4.0x4.0mm RIGHT ANGLE SURFACE MOUNT LED LAMP Part Number: AA4040QWS/D White ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions z Single color. z The source color devices are made with InGaN Light z Suitable for all SMD assembly and solder process. Emitting Diode. z Electrostatic discharge and power surge could damage z Available on tape and reel. the LEDs. z Ideal for backlighting. z It is recommended to use a wrist band or anti- z Package : 500pcs / reel. z Moisture sensitivity level : level 3. electrostatic glove when handling the LEDs. z All devices, equipments and machineries must be z RoHS compliant. electrically grounded. Package Dimensions Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.25(0.01") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAL0882 REV NO: V.4B DATE: OCT/24/2016 PAGE: 1 OF 7 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1201006293 Handling Precautions Compare to epoxy encapsulant that is hard and brittle, silicone is softer and flexible. Although its characteristic significantly reduces thermal stress, it is more susceptible to damage by external mechanical force. As a result, special handling precautions need to be observed during assembly using silicone encapsulated LED products. Failure to comply might lead to damage and premature failure of the LED. 1. Handle the component along the side surfaces by using forceps or appropriate tools. 2. Do not directly touch or handle the silicone lens surface. It may damage the internal circuitry. 3. As silicone encapsulation is permeable to gases, some corrosive substances such as H2S might corrode silver plating of leadframe. Special care should be taken if an LED with silicone encapsulation is to be used near such substances. SPEC NO: DSAL0882 REV NO: V.4B DATE: OCT/24/2016 PAGE: 2 OF 7 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1201006293 Selection Guide Part No. Emitting Color (Material) AA4040QWS/D White (InGaN) Viewing Angle [1] Iv (mcd) [2] @ 20mA Lens Type Water Clear Min. Typ. 2θ1/2 300 600 120° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous Flux: +/-15%. 3. Luminous intensity value is traceable to CIE127-2007 standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Emitting Color Typ. Max. Units Test Conditions VF [1] Forward Voltage White 3.3 4.0 V IF=20mA IR Reverse Current White 50 uA VR = 5V Chromaticity Coordinates White pF VF=0V;f=1MHz x [2] 0.31 y [2] C 0.31 Capacitance White 100 Notes: 1. Forward Voltage: +/-0.1V. 2: Measurement Tolerance Of The Chromaticity Coordinates Is ±0.01. 3. Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Values Units Power dissipation 120 mW DC Forward Current 30 mA Peak Forward Current [1] 150 mA Electrostatic Discharge Threshold (HBM) 250 V 5 V Reverse Voltage Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. 2. Relative humidity levels maintained between 40% and 60% in production area are recommended to avoid the build-up of static electricity – Ref JEDEC/JESD625-A and JEDEC/J-STD-033. SPEC NO: DSAL0882 REV NO: V.4B DATE: OCT/24/2016 PAGE: 3 OF 7 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1201006293 White AA4040QWS/D SPEC NO: DSAL0882 REV NO: V.4B DATE: OCT/24/2016 PAGE: 4 OF 7 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1201006293 White AA4040QWS/D White CIE 0.40 c0 0.35 y b1 0.30 b2 a0 0.25 a2 0.20 0.20 0.25 0.30 0.35 0.40 x a2 b1 x y x y x y 0.263 0.213 0.282 0.245 0.298 0.271 0.282 0.245 0.298 0.271 0.313 0.296 0.265 0.265 0.286 0.299 0.306 0.332 0.242 0.226 0.265 0.265 0.286 0.299 0.313 0.296 0.329 0.325 0.329 0.325 0.358 0.372 0.329 0.371 0.363 0.400 0.306 0.332 0.329 0.371 a0 c0 b2 Notes: Shipment may contain more than one chromaticity regions. Orders for single chromaticity region are generally not accepted. Measurement tolerance of the chromaticity coordinates is ±0.01. SPEC NO: DSAL0882 REV NO: V.4B DATE: OCT/24/2016 PAGE: 5 OF 7 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1201006293 AA4040QWS/D Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAL0882 REV NO: V.4B DATE: OCT/24/2016 PAGE: 6 OF 7 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1201006293 PACKING & LABEL SPECIFICATIONS AA4040QWS/D Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAL0882 REV NO: V.4B DATE: OCT/24/2016 PAGE: 7 OF 7 APPROVED: Wynec CHECKED: Allen Liu DRAWN: W.Q.Zhong ERP: 1201006293