ON NCS2632 Nocap, pop-free, 3 vrms audio line driver with adjustable gain Datasheet

NCS2632
NOCAP], Pop-Free, 3 VRMS
Audio Line Driver with
Adjustable Gain
The NCS2632 is a pop−free stereo line driver. It uses
ON Semiconductor’s patented NOCAP technology which allows the
elimination of the external DC−blocking capacitors by providing
ground−referenced outputs through the generation of an internal
negative supply rail. The device can drive 3 VRMS into a 600 W load at
5 V power supply. By eliminating the two external heavy coupling
capacitors, the NOCAP approach offers significant space and cost
savings compared to similar audio solutions.
The NCS2632 has differential inputs and is available with an
external adjustable gain ranging from ±1 V/V to ±10 V/V. The gain is
adjusted with external resistors. The device can also be configured as a
2nd order low pass filter to complement DAC’s and SOC converters.
In addition to the NOCAP architecture, it contains specific circuitry to
prevent “Pop & Click” noise from occurring during Enable /
Shutdown transitions. The Signal-to-Noise Ratio reaches 105 dB,
offering high fidelity audio sound. The NCS2632 exhibits a high
power supply rejection with a typical value of 90 dB. This device also
features an Under−Voltage Protection (UVP) function which can be
adjusted using an external resistor bridge. The device is available in a
TSSOP−14 package.
http://onsemi.com
MARKING
DIAGRAM
14
14
1
TSSOP−14
CASE 948G
A
L
Y
W
G
1
NCS
2632
ALYWG
G
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
(*Note: Microdot may be in either location)
*For additional marking information, refer to
Application Note AND8473/D.
Features
ORDERING INFORMATION
• NOCAP
See detailed ordering and shipping information in the package
dimensions section on page 13 of this data sheet.
Eliminates Pop/Clicks
Eliminates Output DC−Blocking Capacitors –
Provides Flat Frequency Response 20 Hz – 20 kHz
Supply Voltage from 2.2 V to 5.5 V
Low Noise and THD
♦ SNR = 105 dB
♦ Typical Vn at 8 mVrms, A−Weighted
♦ THD+N < 0.001% at 1 kHz
Output Voltage into 600 W Load
♦ 2 VRMS with 3.3 V Supply Voltage
♦ 3 VRMS with 5 V Supply Voltage
Adjustable Gain from ± 1 V/V to ± 10 V/V
Differential Input
High PSRR: 90 dB
External Under−Voltage Detection Function
Enhanced Pop & Click Suppression Function
Offset Voltage ≤ ±400 mV
♦
♦
•
•
•
•
•
•
•
•
•
© Semiconductor Components Industries, LLC, 2013
October, 2013 − Rev. 4
• Outputs pass ±8 kV contact discharge according to
IEC61000−4−2 under application conditions
• Available in a TSSOP−14 package
• These Devices are Pb−Free, Halogen Free/BFR Free
and are RoHS Compliant
Applications
•
•
•
•
•
1
Set−Top Boxes
PDP / LCD TV
Blu−ray™ Player, DVD Players
Home Theater in a Box
Laptops, Notebook PCs
Publication Order Number:
NCS2632/D
NCS2632
VDD
INLP
INLM
OUTL
EN
CP
CN
Charge
Pump
Circuitry
Click/Pop
Suppression
Circuitry
Bias
Circuitry
AGND
UVP
AGND
PGND
AGND
OUTR
VSS
INRP
INRM
Figure 1. NCS2632, Simplified Block Diagram
1
INRP
INLP
14
2
INRM
INLM
13
3
OUTR
OUTL
12
4
AGND
UVP
11
5
EN
PGND
10
6
VSS
7
CN
VDD
9
CP
8
Figure 2. NCS2632, Pinout
http://onsemi.com
2
NCS2632
PIN FUNCTION AND DESCRIPTION
Pin
Name
Type
1
INRP
Input
Right channel positive input
Description
2
INRM
Input
Right channel negative input
3
OUTR
Output
Right channel output
4
AGND
Ground
Analog ground. Connect to PGND
5
EN
Input
6
VSS
Power
Negative rail output. Connected to ground through 1 mF low ESR ceramic reservoir capacitor.
7
CN
−
Flying capacitor Negative terminal. Connected to CP through 1 mF low ESR ceramic capacitor.
8
CP
−
Flying capacitor Positive terminal. Connected to CN through 1 mF low ESR ceramic capacitor.
9
VDD
Power
Power Supply Input
10
PGND
Ground
Power ground
11
UVP
Input
12
OUTL
Output
13
INLM
Input
Left channel negative input
14
INLP
Input
Left channel positive input
Enable pin. Active High
Under−voltage detection pin.
Left Channel Output
ABSOLUTE MAXIMUM RATINGS (Note 1)
Parameter
Symbol
Value
Unit
VDD
−0.3 to 5.5
V
Input Voltage
VI
VSS – 0.3 to VDD + 0.3
V
Minimum Load Impedance
RL
>600
W
–0.3 to VDD +0.3
V
TJ(max)
−40 to 150
°C
Supply Voltage, VDD to GND
Logic Pin Voltage (EN)
Maximum Junction Temperature
Storage Temperature Range
ESD Capability (Note 2)
Human Body Model
Machine Model
Latch−up Current (Note 3)
Moisture Sensitivity Level (Note 4)
TSTG
−40 to 150
°C
ESDHBM
ESDMM
2000
200
V
ILU
100
mA
MSL
Level 1
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. Refer to ELECTRICAL CHARACTERISTICS and APPLICATION INFORMATION for Safe Operating Area.
2. This device series incorporates ESD protection and is tested by the following methods:
ESD Human Body Model tested per AEC−Q100−002 (JEDEC standard: JESD22−A114)
ESD Machine Model tested per AEC−Q100−003 (JEDEC standard: JESD22−A115)
3. Latch−up Current tested per JEDEC standard: JESD78
4. Moisture Sensitivity Level tested per IPC/JEDEC standard: J−STD−020A
THERMAL CHARACTERISTICS
Parameter
Junction−to−Ambient Thermal Resistance, TSSOP−14 (Note 5)
5. Values based on copper area of 645
mm2
(or 1
in2)
Symbol
Value
Unit
qJA
115
°C/W
of 1 oz copper thickness and FR4 PCB substrate.
RECOMMENDED OPERATING CONDITIONS
Parameter
Symbol
Min
Typ
Max
Unit
VDD
2.2
3.3
5.5
V
High−Level Input Voltage
VIH (EN)
1.2
Low−Level Input Voltage
VIL (EN)
Supply Voltage with UVP connected to Ground
Ambient Temperature
TA
http://onsemi.com
3
−40
V
0.4
V
85
°C
NCS2632
ELECTRICAL CHARACTERISTICS, TA = 25°C (unless otherwise noted)
Parameter
Symbol
Test Conditions
|VOS|
VDD = 2.5 V to 5 V, Voltage follower − gain = 1
High−Level Input Current (EN)
|IIH|
Low−Level Input Current (EN)
Supply Current
Output Offset Voltage
Min
Typ
Max
Unit
100
400
mV
VDD = 5 V, VI = VDD
100
nA
|IIL|
VDD = 5 V, VI = 0 V
100
nA
IDD
VDD = 2.2 V, No load, EN = VDD
7
11
mA
VDD = 5.5 V, No load, EN = VDD
8
11
mA
60
500
nA
Shutdown mode, VDD = 2.2 V to 5.5 V
Under−Voltage Protection (UVP)
Threshold
VUVP
UVP Internal Hysteresis Current Source
IHYS
5
mA
fcp
400
kHz
Charge Pump Frequency
1.25
V
OPERATING CHARACTERISTICS
VDD = 3.3 V, TA = 25°C, RL = 2.5 kW, CVSS = 1 mF, CIN = 10 mF, RIN = 10 kW, Rfb = 20 kW (unless otherwise noted)
Parameter
Symbol
Test Conditions
Min
VO
THD = 1%, VDD = 3.3 V, f = 1 kHz
2.05
THD = 1%, VDD = 5 V, f = 1 kHz
3.05
THD = 1%, VDD = 5 V, f = 1 kHz, RL = 100 kW
3.1
Output Voltage (Outputs In Phase)
Total Harmonic Distortion plus Noise
THD+N
Typ
Max
Unit
Vrms
VO = 2 Vrms, f = 1 kHz
0.001
%
VO = 2 Vrms, f = 10 kHz
0.001
%
dB
Power Supply Rejection
PSRR
VDD = 2.5 V to 5 V
90
Crosstalk
XTALK
VO = 2 Vrms, f = 1 kHz
−120
dB
IO
VDD = 3.3 V
21
mA
Output Current Limit
Input Resistor Range (Note 6)
RIN
1
10
47
kW
Feedback Resistor Range (Note 6)
Rfb
4.7
20
100
kW
Maximum Capacitive Load (Note 6)
COUT
220
pF
Noise Output Voltage
VN
A−weighted
8
mVrms
Signal to Noise Ratio
SNR
VO = 2 Vrms, THD + N = 0.1% A−weighted
filter
105
dB
6. Guaranteed by design.
http://onsemi.com
4
NCS2632
TYPICAL CHARACTERISTICS
VDD = 3.3 V, TA = 25°C, RL = 2.5 kW, CVSS = 1 mF, CIN = 10 mF, RIN = 10 kW, Rfb = 20 kW (unless otherwise noted)
10
0.1
0.01
0.01
0.1
0.0001
10
0.1
1
10
Figure 4. THD+N vs. Output Voltage over
Temperature, RL = 2.5 kW, VDD = 5 V, f = 1 kHz
10
VDD = 2.0 V
VDD = 3.0 V
VDD = 3.3 V
VDD = 4.0 V
VDD = 4.2 V
VDD = 5.0 V
VDD = 5.5 V
0.1
VDD = 2.2 V
VDD = 3.0 V
VDD = 3.3 V
VDD = 3.6 V
VDD = 4.2 V
VDD = 5.0 V
VDD = 5.5 V
1
0.01
0.001
0.1
0.01
0.001
0.01
0.1
0.1
1
0.0001
10
0.01
0.1
1
10
VOUT (V)
VOUT (V)
Figure 5. THD+N vs. Output Voltage over
Supply, RL = 2.5 kW, f = 1 kHz
Figure 6. THD+N vs. Output Voltage over
Supply, RL = 600 W, f = 1 kHz
0.1
VDD = 5 V, VOUT = 3 V
VDD = 3.3 V, VOUT = 2 V
VDD = 2.2 V, VOUT = 1.4 V
VDD = 3.3 V, VOUT = 2.2 V
VDD = 5 V, VOUT = 3.3 V
0.01
THD+N (%)
THD+N (%)
0.01
Figure 3. THD+N vs. Output Voltage over
Temperature, RL = 2.5 kW, VDD = 3.3 V, f = 1 kHz
THD+N (%)
THD+N (%)
1
VOUT (V)
1
0.01
0.001
0.001
0.0001
0.01
VOUT (V)
10
0.0001
0.1
0.001
0.001
0.0001
−40°C
25°C
85°C
125°C
1
THD+N (%)
1
THD+N (%)
10
−40°C
25°C
85°C
125°C
20
200
2000
0.0001
20,000
20
200
2000
20,000
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 7. THD+N vs. Frequency, RL = 2.5 kW
Figure 8. THD+N vs. Frequency, RL = 600 W
http://onsemi.com
5
NCS2632
TYPICAL CHARACTERISTICS
6.00
6.00
5.98
5.98
5.96
5.96
GAIN (dB)
GAIN (dB)
VDD = 3.3 V, TA = 25°C, RL = 2.5 kW, CVSS = 1 mF, CIN = 10 mF, RIN = 10 kW, Rfb = 20 kW (unless otherwise noted)
5.94
VDD = 2.2 V, VOUT = 1.4 V
VDD = 3.3 V, VOUT = 2 V
VDD = 5 V, VOUT = 3 V
5.92
20
200
2000
5.90
20,000
2000
Figure 9. Gain vs. Frequency,
RL = 2.5 kW
Figure 10. Gain vs. Frequency,
RL = 600 W
−20
−20
−40
−40
−60
−80
−100
20,000
−60
−80
−100
−120
−120
20
200
2000
−140
20,000
2000
Figure 11. Crosstalk vs. Frequency,
RL = 2.5 kW, VDD = 3.3 V, VO = 2 Vrms
Figure 12. Crosstalk vs. Frequency,
RL = 2.5 kW, VDD = 5 V, VO = 2 Vrms
0
100
−20
80
−40
60
40
200
20,000
VDD = 2.2 V
VDD = 3.3 V
VDD = 5 V
−60
−80
−100
VDD = 5 V, VOUT = 3 Vrms
VDD = 3.3 V, VOUT = 2 Vrms
20
200
FREQUENCY (Hz)
120
20
20
FREQUENCY (Hz)
PSRR (dB)
SNR (dB)
200
FREQUENCY (Hz)
0
0
20
FREQUENCY (Hz)
0
−140
VDD = 3.3 V, VOUT = 2 V
VDD = 5 V, VOUT = 3 V
5.92
CROSSTALK (dB)
CROSSTALK (dB)
5.90
5.94
2000
−120
20,000
20
200
2000
20,000
FREQUENCY (Hz)
FREQUENCY (Hz)
Figure 13. Signal−to−Noise Ratio vs.
Frequency, RL = 2.5 kW
Figure 14. Power Supply Rejection Ratio vs.
Frequency, RL = 2.5 kW
http://onsemi.com
6
NCS2632
TYPICAL CHARACTERISTICS
VDD = 3.3 V, TA = 25°C, RL = 2.5 kW, CVSS = 1 mF, CIN = 10 mF, RIN = 10 kW, Rfb = 20 kW (unless otherwise noted)
6
5
8.0
4
7.5
⎢VSS⎜ (V)
SUPPLY CURRENT (mA)
8.5
7.0
2
VDD = 2.2 V
VDD = 3.0 V
VDD = 5.0 V
VDD = 5.5 V
6.5
6.0
−40
25
3
1
0
−50
85
VDD = 3.3 V
VDD = 5 V
−25
0
25
50
75
100
TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 15. Quiescent Current vs. Temperature,
No Load, VI = 0 V, EN = High
Figure 16. VSS vs. Temperature
EN
tOFF ≈ 80 ms
EN
tON ≈ 650 ms
OUT
OUT
VSS
VSS
Figure 18. Shutdown Turn−Off Time,
RL = 2.5 kW, VDD = 5 V
Figure 17. Startup Turn−On Time, RL = 2.5 kW,
VDD = 5 V
EN
EN
tOFF ≈ 100 ms
OUT
tON ≈ 550 ms
OUT
VSS
VSS
Figure 20. Shutdown Turn−Off Time,
RL = 2.5 kW, VDD = 3.3 V
Figure 19. Startup Turn−On Time, RL = 2.5 kW,
VDD = 3.3 V
http://onsemi.com
7
125
NCS2632
APPLICATION INFORMATION
DESCRIPTION
disable, contributing this way to eliminate potential source
of pop noise.
The device shuts down when the UVP voltage goes below
1.25 V typically. To monitor the lower main power supply
limit, an external voltage divider constituted with three
resistors, RUP, RDW and RHYS is used (Figure 21).
Resistors values have to be chosen based on the requested
power supply shutdown threshold and hysteresis for a given
application. It is recommended to have RHYS >> RDW //
RUP. RHYS is optional in the case where hysteresis is not
necessary.
The NCS2632 is a stereo line driver with a NOCAP
architecture. This architecture eliminates the need to use two
large, external capacitors required by conventional audio
line driver applications. The NCS2632 is basically
composed of two true ground amplifiers with internal power
supply rail, one UVP−circuit block, and short−circuit
protection. The gain of the NCS2632 can be adjusted with
two external resistors.
The NOCAP approach is a patented architecture that
requires only two 1 mF low ESR ceramic capacitors (fly
capacitor and reservoir capacitor). It generates a
symmetrical positive and negative voltage and it allows the
output of the amplifiers to be biased around the ground (True
Ground).
The NCS2632 includes a special circuitry for eliminating
any pop and click noise during turn on and turn off time. This
circuitry combined with the true ground output architecture
and a trimmed output offset voltage makes the elimination
of pop and click particularly efficient.
Board Main
Power Suppply
IHYS
RUP
On/Off
UVP
PVDD
RHYS
Vn
UNDER−VOLTAGE PROTECTION (UVP) PIN
MANAGEMENT
RDW
The UVP pin can be used to shut down the audio line
driver by monitoring the board’s main power supply. Then
the line driver can be shut down before upstream devices
Figure 21. Voltage Divider Connected to UVP for
Power Supply Monitoring
http://onsemi.com
8
NCS2632
When the resistor divider is connected to the pin UVP as shown in Figure 21, the UVP pin voltage is a function of PVDD
and IHYS according to the below equation:
V UVP + PVDD
With VUVPth = 1.25 V and IHYS = 5 mA
ǒ
RDW
RDW
) RHYS
RDW ) RUP
RUP
RDW ) RUP
Ǔ
I HYS
(eq. 1)
This gives a PVDD Shutdown threshold.
PVDD Shutdown Threshold:
PVDD SD + V UVPth
RDW ) RUP
RDW
RUP
ǒRHYS ) RDW
Ǔ
RDW ) RUP
* I HYS
RDW ) RUP
RDW
(eq. 2)
Simplified PVDD Shutdown threshold assuming RHYS >> RDW // RUP:
PVDD SD + ǒV UVPth * I HYS
RDW ) RUP
RHYSǓ
(eq. 3)
RDW
The PVDD Startup threshold is given by the below equation.
PVDD Hysteresis:
RDW ) RUP
PVDD UP + V UVPth
(eq. 4)
RDW
The hysteresis component is:
PVDD Hysteresis:
RUP
ǒRHYS ) RDW
Ǔ
RDW ) RUP
DPVDD + V HYS + I HYS
+ I HYS
ǒRHYS ) RDWRDWRUP ) RUPǓ
RDW ) RUP
RDW
PVDD UP
(eq. 5)
V UVPth
Simplified PVDD Hysteresis assuming RYS >> RDW // RUP:
DPVDD + V HYS + I HYS
RHYS
RDW ) RUP
RDW
For a given PVDD threshold RUP will be a function of RDW.
RUP and RDW:
RUP +
ǒ
PVDD UP
V UVPth
Ǔ
*1
+ I HYS
RYS
RDW
PVDD UP
V UVPth
(eq. 6)
(eq. 7)
According to Equation 6, assuming RHYS >> RDW // RUP, and for a given hysteresis VHYS and PVDD threshold, RHYS is:
RHYS
RHYS +
V HYS
I HYS
V UVPth
PVDD UP
+
1.25
5 mA
V HYS
PVDD UP
For example, to get PVDDSD = 2.5 V and 0.625 V hysteresis,
Power Divider Resistors have to be: RUP = 1.5 kW, RDW = 1 kW and RHYS = 51 kW
http://onsemi.com
9
(eq. 8)
NCS2632
GAIN SETTING RESISTOR SELECTION (RIN and RFB)
A closed−loop gain in the range of 1 to 10 is recommended
to optimize overall system performance.
Selecting values that are too low requires a relatively large
input ac-coupling capacitor, CIN. Selecting values that are
too high increases the overall noise of the amplifier.
RIN and RFB set the closed−loop gain of the amplifier. The
resistor values have to be chosen so that amplifier stability
is preserved. A low gain configuration (close to 1)
minimizes the THD + noise values and maximizes the signal
to noise ratio.
RFB
Vin−
CIN
RIN
Av +
Vin+
CIN
Vout
Vin+ * Vin−
+
R FB
R in
(eq. 9)
Vout
RIN
RFB
Figure 22. Differential Input Gain Configuration
R FB
CIN
R IN
Vin−
Av +
Vout
Vin−
+
−R FB
R IN
(eq.
10)
Vout
Figure 23. Inverting Gain Configuration
CIN
Vin+
Rx
Av +
Vout
RFB
RIN
CIN
Figure 24. Non−Inverting Gain Configuration
http://onsemi.com
10
V out
Vin+
+1)
R FB
R IN
(eq. 11)
NCS2632
Table 1. RECOMMENDED RESISTOR VALUES
Input Resistor Value, RIN
Feedback Resistor Value, RFB
Differential Input Gain
Inverting Input Gain
Non Inverting Input
Gain
22 kW
22 kW
1.0 V/V
–1.0 V/V
2.0 V/V
22 kW
33 kW
1.5 V/V
–1.5 V/V
2.5 V/V
33 kW
68 kW
2.06 V/V
–2.06 V/V
3.1 V/V
100 kW
10.0 V/V
–10.0 V/V
11.0 V/V
10 kW
INPUT CAPACITOR
THD+N. Use a X5R / X7R ceramic capacitor and place it
close to the VDD pin. A value of 1mF is recommended. For
filtering lower frequency noise signals, a 10 mF or greater
capacitor placed near the audio power amplifier would also
help.
The input coupling capacitor blocks the DC voltage at the
amplifier input terminal. This capacitor creates a high−pass
filter with RIN. The size of the capacitor must be large
enough to couple at low frequencies without severe
attenuation in the audio bandwidth (20 Hz − 20 kHz).
The cut off frequency for the input high−pass filter is:
fc +
1
2pR inC in
SHUTDOWN FUNCTION
The device enters shutdown mode when Enable signal is
low. During the shutdown mode, the internal charge pump
is shut down, and the DC quiescent current of the circuit does
not exceed 500 nA. The output is pulled to ground through
a low output impedance of about 40 ohms.
(eq. 12)
A fc < 20 Hz is recommended.
CHARGE PUMP CAPACITOR SELECTION
USING THE NCS2632 AS A 2nd ORDER FILTER
It is recommended to use ceramic capacitors with low
ESR for better performances. X5R or X7R capacitors are
recommended. The flying capacitor Cfly (1 mF) serves to
transfer charge during the generation of the negative
voltage. The VSS reservoir capacitor CVSS must be equal at
least to the Cfly capacitor to allow maximum charge transfer.
The 1 mF capacitors have to be connected as close as
possible to the corresponding pins.
Lower value capacitors can be used but the device may not
operate to specifications.
Audio DACs can require an external low-pass filter to
remove out-of-band noise. This is possible with the
NCS2632, which can be used as a standard Operational
Amplifier with the advantage of better performances
including “pop & click” noise behavior.
Single-ended and differential topologies can be
implemented. In Figures 25 and 26, a Multiple-FeedBack
(MFB) topoplogy, with differential inputs and single-ended
inputs is shown. The two topologies use AC-Coupling
capacitors (CIN) to block the DC-signal component coming
from the source; they contribute to reducing the output offset
voltage.
POWER SUPPLY DECOUPLING CAPACITORS
The NCS2632 is a True Ground amplifier that requires an
adequate decoupling capacitor on VDD to reduce noise and
R FB
C IN
RIN
CINT
RINT
Vin−
C DIFF
Vout
Vin+
CIN
RIN
RINT
CINT
RFB
Figure 25. 2nd Order Active Low Pass Filter − Differential Input
http://onsemi.com
11
NCS2632
RFB
C IN
R IN
C INT
RINT
Vin−
CT
Vout
Figure 26. 2nd Order Active Low Pass Filter − Inverting Input
INITIALIZATION AND POP−FREE POWER UP/DOWN
Pop−free power−up/−down is ensured by keeping EN
(Enable pin) low during power supply ramp−up or
ramp−down. The EN pin should be kept low until the input
ac−coupling capacitors are fully charged before asserting
the EN pin high; this way, proper pre−charge of the
ac−coupling is performed, and pop−free power−up is
achieved. Figure 27 illustrates the preferred sequence.
For an on/off/on power sequence, VDD is required to be
ramped down to 0 V before ramping back up for power on
(shown in Figure 27). This ensures that the NCS2632
internal circuits are properly initialized to guarantee an
optimal output.
+VDD
VDD
Ramp−up
VDD
Supply
VDD
Ramp−down
0V
EN
0V
Internal VSS
Supply
(Negative Rail)
VSS
VSS
−VDD
Dtcharge
Dtdischarge
AC−coupled
Input Capacitor
Pre−Charge Time
Capacitor
Discharge
Figure 27. Initialization and Power Up/Down Sequence
CAPACITIVE LOAD
ESD PERFORMANCE
The NCS2632 has the ability to drive a high capacitive
load up to 220 pF directly. Higher capacitive loads can be
accepted by adding a series resistor of 10 W or larger.
From the system level perspective, the outputs of the
NCS2632 are rated to Level 4 of the IEC61000−4−2 ESD
standard. Using the contact discharge method, the outputs
pass a ±8 kV discharge with an RC network of R = 33 ohms
and C = 1 nF at each output to simulate the application
environment.
http://onsemi.com
12
NCS2632
APPLICATION SCHEMATIC
C1
R1
LEFT
INPUT C1
R1
−
R3
R2
C2
R2
C3
+
C3
R3
INLP
INLM
1mF
LEFT
OUTPUT
Regulated VDD
3.3V/5.0 V
OUTL
EN
ENABLE
RUP
CP
Charge
Pump
Circuitry
1mF
CN
Click/Pop
Suppression
Circuitry
Bias
Circuitry
AGND
AGND
Board Main
Power Suppply
UVP
RDW
PGND
OUTR
AGND
VSS
RIGHT
OUTPUT
1mF
C3
−
C1
R1
RIGHT
INPUT
+
INRP INRM
R3
C1
R1
C3
R2
C2
R2
R3
R1 = R2 = R3 = 5.6 kW, C1 = 100 nF, C2 = 470 pF, C3 = 220 pF
Figure 28. Application Schematic
ORDERING INFORMATION
Device
NCS2632DTBR2G
Package
Shipping†
TSSOP−14
(Pb−Free)
2500 / Tape & Reel
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
http://onsemi.com
13
NCS2632
PACKAGE DIMENSIONS
TSSOP−14
CASE 948G
ISSUE B
14X K REF
0.10 (0.004)
0.15 (0.006) T U
M
T U
V
S
S
S
N
2X
14
L/2
0.25 (0.010)
8
M
B
−U−
L
PIN 1
IDENT.
N
F
7
1
0.15 (0.006) T U
NOTES:
1. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: MILLIMETER.
3. DIMENSION A DOES NOT INCLUDE MOLD
FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH OR GATE BURRS SHALL NOT
EXCEED 0.15 (0.006) PER SIDE.
4. DIMENSION B DOES NOT INCLUDE
INTERLEAD FLASH OR PROTRUSION.
INTERLEAD FLASH OR PROTRUSION SHALL
NOT EXCEED 0.25 (0.010) PER SIDE.
5. DIMENSION K DOES NOT INCLUDE DAMBAR
PROTRUSION. ALLOWABLE DAMBAR
PROTRUSION SHALL BE 0.08 (0.003) TOTAL
IN EXCESS OF THE K DIMENSION AT
MAXIMUM MATERIAL CONDITION.
6. TERMINAL NUMBERS ARE SHOWN FOR
REFERENCE ONLY.
7. DIMENSION A AND B ARE TO BE
DETERMINED AT DATUM PLANE −W−.
S
DETAIL E
K
A
−V−
ÉÉÉ
ÇÇÇ
ÇÇÇ
ÉÉÉ
ÇÇÇ
K1
J J1
DIM
A
B
C
D
F
G
H
J
J1
K
K1
L
M
SECTION N−N
−W−
C
0.10 (0.004)
−T− SEATING
PLANE
D
H
G
DETAIL E
SOLDERING FOOTPRINT*
7.06
1
0.65
PITCH
14X
0.36
14X
1.26
DIMENSIONS: MILLIMETERS
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
14
MILLIMETERS
MIN
MAX
4.90
5.10
4.30
4.50
−−−
1.20
0.05
0.15
0.50
0.75
0.65 BSC
0.50
0.60
0.09
0.20
0.09
0.16
0.19
0.30
0.19
0.25
6.40 BSC
0_
8_
INCHES
MIN MAX
0.193 0.200
0.169 0.177
−−− 0.047
0.002 0.006
0.020 0.030
0.026 BSC
0.020 0.024
0.004 0.008
0.004 0.006
0.007 0.012
0.007 0.010
0.252 BSC
0_
8_
NCS2632
NOCAP is a trademark of Semiconductor Components Industries, LLC (SCILLC).
Blu−ray and Blu−ray Disc are trademarks of Blu−ray Disc Association.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC owns the rights to a number of patents, trademarks,
copyrights, trade secrets, and other intellectual property. A listing of SCILLC’s product/patent coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. SCILLC
reserves the right to make changes without further notice to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any
particular purpose, nor does SCILLC assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. “Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications
and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC
does not convey any license under its patent rights nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for
surgical implant into the body, or other applications intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where
personal injury or death may occur. Should Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and
its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly,
any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture
of the part. SCILLC is an Equal Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5817−1050
http://onsemi.com
15
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
NCS2632/D