Shoulder HDF110NS3 This specification shall cover the characteristics of saw filter with f110ns3 used for the page system. Datasheet

规格书编号
SPEC NO :
产品 规 格书
SPECIFICATION
CUSTOMER 客 户:
PRODUCT 产 品:
SAW FILTER
MODEL NO 型 号:
HDF110N SMD-3
MARKING 印 字:
HDF101
PREPARED 编 制:
CHECKED 审 核:
APPROVED 批 准:
D A T E 日 期:
2006-5-11
客户确认 CUSTOMER RECEIVED:
审核 CHECKED
批准 APPROVED
日期 DATE
无锡市好达电子有限公司
Shoulder Electronics Limited
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 1 of 9
SAW FILTER
HDF110N
SMD-3
更改历史记录
History Record
更改日期
Date
www.shoulder.cn
规格书编号
Spec. No.
产品型号
Part No.
客户产品型号
Customer No.
Tel:0755-82916880 Fax:0755-82916881
更改内容描述
Modify Content
E-mail:[email protected]
备注
Remark
Page 2 of 9
SAW FILTER
HDF110N
SMD-3
1. SCOP
This specification shall cover the characteristics of SAW filter with F110NS3 used for the page
system.
2. ELECTRICAL SPECIFICATION
DC Voltage VDC
AC Voltage Vpp
Operation temperature
Storage temperature
RF Power Dissipation
10V
10V50Hz/60Hz
-40℃ to +85℃
-45℃ to +85℃
0dBm
2.2Electronic Characteristics
型号
Part Number
中心频率(fo)(MHz)
Nominal Center Frequency
3dB 带宽
Bandwidth(from fo)(KHz)
阻带衰耗
Stop Band Attenuation
(from peak level)(dB)
1)fo-5.0MHz
2)fo-3.5MHz
3)fo+/-1.728MHz
5)fo+3.456MHz
6)fo+5MHz
插入损耗(dB)
Insertion Loss(at minimum loss point)
群延时波动(fo+/-576KHz)(μsce.)
Group Delay Deviation
输入/输出阻抗
Input/output Impedance
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
HDF110N
110.592
+/-576min
50min
45min
30min
40min
40min
4.5max
0.7
300Ω//1.2μH
Page 3 of 9
SAW FILTER
HDF110N
SMD-3
3.DIMENSION
3.Input/output
2. Input or Input ground
1.5. To be ground
6.Output or output ground
4.8. case ground
7. Output/Input
Marking:HDF101
HD: Brand
F : Filter
101 : No.
4.TEST CIRCUIT
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 4 of 9
SAW FILTER
HDF110N
SMD-3
5.Typical Frequency Response
5. ENVIRONMENTAL CHARACTERISTICS
5-1 Temperature cycling
Subject the device to a low temperature of -40℃ for 30 minutes. Following by a
high temperature of +25℃ for 5 Minutes and a higher temperature of +85℃ for 30
Minutes. Then release the device into the room conditions for 1 to 2 hours prior to the
measurement. It shall meet the specifications in 2.2.
5-2 Resistance to solder heat
Submerge the device terminals into the solder bath at 260℃±5℃ for 10±1 sec.
Then release the device into the room conditions for 4 hours. It shall meet the specifications
in 2.2.
5-3 Solderability
Submerge the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than
95% area of the soldering pad must be covered with new solder. It shall meet the
specifications in 2.2.
5-4 Mechanical shock
Drop the device randomly onto the concrete floor from the height of 1 m 3 times. the
filter shall fulfill the specifications in 2.2.
5-5 Vibration
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 5 of 9
SAW FILTER
HDF110N
SMD-3
Subject the device to the vibration for 2 hour each in x,y and z axes with the
amplitude of 1.5 mm at 10 to 55 hz. The filter shall fulfill the specifications in 2.2.
6. REMARK
6.1 Static voltage
Static voltage between signal load & ground may cause deterioration &destruction
of the component. Please avoid static voltage.
6.2 Ultrasonic cleaning
Ultrasonic vibration may cause deterioration & destruction of the component.
Please avoid ultrasonic cleaning
6.3 Soldering
Only leads of component may be soldered. Please avoid soldering another part of
component.
7. Packing
7.1 Dimensions
(1) Carrier Tape: Figure 1
(2) Reel: Figure 2
(3) The product shall be packed properly not to be damaged during transportation and storage.
7.2 Reeling Quantity
1000 pcs/reel 7’’
3000 pcs/reel 13’’
7.3 Taping Structure
(1) The tape shall be wound around the reel in the direction shown below.
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 6 of 9
SAW FILTER
HDF110N
SMD-3
(2) Label
Device Name
User Product Name
Quantity
Lot No.
(3) Leader part and vacant position specifications.
8. TAPE SPECIFICATIONS
8.1 Tensile Strength of Carrier Tape: 4.4N/mm width
8.2 Top Cover Tape Adhesion (See the below figure)
(1) pull off angle: 0~15º
(2) speed: 300mm/min.
(3) force: 20~70g
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 7 of 9
SAW FILTER
HDF110N
SMD-3
[Figure 1] Carrier Tape Dimensions
[Unit:mm]
W
F
E
P0
P1
P2
D0
D1
t1
t2
A
B
12.0
±0.3
5.5
±0.05
1.75
±0.1
4.0
±0.1
8.0
±0.1
2.0
±0.05
Ø1.5
±0.1
Ø1.0
±0.25
0.3
±0.05
2.10
±0.1
6.40
±0.1
5.20
±0.1
[Figure 2]
[Unit:mm]
A
B
C
D
E
W
t
r
Ø330
Ø100
Ø13
Ø21
2
13
3
1.0
www.shoulder.cn
Tel:0755-82916880 Fax:0755-82916881
E-mail:[email protected]
Page 8 of 9
SAW FILTER
±1.0
±0.5
www.shoulder.cn
HDF110N
±0.5
±0.8
±0.5
±0.3
Tel:0755-82916880 Fax:0755-82916881
max.
SMD-3
max.
E-mail:[email protected]
Page 9 of 9
Similar pages