Cirrus CS42426-CQZ 114 db, 192khz 6-ch codec with pll Datasheet

CS42426
114 dB, 192 kHz 6-Ch Codec with PLL
Features
General Description
Six 24-bit D/A, two 24-bit A/D converters
114 dB DAC / 114 dB ADC dynamic range
-100 dB THD+N
System sampling rates up to 192 kHz
Integrated low-jitter PLL for increased system
jitter tolerance
PLL clock or OMCK system clock selection
7 configurable general purpose outputs
ADC high pass filter for DC offset calibration
Expandable ADC channels and one-line
mode support
Digital output volume control with soft ramp
Digital +/-15 dB input gain adjust for ADC
Differential analog architecture
Supports logic levels between 5 V and 1.8 V
VA AGND
GPO1
GPO2
GPO3
GPO4
GPO5
GPO6
GPO7
The CS42426 CODEC provides two analog-to-digital and six
digital-to-analog Delta-Sigma converters, as well as an integrated PLL, in a 64-pin LQFP package.
The CS42426 integrated PLL provides a low-jitter system
clock. The internal stereo ADC is capable of independent channel gain control for single-ended or differential analog inputs.
All six channels of DAC provide digital volume control and differential analog outputs. The general purpose outputs may be
driven high or low, or mapped to a variety of DAC mute controls
or ADC overflow indicators.
The CS42426 is ideal for audio systems requiring wide
dynamic range, negligible distortion and low noise, such as A/V
receivers, DVD receivers, digital speaker and automotive audio
systems.
ORDERING INFORMATION
CS42426-CQZ -10° to 70° C
CS42426-DQZ -40° to 85° C
CDB42428
Evaluation Board
REFGND VQ FILT+
OMCK
RMCK
LPFLT
VLC
64-pin LQFP
64-pin LQFP
DGND VD
INT
Mult/Div
RST
AD0/CS
AD1/CDIN
SDA/CDOUT
SCL/CCLK
Control
Port
GPO
Internal Voltage
Reference
Mute
PLL
AINL+
AINL-
ADC#1
Digital Filter
Gain & Clip
AINR+
AINR-
ADC#2
Digital Filter
Gain & Clip
AOUTB2+
AOUTB2-
DAC#3
DAC#4
AOUTA3+
AOUTA3-
DAC#5
AOUTB3+
AOUTB3-
DAC#6
Level Translator
AOUTA2+
AOUTA2-
DAC Serial Audio Port
DAC#2
Volume Control
AOUTB1+
AOUTB1-
ADC
Serial
Audio
Port
ADCIN1
ADCIN2
ADC_SDOUT
ADC_LRCK
ADC_SCLK
VLS
Digital Filter
DAC#1
Analog Filter
AOUTA1+
AOUTA1-
Level Translator
MUTEC
DAC_LRCK
DAC_SCLK
DAC_SDIN1
DAC_SDIN2
DAC_SDIN3
Advance Product Information
This document contains information for a new product.
Cirrus Logic reserves the right to modify this product without notice.
Cirrus Logic, Inc.
www.cirrus.com
Copyright © Cirrus Logic, Inc. 2004
(All Rights Reserved)
JUL ‘04
DS604A2
1
CS42426
TABLE OF CONTENTS
1 PIN DESCRIPTIONS ................................................................................................................. 6
2 TYPICAL CONNECTION DIAGRAMS ..................................................................................... 8
3 APPLICATIONS ....................................................................................................................... 10
3.1 Overview .......................................................................................................................... 10
3.2 Analog Inputs ................................................................................................................... 10
3.2.1 Line Level Inputs ................................................................................................. 10
3.2.2 External Input Filter ............................................................................................. 11
3.2.3 High Pass Filter and DC Offset Calibration ......................................................... 11
3.3 Analog Outputs ................................................................................................................ 11
3.3.1 Line Level Outputs and Filtering ......................................................................... 11
3.3.2 Interpolation Filter ............................................................................................... 12
3.3.3 Digital Volume and Mute Control ........................................................................ 12
3.3.4 ATAPI Specification ............................................................................................ 13
3.4 Clock Generation ............................................................................................................. 14
3.4.1 PLL and Jitter Attenuation ................................................................................... 14
3.4.2 OMCK System Clock Mode ................................................................................ 15
3.4.3 Master Mode ....................................................................................................... 15
3.4.4 Slave Mode ......................................................................................................... 15
3.5 Digital Interfaces .............................................................................................................. 16
3.5.1 Serial Audio Interface Signals ............................................................................. 16
3.5.2 Serial Audio Interface Formats ............................................................................ 18
3.5.3 ADCIN1/ADCIN2 Serial Data Format .................................................................. 21
3.5.4 One Line Mode(OLM) Configurations ................................................................. 22
3.6 Control Port Description and Timing ................................................................................ 26
Contacting Cirrus Logic Support
For all product questions and inquiries contact a Cirrus Logic Sales Representative.
To find one nearest you go to www.cirrus.com/
IMPORTANT NOTICE
"Advance" product information describes products that are in development and subject to development changes. Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject to change without
notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale supplied at the time of order acknowledgment, including those pertaining to warranty, patent infringement, and limitation of liability. No
responsibility is assumed by Cirrus for the use of this information, including use of this information as the basis for manufacture or sale of any items,
or for infringement of patents or other rights of third parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants
no license, express or implied under any patents, mask work rights, copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus
owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within
your organization with respect to Cirrus integrated circuits or other parts of Cirrus. This consent does not extend to other copying such as copying
for general distribution, advertising or promotional purposes, or for creating any work for resale.
An export permit needs to be obtained from the competent authorities of the Japanese Government if any of the products or technologies described
in this material and controlled under the "Foreign Exchange and Foreign Trade Law" is to be exported or taken out of Japan. An export license and/or
quota needs to be obtained from the competent authorities of the Chinese Government if any of the products or technologies described in this material
is subject to the PRC Foreign Trade Law and is to be exported or taken out of the PRC.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR
SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE IN AIRCRAFT SYSTEMS, MILITARY APPLICATIONS, PRODUCTS SURGICALLY IMPLANTED INTO THE
BODY, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS (INCLUDING MEDICAL DEVICES, AIRCRAFT SYSTEMS OR COMPONENTS AND PERSONAL OR AUTOMOTIVE SAFETY OR SECURITY DEVICES). INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS,
STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE,
WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER'S CUSTOMER USES
OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY
CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING
ATTORNEYS' FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES.
Purchase of I2C components of Cirrus Logic, Inc., or one of its sublicensed Associated Companies conveys a license under the Phillips I2C Patent Rights to use
those components in a standard I2C system.
Cirrus Logic, Cirrus, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may
be trademarks or service marks of their respective owners.
2
CS42426
4
5
6
7
8
9
3.6.1 SPI Mode ............................................................................................................ 26
3.6.2 I2C Mode ............................................................................................................ 27
3.7 Interrupts ......................................................................................................................... 28
3.8 Reset and Power-up ....................................................................................................... 29
3.9 Power Supply, Grounding, and PCB layout ..................................................................... 29
REGISTER QUICK REFERENCE ........................................................................................... 30
REGISTER DESCRIPTION ..................................................................................................... 32
5.1 Memory Address Pointer (MAP) ....................................................................................... 32
5.2 Chip I.D. and Revision Register (address 01h) (Read Only) ............................................ 32
5.3 Power Control (address 02h)............................................................................................ 33
5.4 Functional Mode (address 03h) ........................................................................................ 33
5.5 Interface Formats (address 04h) ...................................................................................... 34
5.6 Misc Control (address 05h) .............................................................................................. 36
5.7 Clock Control (address 06h) ............................................................................................. 37
5.8 OMCK/PLL_CLK Ratio (address 07h) (Read Only) ......................................................... 39
5.9 Clock Status (address 08h) (Read Only) .......................................................................... 39
5.10 Volume Control (address 0Dh) ....................................................................................... 40
5.11 Channel Mute (address 0Eh).......................................................................................... 41
5.12 Volume Control (addresses 0Fh, 10h, 11h, 12h, 13h, 14h) ........................................ 42
5.13 Channel Invert (address 17h) ......................................................................................... 42
5.14 Mixing Control Pair 1 (Channels A1 & B1)(address 18h)
Mixing Control Pair 2 (Channels A2 & B2)(address 19h)
Mixing Control Pair 3 (Channels A3 & B3)(address 1Ah) ............................................. 42
5.15 ADC Left Channel Gain (address 1Ch) .......................................................................... 45
5.16 ADC Right Channel Gain (address 1Dh) ........................................................................ 45
5.17 Interrupt Control (address 1Eh) ...................................................................................... 45
5.18 Interrupt Status (address 20h) (Read Only) ................................................................... 46
5.19 Interrupt Mask (address 21h) ......................................................................................... 47
5.20 Interrupt Mode MSB (address 22h)
Interrupt Mode LSB (address 23h)................................................................................ 47
5.21 MuteC Pin Control (address 28h) ................................................................................... 47
5.22 General Purpose Pin Control (addresses 29h to 2Fh) ................................................... 48
CHARACTERISTICS AND SPECIFICATIONS ....................................................................... 50
SPECIFIED OPERATING CONDITIONS ............................................................................... 50
ABSOLUTE MAXIMUM RATINGS ......................................................................................... 50
ANALOG INPUT CHARACTERISTICS .................................................................................. 51
A/D DIGITAL FILTER CHARACTERISTICS .......................................................................... 52
ANALOG OUTPUT CHARACTERISTICS .............................................................................. 55
D/A DIGITAL FILTER CHARACTERISTICS .......................................................................... 56
SWITCHING CHARACTERISTICS ........................................................................................ 61
SWITCHING CHARACTERISTICS - CONTROL PORT - I2C FORMAT ............................... 62
SWITCHING CHARACTERISTICS - CONTROL PORT - SPI FORMAT ............................... 63
DC ELECTRICAL CHARACTERISTICS ................................................................................ 64
DIGITAL INTERFACE CHARACTERISTICS ......................................................................... 64
PARAMETER DEFINITIONS ................................................................................................... 65
REFERENCES ......................................................................................................................... 66
PACKAGE DIMENSIONS .................................................................................................... 67
THERMAL CHARACTERISTICS ........................................................................................... 67
3
CS42426
LIST OF FIGURES
Figure 1. Typical Connection Diagram ............................................................................................ 8
Figure 2. Typical Connection Diagram using the PLL ..................................................................... 9
Figure 3. Full-Scale Analog Input .................................................................................................. 10
Figure 4. Full-Scale Output ........................................................................................................... 12
Figure 5. ATAPI Block Diagram (x = channel pair 1, 2, 3)............................................................. 13
Figure 6. Clock Generation ........................................................................................................... 14
Figure 7. Right Justified Serial Audio Formats .............................................................................. 18
Figure 8. I2S Serial Audio Formats................................................................................................ 19
Figure 9. Left Justified Serial Audio Formats ................................................................................ 19
Figure 10. One Line Mode #1 Serial Audio Format ....................................................................... 20
Figure 11. One Line Mode #2 Serial Audio Format ....................................................................... 20
Figure 12. ADCIN1/ADCIN2 Serial Audio Format ......................................................................... 21
Figure 13. OLM Configuration #1 .................................................................................................. 22
Figure 14. OLM Configuration #2 .................................................................................................. 23
Figure 15. OLM Configuration #3 .................................................................................................. 24
Figure 16. OLM Configuration #4 .................................................................................................. 25
Figure 17. Control Port Timing in SPI Mode.................................................................................. 26
Figure 18. Control Port Timing, I2C Slave Mode Write ................................................................. 27
Figure 19. Control Port Timing, I2C Slave Mode Read ................................................................. 27
Figure 20. Single Speed Mode Stopband Rejection ..................................................................... 53
Figure 21. Single Speed Mode Transition Band............................................................................ 53
Figure 22. Single Speed Mode Transition Band (Detail) ............................................................... 53
Figure 23. Single Speed Mode Passband Ripple.......................................................................... 53
Figure 24. Double Speed Mode Stopband Rejection .................................................................... 53
Figure 25. Double Speed Mode Transition Band .......................................................................... 53
Figure 26. Double Speed Mode Transition Band (Detail).............................................................. 54
Figure 27. Double Speed Mode Passband Ripple ........................................................................ 54
Figure 28. Quad Speed Mode Stopband Rejection....................................................................... 54
Figure 29. Quad Speed Mode Transition Band ............................................................................. 54
Figure 30. Quad Speed Mode Transition Band (Detail) ................................................................ 54
Figure 31. Quad Speed Mode Passband Ripple........................................................................... 54
Figure 32. Single Speed (fast) Stopband Rejection ...................................................................... 57
Figure 33. Single Speed (fast) Transition Band ............................................................................ 57
Figure 34. Single Speed (fast) Transition Band (detail) ................................................................ 57
Figure 35. Single Speed (fast) Passband Ripple .......................................................................... 57
Figure 36. Single Speed (slow) Stopband Rejection ..................................................................... 57
Figure 37. Single Speed (slow) Transition Band ........................................................................... 57
Figure 38. Single Speed (slow) Transition Band (detail) ............................................................... 58
Figure 39. Single Speed (slow) Passband Ripple ......................................................................... 58
Figure 40. Double Speed (fast) Stopband Rejection ..................................................................... 58
Figure 41. Double Speed (fast) Transition Band ........................................................................... 58
Figure 42. Double Speed (fast) Transition Band (detail) ............................................................... 58
Figure 43. Double Speed (fast) Passband Ripple ......................................................................... 58
Figure 44. Double Speed (slow) Stopband Rejection ................................................................... 59
Figure 45. Double Speed (slow) Transition Band.......................................................................... 59
Figure 46. Double Speed (slow) Transition Band (detail).............................................................. 59
Figure 47. Double Speed (slow) Passband Ripple........................................................................ 59
Figure 48. Quad Speed (fast) Stopband Rejection ....................................................................... 59
Figure 49. Quad Speed (fast) Transition Band.............................................................................. 59
Figure 50. Quad Speed (fast) Transition Band (detail).................................................................. 60
Figure 51. Quad Speed (fast) Passband Ripple............................................................................ 60
4
CS42426
Figure 52. Quad Speed (slow) Stopband Rejection...................................................................... 60
Figure 53. Quad Speed (slow) Transition Band ............................................................................ 60
Figure 54. Quad Speed (slow) Transition Band (detail) ................................................................ 60
Figure 55. Quad Speed (slow) Passband Ripple .......................................................................... 60
Figure 56. Serial Audio Port Master Mode Timing ........................................................................ 61
Figure 57. Serial Audio Port Slave Mode Timing .......................................................................... 61
Figure 58. Control Port Timing - I2C Format................................................................................. 62
Figure 59. Control Port Timing - SPI Format................................................................................. 63
LIST OF TABLES
Table 1. PLL External Component Values .................................................................................... 15
Table 2. Common OMCK Clock Frequencies .............................................................................. 15
Table 3. Common PLL Output Clock Frequencies....................................................................... 16
Table 4. Slave Mode Clock Ratios ............................................................................................... 16
Table 5. Serial Audio Port Channel Allocations ............................................................................ 17
Table 6. DAC De-Emphasis .......................................................................................................... 34
Table 7. Digital Interface Formats ................................................................................................. 35
Table 8. ADC One_Line Mode ...................................................................................................... 35
Table 9. DAC One_Line Mode ...................................................................................................... 35
Table 10. RMCK Divider Settings ................................................................................................. 37
Table 11. OMCK Frequency Settings ........................................................................................... 38
Table 12. Master Clock Source Select.......................................................................................... 38
Table 13. PLL Clock Frequency Detection.................................................................................... 39
Table 14. Example Digital Volume Settings .................................................................................. 42
Table 15. ATAPI Decode .............................................................................................................. 44
Table 16. Example ADC Input Gain Settings ................................................................................ 45
5
CS42426
NC
NC
VD
VLS
DG ND
RM CK
NC
ADCIN2
ADC_SDO UT
ADCIN1
O M CK
ADC_SCLK
ADC_LRCK
DAC_SDIN4
DAC_SDIN2
DAC_SDIN3
1 PIN DESCRIPTIONS
64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49
DAC_SDIN1 1
48
G PO 1
DAC_SCLK
2
47
G PO 2
DAC_LRCK
3
46
G PO 3
VD
4
45
G PO 4
DG ND
5
44
G PO 5
VLC
6
43
G PO 6
SCL/CCLK
7
42
G PO 7
SDA/CD OUT
8
AD1/CDIN
CS42426
41
VA
9
40
AG ND
AD0/CS
10
39
LPFLT
INT
11
38
M UTEC
RST
12
37
AO UTA1-
AINR-
13
36
AOUT A1+
AINR +
14
35
AOUT B1+
AINL+
15
34
AOUT B1-
AINL-
16
33
AO UTA2-
AOUT A2+
AO UTB2-
AOUT B2+
AOUTA3-
AOUT A3+
AOUTB3-
AOUT B3+
AGND
VA
NC
NC
NC
NC
REFGND
VQ
FILT+
17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32
Pin Name
#
Pin Description
DAC_SDIN1
DAC_SDIN2
DAC_SDIN3
1
64
63
DAC Serial Audio Data Input (Input) - Input for two’s complement serial audio data.
DAC_SCLK
2
DAC Serial Clock (Input/Output) - Serial clock for the DAC serial audio interface.
DAC_LRCK
3
DAC Left Right Clock (Input/Output) - Determines which channel, Left or Right, is currently active on
the DAC serial audio data line.
VD
4
51
Digital Power (Input) - Positive power supply for the digital section.
DGND
5
52
Digital Ground (Input) - Ground reference. Should be connected to digital ground.
VLC
6
Control Port Power (Input) - Determines the required signal level for the control port.
SCL/CCLK
7
Serial Control Port Clock (Input) - Serial clock for the serial control port. Requires an external pull-up
resistor to the logic interface voltage in I2C mode as shown in the Typical Connection Diagram.
SDA/CDOUT
8
Serial Control Data (Input/Output) - SDA is a data I/O line in I2C mode and requires an external pull-up
resistor to the logic interface voltage, as shown in the Typical Connection Diagram. CDOUT is the output
data line for the control port interface in SPI mode.
AD1/CDIN
9
Address Bit 1 (I2C)/Serial Control Data (SPI) (Input) - AD1 is a chip address pin in I2C mode; CDIN is
the input data line for the control port interface in SPI mode.
AD0/CS
10
Address Bit 0 (I2C)/Control Port Chip Select (SPI) (Input) - AD0 is a chip address pin in I2C mode; CS
is the chip select signal in SPI mode.
6
CS42426
INT
11
Interrupt (Output) - The CS42426 will generate an interrupt condition as per the Interrupt Mask register.
See “Interrupts” on page 28 for more details.
RST
12
Reset (Input) - The device enters a low power mode and all internal registers are reset to their default
settings when low.
AINRAINR+
13
14
Differential Right Channel Analog Input (Input) - Signals are presented differentially to the delta-sigma
modulators via the AINR+/- pins.
AINL+
AINL-
15
16
Differential Left Channel Analog Input (Input) - Signals are presented differentially to the delta-sigma
modulators via the AINL+/- pins.
VQ
17
Quiescent Voltage (Output) - Filter connection for internal quiescent reference voltage.
FILT+
18
Positive Voltage Reference (Output) - Positive reference voltage for the internal sampling circuits.
REFGND
19
Reference Ground (Input) - Ground reference for the internal sampling circuits.
AOUTA1 +,AOUTB1 +,AOUTA2 +,AOUTB2 +,AOUTA3 +,AOUTB3 +,-
36,37 Differential Analog Output (Output) - The full-scale differential analog output level is specified in the
35,34 Analog Characteristics specification table.
32,33
31,30
28,29
27,26
VA
24
41
Analog Power (Input) - Positive power supply for the analog section.
AGND
25
40
Analog Ground (Input) - Ground reference. Should be connected to analog ground.
MUTEC
38
Mute Control (Output) - The Mute Control pin outputs high impedance following an initial power-on condition or whenever the PDN bit is set to a ‘1’, forcing the codec into power-down mode. The signal will
remain in a high impedance state as long as the part is in power-down mode. The Mute Control pin goes
to the selected “active” state during reset, muting, or if the master clock to left/right clock frequency ratio
is incorrect. This pin is intended to be used as a control for external mute circuits to prevent the clicks
and pops that can occur in any single supply system. The use of external mute circuits are not mandatory but may be desired for designs requiring the absolute minimum in extraneous clicks and pops.
LPFLT
39
PLL Loop Filter (Output) - An RC network should be connected between this pin and ground.
GPO7
GPO6
GPO5
GPO4
GPO3
GPO2
GPO1
42
43
44
45
46
47
48
General Purpose Output (Output) - These pins can be configured as general purpose output pins, an
ADC overflow interrupt or Mute Control outputs according to the General Purpose Pin Control registers.
VLS
53
Serial Port Interface Power (Input) - Determines the required signal level for the serial port interfaces.
RMCK
55
Recovered Master Clock (Output) - Recovered master clock output from the External Clock Reference
(OMCK, pin 59) or the PLL which is locked to the incoming ADC_LRCK.
ADC_SDOUT
56
ADC Serial Data Output (Output) - Output for two’s complement serial audio PCM data from the output
of the internal and external ADCs.
ADCIN1
ADCIN2
58
57
External ADC Serial Input (Input) - The CS42426 provides for up to two external stereo analog to digital
converter inputs to provide a maximum of six channels on one serial data output line when the CS42426
is placed in One Line mode.
OMCK
59
External Reference Clock (Input) - External clock reference that must be within the ranges specified in
the register “OMCK Frequency (OMCK Freqx)” on page 38.
ADC_LRCK
60
ADC Left/Right Clock (Input/Output) - Determines which channel, Left or Right, is currently active on
the ADC serial audio data line.
ADC_SCLK
61
ADC Serial Clock (Input/Output) - Serial clock for the ADC serial audio interface.
7
CS42426
2 TYPICAL CONNECTION DIAGRAMS
+3.3 V to +5 V
10 µF
10 µF
+
0.1 µF
0.01 µF
0.01 µF 0.1 µF +
+
0.1 µF
0.01 µF
0.01 µF 0.1 µF +
51
VD
4
VD
24
VA
41
VA
AOUTA1+
48
47
46
45
44
43
42
+2.5 V
to +5 V
53
0.1 µF
59
OSC
AOUTA1-
GPO1
GPO2
AOUTB1+
GPO3
AOUTB1-
GPO4
GPO5
AOUTA2+
GPO6
AOUTA2-
GPO7
AOUTB2+
VLS
AOUTB2-
OMCK
AOUTA3+
58
CS5361
A/D Converter
CS5361
A/D Converter
57
55
ADCIN1
AOUTA3-
ADCIN2
AOUTB3+
RMCK
AOUTB3-
+5 V
10 µF
10 µF
36
Analog Conditioning
and Muting
37
35
Analog Conditioning
and Muting
34
32
Analog Conditioning
and Muting
33
31
Analog Conditioning
and Muting
30
28
Analog Conditioning
and Muting
29
27
Analog Conditioning
and Muting
26
CS42426
56
60
Digital Audio
Processor
61
3
2
1
64
63
ADC_SDOUT
ADC_LRCK
+VA
ADC_SCLK
MUTEC
11
MicroController
7
8
9
+1.8V
to +5V
***
DAC_LRCK
*** Pull up or down as required on startup
DAC_SDIN1
AINL+
DAC_SDIN2
DAC_SDIN3
INT
AINR+
15
16
SCL/CCLK
AINR-
Analog
2700
InputpF*
Buffer *
Left Analog Input
Analog
InputpF*
2700
Buffer *
Right Analog Input
14
RST
13
SDA/CDOUT
* See CDB42428 for a recommended filter.
AD1/CDIN
VQ
AD0/CS
FILT+
2 kΩ
See
Note
2 kΩ
10
Mute
Drive
***
DAC_SCLK
AINL-
12
38
17
18
+
+
6
REFGND
VLC
0.1 µF
LPFLT
19
0.1 µF
DGND DGND
52
5
AGND
25
AGND
40
CFILT**
Connect DGND and AGND at single point near Codec
Figure 1. Typical Connection Diagram
8
4.7 µF
100 µF
39
RFILT**
Note: Resistors are required for
I2C control port operation
0.1 µF
** Refer to Table 1
for proper values
CRIP**
CS42426
+3.3 V to +5 V
10 µF
10 µF
0.1 µF
+
0.1 µF
+
0.01 µF 0.1 µF +
0.01 µF
0.01 µF 0.1 µF +
0.01 µF
51
4
41
VD
VD
VA
47
46
45
44
43
42
+1.8 V
to +5.0 V
AOUTA1-
GPO1
GPO2
AOUTB1+
GPO3
AOUTB1-
GPO4
GPO5
AOUTA2+
GPO6
AOUTA2-
GPO7
53
0.1 µF
59
AOUTB2+
VLS
AOUTB2OMCK
AOUTA3+
58
57
ADCIN1
AOUTA3-
56
60
DVD
Processor
61
36
Analog Conditioning
and Muting
37
35
Analog Conditioning
and Muting
34
32
Analog Conditioning
and Muting
33
31
Analog Conditioning
and Muting
30
28
Analog Conditioning
and Muting
29
ADCIN2
CS42426
55
10 µF
24
VA
AOUTA1+
48
+5 V
10 µF
AOUTB3+
AOUTB3-
27
Analog Conditioning
and Muting
26
RMCK
ADC_SDOUT
+VA
ADC_LRCK
MUTEC
ADC_SCLK
38
Mute
Drive
***
***
27 MHz
3
2
1
64
63
11
12
7
8
9
See
Note
DAC_SCLK
DAC_SDIN1
AINL+
15
Analog
2700
InputpF*
DAC_SDIN2
DAC_SDIN3
AINL-
AINR+
16
RST
AINR-
13
Analog
InputpF*
2700
Buffer *
* See CDB42428 for a recommended filter.
AD1/CDIN
AD0/CS
VQ
17
18
+
+
REFGND
VLC
0.1 µF
LPFLT
19
0.1 µF
0.1 µF
DGND DGND
5
52
AGND
25
AGND
40
4.7 µF
100 µF
39
** Refer to Table 1
for proper values
RFILT**
Note: Resistors are required for
I2C control port operation
Right Analog Input
SCL/CCLK
SDA/CDOUT
FILT+
6
Left Analog Input
Buffer *
14
INT
2 kΩ
2 kΩ
10
*** Pull up or down as required on startup
DAC_LRCK
CFILT**
CRIP**
Connect DGND and AGND at single point near Codec
Figure 2. Typical Connection Diagram using the PLL
9
CS42426
3 APPLICATIONS
3.1
Overview
The CS42426 is a highly integrated mixed signal 24-bit audio codec comprised of 2 analog-to-digital converters (ADC), implemented using multi-bit delta-sigma techniques, and 6 digital-to-analog converters
(DAC). Other functions integrated within the codec include independent digital volume controls for each
DAC, digital de-emphasis filters for DAC, digital gain control for ADC channels, ADC high-pass filters,
and an on-chip voltage reference. All serial data is transmitted through one configurable serial audio interface for the ADC with enhanced one line modes of operation allowing up to 6 channels of serial audio data
on one data line. All functions are configured through a serial control port operable in SPI mode or in I2C
mode. Figure 1 shows the recommended connections for the CS42426.
The CS42426 operates in one of three oversampling modes based on the input sample rate. Mode selection
is determined by the FM bits in register “Functional Mode (address 03h)” on page 33. Single-Speed mode
(SSM) supports input sample rates up to 50 kHz and uses a 128x oversampling ratio. Double-Speed mode
(DSM) supports input sample rates up to 100 kHz and uses an oversampling ratio of 64x. Quad-Speed
mode (QSM) supports input sample rates up to 192 kHz and uses an oversampling ratio of 32x.
Using the integrated PLL, a low jitter clock is recovered from the ADC LRCK input signal. The recovered
clock or an externally supplied clock attached to the OMCK pin can be used as the System Clock.
3.2
3.2.1
Analog Inputs
Line Level Inputs
AINR+, AINR-, AINL+, and AINL- are the line level differential analog inputs. These pins are internally
biased to the DC quiescent reference voltage, VQ, of approximately 2.7 V. The level of the signal can be
adjusted for the left and right ADC independently through the ADC Left and Right Channel Gain Control
Registers on page 45. The ADC output data is in 2’s complement binary format. For inputs above positive
full scale or below negative full scale, the ADC will output 7FFFFFH or 800000H, respectively and cause
the ADC Overflow bit in the register “Interrupt Status (address 20h) (Read Only)” on page 46 to be set to
a ‘1’. The GPO pins may also be configured to indicate an overflow condition has occurred in the ADC.
See “General Purpose Pin Control (addresses 29h to 2Fh)” on page 48 for proper configuration. Figure 3
shows the full-scale analog input levels.
4.1 V
2.7 V
AIN+
1.3 V
4.1 V
AIN-
2.7 V
1.3 V
Full-Scale Input Level= (AIN+) - (AIN-)= 5.6 Vpp
Figure 3. Full-Scale Analog Input
10
CS42426
3.2.2
External Input Filter
The analog modulator samples the input at 6.144 MHz (internal MCLK=12.288 MHz). The digital filter
will reject signals within the stopband of the filter. However, there is no rejection for input signals which
are (n × 6.144 MHz) the digital passband frequency, where n=0,1,2,... Refer to the CDB42418 for a recommended analog input buffer that will attenuate any noise energy at 6.144 MHz, in addition to providing
the optimum source impedance for the modulators. The use of capacitors which have a large voltage coefficient (such as general purpose ceramics) must be avoided since these can degrade signal linearity.
3.2.3
High Pass Filter and DC Offset Calibration
The high pass filter continuously subtracts a measure of the DC offset from the output of the decimation
filter. The high pass filter can be independently enabled and disabled. If the HPF_Freeze bit is set during
normal operation, the current value of the DC offset for the corresponding channel is frozen and this DC
offset will continue to be subtracted from the conversion result. This feature makes it possible to perform
a system DC offset calibration by:
1) Running the CS42426 with the high pass filter enabled until the filter settles. See the Digital Filter
Characteristics for filter settling time.
2) Disabling the high pass filter and freezing the stored DC offset.
The high pass filters are controlled using the HPF_FREEZE bit in the register “Misc Control (address
05h)” on page 36.
3.3
3.3.1
Analog Outputs
Line Level Outputs and Filtering
The CS42426 contains on-chip buffer amplifiers capable of producing line level differential outputs. These
amplifiers are biased to a quiescent DC level of approximately VQ.
The delta-sigma conversion process produces high frequency noise beyond the audio passband, most of
which is removed by the on-chip analog filters. The remaining out-of-band noise can be attenuated using
an off-chip low pass filter. The recommended output filter configuration is shown in the CDB42418. This
filter configuration accounts for the normally differing AC loads on the AOUT+ and AOUT- differential
output pins. It also shows an AC coupling configuration which minimizes the number of required AC coupling capacitors.
11
CS42426
The CS42426 is a linear phase design and does not include phase or amplitude compensation for an external filter. Therefore, the DAC system phase and amplitude response will be dependent on the external analog circuitry. Figure 4 shows the full-scale analog output levels.
3.95 V
2.7 V
AOUT+
1.45 V
3.95 V
AOUT-
2.7 V
1.45 V
Full-Scale Output Level= (AIN +) - (AIN -)= 5 Vpp
Figure 4. Full-Scale Output
3.3.2
Interpolation Filter
To accommodate the increasingly complex requirements of digital audio systems, the CS42426 incorporates selectable interpolation filters for each mode of operation. A “fast” and a “slow” roll-off filter is available in each of Single, Double, and Quad Speed modes. These filters have been designed to accommodate
a variety of musical tastes and styles. The FILT_SEL bit found in the register “Misc Control (address 05h)”
on page 36 is used to select which filter is used. Filter response plots can be found in Figures 32 to 55.
3.3.3
Digital Volume and Mute Control
Each DAC’s output level is controlled via the Volume Control registers operating over the range of 0 to
-127 dB attenuation with 0.5 dB resolution. See “Volume Control (addresses 0Fh, 10h, 11h, 12h, 13h,
14h)” on page 42. Volume control changes are programmable to ramp in increments of 0.125 dB at the rate
controlled by the SZC[1:0] bits in the Digital Volume Control register. See “Volume Control (address
0Dh)” on page 40.
Each output can be independently muted via mute control bits in the register “Channel Mute (address
0Eh)” on page 41. When enabled, each XX_MUTE bit attenuates the corresponding DAC to its maximum
value (-127 dB). When the XX_MUTE bit is disabled, the corresponding DAC returns to the attenuation
level set in the Volume Control register. The attenuation is ramped up and down at the rate specified by
the SZC[1:0] bits.
The Mute Control pin, MUTEC, is typically connected to an external mute control circuit. The Mute Control pin is tri-stated during power up or in power down mode by setting the PDN bit in the register “Power
Control (address 02h)” on page 33 to a ‘1’. Once out of power-down mode the pin can be controlled by the
user via the control port, or automatically asserted high when zero data is present on all DAC inputs, or
when serial port clock errors are present. To prevent large transients on the output, it is desirable to mute
the DAC outputs before the Mute Control pin is asserted. Please see the MUTEC pin in the Pin Descriptions section for more information.
12
CS42426
Each of the GPO1-GPO7 can be programmed to provide a hardware MUTE signal to individual circuits.
Each pin can be programmed as an output, with specific muting capabilities as defined by the function bits
in the register “General Purpose Pin Control (addresses 29h to 2Fh)” on page 48.
3.3.4
ATAPI Specification
The CS42426 implements the channel mixing functions of the ATAPI CD-ROM specification. The
ATAPI functions are applied per A-B pair. Refer to Table 15 on page 44 and Figure 5 for additional information.
A Channel
Volum e
Control
Left Channel
Audio Data
Σ
DA C_SDINx
Right Channel
Audio Data
M UTE
A OUTAx
M UTE
AOUTBx
Σ
B Channel
Volume
Control
Figure 5. ATAPI Block Diagram (x = channel pair 1, 2, 3)
13
CS42426
3.4
Clock Generation
The clock generation for the CS42426 is shown in the figure below. The internal MCLK is derived from
the output of the PLL or a master clock source attached to OMCK. The mux selection is controlled by the
SW_CTRLx bits and can be configured to manual switch mode only, or automatically switch on loss of
PLL lock to the other source input.
RMCK_DIVx bits
00
2
01
4
10
X2
11
Internal
MCLK
ADC_LRCK
(slave mode)
PLL (256Fs)
8.192 49.152 MHz
00
01
PLL_LRCK bit
O MCK
RMCK
single
speed
256
Auto Detect
Input Clock
1,1.5, 2, 4
double
speed
01
D AC_LRCK
10
128
DAC _FMx bits
quad
speed
SW_CTRLx bits
(manual or auto
switch)
00
64
DAC_OLx
or ADC_O Lx bits
00
01
10
not O LM
128FS
single
speed
256FS
OLM #1
DAC_SCLK
OLM #2
4
double
speed
2
00
01
quad
speed
1
ADC_LRCK
10
ADC_FMx bits
ADC_O Lx and
ADC _SP SELx bits
00
01
10
not O LM
128FS
256FS
O LM #1
ADC_SCLK
OLM #2
Figure 6. Clock Generation
3.4.1
PLL and Jitter Attenuation
The PLL can be configured to lock onto the incoming ADC_LRCK signal from the ADC Serial Port and
generate the required internal master clock frequency. There are some applications where low jitter in the
recovered clock, presented on the RMCK pin, is important. For this reason, the PLL has been designed to
have good jitter attenuation characteristics. By setting the PLL_LRCK bit to a ‘1’ in the register “Clock
Control (address 06h)” on page 37, the PLL will lock to the incoming ADC_LRCK and generate an output
master clock (RMCK) of 256Fs. Table 3 below shows the output of the PLL with typical input Fs values
for ADC_LRCK.
The PLL behavior is affected by the external filter component values. Figure 1 shows the required configuration of the external filter components. The set of component values required for 32 kHz to 192 kHz
14
CS42426
sample rate applications are shown in Table 1. The lock time is the worst case for an Fs transition from unlocked state to locking to 192 kHz.
Fs Range (kHz) RFILT (kΩ) CFILT (pF) CRIP (pF)
32 to 192
10
2700
Settling time
680
11 ms
Table 1. PLL External Component Values
It is important to treat the LPFLT pin as a low level analog input. It is suggested that the ground end of the
PLL filter be returned directly to the AGND pin independently of the digital ground plane.
3.4.2
OMCK System Clock Mode
A special clock switching mode is available that allows the clock that is input through the OMCK pin to
be used as the internal master clock. This feature is controlled by the SW_CTRLx bits in register “Clock
Control (address 06h)” on page 37. An advanced auto switching mode is also implemented to maintain
master clock functionality. The clock auto switching mode allows the clock input through OMCK to be
used as a clock in the system without any disruption when the PLL loses lock, for example, when the
LRCK is removed from ADC_LRCK. This clock switching is done glitch free.
3.4.3
Master Mode
In master mode, the serial interface timings are derived from an external clock attached to OMCK or the
output of the PLL with an input reference to the ADC_LRCK input from the ADC serial port. The DAC
Serial Port and ADC Serial Port can both be masters only when OMCK is used as the clock source. When
using the PLL output, the ADC Serial Port must be slave and the DAC Serial Port can operate in Master
Mode. Master clock selection and operation is configured with the SW_CTRL1:0 and CLK_SEL bits in
the Clock Control Register (See “Clock Control (address 06h)” on page 37).
The sample rate to OMCK ratios and OMCK frequency requirements for Master mode operation are
shown in Table 2.
OMCK (MHz)
Sample
Rate
(kHz)
48
96
192
Single Speed
(4 to 50 kHz)
Double Speed
(50 to 100 kHz)
Quad Speed
(100 to 192 kHz)
256x
384x
512x
128x
192x
256x
64x
96x
128x
12.2880 18.4320 24.5760
12.2880 18.4320 24.5760
12.2880 18.4320 24.5760
Table 2. Common OMCK Clock Frequencies
3.4.4
Slave Mode
In Slave mode, DAC_LRCK, DAC_SCLK and/or ADC_LRCK and ADC_SCLK operate as inputs. The
Left/Right clock signal must be equal to the sample rate, Fs and must be synchronously derived from the
supplied master clock, OMCK or must be synchronous to the supplied ADC_LRCK used as the input to
15
CS42426
the PLL. In this latter scenario the PLL output becomes the internal master clock. The supported PLL output frequencies are shown in Table 3 below.
PLL Output (MHz)
Sample
Rate
(kHz)
Single Speed
(4 to 50 kHz)
Double Speed
(50 to 100 kHz)
Quad Speed
(100 to 192 kHz)
32
44.1
48
64
88.2
96
176.4
192
256x
8.1920
11.2896
12.2880
-
256x
16.3840
22.5792
24.5760
-
256x
45.1584
49.1520
Table 3. Common PLL Output Clock Frequencies
The serial bit clock, DAC_SCLK and/or ADC_SCLK, must be synchronous to the corresponding
DAC_LRCK/ADC_LRCK and be equal to 128x, 64x, 48x or 32x Fs depending on the interface format
selected and desired speed mode. One Line Mode #1 is supported in Slave Mode. One Line Mode #2 is
not supported. Refer to Table 4 for required clock ratios.
Single Speed
Double Speed
Quad Speed
One Line Mode #1
OMCK/LRCK Ratio
256x, 512x
128x, 256x
128x
256x
SCLK/LRCK Ratio
32x, 48x, 64x, 128x
32x, 64x
32x, 64x
128x
Table 4. Slave Mode Clock Ratios
3.5
3.5.1
Digital Interfaces
Serial Audio Interface Signals
The CS42426 interfaces to an external Digital Audio Processor via two independent serial ports, the
DAC serial port, DAC_SP and the ADC serial port, ADC_SP. The digital output of the internal ADCs use
the ADC_SDOUT pin and can be configured to use either the ADC or DAC serial port timings. These configuration bits and the selection of Single, Double or Quad Speed mode for DAC_SP and ADC_SP are
found in register “Functional Mode (address 03h)” on page 33.
The serial interface clocks, ADC_SCLK for ADC_SP and DAC_SCLK for DAC_SP, are used for transmitting and receiving audio data. Either ADC_SCLK or DAC_SCLK can be generated by the CS42426
(master mode) or it can be input from an external source (slave mode). Master or Slave mode selection is
made using bits DAC_SP M/S and ADC_SP M/S in register “Misc Control (address 05h)” on page 36.
The Left/Right clock (ADC_LRCK or DAC_LRCK) is used to indicate left and right data frames and the
start of a new sample period. It may be an output of the CS42426 (master mode), or it may be generated
by an external source (slave mode). As described in later sections, particular modes of operation do allow
the sample rate, Fs, of the ADC_SP and the DAC_SP to be different, but must be multiples of each other.
The serial data interface format selection (left/right justified, I2S or one line mode) for the ADC serial port
data out pin, ADC_SDOUT, and the DAC input pins, DAC_SDIN1:3, is configured using the appropriate
16
CS42426
bits in the register “Interface Formats (address 04h)” on page 34. The serial audio data is presented in 2's
complement binary form with the MSB first in all formats.
DAC_SDIN1, DAC_SDIN2, and DAC_SDIN3 are the serial data input pins supplying the internal DAC.
ADC_SDOUT, the ADC data output pin, carries data from the two internal 24-bit ADCs and, when configured for one-line mode, up to four additional ADC channels attached externally to the signals ADCIN1
and ADCIN2 (typically two CS5361 stereo ADCs). When operated in One Line Data Mode, 6 channels of
DAC data are input on DAC_SDIN1 and 6 channels of ADC data are output on ADC_SDOUT. Table 5
outlines the serial port channel allocations.
Serial Inputs / Outputs
DAC_SDIN1
left channel DAC #1
right channel DAC #2
one line mode DAC channels 1,2,3,4,5,6
DAC_SDIN2
left channel DAC #3
right channel DAC #4
one line mode not used
DAC_SDIN3
left channel DAC #5
right channel DAC #6
one line mode not used
ADC_SDOUT
left channel ADC #1
right channel ADC #2
one line mode ADC channels 1,2,3,4,5,6
ADCIN1
left channel External ADC #3
right channel External ADC #4
ADCIN2
left channel External ADC #5
right channel External ADC #6
Table 5. Serial Audio Port Channel Allocations
17
CS42426
3.5.2
Serial Audio Interface Formats
The DAC_SP and ADC_SP digital audio serial ports support 5 formats with varying bit depths from 16 to
24 as shown in Figure 7, Figure 8, Figure 9, Figure 10 and Figure 11. These formats are selected using the
configuration bits in the registers, “Functional Mode (address 03h)” on page 33 and “Interface Formats
(address 04h)” on page 34. For the diagrams below, single-speed mode is equivalent to Fs = 32, 44.1,
48kHz; double-speed mode is for Fs = 64, 88.2, 96 kHz; and quad-speed mode is for Fs = 176.4, 196 kHz.
DA C_L RC K
AD C_L RC K
R ight C han nel
Left C hannel
DAC _SC LK
ADC _SC LK
D AC_ SDIN x
AD C_S DOU T
1 5 1 4 1 3 1 2 1 1 10
9
8
7
6
5
4
3
2
1
0
1 5 1 4 1 3 1 2 1 1 10
Right Justified Mode, Data Valid on Rising Edge of SCLK
Bits/Sample
SCLK Rate(s)
Master
16
24
64 Fs
Notes
Slave
48, 64, 128 Fs
single-speed mode
64 Fs
64 Fs
double-speed mode
64 Fs
64 Fs
quad-speed mode
64, 128, 256 Fs
64, 128 Fs
single-speed mode
64 Fs
64 Fs
double-speed mode
64 Fs
64 Fs
quad-speed mode
Figure 7. Right Justified Serial Audio Formats
18
9
8
7
6
5
4
3
2
1
0
CS42426
DA C_LR CK
AD C_LR CK
Le ft C h a nn e l
R ig h t C ha n n e l
DAC _SC LK
ADC _SC LK
D AC_ SDIN x
AD C_ SDOUT
MSB
+5 +4 +3 +2 +1
-1 -2 -3 -4 -5
LS B
MSB
-1 -2 -3 -4
+5 +4 +3 +2 +1
LSB
I2S Mode, Data Valid on Rising Edge of SCLK
Bits/Sample
SCLK Rate(s)
Notes
Master
16
18 to 24
Slave
64 Fs
48, 64, 128 Fs
single-speed mode
64 Fs
64 Fs
double-speed mode
64 Fs
64 Fs
quad-speed mode
64, 128, 256 Fs
48, 64, 128 Fs
single-speed mode
64 Fs
64 Fs
double-speed mode
64 Fs
64 Fs
quad-speed mode
Figure 8.
D AC _LRC K
ADC _LRC K
I2 S
Serial Audio Formats
L eft C han nel
Righ t C han ne l
DAC_SCLK
ADC_SCLK
DAC_SDIN x
AD C_SDO UT
MSB
-1 -2 -3 -4 -5
+5 +4 +3 +2 +1
LSB
MSB
-1 -2 -3 -4
+5 +4 +3 +2 +1
LSB
Left Justified Mode, Data Valid on Rising Edge of SCLK
Bits/Sample
SCLK Rate(s)
Master
16
18 to 24
Notes
Slave
64 Fs
32, 48, 64, 128 Fs
single-speed mode
64 Fs
32, 64 Fs
double-speed mode
64 Fs
32, 64 Fs
quad-speed mode
64, 128, 256 Fs
48, 64, 128 Fs
single-speed mode
64 Fs
64 Fs
double-speed mode
64 Fs
64 Fs
quad-speed mode
Figure 9. Left Justified Serial Audio Formats
19
CS42426
D AC _LRCK
ADC _LRCK
64 clks
64 clks
Left Channel
Right C hannel
D AC_SCLK
AD C_SCLK
DAC _SDIN1
M SB
ADC_SDO UT
LSB M SB
LS B M SB
LS B
M SB
LSB M SB
LS B M SB
D AC 1
D AC3
D AC 5
D AC2
D AC4
20 clks
20 clks
20 clks
20 clks
20 clks
A DC 1
A DC 3
A DC 5
A DC2
A DC 4
A DC6
20 clks
20 clks
20 clks
20 clks
20 clks
20 clks
LSB
M SB
LSB
MSB
D AC6
20 clks
One Line Data Mode #1, Data Valid on Rising Edge of SCLK
Bits/Sample
SCLK Rate(s)
Master
20
Notes
Slave
128 Fs
128 Fs
single-speed mode
128 Fs
128Fs
double-speed mode
Figure 10. One Line Mode #1 Serial Audio Format
DAC_LRCK
ADC_LRCK
128 clks
128 clks
Left Channel
Right Channel
DAC_SCLK
ADC_SCLK
DAC_SDIN1
MSB
LSB MSB
LSB MSB
LSB
MSB
LSB MSB
LSB MSB
DAC1
DAC3
DAC5
DAC2
DAC4
DAC6
24 clks
24 clks
24 clks
24 clks
24 clks
24 clks
ADC1
ADC3
ADC5
ADC2
ADC4
ADC6
24 clks
24 clks
24 clks
24 clks
24 clks
24 clks
ADC_SDOUT
One Line Data Mode #2, Data Valid on Rising Edge of SCLK
Bits/Sample
SCLK Rate(s)
Master
24
256 Fs
Notes
Slave
not supported
single-speed mode
Figure 11. One Line Mode #2 Serial Audio Format
20
CS42426
3.5.3
ADCIN1/ADCIN2 Serial Data Format
The two serial data lines which interface to the optional external ADCs, ADCIN1 and ADCIN2, support
only left-justified, 24-bit samples at 64Fs or 128Fs. This interface is not affected by any of the serial port
configuration register bit settings. These serial data lines are used when supporting One Line Mode of operation with external ADCs attached. If these signals are not being used, they should be tied together and
wired to GND via a pull-down resistor.
DA C_LRCK
A DC_LRCK
Left Chann el
R igh t Chan nel
DA C_S CLK
A DC_S CLK
M SB
A DCIN1/2
-1 -2 -3 -4 -5
+5 +4 +3 +2 +1
LS B
M SB
-1 -2 -3 -4
+5 +4 +3 +2 +1
LSB
Left Justified Mode, Data Valid on Rising Edge of SCLK
Bits/Sample
24
SCLK Rate(s)
Notes
64, 128 Fs
single-speed mode, Fs= 32, 44.1, 48 kHz
64 Fs
double-speed mode, Fs= 64, 88.2, 96 kHz
not supported
quad-speed mode, Fs= 176.4, 192 kHz
Figure 12. ADCIN1/ADCIN2 Serial Audio Format
For proper operation, the CS42426 must be configured to select which SCLK/LRCK is being used to clock
the external ADCs. The EXT ADC SCLK bit in register “Misc Control (address 05h)” on page 36, must
be set accordingly. Set this bit to ‘1’ if the external ADCs are wired using the DAC_SP clocks. If the ADCs
are wired to use the ADC_SP clocks, set this bit to ‘0’.
21
CS42426
3.5.4
One Line Mode(OLM) Configurations
3.5.4.1
OLM Config #1
One Line Mode Configuration #1 can support up to 6 channels of DAC data, and 6 channels of ADC data.
This is the only configuration which will support up to 24-bit samples at a sampling frequency of 48 kHz
on all channels for both the DAC and ADC.
Register / Bit Settings
Description
Functional Mode Register (addr = 03h)
Set DAC_FMx = ADC_FMx = 00,01,10
DAC_LRCK must equal ADC_LRCK; sample rate conversion not supported
Set ADC_CLK_SEL = 0
Configure ADC_SDOUT to be clocked from the DAC_SP clocks.
Interface Format Register (addr = 04h)
Set DIFx bits to proper serial format
Select the digital interface format when not in one line mode
Set ADC_OLx bits = 00,01,10
Select ADC operating mode, see table below for valid combinations
Set DAC_OLx bits = 00,01,10
Select DAC operating mode, see table below for valid combinations
Misc. Control Register (addr = 05h)
Set DAC_SP M/S = 1
Configure DAC Serial Port to master mode.
Set ADC_SP M/S = 1
Configure ADC Serial Port to master mode.
Set EXT ADC SCLK = 0
Identify external ADC clock source as ADC Serial Port.
DAC Mode
Not One Line Mode
ADC Mode
One Line Mode #1
Not One
Line Mode
DAC_SCLK=64Fs
DAC_SCLK=128Fs
DAC_LRCK=SSM/DSM/QSM DAC_LRCK=SSM/DSM
ADC_SCLK=64Fs
ADC_LRCK=DAC_LRCK
One Line
Mode #1
DAC_SCLK=128Fs
DAC_LRCK=SSM/DSM
ADC_SCLK=64Fs
ADC_LRCK=DAC_LRCK
One Line
Mode #2
DAC_SCLK=256Fs
DAC_LRCK=SSM
ADC_SCLK=64Fs
ADC_LRCK=DAC_LRCK
One Line Mode #2
not valid
DAC_SCLK=128Fs
DAC_LRCK=SSM/DSM
ADC_SCLK=64Fs
ADC_LRCK=DAC_LRCK
not valid
DAC_SCLK=256Fs
DAC_LRCK=SSM
ADC_SCLK=64Fs
ADC_LRCK=DAC_LRCK
not valid
MC LK
64Fs
LRC K
AD C_SC LK
SC LK
M CLK
ADC _LR CK
R MCK
S DOU T1
AD CIN 1
S DOU T2
AD CIN 2
CS5361
64Fs,128Fs, 256Fs
D AC _S CLK
SC LK _POR T1
D AC _LR CK
LRC K_POR T1
ADC Data
AD C_SD OUT
CS5361
SD IN_POR T1
SC LK _POR T2
LRC K_POR T2
D AC_SD IN1
D AC_SD IN2
SD OUT1_PORT2
D AC_SD IN3
SD OUT3_PORT2
CS42426
Figure 13. OLM Configuration #1
22
SD OUT2_PORT2
DIG ITAL AU DIO
PROC ESSOR
CS42426
3.5.4.2
OLM Config #2
This configuration will support up to 6 channels of DAC data, 6 channels of ADC data and will handle up
to 20-bit samples at a sampling frequency of 96 kHz on all channels for both the DAC and ADC. The output data stream of the internal and external ADCs is configured to use the ADC_SDOUT output and run
at the DAC Serial Port sample frequency.
Register / Bit Settings
Description
Functional Mode Register (addr = 03h)
Set DAC_FMx = 00,01,10
DAC_LRCK can run at SSM, DSM or QSM independent of ADC_LRCK
Set ADC_FMx = 00,01,10
ADC_LRCK can run at SSM, DSM or QSM independent of DAC_LRCK
Set ADC_CLK_SEL = 1
Configure ADC_SDOUT to be clocked from the ADC_SP clocks.
Interface Format Register (addr = 04h)
Set DIFx bits to proper serial format
Select the digital interface format when not in one line mode
Set ADC_OLx bits = 00,01,10
Select ADC operating mode, see table below for valid combinations
Set DAC_OLx bits = 00,01
Select DAC operating mode, see table below for valid combinations
Misc. Control Register (addr = 05h)
Set CODEC_SP M/S = 1
Set CODEC Serial Port to master mode.
Set SAI_SP M/S = 1
Set Serial Audio Interface Port to master mode.
Set EXT ADC SCLK = 1
Identify external ADC clock source as DAC Serial Port.
DAC Mode
Not One Line Mode
ADC Mode
One Line Mode #1
Not One
Line Mode
DAC_SCLK=64Fs
DAC_LRCK=SSM/DSM/QSM
ADC_SCLK=64Fs
ADC_LRCK=SSM/DSM/QSM
DAC_SCLK=128Fs
DAC_LRCK=SSM
ADC_SCLK=64Fs
ADC_LRCK=SSM/DSM/QSM
One Line
Mode #1
DAC_SCLK=64Fs
DAC_LRCK=SSM/DSM
ADC_SCLK=128Fs
ADC_LRCK=CX_LRCK
DAC_SCLK=128Fs
DAC_LRCK=SSM
ADC_SCLK=128Fs
ADC_LRCK=CX_LRCK
One Line
Mode #2
DAC_SCLK=64Fs
DAC_LRCK=SSM
ADC_SCLK=256Fs
ADC_LRCK=CX_LRCK
not valid
One Line Mode #2
not valid
not valid
not valid
M CLK
LRCK
ADC_SCLK
S CLK
A DC_LRCK
MCLK
RM CK
S DOUT1
A DCIN1
S DOUT2
A DCIN2
64Fs ,12 8Fs,
256Fs
SCLK_P ORT1
LRCK _PO RT1
ADC Data
SDIN_PORT1
A DC_SDO UT
CS5361
CS5361
64Fs ,12 8Fs
DAC_S CLK
SCLK_P ORT2
DA C_LRCK
LRCK _PO RT2
DAC_SDIN1
DAC_SDIN2
S DO UT1_P ORT2
DAC_SDIN3
S DO UT3_P ORT2
CS42426
S DO UT2_P ORT2
DIG ITAL AUDIO
P RO CESSO R
Figure 14. OLM Configuration #2
23
CS42426
3.5.4.3
OLM Config #3
This configuration will support up to 6 channels of DAC data, and 6 channels of ADC data. OLM Config
#3 will handle up to 20-bit ADC samples at an Fs of 48 kHz and 24-bit DAC samples at an Fs of 48 kHz.
Since the ADCs data stream is configured to use the ADC_SDOUT output and the internal and external
ADCs are clocked from the ADC_SP, then the sample rate for the DAC Serial Port can be different from
the sample rate of the ADC serial port.
Register / Bit Settings
Description
Functional Mode Register (addr = 03h)
Set DAC_FMx = 00,01,10
DAC_LRCK can run at SSM, DSM, or QSM independent of ADC_LRCK
Set ADC_FMx = 00,01,10
ADC_LRCK can run at SSM, DSM, or QSM independent of DAC_LRCK
Set ADC_CLK_SEL = 1
Configure ADC_SDOUT to be clocked from the ADC_SP clocks.
Interface Format Register (addr = 04h)
Set DIFx bits to proper serial format
Select the digital interface format when not in one line mode
Set ADC_OLx bits = 00,01
Select ADC operating mode, see table below for valid combinations
Set DAC_OLx bits = 00,01,10
Select DAC operating mode, see table below for valid combinations
Misc. Control Register (addr = 05h)
Set DAC_SP M/S = 1
Set DAC Serial Port to master mode.
Set ADC_SP M/S = 0 or 1
Set ADC Serial Port to master mode or slave mode.
Set EXT ADC SCLK = 0
Identify external ADC clock source as ADC Serial Port.
DAC Mode
Not One Line Mode
ADC Mode
One Line Mode #1
One Line Mode #2
Not One
Line Mode
DAC_SCLK=64Fs
DAC_LRCK=SSM/DSM/QSM
ADC_SCLK=64Fs
ADC_LRCK=SSM/DSM/QSM
DAC_SCLK=128Fs
DAC_LRCK=SSM/DSM
ADC_SCLK=64Fs
ADC_LRCK=SSM/DSM/QSM
DAC_SCLK=256Fs
DAC_LRCK=SSM
ADC_SCLK=64Fs
ADC_LRCK=SSM/DSM/QSM
One Line
Mode #1
DAC_SCLK=64Fs
DAC_LRCK=SSM/DSM/QSM
ADC_SCLK=128Fs
ADC_LRCK=SSM
DAC_SCLK=128Fs
DAC_LRCK=SSM/DSM
ADC_SCLK=128Fs
ADC_LRCK=SSM
DAC_SCLK=256Fs
DAC_LRCK=SSM
ADC_SCLK=128Fs
ADC_LRCK=SSM
One Line
Mode #2
not valid
not valid
not valid
MC LK
64Fs,128Fs
LRC K
ADC_SCLK
SCLK
AD C_LRCK
MCLK
RMCK
SDO UT1
ADCIN1
SDO UT2
ADCIN2
SCLK_PO RT1
LRCK_PO RT1
SDIN_PORT1
ADC_SDO UT
CS5361
CS5361
64Fs,128Fs,256Fs
DAC _SCLK
SCLK _PO RT2
D AC_LRCK
LRCK_P ORT2
DAC_SDIN1
SDO UT1_POR T2
DAC_SDIN2
SDO UT2_POR T2
DAC_SDIN3
SDO UT3_POR T2
CS42426
Figure 15. OLM Configuration #3
24
DIGITA L A UDIO
PROCESSOR
CS42426
3.5.4.4
OLM Config #4
This One-Line Mode configuration can support up to 6 channels of DAC data on 2 DAC_SDIN pins, and
2 channels of ADC data and will handle up to 24-bit samples at a sampling frequency of 48 kHz on all
channels for both the DAC and ADC. The output data stream of the internal ADCs can be configured to
run at the DAC_SP clock speeds or to run at the ADC_SP rate. The DAC_SP and ADC_SP can operate at
different Fs rates.
Register / Bit Settings
Description
Functional Mode Register (addr = 03h)
Set DAC_FMx = 00,01,10
DAC_LRCK can run at SSM, DSM, or QSM independent of ADC_LRCK
Set ADC_FMx = 00,01,10
ADC_LRCK can run at SSM, DSM, or QSM independent of DAC_LRCK
Configure ADC_SDOUT to be clocked from the ADC_SP or DAC_SP
clocks.
Set ADC_CLK_SEL = 0 or 1
Interface Format Register (addr = 04h)
Set DIFx bits to proper serial format
Select the digital interface format when not in one line mode
Set ADC operating mode to Not One Line Mode since only 2 channels of
ADC are supported
Set ADC_OLx bits = 00
Set DAC_OLx bits = 00,01,10
Select DAC operating mode, see table below for valid combinations
Misc. Control Register (addr = 05h)
Set DAC_SP M/S = 0 or 1
Set DAC Serial Port to master mode or slave mode.
Set ADC_SP M/S = 0 or 1
Set ADC Serial Port to master mode or slave mode.
Set EXT ADC SCLK = 0
External ADCs are not used. Leave bit in default state.
DAC Mode
Not One Line Mode
Not One
Line Mode
ADC Mode
DAC_SCLK=64Fs/128Fs
DAC_LRCK=SSM/DSM/QSM
ADC_SCLK=64Fs/128Fs
ADC_LRCK=SSM/DSM/QSM
One Line Mode #1
DAC_SCLK=128Fs
DAC_LRCK=SSM/DSM
ADC_SCLK=64Fs/128Fs
ADC_LRCK=SSM/DSM/QSM
One Line Mode #2
DAC_SCLK=256Fs
DAC_LRCK=SSM
ADC_SCLK=64Fs/128Fs
ADC_LRCK=SSM/DSM/QSM
One Line
Mode #1
not valid
not valid
not valid
One Line
Mode #2
not valid
not valid
not valid
MCLK
64Fs ,12 8Fs
S CLK_P ORT1
A DC_SCLK
LRCK _PORT1
A DC_LRCK
RMCK
S DIN_PORT1
A DC_SDOUT
A DCIN1
A DCIN2
S DIN_PORT2
64 Fs,128Fs, 256Fs
DA C_S CLK
SCLK_PORT2
DAC_LRCK
LRCK _P ORT2
DAC_SDIN1
DAC_SDIN2
S DO UT1_PORT2
DAC_SDIN3
S DO UT3_PORT2
CS42426
S DO UT2_PORT2
DIG ITAL AUDIO
P RO CESS OR
Figure 16. OLM Configuration #4
25
CS42426
3.6
Control Port Description and Timing
The control port is used to access the registers, allowing the CS42426 to be configured for the desired operational modes and formats. The operation of the control port may be completely asynchronous with respect to the audio sample rates. However, to avoid potential interference problems, the control port pins
should remain static if no operation is required.
The control port has 2 modes: SPI and I2C, with the CS42426 acting as a slave device. SPI mode is selected
if there is a high to low transition on the AD0/CS pin, after the RST pin has been brought high. I2C mode
is selected by connecting the AD0/CS pin through a resistor to VLC or DGND, thereby permanently selecting the desired AD0 bit address state.
3.6.1
SPI Mode
In SPI mode, CS is the CS42426 chip select signal, CCLK is the control port bit clock (input into the
CS42426 from the microcontroller), CDIN is the input data line from the microcontroller, CDOUT is the
output data line to the microcontroller. Data is clocked in on the rising edge of CCLK and out on the falling
edge.
Figure 17 shows the operation of the control port in SPI mode. To write to a register, bring CS low. The
first seven bits on CDIN form the chip address and must be 1001111. The eighth bit is a read/write indicator (R/W), which should be low to write. The next eight bits form the Memory Address Pointer (MAP),
which is set to the address of the register that is to be updated. The next eight bits are the data which will
be placed into the register designated by the MAP. During writes, the CDOUT output stays in the Hi-Z
state. It may be externally pulled high or low with a 47 kΩ resistor, if desired.
There is a MAP auto increment capability, enabled by the INCR bit in the MAP register. If INCR is a zero,
the MAP will stay constant for successive read or writes. If INCR is set to a 1, the MAP will autoincrement
after each byte is read or written, allowing block reads or writes of successive registers.
To read a register, the MAP has to be set to the correct address by executing a partial write cycle which
finishes (CS high) immediately after the MAP byte. The MAP auto increment bit (INCR) may be set or
CS
CCLK
C H IP
ADDRESS
C D IN
1001111
M AP
MSB
R/W
C H IP
AD D R ESS
DATA
b y te 1
LSB
1001111
R/W
b y te n
High Impedance
CD OUT
MAP = Memory Address Pointer, 8 bits, MSB first
Figure 17. Control Port Timing in SPI Mode
26
MSB
LSB MSB
LSB
CS42426
not, as desired. To begin a read, bring CS low, send out the chip address and set the read/write bit (R/W)
high. The next falling edge of CCLK will clock out the MSB of the addressed register (CDOUT will leave
the high impedance state). If the MAP auto increment bit is set to 1, the data for successive registers will
appear consecutively.
I2C Mode
3.6.2
In I2C mode, SDA is a bidirectional data line. Data is clocked into and out of the part by the clock, SCL.
There is no CS pin. Pins AD0 and AD1 form the two least significant bits of the chip address and should
be connected through a resistor to VLC or DGND as desired. The state of the pins is sensed while the
CS42426 is being reset.
The signal timings for a read and write cycle are shown in Figure 18 and Figure 19. A Start condition is
defined as a falling transition of SDA while the clock is high. A Stop condition is a rising transition while
the clock is high. All other transitions of SDA occur while the clock is low. The first byte sent to the
CS42426 after a Start condition consists of a 7 bit chip address field and a R/W bit (high for a read, low
for a write). The upper 5 bits of the 7-bit address field are fixed at 10011. To communicate with a CS42426,
the chip address field, which is the first byte sent to the CS42426, should match 10011 followed by the
settings of the AD1 and AD0. The eighth bit of the address is the R/W bit. If the operation is a write, the
next byte is the Memory Address Pointer (MAP) which selects the register to be read or written. If the operation is a read, the contents of the register pointed to by the MAP will be output. Setting the auto increment bit in MAP allows successive reads or writes of consecutive registers. Each byte is separated by an
acknowledge bit. The ACK bit is output from the CS42426 after each input byte is read, and is input to the
CS42426 from the microcontroller after each transmitted byte.
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18
24 25 26 27 28
19
SCL
CHIP ADDRESS (WRITE)
1
SDA
0
0
1
MAP BYTE
1 AD1 AD0 0
INCR
6
5
4
3
DATA
2
1
0
ACK
7
6
1
ACK
DATA +1
0
7
6
1
DATA +n
0
7
6
1
0
ACK
ACK
STOP
START
Figure 18. Control Port Timing, I2C Slave Mode Write
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16
17 18
19
20 21 22 23 24 25 26 27 28
SCL
CHIP ADDRESS (WRITE)
SDA
1
0
0
1
1 AD1 AD0 0
INCR
ACK
START
STOP
MAP BYTE
6
5
4
3
2
1
CHIP ADDRESS (READ)
1
0
ACK
0
0
1
DATA
1 AD1 AD0 1
7
ACK
START
DATA +1
0
7
ACK
0
DATA + n
7
0
NO
ACK
STOP
Figure 19. Control Port Timing, I2C Slave Mode Read
27
CS42426
Since the read operation can not set the MAP, an aborted write operation is used as a preamble. As shown
in Figure 19, the write operation is aborted after the acknowledge for the MAP byte by sending a stop condition. The following pseudocode illustrates an aborted write operation followed by a read operation.
Send start condition.
Send 10011xx0 (chip address & write operation).
Receive acknowledge bit.
Send MAP byte, auto increment off.
Receive acknowledge bit.
Send stop condition, aborting write.
Send start condition.
Send 10011xx1(chip address & read operation).
Receive acknowledge bit.
Receive byte, contents of selected register.
Send acknowledge bit.
Send stop condition.
Setting the auto increment bit in the MAP allows successive reads or writes of consecutive registers. Each
byte is separated by an acknowledge bit.
3.7
Interrupts
The CS42426 has a comprehensive interrupt capability. The INT output pin is intended to drive the interrupt input pin on the host microcontroller. The INT pin may be set to be active low, active high or active
low with no active pull-up transistor. This last mode is used for active low, wired-OR hook-ups, with multiple peripherals connected to the microcontroller interrupt input pin.
Many conditions can cause an interrupt, as listed in the interrupt status register descriptions. See “Interrupt
Status (address 20h) (Read Only)” on page 46. Each source may be masked off through mask register bits.
In addition, each source may be set to rising edge, falling edge, or level sensitive. Combined with the option of level sensitive or edge sensitive modes within the microcontroller, many different configurations
are possible, depending on the needs of the equipment designer.
28
CS42426
3.8
Reset and Power-up
Reliable power-up can be accomplished by keeping the device in reset until the power supplies, clocks and
configuration pins are stable. It is also recommended that reset be activated if the analog or digital supplies
drop below the recommended operating condition to prevent power glitch related issues.
When RST is low, the CS42426 enters a low power mode and all internal states are reset, including the
control port and registers, and the outputs are muted. When RST is high, the control port becomes operational and the desired settings should be loaded into the control registers. Writing a 0 to the PDN bit in the
Power Control Register will then cause the part to leave the low power state and begin operation. If the
internal PLL is selected as the clock source, the serial audio outputs will be enabled after the PLL has settled. See “Power Control (address 02h)” on page 33 for more details.
The delta-sigma modulators settle in a matter of microseconds after the analog section is powered, either
through the application of power or by setting the RST pin high. However, the voltage reference will take
much longer to reach a final value due to the presence of external capacitance on the FILT+ pin. A time
delay of approximately 80ms is required after applying power to the device or after exiting a reset state.
During this voltage reference ramp delay, all serial ports and DAC outputs will be automatically muted.
3.9
Power Supply, Grounding, and PCB layout
As with any high resolution converter, the CS42426 requires careful attention to power supply and grounding arrangements if its potential performance is to be realized. Figure 1 shows the recommended power
arrangements, with VA connected to clean supplies. VD, which powers the digital circuitry, may be run
from the system logic supply. Alternatively, VD may be powered from the analog supply via a ferrite bead.
In this case, no additional devices should be powered from VD.
For applications where the output of the PLL is required to be low jitter, use a separate, low noise analog
+5 V supply for VA, decoupled to AGND. In addition, a separate region of analog ground plane around
the FILT+, VQ, LPFLT, REFGND, AGND, and VA pins is recommended.
Extensive use of power and ground planes, ground plane fill in unused areas and surface mount decoupling
capacitors are recommended. Decoupling capacitors should be as near to the pins of the CS42426 as possible. The low value ceramic capacitor should be the nearest to the pin and should be mounted on the same
side of the board as the CS42426 to minimize inductance effects. All signals, especially clocks, should be
kept away from the FILT+, VQ and LPFLT pins in order to avoid unwanted coupling into the modulators
and PLL. The FILT+ and VQ decoupling capacitors, particularly the 0.1 µF, must be positioned to minimize the electrical path from FILT+ and REFGND. The CDB42418 evaluation board demonstrates the optimum layout and power supply arrangements.
29
CS42426
4 REGISTER QUICK REFERENCE
Addr
01h
Function
ID
default
02h
Power Control
default
03h
Functional Mode
default
04h
Interface Formats
default
05h
Misc Control
06h
Clock Control
07h
OMCK/PLL_CLK
Ratio
08h
Clock Status
default
default
default
default
09h0Ch
Reserved
default
0Dh
Volume Control
default
0Eh
Channel Mute
default
0Fh
Vol. Control A1
default
10h
Vol. Control B1
default
11h
Vol. Control A2
default
12h
Vol. Control B2
default
13h
Vol. Control A3
default
14h
Vol. Control B3
default
15h
Reserved
default
16h
Reserved
default
17h
Channel Invert
default
18h
Mixing Ctrl Pair 1
default
30
7
6
5
4
3
2
1
0
Chip_ID3
Chip_ID2
Chip_ID1
CHIP_ID0
Rev_ID3
Rev_ID2
Rev_ID1
Rev_ID0
1
1
1
0
0
0
1
Reserved
PDN_PLL
PDN_ADC
Reserved
0
0
0
0
0
0
0
1
DAC_FM1
DAC_FM0
ADC_FM1
ADC_FM0
Reserved
ADC_CLK
SEL
DAC_DEM
Reserved
0
0
0
0
0
0
0
0
DIF1
DIF0
ADC_OL1
ADC_OL0
DAC_OL1
DAC_OL0
Reserved
CODEC_RJ16
0
1
0
0
0
0
0
0
Ext ADC
SCLK
HiZ_RMCK
Reserved
FREEZE
FILTSEL
HPF_
FREEZE
DAC_SP
M/S
ADC_SP
M/S
0
0
0
1
1
RMCK_DIV1 RMCK_DIV0
PDN_DAC3 PDN_DAC2 PDN_DAC1
0
0
0
OMCK
Freq1
OMCK
Freq0
PLL_LRCK
1
PDN
SW_CTRL1 SW_CTRL0 FRC_PLL_LK
0
0
0
0
0
0
1
0
RATIO7
RATIO6
RATIO5
RATIO4
RATIO3
RATIO2
RATIO1
RATIO0
X
X
X
X
X
X
X
X
Reserved
Reserved
Reserved
Reserved
Active_CLK
PLL_CLK2
PLL_CLK1
PLL_CLK0
X
X
X
X
X
X
X
X
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
X
X
X
X
X
X
X
X
Reserved
SNGVOL
SZC1
SZC0
AMUTE
Reserved
RAMP_UP
RAMP_DN
0
0
0
0
1
0
0
0
Reserved
Reserved
B3_MUTE
A3_MUTE
B2_MUTE
A2_MUTE
B1_MUTE
A1_MUTE
0
0
0
0
0
0
0
0
A1_VOL7
A1_VOL6
A1_VOL5
A1_VOL4
A1_VOL3
A1_VOL2
A1_VOL1
A1_VOL0
0
0
0
0
0
0
0
0
B1_VOL7
B1_VOL6
B1_VOL5
B1_VOL4
B1_VOL3
B1_VOL2
B1_VOL1
B1_VOL0
0
0
0
0
0
0
0
0
A2_VOL7
A2_VOL6
A2_VOL5
A2_VOL4
A2_VOL3
A2_VOL2
A2_VOL1
A2_VOL0
0
0
0
0
0
0
0
0
B2_VOL7
B2_VOL6
B2_VOL5
B2_VOL4
B2_VOL3
B2_VOL2
B2_VOL1
B2_VOL0
0
0
0
0
0
0
0
0
A3_VOL7
A3_VOL6
A3_VOL5
A3_VOL4
A3_VOL3
A3_VOL2
A3_VOL1
A3_VOL0
0
0
0
0
0
0
0
0
B3_VOL7
B3_VOL6
B3_VOL5
B3_VOL4
B3_VOL3
B3_VOL2
B3_VOL1
B3_VOL0
0
0
0
0
0
0
0
0
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
0
0
0
0
0
0
0
0
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
0
0
0
0
0
0
0
0
Reserved
Reserved
INV_B3
INV_A3
INV_B2
INV_A2
INV_B1
INV_A1
0
0
0
0
0
0
0
0
P1_A=B
Reserved
Reserved
P1_ATAPI4
P1_ATAPI3
P1_ATAPI2
P1_ATAPI1
P1_ATAPI0
0
0
0
0
1
0
0
1
CS42426
Addr
Function
7
6
5
4
3
2
1
0
19h
Mixing Ctrl Pair 2
P2_A=B
Reserved
Reserved
P2_ATAPI4
P2_ATAPI3
P2_ATAPI2
P2_ATAPI1
P2_ATAPI0
0
0
0
0
1
0
0
1
P3_A=B
Reserved
Reserved
P3_ATAPI4
P3_ATAPI3
P3_ATAPI2
P3_ATAPI1
P3_ATAPI0
0
0
0
0
1
0
0
1
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
0
0
0
0
1
0
0
1
Reserved
Reserved
LGAIN5
LGAIN4
LGAIN3
LGAIN2
LGAIN1
LGAIN0
0
0
0
0
0
0
0
0
Reserved
Reserved
RGAIN5
RGAIN4
RGAIN3
RGAIN2
RGAIN1
RGAIN0
0
0
0
0
0
0
0
0
SP_SYNC
Reserved
INT1
INT0
Reserved
Reserved
0
0
0
0
0
0
0
0
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
0
0
0
0
0
0
0
0
UNLOCK
Reserved
Reserved
Reserved
Reserved
Reserved
OverFlow
Reserved
X
X
X
X
X
X
X
X
UNLOCKM
Reserved
Reserved
Reserved
Reserved
Reserved
OverFlowM
Reserved
0
0
0
0
0
0
0
0
UNLOCK1
Reserved
Reserved
Reserved
Reserved
Reserved
OF1
Reserved
0
0
0
0
0
0
0
0
UNLOCK0
Reserved
Reserved
Reserved
Reserved
Reserved
OF0
Reserved
0
0
0
0
0
0
0
0
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
0
0
0
0
0
0
0
0
Reserved
Reserved
MCPolarity
0
0
0
1
1
1
1
1
Mode1
Mode0
Polarity
Function4
Function3
Function2
Function1
Function0
0
0
0
0
0
0
0
0
Mode1
Mode0
Polarity
Function4
Function3
Function2
Function1
Function0
0
0
0
0
0
0
0
0
Mode1
Mode0
Polarity
Function4
Function3
Function2
Function1
Function0
0
0
0
0
0
0
0
0
Mode1
Mode0
Polarity
Function4
Function3
Function2
Function1
Function0
0
0
0
0
0
0
0
0
Mode1
Mode0
Polarity
Function4
Function3
Function2
Function1
Function0
0
0
0
0
0
0
0
0
Mode1
Mode0
Polarity
Function4
Function3
Function2
Function1
Function0
0
0
0
0
0
0
0
0
Mode1
Mode0
Polarity
Function4
Function3
Function2
Function1
Function0
0
0
0
0
0
0
0
0
default
1Ah
Mixing Ctrl Pair 3
default
1Bh
Reserved
default
1Ch
ADC Left Ch.
Gain
default
1Dh
ADC Right Ch.
Gain
default
1Eh
Interrupt Control
default
1Fh
Reserved
default
20h
Interrupt Status
default
21h
Interrupt Mask
default
22h
Interrupt Mode
MSB
default
23h
Interrupt Mode
LSB
default
24h27h
Reserved
default
28h
MUTEC
default
29h
GPO7
default
2Ah
GPO6
default
2Bh
GPO5
default
2Ch
GPO4
default
2Dh
GPO3
default
2Eh
GPO2
default
2Fh
GPO1
default
DE-EMPH1 DE-EMPH0
M_AOUTA1 M_AOUTB1 M_AOUTA2 M_AOUTA3
M_AOUTB2 M_AOUTB3
Reserved
31
CS42426
5 REGISTER DESCRIPTION
All registers are read/write except for I.D. and Revision Register, OMCK/PLL_CLK Ratio Register, Clock
Status and Interrupt Status Register which are read only. See the following bit definition tables for bit assignment information. The default state of each bit after a power-up sequence or reset is listed in each bit
description.
5.1
Memory Address Pointer (MAP)
Not a register
7
6
5
4
3
2
1
0
INCR
MAP6
MAP5
MAP4
MAP3
MAP2
MAP1
MAP0
5.1.1
INCREMENT(INCR)
Default = 1
Function:
Memory address pointer auto increment control
0 - MAP is not incremented automatically.
1 - Internal MAP is automatically incremented after each read or write.
5.1.2
MEMORY ADDRESS POINTER (MAPX)
Default = 0000001
Function:
Memory address pointer (MAP). Sets the register address that will be read or written by the control
port.
5.2
Chip I.D. and Revision Register (address 01h) (Read Only)
7
Chip_ID3
5.2.1
6
Chip_ID2
5
Chip_ID1
4
CHIP_ID0
3
Rev_ID3
CHIP I.D. (CHIP_IDX)
Default = 1110
Function:
I.D. code for the CS42426. Permanently set to 1110.
5.2.2
CHIP REVISION (REV_IDX)
Default = 0001
Function:
CS42426 revision level. Revision C is coded as 0011.
32
2
Rev_ID2
1
Rev_ID1
0
Rev_ID0
CS42426
5.3
Power Control (address 02h)
7
6
5
4
3
2
1
0
Reserved
PDN_PLL
PDN_ADC
Reserved
PDN_DAC3
PDN_DAC2
PDN_DAC1
PDN
5.3.1
POWER DOWN PLL (PDN_PLL)
Default = 0
Function:
When enabled, the PLL will remain in a reset state. It is advised that any change of this bit be made
while the DACs are muted or the power down bit (PDN) is enabled to eliminate the possibility of audible artifacts.
5.3.2
POWER DOWN ADC (PDN_ADC)
Default = 0
Function:
When enabled the stereo analog to digital converter will remain in a reset state. It is advised that any
change of this bit be made while the DACs are muted or the power down bit (PDN) is enabled to eliminate the possibility of audible artifacts.
5.3.3
POWER DOWN DAC PAIRS (PDN_DACX)
Default = 0
Function:
When enabled the respective DAC channel pair x (AOUTAx and AOUTBx) will remain in a reset state.
5.3.4
POWER DOWN (PDN)
Default = 1
Function:
The entire device will enter a low-power state when this function is enabled, and the contents of the
control registers are retained in this mode. The power down bit defaults to ‘enabled’ on power-up and
must be disabled before normal operation can occur.
5.4
Functional Mode (address 03h)
7
6
5
4
3
2
1
0
DAC_FM1
DAC_FM0
ADC_FM1
ADC_FM0
Reserved
ADC_SP SEL
DAC_DEM
Reserved
5.4.1
DAC FUNCTIONAL MODE (DAC_FMX)
Default = 00
00 - Single-Speed Mode (4 to 50 kHz sample rates)
01 - Double-Speed Mode (50 to 100 kHz sample rates)
10 - Quad-Speed Mode (100 to 192 kHz sample rates)
11 - Reserved
Function:
Selects the required range of sample rates for all converters clocked from the DAC serial port (DAC_SP).
Bits must be set to the corresponding sample rate range when the DAC_SP is in Master or Slave mode.
33
CS42426
5.4.2
ADC FUNCTIONAL MODE (ADC_FMX)
Default = 00
00 - Single-Speed Mode (4 to 50 kHz sample rates)
01 - Double-Speed Mode (50 to 100 kHz sample rates)
10 - Quad-Speed Mode (100 to 192 kHz sample rates)
11 - Reserved
Function:
Selects the required range of sample rates for the ADC serial port(ADC_SP). These bits must be set
to the corresponding sample rate range when the ADC_SP is in Master or Slave mode.
5.4.3
ADC CLOCK SOURCE SELECT (ADC_CLK SEL)
Default = 0
0 - ADC_SDOUT clocked from the DAC_SP.
1 - ADC_SDOUT clocked from the ADC_SP.
Function:
Selects the desired clocks for the ADC serial output.
5.4.4
DAC DE-EMPHASIS CONTROL (DAC_DEM)
Default = 0
Function:
Enables the digital filter to maintain the standard 15 µs/50 µs digital de-emphasis filter response at
the auto-detected sample rate of either 32, 44.1, or 48 kHz. De-emphasis will not be enabled, regardless of this register setting, at any other sample rate. If the FRC_PLL_LK bit is set to a ‘1’b, then the
auto-detect sample rate feature is disabled. To apply the correct de-emphasis filter, use the DEEMPH bits in the Interrupt Control (address 1Eh) register to set the appropriate sample rate.
DAC_DEM
reg03h[1]
FRC_PLL_LK
reg06h[0]
DE-EMPH[1:0]
reg1Eh[5:4]
De-Emphasis
Mode
0
1
1
X
0
1
XX
XX
00
01
10
11
No De-Emphasis
Auto-Detect Fs
Reserved
32 kHz
44.1 kHz
48 kHz
Table 6. DAC De-Emphasis
5.5
Interface Formats (address 04h)
7
6
5
4
3
2
1
0
DIF1
DIF0
ADC_OL1
ADC_OL0
DAC_OL1
DAC_OL0
Reserved
CODEC_RJ16
5.5.1
DIGITAL INTERFACE FORMAT (DIFX)
Default = 01
Function:
These bits select the digital interface format used for the ADC & DAC Serial Port when not in one_line
mode. The required relationship between the Left/Right clock, serial clock and serial data is defined by
the Digital Interface Format and the options are detailed in Figures 7 - 9.
34
CS42426
DIF1
DIF0
0
0
1
1
0
1
0
1
Description
Left Justified, up to 24-bit data
I2S, up to 24-bit data
Right Justified, 16-bit or 24-bit data
reserved
Format
Figure
0
1
2
-
9
8
7
-
Table 7. Digital Interface Formats
5.5.2
ADC ONE_LINE MODE (ADC_OLX)
Default = 00
Function:
These bits select which mode the ADC will use. By default one-line mode is disabled but can be selected using these bits. Please see Figures 10 and 11 to see the format of one-line mode 1 and
one-line mode 2.
ADC_OL1
ADC_OL2
0
0
1
1
0
1
0
1
Description
DIF: take the DIF setting from reg04h[7:6]
One-Line #1
One-Line #2
reserved
Format
Figure
3
4
-
10
11
-
Table 8. ADC One_Line Mode
5.5.3
DAC ONE_LINE MODE (DAC_OLX)
Default = 00
Function:
These bits select which mode the DAC will use. By default one-line mode is disabled but can be selected using these bits. Please see Figures 10 and 11 to see the format of one-line mode 1 and
one-line mode 2.
DAC_OL1
DAC_OL2
0
0
1
1
0
1
0
1
Description
DIF: take the DIF setting from reg04h[7:6]
One-Line #1
One-Line #2
reserved
Format
Figure
3
4
-
10
11
-
Table 9. DAC One_Line Mode
5.5.4
CODEC RIGHT JUSTIFIED BITS (CODEC_RJ16)
Default = 0
Function:
This bit determines how many bits to use during right justified mode for the DAC and ADC. By default
the DAC and ADC will be in RJ24 bits but can be set to RJ16 bits.
0 - 24 bit mode.
1 - 16 bit mode.
35
CS42426
5.6
Misc Control (address 05h)
7
6
5
4
3
2
1
0
Ext ADC SCLK
HiZ_RMCK
Reserved
FREEZE
FILT_SEL
HPF_FREEZE
DAC_SP
M/S
ADC_SP
M/S
5.6.1
EXTERNAL ADC SCLK SELECT (EXT ADC SCLK)
Default = 0
Function:
This bit identifies the SCLK source for the external ADCs attached to the ADCIN1/2 ports when using
one line mode of operation.
0 - ADC_SCLK is used as external ADC SCLK.
1 - DAC_SCLK is used as external ADC SCLK.
5.6.2
RMCK HIGH IMPEDANCE (HIZ_RMCK)
Default = 0
Function:
This bit is used to create a high impedance output on RMCK when the clock signal is not required.
5.6.3
FREEZE CONTROLS (FREEZE)
Default = 0
Function:
This function will freeze the previous output of, and allow modifications to be made, to the Volume
Control (address 0Fh-16h), Channel Invert (address 17h) and Mixing Control Pair (address 18h-1Bh)
registers without the changes taking effect until the FREEZE is disabled. To make multiple changes
in these control port registers take effect simultaneously, enable the FREEZE bit, make all register
changes, then disable the FREEZE bit.
5.6.4
INTERPOLATION FILTER SELECT (FILT_SEL)
Default = 0
Function:
This feature allows the user to select whether the DAC interpolation filter has a fast or slow roll off.
For filter characteristics please See “D/A Digital Filter Characteristics” on page 56.
0 - Fast roll off.
1 - Slow roll off.
5.6.5
HIGH PASS FILTER FREEZE (HPF_FREEZE)
Default = 0
Function:
When this bit is set, the internal high-pass filter for the selected channel will be disabled.The current
DC offset value will be frozen and continue to be subtracted from the conversion result. See “A/D Digital Filter Characteristics” on page 52.
36
CS42426
5.6.6
DAC SERIAL PORT MASTER/SLAVE SELECT (DAC_SP M/S)
Default = 1
Function:
In Master mode, DAC_SCLK and DAC_LRCK are outputs. Internal dividers will divide the master
clock to generate the serial clock and left/right clock. In Slave mode, DAC_SCLK and DAC_LRCK
become inputs.
5.6.7
ADC SERIAL PORT MASTER/SLAVE SELECT (ADC_SP M/S)
Default = 1
Function:
In Master mode, ADC_SCLK and ADC_LRCK are outputs. Internal dividers will divide the master
clock to generate the serial clock and left/right clock. In Slave mode, ADC_SCLK and ADC_LRCK
become inputs.
To use the PLL to lock to ADC_LRCK, the ADC_SP must be in slave mode. When using the PLL to
lock to LRCK, if ADC_SDOUT is configured to be clocked by the ADC_SP, then both ADC_SCLK and
ADC_LRCK must be present. If ADC_SDOUT is configured to be clocked by the DAC_SP, then only
the ADC_LRCK signal must be applied.
5.7
Clock Control (address 06h)
7
6
5
4
3
2
1
0
RMCK_DIV1
RMCK_DIV0
OMCK Freq1
OMCK Freq0
PLL_LRCK
SW_CTRL1
SW_CTRL0
FRC_PLL_LK
5.7.1
RMCK DIVIDE (RMCK_DIVX)
Default = 00
Function:
Divides/multiplies the internal MCLK, either from the PLL or OMCK, by the selected factor.
RMCK_DIV1 RMCK_DIV0
0
0
1
1
0
1
0
1
Description
Divide by 1
Divide by 2
Divide by 4
Multiply by 2
Table 10. RMCK Divider Settings
37
CS42426
5.7.2
OMCK FREQUENCY (OMCK FREQX)
Default = 00
Function:
Sets the appropriate frequency for the supplied OMCK.
OMCK Freq1 OMCK Freq0 Description
0
0
11.2896 MHz or 12.2880 MHz
0
1
16.9344 MHz or 18.4320 MHz
1
0
22.5792 MHz or 24.5760 MHz
1
1
Reserved
Table 11. OMCK Frequency Settings
5.7.3
PLL LOCK TO LRCK (PLL_LRCK)
Default = 0
0 - Disabled
1 - Enabled
Function:
When enabled, the internal PLL of the CS42426 will lock to the LRCK of the ADC serial port
(ADC_LRCK) while the ADC_SP is in slave mode.
5.7.4
MASTER CLOCK SOURCE SELECT (SW_CTRLX)
Default = 01
Function:
These two bits, along with the UNLOCK bit in register “Interrupt Status (address 20h) (Read Only)”
on page 46, determine the master clock source for the CS42426. When SW_CTRL1 and SW_CTRL0
are set to '00'b, selecting the output of the PLL as the internal clock source, and the PLL becomes
unlocked, then RMCK will equal OMCK, but all internal and serial port timings are not valid.
SW_CTRL1 SW_CTRL0
UNLOCK
0
0
1
0
1
0
X
X
0
1
1
1
0
1
Description
Manual setting, MCLK sourced from PLL.
Manual setting, MCLK sourced from OMCK.
Hold, keep same MCLK source.
Auto switch, MCLK sourced from OMCK.
Auto switch, MCLK sourced from PLL.
Auto switch, MCLK sourced from OMCK.
Table 12. Master Clock Source Select
5.7.5
FORCE PLL LOCK (FRC_PLL_LK)
Default = 0
Function:
This bit is used to enable the PLL to lock to the ADC_LRCK with the absence of a clock signal on
OMCK. When set to a ‘1’b, the auto-detect sample frequency feature will be disabled. The OMCK/PLL_CLK Ratio (address 07h) (Read Only) register contents are not valid and the PLL_CLK[2:0]
bits will be set to ‘111’b. Use the DE-EMPH[1:0] bits to properly apply de-emphasis filtering.
38
CS42426
5.8
OMCK/PLL_CLK Ratio (address 07h) (Read Only)
7
6
5
4
3
2
1
0
RATIO7(21)
RATIO6(20)
RATIO5(2-1)
RATIO4(2-2)
RATIO3(2-3)
RATIO2(2-4)
RATIO1(2-5)
RATIO0(2-6)
5.8.1
OMCK/PLL_CLK RATIO (RATIOX)
Default = sixth
Function:
This register allows the user to find the exact absolute frequency of the recovered MCLK coming from
the PLL. This value is represented as an integer (RATIO7:6) and a fractional (RATIO5:0) part. For
example, an OMCK/PLL_CLK ratio of 1.5 would be displayed as 60h.
5.9
Clock Status (address 08h) (Read Only)
7
6
5
4
3
2
1
0
Reserved
Reserved
Reserved
Reserved
Active_CLK
PLL_CLK2
PLL_CLK1
PLL_CLK0
5.9.1
SYSTEM CLOCK SELECTION (ACTIVE_CLK)
Default = x
0 - Output of PLL
1 - OMCK
Function:
This bit identifies the source of the internal system clock (MCLK).
5.9.2
PLL CLOCK FREQUENCY (PLL_CLKX)
Default = xxxh
Function:
The CS42426 will auto-detect the ratio between the OMCK and the recovered clock from the PLL,
which is displayed in register 07h. Based on this ratio, the absolute frequency of the PLL clock can
be determined, and this information is displayed according to the following table. If the absolute frequency of the PLL clock does not match one of the given frequencies, this register will display the
closest available value.
NOTE: These bits are set to ‘111’b when the FRC_PLL_LK bit is ‘1’b.
PLL_CLK2
PLL_CLK1
PLL_CLK0
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
Description
8.1920 MHz
11.2896 MHz
12.288 MHz
16.3840 MHz
22.5792 MHz
24.5760 MHz
45.1584 MHz
49.1520 MHz
Table 13. PLL Clock Frequency Detection
39
CS42426
5.10
Volume Control (address 0Dh)
7
6
5
4
3
2
1
0
Reserved
SNGVOL
SZC1
SZC0
AMUTE
MUTE ADC_SP
RAMP_UP
RAMP_DN
5.10.1 SINGLE VOLUME CONTROL (SNGVOL)
Default = 0
Function:
The individual channel volume levels are independently controlled by their respective Volume Control
registers when this function is disabled. When enabled, the volume on all channels is determined by
the A1 Channel Volume Control register and the other Volume Control registers are ignored.
5.10.2 SOFT RAMP AND ZERO CROSS CONTROL (SZCX)
Default = 00
00 - Immediate Change
01 - Zero Cross
10 - Soft Ramp
11 - Soft Ramp on Zero Crossings
Function:
Immediate Change
When Immediate Change is selected all level changes will take effect immediately in one step.
Zero Cross
Zero Cross Enable dictates that signal level changes, either by attenuation changes or muting, will
occur on a signal zero crossing to minimize audible artifacts. The requested level change will occur
after a timeout period between 512 and 1024 sample periods (10.7 ms to 21.3 ms at 48 kHz sample
rate) if the signal does not encounter a zero crossing. The zero cross function is independently monitored and implemented for each channel.
Soft Ramp
Soft Ramp allows level changes, both muting and attenuation, to be implemented by incrementally
ramping, in 1/8 dB steps, from the current level to the new level at a rate of 1 dB per 8 left/right clock
periods.
Soft Ramp on Zero Crossing
Soft Ramp and Zero Cross Enable dictates that signal level changes, either by attenuation changes
or muting, will occur in 1/8 dB steps and be implemented on a signal zero crossing. The 1/8 dB level
change will occur after a timeout period between 512 and 1024 sample periods (10.7 ms to 21.3 ms
at 48 kHz sample rate) if the signal does not encounter a zero crossing. The zero cross function is
independently monitored and implemented for each channel.
5.10.3 AUTO-MUTE (AMUTE)
Default = 1
0 - Disabled
1 - Enabled
Function:
40
CS42426
The Digital-to-Analog converters of the CS42426 will mute the output following the reception of 8192
consecutive audio samples of static 0 or -1. A single sample of non-static data will release the mute.
Detection and muting is done independently for each channel. The quiescent voltage on the output
will be retained and the MUTEC pin will go active during the mute period. The muting function is affected, similar to volume control changes, by the Soft and Zero Cross bits (SZC[1:0]).
5.10.4 SOFT VOLUME RAMP-UP AFTER ERROR (RMP_UP)
Default = 0
0 - Disabled
1 - Enabled
Function:
An un-mute will be performed after executing a filter mode change, after a MCLK/LRCK ratio change
or error, and after changing the Functional Mode. When this feature is enabled, this un-mute is affected, similar to attenuation changes, by the Soft and Zero Cross bits (SZC[1:0]). When disabled, an immediate un-mute is performed in these instances.
Note: For best results, it is recommended that this bit be used in conjunction with the RMP_DN bit.
5.10.5 SOFT RAMP-DOWN BEFORE FILTER MODE CHANGE (RMP_DN)
Default = 0
0 - Disabled
1 - Enabled
Function:
A mute will be performed prior to executing a filter mode or de-emphasis mode change. When this
feature is enabled, this mute is affected, similar to attenuation changes, by the Soft and Zero Cross
bits (SZC[1:0]). When disabled, an immediate mute is performed prior to executing a filter mode or
de-emphasis mode change.
Note: For best results, it is recommended that this bit be used in conjunction with the RMP_UP bit.
5.11
Channel Mute (address 0Eh)
7
6
5
4
3
2
1
0
Reserved
Reserved
B3_MUTE
A3_MUTE
B2_MUTE
A2_MUTE
B1_MUTE
A1_MUTE
5.11.1 INDEPENDENT CHANNEL MUTE (XX_MUTE)
Default = 0
0 - Disabled
1 - Enabled
Function:
The Digital-to-Analog converter outputs of the CS42426 will mute when enabled. The quiescent voltage on the outputs will be retained. The muting function is affected, similar to attenuation changes,
by the Soft and Zero Cross bits (SZC[1:0]).
41
CS42426
5.12
Volume Control (addresses 0Fh, 10h, 11h, 12h, 13h, 14h)
7
xx_VOL7
6
xx_VOL6
5
xx_VOL5
4
xx_VOL4
3
xx_VOL3
2
xx_VOL2
1
xx_VOL1
0
xx_VOL0
5.12.1 VOLUME CONTROL (XX_VOL)
Default = 0
Function:
The Digital Volume Control registers allow independent control of the signal levels in 0.5 dB increments from 0 to -127 dB. Volume settings are decoded as shown in Table 14. The volume changes
are implemented as dictated by the Soft and Zero Cross bits (SZC[1:0]). All volume settings less than
-127 dB are equivalent to enabling the MUTE bit for the given channel.
Binary Code
Decimal Value
Volume Setting
00000000
00101000
01010000
01111000
10110100
0
40
80
120
180
0 dB
-20 dB
-40 dB
-60 dB
-90 dB
Table 14. Example Digital Volume Settings
5.13
Channel Invert (address 17h)
7
6
5
4
3
2
1
0
Reserved
Reserved
INV_B3
INV_A3
INV_B2
INV_A2
INV_B1
INV_A1
5.13.1 INVERT SIGNAL POLARITY (INV_XX)
Default = 0
0 - Disabled
1 - Enabled
Function:
When enabled, these bits will invert the signal polarity of their respective channels.
5.14
42
Mixing Control Pair 1 (Channels A1 & B1)(address 18h)
Mixing Control Pair 2 (Channels A2 & B2)(address 19h)
Mixing Control Pair 3 (Channels A3 & B3)(address 1Ah)
7
6
5
4
3
2
1
0
Px_A=B
Reserved
Reserved
Px_ATAPI4
Px_ATAPI3
Px_ATAPI2
Px_ATAPI1
Px_ATAPI0
CS42426
5.14.1 CHANNEL A VOLUME = CHANNEL B VOLUME (PX_A=B)
Default = 0
0 - Disabled
1 - Enabled
Function:
The AOUTAx and AOUTBx volume levels are independently controlled by the A and the B Channel
Volume Control registers when this function is disabled. The volume on both AOUTAx and AOUTBx
are determined by the A Channel Volume Control registers (per A-B pair), and the B Channel Volume
Control registers are ignored when this function is enabled.
43
CS42426
5.14.2 ATAPI CHANNEL MIXING AND MUTING (PX_ATAPIX)
Default = 01001
Function:
The CS42426 implements the channel mixing functions of the ATAPI CD-ROM specification. The
ATAPI functions are applied per A-B pair. Refer to Table 15 and Figure 5 for additional information.
ATAPI4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
ATAPI3
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
ATAPI2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
ATAPI1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
ATAPI0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
AOUTAx
MUTE
MUTE
MUTE
MUTE
aR
aR
aR
aR
aL
aL
aL
aL
a[(L+R)/2]
a[(L+R)/2]
a[(L+R)/2]
a[(L+R)/2]
MUTE
MUTE
MUTE
MUTE
aR
aR
aR
aR
aL
aL
aL
aL
[(aL+bR)/2]
[(aL+bR)/2]
[(bL+aR)/2]
[(aL+bR)/2]
Table 15. ATAPI Decode
44
AOUTBx
MUTE
bR
bL
b[(L+R)/2]
MUTE
bR
bL
b[(L+R)/2]
MUTE
bR
bL
b[(L+R)/2]
MUTE
bR
bL
b[(L+R)/2]
MUTE
bR
bL
[(aL+bR)/2]
MUTE
bR
bL
[(bL+aR)/2]
MUTE
bR
bL
[(aL+bR)/2]
MUTE
bR
bL
[(aL+bR)/2]
CS42426
5.15
ADC Left Channel Gain (address 1Ch)
7
6
5
4
3
2
1
0
Reserved
Reserved
LGAIN5
LGAIN4
LGAIN3
LGAIN2
LGAIN1
LGAIN0
5.15.1 ADC LEFT CHANNEL GAIN (LGAINX)
Default = 00h
Function:
The level of the left analog channel can be adjusted in 1 dB increments as dictated by the Soft and
Zero Cross bits (SZC[1:0]) from +15 to -15 dB. Levels are decoded in two’s complement, as shown
in Table 16.
5.16
ADC Right Channel Gain (address 1Dh)
7
6
5
4
3
2
1
0
Reserved
Reserved
RGAIN5
RGAIN4
RGAIN3
RGAIN2
RGAIN1
RGAIN0
5.16.1 ADC RIGHT CHANNEL GAIN (RGAINX)
Default = 00h
Function:
The level of the right analog channel can be adjusted in 1dB increments as dictated by the Soft and
Zero Cross bits (SZC[1:0]) from +15 to -15dB. Levels are decoded in two’s complement, as shown in
Table 16.
Binary Code
Decimal Value
Volume Setting
001111
001010
000101
000000
111011
110110
110001
+15
+10
+5
0
-5
-10
-15
+15 dB
+10 dB
+5 dB
0 dB
-5 dB
-10 dB
-15 dB
Table 16. Example ADC Input Gain Settings
5.17
Interrupt Control (address 1Eh)
7
6
5
4
3
2
1
0
SP_SYNC
Reserved
DE-EMPH1
DE-EMPH0
INT1
INT0
Reserved
Reserved
5.17.1 SERIAL PORT SYNCHRONIZATION (SP_SYNC)
Default = 0
0 - DAC & ADC Serial Port timings not in phase
1 - DAC & ADC Serial Port timings are in phase
Function:
Forces the LRCK and SCLK from the DAC & ADC Serial Ports to align and operate in phase. This
function will operate when both ports are running at the same sample rate or when operating at different sample rates.
45
CS42426
5.17.2 DE-EMPHASIS SELECT BITS (DE-EMPHX)
Default = 00
00 - Reserved
01 - De-Emphasis for 32 kHz sample rate.
10 - De-Emphasis for 44.1 kHz sample rate.
11 - De-Emphasis for 48 kHz sample rate.
Function:
Used to specify which de-emphasis filter to apply when the FORCE PLL LOCK (FRC_PLL_LK) in
reg06h is enabled.
5.17.3 INTERRUPT PIN CONTROL (INTX)
Default = 00
00 - Active high; high output indicates interrupt condition has occurred
01 - Active low, low output indicates an interrupt condition has occurred
10 - Open drain, active low. Requires an external pull-up resistor on the INT pin.
11 - Reserved
Function:
Determines how the interrupt pin (INT) will indicate an interrupt condition.
5.18
Interrupt Status (address 20h) (Read Only)
7
6
5
4
3
2
1
0
UNLOCK
Reserved
Reserved
Reserved
Reserved
Reserved
OverFlow
Reserved
For all bits in this register, a “1” means the associated interrupt condition has occurred at least once since the register
was last read. A ”0” means the associated interrupt condition has NOT occurred since the last reading of the register.
Reading the register resets all bits to 0. Status bits that are masked off in the associated mask register will always
be “0” in this register.
5.18.1 PLL UNLOCK (UNLOCK)
Default = 0
Function:
PLL unlock status bit. This bit will go high if the PLL becomes unlocked.
5.18.2 ADC OVERFLOW (OVERFLOW)
Default = 0
Function:
Indicates that there is an over-range condition anywhere in the CS42426 ADC signal path.
46
CS42426
5.19
Interrupt Mask (address 21h)
7
6
5
4
3
2
1
0
UNLOCKM
Reserved
Reserved
Reserved
Reserved
Reserved
OverFlowM
Reserved
Default = 00000000
Function:
The bits of this register serve as a mask for the interrupt sources found in the register “Interrupt Status
(address 20h) (Read Only)” on page 46. If a mask bit is set to 1, the error is unmasked, meaning that
its occurrence will affect the INT pin and the status register. If a mask bit is set to 0, the error is
masked, meaning that its occurrence will not affect the INT pin or the status register. The bit positions
align with the corresponding bits in the Interrupt Status register.
5.20
Interrupt Mode MSB (address 22h)
Interrupt Mode LSB (address 23h)
7
6
5
4
3
2
1
0
UNLOCK1
UNLOCK0
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
Reserved
OF1
OF0
Reserved
Reserved
Default = 00000000
Function:
The two Interrupt Mode registers form a 2-bit code for each Interrupt Status register function. There
are three ways to set the INT pin active in accordance with the interrupt condition. In the Rising edge
active mode, the INT pin becomes active on the arrival of the interrupt condition. In the Falling edge
active mode, the INT pin becomes active on the removal of the interrupt condition. In Level active
mode, the INT interrupt pin becomes active during the interrupt condition. Be aware that the active
level(Active High or Low) only depends on the INT(1:0) bits located in the register “Interrupt Control
(address 1Eh)” on page 45.
00 - Rising edge active
01 - Falling edge active
10 - Level active
11 - Reserved
5.21
MuteC Pin Control (address 28h)
7
6
5
4
3
2
1
0
Reserved
Reserved
MCPolarity
M_AOUTA1
M_AOUTB1
M_AOUTA2
M_AOUTB2
M_AOUTA3
M_AOUTB3
Reserved
5.21.1 MUTEC POLARITY SELECT (MCPOLARITY)
Default = 0
0 - Active low
1 - Active high
Function:
Determines the polarity of the MUTEC pin.
47
CS42426
5.21.2 CHANNEL MUTES SELECT (M_AOUTXX)
Default = 1111
0 - Channel mute is not mapped to the MUTEC pin
1 - Channel mute is mapped to the MUTEC pin
Function:
Determines which channel mutes will be mapped to the MUTEC pin. If no channel mute bits are
mapped, then the MUTEC pin is driven to the "active" state as defined by the POLARITY bit. These
Channel Mute Select bits are "ANDed" together in order for the MUTEC pin to go active. This means
that if multiple Channel Mutes are selected to be mapped to the MUTEC pin, then all corresponding
channels must be muted before the MUTEC will go active.
5.22
General Purpose Pin Control (addresses 29h to 2Fh)
7
6
5
4
3
2
1
0
Mode1
Mode0
Polarity
Function4
Function3
Function2
Function1
Function0
5.22.1 MODE CONTROL (MODEX)
Default = 00
00 - Reserved
01 - Mute Mode
10 - GPO/Overflow Mode
11 - GPO, Drive High Mode
Function:
Mute Mode - The pin is configured as a dedicated mute pin. The muting function is controlled by the
Function bits.
GPO/Overflow Mode - The pin is configured as a general purpose output driven low or as a dedicated
ADC overflow pin indicating an over-range condition anywhere in the ADC signal path for either the
left or right channel. The Functionx bits determine the operation of the pin. When configured as a GPO
with the output driven low, the driver is a CMOS driver. When configured to identify an ADC Overflow
condition, the driver is an open drain driver requiring a pull-up resistor.
GPO, Drive High Mode - The pin is configured as a general purpose output driven high.
5.22.2 POLARITY SELECT (POLARITY)
Default = 0
Function:
Mute Mode - If the pin is configured as a dedicated mute output pin, then the polarity bit determines
the polarity of the mapped pin according to the following
0 - Active low
1 - Active high
GPO/Overflow Mode - If the pin is configured as a GPO/Overflow Mode pin, the polarity bit is ignored.
It is recommended that in this mode this bit be set to 0.
GPO, Drive High Mode - If the pin is configured as a general purpose output driven high, the polarity
bit is ignored. It is recommended that in this mode this bit be set to 0.
48
CS42426
5.22.3 FUNCTIONAL CONTROL (FUNCTIONX)
Default = 00000
Function:
Mute Mode - If the pin is configured as a dedicated mute pin, then the functional bits determine which
channel mutes will be mapped to this pin according to the following table.
0 - Channel mute is not mapped to the GPOx pin
1 - Channel mute is mapped to the GPOx pin:
GPOx
Reg Address
Function4
Function3
Function2
Function1
Function0
GPO7
pin 42
GPO6
pin 43
GPO5
pin 44
GPO4
pin 45
GPO3
pin 46
GPO2
pin 47
GPO1
pin 48
29h
M_AOUTA1
M_AOUTB1
M_AOUTA1
M_AOUTB1
M_AOUTA1
M_AOUTB1
M_AOUTA1
M_AOUTB1
M_AOUTA1
M_AOUTB1
M_AOUTA1
M_AOUTB1
M_AOUTA1
M_AOUTB1
M_AOUTA2
M_AOUTA2
M_AOUTB2
M_AOUTA2
M_AOUTB2
M_AOUTA2
M_AOUTB2
M_AOUTA2
M_AOUTB2
M_AOUTA2
M_AOUTB2
M_AOUTA3
M_AOUTA3
M_AOUTB3
M_AOUTA3
M_AOUTB3
M_AOUTA3
M_AOUTB3
M_AOUTB3
Reserved
2Ah
M_AOUTA2
M_AOUTB2
M_AOUTB2
M_AOUTA3
M_AOUTB3
Reserved
M_AOUTA3
M_AOUTB3
M_AOUTA3
M_AOUTB3
Reserved
Reserved
Reserved
Reserved
2Bh
2Ch
2Dh
2Eh
2Fh
Reserved
Reserved
Reserved
GPO/Overflow Mode - If the pin is configured as a GPO/Overflow Mode pin, then the Function1 and
Function0 bits determine how the output will behave according to the following table. It is recommended that in this mode the remaining functional bits be set to 0.
Function1
Function0
GPOx
Driver Type
0
1
0
1
Drive Low
OVFL R or L
CMOS
Open Drain
GPO, Drive High Mode - If the pin is configured as a general purpose output, then the functional bits
are ignored and the pin is driven high. It is recommended that in this mode all the functional bits be
set to 0.
49
CS42426
6 CHARACTERISTICS AND SPECIFICATIONS
(All Min/Max characteristics and specifications are guaranteed over the Specified Operating Conditions. Typical performance characteristics and specifications are derived from measurements taken at nominal supply voltages and
TA = 25° C.)
SPECIFIED OPERATING CONDITIONS (TA = 25° C; AGND=DGND=0, all voltages with respect
to ground; OMCK=12.288 MHz; Master Mode)
Parameter
DC Power Supply
Analog power
Digital internal power
Serial data port interface power
Control port interface power
Ambient Operating Temperature (power applied) CS42426-CQ
CS42426-DQ
Symbol
Min
Typ
Max
Units
VA
VD
VLS
VLC
4.75
3.13
1.8
1.8
5.0
3.3
5.0
5.0
5.25
5.25
5.25
5.25
V
V
V
V
TA
-10
-40
-
+70
+85
°C
°C
ABSOLUTE MAXIMUM RATINGS (AGND = DGND = 0 V; all voltages with respect to ground.)
Parameters
DC Power Supply
Analog power
Digital internal power
Serial data port interface power
Control port interface power
Input Current
(Note 1)
Analog Input Voltage
(Note 2)
Digital Input Voltage
Serial data port interface
(Note 2)
Control port interface
Ambient Operating Temperature(power applied)
CS42426-CQ
CS42426-DQ
Storage Temperature
Symbol
VA
VD
VLS
VLC
Iin
VIN
VIND-S
VIND-C
Min
-0.3
-0.3
-0.3
-0.3
AGND-0.7
-0.3
-0.3
Max
6.0
6.0
6.0
6.0
±10
VA+0.7
VLS+ 0.4
VLC+ 0.4
Units
V
V
V
V
mA
V
V
V
TA
TA
Tstg
-20
-50
-65
+85
+95
+150
°C
°C
°C
WARNING: Operation at or beyond these limits may result in permanent damage to the device. Normal operation is
not guaranteed at these extremes.
Notes: 1. Any pin except supplies. Transient currents of up to ±100 mA on the analog input pins will not cause SCR
latch-up.
2. The maximum over/under voltage is limited by the input current.
50
CS42426
ANALOG INPUT CHARACTERISTICS (TA = 25° C; VA = 5 V, VD = 3.3 V, Logic "0" = DGND
=AGND = 0 V; Logic "1" = VLS = VLC = 5 V; Measurement Bandwidth 10 Hz to 20 kHz unless otherwise specified.
Full scale input sine wave, 997 Hz.; OMCK = 12.288 MHz; Single speed Mode DAC_SCLK = 3.072 MHz; Double
Speed Mode DAC_SCLK = 6.144 MHz; Quad Speed Mode DAC_SCLK = 12.288 MHz.)
Parameter (Note 3)
Symbol Min
Single Speed Mode
(Fs=48 kHz)
Dynamic Range
A-weighted
108
unweighted
105
Total Harmonic Distortion + Noise
THD+N
(Note 4)
-1 dB
-20 dB
-60 dB
Double Speed Mode (Fs=96 kHz)
Dynamic Range
A-weighted
108
unweighted
105
40 kHz bandwidth unweighted
THD+N
Total Harmonic Distortion + Noise
(Note 4)
-1 dB
-20 dB
-60 dB
40kHz bandwidth
-1 dB
Quad Speed Mode
(Fs=192 kHz)
108
Dynamic Range
A-weighted
105
unweighted
40 kHz bandwidth unweighted
Total Harmonic Distortion + Noise
THD+N
(Note 4)
-1 dB
-20 dB
-60 dB
40 kHz bandwidth
-1 dB
Dynamic Performance for All Modes
Interchannel Isolation
Interchannel Phase Deviation
DC Accuracy
Interchannel Gain Mismatch
Gain Drift
Offset Error HPF_FREEZE enabled
HPF_FREEZE disabled
Analog Input
Full-scale Differential Input Voltage
1.9
Input Impedance(differential) (Note 5)
37
Common Mode Rejection Ratio
CMRR
VQ Nominal Voltage
Output Impedance
Maximum allowable DC current
-
CS42426-CQ
Typ
Max
Min
CS42426-DQ
Typ
Max
Unit
114
111
-
106
103
114
111
-
dB
dB
-100
-91
-51
-94
-
-
-100
-91
-51
-92
-
dB
dB
dB
114
111
108
-
106
103
-
114
111
108
-
dB
dB
dB
-100
-91
-51
-97
-94
-
-
-100
-91
-51
-97
-92
-
dB
dB
dB
dB
114
111
108
-
106
103
-
114
111
108
-
dB
dB
dB
-100
-91
-51
-97
-94
-
-
-100
-91
-51
-97
-92
-
dB
dB
dB
dB
110
0.0001
-
-
110
0.0001
-
dB
Degree
0.1
+/-100
0
100
-
-
0.1
+/-100
0
100
-
dB
ppm/°C
LSB
LSB
2.0
82
2.7
50
0.01
2.1
-
1.8
37
-
2.0
82
2.7
50
0.01
2.2
-
Vrms
kΩ
dB
V
kΩ
mA
51
CS42426
FILT+ Nominal Voltage
Output Impedance
Maximum allowable DC current
-
5.0
35
0.01
-
-
5.0
35
0.01
-
V
kΩ
mA
Notes: 3. Typical performance numbers are taken at 25° C. Min/Max performance numbers are guaranteed across
the specified temperature range, TA.
4. Referred to the typical full-scale voltage.
5. Measured between AIN+ and AIN-
A/D DIGITAL FILTER CHARACTERISTICS
Parameter
Single Speed Mode (2 to 50 kHz sample rates)
Passband
(-0.1 dB)
Symbol
(Note 6)
Passband Ripple
Stopband
(Note 6)
Stopband Attenuation
Min
Typ
Max
Unit
0
-
0.47
Fs
-
-
±0.035
dB
0.58
-
-
Fs
-95
-
-
dB
tgd
-
12/Fs
-
s
∆tgd
-
-
0.0
µs
0
-
0.45
Fs
-
-
±0.035
dB
0.68
-
-
Fs
-92
-
-
dB
tgd
-
9/Fs
-
s
∆tgd
-
-
0.0
µs
(Note 6)
0
-
0.24
Fs
-
-
±0.035
dB
(Note 6)
0.78
-
-
Fs
-97
-
-
dB
tgd
-
5/Fs
-
s
∆tgd
-
-
0.0
µs
-
1
20
-
Hz
Hz
-
10
-
Deg
Total Group Delay (Fs = Output Sample Rate)
Group Delay Variation vs. Frequency
Double Speed Mode (50 to 100 kHz sample rates)
Passband
(-0.1 dB)
(Note 6)
Passband Ripple
Stopband
(Note 6)
Stopband Attenuation
Total Group Delay (Fs = Output Sample Rate)
Group Delay Variation vs. Frequency
Quad Speed Mode (100 to 192 kHz sample rates)
Passband
(-0.1 dB)
Passband Ripple
Stopband
Stopband Attenuation
Total Group Delay (Fs = Output Sample Rate)
Group Delay Variation vs. Frequency
High Pass Filter Characteristics
Frequency Response
Phase Deviation
-3.0 dB
-0.13 dB
(Note 7)
@ 20 Hz
(Note 7)
Passband Ripple
-
-
0
dB
Filter Setting Time
-
105/Fs
-
s
Notes: 6. The filter frequency response scales precisely with Fs.
7. Response shown is for Fs equal to 48 kHz. Filter characteristics scale with Fs.
52
0
0
-10
-10
-20
-20
-30
-30
-40
-40
-50
-50
Amplitude (dB)
Amplitude (dB)
CS42426
-60
-70
-80
-60
-70
-80
-90
-90
-100
-100
-110
-110
-120
-120
-130
-130
-140
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
-140
0.40
1.0
Frequency (normalized to Fs)
0.42
0.44
0.46
0.48
0.50
0.52
0.54
0.56
0.58
0.60
Frequency (normalized to Fs)
Figure 20. Single Speed Mode Stopband Rejection
Figure 21. Single Speed Mode Transition Band
0.10
0
-1
0.08
-2
0.05
0.03
-4
Amplitude (dB)
Amplitude (dB)
-3
-5
-6
0.00
-0.03
-7
-0.05
-8
-0.08
-9
-10
0.45
0.46
0.47
0.48
0.49
0.50
0.51
0.52
0.53
0.54
0.55
Frequency (normalized to Fs)
-0.10
0.00
0.05
0.10
0.15
0.20
0.25
0.30
0.35
0.40
0.45
0.50
Frequency (normalized to Fs)
Figure 23. Single Speed Mode Passband Ripple
0
0
-10
-10
-20
-20
-30
-30
-40
-40
-50
-50
Amplitude (dB)
Amplitude (dB)
Figure 22. Single Speed Mode Transition Band (Detail)
-60
-70
-80
-60
-70
-80
-90
-90
-100
-100
-110
-110
-120
-120
-130
-130
-140
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
Frequency (normalized to Fs)
Figure 24. Double Speed Mode Stopband Rejection
1.0
-140
0.40
0.43
0.45
0.48
0.50
0.53
0.55
0.58
0.60
0.63
0.65
0.68
0.70
Frequency (normalized to Fs)
Figure 25. Double Speed Mode Transition Band
53
CS42426
0.10
0
-1
0.08
-2
0.05
-3
0.03
Amplitude (dB)
Amplitude (dB)
-4
-5
-6
0.00
-0.03
-7
-0.05
-8
-0.08
-9
-10
0.40
0.43
0.45
0.48
0.50
0.53
-0.10
0.00
0.55
Frequency (normalized to Fs)
0.05
0.10
0.15
0.20
0.25
0.30
0.35
0.40
0.45
0.50
Frequency (normalized to Fs)
Figure 26. Double Speed Mode Transition Band (Detail)
Figure 27. Double Speed Mode Passband Ripple
0
0
-10
-10
-20
-20
-30
-30
-40
Amplitude (dB)
Amplitude (dB)
-40
-50
-60
-70
-50
-60
-70
-80
-80
-90
-90
-100
-100
-110
-110
-120
-130
-120
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
0.2
0.25
0.3
0
0.10
-1
0.08
-2
0.06
-3
0.04
-4
0.02
-5
-6
-0.04
-0.06
-9
-0.08
-10
0.25
0.3
0.35
0.4
0.45
0.5
0.55
0.6
Frequency (normalized to Fs)
Figure 30. Quad Speed Mode Transition Band (Detail)
54
0.5
0.55
0.6
0.65
0.7
0.75
0.8
0.00
-8
0.2
0.45
-0.02
-7
0.15
0.4
Figure 29. Quad Speed Mode Transition Band
Amplitude (dB)
Amplitude (dB)
Figure 28. Quad Speed Mode Stopband Rejection
0.1
0.35
Frequency (normalized to Fs)
Frequency (normalized to Fs)
-0.10
0.00
0.05
0.10
0.15
0.20
0.25
Frequency (normalized to Fs)
Figure 31. Quad Speed Mode Passband Ripple
CS42426
ANALOG OUTPUT CHARACTERISTICS (TA = 25° C; VA = 5 V, VD = 3.3 V, Logic "0" = DGND
=AGND = 0 V; Logic "1" = VLS = VLC = 5V; Measurement Bandwidth 10 Hz to 20 kHz unless otherwise specified.;
Full scale output 997 Hz sine wave, Test load R L = 3 kΩ, CL = 30 pF; OMCK = 12.288 MHz; Single speed Mode,
DAC_SCLK = 3.072 MHz; Double Speed Mode, DAC_SCLK = 6.144 MHz; Quad Speed Mode, DAC_SCLK =
12.288 MHz.)
Parameter
Symbol Min
Dynamic performance for all modes
Dynamic Range(Note 8)
24-bit A-weighted
108
unweighted
105
16-bit A-Weighted
(Note 9) unweighted
THD+N
Total Harmonic Distortion + Noise
24-bit
0 dB
-20 dB
-60 dB
16-bit
0 dB
(Note 9)
-20 dB
-60 dB
Idle Channel Noise/Signal-to-noise
ratio
Interchannel Isolation
(1
kHz)
Analog Output Characteristics for all modes
Full Scale Differential Output
.88VA
Interchannel Gain Mismatch
Gain Drift
Output Impedance
ZOUT
AC-Load Resistance
RL
3
Load Capacitance
CL
-
CS42426-CQ
Typ
Max
Min
CS42426-DQ
Typ
Max
Unit
114
111
97
94
-
108
105
-
114
111
97
94
-
dB
dB
dB
dB
-100
-91
-51
-94
-74
-34
114
-94
-
-
-100
-91
-51
-94
-74
-34
114
-94
-
dB
dB
dB
dB
dB
dB
dB
90
-
-
90
-
dB
.92VA
0.1
100
100
-
.94VA .88VA
3
30
-
.92VA
0.1
100
100
-
.94VA
Vpp
dB
ppm/°C
Ω
kΩ
30
pF
Notes: 8. One-half LSB of triangular PDF dither is added to data.
9. Performance limited by 16-bit quantization noise.
55
CS42426
D/A DIGITAL FILTER CHARACTERISTICS
Fast Roll-Off
Slow Roll-Off
Parameter
Min
Typ
Max
Min
Typ
Max
Unit
Combined Digital and On-chip Analog Filter Response - Single Speed Mode - 48 kHz
Passband (Note 10)
to -0.01 dB corner
0
0.4535
0
0.4166
Fs
to -3 dB corner
0
0.4998
0
0.4998
Fs
Frequency Response 10 Hz to 20 kHz
-0.01
+0.01
-0.01
+0.01
dB
StopBand
0.5465
0.5834
Fs
StopBand Attenuation
(Note 11)
90
64
dB
Group Delay
12/Fs
6.5/Fs
s
Passband Group Delay Deviation 0 - 20 kHz
±0.41/Fs
±0.14/Fs
s
De-emphasis Error (Note 12)
Fs = 32 kHz
±0.23
±0.23
dB
(Relative to 1 kHz)
Fs = 44.1 kHz
±0.14
±0.14
dB
Fs = 48 kHz
±0.09
±0.09
dB
Combined Digital and On-chip Analog Filter Response - Double Speed Mode - 96 kHz
Passband (Note 10)
to -0.01 dB corner
0
0.4166
0
0.2083
Fs
to -3 dB corner
0
0.4998
0
0.4998
Fs
Frequency Response 10 Hz to 20 kHz
-0.01
0.01
-0.01
0.01
dB
StopBand
0.5834
0.7917
Fs
StopBand Attenuation
(Note 11)
80
70
dB
Group Delay
4.6/Fs
3.9/Fs
s
Passband Group Delay Deviation 0 - 20 kHz
±0.03/Fs
±0.01/Fs
s
Combined Digital and On-chip Analog Filter Response - Quad Speed Mode - 192 kHz
Passband (Note 10)
to -0.01 dB corner
0
0.1046
0
0.1042
Fs
to -3 dB corner
0
0.4897
0
0.4813
Fs
Frequency Response 10 Hz to 20 kHz
-0.01
0.01
-0.01
0.01
dB
StopBand
0.6355
0.8683
Fs
StopBand Attenuation
(Note 11)
90
75
dB
Group Delay
4.7/Fs
4.2/Fs
s
Passband Group Delay Deviation 0 - 20 kHz
±0.01/Fs
±0.01/Fs
s
Notes: 10. Response is clock dependent and will scale with Fs. Note that the response plots (Figures 32 to 55) have
been normalized to Fs and can be de-normalized by multiplying the X-axis scale by Fs.
11. Single and Double Speed Mode Measurement Bandwidth is from stopband to 3 Fs.
Quad Speed Mode Measurement Bandwidth is from stopband to 1.34 Fs.
12. De-emphasis is available only in Single Speed Mode.
56
CS42426
0
20
20
40
40
Amplitude (dB)
Amplitude (dB)
0
60
60
80
80
100
100
120
120
0.4
0.5
0.6
0.7
0.8
Frequency(normalized to Fs)
0.9
1
Figure 32. Single Speed (fast) Stopband Rejection
0.4
0.42
0.44
0.46
0.48
0.5
0.52
Frequency(normalized to Fs)
0.54
0.56
0.58
0.6
Figure 33. Single Speed (fast) Transition Band
0.02
0
1
0.015
2
0.01
0.005
4
Amplitude (dB)
Amplitude (dB)
3
5
6
0
0.005
7
0.01
8
0.015
9
10
0.45
0.46
0.47
0.48
0.49
0.5
0.51
Frequency(normalized to Fs)
0.52
0.53
0.54
0.02
0.55
Figure 34. Single Speed (fast) Transition Band (detail)
0.1
0.15
0.2
0.25
0.3
Frequency(normalized to Fs)
0.35
0.4
0.45
0.5
0
20
20
40
40
Amplitude (dB)
Amplitude (dB)
0.05
Figure 35. Single Speed (fast) Passband Ripple
0
60
80
60
80
100
120
0
100
0.4
0.5
0.6
0.7
0.8
Frequency(normalized to Fs)
0.9
1
Figure 36. Single Speed (slow) Stopband Rejection
120
0.4
0.42
0.44
0.46
0.48
0.5
0.52
Frequency(normalized to Fs)
0.54
0.56
0.58
0.6
Figure 37. Single Speed (slow) Transition Band
57
CS42426
0.02
0
1
0.015
2
0.01
3
Amplitude (dB)
Amplitude (dB)
0.005
4
5
6
0
0.005
7
0.01
8
0.015
9
10
0.45
0.02
0.46
0.47
0.48
0.49
0.5
0.51
Frequency(normalized to Fs)
0.52
0.53
0.54
0.55
Figure 38. Single Speed (slow) Transition Band (detail)
0.1
0.15
0.2
0.25
0.3
Frequency(normalized to Fs)
0.35
0.4
0.45
0.5
0
20
20
40
40
Amplitude (dB)
Amplitude (dB)
0.05
Figure 39. Single Speed (slow) Passband Ripple
0
60
60
80
80
100
100
120
0
120
0.4
0.5
0.6
0.7
0.8
Frequency(normalized to Fs)
0.9
1
Figure 40. Double Speed (fast) Stopband Rejection
0.4
0.42
0.44
0.46
0.48
0.5
0.52
Frequency(normalized to Fs)
0.54
0.56
0.58
0.6
Figure 41. Double Speed (fast) Transition Band
0
0.02
1
0.015
2
0.01
0.005
4
Amplitude (dB)
Amplitude (dB)
3
5
6
0
0.005
7
0.01
8
0.015
9
10
0.45
0.46
0.47
0.48
0.49
0.5
0.51
Frequency(normalized to Fs)
0.52
0.53
0.54
0.55
Figure 42. Double Speed (fast) Transition Band (detail)
58
0.02
0
0.05
0.1
0.15
0.2
0.25
0.3
Frequency(normalized to Fs)
0.35
0.4
0.45
0.5
Figure 43. Double Speed (fast) Passband Ripple
CS42426
0
20
20
40
40
Amplitude (dB)
Amplitude (dB)
0
60
60
80
80
100
100
120
120
0.2
0.3
0.4
0.5
0.6
0.7
Frequency(normalized to Fs)
0.8
0.9
1
Figure 44. Double Speed (slow) Stopband Rejection
0.2
0.3
0.4
0.5
0.6
Frequency(normalized to Fs)
0.7
0.8
Figure 45. Double Speed (slow) Transition Band
0
0.02
1
0.015
2
0.01
0.005
4
Amplitude (dB)
Amplitude (dB)
3
5
6
0
0.005
7
0.01
8
0.015
9
10
0.45
0.46
0.47
0.48
0.49
0.5
0.51
Frequency(normalized to Fs)
0.52
0.53
0.54
0.02
0.55
Figure 46. Double Speed (slow) Transition Band (detail)
20
40
40
Amplitude (dB)
Amplitude (dB)
0.1
0.15
0.2
Frequency(normalized to Fs)
0.25
0.3
0.35
0
20
60
60
80
80
100
100
120
0.2
0.05
Figure 47. Double Speed (slow) Passband Ripple
0
120
0
0.3
0.4
0.5
0.6
0.7
Frequency(normalized to Fs)
0.8
0.9
1
Figure 48. Quad Speed (fast) Stopband Rejection
0.2
0.3
0.4
0.5
0.6
Frequency(normalized to Fs)
0.7
0.8
Figure 49. Quad Speed (fast) Transition Band
59
CS42426
0.2
0
1
0.15
2
0.1
3
Amplitude (dB)
Amplitude (dB)
0.05
4
5
6
0
0.05
7
0.1
8
0.15
9
10
0.45
0.2
0.46
0.47
0.48
0.49
0.5
0.51
Frequency(normalized to Fs)
0.52
0.53
0.54
0.55
Figure 50. Quad Speed (fast) Transition Band (detail)
0
0.05
0.1
0.15
Frequency(normalized to Fs)
0.2
0.25
Figure 51. Quad Speed (fast) Passband Ripple
0
0
20
40
40
Amplitude (dB)
Amplitude (dB)
20
60
60
80
80
100
100
120
120
0.1
0.2
0.3
0.4
0.5
0.6
0.7
Frequency(normalized to Fs)
0.8
0.9
1
Figure 52. Quad Speed (slow) Stopband Rejection
0.1
0.2
0.3
0.4
0.5
0.6
Frequency(normalized to Fs)
0.7
0.8
0.9
Figure 53. Quad Speed (slow) Transition Band
0.02
0
1
0.015
2
0.01
0.005
4
Amplitude (dB)
Amplitude (dB)
3
5
6
0
0.005
7
0.01
8
0.015
9
10
0.45
0.46
0.47
0.48
0.49
0.5
0.51
Frequency(normalized to Fs)
0.52
0.53
0.54
0.55
Figure 54. Quad Speed (slow) Transition Band (detail)
60
0.02
0
0.02
0.04
0.06
0.08
Frequency(normalized to Fs)
0.1
0.12
Figure 55. Quad Speed (slow) Passband Ripple
CS42426
SWITCHING CHARACTERISTICS (For CQ, TA = -10 to +70° C; For DQ, TA = -40 to +85° C;
VA = 5 V, VD =VLC= 3.3 V, VLS = 1.8 V to 5.25 V; Inputs: Logic 0 = DGND, Logic 1 = VLS, CL = 30 pF)
Parameters
Symbol
RST pin Low Pulse Width
Min
Typ
Max
Units
1
-
-
ms
30
-
200
kHz
(Note 13)
PLL Clock Recovery Sample Rate Range
RMCK output jitter
(Note 15)
-
200
-
ps RMS
45
50
55
%
40
50
60
%
DAC_SCLK, ADC_SCLK Duty Cycle
45
50
55
%
DAC_LRCK, ADC_LRCK Duty Cycle
45
50
55
%
RMCK output duty cycle
OMCK Duty Cycle
(Note 14)
Master Mode
RMCK to DAC_SCLK, ADC_SCLK active edge delay
tsmd
0
-
10
ns
RMCK to DAC_LRCK, ADC_LRCK delay
tlmd
0
-
10
ns
Slave Mode
DAC_SCLK, ADC_SCLK Falling Edge to
ADC_SDOUT, ADC_SDOUT Output Valid
tdpd
-
50
ns
DAC_LRCK, ADC_LRCK Edge to MSB Valid
tlrpd
-
20
ns
DAC_SDIN Setup Time Before DAC_SCLK Rising
Edge
tds
-
10
ns
DAC_SDIN Hold Time After DAC_SCLK Rising Edge
tdh
-
30
ns
DAC_SCLK, ADC_SCLK High Time
tsckh
20
-
-
ns
DAC_SCLK, ADC_SCLK Low Time
tsckl
20
-
-
ns
DAC_SCLK, ADC_SCLK rising to DAC_LRCK,
SAI_LRCK Edge
tlrckd
25
-
-
ns
DAC_LRCK, ADC_LRCK Edge to DAC_SCLK,
ADC_SCLK Rising
tlrcks
25
-
-
ns
Notes: 13. After powering up the CS42426, RST should be held low after the power supplies and clocks are settled.
14. See Table 2 on page 15 for suggested OMCK frequencies
15. Limit the loading on RMCK to 1 CMOS load if operating above 24.576 MHz.
DAC_SCLK
ADC_SCLK
(output)
DAC_LRCK
ADC_LRCK
(output)
DA C_LRCK
ADC_LRCK
(input)
t lrckd
t lrcks
t sckh
t sckl
DA C_SCLK
ADC_SCLK
(input)
t
DAC_S DINx
smd
t
lmd
RM CK
Figure 56. Serial Audio Port Master Mode Timing
t lrpd
A DC_SDOUT
t ds
t dh
MSB
t dpd
MS B-1
Figure 57. Serial Audio Port Slave Mode Timing
61
CS42426
SWITCHING CHARACTERISTICS - CONTROL PORT - I2C FORMAT
(For CQ, TA
= -10 to +70° C; For DQ, TA = -40 to +85° C; VA = 5 V, VD =VLS= 3.3 V; VLC = 1.8 V to 5.25 V; Inputs: Logic
0 = DGND, Logic 1 = VLC, CL = 30 pF)
Parameter
Symbol
Min
Max
Unit
SCL Clock Frequency
fscl
-
100
kHz
RST Rising Edge to Start
tirs
500
-
ns
Bus Free Time Between Transmissions
tbuf
4.7
-
µs
Start Condition Hold Time (prior to first clock pulse)
thdst
4.0
-
µs
Clock Low time
tlow
4.7
-
µs
Clock High Time
thigh
4.0
-
µs
Setup Time for Repeated Start Condition
tsust
4.7
-
µs
thdd
0
-
µs
SDA Setup time to SCL Rising
tsud
250
-
ns
Rise Time of SCL and SDA
trc
-
1
µs
Fall Time SCL and SDA
tfc
-
300
ns
tsusp
4.7
-
µs
tack
-
(Note 18)
ns
SDA Hold Time from SCL Falling
(Note 16)
Setup Time for Stop Condition
Acknowledge Delay from SCL Falling
(Note 17)
Notes: 16. Data must be held for sufficient time to bridge the transition time, tfc, of SCL.
17. The acknowledge delay is based on MCLK and can limit the maximum transaction speed.
18.
15
--------------------256 × Fs
15
15
for Single-Speed Mode, --------------------- for Double-Speed Mode, ------------------ for Quad-Speed Mode
128 × Fs
64 × Fs
RST
t
irs
R epe ate d
Stop
Start
Start
t rd
t fd
Stop
S DA
t
buf
t
t
hdst
t
high
t fc
hdst
SCL
t
low
t
hdd
t sud
t ack
t sust
Figure 58. Control Port Timing - I2C Format
62
t rc
t susp
CS42426
SWITCHING CHARACTERISTICS - CONTROL PORT - SPI FORMAT
(For CQ, TA = -10 to +70° C; For DQ, TA = -40 to +85° C; VA = 5 V, VD =VLS= 3.3 V; VLC = 1.8 V to 5.25 V;
Inputs: Logic 0 = DGND, Logic 1 = VLC, CL = 30 pF)
Parameter
Symbol
Min
Typ
Max
Units
fsck
0
-
6.0
MHz
CS High Time Between Transmissions
tcsh
1.0
-
-
µs
CS Falling to CCLK Edge
tcss
20
-
-
ns
CCLK Low Time
tscl
66
-
-
ns
CCLK High Time
tsch
66
-
-
ns
CDIN to CCLK Rising Setup Time
tdsu
40
-
-
ns
tdh
15
-
-
ns
CCLK Falling to CDOUT Stable
tpd
-
-
50
ns
Rise Time of CDOUT
tr1
-
-
25
ns
Fall Time of CDOUT
tf1
-
-
25
ns
CCLK Clock Frequency
(Note 19)
CCLK Rising to DATA Hold Time
(Note 20)
Rise Time of CCLK and CDIN
(Note 21)
tr2
-
-
100
ns
Fall Time of CCLK and CDIN
(Note 21)
tf2
-
-
100
ns
Notes: 19. If Fs is lower than 46.875 kHz, the maximum CCLK frequency should be less than 128 Fs. This is
dictated by the timing requirements necessary to access the Channel Status and User Bit buffer
memory. Access to the control register file can be carried out at the full 6 MHz rate. The minimum
allowable input sample rate is 8 kHz, so choosing CCLK to be less than or equal to 1.024 MHz should
be safe for all possible conditions.
20. Data must be held for sufficient time to bridge the transition time of CCLK.
21. For fsck <1 MHz.
CS
t scl
t css
t sch
t csh
CCLK
t r2
t f2
CDIN
t dsu
t dh
t pd
CDOUT
Figure 59. Control Port Timing - SPI Format
63
CS42426
DC ELECTRICAL CHARACTERISTICS (TA = 25° C; AGND=DGND=0, all voltages with respect
to ground; OMCK=12.288 MHz; Master Mode)
Parameter
Power Supply Current
(Note 22)
Symbol
Min
Typ
Max
Units
IA
ID
ID
ILC
ILS
Ipd
-
90
150
100
250
250
250
-
mA
mA
mA
µA
µA
µA
-
780
1.25
950
1.25
850
1050
-
mW
mW
mW
mW
-
60
40
-
dB
dB
normal operation, VA=5 V
VD=5 V
VD=3.3 V
Interface current, VLC=5V (Note 23)
VLS=5 V
power-down state (all supplies) (Note 24)
Power Consumption
VA=5 V, VD=VLS=VLC=3.3 V
VA=5 V, VD=VLS=VLC=5 V
(Note 22)
normal operation
power-down (Note 24)
normal operation
power-down (Note 24)
Power Supply Rejection Ratio (Note 25)
(1 kHz)
(60 Hz)
PSRR
Notes: 22. Current consumption increases with increasing FS and increasing OMCK. Max values are based on
highest FS and highest OMCK. Variance between speed modes is negligible.
23. ILC measured with no external loading on the SDA pin.
24. Power down mode is defined as RST pin = Low with all clock and data lines held static.
25. Valid with the recommended capacitor values on FILT+ and VQ as shown in Figure .
DIGITAL INTERFACE CHARACTERISTICS (For CQ, TA = +25° C; For DQ, TA = -40 to +85° C)
Parameters (Note 26)
High-Level Input Voltage
Low-Level Input Voltage
High-Level Output Voltage at Io=2 mA
Low-Level Output Voltage at Io=2 mA
Serial Port, Control Port, MUTEC, GPOx
Input Leakage Current
Input Capacitance
MUTEC Drive Current
Symbol
Serial Port
Control Port
Serial Port
Control Port
(Note 27)Serial Port
Control Port
MUTEC, GPOx
VIH
Min
0.7xVLS
0.7xVLC
Typ
-
Max
-
Units
V
V
VIL
-
-
0.2xVLS
0.2xVLC
V
V
VOH
VLS-1.0
VLC-1.0
VA-1.0
-
-
V
V
V
VOL
-
-
0.4
V
Iin
-
8
3
±10
-
µA
pF
mA
(Note 27)
Notes: 26. Serial Port signals include: RMCK, OMCK, ADC_SCLK, ADC_LRCK, DAC_SCLK, DAC_LRCK,
ADC_SDOUT, DAC_SDIN1-3 ADCIN1/2
Control Port signals include: SCL/CCLK, SDA/CDOUT, AD0/CS, AD1/CDIN, INT, RST
27. When operating RMCK above 24.576 MHz, limit the loading on the signal to 1 CMOS load.
64
CS42426
7 PARAMETER DEFINITIONS
Dynamic Range
The ratio of the rms value of the signal to the rms sum of all other spectral components over the specified
bandwidth. Dynamic Range is a signal-to-noise ratio measurement over the specified band width made
with a -60 dBFS signal. 60 dB is added to resulting measurement to refer the measurement to full-scale.
This technique ensures that the distortion components are below the noise level and do not effect the
measurement. This measurement technique has been accepted by the Audio Engineering Society,
AES17-1991, and the Electronic Industries Association of Japan, EIAJ CP-307. Expressed in decibels.
Total Harmonic Distortion + Noise
The ratio of the rms value of the signal to the rms sum of all other spectral components over the specified
band width (typically 10 Hz to 20 kHz), including distortion components. Expressed in decibels. Measured
at -1 and -20 dBFS as suggested in AES17-1991 Annex A.
Frequency Response
A measure of the amplitude response variation from 10 Hz to 20 kHz relative to the amplitude response
at 1 kHz. Units in decibels.
Interchannel Isolation
A measure of crosstalk between the left and right channels. Measured for each channel at the converter's
output with no signal to the input under test and a full-scale signal applied to the other channel. Units in
decibels.
Interchannel Gain Mismatch
The gain difference between left and right channels. Units in decibels.
Gain Error
The deviation from the nominal full-scale analog output for a full-scale digital input.
Gain Drift
The change in gain value with temperature. Units in ppm/°C.
Offset Error
The deviation of the mid-scale transition (111...111 to 000...000) from the ideal. Units in mV.
65
CS42426
8 REFERENCES
1) Cirrus Logic, Audio Quality Measurement Specification, Version 1.0, 1997.
http://www.cirrus.com/products/papers/meas/meas.html
2) Cirrus Logic, AN18: Layout and Design Rules for Data Converters and Other Mixed Signal Devices,
Version 6.0, February 1998.
3) Cirrus Logic, Techniques to Measure and Maximize the Performance of a 120 dB, 96 kHz A/D Converter Integrated Circuit, by Steven Harris, Steven Green and Ka Leung. Presented at the 103rd Convention of the Audio Engineering Society, September 1997.
4) Cirrus Logic, A Stereo 16-bit Delta-Sigma A/D Converter for Digital Audio, by D.R. Welland, B.P.
Del Signore, E.J. Swanson, T. Tanaka, K. Hamashita, S. Hara, K. Takasuka. Paper presented at the
85th Convention of the Audio Engineering Society, November 1988.
5) Cirrus Logic, The Effects of Sampling Clock Jitter on Nyquist Sampling Analog-to-Digital Converters, and on Oversampling Delta Sigma ADC's, by Steven Harris. Paper presented at the 87th Convention of the Audio Engineering Society, October 1989.
6) Cirrus Logic, An 18-Bit Dual-Channel Oversampling Delta-Sigma A/D Converter, with 19-Bit Mono
Application Example, by Clif Sanchez. Paper presented at the 87th Convention of the Audio Engineering Society, October 1989.
7) Cirrus Logic, How to Achieve Optimum Performance from Delta-Sigma A/D and D/A Converters,by
Steven Harris. Presented at the 93rd Convention of the Audio Engineering Society, October 1992.
8) Cirrus Logic, A Fifth-Order Delta-Sigma Modulator with 110 dB Audio Dynamic Range, by I. Fujimori, K. Hamashita and E.J. Swanson. Paper presented at the 93rd Convention of the Audio Engineering Society, October 1992.
9) Philips Semiconductor, The I2C-Bus Specification: Version 2.1, Jan. 2000. http://www.semiconductors.philips.com
66
CS42426
9 PACKAGE DIMENSIONS
64L LQFP PACKAGE DRAWING
E
E1
D D1
1
e
B
∝
A
A1
L
DIM
A
A1
B
D
D1
E
E1
e*
L
MIN
--0.002
0.007
0.461
0.390
0.461
0.390
0.016
0.018
0.000°
∝
* Nominal pin pitch is 0.50 mm
INCHES
NOM
0.55
0.004
0.008
0.472 BSC
0.393 BSC
0.472 BSC
0.393 BSC
0.020 BSC
0.024
4°
MAX
0.063
0.006
0.011
0.484
0.398
0.484
0.398
0.024
0.030
7.000°
MILLIMETERS
NOM
1.40
0.10
0.20
12.0 BSC
10.0 BSC
12.0 BSC
10.0 BSC
0.50 BSC
0.60
4°
MIN
--0.05
0.17
11.70
9.90
11.70
9.90
0.40
0.45
0.00°
MAX
1.60
0.15
0.27
12.30
10.10
12.30
10.10
0.60
0.75
7.00°
Controlling dimension is mm.
JEDEC Designation: MS022
THERMAL CHARACTERISTICS
Parameter
Symbol
Allowable Junction Temperature
Junction to Ambient Thermal Impedance
θJA
Min
Typ
Max
Units
-
-
+135
°C
-
48
-
°C/Watt
67