PATENT PENDING PATENT PENDING PATENT PENDING MB2M THRU MB6M MINIATURE GLASS PASSIVATED SINGLE-PHASE BRIDGE RECTIFIER Reverse Voltage - 200 to 600 Volts Forward Current - 0.5 Ampere Case Style MBM FEATURES ♦ Plastic package has Underwriters Laboratory Flammability Classification 94V-0 ♦ This series is UL recognized under Component Index, file number E54214 ♦ Glass passivated chip junctions ♦ High surge overload rating: 35A peak ♦ Saves space on printed circuit board ♦ High temperature soldering guaranteed: 260°C/10 seconds, at 5 lbs. (2.3kg) tension 0.161 (4.10) 0.144 (3.65) 0.190 (4.83) 0.179 (4.55) 0.205 (5.21) 0.195 (4.95) 0.049 (1.24) 0.039 (0.99) 0.106 (2.70) 0.090 (2.30) 0.012 (0.30) 0.008 (0.20) 0.029 (0.74) 0.017 (0.43) MECHANICAL DATA 0.047 (1.19) 0.038 (0.96) 0.117 (2.97) 0.107 (2.72) 0.100 (2.54) MIN. 0-10° 0.016(0.41) 0.006 (0.15) 0.028 (0.71) 0.147 (3.73) 0.137 (3.48) 0.105 (2.67) 0.095 (2.41) 0.020 (0.51) Dimensions in inches and (millimeters) Case: Molded plastic body over passivated junctions Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Polarity: Polarity symbols marked on body Mounting Position: Any Weight: 0.078 ounce, 0.22 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. SYMBOLS MB2M 2 4 6 Maximum repetitive peak reverse voltage VRRM 200 400 600 Volts Maximum RMS voltage VRMS 140 280 420 Volts Maximum DC blocking voltage VDC 200 400 600 Volts Maximum average forward output rectified current at TA=30°C - on glass-epoxy P.C.B. (NOTE 1) on aluminum substrate (NOTE 2) I(AV) 0.5 0.8 Amp Peak forward surge current 8.3msec. single half sinewave superimposed on rated load (JEDEC Method) IFSM 35.0 Amps Rating for fusing (t<8.3ms) I2t 5.0 A2sec Maximum instantaneous forward voltage drop per leg at 0.4A VF 1.0 Volts IR 5.0 500 µA CJ 13.0 pF RΘJL RΘJA RΘJA 20.0 85.0 70.0 °C/W TJ, TSTG -55 to +150 °C Device marking code Maximum DC reverse current at rated DC blocking voltage per leg TA=25°C TA=125°C Typical junction capacitance per leg (NOTE 3) Typical thermal resistance per leg (NOTE 1) (NOTE 1) (NOTE 2) Operating junction and storage temperature range NOTES: (1) On glass epoxy P.C.B. mounted on 0.05 x 0.05” (1.3 x 1.3mm) solder pads (2) On aluminum substrate P.C.B. with an area of 0.8 x 0.8 x 0.25” (20 x 20 x 6.4mm) mounted on 0.05 x 0.05” (1.3 x1.3mm) solder pad (3) Measured at 1.0 MHZ and applied reverse voltage of 4.0 Volts MB4M MB6M UNITS RATINGS AND CHARACTERISTIC CURVES MB2M THRU MB6M FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT PER LEG 0.8 ALUMINUM SUBSTRATE P.C.B. 0.7 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES FIG. 1 - DERATING CURVE FOR OUTPUT RECTIFIED CURRENT GLASS EPOXY P.C.B. 0.6 0.5 0.4 0.3 0.2 0.1 RESISTIVE OR INDUCTIVE LOAD 0 0 20 40 60 35 30 25 f=60 HZ 20 15 10 f=50 HZ 5 0 80 100 120 140 160 TA=40°C SINGLE HALF SINE-WAVE (JEDEC Method) 1.0 CYCLE 1 10 AMBIENT TEMPERATURE, °C INSTANTANEOUS REVERSE LEAKAGE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES FIG. 3 - TYPICAL FORWARD VOLTAGE CHARACTERISTICS PER LEG 10 TJ=150°C 1 TJ=25°C 0.1 PULSE WIDTH 300µs 1% DUTY CYCLE 0.01 0.2 0.4 0.6 0.8 1.0 1.2 1.4 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 5 - TYPICAL JUNCTION CAPACITANCE PER LEG JUNCTION CAPACITANCE, pF 30 TJ=25°C f=1.0 MHZ Vsig=50mVp-p 25 20 15 10 5.0 0 0.1 1 10 REVERSE VOLTAGE, VOLTS 100 NUMBER OF CYCLES 100 200 FIG. 4 - TYPICAL REVERSE LEAKAGE CHARACTERISTICS PER LEG 100 TJ=125°C 10 1 0.1 TJ=25°C 0.01 0 20 40 60 80 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 100