19-4865; Rev 4/11 DS1992/DS1993 1Kb/4Kb Memory iButton SPECIAL FEATURES COMMON iButton FEATURES 4096 bits of Read/Write Nonvolatile Memory (DS1993) 1024 bits of Read/Write Nonvolatile Memory (DS1992) 256-bit Scratchpad Ensures Integrity of Data Transfer Memory Partitioned into 256-bit Pages for Packetizing Data Data Integrity Assured with Strict Read/Write Protocols Operating Temperature Range from -40°C to +70°C Over 10 years of data retention ORDERING INFORMATION DS1992L-F5+ DS1993L-F5+ F5 MicroCan F5 MicroCan +Denotes a lead(Pb)-free/RoHS-compliant product. EXAMPLES OF ACCESSORIES DS9096P Self-Stick Adhesive Pad DS9101 Multipurpose Clip DS9093RA Mounting Lock Ring DS9093F Snap-In Fob DS9092 iButton Probe F5 MicroCan 1-Wire and iButton are registered trademarks of Maxim Integrated Products, Inc. 1 of 17 Unique, Factory-Lasered and Tested 64-bit Registration Number (8-bit Family Code + 48-bit Serial Number + 8-bit CRC Tester) Assures Absolute Traceability Because No Two Parts are Alike Multidrop Controller for MicroLAN Digital Identification and Information by Momentary Contact Chip-Based Data Carrier Compactly Stores Information Data Can be Accessed While Affixed to Object Economically Communicates to Bus Master with a Single Digital Signal at 16.3kbps Standard 16mm Diameter and 1-Wire® Protocol Ensure Compatibility with iButton® Family Button Shape is Self-Aligning with CupShaped Probes Durable Stainless Steel Case Engraved with Registration Number Withstands Harsh Environments Easily Affixed with Self-Stick Adhesive Backing, Latched by its Flange, or Locked with a Ring Pressed onto its Rim Presence Detector Acknowledges When Reader First Applies Voltage Meets UL 913, 5th Ed., Rev. 1997-02-24; Intrinsically Safe Apparatus, Approved under Entity Concept for use in Class I, Division 1, Group A, B, C, and D Locations DS1992/DS1993 iButton DESCRIPTION The DS1992/DS1993 memory iButtons (hereafter referred to as DS199x) are rugged read/write data carriers that act as a localized database, easily accessible with minimal hardware. The nonvolatile memory and optional timekeeping capability offer a simple solution to storing and retrieving vital information pertaining to the object to which the iButton is attached. Data is transferred serially through the 1-Wire protocol that requires only a single data lead and a ground return. The scratchpad is an additional page that acts as a buffer when writing to memory. Data is first written to the scratchpad where it can be read back. After the data has been verified, a copy scratchpad command transfers the data to memory. This process ensures data integrity when modifying the memory. A 48-bit serial number is factory lasered into each DS199x to provide a guaranteed unique identity that allows for absolute traceability. The durable MicroCan package is highly resistant to environmental hazards such as dirt, moisture, and shock. Its compact coin-shaped profile is self-aligning with mating receptacles, allowing the DS199x to be easily used by human operators. Accessories permit the DS199x to be mounted on almost any surface including plastic key fobs, photo-ID badges, and PC boards. Applications include access control, work-in-progress tracking, electronic travelers, storage of calibration constants, and debit tokens. OPERATION The DS199x have three main data components: 1) 64-bit lasered ROM, 2) 256-bit scratchpad, and 3) 1024-bit (DS1992) or 4096-bit (DS1993) SRAM. All data is read and written least significant bit first. The memory functions are not available until the ROM function protocol has been established. This protocol is described in the ROM functions flow chart (Figure 9). The master must first provide one of four ROM function commands: 1) read ROM, 2) match ROM, 3) search ROM, or 4) skip ROM. After a ROM function sequence has been successfully executed, the memory functions are accessible and the master can then provide any one of the four memory function commands (Figure 6). PARASITE POWER The block diagram (Figure 1) shows the parasite-powered circuitry. This circuitry steals power whenever the data input is high. The data line provides sufficient power as long as the specified timing and voltage requirements are met. The advantages of parasite power are two-fold: 1) by parasiting off this input, battery power is not consumed for 1-Wire ROM function commands, and 2) if the battery is exhausted for any reason, the ROM may still be read normally. The remaining circuitry of the DS1992 and DS1993 is solely operated by battery energy. 64-BIT LASERED ROM Each DS199x contain a unique ROM code that is 64 bits long. The first 8 bits are a 1-Wire family code. The next 48 bits are a unique serial number. The last 8 bits are a CRC of the first 56 bits (see Figure 2). The 1-Wire CRC is generated using a polynomial generator consisting of a shift register and XOR gates as shown in Figure 3. The polynomial is X8 + X5 + X4 + 1. Additional information about the Maxim 1-Wire Cyclic Redundancy Check is available in the Book of DS19xx iButton Standards. The shift register bits are initialized to zero. Then starting with the least significant bit of the family code, 1 bit at a time is shifted in. After the 8th bit of the family code has been entered, then the serial number is entered. After the 48th bit of the serial number has been entered, the shift register contains the CRC value. Shifting in the 8 bits of CRC should return the shift register to all zeros. 2 of 17 DS1992/DS1993 Figure 1. DS1992/DS1993 BLOCK DIAGRAM 1-WIRE PORT ROM FUNCTION CONTROL 1-W PARASITEPOWERED CIRCUITRY 64-BIT LASERED ROM MEMORY FUNCTION CONTROL 256-BIT SCRATCHPAD SRAM 16 PAGES of 256BITs (1993) 4 PAGES of 256BITs (1992) 3V LITHIUM Figure 2. 64-BIT LASERED ROM MSB LSB 8-Bit CRC Code MSB 8-Bit Family Code (06h)1993 (08h)1992 48-Bit Serial Number LSB MSB LSB MSB LSB Figure 3. 1-Wire CRC CODE 8 5 4 Polynomial = X + X + X + 1 st nd 1 STAGE X 0 rd 2 STAGE X 1 th 3 STAGE X 2 th 4 STAGE X 3 th X 4 th 6 STAGE 5 STAGE X 5 th 8 STAGE 7 STAGE X 6 X 7 INPUT DATA 3 of 17 X 8 DS1992/DS1993 Figure 4a. DS1993 MEMORY MAP SCRATCHPAD MEMORY NOTE: Each page is 32 bytes (256 bits). The hex values represent the starting address for each page or register. PAGE PAGE 0 0000h PAGE 1 0020h PAGE 2 0040h PAGE 3 0060h PAGE 4 0080h PAGE 5 00A0h PAGE 6 00C0h PAGE 7 00E0h PAGE 8 0100h PAGE 9 0120h PAGE 10 0140h PAGE 11 0160h PAGE 12 0180h PAGE 13 01A0h PAGE 14 01C0h PAGE 15 01E0h Figure 4b. DS1992 MEMORY MAP SCRATCHPAD NOTE: Each page is 32 bytes (256 bits). The hex values represent the starting address for each page or register. PAGE PAGE 0 0000h PAGE 1 0020h PAGE 2 0040h PAGE 3 0060h MEMORY 4 of 17 DS1992/DS1993 MEMORY The memory map in Figure 4 shows a 32-Byte page called the scratchpad, and additional 32-Byte pages called memory. The DS1992 contains pages 0 though 3 that make up the 1024-bit SRAM. The DS1993 contain pages 0 through 15 that make up the 4096-bit SRAM. The scratchpad is an additional page that acts as a buffer when writing to memory. Data is first written to the scratchpad where it can be read back. After the data has been verified, a copy scratchpad command transfers the data to memory. This process ensures data integrity when modifying the memory. MEMORY FUNCTION COMMANDS The Memory Function Flow Chart (Figure 6) describes the protocols necessary for accessing the memory. An example follows the flow chart. Three address registers are provided as shown in Figure 5. The first two registers represent a 16-bit target address (TA1, TA2). The third register is the ending offset/data status byte (E/S). The target address points to a unique Byte location in memory. The first 5 bits of the target address (T4:T0) represent the Byte offset within a page. This Byte offset points to one of 32 possible Byte locations within a given page. For instance, 00000b points to the first Byte of a page where as 11111b would point to the last Byte of a page. The third register (E/S) is a read only register. The first 5 bits (E4: E0) of this register are called the ending offset. The ending offset is a Byte offset within a page (1 of 32 Bytes). Bit 5 (PF) is the partial Byte flag. Bit 6 (OF) is the overflow flag. Bit 7 (AA) is the authorization accepted flag. Figure 5. ADDRESS REGISTERS 7 6 5 4 3 2 1 0 TARGET ADDRESS (TA1) T7 T6 T5 T4 T3 T2 T1 T0 TARGET ADDRESS (TA2) T15 T14 T13 T12 T11 T10 T9 T8 ENDING ADDRESS WITH DATA STATUS (E/S) (READ ONLY) AA OF PF E4 E3 E2 E1 E0 Write Scratchpad Command [0Fh] After issuing the write scratchpad command, the user must first provide the 2-Byte target address, followed by the data to be written to the scratchpad. The data is written to the scratchpad starting at the byte offset (T4:T0). The ending offset (E4:E0) is the Byte offset at which the host stops writing data. The maximum ending offset is 11111b (31d). If the host attempts to write data past this maximum offset, the overflow flag (OF) is set and the remaining data is ignored. If the user writes an incomplete Byte and an overflow has not occurred, the partial Byte flag (PF) is set. Read Scratchpad Command [AAh] This command can be used to verify scratchpad data and target address. After issuing the read scratchpad command, the user can begin reading. The first two Bytes are the target address. The next Byte is the ending offset/data status Byte (E/S) followed by the scratchpad data beginning at the Byte offset (T4: T0). The user can read data until the end of the scratchpad, after which the data read is all logic 1’s. 5 of 17 DS1992/DS1993 Copy Scratchpad [55h] This command is used to copy data from the scratchpad to memory. After issuing the copy scratchpad command, the user must provide a 3-byte authorization pattern. This pattern must exactly match the data contained in the three address registers (TA1, TA2, E/S, in that order). If the pattern matches, the AA (Authorization Accepted) flag is set and the copy begins. A logic 0 is transmitted after the data has been copied until the user issues a reset pulse. Any attempt to reset the part is ignored while the copy is in progress. Copy typically takes 30µs. The data to be copied is determined by the three address registers. The scratchpad data from the beginning offset through the ending offset is copied to memory, starting at the target address. Anywhere from 1 to 32 Bytes can be copied to memory with this command. Whole Bytes are copied even if only partially written. The AA flag is cleared only by executing a write scratchpad command. Read Memory [F0h] The read memory command can be used to read the entire memory. After issuing the command, the user must provide the 2-Byte target address. After the two Bytes, the user reads data beginning from the target address and may continue until the end of memory, at which point logic 1’s are read. It is important to realize that the target address registers contains the address provided. The ending offset/data status Byte is unaffected. The hardware of the DS199x provides a means to accomplish error-free writing to the memory section. To safeguard reading data in the 1-Wire environment and to simultaneously speed up data transfers, it is recommended to packetize data into data packets of the size of one memory page each. Such a packet would typically store a 16-bit CRC with each page of data to ensure rapid, error-free data transfers that eliminate having to read a page multiple times to determine if the received data is correct or not. (See Application Note 114 for the recommended file structure to be used with the 1-Wire environment.) 6 of 17 DS1992/DS1993 Figure 6. MEMORY FUNCTIONS FLOW CHART Master TX Memory Function Command 0FH Write Scratchpad ? Y Bus Master TX TA1 (T7:T0) AAH Read Scratchpad ? Y N Bus Master RX TA2 (T15:T8) DS199x sets Scratchpad Offset = (T4:T0) and Clears (PF, OF, AA) Master RX Ending Offset with Data Status (E/S) DS199x Sets Scratchpad Offset=(T4:T0) Master TX Data Byte To Scratchpad Offset DS199x sets (E4:E0) = Scratchpad Offset DS199x Increments Scratchpad Offset N Scratchpad Offset = 11111b ? Y Y OF = 1 N Bus Master TX Data ? N Second Part Bus Master RX TA1 (T7:T0) Bus Master TX TA2 (T15:T8) Bus Master TX Reset ? N To Figure 6 Master RX Data Byte From Scratchpad Offset Y DS199x Increments Scratchpad Offset N Y Partial Byte Written ? N PF = 1 Bus Master TX Reset ? N Y Scratchpad Offset = 11111b ? Y Bus Master RX "1"s Bus Master TX Reset ? Y From Figure 6 Second Part DS199x TX Presence Pulse (See Figure 9) 7 of 17 DS1992/DS1993 Figure 6. MEMORY FUNCTIONS FLOW CHART (continued) From Figure 6 First Part 55H Copy Scratchpad ? Y F0H Y Read Memory ? N N Bus Master TX TA1 (T7:T0) Bus Master TX TA1 (T7:T0) Bus Master TX TA2 (T15:T8) Bus Master TX TA2 (T15:T8) Bus Master TX E/S Byte Authorization Code Match ? DS199x sets Memory Address = (T15:T0) N Master RX Data Byte From Memory Address Y AA = 1 DS199x TX "1"s DS199x Increments Address Counter DS199x Copies Scratchpad Data To Memory Y Bus Master TX Reset ? N DS199x TX "0"s N N Bus Master TX Reset ? Y Bus Master TX Reset ? Y N To Figure 6 First Part 8 of 17 Memory Address = 21Dh ? Y Bus Master RX "1"s DS1992/DS1993 MEMORY FUNCTION EXAMPLES Example: Write two data Bytes to memory locations 0026h and 0027h (the seventh and eighth Bytes of page 1). Read entire memory. MASTER MODE TX RX TX TX TX TX TX TX RX TX TX RX RX RX RX TX RX TX TX TX TX TX TX RX TX TX TX TX RX TX RX DATA (LSB FIRST) Reset Presence CCh 0Fh 26h 00h <2 data Bytes> Reset Presence CCh Aah 26h 00h 07h <2 data Bytes> Reset Presence CCh 55h 26h 00h 07h Reset Presence CCh F0h 00h 00h <128 Bytes (DS1992)> <512 Bytes (DS1993)> Reset Presence COMMENTS Reset pulse (480µs to 960µs) Presence pulse Issue skip ROM command Issue write scratchpad command TA1, beginning offset = 6 TA2, address = 0026h Write 2 Bytes of data to scratchpad Reset pulse Presence pulse Issue skip ROM command Issue read scratchpad command Read TA1, beginning offset = 6 Read TA2, address = 0026h Read E/S, ending offset = 7, flags = 0 Read scratchpad data and verify Reset pulse Presence pulse Issue skip ROM command Issue copy scratchpad command TA1 TA2 AUTHORIZATION CODE E/S Reset pulse Presence pulse Issue skip ROM command Issue read memory command TA1, beginning offset = 6 TA2, address = 0000h Read entire memory Reset pulse Presence pulse, done 9 of 17 DS1992/DS1993 1-Wire BUS SYSTEM The 1-Wire bus is a system that has a single bus master and one or more slaves. In all instances the DS199x is a slave device. The bus master is typically a microcontroller or PC. For small configurations the 1-Wire communication signals can be generated under software control using a single port pin. For multisensor networks, the DS2480B 1-Wire line driver chip or serial port adapters based on this chip (DS9097U series) are recommended. This simplifies the hardware design and frees the microprocessor from responding in real-time. The discussion of this bus system is broken down into three topics: hardware configuration, transaction sequence, and 1-Wire signaling (signal types and timing). The 1-Wire protocol defines bus transactions in terms of the bus state during specific time slots that are initiated on the falling edge of sync pulses from the bus master. For a more detailed protocol description, refer to Chapter 4 of the Book of DS19xx iButton Standards. HARDWARE CONFIGURATION The 1-Wire bus has only a single line by definition; it is important that each device on the bus be able to drive it at the appropriate time. To facilitate this, each device attached to the 1-Wire bus must have opendrain or three-state outputs. The 1-Wire port of the DS199x is open drain with an internal circuit equivalent to that shown in Figure 8. A multidrop bus consists of a 1-Wire bus with multiple slaves attached. The 1-Wire bus has a maximum data rate of 16.3kbps and requires a pullup resistor of approximately 5kΩ. The idle state for the 1-Wire bus is high. If for any reason a transaction needs to be suspended, the bus must be left in the idle state if the transaction is to resume. If this does not occur and the bus is left low for more than 120µs, one or more of the devices on the bus may be reset. Figure 8. HARDWARE CONFIGURATION BUS MASTER VPUP DS199x 1-Wire PORT RPU RX DATA TX RX = RECEIVE Open Drain Port Pin RX TX 5 µA Typ. TX = TRANSMIT 100 Ω MOSFET TRANSACTION SEQUENCE The protocol for accessing the DS199x through the 1-Wire port is as follows: Initialization ROM Function Command Memory Function Command Transaction/Data INITIALIZATION All transactions on the 1-Wire bus begin with an initialization sequence. The initialization sequence consists of a reset pulse transmitted by the bus master followed by presence pulse(s) transmitted by the 10 of 17 DS1992/DS1993 slave(s). The presence pulse lets the bus master know that the DS199x is on the bus and is ready to operate. For more details, see the 1-Wire Signaling section. ROM FUNCTION COMMANDS Once the bus master has detected a presence, it can issue one of the four ROM function commands. All ROM function commands are 8 bits long. A list of these commands follows (see the flow chart in Figure 9). Read ROM [33h] This command allows the bus master to read the DS199x’s 8-bit family code, unique 48-bit serial number, and 8-bit CRC. This command should only be used if there is a single DS199x on the bus. If more than one slave is present on the bus, a data collision occurs when all slaves try to transmit at the same time (open drain produces a wired-AND result). The resultant family code and 48-bit serial number usually result in a mismatch of the CRC. Match ROM [55h] The match ROM command, followed by a 64-bit ROM sequence, allows the bus master to address a specific DS199x on a multidrop bus. Only the DS199x that exactly matches the 64-bit ROM sequence will respond to the following memory function command. All slaves that do not match the 64-bit ROM sequence wait for a reset pulse. This command can be used with single or multiple devices on the bus. Skip ROM [CCh] This command can save time in a single drop bus system by allowing the bus master to access the memory functions without providing the 64-bit ROM code. If more than one slave is present on the bus and, for example, a read command is issued following the Skip ROM command, data collision will occur on the bus as multiple slaves transmit simultaneously (open-drain pulldowns produce a wired-AND result). Search ROM [F0h] When a system is initially brought up, the bus master may not know the number of devices on the 1-Wire bus or their 64-bit ROM codes. The search ROM command allows the bus master to use a process of elimination to identify the 64-bit ROM codes of all slave devices on the bus. The search ROM process is the repetition of a simple 3-step routine: read a bit, read the complement of the bit, then write the desired value of that bit. The bus master performs this simple, 3-step routine on each bit of the ROM. After one complete pass, the bus master knows the 64-bit ROM code of one device. Additional passes will identify the ROM codes of the remaining devices. See Chapter 5 of the Book of DS19xx iButton Standards for a comprehensive discussion of a search ROM, including an actual example. 1-Wire SIGNALING The DS199x require strict protocols to ensure data integrity. The protocol consists of four types of signaling on one line: reset sequence with reset pulse and presence pulse, write 0, write 1, and read data. The bus master initiates all these signals except presence pulse. The initialization sequence required to begin any communication with the DS199x is shown in Figure 10. A reset pulse followed by a presence pulse indicates the DS199x is ready to send or receive data given the correct ROM command and memory function command. The bus master transmits (Tx) a reset pulse (tRSTL, minimum 480µs). The bus master then releases the line and goes into receive mode (Rx). The 1-Wire bus is pulled to a high state through the pullup resistor. After detecting the rising edge on the data line, the DS199x waits (tPDH, 15µs to 60µs) and then transmits the presence pulse (tPDL, 60µs to 240µs). 11 of 17 DS1992/DS1993 Figure 9. ROM FUNCTIONS FLOW CHART Master TX Reset Pulse DS199x TX Presence Pulse Master TX ROM Function Command 33H Read ROM Command ? Y DS199x TX Family Code 1 Byte N 55H Match ROM Command ? F0H Search ROM Command ? Y N Y DS199x TX Bit 0 Master TX Bit 0 DS199x TX Bit 0 Master TX Bit 0 Bit 0 Match ? N N Bit 0 Match ? Y Y DS199x TX Serial Number 6 Bytes N DS199x TX Bit 1 Master TX Bit 1 DS199x TX Bit 1 Master TX Bit 1 Bit 1 Match ? N N Bit 1 Match ? Y Y DS199x TX Bit 63 DS199x TX CRC Byte DS199x TX Bit 63 Master TX Bit 63 Master TX Bit 63 Bit 63 Match ? N N Bit 63 Match ? Y Y Master TX Memory Function Command 12 of 17 CCH Skip ROM Command ? Y N DS1992/DS1993 Figure 10. INITIALIZATION PROCEDURE RESET AND PRESENCE PULSE MASTER TX "RESET PULSE" MASTER RX "PRESENCE PULSE" tRSTH VPULLUP VPULLUP MIN VIH MIN VIL MAX 0V tR tRSTL RESISTOR MASTER DS199x tPDH 480 µs ≤ tRSTL < ∞* 480 µs ≤ tRSTH < ∞** 15 µs ≤ tPDH < 60 µs tPDL * In order not to mask interrup signaling by other devices on the 10Wire bus tRSTL + tR should always be less than 960 us ** Includes recovery time 60 ≤ tPDL < 240 µs READ/WRITE TIME SLOTS The definitions of write and read time slots are illustrated in Figure 11. The master driving the data line low initiates all time slots. The falling edge of the data line synchronizes the DS199x to the master by triggering a delay circuit in the DS199x. During write time slots, the delay circuit determines when the DS199x samples the data line. For a read data time slot, if a 0 is to be transmitted, the delay circuit determines how long the DS199x holds the data line low overriding the 1 generated by the master. If the data bit is a 1, the iButton leaves the read data time slot unchanged. Figure 11. READ/WRITE TIMING DIAGRAM Write-One Time Slot tSLOT VPULLUP VPULLUP MIN VIH MIN DS199x Sampling Window VIL MAX 0V tLOW1 15µs RESISTOR MASTER 60µs ≤ 60 µs tSLOT < 120 µs 1 µs ≤ t < 15 µs LOW1 1 µs ≤ tREC < ∞ 13 of 17 tREC DS1992/DS1993 Figure 11. READ/WRITE TIMING DIAGRAM (continued) Write-Zero Time Slot tREC tSLOT VPULLUP VPULLUP MIN VIH MIN DS199x Sampling Window VIL MAX 0V 15µs 60µs t LOW0 RESISTOR 60 µs ≤ tLOW0 < tSLOT < 120 µs MASTER 1 µs ≤ tREC < ∞ Read-Data Time Slot tREC tSLOT VPULLUP VPULLUP MIN VIH MIN Master Sampling Window VIL MAX 0V tSU tRELEASE tLOWR tRDV RESISTOR MASTER DS199x 60 µs ≤ tSLOT < 120 µs 1 µs ≤ tLOWR < 15 µs 0 ≤ tRELEASE < 45 µs 14 of 17 1 µs ≤ tREC < ∞ tRDV = 15 µs tSU < 1 µs DS1992/DS1993 PHYSICAL SPECIFICATIONS Size Weight Expected Service Life Safety See mechanical drawing 3.3 grams (F5 package) 10 years at +25°C Meets UL 913, 5th Ed., Rev. 1997-02-24; Intrinsically Safe Apparatus, Approved under Entity Concept for use in Class I, Division 1, Group A, B, C, and D Locations ABSOLUTE MAXIMUM RATINGS Voltage Range on any Pin Relative to Ground Operating Temperature Range Storage Temperature Range -0.5V to +7.0V -40°C to +70°C -40°C to +70°C This is a stress rating only and functional operation of the device at these or any other conditions above those indicated in the operation sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods of time may affect reliability. DC ELECTRICAL CHARACTERISTICS (TA = -40°C to +70°C) PARAMETER 1-Wire Pullup Voltage (Notes 1, 3) Logic 1 (Notes 1, 2) Logic 0 (Note 1) Output Logic Low at 4mA (Note 1) Input Load Current (Note 4) SYMBOL MIN VPUP 2.8 VIH VIL 2.2 -0.3 TYP VOL IL MAX UNITS 6.0 V +0.3 V V 0.4 V µA 5 CAPACITANCE (TA = +25°C) PARAMETER I/O (1-Wire) (Notes 5, 6) SYMBOL CIN/OUT MIN TYP 100 MAX 800 UNITS pF MIN TYP 60 1 60 exactly 15 0 15 MAX 120 15 120 UNITS µs µs µs µs µs µs µs µs µs µs µs AC ELECTRICAL CHARACTERISTICS (VPUP = 2.8V to 6.0V, TA = -40°C to +70°C) PARAMETER SYMBOL Time Slot tSLOT Write 1 Low Time tLOW1 Write 0 Low Time tLOW0 Read Data Valid tRDV Release Time tRELEASE Read Data Setup (Note 7) tSU Recovery Time tREC Reset Time High (Note 8) tRSTH Reset Time Low (Note 9) tRSTL Presence Detect High tPDH Presence Detect Low tPDL 1 480 480 15 60 15 of 17 45 1 960 60 240 DS1992/DS1993 Note 1: All voltages are referenced to ground. Note 2: VIH is a function of the external pullup resistor and the VCC power supply. Note 3: VPUP = external pullup voltage. Note 4: Input load is to ground. Note 5: Capacitance on the data line could be 800pF when power is first applied. If a 5kΩ resistor is used to pull up the data line to VPUP, 5µs after power has been applied, the parasite capacitance does not affect normal communications. Note 6: Guaranteed by design; not production tested. Note 7: Read data setup time refers to the time the host must pull the 1-Wire bus low to read a bit. Data is guaranteed to be valid within 1µs of this falling edge, and remains valid for 14µs minimum (15µs total from falling edge on 1-Wire bus). Note 8: An additional reset or communication sequence cannot begin until the reset high time has expired. Note 9: The reset low time (tRSTL) should be restricted to a maximum of 960µs, to allow interrupt signaling; otherwise, it could mask or conceal interrupt pulses. PACKAGE INFORMATION For the latest package outline information and land patterns (footprints), go to www.maxim-ic.com/packages. Note that a “+”, “#”, or “-” in the package code indicates RoHS status only. Package drawings may show a different suffix character, but the drawing pertains to the package regardless of RoHS status. PACKAGE TYPE F5 iButton PACKAGE CODE IB+5BW OUTLINE NO. 21-0266 16 of 17 LAND PATTERN NO. — DS1992/DS1993 REVISION HISTORY REVISION DATE 7/08 10/08 8/09 4/11 DESCRIPTION Updated the F5 MicroCan face brand with the latest per PCN H020201. Change the last sentence of the Parasite Power section to “The advantages of parasite power are two-fold: 1) by parasiting off this input, battery power is not consumed for 1-Wire ROM function commands, and 2) if the battery is exhausted for any reason, the ROM may still be read normally. The remaining circuitry of the DS1992 and DS1993 is solely operated by battery energy.” In the DC Electrical Characteristics section, relocated VPUP from the header to the EC table, changed VILMAX from 0.8V to 0.3V, and removed the VOH parameter for the 1-Wire pin. Updated the part numbers in the Ordering Information table to indicate a lead(Pb)-free/RoHS compliant product. Updated the UL certificate reference in the Common iButton Features and Physical Specifications sections; added the Package Information section. PAGES CHANGED 1 2 15 1 1, 15, 16 17 of 17 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. M a x i m I n t e g r a t e d P r o d u c t s , 1 2 0 S a n G a b r i e l D r iv e , S u n n y v a le , C A 9 4 0 8 6 4 0 8- 7 3 7 - 7 6 0 0 © 2011 Maxim Integrated Products Maxim is a registered trademark of Maxim Integrated Products, Inc.