USB transceivers Ultra-low-power transceiver solutions for mobile and portable applications October 2009 www.stericsson.com Designed for use with ASICs, FPGAs, and system chipsets that interface with the physical layer of the USB connection, these transceivers provide reliable USB performance in a UTMI+ low pin interface (ULPI) format and support a full range of mobile and portable applications. Key features • Fully compliant with: • Universal Serial Bus Specification revision 2.0 • On-The-Go supplement to the USB Specification revision 1.3 • UTMI+ low pin interface (ULPI) Specification revision 1.1 • Battery Charging Specification version 1.0 • USB 2.0 link power management addendum • Interface support to Hi-Speed USB host, peripheral, and dual-role device cores • Ability to support 60-MHz, 8- or 12-pin interface between ASIC and transceiver • 4-bit dual data rate (DDR) • 8-bit single data rate (SDR) • Flexibility with chip select pin polarity • Provides an option to fit the ASIC polarity • Support for wide range of clock frequencies to suit the industrial needs • 13, 19.2, 24, 26, 38.4, and 60 MHz • Variable I/O voltage support • 1.65 V to 3.6 V • Integrated Hi-Speed USB transceiver solutions to minimize external components • Integrated 2.7 V or 3.3 V and 1.8 V regulators • Integrated ESD protection circuit • Integrated VBUS overvoltage protection circuit • Low power consumption for longer battery life • Typical operating current of 13 mA for full-speed and 34 mA for high-speed • Separate I/O voltage supply pins to minimize crosstalk • Input clock mode support, eliminates the external reference clock/oscillator • Fully integrated USB battery-charger detection with automatic hardware detection and software-controlled detection • Robust design to handle noisy clock and power supplies • Very good receiver sensitivity handling data errors with bad cables • UART pass-through mode for serial application • Full industrial grade operating temperature range from −40 °C to +85 °C • ESD compliance: • JESD22-A114F ±2 kV contact human body model (HBM) • JESD22-C101-C ±500 V charged device model (CDM) • IEC 61000-4-2 ±8 kV contact and ±15 kV air on the DP and DM pins • Small foot print for efficient space utilization • WLCSP25, TFBGA36, HVQFN36/32/24 Hi-SPEED USB TRANSCEIVERS WITH ULPI INTERFACE: FOR MOBILE Features Form factor Commercial product code Package type Package dimensions (mm) (L x W x H) Ball or lead pitch (mm) Features ULPI mode ISP1504A1ETTM ISP1504C1ETTM ISP1508AETTM ISP1508BETTM TFBGA36 TFBGA36 3.5 x 3.5 x 0.8 3.5 x 3.5 x 0.8 ISP1703 ISP1704* ISP1514AUKTS ISP1703AUKTS ISP1703BUKTS ISP1704AETTM WLCSP25 WLCSP25 TFBGA36 2.24 x 2.21 x 0.6 2.24 x 2.21 x 0.6 3.5 x 3.5 x 0.8 0.5 0.5 0.4 0.4 0.5 SDR or DDR SDR SDR SDR no Input clock mode Products ISP1514 SDR low Control external charge pump/switch Power ISP1508 Transparent UART mode Crystals and clocks supported (MHz) Others ISP1504 Active chip select pin polarity USB charger detection TARGETED APPLICATIONS • Mobile phones • Digital still and video cameras • Digital TVs • Digital video disc (DVD) recorders • Media players • Set-top boxes (STB) • GPS personal navigation devices • Personal media players (PMPs) • External hard disk drives • Printers and multifunction printer (MFP) • Point of sale terminals • Test and measurement equipment • Gaming consoles • Industrial systems • Communications/networking equipment (wireless access points, LAN switches, network routers) supports resistive method yes AETTM: high BETTM: low supports resistive method yes high supports resistive method yes AUKTS: low BUKTS: high Battery Charging Spec. Rev. 1.0 yes low and high Battery Charging Spec. Rev. 1.0 no no no yes no A1ETTM: 19.2 C1ETTM: 26 13, 19.2, 24, 26 19.2 AUKTS: 19.2 BUKTS: 26 19.2, 26 yes yes no no yes 3.0 to 4.5 3.0 to 4.5 3.0 to 4.5 3.0 to 4.5 3.0 to 4.5 Digital I/O input voltage, VCC(I/O) (V) 1.65 to 3.6 1.65 to 1.95 1.65 to 1.95 1.65 to 1.95 1.65 to 1.95 VBUS protection (V) 5.5 limiting 5.5 limiting 5.5 limiting 16 5.5 limiting Operating temperature (°C) –40 to +85 –40 to +85 –40 to +85 –40 to +85 –40 to +85 Charger detect pin polarity NA NA NA low high Peripheral/host/OTG Peripheral/host/OTG Peripheral/host Peripheral/host/OTG Peripheral/host/OTG Main supply input voltage, VCC (V) USB application * ISP1704 is qualified in EMP reference platform design Hi-SPEED USB TRANSCEIVERS WITH ULPI INTERFACE: GENERIC Form factor Products Features ISP1507A/B ISP1507C/D ISP1507E/F ISP1715 Commercial product code ISP1507ABSTM ISP1507BBSTM ISP1507CBSUM ISP1507DBSUM ISP1507EBSUM ISP1507FBSUM ISP1715AHNUM ISP1715AETTM AHNUM: HVQFN36 AETTM: TFBGA36 AHNUM: 5 x 5 x 0.85 AETTM: 3.5 x 3.5 x 0.8 Package type HVQFN32 HVQFN24 HVQFN24 Package dimensions (mm) (L x W x H) 5 x 5 x 0.85 4 x 4 x 0.85 4 x 4 x 0.85 Ball or lead pitch (mm) - - - 0.5 SDR SDR DDR SDR Transparent UART mode no no no yes Active chip select pin polarity low no no low and high USB charger detection no no no supports resistive method Input clock mode no no no no ABSTM: 19.2 BBSTM: 26 CBSUM: 19.2 DBSUM: 26 EBSUM: 19.2 FBSUM: 26 13, 19.2, 24, 26 Features ULPI mode Crystals and clocks supported (MHz) Control external charge pump/switch Power yes yes yes yes Main supply input voltage, VCC (V) 3.0 to 3.6 3.0 to 3.6 3.0 to 3.6 3.0 to 4.5 Digital I/O input voltage, VCC(I/O) (V) 1.65 to 3.6 1.65 to 3.6 1.65 to 1.95 3.0 to 3.6 VBUS 5 V output: charge pump (mA) 50 no 50 no 5.5 limiting 5.5 limiting 5.5 limiting 5.5 limiting Others VBUS protection (V) Operating temperature (°C) USB application –40 to +85 –40 to +85 –40 to +85 –40 to +85 Peripheral/host/OTG Peripheral/host Peripheral/host/OTG Peripheral/host/OTG usb TRANSCEIVERS Products Form factor Key Feature Package Features Diffrential data receiver output ISP1110 UART mode ISP1302 OTG with carkit support ISP1102BSTS, ISP1102BSTM, ISP1102AWTS, ISP1102AWTM ISP1105BSTM, ISP1105WTS, ISP1105WTM ISP1110VHTS, ISP1110VHTM ISP1302UKTS HBBC 16-pin, 3 x 3 x 0.65 mm 16-pin, 3 x 3 x 0.65 mm 16-pin, 3 x 3 x 0.65 mm NA HQVFN 14-pin, 2.5 x 2.5 x 0.85 mm 16-pin, 3 x 3 x 0.85 mm NA NA Others NA NA NA WLCSP25, 2.5 x 2.5 x 0.6 mm VP/VM VP/VPO, VM/VMO Bidirectional Supported Supported SE0/VM, DAT/VP Bidirectional RCV Supported Supported Supported Supported VPO/VO, VMO/FSE0 VPO/VMO VPO/VO, VMO/FSE0 VPO,VMO SEO/VM, DA/VP Bypass mode VREG (3.3) short to VCC(5.0) Supported Supported NA NA Disable mode Only VCC(5.0) connected NA Supported NA Supported VCC(I/0) only Supported Supported NA Supported Isolate mode Low I/O voltage level (V) 1.65 to 3.6 1.65 to 3.6 1.65 to 2.85 1.4 to 3.6 SOFTCON Supported Supported Supported NA External External Internal Internal (registers) Full-speed and low-speed Full-speed and low-speed Full-speed Full-speed and low-speed Supported NA Supported VBUS comparator (OTG) ±12 ±12 - ±2 Mobile phone, DSC DSC GSM,PDA PDA, DSC, mobile phone Peripheral/host Peripheral/host Peripheral Peripheral/host/OTG Driver data input Sharing mode (isolate) Power ISP1105 Commercial part code Single-ended receiver output Resistor 1.5 kΩ Others ISP1102 Comments Data transfer rates VBUS detect ESD (on D+,D-,VCC(5.0),and GND) (kV) Target applications USB application To order the evaluation kits for these products, contact your local sales office or distributor. For product related information, contact [email protected]. LET’S CREATE IT © ST-Ericsson, 2009 - All rights reserved. ST-Ericsson and the ST-Ericsson logo are trademarks of the ST-Ericsson group of companies or used under a license from STMicroelectronics NV or Telefonaktiebolaget LM Ericsson. All other names are the property of their respective owners. For more information on ST-Ericsson, visit www.stericsson.com Order code: USBTRANSBR_2