IE-XS-2W Series FIXED INPUT,ISOLATED & REGULATED Dual Output DC/DC Converter SELECTION GUIDE Input Output Switching Frequency (KHz,Typ) Nominal Range IE0505XS-2W 5 4.75-5.25 ±5 ±100 ±10 70 85 IE0509XS-2W 5 4.75-5.25 ±9 ±56 ±6 61 83 IE0512XS-2W 5 4.75-5.25 ±12 ±42 ±5 62 83 IE0515XS-2W 5 4.75-5.25 ±15 ±33 ±4 64 250 IE1205XS-2W 12 11.4-12.6 ±5 ±100 ±10 75 120 IE1209XS-2W 12 11.4-12.6 ±9 ±56 ±6 61 83 IE1212XS-2W 12 11.4-12.6 ±12 ±42 ±5 65 83 IE1215XS-2W 12 11.4-12.6 ±15 ±33 ±4 64 83 IE2405XS-2W 24 22.8-25.2 ±5 ±100 ±10 78 83 IE2409XS-2W 24 22.8-25.2 ±9 ±56 ±6 69 83 2 Watt load,-40°C to 85°C IE2412XS-2W 24 22.8-25.2 ±12 ±42 ±5 63 83 ◆UL 94V-0 package material IE2415XS-2W 24 22.8-25.2 ±15 ±33 ±4 74 300 FEATURES ◆RoHS compliant ◆Efficiency up to 83% ◆SIP Package ◆Wide temperature performance at full Voltage(VDC) Current(MA) Efficiency (%,Typ) Voltage (VDC) Order code Max Min ◆No heatsink required ◆Low ripple and good EMC Features ◆Industry standard pinout ◆Power sharing on output ◆3KVDC isolation ◆Continuous Short Circuit Protection ISOLATION SPECIFICATIONS ◆Internal SMD construction ◆No external components required ◆Good dynamic feature Parameter Test conditions Min. Isolation test voltage Flash tested for 1 minute and 1mA max 3000 Typ. Max. Units VDC Isolation resistance Test at Viso=500VDC 1000 MΩ MODEL SELECTION IE①05②05③X④ S⑤-2W⑥ ①Product Series ③Output Voltage ⑤SIP Package ②Input Voltage ④Fixed Input ⑥Rated Power OUTPUT SPECIFICATIONS APPLICATIONS Parameter Test conditions Min Typ. Max. Units The IE_XS-2W series are specially designed for applications where a group of polar power supplies are isolated from the Output power 2 W input power supply in a distributed power supply system on a Line regulation For Vin change of ±5% ±0.5 % Load regulation 10% to 100% full load ±1.5 % circuit board. These products apply to: 1) where the voltage of the input power supply is fixed (voltage variation ≤±5%); 2) where isolation is necessary between input and output 0.2 Output voltage accuracy 100% full load ±3 % Temperature drift 100% full load 0.03 %/°C (isolation voltage ≤3000VDC); Output Ripple* 20MHz Bandwidth 20 30 MV p-p 3) where the regulation of the output voltage and the output Output Noise* 20MHz Bandwidth 50 150 MV p-p Full load,nominal input 100 ripple noise are demanded. Switching frequency Khz * Test ripple and noise by "parallel cable" method. See detailed operation instructions at Testing of Power Converter section, application notes. MICRODC reserves the copyright http://www.microdc.cn Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 1 of 2 IE-XS-2W Series Filtering TEMPERATURE CHARACTERISTICS Parameter Conditions Min. Typ. Storage humidity range Operating temperature -40 Storage temperature Lead temperature -55 1.5mm from case for 10 seconds 40 Temp.rise at full load Cooling Max. Units 95 % 85 °C 125 °C 58 °C 300 °C To get an extreme low ripple,an "LC"filtering network may be connected to the input and output ends of the DC/DC converter.Which may produce a more significant filtering effect.It should also be noted that the inductance and the frequency of the "LC"filtering network should be staggered with the DC/DC frequency to avoid mutual interference see (Figure 1). Free air convection Case material Plastic(UL94-V0) IE-XS-2W Continuous Short circuit protection 1 MTBF S 3500 K hours Weight 5.2 g *Supply voltage must be discontinued at the end of short circuit duration. In some circuits which are sensitive to noise and ripple.a filtering capacitor may be added to the DC/DC output end and input end to reduce the noise and ripple. However, the capacitance of the output filter capacitor must be proper. If the capacitance is too big, a startup problem might arise. For every channel of output, provided the safe and reliable operation is ensured, the greatest capacitance of its filter capacitor sees (Table 1). TYPICAL CHARACTERISTICS Temperature Derating Graph EXTERNAL CAPACITOR TABLE (TABLE 1) Cin Vout Vin (VDC) 5 (μF) 4.7 Cout (VDC) ±5 (μF) 4.7 12 2.2 ±9 2.2 24 0.47 ±12 1.0 It's not recommend to connect any external capacitor in the application field with less than 0.5 watt output. OUTLINE DIMENSIONS & PIN CONNECTIONS SIZE Graph RECOMMENDED FOOTPRINT Top view,grid:2.54mm(0.1inch) diameter:1.00mm(0.039inch) Overload Protection Under normal operating conditions , the output circuit of these products has no protection against over-current and short-circuits.The simplest method is to connect a self-recovery fuse in series at the input end or add a circuit breaker to the circuit. FOOTPRINT DETAILS Pin Note: Unit:mm(inch) Pin section:0.50*0.3mm(0.020*0.012inch) Pin section tolerances:±0.10mm(±0.004inch) General tolerances:±0.25mm(±0.010inch) Function 1 VIN 2 GND 7 +V0 9 -V0 10 0V When the environment temperature is higher than 71 C, the product output power should be less then 71°C, 60% of the rated power. No parallel connection or plug and play. Use dual output simultaneously, forbid opening Output pin (0V) to use as single output. All specifications typical at TA=25°C, nominal input voltage and rated output current unless otherwise specified.Another 24V products, please inquire Our technical department! Requirement on output load To ensure this module can operate efficiently and reliably, a minimum load is specified for this kind of DC/DC converter in addition to a maximum load(namely full load).During operation, make sure the specified range of input voltage is not exceeded,the minimum output load is not less than 10 10% of the full load, and that this product should never be operated under no load! RoHS COMPLIANT INFORMATION This series is compatible with RoHS soldering systems with a peak wave solder temperature of 300°C for 10 seconds. The pin termination finish on the SIP package type is Tin Plate, Hot Dipped over Matte Tin with Nickel Preplate. The DIP types are Matte Tin over Nickel Preplate. Both types in this series are backward compatible with Sn/Pb soldering systems. Microdc Professional Power Module,Inc. Tel:0086-20-86000646 REACH COMPLIANT INFORMATION E-mail:[email protected] Website:http://www.microdc.cn http://www.microdc.cn This series has proven that this product does not contain harmful chemicals, it also has harmful chemical substances through the registration, inspection and approval. Technical Enquiries-Email:[email protected] Tel:0086-20-86000646 Page 2 of 2