Yea Shin ES2C Surface mount superfast rectifier voltage - 50 to 600 volts current - 2.0 ampere Datasheet

DATA SHEET
ES2A Thru ES2J
SEMICONDUCTOR
SURFACE MOUNT SUPERFAST RECTIFIER
VOLTAGE - 50 to 600 Volts CURRENT - 2.0 Ampere
FEATURES
•For surface mounted applications
Unit:inch(mm)
SMA/DO-214AC
•Low profile package
•Built-in strain relief
.062(1.60)
.047(1.20)
•Easy pick and place
•Superfast recovery times for high efficiency
.114(2.90)
.098(2.50)
•Plastic package has Underwriters Laboratory
Flammability Classification 94V-O
•Glass passivated junction
.181 (4.60)
.157(4.00)
•High temperature soldering:
260 OC / 10 seconds at terminals
•High temperature soldering : 260OC / 10 seconds at terminals
•Pb free product at available : 99% Sn above meet RoHS
.096(2.44)
.078(2.00)
environment substance directive request
.012(.305)
.006(.152)
.008(.203 )
.002(.051)
MECHANICAL DATA
.060(1.52)
.030(0.76)
•Case: JEDEC DO-214AA molded plastic
.208(5.28)
.188(4.80)
•Terminals: Solder plated, solderable per
MIL-STD-750, Method 2026
•Polarity: Indicated by cathode band
•Standard packaging: 12mm tape (EIA-481)
•Weight: 0.003 ounce, 0.093 gram
MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS
Ratings at 25 ¢J ambient temperature unless otherwise specified.
Single phase, half wave, 60Hz, resistive or inductive load.
For capacitive load, derate current by 20%.
UNITS
SYMBOLS
ES2A
ES2B
ES2C
ES2D
ES2E
ES2G
ES2J
Maximum Recurrent Peak Reverse Voltage
VRRM
50
100
150
200
300
400
600
Volts
Maximum RMS Voltage
VRMS
35
70
105
140
210
280
420
Volts
Maximum DC Blocking Voltage
VDC
50
100
150
200
300
400
600
Volts
Maximum Average Forward Rectified Current,
I(AV)
2.0
Amps
IFSM
50.0
Amps
at TL=110 OC
Peak Forward Surge Current 8.3ms single half
sinewave superimposed on rated load(JEDEC method)
VF
Maximum Instantaneous Forward Voltage at 2.0A
Maximum DC Reverse Current TA=25 OC
1.25
35.0
CJ
25.0
RθJA
20.0
TJ,TSTG
-55 to +150
Typical Junction capacitance (Note 2)
Typical Thermal Resistance (Note 3)
Volts
uA
100
TRR
Maximum Reverse Recovery Time (Note 1)
1.7
5.0
IR
O
At Rated DC Blocking Voltage TA=100 C
Operating and Storage Temperature Range
0.95
nS
pF
O
C /W
O
C
NOTES:
1. Reverse Recovery Test Conditions: IF=0.5A, IR=1.0A, Irr=0.25A
2. Measured at 1 MHz and Applied reverse voltage of 4.0 volts
3. 8.0mm2 (.013mm thick) land areas
http://www.yeashin.com
1
REV.02 20120705
DEVICE CHARACTERISTICS
ES2A Thru ES2J
AVERAGE FORWARD RECTIFIED
CURRENT, AMPERES
trr
+0.5A
0
-0.25
NOTE:1.Rise Time = 7ns max.
Input Impedance = 1 megohm. 22pF
2.Rise Time = 10ns max.
-1.0
SET TIME
BASE FOR
Source Impedance = 50 Ohms
1cm
2.4
2.0
SINGLE PHASE HALF
WAVE 60Hz RESISTIVE
OR INDUCTIVE LOAD
P.C.B. MOUNTED ON
0.3×0.3"(8.0×8.0mm)
COPPER PAD AREAS
1.6
1.2
0.8
0.4
0
0
20
TJ = 75 OC
T J = 25 OC
1
0.1
20
60
40
80
100
120
120
140
160
50.0
ES2A
10.0
ES2E
1.0
ES2J
0.1
TJ = 25 OC
PULSE WIDTH = 300 ms
2% DUTY CYCLE
0.01
0
100
Fig. 2-MAXIMUM AVERAGE FORWARD
CURRENT RATING
INSTANTANEOUS FORWARD CURRENT
AMPERES
INSTANTANEOUS REVERSE CURRENT,
MICROAMPERES
1,000
10
80
LEAD TEMPERATURE, C
Fig. 1-REVERSE RECOVERY TIME CHARACTERISTIC AND
TEST CIRCUIT DIAGRAM
T J = 100 OC
60
O
50 ns/cm
100
40
140
0.01
0.4
0.8
0.5
1.0
1.2
1.4
1.6 1.8
PERCENT OF RATED PEAK INVERSE VOLTAGE, VOLTS
REVERSE VOLTAGE, VOLTS
Fig. 4-TYPICAL FORWARD CHARACTERISTICS
60
60
50
CAPACITANCE, pF
PEAK FORWARD SURGE CURRENT,
AMPERES
Fig. 3-TYPICAL REVERSE CHARACTERISTICS
8.3ms SINGLE HALF SINE WAVE
JEDEC METHOD
40
30
20
10
50
40
30
TJ = 25 OC
20
f = 1.0MHz
Vsig = 50mVp-p
10
1
5
2
10
20
50
100
NUMBER OF CYCLES AT 60Hz
.5
1
2
5
10
20
50
100 200
500 1000
REVERSE VOLTAGE, VOLTS
Fig. 5-MAXIMUM NON-REPETITIVE PEAK FORWARD
SURGE CURRENT
http://www.yeashin.com
.1
2
Fig. 6-TYPICAL JUNCTION CAPACITANCE
REV.02 20120705
Similar pages