Aluminum electrolytic capacitors Single-ended capacitors Series/Type: B41888 Date: December 2006 EPCOS AG 2007. Reproduction, publication and dissemination of this publication, enclosures hereto and the information contained therein without EPCOS' prior express consent is prohibited. Single-ended capacitors B41888 Extended useful life 105 °C Long-life grade capacitors Very low impedance Applications For use in switch-mode power supplies For professional industrial electronics, telecommunications and data processing equipment Automotive electronics Features Extended useful life Very low impedance at high frequency High ripple current capability Construction Radial leads Charge-discharge proof, polar Aluminum case with insulating sleeve Minus pole marking on the insulating sleeve Case with safety vent Delivery mode Terminal configurations and packing: Bulk Taped, Ammo pack Cut Kinked PAPR (protection against polarity reversal): crimped leads, J leads, bent leads Refer to chapter "Single-ended capacitors Taping, packing and lead configurations" for further details and ordering example. Please read Cautions and warnings and Important notes at the end of this document. Page 2 of 27 B41888 Extended useful life 105 °C Specifications and characteristics in brief Rated voltage VR Surge voltage VS Rated capacitance CR Capacitance tolerance 10 ... 63 V DC 1.15 VR 56 ... 12000 µF ±20% M Dissipation factor tan δ (20 °C, 120 Hz) For capacitance higher than 1000 µF add 0.02 for every increase of 1000 µF. Leakage current Ileak (20 °C, 5 min) Self-inductance ESL Useful life 105 °C, VR, IAC,R Requirements Voltage endurance test 105 °C, VR VR (V DC) tan δ (max.) 10 0.18 16 0.16 25 0.14 Diameter (mm) ≤12.5 16 18 ESL (nH) 20 26 34 35 0.12 50 0.10 63 0.09 > 5000 h for d = 8 mm > 7000 h for d = 10 mm > 10000 h for d ≥ 12.5 mm ∆C/C tan δ Ileak ≤ ±40% of initial value ≤ 3 times initial specified limit ≤ initial specified limit 5000 h for d = 8 mm 7000 h for d = 10 mm 10000 h for d ≥ 12.5 mm Post test requirements ∆C/C tan δ Ileak Vibration resistance test To IEC 60068-2-6, test Fc: Displacement amplitude 0.75 mm, frequency range 10 … 2000 Hz, acceleration max. 20 g, duration 3 × 2 h. Capacitor rigidly clamped by the aluminum case. IEC climatic category To IEC 60068-1: 55/105/56 (55 °C/+105 °C/56 days damp heat test) Sectional specification AEC-Q200, IEC 60384-4 Please read Cautions and warnings and Important notes at the end of this document. ≤ ±30% of initial value ≤ 2 times initial specified limit ≤ initial specified limit Page 3 of 27 B41888 Extended useful life 105 °C Dimensional drawings With stand-off rubber seal Diameters (mm): 8, 10, 12.5, 16, 18 With flat rubber seal Diameter (mm): 8 Dimensions and weights Dimensions (mm) d +0.5 8 10 10 10 12.5 12.5 12.5 16 16 16 18 18 18 18 18 l 11.5 +1.5 12.5 +1.0 16 +1.0 20 +2.0 20 +2.0 25 +2.0 40 +2.0 20 +2.0 25 +2.0 31.5 +2.0 20 +2.0 25 +2.0 31.5 +2.0 35 +2.0 40 +2.0 Please read Cautions and warnings and Important notes at the end of this document. a ±0.5 3.5 5.0 5.0 5.0 5.0 5.0 5.0 7.5 7.5 7.5 7.5 7.5 7.5 7.5 7.5 Page 4 of 27 b 0.60 ±0.05 0.60 ±0.05 0.60 ±0.05 0.60 ±0.05 0.60 ±0.05 0.60 ±0.05 0.80 ±0.05 0.80 ±0.05 0.80 ±0.05 0.80 ±0.05 0.80 ±0.1 0.80 ±0.1 0.80 ±0.1 0.80 ±0.1 0.80 ±0.1 Approx. weight g 1.0 1.6 1.9 2.6 3.6 4.5 7.4 5.5 7.5 7.8 8.0 9.0 11.0 13.0 16.0 B41888 Extended useful life 105 °C Overview of available types VR (V DC) 10 16 25 35 50 63 Case dimensions d × l (mm) CR (µF) 56 8 × 11.5 82 10 × 12.5 10 × 16 10 × 20 100 8 × 11.5 120 150 8 × 11.5 10 × 12.5 10 × 16 10 × 20 180 220 8 × 11.5 10 × 12.5 270 330 8 × 11.5 10 × 12.5 10 × 16 10 × 12.5 10 × 16 10 × 20 12.5 × 20 12.5 × 25 390 470 8 × 11.5 10 × 12.5 10 × 16 10 × 20 12.5 × 20 820 16 × 20 12.5 × 40 16 × 25 18 × 20 16 1000 10 × 16 1200 10 × 20 10 × 20 1800 12.5 × 20 2700 12.5 × 25 16 3300 12.5 × 25 3900 16 × 20 12.5 × 20 12.5 × 25 16 12.5 × 20 1500 2200 12.5 × 20 12.5 × 25 560 680 12.5 × 20 × 20 12.5 × 40 16 × 25 18 × 20 Please read Cautions and warnings and Important notes at the end of this document. × 20 16 18 × 31.5 × 25 18 × 31.5 12.5 × 25 16 × 20 12.5 × 40 16 × 25 18 × 20 18 × 20 16 18 × 31.5 × 25 18 × 35 12.5 × 40 16 × 25 18 × 31.5 18 × 40 × 31.5 × 25 18 × 35 18 × 31.5 18 × 40 Page 5 of 27 × 31.5 × 25 18 × 31.5 18 × 35 18 × 40 12.5 × 40 16 × 25 18 × 20 × 20 16 18 16 18 B41888 Extended useful life 105 °C VR (V DC) 10 16 25 35 50 63 Case dimensions d × l (mm) CR (µF) 4700 16 × 25 16 18 × 31.5 × 25 18 × 35 5600 12.5 × 40 16 × 25 18 × 20 18 × 31.5 18 × 40 6800 16 18 × 31.5 × 25 8200 18 × 31.5 18 × 35 10000 18 × 35 18 × 40 12000 18 × 40 Other voltage and capacitance ratings are available upon request. Technical data and ordering codes CR 120 Hz 20 °C µF Case dimensions d×l mm VR = 10 V DC 470 8 × 11.5 680 10 × 12.5 1000 10 × 16 1200 10 × 20 2200 12.5 × 20 3300 12.5 × 25 3900 16 × 20 4700 16 × 25 5600 12.5 × 40 5600 16 × 25 5600 18 × 20 6800 16 × 31.5 ESRmax 10 kHz 40 °C Ω ESRmax 120 Hz 20 °C Ω ESRmax 10 kHz 20 °C Ω Zmax 100 kHz 20 °C Ω IAC,R 100 kHz 105 °C mA IAC,max Ordering code 100 kHz (composition see 85 °C below) mA 1.630 0.930 0.516 0.403 0.307 0.237 0.233 0.190 0.149 0.190 0.226 0.154 0.484 0.334 0.227 0.189 0.115 0.084 0.071 0.065 0.059 0.059 0.059 0.052 0.204 0.116 0.064 0.050 0.038 0.030 0.029 0.024 0.019 0.024 0.028 0.019 0.183 0.101 0.059 0.046 0.035 0.027 0.026 0.022 0.017 0.022 0.025 0.017 690 900 1240 1500 2000 2459 2530 2930 3350 2930 3000 3600 966 1260 1736 2100 2800 3442 3542 4102 4690 4102 4200 5040 B41888C3477M*** B41888C3687M*** B41888C3108M*** B41888C3128M*** B41888C3228M*** B41888C3338M*** B41888C3398M*** B41888C3478M*** B41888C3568M*** B41888D3568M*** B41888E3568M*** B41888C3688M*** Composition of ordering code *** = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk (for ∅ ≥ 10 mm) 002 = for cut leads, bulk (for ∅ ≥ 10 mm) 003 = for crimped leads, blister (for ∅ ≥ 16 mm) 004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm) 008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm) 009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm) 012 = for bent 90° leads, blister (for ∅ 16 and 18 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 6 of 27 B41888 Extended useful life 105 °C Technical data and ordering codes CR 120 Hz 20 °C µF Case dimensions d×l mm VR = 10 V DC 6800 18 × 25 8200 18 × 31.5 10000 18 × 35 12000 18 × 40 VR = 16 V DC 330 8 × 11.5 470 10 × 12.5 680 10 × 16 1000 10 × 20 1500 12.5 × 20 2200 12.5 × 25 2700 16 × 20 3900 12.5 × 40 3900 16 × 25 3900 18 × 20 4700 16 × 31.5 4700 18 × 25 5600 18 × 31.5 8200 18 × 35 10000 18 × 40 VR = 25 V DC 220 8 × 11.5 330 10 × 12.5 470 10 × 16 680 10 × 20 1000 12.5 × 20 1500 12.5 × 25 1800 16 × 20 2200 18 × 20 ESRmax 10 kHz 40 °C Ω ESRmax 120 Hz 20 °C Ω ESRmax 10 kHz 20 °C Ω Zmax 100 kHz 20 °C Ω IAC,R 100 kHz 105 °C mA IAC,max Ordering code 100 kHz (composition see 85 °C below) mA 0.188 0.143 0.120 0.100 0.052 0.049 0.045 0.042 0.023 0.018 0.015 0.013 0.021 0.016 0.014 0.012 3396 4247 4300 5327 4755 5946 6020 7457 B41888D3688M*** B41888C3828M*** B41888C3109M*** B41888C3129M*** 1.630 0.930 0.516 0.403 0.307 0.237 0.233 0.149 0.190 0.226 0.154 0.188 0.143 0.120 0.100 0.612 0.430 0.297 0.202 0.135 0.103 0.084 0.065 0.065 0.065 0.059 0.059 0.054 0.043 0.040 0.204 0.116 0.064 0.050 0.038 0.030 0.029 0.019 0.024 0.028 0.019 0.023 0.018 0.015 0.013 0.183 0.101 0.059 0.046 0.035 0.027 0.026 0.017 0.022 0.025 0.017 0.021 0.016 0.014 0.012 690 900 1240 1500 2000 2459 2530 3350 2930 3000 3600 3200 4247 4300 5327 966 1260 1736 2100 2800 3442 3542 4690 4102 4200 5040 4480 5946 6020 7457 B41888C4337M*** B41888C4477M*** B41888C4687M*** B41888C4108M*** B41888C4158M*** B41888C4228M*** B41888C4278M*** B41888C4398M*** B41888D4398M*** B41888E4398M*** B41888C4478M*** B41888D4478M*** B41888C4568M*** B41888C4828M*** B41888C4109M*** 1.630 0.930 0.516 0.403 0.307 0.237 0.233 0.226 0.804 0.536 0.376 0.260 0.177 0.118 0.098 0.090 0.204 0.116 0.064 0.050 0.038 0.030 0.029 0.028 0.183 0.101 0.059 0.046 0.035 0.027 0.026 0.025 690 900 1240 1500 2000 2459 2530 3000 966 1260 1736 2100 2800 3442 3542 4200 B41888C5227M*** B41888C5337M*** B41888C5477M*** B41888C5687M*** B41888C5108M*** B41888C5158M*** B41888C5188M*** B41888C5228M*** Composition of ordering code *** = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk (for ∅ ≥ 10 mm) 002 = for cut leads, bulk (for ∅ ≥ 10 mm) 003 = for crimped leads, blister (for ∅ ≥ 16 mm) 004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm) 008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm) 009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm) 012 = for bent 90° leads, blister (for ∅ 16 and 18 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 7 of 27 B41888 Extended useful life 105 °C Technical data and ordering codes CR 120 Hz 20 °C µF Case dimensions d×l mm VR = 25 V DC 2700 12.5 × 40 2700 16 × 25 3300 16 × 31.5 3300 18 × 25 3900 18 × 31.5 4700 18 × 35 5600 18 × 40 VR = 35 V DC 150 8 × 11.5 220 10 × 12.5 330 10 × 16 470 10 × 20 680 12.5 × 20 1000 12.5 × 25 1200 16 × 20 1800 12.5 × 40 1800 16 × 25 1800 18 × 20 2200 16 × 31.5 2200 18 × 25 2700 18 × 31.5 3300 18 × 35 3900 18 × 40 VR = 50 V DC 100 8 × 11.5 150 10 × 12.5 220 10 × 16 270 10 × 20 470 12.5 × 20 ESRmax 10 kHz 40 °C Ω ESRmax 120 Hz 20 °C Ω ESRmax 10 kHz 20 °C Ω Zmax 100 kHz 20 °C Ω IAC,R 100 kHz 105 °C mA IAC,max Ordering code 100 kHz (composition see 85 °C below) mA 0.149 0.190 0.154 0.188 0.143 0.120 0.100 0.075 0.075 0.069 0.069 0.058 0.054 0.050 0.019 0.024 0.019 0.023 0.018 0.015 0.013 0.017 0.022 0.017 0.021 0.016 0.014 0.012 3350 2930 3600 3200 4247 4300 5327 4690 4102 5040 4480 5946 6020 7457 B41888C5278M*** B41888D5278M*** B41888C5338M*** B41888D5338M*** B41888C5398M*** B41888C5478M*** B41888C5568M*** 1.630 0.930 0.516 0.403 0.307 0.237 0.233 0.149 0.190 0.226 0.154 0.188 0.143 0.120 0.100 1.011 0.689 0.459 0.323 0.223 0.152 0.126 0.084 0.084 0.084 0.080 0.080 0.065 0.060 0.052 0.204 0.116 0.064 0.050 0.038 0.030 0.029 0.019 0.024 0.028 0.019 0.023 0.018 0.015 0.013 0.183 0.101 0.059 0.046 0.035 0.027 0.026 0.017 0.022 0.025 0.017 0.021 0.016 0.014 0.012 690 900 1240 1500 2000 2459 2530 3350 2930 3000 3600 3200 4247 4300 5327 966 1260 1736 2100 2800 3442 3542 4690 4102 4200 5040 4480 5946 6020 7457 B41888C7157M*** B41888C7227M*** B41888C7337M*** B41888C7477M*** B41888C7687M*** B41888C7108M*** B41888C7128M*** B41888C7188M*** B41888D7188M*** B41888E7188M*** B41888C7228M*** B41888D7228M*** B41888C7278M*** B41888C7338M*** B41888C7398M*** 4.920 1.820 1.030 0.672 0.518 1.263 0.842 0.574 0.468 0.269 0.615 0.228 0.129 0.084 0.065 0.540 0.203 0.115 0.075 0.060 500 600 1050 1180 1800 700 840 1470 1652 2520 B41888C6107M*** B41888C6157M*** B41888C6227M*** B41888C6277M*** B41888C6477M*** Composition of ordering code *** = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk (for ∅ ≥ 10 mm) 002 = for cut leads, bulk (for ∅ ≥ 10 mm) 003 = for crimped leads, blister (for ∅ ≥ 16 mm) 004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm) 008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm) 009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm) 012 = for bent 90° leads, blister (for ∅ 16 and 18 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 8 of 27 B41888 Extended useful life 105 °C Technical data and ordering codes CR 120 Hz 20 °C µF Case dimensions d×l mm VR = 50 V DC 560 12.5 × 25 820 16 × 20 1000 12.5 × 40 1000 16 × 25 1000 18 × 20 1200 16 × 31.5 1200 18 × 25 1800 18 × 31.5 2200 18 × 35 2700 18 × 40 VR = 63 V DC 56 8 × 11.5 82 10 × 12.5 120 10 × 16 180 10 × 20 270 12.5 × 20 330 12.5 × 20 390 12.5 × 25 470 16 × 20 680 12.5 × 40 680 16 × 25 680 18 × 20 820 16 × 31.5 820 18 × 25 1200 18 × 31.5 1500 18 × 35 1800 18 × 40 ESRmax 10 kHz 40 °C Ω ESRmax 120 Hz 20 °C Ω ESRmax 10 kHz 20 °C Ω Zmax 100 kHz 20 °C Ω IAC,R 100 kHz 105 °C mA IAC,max Ordering code 100 kHz (composition see 85 °C below) mA 0.344 0.410 0.216 0.283 0.283 0.221 0.275 0.204 0.177 0.159 0.226 0.154 0.126 0.126 0.126 0.105 0.105 0.070 0.069 0.056 0.043 0.051 0.027 0.035 0.035 0.028 0.034 0.025 0.022 0.020 0.040 0.046 0.025 0.032 0.032 0.025 0.031 0.023 0.020 0.018 2024 1957 2920 2700 2541 3010 2795 3542 3800 4000 2834 2740 4088 3780 3558 4214 3914 4959 5320 5600 B41888C6567M*** B41888C6827M*** B41888C6108M*** B41888D6108M*** B41888E6108M*** B41888C6128M*** B41888D6128M*** B41888C6188M*** B41888C6228M*** B41888C6278M*** 5.413 5.766 3.075 1.986 1.688 1.688 1.236 1.037 0.717 0.772 0.960 0.541 0.761 0.518 0.441 0.375 2.030 1.386 0.947 0.632 0.421 0.344 0.291 0.242 0.167 0.167 0.167 0.139 0.139 0.095 0.076 0.063 0.541 0.577 0.308 0.199 0.169 0.169 0.124 0.104 0.072 0.077 0.096 0.054 0.076 0.052 0.044 0.038 0.488 0.500 0.279 0.180 0.153 0.153 0.112 0.094 0.065 0.070 0.087 0.049 0.069 0.047 0.040 0.034 283 323 474 644 800 800 1020 1161 1629 1460 1302 1910 1584 2094 2366 2708 396 453 664 901 1120 1120 1428 1625 2281 2045 1823 2674 2217 2932 3313 3792 B41888C8566M*** B41888C8826M*** B41888C8127M*** B41888C8187M*** B41888C8277M*** B41888C8337M*** B41888C8397M*** B41888C8477M*** B41888C8687M*** B41888D8687M*** B41888E8687M*** B41888C8827M*** B41888D8827M*** B41888C8128M*** B41888C8158M*** B41888C8188M*** Composition of ordering code *** = Version 000 = for standard leads, bulk 001 = for kinked leads, bulk (for ∅ ≥ 10 mm) 002 = for cut leads, bulk (for ∅ ≥ 10 mm) 003 = for crimped leads, blister (for ∅ ≥ 16 mm) 004 = for J leads, blister (from d × l = 10 × 12.5 mm to 18 × 35 mm) 008 = for taped leads, Ammo pack, lead spacing F = 5.0 mm (from d × l = 8 × 11.5 mm to 12.5 × 25 mm) 009 = for taped leads, Ammo pack, lead spacing F = 7.5 mm (from d × l = 16 × 20 mm to 18 × 31.5 mm) 012 = for bent 90° leads, blister (for ∅ 16 and 18 mm) Please read Cautions and warnings and Important notes at the end of this document. Page 9 of 27 B41888 Extended useful life 105 °C Useful life depending on ambient temperature TA under ripple current operating conditions1) d = 8 mm d = 10 mm 1) Refer to chapter "General technical information, 5.3 Calculation of useful life" for an explanation on how to interpret the useful life graphs. Please read Cautions and warnings and Important notes at the end of this document. Page 10 of 27 B41888 Extended useful life 105 °C Useful life depending on ambient temperature TA under ripple current operating conditions2) d = ≥ 12.5 mm Frequency factor of permissible ripple current IAC versus frequency f 2) Refer to chapter "General technical information, 5.3 Calculation of useful life" for an explanation on how to interpret the useful life graphs. Please read Cautions and warnings and Important notes at the end of this document. Page 11 of 27 B41888 Extended useful life 105 °C Taping, packing and lead configurations Taping Single-ended capacitors are available taped in Ammo pack from diameter 5 to 18 mm as follows: Lead spacing F = 2.5 mm (∅ d = 5 … 6.3 mm) Lead spacing F = 3.5 mm (∅ d = 8 mm) Lead spacing F = 5.0 mm (∅ d = 5 … 12.5 mm) Lead spacing F = 7.5 mm (∅ d = 16 ... 18 mm). Lead spacing 2.5 mm (∅ d = 5 ... 6.3 mm) Last 3 digits of ordering code: 007 Dimensions in mm ∅d 5 F H W W0 W1 W2 H0 P P0 P1 I1 t ∆h D0 2.5 18.5 18.0 5.5 9.0 1.5 16.0 12.7 12.7 5.1 1.0 0.7 1.0 4.0 6.3 Toler- +0.8 ±0.75 ±0.5 min. ±0.5 max. ±0.5 ±1.0 ±0.2 ±0.5 max. ±0.2 max. ±0.2 ance 02 Please read Cautions and warnings and Important notes at the end of this document. Page 12 of 27 B41888 Extended useful life 105 °C Lead spacing 3.5 mm (∅ d = 8 mm) Last 3 digits of ordering code: 006 Dimensions in mm ∅d 8 Tolerance F H W W0 W1 W2 P P0 P1 I1 t ∆h 3.5 18.5 18.0 12.5 9.0 1.5 12.7 12.7 4.6 1.0 0.7 1.0 +0.8 02 1.0 ±0.5 min. ±0.5 max. ±1.0 ±0.2 ±0.5 max. ±0.2 Please read Cautions and warnings and Important notes at the end of this document. Page 13 of 27 D0 4.0 max. ±0.2 B41888 Extended useful life 105 °C Lead spacing 5.0 mm (∅ d = 5 ... 8 mm) Last 3 digits of ordering code: 008 Lead spacing 5.0 mm (∅ d = 10 ... 12.5 mm) Last 3 digits of ordering code: 008 Dimensions in mm ∅d 5 6.3 F H W W0 W1 W2 H0 P P0 P1 I1 t ∆h D0 5.0 18.5 18.0 5.5 9.0 1.5 16.0 12.7 12.7 3.85 1.0 0.7 1.0 4.0 16.0 12.7 12.7 3.85 18.0 12.5 9.0 1.5 12.7 12.7 3.85 1.0 0.7 1.0 4.0 15.0 15.0 5.0 ±1.0 ±0.2 ±0.5 8 10 20.0 5.0 12.5 Toler- +0.8 ance 02 19.0 19.0 ±0.75 ±0.5 min. ±0.5 max. ±0.5 Please read Cautions and warnings and Important notes at the end of this document. Page 14 of 27 max. ±0.2 max. ±0.2 B41888 Extended useful life 105 °C Lead spacing 7.5 mm (∅ d = 16 ...18 mm) Last 3 digits of ordering code: 009 Dimensions in mm ∅d 16 F H W 7.5 18.5 18.0 18 *) Toler0.5 ±0.8 ±0.5 ance +0.75 W0 W1 W2 P P0 P1 I1 t ∆P ∆h D0 12.5 9.0 1.5 30.0 15.0 3.75 1.0 0.7 0 0 4.0 min. ±0.5 max. ±1.0 ±0.2 ±0.5 max. ±0.2 ±1.0 ±1.0 ±0.2 *) Available only for case dimensions 18 × 20, 18 × 25 and 18 × 31.5 mm Please read Cautions and warnings and Important notes at the end of this document. Page 15 of 27 B41888 Extended useful life 105 °C Packing units and box dimensions Ammo pack Please read Cautions and warnings and Important notes at the end of this document. Case size d×l mm Dimensions (mm) Amax Bmax Cmax 5 × 11 345 55 240 2000 6.3 × 11 345 55 290 2000 8 × 11.5 345 55 240 1000 10 × 12.5 345 55 280 750 10 × 16 345 60 200 500 10 × 20 345 60 200 500 12.5 × 20 345 65 280 500 12.5 × 25 345 65 280 500 12.5 × 25 345 65 280 500 12.5 × 30 345 65 275 500 16 × 20 315 65 275 300 16 × 25 315 65 275 300 16 × 31.5 315 65 275 300 18 × 20 315 65 275 250 18 × 25 315 65 275 250 18 × 31.5 315 65 275 250 Page 16 of 27 Packing units pcs. B41888 Extended useful life 105 °C Kinked or cut leads Single-ended capacitors are available with kinked or cut leads. Other lead configurations also available upon request. Kinked leads Last 3 digits of ordering code: 001 With stand-off rubber seal Case size d × l (mm) With flat rubber seal Please read Cautions and warnings and Important notes at the end of this document. Page 17 of 27 Dimensions (mm) a ±0.5 10 × 20 5.0 12.5 × 20 5.0 12.5 × 25 5.0 12.5 × 30 5.0 12.5 × 35 5.0 12.5 × 40 5.0 16 × 20 7.5 16 × 25 7.5 16 × 31.5 7.5 18 × 20 7.5 18 × 25 7.5 18 × 31.5 7.5 18 × 35 7.5 18 × 40 7.5 20 × 20 10.0 20 × 25 10.0 20 × 40 10.0 22 × 30 10.0 22 × 35 10.0 22 × 40 10.0 B41888 Extended useful life 105 °C Cut leads Last 3 digits of ordering code: 002 With stand-off rubber seal Case size d × l (mm) With flat rubber seal Please read Cautions and warnings and Important notes at the end of this document. Page 18 of 27 Dimensions (mm) a ±0.5 10 × 12.5 5.0 10 × 16 5.0 10 × 20 5.0 12.5 × 20 5.0 12.5 × 25 5.0 12.5 × 30 5.0 12.5 × 35 5.0 12.5 × 40 5.0 16 × 20 7.5 16 × 25 7.5 16 × 31.5 7.5 18 × 20 7.5 18 × 25 7.5 18 × 31.5 7.5 18 × 35 7.5 18 × 40 7.5 20 × 20 10.0 20 × 25 10.0 20 × 40 10.0 B41888 Extended useful life 105 °C PAPR leads (Protection Against Polarity Reversal) These lead configurations ensure correct placement of the capacitor on the PCB with regard to polarity. PAPR leads are available for diameters from 10 mm up to 20 mm. There are three configurations available: Crimped leads, J leads, bent 90° leads Crimped leads Last 3 digits of ordering code: 003 With stand-off rubber seal With flat rubber seal Suggestion for PCB hole diameter Case size d × l (mm) Dimensions (mm) B ±0.2 C ±0.5 D ±0.1 E ±0.1 16 × 20 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05 16 × 25 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05 16 × 31.5 1.5 3.0 1.3 0.3 7.5 0.8 ±0.05 18 × 20 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1 18 × 25 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1 18 × 31.5 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1 18 × 35 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1 18 × 40 1.5 3.0 1.3 0.3 7.5 0.8 ±0.1 20 × 20 1.5 3.0 1.6 0.3 10.0 1.0 ±0.1 20 × 25 1.5 3.0 1.6 0.3 10.0 1.0 ±0.1 20 × 40 1.5 3.0 1.6 0.3 10.0 1.0 ±0.1 Please read Cautions and warnings and Important notes at the end of this document. Page 19 of 27 a ±0.5 ∅b B41888 Extended useful life 105 °C J leads Last 3 digits of ordering code: 004 Suggestion for PCB hole diameter Case size d × l (mm) Dimensions (mm) C ±0.5 E ±0.5 J ±0.2 10 × 12.5 3.2 0.7 1.2 5.0 0.6 ±0.05 10 × 16 3.2 0.7 1.2 5.0 0.6 ±0.05 10 × 20 3.2 0.7 1.2 5.0 0.6 ±0.05 12.5 × 20 3.2 0.7 1.2 5.0 0.6 ±0.05 12.5 × 25 3.2 0.7 1.2 5.0 0.6 ±0.05 16 × 20 3.5 0.7 1.6 7.5 0.8 ±0.05 16 × 25 3.5 0.7 1.6 7.5 0.8 ±0.05 16 × 31.5 3.5 0.7 1.6 7.5 0.8 ±0.05 18 × 20 3.5 0.7 1.6 7.5 0.8 ±0.1 18 × 25 3.5 0.7 1.6 7.5 0.8 ±0.1 18 × 31.5 3.5 0.7 1.6 7.5 0.8 ±0.1 18 × 35 3.5 0.7 1.6 7.5 0.8 ±0.1 Please read Cautions and warnings and Important notes at the end of this document. Page 20 of 27 a ±0.5 ∅b B41888 Extended useful life 105 °C Bent 90° leads for horizontal mounting pinning Last 3 digits of ordering code: 012 Case size d × l (mm) Dimensions (mm) C ±0.5 E ±0.5 F ±0.5 a ±0.5 ∅b 16 × 20 4.0 4.0 12.0 7.5 0.8 ±0.05 16 × 25 4.0 4.0 12.0 7.5 0.8 ±0.05 16 × 31.5 4.0 4.0 12.0 7.5 0.8 ±0.05 18 × 20 4.0 4.0 13.0 7.5 0.8 ±0.1 18 × 25 4.0 4.0 13.0 7.5 0.8 ±0.1 18 × 31.5 4.0 4.0 13.0 7.5 0.8 ±0.1 18 × 35 4.0 4.0 13.0 7.5 0.8 ±0.1 18 × 40 4.0 4.0 13.0 7.5 0.8 ±0.1 Bent leads for diameter 12.5 mm available upon request. Please read Cautions and warnings and Important notes at the end of this document. Page 21 of 27 B41888 Extended useful life 105 °C Overview of packing units and code numbers for case sizes 5 × 11 ... 16 × 31.5 PAPR Case size d×l Taped, Ammo pack mm Standard, bulk pcs. 5 × 11 2000 6.3 × 11 2500 2000 8 × 11.5 1000 1000 10 × 12.5 1000 750 10 × 16 100 500 1000 10 × 20 500 500 500 500 12.5 × 20 350 500 350 350 12.5 × 25 250 500 500 500 12.5 × 30 200 500 175 175 12.5 × 35 175 - 175 175 12.5 × 40 175 - 175 175 16 × 20 250 300 200 200 16 × 25 250 300 200 16 × 31.5 200 300 The last three digits of the complete ordering code state the lead configuration 000 Code 006 007 008 009 1) pcs. Kinked leads, bulk pcs. Cut Crimped J leads leads, leads bulk pcs. pcs. pcs. 2000 F (mm) d (mm) 3.5 2.5 5 7.5 1000 675 675 500 300 1) 225 1) 180 1) 150 1) 150 1) 200 200 120 200 200 200 120 250 250 344 344 120 001 002 003 004 012 8 5...6.3 5...12.5 16...18 Available upon request Please read Cautions and warnings and Important notes at the end of this document. Bent 90° leads, blister pcs. Page 22 of 27 B41888 Extended useful life 105 °C Overview of packing units and code numbers for case sizes 18 × 20 ... 25 × 40 PAPR Case size d×l Taped, Ammo pack mm Standard, bulk pcs. pcs. Kinked leads, bulk pcs. Cut Crimped J leads leads, leads bulk pcs. pcs. pcs. Bent 90° leads, blister pcs. 18 × 20 175 18 × 25 150 250 175 175 200 200 120 250 150 150 200 200 18 × 31.5 120 100 250 100 100 150 150 120 18 × 35 100 100 100 150 150 150 18 × 40 125 100 100 120 72 20 × 20 125 125 125 200 20 × 25 125 125 125 200 20 × 30 100 100 100 120 20 × 35 100 100 100 120 20 × 40 100 100 100 120 22 × 30 80 100 100 22 × 35 80 100 100 22 × 40 80 100 100 25 × 40 40 100 The last three digits of the complete ordering code state the lead configuration 000 Code 007 008 009 001 002 Please read Cautions and warnings and Important notes at the end of this document. F (mm) d (mm) 2.5 5 7.5 4...6.3 6.3...12.5 16...18 Page 23 of 27 003 004 012 B41888 Extended useful life 105 °C Cautions and warnings Personal safety The electrolytes used by EPCOS have not only been optimized with a view to the intended application, but also with regard to health and environmental compatibility. They do not contain any solvents that are detrimental to health, e.g. dimethyl formamide (DMF) or dimethyl acetamide (DMAC). Furthermore, part of the high-voltage electrolytes used by EPCOS are self-extinguishing. They contain flame-retarding substances which will quickly extinguish any flame that may have been ignited. As far as possible, EPCOS does not use any dangerous chemicals or compounds to produce operating electrolytes. However, in exceptional cases, such materials must be used in order to achieve specific physical and electrical properties because no safe substitute materials are currently known. However, the amount of dangerous materials used in our products has been limited to an absolute minimum. Nevertheless, the following rules should be observed when handling Al electrolytic capacitors: Any escaping electrolyte should not come into contact with eyes or skin. If electrolyte does come into contact with the skin, wash the affected parts immediately with running water. If the eyes are affected, rinse them for 10 minutes with plenty of water. If symptoms persist, seek medical treatment. Avoid breathing in electrolyte vapor or mists. Workplaces and other affected areas should be well ventilated. Clothing that has been contaminated by electrolyte must be changed and rinsed in water. Please read Cautions and warnings and Important notes at the end of this document. Page 24 of 27 B41888 Extended useful life 105 °C Product safety The table below summarize the safety instructions that must be observed without fail. A detailed description can be found in the relevant sections of chapter "General technical information". Topic Safety information Polarity Make sure that polar capacitors are connected with the right polarity. Reverse voltage Voltages polarity classes should be prevented by connecting a diode. Do not exceed the upper category temperatur. Upper category temperature Maintenance Mounting position of screw terminal capacitors Mounting of single-ended capacitors Robustness of terminals Soldering Make periodic inspections of the capacitors. Before the inspection, make sure that the power supply is turned off and carefully discharge the electricity of the capacitors. Do not apply any mechanical stress to the capacitor terminals. Do not mount the capacitor with the terminals (safety vent) upside down. Reference Chapter "General technical information" 1 "Basic construction of aluminum electrolytic capacitors" 3.1.6 "Reverse voltage" 7.2 "Maximum permissible operating temperature" 10 "Maintenance" 11.1. "Mounting positions of capacitors with screw terminals" The internal structure of single-ended capacitors 11.4 might be damaged if excessive force is applied to "Mounting the lead wires. considerations for Avoid any compressive, tensile or flexural stress. single-ended capacitors" Do not move the capacitor after soldering to PC board. Do not pick up the PC board by the soldered capacitor. Do not insert the capacitor on the PC board with a hole space different to the lead space specified. The following maximum tightening torques must 11.3 not be exceeded when connecting screw "Mounting torques" terminals: M5: 2 Nm M6: 2.5 Nm Do not exceed the specified time or temperature 11.5 limits during soldering. "Soldering" Please read Cautions and warnings and Important notes at the end of this document. Page 25 of 27 B41888 Extended useful life 105 °C Topic Soldering, cleaning agents Passive flammability Active flammability Safety information Reference Chapter "General technical information" Do not allow halogenated hydrocarbons to come 11.6 into contact with aluminum electrolytic capacitors. "Cleaning agents" Avoid external energy, such as fire or electricity. 8.1 "Passive flammability" Avoid overload of the capacitors. 8.2 "Active flammability" Breakdown strength Do not damage the insulating sleeve, especially of insulating when ring clips are used for mounting. sleeves Please read Cautions and warnings and Important notes at the end of this document. Page 26 of 27 Reference Chapter "Capacitors with screw terminals" "Screw terminals accessories" Important notes The following applies to all products named in this publication: 1. Some parts of this publication contain statements about the suitability of our products for certain areas of application. These statements are based on our knowledge of typical requirements that are often placed on our products in the areas of application concerned. We nevertheless expressly point out that such statements cannot be regarded as binding statements about the suitability of our products for a particular customer application. As a rule, EPCOS is either unfamiliar with individual customer applications or less familiar with them than the customers themselves. For these reasons, it is always ultimately incumbent on the customer to check and decide whether an EPCOS product with the properties described in the product specification is suitable for use in a particular customer application. 2. We also point out that in individual cases, a malfunction of passive electronic components or failure before the end of their usual service life cannot be completely ruled out in the current state of the art, even if they are operated as specified. In customer applications requiring a very high level of operational safety and especially in customer applications in which the malfunction or failure of a passive electronic component could endanger human life or health (e.g. in accident prevention or life-saving systems), it must therefore be ensured by means of suitable design of the customer application or other action taken by the customer (e.g. installation of protective circuitry or redundancy) that no injury or damage is sustained by third parties in the event of malfunction or failure of a passive electronic component. 3. The warnings, cautions and product-specific notes must be observed. 4. In order to satisfy certain technical requirements, some of the products described in this publication may contain substances subject to restrictions in certain jurisdictions (e.g. because they are classed as “hazardous”). Useful information on this will be found in our Material Data Sheets on the Internet (www.epcos.com/material). Should you have any more detailed questions, please contact our sales offices. 5. We constantly strive to improve our products. Consequently, the products described in this publication may change from time to time. The same is true of the corresponding product specifications. Please check therefore to what extent product descriptions and specifications contained in this publication are still applicable before or when you place an order. We also reserve the right to discontinue production and delivery of products. Consequently, we cannot guarantee that all products named in this publication will always be available. 6. Unless otherwise agreed in individual contracts, all orders are subject to the current version of the “General Terms of Delivery for Products and Services in the Electrical Industry” published by the German Electrical and Electronics Industry Association (ZVEI). 7. The trade names EPCOS, EPCOS-JONES, BAOKE, Alu-X, CeraDiode, CSSP, MLSC, PhaseCap, PhaseMod, SIFERRIT, SIFI, SIKOREL, SilverCap, SIMID, SIOV, SIP5D, SIP5K, UltraCap, WindCap are trademarks registered or pending in Europe and in other countries. Further information will be found on the Internet at www.epcos.com/trademarks. Page 27 of 27