SURFACE MOUNT DISPLAY ATTENTION OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Part Number: ACSC08-51ZGKWA Green Features Descriptions 0.8 inch digit height. The Green source color devices are made with InGaN on Sapphire Light Emitting Diode. Low current operation. Excellent character appearance. Electrostatic discharge and power surge could damage the LEDs. Mechanically rugged. It is recommended to use a wrist band or anti- Gray face, white segment. electrostatic glove when handling the LEDs. Package: 200pcs/ reel Moisture sensitivity level : level 2a. All devices, equipments and machineries must be electrically grounded. RoHS compliant. Package Dimensions& Internal Circuit Diagram GREEN Notes: 1. All dimensions are in millimeters (inches), Tolerance is ±0.25(0.01")unless otherwise noted. 2. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 3. The gap between the reflector and PCB shall not exceed 0.25mm. SPEC NO: DSAO0998 REV NO: V.1A DATE: JAN/07/2015 PAGE: 1 OF 5 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Q.M.Chen ERP: 1351000730 Selection Guide Part No. Dice Green (InGaN) ACSC08-51ZGKWA Iv (ucd) [1] @ 10mA Lens Type White Diffused Description Min. Typ. 52000 118000 *21000 *40000 Common Anode, Rt. Hand Decimal. Units Test Conditions Note: 1.Luminous intensity/ luminous Flux: +/-15%. *Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Device Typ. Max. λpeak Peak Wavelength Green 515 nm IF=20mA λD [1] Dominant Wavelength Green 525 nm IF=20mA Δλ1/2 Spectral Line Half-width Green 35 nm IF=20mA C Capacitance Green 45 pF VF=0V;f=1MHz VF [2] Forward Voltage Green 3.3 4.1 V IF=20mA IR Reverse Current Green 50 uA VR=5V Notes: 1.Wavelength: +/-1nm. 2.Forward Voltage: +/-0.1V. 3.Wavelength value is traceable to the CIE127-2007 compliant national standards. 4.Excess driving current and/or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Green Units Power dissipation 102.5 mW DC Forward Current 25 mA Peak Forward Current [1] 150 mA 5 V Reverse Voltage Operating / Storage Temperature -40°C To +85°C Note: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAO0998 REV NO: V.1A DATE: JAN/07/2015 PAGE: 2 OF 5 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Q.M.Chen ERP: 1351000730 Green ACSC08-51ZGKWA SPEC NO: DSAO0998 REV NO: V.1A DATE: JAN/07/2015 PAGE: 3 OF 5 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Q.M.Chen ERP: 1351000730 ACSC08-51ZGKWA Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.15) Reel Dimension Tape Specifications (Units : mm) SPEC NO: DSAO0998 REV NO: V.1A DATE: JAN/07/2015 PAGE: 4 OF 5 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Q.M.Chen ERP: 1351000730 PACKING & LABEL SPECIFICATIONS ACSC08-51ZGKWA Terms and conditions for the usage of this document 1.The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2.The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3.When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4.The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5.The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6.All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAO0998 REV NO: V.1A DATE: JAN/07/2015 PAGE: 5 OF 5 APPROVED: WYNEC CHECKED: Joe Lee DRAWN: Q.M.Chen ERP: 1351000730