Automotive Grade AUIR33402S PROTECTED HIGH SIDE SWITCH FOR AUTOMOTIVE DC MOTOR DRIVE Features Product Summary Rds(on)@25°C 3.5m max. Max current 33A Operating voltage 6 – 18V Up to 20Khz PWM switching capability Charge pump for DC operation Active Dv/Dt control Load current feedback Short-circuit protection Programmable over current shutdown Over temperature shutdown Under voltage shutdown Gnd, IN and bootstrap pin loss protection E.S.D protection Low power mode Leadfree, RoHS compliant Automotive qualified* Application Fan engine cooling Air conditioning blower Pumps (oil, fuel, water…) Compressor Package Description D2Pak - 7 leads The AUIR33402S is a 7 terminals high side switch for variable speed DC motor. It features simplify the design of the DC motor drive with a microcontroller. The Mosfet switches the power load proportionally to the input signal duty cycle at the same frequency and provides a current feedback on the Ifbk pin. The over-current shutdown is programmable from 10A to 33A. Over-current and over-temperature latch OFF the power switch, providing a digital diagnostic status on the input pin. In sleep mode, the device consumes less than 10uA. Further integrated protections such as ESD, GND and Cboot disconnect protection guarantee safe operation in harsh conditions of the automotive environment. Ordering Information Base Part Number Standard Pack Form Quantity Tube 50 AUIR33402S Tape and reel left 800 AUIR33402STRL AUIR33402S D2Pak-7-Leads 1 © 2014 International Rectifier www.irf.com Complete Part Number Package Type Submit Datasheet Feedback August 14, 2014 AUIR33402S Automotive Grade Qualification Information Automotive (per AEC-Q100) Comments: This family of ICs has passed an Automotive qualification. IR’s Industrial and Consumer qualification level is granted by extension of the higher Automotive level. Qualification Level Moisture Sensitivity Level ESD † † 7L-DDPAK MSL1, 260°C (per IPC/JEDEC J-STD-020) Machine Model Class M3 (per AEC-Q-100-003) Human Body Model Class H2 (per AEC-Q-100-002) Charged Device Model Class C5 (per AEC-Q-100-011) RoHS Compliant Yes Qualification standards can be found at International Rectifier’s web site http://www.irf.com/ 2 www.irf.com © 2014 International Rectifier Submit Datasheet Feedback August 14, 2014 AUIR33402S Automotive Grade Design: basic schematic with micro-processor The basic circuit is giving all the functionality to drive a motor up to 33A DC. RIfbk set both the level current shutdown and the current feedback reading scale. The IN signal provides to the AUIR33402S the Pwm duty cycle. D1 is the free wheeling diode during PWM operation. As the equivalent circuit between Vbat and – Mot is 2 diode in series (the body diode of the AUIR33402S and D1), the system requires T1, D2, R1 and R2 to sustain the reverse battery. Recommended connection with reverse battery protection1: +Bat C3 C4 Micro-processor C1 100nF I/O I/O IN Diag Vcc RIN CBoot IN Rpdiag AUIR33402S A/D Gnd Ifbk RpIfbk Ifbk Current shutdown programming resistor RIfbk Cboot 100nF Vbat + Mot Output Gnd C2 1nF D1 MBR 3045CT T1 IRF140 4 Gnd R2 10k - Mot GND D2 12V Figure 1: Recommended schematic This is the recommended schematic with an optional reverse battery1. The recommended load is an inductive load. This part may not be suitable for application conditions other than those specified above. Please contact IR’s Automotive Technical support for further details on other applications requirement. DC to 20 kHz operation The AUIR33402S is able to operate in DC and high speed switching operation. To be able to switch at 20 kHz, a bootstrap capacitor is used externally. The device integrates the power supply of the bootstrap capacitor. In DC operation, when the capacitor is discharged, the charge pump maintains the device ON. 1 The reverse battery is optional. Remove T1, D2, R2 and connect –Mot to Gnd to remove the features. 3 www.irf.com © 2014 International Rectifier Submit Datasheet Feedback August 14, 2014 Automotive Grade AUIR33402S Active dv/dt control to reduce EMI Typical Connection The AUIR33402S includes a special gate drive, managing the Mosfet dv/dt controlled internally, by managing the gate voltage dynamically. To have the best compromise between the EMI levels and power loss, during the turn on and off phase, the dv/dt output is dv/dt is not linear. The output voltage shape is an “S” shape. Sense Load current feedback and programmable current shutdown The Ifbk pin allows an analog measurement of the load current and with an external resistor allows to program the over current shutdown level from 10A to 33A. The voltage threshold level of the Ifbk pin is internally set to 4V (See the formulas below). It is also possible to dynamically adjust the current shutdown protection versus time by adding some external components. This protection is latched. The operating mode is recovered after resetting by the sleep mode. Rifbk Vifbk gnd min Ratio min Imax appli Offset Vifbk gnd max Ishtd max Ratio max Offset Rifbk calculated Where: Imax appli is the maximum application current Ishtd max is the maximum output shutdown current Internal over current shutdown The maximum current shutdown threshold value is internally fixed to 50A typ. This protection is latched. The operating mode is recovered after resetting by the sleep mode. Under voltage lock-out The AUIR33402S remains operational from UV Lo threshold. Under this continuous voltage, the device will be locked until the voltage recovers the operating range, according to an internal hysteresis fixed to 0,5V min. The maximum rating voltage is given by the Trench VDMOS technology where the avalanche voltage is up to 43V typically. Sleep mode and reset fault: The sleep mode is enabled if the IN pin stay low (Vin < Vin µpower) more than Tslp time. The consumption in sleep mode is Icc off. The AUIR33402S wakes up at first rise edge on the IN pin (Vin > Vin µpower). This mode allows resetting all the latched faults. (Cf. Figure 2: Wake sequence, sleep mode and reset latched fault.) Wake up sequence: The AUIR33402S has a power on reset. After wake up it by the IN signal, the devices wait for Tpwr_on_rst before activate the output power mosfet. This time is necessary to charge properly the bootstrap capacitor and to stabilize the internal power supply. (Cf. Figure 2: Wake sequence, sleep mode and reset latched fault.) 4 www.irf.com © 2014 International Rectifier Submit Datasheet Feedback August 14, 2014 AUIR33402S Automotive Grade In pin and digital diagnostic The IN has two functions. In normal working condition, the output follows the IN pin digital level. In latched fault condition (over current and over temperature shutdown), the IN pin provides a digital frequency signal feedback to the µ-processor. Reset fault Fault Vpwm Tpwron_rst Tslp Input pin Diag 5v 1 1 2 FDiag VdiagL 5v Vout Vcc Figure 2: Wake sequence, sleep mode and reset latched fault. 5 www.irf.com © 2014 International Rectifier Submit Datasheet Feedback August 14, 2014 AUIR33402S Automotive Grade Absolute Maximum Ratings Absolute maximum ratings indicate sustained limits beyond which damage to the device may occur. All voltage parameters are referenced to Vcc lead. (Tambient=25°C unless otherwise specified). Symbol Parameter Vout Vin Vcc max. Vcc cont Iin, max. Pd Maximum output voltage Maximum input voltage Maximum Vcc voltage Maximum continuous Vcc voltage Maximum input current Maximum power dissipation Rth=60°C/W Electrostatic discharge voltage (Human body) C=100pF, R=1500 Charge device model (CDM) Max. storage & operating temperature junction temperature Soldering temperature (10 seconds) ESD1 ESD2 Tj max. Tsoldering Min. Gnd-5v -0.3 Max. Vcc+0.3 5.5 36 28 10 2 4 1 150 300 -0.3 -40 Units V V V V mA W kV °C °C Thermal Characteristics Symbol Parameter Rth1 Rth2 Thermal resistance junction to ambient Thermal resistance junction to case Typ. 60 0.65 Max. Units °C/W Recommended Operating Conditions These values are given for a quick design. For operation outside these conditions, please consult the application notes. Symbol Parameter Vcc max. Iout Cboot RIN Rpdiag Power supply voltage DC output current Tj=145°C, Tamb=85°C, Rth=5°C/W Bootstrap capacitor Recommended resistor in series with In pin Recommended resistor in series with In pin to read the diagnostic Recommended resistor to program over current shutdown Recommended resistor in series with RIfbk pin to read the current feedback Maximum input frequency RIfbk RpIfbk F max. 6 www.irf.com © 2014 International Rectifier Min. Max. 6 100 1 10 18 33 220 10 50 V A nF k k 0.6 5 k 10 25 k 20 kHz Submit Datasheet Feedback Units August 14, 2014 AUIR33402S Automotive Grade Static Electrical Characteristics Tj=25°C, Vcc=14V (unless otherwise specified) Symbol Parameter VIL VIH Vin Hyst Iin, on ON state resistance Tj=25°C ON state resistance Tj=25°C ON state resistance Tj=150°C 2 Forward voltage of the body diode Supply current in µPower mode Gnd current when the device is on Output leakage when the MOSFET is off and the device is woken up Breakdown voltage between Vcc and Vout Input threshold voltage to enter in µpower mode IN Low threshold voltage IN High threshold voltage Input hysteresis On state input current Iboot Bootstrap current charge Vboot VdiagL Bootstrap voltage Low level diagnostic output voltage Rds(on) Vf Icc off Icc on Mos Lkg on Vbrk Vin µpower Min. Typ. Max. Units 3 3 5.5 3.5 3.5 m 0.55 1 3 1.1 10 5 V µA mA 8.5 15 mA 39 43 V 0.6 0.8 V 2 2.5 2.8 0.25 10 20 3 0.8 30 V V V µA 0.5 1.3 A 5.4 0.4 V V Test Conditions Iout=30A Iout=17A Vcc=6V Iout=30A Vin=0V I_Cboot = 0A Out = 0V Vin = 5v Vout = 0V Cboot =500nF Vin = 5V Rin = 1k Switching Electrical Characteristics Vcc=14V, Inductive load= 1 resistor, Tj=25°C (unless otherwise specified) 2 Symbol Parameter Td on Tr dv/dt(on) Td off Tf dv/dt(off) Turn-on delay time Rise time Turn on dv/dt Turn-off delay time Fall time Turn off dv/dt Min. Typ. Max. Units 0.5 1.35 1 20 2.5 1 20 1.8 µs µs V/µs µs µs V/µs 8 1.5 8 30 3.8 30 Conditions Guaranteed by design 7 www.irf.com © 2014 International Rectifier Submit Datasheet Feedback August 14, 2014 AUIR33402S Automotive Grade Protection Characteristics Vcc=14V, Tj=25°C (unless otherwise specified). Symbol Vifbk - Gnd Isd Isd 1k Tsd UV Ho UV Lo UV Hyst Tslp Tpwr_on_rst Fdiag Parameter Over current threshold voltage Maximum over current shutdown Current shutdown Rifbk = 1k Over temperature threshold Under voltage turn on Under voltage turn off Under voltage hysteresis Sleep mode time and fault reset Power on reset time diagnostic frequency Min. Typ. Max. Units 3.8 40 18 155 4.15 80 33 175 5.7 4.8 1.5 50 15 4 50 25 165 5 4.2 0.8 30 8.5 250 V A A °C V V V ms µs Hz Min. Typ. Max. Units -3 5250 0.18 6400 3 7450 A 0.5 20 7 Conditions Current Sense Characteristics Tj=25°C (unless otherwise specified), Rifb=1k Symbol Offset Ratio Parameter Load current diagnostic offset (I load– Offset) / Ifb Conditions Leads Assignment PART NUMBER 1 : Ifbk 2 : IN 3 : Gnd 4 : Vcc (Tab) 5 : CBoot 6 : OUT 7 : OUT 8 www.irf.com © 2014 International Rectifier AUIR33402S D2Pak 7 leads Submit Datasheet Feedback August 14, 2014 AUIR33402S Automotive Grade Vpulse Iboot Cboot dV dt AUIR33402S Vboot Vboot 4V dV 1V dt Figure 3 : Iboot test circuit AUIR33402S 15V 14V Vin Vout 90% 60% Dv on Dv off 10% Tdon Dt on Tdoff Tr Dt off Tf Figure 4 : Switching time test circuit 9 www.irf.com © 2014 International Rectifier Submit Datasheet Feedback August 14, 2014 AUIR33402S Automotive Grade Functional Block Diagram Vcc All values are typical Vss Treset Boot strap regulator Internal power supply Charge Pump On/Off Uvlo 6v R S Logic input Q Level Shifter Diagnostic 75V IN Cboot Driver & Dv/dt control 43V Tj > 165°C + 6V - + Vdd Isd fixed + 4V - Gnd Ifbk OUT Internal diode schematic All values are typical 10 www.irf.com © 2014 International Rectifier Submit Datasheet Feedback August 14, 2014 AUIR33402S Automotive Grade 4 VIL VIH Hihyst Vin uP 5 4 Voltage level in V Input voltage in V 3 2 1 0 3 Vifb-gnd 2 1 0 -50 -25 0 25 50 75 100 125 150 -50 -25 0 25 Temperature in °C 50 75 100 125 150 Temperature in °C Figure 5: Input parameters vs. temperature Figure 6: Vifb-gnd vs. temperature 6 180% 160% 5 4 UV LO 3 UV HI UV Hyst 2 1 120% 100% 80% 60% 40% 20% 0% 0 -50 -25 0 25 50 75 100 125 150 Temperature in °C Figure 7: Under voltage parameters vs. temperature 11 Normalized Rdson in % Battery voltage in V 140% www.irf.com © 2014 International Rectifier -50 -25 0 25 50 75 100 125 150 Tj, junction temperature in °C Figure 8: Normalized Rdson Vs Tj Submit Datasheet Feedback August 14, 2014 AUIR33402S Automotive Grade 12 40 35 10 30 25 6 Tpwr_on_rst 4 Time in ms Time in µs 8 20 Tslp 15 10 2 5 0 0 -50 -25 0 25 50 75 100 125 150 -50 -25 0 Temperature in °C 75 100 125 150 Figure 10: Tslp vs. temperature 70 1,6 60 1,4 1,2 50 Isd 1k 40 Isdf 1 Time in µs Current in A 50 Temperature in °C Figure 9: Tpwr_on_rst vs. temperature 30 20 10 0 -50 -25 0,8 0,6 0,4 Tr 0,2 Tf 0 0 25 50 75 100 125 150 Temperature in °C Figure 11: Current shutdown vs. temperature 12 25 www.irf.com © 2014 International Rectifier -50 -25 0 25 50 75 100 125 150 Temperature in °C Figure 12: Rise and fall time vs. temperature Submit Datasheet Feedback August 14, 2014 AUIR33402S Automotive Grade 6 25 5 20 3 Dv/dt in V/µs Time in µs 4 Tdon Tdoff 2 15 10 DvDtOn DvDtOff 5 1 0 -50 -25 0 0 25 50 75 100 125 150 -50 -25 0 Temperature in °C 25 50 75 100 125 150 Temperature in °C Figure 13: Tdon & off vs. temperature Figure 14: Dv/dt on & off vs. temperature 6 1,0 0,9 5 0,8 0,7 4 3 Vcboot 2 Time in µs Time in µs 0,6 0,5 Iboot 0,4 0,3 0,2 1 0,1 0 0,0 -50 -25 0 25 50 75 100 125 150 Temperature in °C Figure 15: Bootstrap voltage vs. temperature 13 www.irf.com © 2014 International Rectifier -50 -25 0 25 50 75 100 125 150 Temperature in °C Figure 16: Current bootstrap vs. temperature Submit Datasheet Feedback August 14, 2014 Automotive Grade AUIR33402S Figure 17: Transient thermal impedance vs. time 14 www.irf.com © 2014 International Rectifier Submit Datasheet Feedback August 14, 2014 Automotive Grade AUIR33402S Case Outline 7L D2PAK 15 www.irf.com © 2014 International Rectifier Submit Datasheet Feedback August 14, 2014 Automotive Grade AUIR33402S IMPORTANT NOTICE Unless specifically designated for the automotive market, International Rectifier Corporation and its subsidiaries (IR) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or services without notice. Part numbers designated with the “AU” prefix follow automotive industry and / or customer specific requirements with regards to product discontinuance and process change notification. All products are sold subject to IR’s terms and conditions of sale supplied at the time of order acknowledgment. IR warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with IR’s standard warranty. Testing and other quality control techniques are used to the extent IR deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. IR assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using IR components. To minimize the risks with customer products and applications, customers should provide adequate design and operating safeguards. Reproduction of IR information in IR data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alterations is an unfair and deceptive business practice. IR is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of IR products or serviced with statements different from or beyond the parameters stated by IR for that product or service voids all express and any implied warranties for the associated IR product or service and is an unfair and deceptive business practice. IR is not responsible or liable for any such statements. IR products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or in other applications intended to support or sustain life, or in any other application in which the failure of the IR product could create a situation where personal injury or death may occur. Should Buyer purchase or use IR products for any such unintended or unauthorized application, Buyer shall indemnify and hold International Rectifier and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that IR was negligent regarding the design or manufacture of the product. Only products certified as military grade by the Defense Logistics Agency (DLA) of the US Department of Defense, are designed and manufactured to meet DLA military specifications required by certain military, aerospace or other applications. Buyers acknowledge and agree that any use of IR products not certified by DLA as military-grade, in applications requiring military grade products, is solely at the Buyer’s own risk and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. IR products are neither designed nor intended for use in automotive applications or environments unless the specific IR products are designated by IR as compliant with ISO/TS 16949 requirements and bear a part number including the designation “AU”. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, IR will not be responsible for any failure to meet such requirements. For technical support, please contact IR’s Technical Assistance Center http://www.irf.com/technical-info/ WORLD HEADQUARTERS: 101 N. Sepulveda Blvd., El Segundo, California 90245 Tel: (310) 252-7105 16 www.irf.com © 2014 International Rectifier Submit Datasheet Feedback August 14, 2014 Automotive Grade Revision History Rev. Date A July 22, 2014 B July 25, 2014 August 14, 2014 C 17 www.irf.com AUIR33402S Notes/Changes Converted directly from “AUIR33401S datasheet Rev C_0.doc”; Removed note II in Qualification Information page; added Ordering Information on front page Page 15: replaced the case outline drawing with correct version Update Ordering information © 2014 International Rectifier Submit Datasheet Feedback August 14, 2014