TI LMV242 Lmv242 dual output, quad-band gsm/gprs power amplifier controller Datasheet

LMV242
www.ti.com
SNWS014C – APRIL 2004 – REVISED MAY 2013
LMV242 Dual Output, Quad-Band GSM/GPRS Power Amplifier Controller
Check for Samples: LMV242
FEATURES
DESCRIPTION
•
•
•
•
•
•
•
•
•
The LMV242 is a power amplifier (PA) controller
intended for use within an RF transmit power control
loop in GSM/GPRS mobile phones. The LMV242
supports all single-supply PA’s including InGaP, HBT
and bipolar power amplifiers. The device operates
with a single supply from 2.6V to 5.5V.
1
2
Support of InGaP HBT, Bipolar Technology
Quad-Band Operation
Shutdown Mode for Power Save in RX Slot
Integrated Ramp Filter
50 dB RF Detector
GPRS Compliant
External Loop Compensation Option
Accurate Temperature Compensation
WSON Package 3x3 mm and Fully Tested Die
Sales
APPLICATIONS
•
•
•
•
•
GSM/GPRS/TDMA/TD_SCDMA Mobile Phone
Pulse RF Control
Wireless LAN
GSM/GPRS Power Amplifier Module
Transmit Module
Included in the PA controller are an RF detector, a
ramp filter and two selectable output drivers that
function as error amplifiers for two different bands.
The LMV242 input interface consists two analog and
two digital inputs. The analog inputs are the RF input,
Ramp voltage input. The digital inputs perform the
function of “Band Select” and “Shutdown/Transmit
Enable” respectively. The “Band Select” function
enables either of two outputs, namely OUT1 when BS
= High, or output OUT2 when BS = Low. The output
that is not enabled is pulled low to the minimum
output voltage. The LMV242 is active in the case
TX_EN = High. When TX_EN = Low the device is in
a low power consumption shutdown mode. During
shutdown both outputs will be pulled low to the
minimum output voltage. Individual PA characteristics
are accommodated by a user selectable external RC
combination.
The LMV242 is offered in fully tested die form as well
as in a 10-lead WSON package and is therefore
especially suitable for small footprint PA module
solutions.
1
2
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2004–2013, Texas Instruments Incorporated
LMV242
SNWS014C – APRIL 2004 – REVISED MAY 2013
www.ti.com
TYPICAL APPLICATION
ANTENNA
PA1
RF1
COUPLER
SWITCH
50:
RF2
PA2
OUT1
OUT2
COMP1
RFIN
1
2
5
9
VDD
LMV242
4
COMP2
10
3
6
7
GND
8
VRAMP
TX_EN
BS
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ABSOLUTE MAXIMUM RATINGS
Supply Voltage
ESD Tolerance
(1) (2)
VDD - GND
(3)
Human Body Model
Machine Model
(4)
150°C Max
Mounting Temperature
(1)
(2)
(3)
(4)
2 kV
200V
−65°C to 150°C
Storage Temperature Range
Junction Temperature
6.5V Max
Infrared or convection (20 sec)
235°C
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test
conditions, see the 2.6V ELECTRICAL CHARACTERISTICS.
If Military/Aerospace specified devices are required, please contact the TI Sales Office/ Distributors for availability and specifications.
Human body model: 1.5 kΩ in series with 100 pF.
The maximum power dissipation is a function of TJ(MAX) , θJA and TA. The maximum allowable power dissipation at any ambient
temperature is PD = (TJ(MAX) - TA)/θJA. All numbers apply for packages soldered directly into a PC board.
OPERATING RATINGS
(1)
Supply Voltage
2.6V to 5.5V
−40°C to +85°C
Operating Temperature Range
VRAMP Voltage Range
0V to 2V
RF Frequency Range
450 MHz to 2 GHz
(1)
2
Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for
which the device is intended to be functional, but specific performance is not ensured. For ensured specifications and the test
conditions, see the 2.6V ELECTRICAL CHARACTERISTICS.
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LMV242
LMV242
www.ti.com
SNWS014C – APRIL 2004 – REVISED MAY 2013
2.6V ELECTRICAL CHARACTERISTICS
Unless otherwise specified, all limits are specified to TJ = 25°C. VDD = 2.6V. Boldface limits apply at temperature extremes
(1)
.
Symbol
IDD
Parameter
Condition
Supply Current
VHIGH
Logic Level to Enable Power
Typ
Max
Units
VOUT = (VDD - GND)/2
6.9
9
12
mA
In Shutdown (TX_EN = 0V)
VOUT = (VDD - GND)/2
0.2
30
μA
See
(2)
See
(2)
Min
1.8
V
VLOW
Logic Level to Disable Power
0.8
V
TON
Turn-on-Time from Shutdown
3.6
6
μs
IEN, IBS
Current into TX_EN and BS Pin
0.03
5
μA
RAMP Amplifier
VRD
VRAMP Deadband
155
206
265
mV
1/RRAMP
Transconductance
See
(3)
70
96
120
μA/V
IOUT
Ramp Amplifier Output Current
VRAMP = 2V
100
162
μA
−50
0
dBm
−63
−13
dBV
RAMP
RF Input
PIN
RF Input Power Range
Logarithmic Slope
20 kΩ // 68 pF between VCOMP1
and VCOMP2
(5)
Logarithmic Intercept
RIN
(4)
(5)
DC Resistance
@ 900 MHz, 20 kΩ // 68 pF
between VCOMP1 and VCOMP2
−1.74
@ 1800 MHz, 20 kΩ // 68 pF
between VCOMP1 and VCOMP2
−1.62
@ 1900 MHz, 20 kΩ // 68 pF
between VCOMP1 and VCOMP2
−1.60
@ 2000 MHz, 20 kΩ // 68 pF
between VCOMP1 and VCOMP2
−1.59
@ 900 MHz, 20 kΩ // 68 pF
between VCOMP1 and VCOMP2
–50.4
@ 1800 MHz, 20 kΩ // 68 if
between VCOMP1 and VCOMP2
–52.3
@ 1900 MHz, 20 kΩ // 68 pF
between VCOMP1 and VCOMP2
–51.9
@ 2000 MHz, 20 kΩ // 68 pF
between VCOMP1 and VCOMP2
–52.3
See
(3)
55.7
(3)
5.1
μA/dB
dBm
Ω
Error Amplifier
GBW
Gain-Bandwidth Product
See
VO
Output Swing from Rail
From Positive Rail, Sourcing,
IO = 7 mA
47
90
115
From Negative Rail Sinking,
IO = −7 mA
52
90
115
IO
(1)
(2)
(3)
(4)
(5)
(6)
Output Short Circuit Current
(6)
Sourcing, VO = 2.4V
10
29.5
Sinking, VO. = 0.2V
10
27.1
MHz
mV
mA
Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that TJ = TA. No specification of parametric performance is indicated in the electrical tables under
conditions of internal self-heating where TJ > TA.
All limits are specified by design or statistical analysis.
Typical values represent the most likely parametric norm.
Power in dBV = dBm + 13 when the impedance is 50Ω.
Slope and intercept are calculated from graphs "VOUT vs. RF input power" where the current is obtained by division of the voltage by 20
kΩ.
The output is not short circuit protected internally. External protection is necessary to prevent overheating and destruction or adverse
reliability.
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LMV242
3
LMV242
SNWS014C – APRIL 2004 – REVISED MAY 2013
www.ti.com
2.6V ELECTRICAL CHARACTERISTICS (continued)
Unless otherwise specified, all limits are specified to TJ = 25°C. VDD = 2.6V. Boldface limits apply at temperature extremes (1).
Symbol
Parameter
en
Output Referred Noise
SR
Slew Rate
Condition
Min
fMEASURE = 10 KHz,
RF Input = 1800 MHz, -10 dBm,
20 kΩ // 68 pF between VCOMP1
and VCOMP2, VOUT =1.4V, set by
VRAMP, (3)
2.1
Typ
Max
Units
700
nV/√Hz
4.4
V/μs
5.0V ELECTRICAL CHARACTERISTICS
Unless otherwise specified, all limits are specified to TJ = 25°C. VDD = 5.0V. Boldface limits apply at temperature extremes
(1)
.
Symbol
IDD
Parameter
Supply Current
VHIGH
Logic Level to Enable Power
VLOW
Logic Level to Disable Power
TON
Turn-on-Time from Shutdown
IEN, IBS
Current into TX_EN and BS Pin
Typ
Max
Units
VOUT = (VDD - GND)/2
Condition
7.8
12
15
mA
In Shutdown (TX_EN = 0V)
VOUT = (VDD - GND)/2
0.4
30
μA
See
(2)
See
(2)
Min
1.8
V
0.8
V
1.5
6
μs
0.03
5
μA
155
206
265
mV
70
96
120
μA/V
100
168
μA
−50
0
dBm
−63
−13
dBV
RAMP Amplifier
VRD
VRAMP Deadband
1/RRAMP
Transconductance
See
IOUT
Ramp Amplifier Output Current
VRAMP = 2V
RAMP
(3)
RF Input
PIN
RF Input Power Range
Logarithmic Slope
(5)
Logarithmic Intercept
RIN
(4)
(5)
DC Resistance
20 kΩ // 68 pF between VCOMP1
and VCOMP2
@ 900 MHz, 20 kΩ // 68 pF
between VCOMP1 and VCOMP2
−1.79
@ 1800 MHz, 20 kΩ // 68 pF
between VCOMP1 and VCOMP2
–1.69
@ 1900 MHz, 20 kΩ // 68 pF
between VCOMP1 and VCOMP2
−1.67
@ 2000 MHz, 20 kΩ // 68 pF
between VCOMP1 and VCOMP2
–1.65
@ 900 MHz, 20 kΩ // 68 pF
between VCOMP1 and VCOMP2
–50.2
@ 1800 MHz, 20 kΩ // 68 pF
between VCOMP1 and VCOMP2
–52.5
@ 1900 MHz, 20 kΩ // 68 pF
between VCOMP1 and VCOMP2
–52.5
@ 2000 MHz, 20 kΩ // 68 pF
between VCOMP1 and VCOMP2
–52.9
See
(3)
55.7
μA/dB
dBm
Ω
Error Amplifier
(1)
(2)
(3)
(4)
(5)
4
Electrical Table values apply only for factory testing conditions at the temperature indicated. Factory testing conditions result in very
limited self-heating of the device such that TJ = TA. No specification of parametric performance is indicated in the electrical tables under
conditions of internal self-heating where TJ > TA.
All limits are specified by design or statistical analysis.
Typical values represent the most likely parametric norm.
Power in dBV = dBm + 13 when the impedance is 50Ω.
Slope and intercept are calculated from graphs "VOUT vs. RF input power" where the current is obtained by division of the voltage by 20
kΩ.
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LMV242
LMV242
www.ti.com
SNWS014C – APRIL 2004 – REVISED MAY 2013
5.0V ELECTRICAL CHARACTERISTICS (continued)
Unless otherwise specified, all limits are specified to TJ = 25°C. VDD = 5.0V. Boldface limits apply at temperature extremes (1).
Symbol
Parameter
Condition
Min
Typ
(3)
Max
GBW
Gain-Bandwidth Product
See
VO
Output Swing from Rail
From Positive Rail, Sourcing,
IO = 7 mA
31
80
105
From Negative Rail Sinking,
IO = −7 mA
35
80
105
IO
Output Short Circuit Current
en
Output Referred Noise
SR
Slew Rate
(6)
(6)
5.7
Sourcing, VO = 4.8V
15
31.5
Sinking, VO = 0.2V
15
31.5
fMEASURE = 10 kHz,
RF Input = 1800 MHz, -10dBm,
20 kΩ // 68 pF between VCOMP1
and VCOMP2, VOUT = 1.4V, set by
VRAMP, (3)
2.5
Units
MHz
mV
mA
770
nV/√Hz
4.9
V/μs
The output is not short circuit protected internally. External protection is necessary to prevent overheating and destruction or adverse
reliability.
CONNECTION DIAGRAM
1
1
10
GND
OUT1
2
2
9
COMP 1
OUT 2
3
3
8
BS
COMP 2
VDD
4
4
7
5
6
10
DIE ID
TX_EN
9
RFIN
VRAMP
8
7
5
Figure 1. WSON-10
Top View
6
Figure 2. Bond Pad Layout
Top View
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LMV242
5
LMV242
SNWS014C – APRIL 2004 – REVISED MAY 2013
www.ti.com
BOND PAD MECHANICAL DIMENSIONS (1)
X/Y Coordinates
Signal Name
Pad Size
Pad Number
X
Y
X
Y
Out 1
1
−281
617
92
92
Out 2
2
−281
490
92
92
Comp2
3
−281
363
92
92
VDD
4
−281
236
92
92
RFIN
5
−281
−617
92
92
VRAMP
6
281
−617
92
92
TX_EN
7
281
−360
92
92
BS
8
281
−118
92
92
Comp1
9
281
20
92
92
GND
10
281
187
92
92
(1)
Dimensions of the bond pad coordinates are in μm Origin of the coordinates: center of the die Coordinates refer to the center of the
bond pad
PIN DESCRIPTIONS (1)
Power Supply
Digital Inputs
Analog Inputs
Compensation
Output
(1)
6
Pin
Name
Description
4
VDD
Positive Supply Voltage
10
GND
Power Ground
7
TX_EN
Schmitt-triggered logic input. A LOW shuts down the whole chip for
battery saving purposes. A HIGH enables the chip.
8
BS
Schmitt-triggered Band Select pin. When BS = H, channel 1 (OUT1)
is selected, when BS = L, channel 2 (OUT2) is selected.
5
RFIN
RF Input connected to the Coupler output with optional attenuation to
measure the Power Amplifier (PA) / Antenna RF power levels.
6
VRAMP
Sets the RF output power level. The useful input voltage range is
from 0.2V to 1.8V, although voltages from 0V to VDD are allowed.
9
Comp1
Connects an external RC network between the Comp1 pin and the
Comp2 pin for an overall loop compensation and to control the
closed loop frequency response. Conventional loop stability
techniques can be used in selecting this network, such as Bode
plots. A good starting value for the RC combination will be C = 68 pF
and R = 0Ω.
3
Comp2
Frequency compensation pin. The BS signal switches this pin either
to OUT1 or to OUT2.
1
Out1
This pin is connected to the PA of either channel 1 or channel 2.
2
Out2
1. All inputs and outputs are referenced to GND (pin 10).
2. For the digital inputs, a LOW is < 0.8V and a HIGH is > 1.8V.
3. RF power detection is performed internally in the LMV242 and only an RF power coupler with optional extra attenuation has to be
used.
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LMV242
LMV242
www.ti.com
SNWS014C – APRIL 2004 – REVISED MAY 2013
BLOCK DIAGRAM
COMP1
9
ERROR AMP 1
RAMP
VDD
6
V/I
1
OUT1
+
8
BS
3
COMP2
4
RAMP
CONVERTER
GND
-
SWITCH
2
-
OUT2
10
+
TX_EN
7
RFIN
5
ERROR AMP 2
10dB
10dB
10dB
10dB
LMV242
DUAL CHANNEL
QUAD-BAND GSM
CONTROLLER
DETECTOR
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LMV242
7
LMV242
SNWS014C – APRIL 2004 – REVISED MAY 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS
Unless otherwise specified, VDD = +2.6V, TJ = 25°C.
VOUT and Log Conformance
vs.
RF Input Power
11
3.00
8
7
2.00
2
6
-40°C
0
1.50
-1
900 MHz
-2
1800 MHz
1.00
4
4.5
5
5.5
Figure 3.
Figure 4.
VOUT and Log Conformance
vs.
RF Input Power @ 900 MHz
VOUT and Log Conformance
vs.
RF Input Power @ 1800 MHz
3.00
2.75
4
2.75
3
2.50
2
2.25
VOUT
2.50
2.25
-40°C
25°C
2.00
1
1.75
0
ERROR
85°C
1.25
-1
VOUT (V)
5
ERROR (dB)
3.00
85°C
0.50
-70 -60 -50 -40 -30 -20 -10
10
1.50
-3
1.00
-4
0.75
3
25°C
20
RF INPUT POWER (dBm)
0
ERROR
-1
-2
-40°C
-3
25°C
-5
0
10
Figure 6.
VOUT and Log Conformance
vs.
RF Input Power @ 1900 MHz
VOUT and Log Conformance
vs.
RF Input Power @ 2000 MHz
5
3.00
4
2.75
3
2.50
2.25
2
2.25
2.00
1
2.75
VOUT
85°C
1.25
-1
4
VOUT
3
1.25
1.00
-4
0.75
-5
0
10
20
1.50
85°C
0
ERROR
-1
-2
-40°C
-3
25°C
85°C
0.50
-70 -60 -50 -40 -30 -20 -10
RF INPUT POWER (dBm)
2
1
-40°C
1.75
-3
25°C
25°C
2.00
-2
-40°C
85°C
0.50
-70 -60 -50 -40 -30 -20 -10
VOUT (V)
0
ERROR (dB)
-40°C
1.75
ERROR
20
5
25°C
VOUT (V)
-4
RF INPUT POWER (dBm)
3.00
-4
-5
0
10
20
RF INPUT POWER (dBm)
Figure 7.
8
85°C
Figure 5.
2.50
2
1
-40°C
85°C
0.50
-70 -60 -50 -40 -30 -20 -10
-5
0
4
VOUT
1.75
1.25
25°C
0.75
20
5
2.00
-2
-40°C
1.00
0.75
10
RF INPUT POWER (dBm)
SUPPLY VOLTAGE (V)
1.00
-5
0
ERROR (dB)
3.5
-4
0.50
-70 -60 -50 -40 -30 -20 -10
ERROR (dB)
3
-3
2000 MHz
0.75
2.5
1
ERROR
1.75
1.25
4
1.50
3
1900 MHz
2.25
5
VOUT (V)
4
VOUT
2.50
25°C
9
VOUT (V)
SUPPLY CURRENT (mA)
10
1.50
5
2.75
85°C
ERROR (dB)
Supply Current
vs.
Supply Voltage
Figure 8.
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LMV242
LMV242
www.ti.com
SNWS014C – APRIL 2004 – REVISED MAY 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Unless otherwise specified, VDD = +2.6V, TJ = 25°C.
Logarithmic Slope
vs.
Frequency
Logarithmic Intercept
vs.
Frequency
-1.50
-49.5
-1.55
-50.0
85°C
-50.5
INTERCEPT (dBm)
SLOPE (PA/dB)
-40°C
-1.60
25°C
-1.65
-1.70
85°C
-51.0
25°C
-51.5
-40°C
-52.0
-1.75
-52.5
-1.80
400
800
1200
1600
-53.0
400
2000
800
1200
1600
2000
FREQUENCY (MHz)
FREQUENCY (MHz)
Figure 9.
Figure 10.
RF Input Impedance
vs.
Frequency @ Resistance and Reactance
Gain and Phase
vs.
Frequency
120
80
60
PHASE
R
50
60
90
40
60
20
10
30
20
GAIN
PHASE (°)
30
GAIN (dB)
IMPEDANCE (:)
40
0
0
0
X
-20
0.5
0.7
0.9
1.1
1.3
1.5
-30
-20
-10
1.7
1.9
2.1
-40
10k
100k
-60
100M
FREQUENCY (Hz)
FREQUENCY (GHz)
Figure 11.
Figure 12.
ICOMP
vs.
VRAMP
PIN
vs.
VRAMP
40
160
30
20
RF INPUT POWER (dBm)
140
120
100
ICOMP (PA)
10M
1M
80
60
40
20
0
MAX PA OUTPUT LEVEL
10
0
-10
-20
-30
-40
-20
-50
-40
-60
0 0.25 0.5 0.75
1
1.25 1.5 1.75
2
0
0.2
0.4
0.6 0.8
1
VRAMP (V)
VRAMP (V)
Figure 13.
Figure 14.
1.2
1.4 1.6
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LMV242
9
LMV242
SNWS014C – APRIL 2004 – REVISED MAY 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Unless otherwise specified, VDD = +2.6V, TJ = 25°C.
Sourcing Current
vs.
Output Voltage
Sinking Current
vs.
Output Voltage
160
160
140
100
120
ISINKING (mA)
120
ISOURCE (mA)
-40°C
140
-40°C
25°C
80
85°C
60
40
100
25°C
80
85°C
60
40
20
20
VCOMP1 = 1V
VCOMP1 = 1.4V
0
0
0
0.4
0.8
1.2
1.6
2
2.4
2.8
0
0.4
0.8
1.2
VOUT (V)
1.6
2
2.4
2.8
VOUT (V)
Figure 15.
Figure 16.
Output Voltage
vs.
Sourcing Current
Output Voltage
vs.
Sinking Current
2
3
VCOMP1 = 1.4V
2.5
-40°C
1.5
VOUT (V)
VOUT (V)
2
85°C
1.5
25°C
85°C
1
25°C
1
0.5
0.5
VCOMP1 = 1V
-40°C
0
0
0
20
40
60
80
0
100
20
40
60
80
Figure 17.
Figure 18.
Closed Loop POUT (PA)
vs.
VRAMP @ GSM 900 MHz Band
Closed Loop POUT (PA)
vs.
VRAMP @ DCS 1800 MHz Band
40
40
85°C
85°C
30
PA OUTPUT POWER (dBm)
PA OUTPUT POWER (dBm)
100
ISINK (mA)
ISOURCE (mA)
25°C
-40°C
20
10
0
-40°C
-10
30
25°C
20
10
0
-40°C
-10
25°C
85°C
-20
-20
0
10
0.25
0.5
0.75
1
1.25
1.5
0
0.25
0.5
0.75
VRAMP (V)
VRAMP (V)
Figure 19.
Figure 20.
Submit Documentation Feedback
1
1.25
1.5
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LMV242
LMV242
www.ti.com
SNWS014C – APRIL 2004 – REVISED MAY 2013
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Unless otherwise specified, VDD = +2.6V, TJ = 25°C.
Closed Loop POUT (PA)
vs.
VRAMP @ PCS 1900 MHz Band
Closed Loop GSM- 900 MHz Band
60
40
25°C
20
10
0
-40°C
-10
25°C
40
|
PA OUTPUT POWER (dBm)
PA OUTPUT POWER (dBm)
85°C
30
20
-40°C
0
25°C
-20
|
85°C
-60
-20
0
0.25
0.5
0.75
1
1.25
85°C
LIMIT
-40
TIME (60 Ps/DIV)
1.5
VRAMP (V)
Figure 21.
Figure 22.
Closed Loop PCS-1900 MHz Band
-40°C
0
25°C
-20
LIMIT
85°C
-40
-60
20
-40°C
0
25°C
-20
LIMIT
85°C
-40
-60
|
20
|
40
PA OUTPUT POWER (dBm)
40
|
60
|
PA OUTPUT POWER (dBm)
Closed Loop DCS-1800 MHz Band
60
TIME (60 Ps/DIV)
TIME (60 Ps/DIV)
Figure 23.
Figure 24.
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LMV242
11
LMV242
SNWS014C – APRIL 2004 – REVISED MAY 2013
www.ti.com
APPLICATION SECTION
POWER CONTROL PRINCIPLES
The LMV242 is a member of the power loop controller family of TI, for quad-band TDMA/GSM solutions. The
typical application diagram demonstrates a basic approach for implementing the quad-band solution around an
RF Power Amplifier (PA). The LMV242 contains a 50 dB Logamp detector and interfaces directly with the
directional coupler.
The LMV242 Base Band (control-) interface consists of 3 signals: TX_EN to enable the device, BS to select
either output 1 or output 2 and VRAMP to set the RF output power to the specified level. The LMV242 gives
maximum flexibility to meet GSM frequency- and time mask criteria for many different single supply Power
Amplifier types like HBT or MesFET in GaAs, SiGe or Si technology. This is accomplished by the programmable
Ramp characteristic from the Base Band and the TX_EN signal along with the external compensation capacitor.
POWER AMPLIFIER CONTROLLED LOOP
This section gives a general overview and understanding of how a typical Power Amplifier control loop works and
how to solve the most common problems confronted in the design.
General Overview
The key benefit of a PA control loop circuit is its immunity to changes in the PA gain control function. When a PA
controller is used, the relationship between gain and gain control voltage (VAPC) of the PA is of no consequence
to the overall transfer function. It is a function of the controller's VRAMP voltage. Based upon the value of VRAMP,
the PA controller will set the gain control voltage of the PA to a level that is necessary to produce the desired
output level. Any temperature dependency in the PA gain control function will be eliminated. Also, non-linearity’s
in the gain transfer function of the PA do not appear in the overall transfer function (POUT vs. VRAMP). The only
requirement is that the gain control function of the PA has to be monotonic. To achieve this, it is crucial, that the
LMV242’s detector is temperature stable.
Typical PA Closed Loop Control Setup
A typical setup of PA control loop is depicted in Figure 25. Beginning at the output of the Power Amplifier (PA),
this signal is fed, usually via a directional coupler, to a detector. The error between the detector output current
IDET and the ramp current IRAMP, representing the selected power setting, drives the inverting input of an op amp,
configured as an integrator. A reference voltage drives the non-inverting input of the op amp. Finally the output of
the integrator op amp drives the gain control input of the power amplifier, which sets the output power. The loop
is stabilized when IDET is equal to IRAMP . Lets examine how this circuit works in detail.
12
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LMV242
LMV242
www.ti.com
SNWS014C – APRIL 2004 – REVISED MAY 2013
PIN1
PA1
SWITCH
COUPLER
ANTENNA
50:
VAPC1
PIN2
PA2
C
VAPC2
COMP1
ERROR AMP1
DETECTOR
OUT1
-
IDET
+
RFIN
COMP2
V/I
+
OUT2
VRAMP
+
IRAMP
ERROR AMP2
LMV242
BS
Figure 25. PA Control Loop
We will assume initially that the output of the PA is at some low level and that the VRAMP voltage is at 1V. The V/I
converter converts the VRAMP voltage to a sinking current IRAMP. This current can only come from the integrator
capacitor C. Current flow from this direction increases the output voltage of the integrator. The output voltage,
which drives the VAPC of the PA, increases the gain (we assume that the PA’s gain control input has a positive
sense, that is, increasing voltage increases gain). The gain will increase, thereby increasing the amplifier’s output
level until the detector output current equals the ramp current IRAMP. At that point, the current through the
capacitor will decrease to zero and the integrator output will be held constant, thereby settling the loop. If
capacitor charge is lost over time, output voltage will decrease. However, this leakage will quickly be corrected
by additional current from the detector. The loop stabilizes to IDET = IRAMP thereby creating a direct relation
between the VRAMP set voltage and the PA output power, independent of the PA's VAPC-POUT characteristics.
Power Control Over Wide Dynamic Range
The circuit as described so far, has been designed to produce a temperature independent output power level. If
the detector has a high dynamic range, the circuit can precisely set PA output levels over a wide power range.
To set a PA output power level, the reference voltage, VRAMP, is varied. To estimate the response of POUT vs.
VRAMP, PIN vs. VRAMP of the LMV242 should be known (POUT = PIN + attenuation as discussed in ATTENUATION
BETWEEN COUPLER AND LMV242 DETECTOR).
The relation between PIN and VRAMP can be constructed out of 2 curves:
• ICOMP vs, VRAMP
• VOUT vs. RF Input Power (detection curve)
IOUT can be calculated by dividing the VOUT of the detection curve by the feedback resistor used for measuring.
With the knowledge that ICOMP = IOUT in a closed loop the resulting function PIN vs. VRAMP is shown in Figure 26.
Extra attenuation should be inserted between PA output and LMV242’s PIN to match their dynamic ranges.
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LMV242
13
LMV242
SNWS014C – APRIL 2004 – REVISED MAY 2013
www.ti.com
40
RF INPUT POWER (dBm)
30
20
MAX PA OUTPUT LEVEL
10
0
-10
-20
-30
-40
-50
-60
0
0.2
0.4
0.6 0.8
1
1.2
1.4 1.6
VRAMP (V)
Figure 26. PIN vs. VRAMP
Using a closed loop to control the PA has benefits over the use of a directly controlled PA. Non-linearity's and
temperature variations present in the PA transfer function do not appear in the overall transfer function, POUT vs.
VRAMP The response of a typical closed loop is given in Figure 27. The shape of this curve is determined by the
response of the controller’s detector. Therefore the detector needs to be accurate, temperature stable and
preferably linear in dB to achieve a accurately controlled output power. The only requirement for the control loop
is that the gain control function of the PA has to be monotonic. With a linear in dB detector, the relation between
VRAMP and PA output power becomes linear in dB as well, which makes calibration of the system easy.
40
PA OUTPUT POWER (dBm)
85°C
30
25°C
-40°C
20
10
0
-40°C
-10
-20
0
0.25
0.5
0.75
1
1.25
1.5
VRAMP (V)
Figure 27. Closed Loop Response
The response time of the loop can be controlled by varying the RC time constant of the integrator. Setting this at
a low level will result in fast output settling but can result in ringing in the output envelope. Setting the RC time
constant to a high value will give the loop good stability but will increase settling time.
ATTENUATION BETWEEN COUPLER AND LMV242 DETECTOR
Figure 28 shows a practical RF power control loop realized by using TI’s LMV242 with integrated RF detector.
The RF signal from the PA passes through a directional coupler on its way to the antenna. Directional couplers
are characterized by their coupling factor, which is in the 10 dB to 30 dB range, typical 20 dB. Because the
coupled output must in its own right deliver some power (in this case to the detector), the coupling process takes
some power from the main output. This manifests itself as insertion loss, the insertion loss being higher for lower
coupling factors.
14
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LMV242
LMV242
www.ti.com
SNWS014C – APRIL 2004 – REVISED MAY 2013
It is very important to choose the right attenuation between PA output and detector input to achieve power
control over the full output power range of the PA. A typical value for the output power of the PA is +35.5 dBm for
GSM and +30 dBm for PCS/DCS. In order to accommodate these levels into the LMV242 detection range the
minimum required total attenuation is about 35 dBm (please refer to typical performance characteristics in the
datasheet and Figure 26). A typical coupler factor is 20 dB. An extra attenuation of about 15 dB should be
inserted.
Extra attenuation Z between the coupler and the RF input of the LMV242 can be achieved by 2 resistors RX and
RY according to Figure 27, where
Z = 20 LOG (RIN / [RIN + RY])
(1)
or
§
¨
¨
©
§ -z
RY = RIN · ¨¨10 20 -1
©
(2)
e.g. RY = 300Ω results in an attenuation of 16.9 dB.
To prevent reflection back to the coupler the impedance seen by the coupler should be 50Ω (RO). The
impedance consists of RX in parallel with RY + RIN. RX can be calculated with the formula:
RX = [RO * (RY + RIN)] / RY
RX = 50 * [1 + (50 / RY)]
(3)
(4)
e.g. with RY = 300Ω, RIN = 50Ω → RX = 58Ω.
ANTENNA
COUPLER
PA
50:
OUT2
COMP1
OUT1
LMV242
RFIN
RIN
50:
RY
COMP2
RX
TX_EN
VRAMP
BS
Figure 28. Simplified PA Control Loop with Extra Attenuation
BASEBAND CONTROL OF THE LMV242
The LMV242 has 3 baseband-controlled inputs:
• VRAMP signal (Base band DAC ramp signal)
• TX_EN is a digital signal (performs the function “Shutdown/Transmit Enable”).
• Band Select (BS)
VRAMP Signal
The actual VRAMP input value sets the RF output power. By applying a certain mask shape to the “Ramp in” pin,
the output voltage level of the LMV242 is adjusting the PA control voltage to get a power level (POUT/dBm) out of
the PA, which is proportional to the single ramp voltage steps. The recommended VRAMP voltage range for RF
power control is 0.2V to 2.0V. The VRAMP input will tolerate voltages from 0V to VDD without malfunction or
damage. The VRAMP input does not change the output level until the level reaches about 206 mV, so offset
voltages in the DAC or amplifier supplying the RAMP signal will not cause excess RF signal output and increased
power consumption.
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LMV242
15
LMV242
SNWS014C – APRIL 2004 – REVISED MAY 2013
www.ti.com
Transmit Enable
Power consumption requirements are supported by the TX_EN function, which puts the entire chip into a power
saving mode to enable maximum standby and talk time while ensuring the output does not glitch excessively
during Power-up and Power-down. The device will be active in the case TX_EN = High, or otherwise go to a low
power consumption shutdown mode. During shutdown the output is pulled low to minimize the output voltage.
Band Select
The LMV242 is especially suitable for PA control loops with 2 PA’s. The 2 outputs to steer the VAPCS of the PA’s
can be controlled with the band select pin. When the band select is LOW output2 is selected, while output1 is
selected when band select is HIGH. The not-selected output is pulled low.
Analog Output
The output is driven by a rail-to-rail amplifier capable of both sourcing and sinking. Several curves are given in
the Typical performance characteristics section regarding the output. The output voltage vs. sourcing/sinking
current curves show the typical voltage drop from the rail over temperature. The sourcing/sinking current vs.
output voltage characteristics show the typical charging/discharging current, which the output is capable of
delivering at a certain voltage. The output is free from glitches when enabled by TX_EN. When TX_EN is low,
the selected output voltage is fixed or near GND.
FREQUENCY COMPENSATION
To compensate and prevent the closed loop arrangement from oscillations and overshoots at the output of the
RF detector/error amplifier of the LMV242, the system can be adjusted by means of external RC components
connected between Comp1 and Comp2. Exact values heavily depend on PA characteristics. A good starting
point is R = 0Ω and C = 68 pF. The vast combination of PA’s and couplers available preclude a generalized
formula for choosing these components. Additional frequency compensation of the closed loop system can be
achieved by adding a resistor (and if needed an inductor) between the LMV242’s output and the VAPC input of the
PA. Please contact TI for additional support.
TIMING DIAGRAM
In order to meet the timemask specifications for GSM, a good timing between the control signals and the RF
signal is essential. According to the specifications the PA’s RF output power needs to ramp within 28 μsec with
minimum overshoot. To achieve this, the output of the PA controller should ramp at the same time as the RF
signal from the Base Band. The ramp signal sets the controllers output to the required value, where the loop
needs a certain time to set this output. Therefore the ramp should be set high some time before the output has to
be high. How much time depends on the setup and the PA used. If the controllers shutdown functionality is used,
the shutdown should be set high about 6 μsec before the ramp is set high.
The control loop can be configured by the following variables:
• Lead time TX_EN event vs. start GSM burst
• Lead time VRAMP vs. start GSM burst
• Ramp profile
• Loop compensation
16
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LMV242
LMV242
www.ti.com
SNWS014C – APRIL 2004 – REVISED MAY 2013
|
6 Psec
MINIMUM
|
TX_EN
|
VRAMP
|
OUT
RF SIGNAL
TIMING VRAMP vs. RF SIGNAL
Figure 29. Timing VRAMP vs. RF Signal
1
2
3
4
10
DIE ID
9
8
7
5
6
Figure 30. 10-Pad Bare Die
Die / Wafer Characteristics
Fabrication Attributes
Physical Die Identification
LMV242A
Die Step
A
Physical Attributes
Wafer Diameter
200 mm
Die Size (Drawn)
889 μm x 1562 μm
35.0 mils x 61.5 mils
Thickness
216 μm Nominal
Min Pitch
123 μm Nominal
Table 1. General Die Information
Bond Pad Opening Size (min)
92 μm x 92μm
Bond Pad Metallization
0.5% Copper_Bal. Aluminum
Passivation
VOM Nitride
Back Side Metal
Bare Back
Back Side Connection
Floating
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LMV242
17
LMV242
SNWS014C – APRIL 2004 – REVISED MAY 2013
www.ti.com
NOTE
Actual die size is rounded to the nearest micron
18
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LMV242
LMV242
www.ti.com
SNWS014C – APRIL 2004 – REVISED MAY 2013
REVISION HISTORY
Changes from Revision B (May 2013) to Revision C
•
Page
Changed layout of National Data Sheet to TI format .......................................................................................................... 18
Submit Documentation Feedback
Copyright © 2004–2013, Texas Instruments Incorporated
Product Folder Links: LMV242
19
PACKAGE OPTION ADDENDUM
www.ti.com
8-Oct-2015
PACKAGING INFORMATION
Orderable Device
Status
(1)
LMV242LD/NOPB
ACTIVE
Package Type Package Pins Package
Drawing
Qty
WSON
NGY
10
1000
Eco Plan
Lead/Ball Finish
MSL Peak Temp
(2)
(6)
(3)
Green (RoHS
& no Sb/Br)
CU SN
Level-3-260C-168 HR
Op Temp (°C)
Device Marking
(4/5)
-40 to 85
242LD
(1)
The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3)
MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5)
Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
Samples
PACKAGE OPTION ADDENDUM
www.ti.com
8-Oct-2015
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Sep-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
LMV242LD/NOPB
Package Package Pins
Type Drawing
WSON
NGY
10
SPQ
Reel
Reel
A0
Diameter Width (mm)
(mm) W1 (mm)
1000
178.0
12.4
Pack Materials-Page 1
3.3
B0
(mm)
K0
(mm)
P1
(mm)
3.3
1.0
8.0
W
Pin1
(mm) Quadrant
12.0
Q1
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Sep-2015
*All dimensions are nominal
Device
Package Type
Package Drawing
Pins
SPQ
Length (mm)
Width (mm)
Height (mm)
LMV242LD/NOPB
WSON
NGY
10
1000
213.0
191.0
55.0
Pack Materials-Page 2
MECHANICAL DATA
NGY0010A
LDA10A (Rev B)
www.ti.com
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated