Inductors (Coils) > Chip Inductor (Chip Coil) > for High Frequency Vertical Wire Wound Data Sheet Chip Inductor (Chip Coil) 1 for High Frequency Vertical Wire Wound LQW2BH_13 Series (0805 Size) ■ Dimensions ■ Packaging 1.5±0.2 1.7 -0.1 +0.08 1.5±0.2 2.0±0.2 0.5 min. Code Packaging Minimum Quantity L 180mm Embossed Tape 2000 K 330mm Embossed Tape 7500 1.5±0.2 0.5 min. 0.5 min. (in mm) ■ Rated Value (p: packaging code) Part Number Inductance Test Frequency Rated Current Max. of DC resistance Q (min.) Test Frequency Self Resonance Frequency (min.) LQW2BHN2N7D13p 2.7nH±0.5nH 100MHz 1900mA 0.02ohm 20 250MHz 6000MHz LQW2BHN3N1D13p 3.1nH±0.5nH 100MHz 1800mA 0.02ohm 20 250MHz 6000MHz LQW2BHN3N3D13p 3.3nH±0.5nH 100MHz 1700mA 0.02ohm 20 250MHz 6000MHz LQW2BHN5N6D13p 5.6nH±0.5nH 100MHz 1500mA 0.02ohm 35 250MHz 6000MHz LQW2BHN6N8D13p 6.8nH±0.5nH 100MHz 1400mA 0.02ohm 35 250MHz 5400MHz LQW2BHN8N6D13p 8.6nH±0.5nH 100MHz 1300mA 0.03ohm 35 250MHz 3900MHz LQW2BHN10NJ13p 10nH±5% 100MHz 1320mA 0.03ohm 35 250MHz 3300MHz LQW2BHN12NK13p 12nH±10% 100MHz 1100mA 0.04ohm 40 250MHz 3200MHz LQW2BHN15NK13p 15nH±10% 100MHz 1000mA 0.04ohm 40 250MHz 3100MHz LQW2BHN18NK13p 18.8nH±10% 100MHz 1000mA 0.05ohm 40 250MHz 2600MHz LQW2BHN21NK13p 21nH±10% 100MHz 950mA 0.05ohm 40 250MHz 2200MHz LQW2BHN27NK13p 27nH±10% 100MHz 900mA 0.06ohm 40 250MHz 1800MHz Operating Temperature Range: -40°C to +85°C Continued on the following page. o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2010.9.9 http://www.murata.com/ Inductors (Coils) > Chip Inductor (Chip Coil) > for High Frequency Vertical Wire Wound Data Sheet 2 Continued from the preceding page. ■ Q-Frequency Characteristics (Typ.) ■ Inductance-Frequency Characteristics (Typ.) 100 150 27nH 3.3nH Inductance (nH) 120 90 Q 12nH 60 12nH 10 3.3nH 30 27nH 0 10 1 100 1000 10000 10 100 1000 10000 Frequency (MHz) Frequency (MHz) ■ !Caution/Notice !Caution (Rating) Do not use products beyond the rated current as this may create excessive heat. Notice Solderability of Tin plating termination chip might be deteriorated when low temperature soldering profile where peak solder temperature is below the Tin melting point is used. Please confirm the solderability of Tin plating termination chip before use. o This data sheet is applied for CHIP INDUCTORS (CHIP COILS) used for General Electronics equipment for your design. ! Note: 1. This datasheet is downloaded from the website of Murata Manufacturing co., ltd. Therefore, it’s specifications are subject to change or our products in it may be discontinued without advance notice. Please check with our sales representatives or product engineers before ordering. 2. This datasheet has only typical specifications because there is no space for detailed specifications. Therefore, please approve our product specifications or transact the approval sheet for product specifications before ordering. 2010.9.9 http://www.murata.com/