AD AD8194 Buffered 2:1 tmds switch with equalization Datasheet

Buffered 2:1 TMDS Switch
with Equalization
AD8194
FEATURES
FUNCTIONAL BLOCK DIAGRAM
AVCC
CONTROL
LOGIC
S_SEL
VTTI
IP_A[3:0]
IN_A[3:0]
+
AD8194
VTTO
4
4
–
SWITCH
CORE
EQ
IP_B[3:0]
IN_B[3:0]
AVEE
+
–
4
Tx
4
4
+
–
OP[3:0]
ON[3:0]
4
BUFFERED
07004-001
HIGH SPEED
VTTI
Figure 1.
APPLICATIONS
TYPICAL APPLICATION
Advanced television (HDTV) sets
Multiple input displays
Projectors
A/V receivers
Set-top boxes
HDTV SET
HDMI
RECEIVER
SET-TOP BOX
AD8194
DVD PLAYER
07004-002
2 inputs, 1 output HDMI/DVI high speed signal switch
Pin-to-pin compatible with the AD8193
Enables HDMI 1.3-compliant receiver
4 TMDS channels per input/output
Supports 250 Mbps to 2.25 Gbps data rates
Supports 25 MHz to 225 MHz pixel clocks
Fully buffered unidirectional inputs/outputs
Equalized inputs for operation with long HDMI cables
(20 m at 2.25 Gbps)
Matched 50 Ω input and output on-chip terminations
Low added jitter
Single-supply operation (3.3 V)
Standards compliant: HDMI receiver, DVI
32-lead, 5 mm × 5 mm, RoHS-compliant LFCSP
Figure 2. Typical AD8194 Application for HDTV Sets
GENERAL DESCRIPTION
PRODUCT HIGHLIGHTS
The AD8194 is a low cost quad 2:1 TMDS® switch for high
speed HDMI™/DVI video applications. The AD8194 features
equalized inputs, ideal for systems with long cable runs. Its
primary function is to switch the high speed signals from one
of two single-link (HDMI or DVI) sources to the single-link
output. The AD8194 is a fully buffered switch solution with 50 Ω
input and output terminations, providing full-swing output
signal recovery and minimizing reflections for improved system
signal integrity.
1.
The AD8194 is provided in a space-saving, 32-lead, LFCSP,
surface-mount, RoHS-compliant, plastic package and is specified
to operate over the −40°C to +85°C temperature range.
5.
6.
2.
3.
4.
Data supports rates up to 2.25 Gbps, enabling greater than
1080p deep color (12-bit color) HDMI formats and greater
than UXGA (1600 × 2300) DVI resolutions.
Fully buffered inputs and outputs.
Input cable equalizer enables use of long cables at the
input. For a typical 24 AWG cable, the AD8194 compensates for more than 20 m at data rates up to 2.25 Gbps.
Matched 50 Ω on-chip input and output terminations
improve system signal integrity.
Single-pin source select bit.
Low added jitter.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2007 Analog Devices, Inc. All rights reserved.
AD8194
TABLE OF CONTENTS
Features .............................................................................................. 1
Typical Performance Characteristics ..............................................6
Applications....................................................................................... 1
Theory of Operation .........................................................................9
Functional Block Diagram .............................................................. 1
Introduction...................................................................................9
Typical Application........................................................................... 1
Input Channels ..............................................................................9
General Description ......................................................................... 1
Output Channels ...........................................................................9
Product Highlights ........................................................................... 1
Switching Mode .......................................................................... 10
Revision History ............................................................................... 2
Application Notes ........................................................................... 11
Specifications..................................................................................... 3
Switching High Speed Signals................................................... 11
Absolute Maximum Ratings............................................................ 4
Switching Low Speed Signals.................................................... 11
Thermal Resistance ...................................................................... 4
PCB Layout Guidelines.............................................................. 11
Maximum Power Dissipation ..................................................... 4
Outline Dimensions ....................................................................... 16
ESD Caution.................................................................................. 4
Ordering Guide .......................................................................... 16
Pin Configuration and Function Descriptions............................. 5
REVISION HISTORY
11/07—Revision 0: Initial Version
Rev. 0 | Page 2 of 16
AD8194
SPECIFICATIONS
TA = 27°C, AVCC = 3.3 V, VTTI = 3.3 V, VTTO = 3.3 V, AVEE = 0 V, differential input swing = 1000 mV, pattern = PRBS 27 − 1,
data rate = 2.25 Gbps, TMDS outputs terminated with external 50 Ω resistors to 3.3 V, unless otherwise noted.
Table 1.
Parameter
DYNAMIC PERFORMANCE
Maximum Data Rate (DR) per Channel
Bit Error Rate (BER)
Added Deterministic Jitter
Added Random Jitter
Differential Intrapair Skew
Differential Interpair Skew 1
EQUALIZATION PERFORMANCE
Receiver
INPUT CHARACTERISTICS
Input Voltage Swing
Input Common-Mode Voltage (VICM)
OUTPUT CHARACTERISTICS
High Voltage Level
Low Voltage Level
Rise/Fall Time (20% to 80%)
TERMINATION
Input Resistance
Output Resistance
POWER SUPPLY
AVCC
QUIESCENT CURRENT 2
AVCC
VTTI
VTTO
POWER DISSIPATION 3
SOURCE SELECT INTERFACE
Input High Voltage (VIH)
Input Low Voltage (VIL)
Conditions/Comments
Min
NRZ
2.25
Typ
Max
Unit
Gbps
10−9
At output
At output
10
1
1
30
ps (p-p)
ps (rms)
ps
ps
Boost frequency = 1.125 GHz
12
dB
Differential
150
AVCC − 800
Single-ended high speed channel
Single-ended high speed channel
1200
AVCC
mV
mV
AVCC − 400
178
mV
mV
ps
AVCC
AVCC − 600
75
Single-ended
Single-ended
50
50
Operating range
S_SEL
S_SEL
3
Ω
Ω
3.3
3.6
V
50
40
40
429
70
54
65
mA
mA
mA
mW
2
0.8
1
V
V
Differential interpair skew is measured between the TMDS pairs of a single link.
Typical value assumes only the selected HDMI/DVI link is active with nominal signal swings and that the unselected HDMI/DVI link is deactivated. Minimum and
maximum limits are measured at the respective extremes of input termination resistance and input voltage swing.
3
The total power dissipation excludes power dissipated in the 50 Ω off-chip loads.
2
Rev. 0 | Page 3 of 16
AD8194
ABSOLUTE MAXIMUM RATINGS
THERMAL RESISTANCE
Table 2.
Parameter
AVCC to AVEE
VTTI
VTTO
Internal Power Dissipation
High Speed Input Voltage
High Speed Differential
Input Voltage
Source Select (S_SEL)
Storage Temperature Range
Operating Temperature
Range
Junction Temperature
Rating
3.7 V
AVCC + 0.6 V
AVCC + 0.6 V
1.2 W
AVCC − 1.4 V < VIN < AVCC + 0.6 V
2.0 V
AVEE − 0.3 V < VIN < AVCC + 0.6 V
−65°C to +125°C
−40°C to +85°C
150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
θJA is specified for the worst-case conditions: a device soldered
in a 4-layer JEDEC circuit board for surface-mount packages.
θJC is specified for the exposed pad soldered to the circuit board
with no airflow.
Table 3. Thermal Resistance
Package Type
32-Lead LFCSP
θJA
47
θJC
6.8
Unit
°C/W
MAXIMUM POWER DISSIPATION
The maximum power that can be safely dissipated by the
AD8194 is limited by the associated rise in junction temperature. The maximum safe junction temperature for plastic
encapsulated devices is determined by the glass transition
temperature of the plastic, approximately 150°C. Temporarily
exceeding this limit may cause a shift in parametric performance
due to a change in the stresses exerted on the die by the package.
Exceeding a junction temperature of 175°C for an extended
period can result in device failure. To ensure proper operation,
it is necessary to observe the maximum power derating as
determined by the coefficients in Table 3.
ESD CAUTION
Rev. 0 | Page 4 of 16
AD8194
27 AVEE
26 IP_B3
25 IN_B3
PIN 1
INDICATOR
VTTI 3
24 IP_B2
23 IN_B2
22 AVCC
AD8194
IN_A3 4
IP_A3 5
21 IP_B1
20 IN_B1
TOP VIEW
(Not to Scale)
AVCC 6
19 VTTI
ON0 16
ON1 13
VTTO 14
OP0 15
AVEE 11
OP1 12
OP2 9
18 IP_B0
17 IN_B0
ON2 10
OP3 7
ON3 8
NOTES
1. THE AD8194 LFCSP HAS AN EXPOSED PADDLE (ePAD) ON THE UNDERSIDE
OF THE PACKAGE, WHICH AIDS IN HEAT DISSIPATION. THE ePAD MUST BE
ELECTRICALLY CONNECTED TO THE AVEE SUPPLY PLANE TO MEET
THERMAL SPECIFICATIONS.
07004-003
IN_A2 1
IP_A2 2
30 S_SEL
29 IP_A0
28 IN_A0
32 IP_A1
31 IN_A1
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 3. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
1
2
3, 19
4
5
6, 22
7
8
9
10
11, 27, ePAD
12
13
14
15
16
17
18
20
21
23
24
25
26
28
29
30
31
32
1
Mnemonic
IN_A2
IP_A2
VTTI
IN_A3
IP_A3
AVCC
OP3
ON3
OP2
ON2
AVEE
OP1
ON1
VTTO
OP0
ON0
IN_B0
IP_B0
IN_B1
IP_B1
IN_B2
IP_B2
IN_B3
IP_B3
IN_A0
IP_A0
S_SEL
IN_A1
IP_A1
Type 1
HS I
HS I
Power
HS I
HS I
Power
HS O
HS O
HS O
HS O
Power
HS O
HS O
Power
HS O
HS O
HS I
HS I
HS I
HS I
HS I
HS I
HS I
HS I
HS I
HS I
Control
HS I
HS I
Description
High Speed Input Complement.
High Speed Input.
Input Termination Supply. Nominally connected to AVCC.
High Speed Input Complement.
High Speed Input.
Positive Power Supply. 3.3 V nominal.
High Speed Output.
High Speed Output Complement.
High Speed Output.
High Speed Output Complement.
Negative Power Supply. 0 V nominal.
High Speed Output.
High Speed Output Complement.
Output Termination Supply. Nominally connected to AVCC.
High Speed Output.
High Speed Output Complement.
High Speed Input Complement.
High Speed Input.
High Speed Input Complement.
High Speed Input.
High Speed Input Complement.
High Speed Input.
High Speed Input Complement.
High Speed Input.
High Speed Input Complement.
High Speed Input.
Source Selector Pin.
High Speed Input Complement.
High Speed Input.
HS = high speed, I = input, O = output.
Rev. 0 | Page 5 of 16
AD8194
TYPICAL PERFORMANCE CHARACTERISTICS
TA = 27°C, AVCC = 3.3 V, VTTI = 3.3 V, VTTO = 3.3 V, AVEE = 0 V, differential input swing = 1000 mV, pattern = PRBS 27 − 1,
data rate = 2.25 Gbps, TMDS outputs terminated with external 50 Ω resistors to 3.3 V, unless otherwise noted.
HDMI CABLE
AD8194
DIGITAL
PATTERN
GENERATOR
SERIAL DATA
ANALYZER
EVALUATION
BOARD
REFERENCE EYE DIAGRAM AT TP1
TP1
TP2
TP3
07004-004
SMA COAX CABLE
07004-007
250mV/DIV
07004-005
250mV/DIV
Figure 4. Test Circuit Diagram for Rx Eye Diagrams
07004-008
07004-006
250mV/DIV
0.125UI/DIV AT 2.25Gbps
Figure 7. Rx Eye Diagram at TP3, EQ = 12 dB (Cable = 2 m, 30 AWG)
250mV/DIV
0.125UI/DIV AT 2.25Gbps
Figure 5. Rx Eye Diagram at TP2 (Cable = 2 m, 30 AWG)
0.125UI/DIV AT 2.25Gbps
0.125UI/DIV AT 2.25Gbps
Figure 6. Rx Eye Diagram at TP2 (Cable = 20 m, 24 AWG)
Figure 8. Rx Eye Diagram at TP3, EQ = 12 dB (Cable = 20 m, 24 AWG)
Rev. 0 | Page 6 of 16
AD8194
TA = 27°C, AVCC = 3.3 V, VTTI = 3.3 V, VTTO = 3.3 V, AVEE = 0 V, differential input swing = 1000 mV, pattern = PRBS 27 − 1,
data rate = 2.25 Gbps, TMDS outputs terminated with external 50 Ω resistors to 3.3 V, unless otherwise noted.
0.6
0.5
40
0.4
JITTER (ps)
0.3
1080p
12-BIT
30
1080p
8-BIT
20
0.2
0
5
10
15
20
25
HDMI CABLE LENGTH (Meters)
0
07004-028
0
1080i/720p
480p
0
1080p
12-BIT
1080i/720p
480i
DJ (p-p)
RJ (rms)
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
2.2
2.4
DATA RATE (Gbps)
Figure 12. Jitter vs. Data Rate
Figure 9. Jitter vs. Input Cable Length (See Figure 4 for Test Setup)
1.2
50
1.0
40
0.8
JITTER (ps)
EYE HEIGHT (V)
1.65Gbps
480p
10
07004-031
1080p
8-BIT
0.1
0.6
30
20
0.4
10
DJ (p-p)
RJ (rms)
0.2
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.0
2.2
2.4
DATA RATE (Gbps)
0
3.0
07004-029
0
3.2
3.4
3.6
SUPPLY VOLTAGE (V)
07004-032
DETERMINISTIC JITTER (UI)
50
2m TO 5m = 30AWG
10m = 28AWG
20m = 24AWG
Figure 13. Jitter vs. Supply Voltage
Figure 10. Eye Height vs. Data Rate
50
0.9
0.8
40
JITTER (ps)
0.6
0.5
0.4
30
20
0.3
10
DJ (p-p)
RJ (rms)
0.1
0
2.5
2.6
2.7
2.8
2.9
3.0
3.1
3.2
3.3
3.4
SUPPLY VOLTAGE (V)
3.5
3.6
0
0
0.5
1.0
1.5
DIFFERENTIAL INPUT SWING (V)
Figure 14. Jitter vs. Differential Input Swing
Figure 11. Eye Height vs. Supply Voltage
Rev. 0 | Page 7 of 16
2.0
07004-033
0.2
07004-030
EYE HEIGHT (V)
0.7
AD8194
50
40
40
30
30
20
10
10
DJ (p-p)
RJ (rms)
2.7
2.9
3.1
3.3
3.5
3.7
INPUT COMMON-MODE VOLTAGE (V)
0
–40
DJ (p-p)
RJ (rms)
–15
60
60
85
160
58
RISE/FALL TIME 20% TO 80% (ps)
140
56
54
52
50
48
46
44
RISE TIME
FALL TIME
120
100
80
60
40
20
42
–15
10
35
60
85
TEMPERATURE (°C)
0
–40
07004-035
SINGLE-ENDED INPUT RESISTANCE (Ω)
35
Figure 17. Jitter vs. Temperature
Figure 15. Jitter vs. Input Common-Mode Voltage
40
–40
10
TEMPERATURE (°C)
–20
0
20
40
60
80
TEMPERATURE (°C)
Figure 16. Single-Ended Input Resistance vs. Temperature
Figure 18. Rise and Fall Time vs. Temperature
Rev. 0 | Page 8 of 16
100
07004-037
0
2.5
20
07004-036
JITTER (ps)
50
07004-034
JITTER (ps)
TA = 27°C, AVCC = 3.3 V, VTTI = 3.3 V, VTTO = 3.3 V, AVEE = 0 V, differential input swing = 1000 mV, pattern = PRBS 27 − 1,
data rate = 2.25 Gbps, TMDS outputs terminated with external 50 Ω resistors to 3.3 V, unless otherwise noted.
AD8194
THEORY OF OPERATION
The AD8194 is an equalized, buffered TMDS switch with low
added jitter. The output pins are electrically isolated from the
inputs and the input equalizer recovers and transmits an open,
full-swing data eye at the output, even for heavily attenuated
input signals.
The input equalizer of the AD8194 provides 12 dB of high
frequency boost. No specific cable length is suggested for use
with the AD8194 because cable performance varies widely
between manufacturers; however, in general, the equalization of
the AD8194 does not degrade the system signal integrity, even
for short input cables. For a 24 AWG reference cable, the
AD8194 can equalize more than 20 m at data rates up to 2.25
Gbps.
VTTI
50Ω
Because the AD8194 is a TMDS-only switch, a complete HDMI
switch solution requires another component to switch the low
speed DDC channels. Several low cost CMOS switches can be
used along with the AD8194 to make an HDMI 1.3-compliant
2:1 link switch. The requirements for such a switch are as
follows:
•
•
•
Low input capacitance. The HDMI 1.3 specification limits
the total DDC link capacitance for an HDMI sink to less
than 50 pF. This 50 pF limit includes the HDMI connector,
the PCB, the capacitance of the CMOS switch, and whatever capacitance is seen at the input of the HDMI receiver.
Low channel on resistance (RON). Switches with high on
resistance degrade the quality of the DDC signals.
An appropriate form factor to switch the DDC and HPD
signals as necessary.
50Ω
IP_xx
IN_xx
CABLE
EQ
07004-019
The primary function of the AD8194 is to switch the high speed
signals from one of two (HDMI or DVI) single-link sources to
one output. Each source group consists of four differential, high
speed channels. The four high speed channels include a dataword clock and three Transition Minimized Differential Signaling
(TMDS) data channels running at 10× the data-word clock
frequency for data rates up to 2.25 Gbps. All four high speed
channels of the AD8194 are identical; that is, the pixel clock can
be run on any of the four TMDS channels. The AD8194 does
not provide switching of the low speed DDC and CEC signals.
The input termination resistors all have series switches, as
shown in Figure 19. The state of these switches is determined by
the S_SEL signal, which also controls the input selection. The
termination switches for the selected input channel are closed
(terminations present), whereas the termination switches for
the unselected input are open (high-Z inputs).
AVEE
Figure 19. High Speed Input Simplified Schematic
OUTPUT CHANNELS
Each high speed output differential pair is terminated to the
3.3 V VTTO power supply through two single-ended 50 Ω
on-chip resistors, as shown in Figure 20. These matched onchip back terminations absorb reflections on the output TMDS
channels and improve the overall system signal integrity. These
termination resistors are always present in the outputs and they
cannot be switched out.
A reference design that incorporates the AD8194 and a low cost
CMOS switch is described in more detail in the Evaluation
Board section.
VTTO
50Ω
In addition to the AD8194, Analog Devices, Inc., offers several
HDMI switches with integrated DDC, in a variety of form
factors.
50Ω
OPx
INPUT CHANNELS
ONx
IOUT
Each high speed input differential pair terminates to the
3.3 V VTTI power supply through a pair of single-ended 50 Ω
on-chip resistors, as shown in Figure 19. These matched onchip terminations absorb reflections on the input TMDS
channels, properly terminating the inputs and improving
overall system signal integrity.
AVEE
07004-020
INTRODUCTION
Figure 20. High Speed Output Simplified Schematic
In a typical application, the AD8194 output is connected to the
input of an HDMI/DVI receiver, which provides a second set of
matched terminations in accordance with the HDMI 1.3
specification. If no receiver is connected, each of the AD8194
output pins should be tied to 3.3 V through a 50 Ω on-board
termination resistor.
Rev. 0 | Page 9 of 16
AD8194
SWITCHING MODE
Table 5. S_SEL Description
The source selector pin, S_SEL, is used to select which of the
two input groups is routed to the output. Source A is selected
when S_SEL is pulled up to logic high, and Source B is selected
when S_SEL is pulled down to logic low. Logic levels for this pin
are set in accordance with the specifications listed in Table 5. The
AD8194 can be used as a single-link TMDS buffer by setting
S_SEL to one fixed logic value.
S_SEL
0
Selected
Input
Input B
1
Input A
S_SEL also controls the switch status of the input termination
resistors. The termination resistors for the selected input are
always connected, whereas the termination resistors for the
unselected input are always switched out (high-Z inputs).
Rev. 0 | Page 10 of 16
Input Termination Status
Input B terminations enabled, Input A
terminations disabled
Input A terminations enabled, Input B
terminations disabled
AD8194
APPLICATION NOTES
SWITCHING HIGH SPEED SIGNALS
TMDS Signals
The AD8194 is a quad 2:1 TMDS switch that is used to switch
the high speed signals of two input HDMI links to a single
HDMI output.
The audiovisual (AV) data carried on these high speed channels
is encoded by a technique called Transition Minimized Differential Signaling (TMDS) and, in the case of HDMI, is also
encrypted according to the high bandwidth digital content
protection (HDCP) standard.
SWITCHING LOW SPEED SIGNALS
Because the AD8194 is a TMDS-only switch, a complete HDMI
switch solution requires another component to switch the low
speed DDC channels.
The HDMI 1.3 specification places a number of restrictions on
the low speed signal path that limit the selection of a suitable
low cost DDC switch. The first requirement is that the switch
must be bidirectional to convey the I2C® protocol signals that
pass through it. A CMOS device is the simplest switch with this
capability.
The second HDMI requirement for the DDC signals is that the
total DDC signal path capacitance be less than 50 pF. The total
capacitance comprises the HDMI connector, the PC board
traces, the DDC switch, and the input capacitance of the HDMI
receiver. As a practical design consideration, a suitable DDC
switch has a total channel capacitance of less than 10 pF.
Finally, the channel on-resistance (RON) of the DDC switch must
not be too high; otherwise, the voltage drop across it violates
the maximum VOL of the I2C signals. Any switch with an on
resistance of approximately 100 Ω is sufficient in a typical
application, assuming that the end application includes an
I2C-compliant receiver device. Switches with lower channel
on resistance have improved VOL performance.
For the AD8194 evaluation board, the MC74LVX4053 was
chosen to switch the low speed signals. This part has a maximum
RON of 108 Ω and a maximum parasitic capacitance of 10 pF.
Refer to the Evaluation Board section for details on how to use
the MC74LVX4053 with the AD8194 in an application.
PCB LAYOUT GUIDELINES
The AD8194 is used to switch HDMI/DVI video signals, which
are differential, unidirectional, and high speed (up to 2.25 Gbps).
The channels that carry the video data must be controlled
impedance, terminated at the receiver, and capable of operating
up to at least 2.25 Gbps. It is especially important to note that
the differential traces that carry the TMDS signals should be
designed with a controlled differential impedance of 100 Ω.
The AD8194 provides single-ended 50 Ω terminations on chip
for both its inputs and outputs. Transmitter termination is not
fully specified by the HDMI standard, but the inclusion of the
50 Ω output terminations improves the overall system signal
integrity.
In the HDMI/DVI standard, four differential pairs carry the
TMDS signals. For DVI, three of these pairs are dedicated to
carrying RGB video and sync data. For HDMI, audio data is
also interleaved with the video data; the DVI standard does
not incorporate audio information. The fourth high speed
differential pair is used for the AV data-word clock and runs
at one-tenth the speed of the TMDS data channels.
The four high speed channels of the AD8194 are identical.
No concession was made to lower the bandwidth of the fourth
channel for the pixel clock, so any channel can be used for any
TMDS signal. The user chooses which signal is routed over
which channel. Additionally, the TMDS channels are symmetrical;
therefore, the p and n of a given differential pair are interchangeable, provided the inversion is consistent across all inputs
and outputs of the AD8194. However, the routing between
inputs and outputs through the AD8194 is fixed. For example,
Output Channel 0 always switches between Input A0 and
Input B0, and so forth.
The AD8194 buffers the TMDS signals, and the input traces can
be considered electrically independent of the output traces. In
most applications, the quality of the signal on the input TMDS
traces is more sensitive to the PCB layout. Regardless of the
data being carried on a specific TMDS channel, or whether the
TMDS line is at the input or the output of the AD8194, all four
high speed signals should be routed on a PCB in accordance
with the same RF layout guidelines.
Layout for the TMDS Signals
The TMDS differential pairs can be either microstrip traces,
routed on the outer layer of a board, or stripline traces, routed
on an internal layer of the board. If microstrip traces are used,
there should be a continuous reference plane on the PCB layer
directly below the traces. If stripline traces are used, they must
be sandwiched between two continuous reference planes in the
PCB stackup. Additionally, the p and n of each differential pair
must have a controlled differential impedance of 100 Ω. The
characteristic impedance of a differential pair is a function of
several variables, including the trace width, the distance separating
the two traces, the spacing between the traces and the reference
plane, and the dielectric constant of the PC board binder material.
Interlayer vias introduce impedance discontinuities that can
cause reflections and jitter on the signal path; therefore, it is
preferable to route the TMDS lines exclusively on one layer of the
board, particularly for the input traces. Additionally, to prevent
unwanted signal coupling and interference, route the TMDS
signals away from other signals and noise sources on the PCB.
Rev. 0 | Page 11 of 16
AD8194
Any group of four TMDS channels (Input A, Input B, or the
output) should have closely matched trace lengths to minimize
interpair skew. Severe interpair skew can cause the data on the
four different channels of a group to arrive out of alignment
with one another. A good practice is to match the trace lengths
for a given group of four channels to within 0.05 inches on FR4
material.
The length of the TMDS traces should be minimized to reduce
overall signal degradation. Commonly used PC board material
such as FR4 is lossy at high frequencies; therefore, long traces
on the circuit board increase signal attenuation, resulting in
decreased signal swing and increased jitter through intersymbol
interference (ISI).
Ground Current Return
In some applications, it may be necessary to invert the output
pin order of the AD8194. This requires routing the TMDS
traces on multiple layers of the PCB. When routing differential
pairs on multiple layers, it is also necessary to reroute the
corresponding reference plane to provide one continuous
ground current return path for the differential signals. Standard
plated through-hole vias are acceptable for both the TMDS
traces and the reference plane. An example of this is illustrated
in Figure 21.
THROUGH-HOLE VIAS
SILKSCREEN
LAYER 1: SIGNAL (MICROSTRIP)
PCB DIELECTRIC
LAYER 2: GND (REFERENCE PLANE)
PCB DIELECTRIC
LAYER 3: PWR
(REFERENCE PLANE)
PCB DIELECTRIC
LAYER 4: SIGNAL (MICROSTRIP)
SILKSCREEN
Controlling the Characteristic Impedance of a TMDS
Differential Pair
KEEP REFERENCE PLANE
ADJACENT TO SIGNAL ON ALL
LAYERS TO PROVIDE CONTINUOUS
GROUND CURRENT RETURN PATH.
The characteristic impedance of a differential pair depends on a
number of variables, including the trace width, the distance
between the two traces, the height of the dielectric material
between the trace and the reference plane below it, and the
dielectric constant of the PCB binder material. To a lesser
extent, the characteristic impedance also depends upon the
trace thickness and the presence of solder mask.
There are many combinations that can produce the correct
characteristic impedance. It is generally required to work with
the PC board fabricator to obtain a set of parameters to produce
the desired results.
To guarantee a differential pair with a differential impedance of
100 Ω over the entire length of the trace, change the width of
the traces in a differential pair based on how closely one trace is
coupled to the other. When the two traces of a differential pair
are close and strongly coupled, they should have a width that
produces a 100 Ω differential impedance. When the traces split
apart to go into a connector, for example, and are no longer so
strongly coupled, the width of the traces should be increased to
yield a differential impedance of 100 Ω in the new configuration.
07004-012
Both traces of a given differential pair must be equal in length
to minimize intrapair skew. Maintaining the physical symmetry
of a differential pair is integral to ensuring its signal integrity;
excessive intrapair skew can introduce jitter through duty
cycle distortion (DCD). The p and n of a given differential pair
should always be routed together to establish the required 100 Ω
differential impedance. Enough space should be left between
the differential pairs of a given group so that the n of one pair
does not couple to the p of another pair. For example, one technique is to make the interpair distance 4 to 10 times wider than
the intrapair spacing.
Figure 21. Example Routing of Reference Plane
TMDS Terminations
The AD8194 provides internal 50 Ω single-ended terminations
for all of its high speed inputs and outputs. The termination
resistors back-terminate the output TMDS transmission lines.
These back-terminations act to absorb reflections from impedance discontinuities on the output traces, improving the signal
integrity of the output traces and adding flexibility to how the
output traces can be routed. For example, interlayer vias can be
used to route the AD8194 TMDS outputs on multiple layers of the
PCB without severely degrading the quality of the output signal.
In a typical application, the AD8194 output is connected to an
HDMI/DVI receiver or to another device with a 50 Ω single-ended
input termination. It is recommended that the outputs be
terminated with external 50 Ω on-board resistors when the
AD8194 is not connected to another device.
Rev. 0 | Page 12 of 16
AD8194
Auxiliary Control Signals
There are four single-ended control signals associated with each
source or sink in an HDMI/DVI application. These are hot plug
detect (HPD), consumer electronics control (CEC), and two
display data channel (DDC) lines. The two signals on the DDC
bus are SDA and SCL (serial data and serial clock, respectively).
The AD8194, which is a low cost part, does not have any additional capability to switch these signals; other means are
required to switch these signals if required.
In general, it is sufficient to route each auxiliary signal as a
single-ended trace. These signals are not sensitive to impedance
discontinuities, do not require a reference plane, and can be
routed on multiple layers of the PCB. However, it is best to
follow strict layout practices whenever possible to prevent the
PCB design from affecting the overall application. The specific
routing of the HPD, CEC, and DDC lines depends upon the
application in which the AD8194 is being used.
For example, the maximum speed of signals present on the
auxiliary lines is 100 kHz I2C data on the DDC lines; therefore,
any layout that enables 100 kHz I2C to be passed over the DDC
bus should suffice. The HDMI 1.3 specification, however, places
a strict 50 pF limit on the amount of capacitance that can be
measured on either SDA or SCL at the HDMI input connector.
This 50 pF limit includes the HDMI connector, the PCB, the
capacitance of the CMOS switch, and whatever capacitance is
seen at the input of the HDMI receiver. There is a similar limit
of 100 pF of input capacitance for the CEC line.
The parasitic capacitance of traces on a PCB increases with
trace length. To help ensure that a design satisfies the HDMI
specification, the length of the CEC and DDC lines on the PCB
should be made as short as possible. Additionally, if there is a
reference plane in the layer adjacent to the auxiliary traces in
the PCB stackup, relieving or clearing out this reference plane
immediately under the auxiliary traces significantly decreases
the amount of parasitic trace capacitance. An example of the
board stackup is shown in Figure 22.
W
Power Supplies
The AD8194 has three separate power supplies referenced to
a single ground. The supply/ground pairs are
•
•
•
AVCC/AVEE
VTTI/AVEE
VTTO/AVEE
The AVCC/AVEE (3.3 V) supply powers the core of the
AD8194. The VTTI/AVEE supply (3.3 V) powers the input
termination (see Figure 19). Similarly, the VTTO/AVEE
supply (3.3 V) powers the output termination (see Figure 20).
In a typical application, all pins labeled AVEE should be connected directly to ground. All pins labeled AVCC, VTTI, or
VTTO should be connected to 3.3 V. The supplies can also be
powered individually, but care must be taken to ensure that
each stage of the AD8194 is powered correctly.
Power Supply Bypassing
The AD8194 requires minimal supply bypassing. When
powering the supplies individually, place a 0.01 μF capacitor
between each 3.3 V supply pin (AVCC, VTTI, and VTTO) and
ground to filter out supply noise. Generally, bypass capacitors
should be placed near the power pins and should connect directly
to the relevant supplies (without long intervening traces). For
example, to minimize the parasitic inductance of the power
supply decoupling capacitors, minimize the trace length between
capacitor landing pads and the vias as shown in Figure 23.
RECOMMENDED
EXTRA ADDED INDUCTANCE
3W
NOT RECOMMENDED
SILKSCREEN
07004-014
3W
HPD is a dc signal presented by a sink to a source to indicate
that the source EDID is available for reading. The placement
of this signal is not critical, but it should be routed as directly
as possible.
Figure 23. Recommended Pad Outline for Bypass Capacitors
LAYER 1: SIGNAL (MICROSTRIP)
In applications where the AD8194 is powered by a single 3.3 V
supply, it is recommended to use two reference supply planes
and bypass the 3.3 V reference plane to the ground reference
plane with one 220 pF, one 1000 pF, two 0.01 μF, and one 4.7 μF
capacitors. The capacitors should via down directly to the supply
planes and be placed within a few centimeters of the AD8194.
PCB DIELECTRIC
LAYER 2: GND (REFERENCE PLANE)
PCB DIELECTRIC
LAYER 3: PWR (REFERENCE PLANE)
PCB DIELECTRIC
LAYER 4: SIGNAL (MICROSTRIP)
REFERENCE LAYER
RELIEVED UNDERNEATH
MICROSTRIP
07004-013
SILKSCREEN
Figure 22. Example Board Stackup
Rev. 0 | Page 13 of 16
AD8194
Evaluation Board
HDMI cables. However, this arrangement requires crossing over
the TMDS signals on the output side (see Figure 24).
The AD8194 evaluation board illustrates one way to implement
a 2:1 HDMI link switch with an AD8194 and a CMOS switch.
The AD8194 evaluation board deviates from a typical
application in that it uses an HDMI connector for the output as
well as for the inputs. This setup makes it easy to connect
equipment to the AD8194 evaluation board with standard
In a typical application, the output of the AD8194 is routed
directly into an HDMI receiver. Because a receiver is generally
designed to interface directly to an HDMI input connector, it is
not necessary to cross over the TMDS signals in a typical
application (see Figure 25).
19
CROSSOVER
REQUIRED
HDMI
CONNECTOR
1
1
HDMI
CONNECTOR
AD8194
19
19
07004-027
HDMI
CONNECTOR
1
Figure 24. Block Diagram of AD8194 Evaluation Board Showing Output Crossover
19
HDMI
CONNECTOR
HDMI
RECEIVER
07004-026
AD8194
1
Figure 25. HDMI Signals to HDMI Receiver, No Crossover Required
Rev. 0 | Page 14 of 16
AD8194
The low speed switching is performed by an MC74LVX4053.
This part contributes a maximum on resistance of 108 Ω and a
maximum capacitive load of 10 pF. The same select signal
(S_SEL) controls both the AD8194 and the MC74LVX4053.
07004-015
Figure 26 shows the layout of the TMDS traces. These are 100 Ω
differential, controlled-impedance traces. Serpentine traces are
used for some of the paths to match the lengths within a group
of four. The gray traces are routed on the top layer and the black
traces on the bottom layer.
Figure 26. Layout of TMDS Traces
Rev. 0 | Page 15 of 16
AD8194
OUTLINE DIMENSIONS
5.00
BSC SQ
PIN 1
INDICATOR
TOP
VIEW
0.60 MAX
0.60 MAX
0.50
BSC
4.75
BSC SQ
0.50
0.40
0.30
1.00
0.85
0.80
12° MAX
SEATING
PLANE
25
24
32 1
2.85
2.70 SQ
2.55
*EXPOSED
PAD
(BOT TOM VIEW)
17
16
PIN 1
INDICATOR
9 8
0.20 MIN
3.50 REF
0.80 MAX
0.65 TYP
0.05 MAX
0.02 NOM
0.30
0.25
0.18
0.20 REF
COPLANARITY
0.08
092007-A
COMPLIANT TO JEDEC STANDARDS MO-220-VHHD-2
*THE AD8194 HAS A CONDUCTIVE HEAT SLUG TO HELP DISSIPATE HEAT AND ENSURE RELIABLE OPERATION OF
THE DEVICE OVER THE FULL HDMI/DVI TEMPERATURE RANGE. THE SLUG IS EXPOSED ON THE BOTTOM OF
THE PACKAGE AND ELECTRICALLY CONNECTED TO AVEE. IT IS RECOMMENDED THAT NO PCB SIGNAL TRACES
OR VIAS BE LOCATED UNDER THE PACKAGE THAT COULD COME IN CONTACT WITH THE CONDUCTIVE SLUG.
ATTACHING THE SLUG TO AN AVEE PLANE REDUCES THE JUNCTION TEMPERATURE OF THE DEVICE WHICH MAY
BE BENEFICIAL IN HIGH TEMPERATURE ENVIRONMENTS.
Figure 27. 32-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
5 mm × 5 mm Body, Very Thin Quad
(CP-32-8)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD8194ACPZ 1
AD8194ACPZ-R71
AD8194-EVALZ1
1
Temperature
Range
−40°C to +85°C
−40°C to +85°C
Package Description
32-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_VQ], Reel
Evaluation Board
Z = RoHS Compliant Part.
©2007 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D07004-0-11/07(0)
Rev. 0 | Page 16 of 16
Package
Option
CP-32-8
CP-32-8
Ordering
Quantity
1,500