MCH55 Ceramic capacitors Multi-layer ceramic chip capacitors MCH55 (5750 (2220) size, chip capacitor) zFeatures 1) High capacitance 2) Achieved high capacitance by thin and multi layer technology 3) Lead-free plating terminal 4) No polarity zQuick Reference The design and specifications are subject to change without prior notice. Please check the most recent technical specifications prior to placing orders or using the product. For more detail information regarding packaging style code, please check product designation. zHigh dielectric constant Part No. Size code Temperature characteristics code Operating temp. range (°C) Rated voltage (V) 50 ±10% (B) −25 to +85 25 16 50 CN MCH55 ±15% (R) (X7R) −55 to +125 5750 (2220) 25 16 ±15% (X5R) −55 to +85 +30% , −80% (F) −25 to +85 +22% , −82% (Y5V) −30 to +85 FN 16 6.3 50 25 16 50 25 16 Capacitance (pF) 4,700,000 (E6 Series) 6,800,000 (E6 Series) 10,000,000 (E6 Series) 15,000,000 (E6 Series) 22,000,000 (E6 Series) 4,700,000 (E6 Series) 6,800,000 (E6 Series) 10,000,000 (E6 Series) 15,000,000 (E6 Series) 22,000,000 (E6 Series) 33,000,000 (E6 Series) 47,000,000 (E6 Series) 68,000,000 (E6 Series) 22,000,000 (E3 Series) 47,000,000 (E3 Series) 100,000,000 (E3 Series) 22,000,000 (E3 Series) 47,000,000 (E3 Series) 100,000,000 (E3 Series) Capacitance tolerance K(±10%) M(±20%) Thickness (mm) 2.0 ± 0.2 2.5 ± 0.3 2.0 ± 0.2 2.3 ± 0.2 2.5 ± 0.3 2.0 ± 0.2 2.5 ± 0.3 2.0 ± 0.2 2.3 ± 0.2 2.5 ± 0.3 2.0 ± 0.2 2.3 ± 0.2 2.0 ± 0.2 Z(+80% , −20%) 2.5 ± 0.3 2.0 ± 0.3 2.5 ± 0.3 zExternal dimensions (Unit : mm) Product thickness(mm) 0.2Min. T 2.0±0.2 2.3±0.2 2.5±0.3 T 5.7±0.4 5.0±0.4 1/9 MCH55 Ceramic capacitors zProduct designation Packing specification Reel Basic ordering unit (pcs.) P 2.0mm Plustic tape (width 8mm, pitch 4mm) φ180mm (7in.) 500 P 2.3mm Plustic tape (width 8mm, pitch 4mm) φ180mm (7in.) 500 P 2.5mm Plustic tape (width 8mm, pitch 4mm) φ180mm (7in.) 500 Code Product thickness Reel (φ180mm) : compatible with EIAJ ET-7200A Packing Style Part No. M C H 5 5 Rated voltage Code Voltage 8 6.3V 4 10V 3 16V 2 25V 5 50V 3 F N 1 0 7 Temperature characteristic code : Refer to quick reference table. Z P Nominal capacitance 3-digit designation according to IEC Capacitance tolerance Code Tolerance M ±10% ±20% Z +80%, −20% K zPerformance and test method No. Items Performance Test Method (As per JIS C 5101-1, JIS C 5101-10) 1 Appearance and dimensions No marked defects shall be allowed As per 4.4 of JIS C 5101-1. As per 4.5 of JIS C 5101-10 for appearance. Dimensions shall be as specified the Using a Magnifier. clause 4. 2 Withstanding voltage No dielectrical breakdown or other damage shall be allowed. As per 4.6 of JIS C 5101-1. As per 4.6.4 of JIS C 5101-10 Voltage shall be applied as per Table1. Table 1 CharacVoltage teristic CN 250% Rated voltage FN Voltage shall be applied for 1 to 5s with 50mA charging and discharging current. 3 Insulation resistance Not less than 10000MΩ or 100MΩ µF, whichever is less. As per 4.5 of JIS C 5101-1. As per 4.6.3 of JIS C 5101-10 Measurements shall be made after 60+/−5s period of the rated voltage applied. 4 Capacitance Capacitance shall be within specified tolerance range. As per 4.7 of JIS C 5101-1. As per 4.6.1 of JIS C 5101-10 Measurements shall be made under the conditions specified in Table 2. Table 2 Frequency Voltage Characteristic CN FN 5 Dielectric loss tangent CN tan δ < − 7.5% FN Rated voltage=16V tan δ < − 10.0% < − 10µF > 10µF 1+/−0.1kHz 120+/−24Hz 1+/−0.2Vrms. 0.5+/−0.2Vrms. As per 4.8 of JIS C 5101-1. As per 4.6.2 of JIS C 5101-10 Measurements shall be made under the conditions specified in Table 2. 2/9 MCH55 Ceramic capacitors No. Items 6 Temperature characteristic Performance CN FN B +/−10% (−25°C to +85°C) X5R +/−15% (−55°C to +85°C) Test Method (As per JIS C 5101-1, JIS C 5101-10) As per 4.24 of JIS C 5101-1. As per 4.7 of JIS C 5101-10 If required, measurements shall be made at a given temperature. +30%, −80% (−25°C to +85°C) +22%, −82% (−30°C to +85°C) 7 Solderability More than 3/4 of each end termination shall be covered with new solder. As per 4.15.2 of JIS C 5101-1. As per 4.11 of JIS C 5101-10 The solder specified in JIS Z 3282 H63A shall be used. Ans the flux containing 25% rosin and ethanol solution shall be used. The specimens shall be immersed into the solder at 235+/−5°C for 2+/−0.5s So that both end terminations are completely under solder. 8 Resistance Appearance to soldering heat Without mechanical damage. As per 4.14 of JIS C 5101-1. As per 4.10 of JIS C 5101-10 The solder specified in JIS Z 3282. H63A shall be used. The specimens shall be immersed into the solder at 260+/−5°C for 5+/−0.5s so that both end terminations are completely under the solder. Pre-heating at 150+/−10°C for 1 to 2min Initial measurements prior to test shall be performed after the thermal Pre-conditioning specified in Remarks (1). Final measurements shall be made after the specimens have been left at room temperature as per Table3. Change rate from initial value CN Within +/−7.5% FN Within +/−20% Dielectric loss tangent Within specified initial value. Insulation resistance Within specified initial value. Withstanding No defects shall be allowed. voltage 9 End termination adherence Without peeling or sign of peeling shall be allowed on the end terminations. Table3 Characteristic CN, FN Time 48+/−4 h As per 4.13 of JIS C 5101-1. As per 4.8 ofJIS C 5101-10 A 5N weight for 10+/−1s shall be applied to the soldered specimens as shown by the arrow mark in the below sketch. Applied pressure Substrate Capacitor 3/9 MCH55 Ceramic capacitors No. Items Performance Test Method (As per JIS C 5101-1, JIS C 5101-10) 10 Bending strength Appearance Without mechanical damage. As per 4.35 of JIS C 5101-1. As per 4.9 of JIS C 5101-10 Glass epoxy board with soldered specimens shall be bent till 1mm by 1.0mm/s. 11 Vibration Appearance Without mechanical damage. As per 4.17 of JIS C 5101-1. The specimens shall be soldered on the specified test jig. Initial measurements shall be made after the thermal pre-conditioning specified in Remarks(1). Final measurements shall be made after the specimens have been left at room temperature as per Table3. [Condition] Directions : 2h each X, Y and Z directions Total : 6h Frequency range : 10 to 55 to 10Hz(1min) Applitude : 1.5mm (shall not exceed acceleration196m/s2) Change rate from initial value Dielectric loss tangent CN Within +/−7.5% FN Within +/−20% Within specified initial value. Table3 Characteristic CN, FN 12 Temperature Appearance cycling Change rate from initial value Dielectric loss tangent Insulation resistance Without mechanical damage. CN Within +/−7.5% FN Within +/−20% Within specified initial value. Within specified initial value. Withstanding No defects shall be allowed. voltage Time 48+/−4 h As per 4.16 of JIS C 5101-1 As per 4.12 of JIS C 5101-10 The specimens shall be soldered on the test jig shown in Remarks. Temperature cycle : 100cycles Initial measurements prior to test shall be performed after the thermal per-conditioning specified in Remarks (1). Final measurements shall be made after the specimens have been left at room temperature as per Table3. Test condition Step Temp. (°C) Time (min) 1 Min operating temp. 2 Room temp. 30+/−3 < −3 3 Max operating temp. 4 Room temp. 30+/−3 < −3 Table3 Characteristic CN, FN Time 48+/−4 h 4/9 MCH55 Ceramic capacitors No. 13 Humidity (Steady) Items Performance Appearance Without mechanical damage. Change rate from initial value CN FN Dielectric tangent CN FN Insulation resistance 14 Humidity life test Test Method (As per JIS C 5101-1, JIS C 5101-10) As per 4.22 of JIS C 5101-1 As per JIS C 5101-10 Test temperature : 60+/−2°C Within +/−12.5% Relative humidity : 90 to 95% Test time : 500 +24/−0 h Initial measurements prior to test shall Within +/−30% be made after the voltage pre-conditioning specified in Less than 200% of Remarks (2). initial spec. Final measurements have been left at room temperature as per Table3. Less than 150% of initial spec. Table3 Not less than 1000MΩ or 10MΩ µF, whichever is less. Characteristic CN, FN Time 48+/−4 h Appearance Without mechanical damage. Change rate from initial value Dielectric loss tangent Insulation resistance As per 4.22 of JIS C 5101-1 As per 4.14 of JIS C 5101-10 CN Within +/−12.5% Test temperature : 60+/−2°C Relative humidity : 90 to 95% Voltage : Rated voltage FN Within +/−30% Test time : 500 +24/−0 h Less than 200% of Initial measurements prior to test shall CN be made after the voltage initial spec. pre-conditioning specified in Less than 150% of Remarks (2). FN initial spec. Final measurements shall be made after the specimens have been left at room Not less than 500MΩ or temperature as per Table3. 5MΩ µF, whichever is less. Table3 Characteristic CN, FN Time 48+/−4 h 5/9 MCH55 Ceramic capacitors No. Items 15 Heat life test Performance Appearance Without mechanical damage. Change rate from initial value Dielectric loss tangent Insulation resistance CN Within +/−15% FN Within +/−30% CN Less than 200% of initial spec. FN Less than 150% of initial spec. Not less than 1000MΩ or 10MΩ µF, whichever is less. Test Method (As per JIS C 5101-1, JIS C 5101-10) As per 4.23 of JIS C 5101-1. As per 4.15 of JIS C 5101-10 Test Voltage temperature(°C) CN 85 (B X5R) FN 85 200% Rated voltage 200% Rated voltage Test time (h) 1000 +48/−0 1000 +48/−0 Initial measurements prior to test shall be made after the voltage pre-conditioning specified in Remarks (2). Final measurements shall be made after the specimens have been left at room temperature Table3 Characteristic CN, FN Time 48+/−4 h [Remarks] Pre-conditioning If specified in test method of as per 3(Performance and test method), capacitors of CN, FN characteristics shall be pre-conditionded as follows. (1) Thermal pre-conditioning Prior to initial measurements, specimens shall be conditioned at a temperature of 150 0/−10°C for a period of 1hr., and shall be allowed to stabilize at room temperature for 48+/−4h (2) Voltage pre-conditioning Prior to initial measurements, voltage specified as a test condition shall be applied to specimens for a period of 1hr., and the specimens shall be allowed to stabilize at room temperature for 48+/−4h <Test jig> Soldering Glass epoxy substrate 6/9 MCH55 Ceramic capacitors zPackaging specifications Taping dimensions Reel dimensions t φJ E A D G t1 H P : Plastic tape Pulling direction C Symbol D φ13.0 + − 0.2 F E H G F t J t1 Plastic 5.5 1.75 8.0 2.0 4.0 φ1.5 Dimensions 12.0 +/ −0.3 +/ −0.05 +/ −0.1 +/ −0.1 +/ −0.05 +/ −0.1 +0.1/ −0 0.6 MAX. 6.5 MAX. (Unit : mm) Symbol Style A Label pasting As per EIAJ ET−7200A (Unit : mm) B 5.4 MCH55 14.0 + − 1.5 Pulling direction +0 φ180 −1.5 C φ60.0+1.0 −0 B 6.1 (Unit : mm) (1) The quantity for one reel is as bellows. Kind of reel Series φ180 reel MCH55 Plastic tape Quantity Symbol 500 pcs. P (2) When the tape is pulled out towards the operator with the cover tape facing upward, the feeding holes shall be found on the right portion of the tape. (3) Specification of beginning and ending of the tape are as follows. Ending(reel's center) Beginning(reel's round) : Approx. Over 160mm (no chips) : Approx. Over 160mm (no chips) : Approx. 240mm (cover tape only) (4) No juncture of tape shall be allowed. (5) The share strength of tape shall be more than 5N at the break down strength. (6) The peel strength of the cover tape shall be 0.1 to 0.7(N) when the cover tape are peeled 0 to 15 degree from the surface. (7) The number of missing components shall not exceed 0.1% of the total number of components (marked number) or one whichever is the larger, and no consecutive missing exceeding two is allowed. (8) The reels made from resin shall be used, as per EIAJ ET-7200A. zMarking No marking shall be performed on the chip. Trademark, parts number, quantity, lot No. , and country of origin shall be labeled on each reel. zNumbering system for LOT No. Example 03 (1) 01 (2) A0001 (3) F (4) (1) The end of the Christian Era < two digits> of production finish. (2) Week in completing part of production finish. (3) Manufacture continuity number. (4) The symbol of manufacturing plant. 7/9 MCH55 Ceramic capacitors zLabel expression The Figure below is label expression < Label Example > Part Number : MCH553CN226MP ① ② ③ ④ ⑤ ⑥ ⑦ ⑧ Part Number Division cord Quantity Lot No. The Country of origin Inspector QR code Trademark zPacking method 1) φ180mm Reel EIAJ cole B' 2 C' (reel) Label A' [width of 9mm : 5reel] 1 A (interior box of R-26) Packing slip B C (R-26) 8/9 MCH55 Ceramic capacitors < Packaging unit > Symbol Quantity of reel in interior box Quantity of reel in box of R-26 K Dimensions R-26 3 12 Packaging interior box of R-26 A (A’) 195 185 B (B’) 255 60 C (C’) 190 185 (Unit : mm) < Appearance > Carton < Accumulation > You must do accumulation by ten boxes < Packaging slip > 1. 2. 3. 4. 5. Customer Parts number Quantity Box quantity Trade mark 9/9 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of with would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. About Export Control Order in Japan Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control Order in Japan. In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause) on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction. Appendix1-Rev1.1