2.5x0.7mm RIGHT ANGLE SMD CHIP LED LAMP Part Number: APFA2507LSURKSYKZGKC ATTENTION Hyper Red Super Bright Yellow Green OBSERVE PRECAUTIONS FOR HANDLING ELECTROSTATIC DISCHARGE SENSITIVE DEVICES Features Descriptions z 2.5x1.0x0.7mm right angle SMD LED, 0.7mm thick- z The Hyper Red source color devices are made with AlGaInP on GaAs substrate Light Emitting Diode. ness. z The Super Bright Yellow device is made with AlGaInP z Low power consumption. (on GaAs substrate) light emitting diode chip. z Wide viewing angle. z Ideal for backlight and indicator. z The Green source color devices are made with InGaN on Sapphire Light Emitting Diode. z Package : 3000pcs / reel. z Moisture sensitivity level : level 3. z Tinned pads for improved solderability. z Low current IF=2mA operating. z Electrostatic discharge and power surge could damage the LEDs. z It is recommended to use a wrist band or antielectrostatic glove when handling the LEDs. z RoHS compliant. z All devices, equipments and machineries must be electrically grounded. Package Dimensions RED YELLOW Notes: 1. All dimensions are in millimeters (inches). 2. Tolerance is ±0.15(0.006") unless otherwise noted. 3. The specifications, characteristics and technical data described in the datasheet are subject to change without prior notice. 4. The device has a single mounting surface. The device must be mounted according to the specifications. SPEC NO: DSAO6074 REV NO: V.1A DATE: NOV/25/2015 PAGE: 1 OF 7 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203015273 Selection Guide Part No. Emitting Color (Material) Iv (mcd) [2] @ 2mA Lens Type Min. Typ. 20 30 *6 *10 6 15 *6 *15 20 60 *20 *60 Hyper Red (AlGaInP) APFA2507LSURKSYKZGKC Water Clear Super Bright Yellow (AlGaInP) Green (InGaN) Viewing Angle [1] 2θ1/2 130° 115° 125° Notes: 1. θ1/2 is the angle from optical centerline where the luminous intensity is 1/2 of the optical peak value. 2. Luminous intensity / luminous Flux: +/-15%. * Luminous intensity value is traceable to the CIE127-2007 compliant national standards. Electrical / Optical Characteristics at TA=25°C Symbol Parameter Emitting Color Typ. λpeak Peak Wavelength Hyper Red Super Bright Yellow Green λD [1] Dominant Wavelength Δλ1/2 Max. Units Test Conditions 645 590 515 nm IF=2mA Hyper Red Super Bright Yellow Green 630 590 525 nm IF=2mA Spectral Line Half-width Hyper Red Super Bright Yellow Green 28 20 35 nm IF=2mA C Capacitance Hyper Red Super Bright Yellow Green 35 20 45 pF VF=0V;f=1MHz VF [2] Forward Voltage Hyper Red Super Bright Yellow Green 1.75 1.85 2.65 2.5 2.5 4.1 V IF=2mA IR Reverse Current Hyper Red Super Bright Yellow Green 10 10 50 uA VR=5V Notes: 1. Wavelength: +/-1nm. 2. Forward Voltage: +/-0.1V. 3. Wavelength value is traceable to the CIE127-2007 compliant national standards. 4. Excess driving current and / or operating temperature higher than recommended conditions may result in severe light degradation or premature failure. Absolute Maximum Ratings at TA=25°C Parameter Hyper Red Super Bright Yellow Green Units Power dissipation 75 75 102.5 mW DC Forward Current 30 30 25 mA Peak Forward Current [1] 185 175 150 mA Electrostatic Discharge Threshold (HBM) 3000 3000 450 V Reverse Voltage 5 Operating Temperature -40°C To +85°C Storage Temperature -40°C To +85°C V Notes: 1. 1/10 Duty Cycle, 0.1ms Pulse Width. SPEC NO: DSAO6074 REV NO: V.1A DATE: NOV/25/2015 PAGE: 2 OF 7 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203015273 APFA2507LSURKSYKZGKC Hyper Red SPEC NO: DSAO6074 REV NO: V.1A DATE: NOV/25/2015 PAGE: 3 OF 7 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203015273 Super Bright Yellow SPEC NO: DSAO6074 REV NO: V.1A DATE: NOV/25/2015 PAGE: 4 OF 7 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203015273 Green SPEC NO: DSAO6074 REV NO: V.1A DATE: NOV/25/2015 PAGE: 5 OF 7 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203015273 APFA2507LSURKSYKZGKC Reflow soldering is recommended and the soldering profile is shown below. Other soldering methods are not recommended as they might cause damage to the product. Recommended Soldering Pattern (Units : mm; Tolerance: ± 0.1) Reel Dimension Tape Dimensions (Units : mm) SPEC NO: DSAO6074 REV NO: V.1A DATE: NOV/25/2015 PAGE: 6 OF 7 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203015273 PACKING & LABEL SPECIFICATIONS APFA2507LSURKSYKZGKC Terms and conditions for the usage of this document 1. The information included in this document reflects representative usage scenarios and is intended for technical reference only. 2. The part number, type, and specifications mentioned in this document are subject to future change and improvement without notice. Before production usage customer should refer to the latest datasheet for the updated specifications. 3. When using the products referenced in this document, please make sure the product is being operated within the environmental and electrical limits specified in the datasheet. If customer usage exceeds the specified limits, Kingbright will not be responsible for any subsequent issues. 4. The information in this document applies to typical usage in consumer electronics applications. If customer's application has special reliability requirements or have life-threatening liabilities, such as automotive or medical usage, please consult with Kingbright representative for further assistance. 5. The contents and information of this document may not be reproduced or re-transmitted without permission by Kingbright. 6. All design applications should refer to Kingbright application notes available at http://www.KingbrightUSA.com/ApplicationNotes SPEC NO: DSAO6074 REV NO: V.1A DATE: NOV/25/2015 PAGE: 7 OF 7 APPROVED: Wynec CHECKED: Allen Liu DRAWN: L.Q.Xie ERP: 1203015273