SAW DUPLEXER PART NO.: ACTFD002_836.5-881.5_2016 Product Type: Customer: SAW DUPLEXER Description: Customer Part NO.: 836.5/881.5MHz, Band 5, Balanced output PREPARED BY Issued Date: 01/07/2015 CHECKED BY APPROVED BY Application Low-loss SAW duplexer for mobile telephone Cellular/WCDMA band 5 systems Low amplitude ripple Low insertion attenuation Features Ceramic Package for Surface Mounted Technology (SMT) RoHS compatible Package size 2.0x1.6 Approx. weight 0.014g Electrostatic Sensitive Device(ESD) Package Dimensions Ceramic Package: Unit：mm Pin Configuration 6 Antenna 3 TX Input 1,8 RX Output 2, 4 ,5, 7, 9 To Be Grounded Marking Top View, Laser Marking Code 2015 2016 2017 2018 1 a n A N 2 b p B P “D002”: Part number “＊＊”: Lot number (The code shown below varies in a 4-year cycle) 3 c q C Q 4 d r D R 5 e s E S 6 f t F T -2- ” · ”: 7 g u G U 8 h v H V 9 i w J W Terminal 1 10 j x K X 11 k y L Y 12 m z M Z Maximum Ratings Rating Value Unit Operating Temperature Range TA -30 ~ +85 °C Storage Temperature Range Tstg -40 ~ +85 °C DC Voltage (between any Terminals) VDC 5 V P 30 max dBm VESD 250 V RF Power (in BW) ESD Voltage （HB） Electrical Characteristics TX-ANT: Temperature range for specification: T=-30°C to +85°C Antenna terminating impedance: ZANT=50Ω||7.5nH RX terminating impedance: ZRX=100Ω(balanced) TX terminating impedance: ZTX=50Ω Minimu Item m Center Frequency Maximum Insertion Loss in 824.0 MHz–849.0MHz Amplitude Variation in Input in m Unit - 836.5 - MHz IL - 1.8 2.3 dB 0.6 1.0 dB 824.0 α 0.30 … 779.0MHz 25 33 - dB 779.0 … 804.0 MHz 27 29 - dB 869.0 … 894.0 MHz 47 54 - dB 1573.0 … 1578.0MHz 36 43 - dB 1648.0 … 1698.0 MHz 35 39 -- dB 2472.0 … 2547.0 MHz 23 26 -- dB 3296.0 … 3396.0 MHz 10 18 -- dB - 1.9:1 2.1:1 - 1.6:1 2.0:1 VSWR(TX port) 824.0 MHz–849.0MHz Output VSWR(ANT port) in Maximu fC MHz–849.0MHz Absolute Attenuation Typical 824.0 MHz–849.0MHz RoHS Compliant Electrostatic Sensitive Device -3- Typical Frequency Response TX-ANT -4- Electrical Characteristics ANT- RX-: Electrical Characteristics TX-ANT: Temperature range for specification: T=-30°C to +85°C Antenna terminating impedance: ZANT=50Ω||7.5nH RX terminating impedance: ZRX=100Ω(balanced) TX terminating impedance: ZTX=50Ω Minimu Item m Center Frequency Maximum Insertion Loss in 869.0 MHz–894.0MHz Amplitude Variation in Input in m Unit - 881.5 - MHz IL - 2.0 2.8 dB 1.0 1.5 dB 869.0 α 0.30 … 779.0MHz 35 47 - dB 779.0 … 804.0 MHz 38 52 - dB 824.0 … 849.0 MHz 52 65 - dB 1738.0 … 1788.0MHz 40 57 - dB 2400.0 … 2500.0 MHz 40 56 -- dB 2607.0 … 2682.0 MHz 35 45 -- dB 3476.0 … 3576.0 MHz 30 42 -- dB - 1.6:1 2.0:1 - 1.7:1 2.0:1 VSWR(ANT port) 869.0 MHz–894.0MHz Output VSWR(RX port) in Maximu fC MHz–894.0MHz Absolute Attenuation Typical 869.0 MHz–894.0MHz RoHS Compliant Electrostatic Sensitive Device -5- Typical Frequency Response ANT- RX -6- Electrical Characteristics TX-RX: Item Minimum Isolation Typical 824.0 MHz–849.0MHz IL 869.0 MHz–894.0MHz RoHS Compliant Maximum 52 55 dB 50 53 dB Electrostatic Sensitive Device Typical Frequency Response TX-RX -7- Unit - Remarks SAW devices should not be used in any type of fluid such as water, oil, organic solvent, etc. Be certain not to apply voltage exceeding the rated voltage of components. Do not operate outside the recommended operating temperature range of components. Sudden change of temperature shall be avoided, deterioration of the characteristics can occur. Be careful of soldering temperature and duration of components when soldering. Do not place soldering iron on the body of components. Be careful not to subject the terminals or leads of components to excessive force. SAW devices are electrostatic sensitive. Please avoid static voltage during operation and storage. Ultrasonic cleaning shall be avoided. Ultrasonic vibration may cause destruction of components. Test Circuit -8- Recommended Soldering Profile C ACT 2015. All Rights Reserved. ○ E 1. 2. 3. A The specifications of this device are subject to change or obsolescence without notice. Typically, equipment utilizing this device requires emissions testing and government approval, which is the responsibility of the equipment manufacturer. Our liability is only assumed for the Surface Acoustic Wave (SAW) component(s) per se, not for applications, processes and circuits implemented within components or assemblies. . -9-