwan.com.tw 6-3,Nakagawa Chuoh-2-Chome,Tsuzuki-Ku,Yokohama-Shi 224-8540,JAPAN TEL: +81-45-620-3526 Fax: +81-45-591-3726 http://www.hirose.com http://www.hirose-connectors.com The contents of this catalog are current as of date of 03/2012. Contents are subject to change without notice for the purpose of improvements.