规格书编号 SPEC NO : 产品规格书 SPECIFICATION CUSTOMER 客 户： PRODUCT 产 品： MODEL NO 型 号： SAW FILTER HDBF09224A63 SF6-3 PREPARED 编 制： CHECKED 审 核： APPROVED 批 准： D A T E 日 期： 2009-7-23 客户确认 CUSTOMER RECEIVED: 审核 CHECKED 批准 APPROVED 日期 DATE 无锡市好达电子有限公司 Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 1 of 6 SAW FILTER HDBF09224A63 SF6-3 更改内容描述 Modify Content 备注 Remark 更改历史记录 History Record 更改日期 Date www.shoulder.cn 规格书编号 Spec. No. 产品型号 Part No. 客户产品型号 Customer No. Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 2 of 6 SAW FILTER HDBF09224A63 SF6-3 1. SCOPE This specification shall cover the characteristics of SAW filter BF09224A63 2. ELECTRICAL SPECIFICATION DC Voltage VDC AC Voltage Vpp Operation temperature Storage temperature RF Power Dissipation 10V 10V50Hz/60Hz -40℃ to +85℃ -45℃ to +85℃ 10dBm 2.2 Electronic Characteristics Parameter Center Frequency Insertion Loss -1.5dB Bandwidth -3.0dB Bandwidth -15dB Bandwidth -40dB Bandwidth -50dB Bandwidth Passband Variation Absolute Delay Group Delay Variation Ultimate Rejection Material Temperature coef Ambient Temperature www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 Min 91.9 24.0 50 Typ 92.1 28 24.1 24.4 25.1 25.6 25.8 0.8 2.6 70 55 -6.9 25 Max 92.3 32 E-mail:[email protected] 25.3 26.2 1.5 2.7 Units MHz dB MHz MHz MHz MHz MHz dB usec nsec dB KHz/℃ ℃ Page 3 of 6 SAW FILTER HDBF09224A63 SF6-3 2.3 Typical frequency response 3. DIMENSION www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 4 of 6 SAW FILTER HDBF09224A63 SF6-3 4.TEST CIRCUIT ENVIRONMENTAL CHARACTERISTICS 5-1 High temperature exposure Subject the device to +85℃ for 16 hours. Then release the filter into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in 2.2. 5-2 Low temperature exposure Subject the device to -40℃ for 16 hours. Then release the device into the room conditions for 24 hours prior to the measurement. It shall fulfill the specifications in 2.2. 5-3 Temperature cycling Subject the device to a low temperature of -40℃for 30 minutes. Following by a high temperature of +85℃ for 30 Minutes. Then release the device into the room conditions for 24 hours prior to the measurement. It shall meet the specifications in 2.2. 5-4 Resistance to solder heat Dip the device terminals no closer than 1.5mm into the solder bath at 260℃ ±10℃ for 10±1 sec. Then release the device into the room conditions for 4 hours. The device shall meet the specifications in 2.2. 5-5 Solderability Subject the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95% area of the terminals must be covered with new solder. It shall meet the specifications in 2.2. 5-6 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1m 3 times. the device shall fulfill the specifications in 2.2. 5-7 Vibration Subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 Hz. The device shall fulfill the specifications in 2.2. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 5 of 6 SAW FILTER HDBF09224A63 SF6-3 6. REMARK 6.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 6.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 6.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 6 of 6