ETC GDM12864A Liquid crystal display module Datasheet

User’s Guide
GDM12864A LCM
™
(Liquid Crystal Display Module)
XIAMEN OCULAR LCD DEVICES CO., LTD.
??????????????
South 5F., Guang Xia Bldg. Torch Hi-tech
Develop. Area, Xiamen, China 361006
Tel: (0592)6026045 Fax: (0592)6026021
GDM12864A LCM
Use’s Guide
Contents
Chapter 1. Introduction to ITM-12864A LCM
1
Features
Mechanical Specifications
Temperature Characteristics
External Dimensions
Application Diagram
Electro- Optical characteristics
Interface Pin Connections
Electrical Absolute Maximum Rating (KS0107B)
DC Electrical Characteristics (KS0107B)
Electrical Absolute Maximum Rating (KS0108B)
DC Electrical Characteristics (KS0108B)
1
1
1
2
3
4
5
6
6
7
7
Chapter 2. Driver IC (KS0107B) Function Description
Introduction
AC Characteristics
Master Mode
Slave Mode
Functional Description
RC Oscillator
Timing Generation Circuit
Data Shift & Phase Select Control
8
9
9
10
11
11
11
12
Chapter 3. Driver IC (KS0108B) Function Description
Introduction
AC Characteristics
Operating Principles & Methods
Display Control Instruction
8
13
13
16
19
13
Chapter 1 Introduction to GDM12864A LCM
CHAPTER 1
Introduction to ITM-12864A LCM
ITM-12864A is a dot matrix graphic LCD module which is fabricated by low power COMS
technology. It can display 128*64 dots size LCD panel using a 128*64 bit-mapped Display Data
RAM (DDRAM). It interfaces with an 8-bit microprocessor.
Features
??
??
??
??
??
??
??
??
??
Display format: 128*64 dots matrix graphic
STN yellow-green mode
Easy interface with 8-bit MPU
Low power consumption
LED back-light
Viewing angle: 6 O’clock
Driving method : 1/64 duty , 1/6.7 bias
LCD driver IC: KS0108B(2 ? )? KS0107B
Connector: Zebra
Mechanical Specifications
Item
Module Size(W*H*T)
Viewing Area(W*H)
Number of Dots
Dot Size(W*H)
Dot Pitch(W*H)
Module Size With B/L
Dimension
93.0*70.0*10.0
72.0*40.0
128.0*64.0
0.48*0.48
0.52*0.52
93.0*70.0*15.0
Unit
mm
mm
PCS
mm
mm
mm
Temperature Characteristics
Parameter
Operating temperature
Storage temperature
Symbol
Topr
Tstg
Rating
0 ~ +50
-20 ~ +70
Unit
?
?
1
Chapter 1 Introduction to GDM12864A LCM
Figure 1. External Dimensions
PIN
SIGNAL
PIN
SIGNAL
1
2
3
4
5
6
7
8
Vss
VDD
V0
D/I
R/W
E
DB0
DB1
DB2 DB3
11
12
13
14
15
16
17
18
19
20
DB4
DB5
DB6
DB7
CS1
CS2
RES
VEE
A
K
*NOTE: 1.All units are mm.
2.Tolerances unless otherwise specified ? 0.2.
INTECH
LCD
MODULE
ITM-12864A
9
10
2
3
Chapter 1 Introduction to GDM12864A LCM
Figure 2. Application Diagram
LCD panel
(128X64)
SEG1
.... SEG64
..
COM1
COM64
SEG65
.... SEG128
M
FRM
CLK1
CLK2
CL2
VDD
SHL
FS
MS
PCLK2
DS2
DS1
VSS
S64
M
FRM
CLK1
CLK2
CL2
KS0108B
(Bottom view)
VDD
V0
MPU
V1
E
RW
RS
DB[0:7]
RESETB
VSS
V2
V3
V4
CS2
CS1
V5
VSS
12
(Bottom view)
*Note
1/64 duty, 1/6.7 bias
VDD>V1>V2>V3>V4>V5>VEE
ADC
VDD
V0
V1
V2
V3
V4
V5
KS0108B
VEE
VSS
CS2B
S64
CS1B
E
RW
RS
DB[0:7]
RESETB
CS3
S1
VEE
M
FRM
CLK1
CLK2
CL2
C
VEE
V5
V4
V3
V2
V1
V0
ADC
VDD
V0
V1
V2
V3
V4
V5
VEE
VSS
CS2B
CS1B
E
RW
RS
DB[0:7]
RESETB
CS3
VSS
12
CR
KS0107B
S1
C64 C1 R
Chapter 1 Introduction to GDM12864A LCM
4
Electro-Optical characteristics
TN Type (Twisted Nematic )
Item
Symbol
?2 -?1
Viewing Angle
f
Min.
Typ.
Max.
Unit
Condition
Note
40
-
-
deg.
Cr = 2.0
1,2
?=20?
f = 0?
?=20?
f = 0?
?=20?
f = 0?
Contrast Ratio
Cr
-
4
-
-
Response Time (rise)
tR
-
110
-
ms
Response Time (fall)
tF
-
110
-
ms
Typ.
Max.
Unit
Condition
Note
-
+90
deg.
Cr = 2.0
1,2
STN Type (Super Twisted Nematic )
Item
Symbol
Min.
70
?2 -?1
Viewing Angle
-90
f
Contrast Ratio
Cr
-
4
-
-
Response Time (rise)
tR
-
110
-
ms
Response Time (fall)
tF
-
110
-
ms
1. Definition of angle ¦È & ¦Õ
3
4
4
?=20?
f = 0?
?=20?
f = 0?
?=20?
f = 0?
3
4
4
2. Definition of viewing angle ¦È 1 & ¦Õ 2
Cr
Y(¦Õ=180 ¦Ï )
¦È 2
¦Ï
¦È 1<20 <¦È 2
¦È 1
2.0
¦È 1
¦Ï
Y’(¦Õ=0 )
3. Definition of contrast Cr
100%
Intensity
¦È 2
4. Definition of optical response
B
On
Off
Selected
Dots
A
Set Point
Cr = ( A / B ) p
Off
90%
Nonselected
Dots
0%
20 ¦Ï
Intensity 100%
10%
100%
Driving Voltage
Negative : P = -1
Positive : P = +1
tR
Time
tF
Chapter 1 Introduction to GDM12864A LCM
Interface Pin Connections
Pin
No.
1
2
3
4
Symbol
I/O Type Description
VSS
VDD
V0
D/I
Supply
Supply
Supply
Ground
Power supply
LCD driver supply voltage
Data input/output pin of internal shift register
MS
5
SHL
H
H
H
L
L
H
L
L
Read or Write
R/W
DIO1
Output
Output
Input
Output
DIO2
Output
Output
Output
Input
RW
Description
H
Data appears at DB[7:0] and can be read by the CPU while
E= H CS1B=L,CS2B=L and CS3=H.
L
Display data DB[7:0] can be written at falling edge of E
when CS1B=L, CS2B=L and CS3=H.
6
E
Enable signal
E
H
L
7
8
9
10
11
12
13
14
15
16
DB0
DB1
DB2
DB3
DB4
DB5
DB6
DB7
CS1
CS2
17
RESETB
I/O
Description
Read data in DB[7:0] appears while E= “High”.
Display data DB[7:0] is latched at falling edge of E.
Data bus [0~7]
Bi-directional data bus
I
Chip selection
When CS1=H,CS2=L, select IC1
I
When CS1=L,CS2=H, select IC2
Reset signal.
When RSTB=L
? 1? ON/OFF
register becomes set by 0.(display off)
? 2? display start line register becomes set by 0 (Z-address 0 set, display
from line 0)
? 3? After releasing reset , this condition can be changed only by
instruction.
18
19
20
VEE
A
K
Power
VEE is connected by the same voltage.
Back-light anode
Back-light cathode
5
6
Chapter 1 Introduction to GDM12864A LCM
Electrical Absolute Maximum Ratings (KS0107B)
Parameter
Operating voltage
Supply voltage
Driver supply voltage
Symbol
VDD
VEE
VB
VLCD
Rating
-0.3 ~ +7.0
VDD-19.0 ~ VDD+0.3
-0.3 ~ VDD+0.3
VEE-0.3 ~ VDD+0.3
Unit
V
V
V
V
Note
*1
*4
*1,2
*3,4
*Notes:
*1. Based on VSS = 0V
*2. Applies to input terminals and I/O terminals at high impedance. (Except V0L, V1L, V4L, and
V5L)
*3. Applies to V0L, V1L, V4L, and V5L.
*4. Voltage level: VDD=V0=V1=V2=V3=V4=V5=VEE
DC Electrical Characteristics(KS0107B)
(VDD= 4.5 to 5.5V, VSS=0V,VDD-VEE=8~17V,Ta= -30 to +85? )
Item
Symbo Condition
Min.
l
Operating voltage
VDD
4.5
Input voltage
VIH
0.7VDD
VIL
VSS
Typ.
Max.
Unit
-
5.5
VDD
0.3VD
V
Note
*1
D
output voltage
VOH
VOL
Input leakage current ILKG
OSC Frequency
fosc
On Resistance
(Vdiv-Ci)
Operating current
RONS
IDD1
IDD2
Supply Current
IEE
Operating
fop1
Frequency
fop2
IOH= -0.4mA
IOL= 0.4mA
VIN= VDD ~ VSS
Rf=47kO±2%
Cf=20pF±5%
VDD-VEE=17V
Load current±150?A
Master mode
1/128 Duty
Master mode
1/128 Duty
Master mode
1/128 Duty
Master mode
External Duty
Slave mode
VDD-0.4
-1.0
315
450
0.4
+1.0
585
*2
?A
kHz
-
-
1.5
kO
-
-
1.0
mA
-
-
0.2
*4
-
-
0.1
*5
50
-
600
0.5
-
1500
*1
*3
kHz
Notes
*1. Applies to input terminals FS, DS1, DS2, CR, SHL, MS and PCLK2 and I/O terminals DIO1,
DIO2, M , and CL2 in the input state.
*2. Applies to output terminals CLK1, CLK2 and FRM and I/O terminals DIO1, DIO2, M , and
CL2 in the output state.
*3. This value is specified about current flowing through VSS.
Internal oscillation circuit: Rf=47kO, cf=20pF
Each terminals of DS1, DS2, FS, SHL, and MS is connected to VDD and out is no load.
*4. This value is specified about current flowing through VSS.
Each terminals is DS1, DS2, FS, SHL, PCLK2 and CR is connected to VDD,MS is connected to VSS
and CL2, M, DIO1 is external clock.
*5. This value is specified about current flowing through VEE, Don’t connect to VLCD (V1~V5).
7
Chapter 1 Introduction to GDM12864A LCM
Electrical Absolute Maximum Ratings(KS0108B)
Parameter
Operating voltage
Supply voltage
Driver supply voltage
Symbol
VDD
VEE
VB
VLCD
Rating
-0.3 ~ +7.0
VDD-19.0 ~ VDD+0.3
-0.3 ~ VDD+0.3
VEE-0.3 ~ VDD+0.3
Unit
V
V
V
V
Note
*1
*4
*1,3
*2
*Notes:
*1. Based on VSS = 0V
*2. Applies the same supply voltage to VEE. VLCD=VDD-VEE.
*3. Applies to M, FRM, CLK1,CLK2, CL, RESETB, ADC, CS1B, CS2B,CS3, E, R/W, RS and
DB0~DB7.
*4. Applies V0L,V2L,V3L and V5L.
Voltage level: VDD=V0=V1=V2=V3=V4=V5=VEE
DC Electrical Characteristics(KS0108B)
(VDD= 4.5 to 5.5V, VSS=0V,VDD-VEE=8~17V,Ta= -30 to +85? )
Item
Symbol Condition
Min.
Operating voltage
VDD
4.5
Input High voltage
VIH1
0.7VDD
VIH2
2.0
Input Low voltage
VIL1
0
Typ.
-
Max.
5.5
VDD
VDD
0.3VD
Unit
V
Note
*1
*2
*1
D
Output High Voltage
Output Low Voltage
Input leakage current
Three-state (OFF)
Input Current
Driver Input leakage
current
On Resistance
(Vdiv-Ci)
Operating current
VIL2
VOH
VOL
ILKG
ITSL
IOH= -0.2mA
IOL= 1.6mA
VIN= VSS ~ VDD
VIN= VSS ~ VDD
0
2.4
-1.0
-5.0
IDIL
VIN= VEE ~ VDD
-2.0
RONS
VDD-VEE=15V
Load current±100?A
During Display
During Access
Access Cycle=1MHz
-
-
7.5
kO
*8
-
-
0.1
0.5
mA
*7
*7
IDD1
IDD2
-
0.8
0.4
+1.0
5.0
?A
2.0
Notes
*1. CL, FRM, M, RSTB, CLK1, CLK2
*2. CS1B, CS2B, CS3, E, R/W, RS, DB0~DB7
*3. DB0~DB7
*4. Except DB0~DB7
*5. DB0~DB7 at high impedance
*6. V0, V1, V3, V3, V4, V5
*7. 1/64 duty , FCLK=250KHZ, Frame Frequency=70HKZ, Output: No Load
*8. VDD-VEE=15.5V
V0L>V2L>= VDD-2/7(VDD-VEE)>V3L= VEE+2/7(VDD-VEE)>V5L
*2
*3
*3
*4
*5
*6
64CH Common Driver For Dot Matrix LCD
CHAPTER 2
Driver IC Function Description
KS0107 Driver IC
64COM graphic driver for dot matrix LCD
Introduction
The KS0107B is an :CD driver LSI with 64 channel outputs for dot matrix liquid crystal graphic
display systems.
This device provides 64 shift registers and 64 output drivers.
It generates the timing signal to control the KS0108B (64 channel segment drover.).
The KS0107B is fabricated by low power CMOS high voltage process technology, and is composed
of the liquid crystal display system in combination with the KS0108B (64 channel segment drover.).
© 1998 Intech LCD Group Ltd.
8
64CH Common Driver For Dot Matrix LCD
AC Characteristics (VDD=4.5~5.5V, Ta=-30? ~+85? )
1. Master mode (MS=V DD, PCLK2=V DD, Cf=20pF, Rf=47KO)
CL2
t WLC
0.7VDD
0.3VDD
tWHC
t WHC
tDH
tSU
tSU
DIO1(SHL=V DD)
DIO2(SHL=V SS)
tD
tD
DIO2(SHL=VDD )
DIO1(SHL=VSS)
tDF
FRM
tDM
t DM
0.7VDD
M
0.3VDD
tR
tWH1
tWL1
CLK1
t D21
t D12
tF
CLK2
tWH2
tF
Characteristic
Data Setup Time
Data Hold Time
Data Delay Time
FRM Delay Time
M Delay Time
CL2 Low Level Width
CL2 High Level Width
CLK1 Low Level Width
CLK2 Low Level Width
CLK1 High Level Width
CLK2 High Level Width
CLK1-CLK2 Phase Difference
CLK2-CLK1 Phase Difference
CLK1,CLK2 Rise/Fall Time
© 1998 Intech LCD Group Ltd.
tR
Symbol
tSU
tDH
tD
tDF
tDM
tWLC
tWHC
tWL1
tWL2
tWH1
tWH2
tD12
tD21
tR/t F
Min
20
40
5
-2
-2
35
35
700
700
2100
2100
700
700
-
Typ
-
Max
2
2
150
Unit
?s
ns
9
64CH Common Driver For Dot Matrix LCD
Slave mode (MS=VSS)
CL2
(PLK2=VSS)
tF
tWLC1
tR
0.7VDD
tWHC1
tSU
CL2
(PLK2=VDD)
tWLC2
tWLC
tF
tR
tD
tHCL
0.7VDD
0.3VDD
DIO1(SHL=VDD)
DIO2(SHL=VSS)
Input Data
tH
DIO1(SHL=VDD)
0.7VDD
0.3VDD
DIO2(SHL=VSS)
Output Data
Characteristics
CL2 Low Level Width
CL2 High Level Width
CL2 Low Level Width
CL2 High Level Width
Data Setup Time
Data Hold Time
Data Delay Time
Output Data Hold Time
CL2 Rise/Fall Time
0.3VDD
Symbol
tWLC1
tWHC1
tWLC2
tWHL
tSU
tDH
tD
tH
tR/tF
Min
450
150
150
450
100
100
10
-
Typ
-
*1: Connect load CL=30pF
OUTPUT
30pF
© 1998 Intech LCD Group Ltd.
Max
200
30
Unit
ns
Note
PCLK2=VSS
PCLK2=VSS
PCLK2=VDD
PCLK2=VDD
*1
10
64CH Common Driver For Dot Matrix LCD
11
FUNCTIONAL DESCRIPTION
1.RC Oscillator
The RC Oscillator generates CL2, M, FRM, of the KS0107B and CLK1, CLK2 of the KS0107B by the
oscillation resister R and capacitor C.
When selecting the master/slave, oscillation circuit is as following:
1)
Master Mode
KS0107B
KS0107B
R
CR
Rf
2)
C
R
open
Cf
CR
C
open
External clock
Slave Mode
KS0107B
R
open
CR
VDD
C
open
2.Timing Generation circuit
It generates CL2, M, FRM, CLK1, and CLK2 by the frequency from oscillation circuit.
1)
2)
Selection of Master/Slave (M/S)
When M/S is “H”, it generates CL2, M, FRM, CLK1, and CLK2 internally. When M/S is “L”,
it operates by receiving M, CLK2 from master device.
Frequency Selection (FS)
To adjust FRM by 70Hz, the oscillation frequency should be as following:
FS
Oscillation Frequency
H
L
fOSC =430KHz
fOSC =215KHz
In the slave mode, it is connected to VDD.
© 1998 Intech LCD Group Ltd.
64CH Common Driver For Dot Matrix LCD
3)
Duty Selection (DS1, DS2)
It provides various duty selection according to DS1, DS2.
DS1
L
DS2
L
H
L
H
H
3.
12
DUTY
1/48
1/64
1/96
1/128
Data shift & Phase Select Control
1)
2)
Phase Selection
It is a circuit to shift data on synchronization or rising edge or falling edge of the CL2 according
to PCLK2.
PCLK2
Phase Selection
H
L
Data shift on rising edge of CL2
Data shift on falling edge of CL2
Data shift Direction Selection
When M/S is connected to VDD, DIO1 and DIO2 terminal is only output.
When M/S is connected to VSS, it depends on the SHL.
MS
H
L
SHL
H
L
H
L
DIO1
Output
Output
Input
Output
© 1998 Intech LCD Group Ltd.
DIO2
Output
Output
Output
Input
Direction of Data
C1~C64
C64~C1
DIO1~C1~C64~DIO2
DIO2~C64~C1~DIO1
64CH Segment Driver For Dot Matrix LCD
13
CHAPTER 3
Driver IC Function Description
KS0108 Driver IC
64 SEG graphic driver for dot matrix LCD
Introduction
The KS0108B is an LCD driver LSI with 64 channel outputs for dot matrix liquid crystal graphic
display systems. This device consists of the display RAM, 64 bit data latch 64 bit drivers and decoder
logics. It has the internal display RAM for storing the display data transferred from a 8 bit micro
controller and generates the dot matrix liquid crystal driving signals corresponding to stored data. The
KS0108B composed of the liquid crystal display system in combination with the KS0107B(64
common driver).
AC Characteristics (VDD=4.5~5.5V ,VSS=0V, Ta=-30? ~+85? )
( 1)
Clock Timing
Characteristic
CLK1, CLK2 Cycle Time
CLK1‘LOW’Level Width
CLK2‘LOW’Level Width
CLK1‘HIGH’Level Width
CLK2‘HIGH’Level Width
CLK1-CLK2 Phase Difference
CLK2-CLK1 Phase Difference
CLK1, CLK2 Rise Time
CLK1, CLK2 Fall Time
© 1998 Intech LCD Group Ltd.
Symbol
tCY
tWL1
tWL2
tWH1
tWH2
tD12
tD21
tR
tF
Min
2.5
625
625
1875
1875
625
625
-
Typ
-
Max
20
150
150
Unit
?s
ns
64CH Segment Driver For Dot Matrix LCD
tC Y
C LK1
tF
0 .7 V D D
0 .3 V D D
tW H 1
tR
tW L 1
C LK2
tD 1 2
tW L 2
0 .7 V D D
0 .3 V D D
tF
t D 21
tF
t W H2
tC Y
( 2) .Display Control Timing
Characteristic
FRM Delay Time
M Delay Time
CL ‘LOW’Level Width
CL‘HIGH’Level Width
Symbol
tDF
tDM
tWL
tWH
Min
-2
-2
35
35
Typ
-
Max
2
2
-
tWL
CL
0.7VDD
0.3VDD
tWH
tDF
FRM
tDF
0.7VDD
0.3VDD
tDM
M
© 1998 Intech LCD Group Ltd.
0. 7VDD
0.3VDD
Unit
us
14
64CH Segment Driver For Dot Matrix LCD
( 3) . MPU Interface
Characteristic
E Cycle
E High Level Width
E Low Level Width
E Rise Time
E Fall Time
Address Set-Up Time
Address Hold Time
Data Set-Up Time
Data Delay Time
Data Hold Time (Write)
Data Hold Time (Read)
Symbol
tC
tWH
tWL
tR
tF
tASU
tAH
tSU
tD
tDHW
tDHR
Min
1000
450
450
140
10
200
10
20
Typ
-
Max
25
25
320
-
Unit
ns
tC
E
tWL
tWH
tR
R/W
tF
tAH
tASU
tASU
tAH
CS1B,CS2B
CS3,RS
tDSU
DB0~DB7
MPU Write timing
© 1998 Intech LCD Group Ltd.
tDHW
15
64CH Segment Driver For Dot Matrix LCD
16
tC
E
tWL
tWH
tR
tF
R/W
tASU
tAH
tASU
tAH
CS1B,CS2B
CS3,RS
tD
tWH
DB0~DB7
MPU Read timing
OPERATING PRINCIPLES & METHODS
1.
I/O Buffer
Input buffer controls the status between the enable and disable of chip. Unless the CS1B to CS3 is in
active mode, Input or output of data and instruction does not execute. Therefore internal state is not
change. But RSTB and ADC can operate regardless CS!B-CS3.
2.
Input register
Input register is provided to interface with MPU which is different operating frequency. Input register
stores the data temporarily before writing it into display RAM.
When CS1B to CS3 are in the active mode, R/W and RS select the input register. The data from MPU
is written into input register. Then writing it into display RAM. Data latched for falling of the E signal
and write automatically into the display data RAM by internal operation.
3.
Output register
Output register stores the data temporarily from display data RAM when CS1B, CS2B and CS3 are in
active mode and R/W and RS=H, stored data in display data RAM is latched in output register. When
CS1B to CS3 is in active mode and R/W=H , RS=L, status data (busy check) can read out.
To read the contents of display data RAM, twice access of read instruction is needed. In first access,
data in display data RAM is latched into output register. In second access, MPU can read data which is
latched. That is to read the data in display data RAM, it needs dummy read. But status read is not
needed dummy read.
© 1998 Intech LCD Group Ltd.
64CH Segment Driver For Dot Matrix LCD
RS
L
R/W
L
H
L
H
H
4.
17
Function
Instruction
Status read (busy check)
Data write (from input register to display data RAM )
Data read (from display data RAM to output register)
Reset
The system can be initialized by setting RSTB terminal at low level when turning power on, receiving
instruction from MPU. When RSTB becomes low, following procedure is occurred.
1. Display off
2. Display start line register become set by 0.(Z-address 0)
While RSTB is low, No instruction except status read can by accepted. Therefore, execute other
instructions after making sure that DB4= (clear RSTB) and DB7=0 (ready) by status read instruction.
The conditions of power supply at initial power up are shown in table 1.
Table 1. Power Supply Initial Conditions
Item
Symbol
Min
Typ
Max
Unit
Reset Time
Rise Time
tRS
tR
1.0
-
-
200
us
ns
4.5[V]
V DD
t RS
RSTB
5.
tR
0.7V DD
0.3V DD
Busy flag
Busy flag indicates that KS0108B is operating or no operating. When busy flag is high, KS0108B is in
internal operating .
When busy flag is low, KS0108B can accept the data or instruction.
DB7indicates busy flag of the KS0108B.
E
Busy Flag
T Busy
1/fCLK<T Busy<3/fCLK
fCLK is CLK1, CLK2 Frequency
© 1998 Intech LCD Group Ltd.
64CH Segment Driver For Dot Matrix LCD
18
6.
Display On/Off Flip-Flop
The display on/off flip-flop makes on/off the liquid crystal display. When flip-flop is reset (logical low),
selective voltage or non selective voltage appears on segment output terminals. When flip-flop is set
(logic high), non selective voltage appears on segment output terminals regardless of display RAM data.
The display on/off flip-flop can changes status by instruction. The display data at all segment disappear
while RSTB is low.
The status of the flip-flop is output to DB5 by status read instruction.
The display on/off flip-flop synchronized by CL signal.
7.
X Page Register
X page register designates pages of the internal display data RAM.
Count function is not available. An address is set by instruction.
8.
Y address counter
Y address counter designates address of the internal display data RAM. An address is set by instruction
and is increased by 1 automatically by read or write operations of display data.
9.
Display Data RAM
Display data RAM stores a display data for liquid crystal display. To indicate on state dot matrix of
liquid crystal display , write datra1. The other way , off state, writes 0.
Display data RAM address and segment output can be controlled by ADC signal.
ADC=H => Y-address 0: S1~Y address 63: S64
ADC=L => Y-address 0: S64~Yaddress 63: S1
ADC terminal connect the VDD or VSS.
10. Display Start Line Register
The display start line register indicates of display data RAM to display top line of liquid crystal display.
Bit data (DB<0.5>) of the display start line set instruction is latched in display start line register.
Latched data is transferred to the Z address counter while FRM is high, presetting the Z address
counter.
It is used for scrolling of the liquid crystal display screen.
© 1998 Intech LCD Group Ltd.
64CH Segment Driver For Dot Matrix LCD
19
Display Control Instruction
The display control instructions control the internal state of the KS0108B. Instruction is received from MPU
to KS0108B for the display control. The following table shows various instructions.
Instruction
RS
RW
Read Display
Date
1
1
Read data
Write Display
Date
1
0
Write data
Status Read
0
1
Busy
0
Set Address
(Y address)
0
0
0
1
Y address (0~63)
Set Display
Start Line
0
0
1
1
Display start line (0~63)
Set Address (X
address)
0
0
1
0
1
1
1
Display On/off
0
0
0
0
1
1
1
1.
DB7
DB6
DB5
ON/
OFF
DB4
Reset
DB3
0
DB2
DB1
DB0
0
0
0
Page (0~7)
1
1
0/1
Function
Reads data (DB[7:0]) from
display data RAM to the
data bus.
Writes data (DB[7:0]) into
the DDRAM. After writing
instruction, Y address is
incriminated by 1
automatically
Reads the internal status
BUSY
0: Ready
1: In operation
ON/OFF
0: Display ON
1: Display OFF
RESET
0: Normal
1: Reset
Sets the Y address at the
column address counter
Indicates the Display Data
RAM displayed at the top of
the screen.
Sets the X address at the X
address register.
Controls the display ON or
OFF. The internal status and
the DDRAM data is not
affected.
0: OFF, 1: ON
Display On/Off
The display data appears when D is 1 and disappears when D is 0.
Though the data is not on the screen with D=0, it remains in the display data RAM.
Therefore, you can make it appear by changing D=0 into D=1.
RS R/W DB7
DB6
DB5
DB4
DB3
DB2
DB1
DB0
0
0
0
0
1
1
1
1
1
D
2.
Set Address (Y Address)
Y address (AC0~AC5) of the display data RAM is set in the Y address counter.
An address is set by instruction and increased by 1 automatically by read or write operations of
display data.
RS
0
R/W
0
DB7
0
DB6
1
© 1998 Intech LCD Group Ltd.
DB5
AC5
DB4
AC4
DB3
AC3
DB2
AC2
DB1
AC1
DB0
AC0
64CH Segment Driver For Dot Matrix LCD
3.
20
Set Page (X Address)
X address (AC0~AC2) of the display data RAM is set in the X address register.
Writing or reading to or from MPU is executed in this specified page until the next page is set.
RS
0
4.
R/W
0
DB7
1
DB6
0
DB5
1
DB4
1
DB3
1
DB2
AC2
DB1
AC1
DB0
AC0
Display Start Line (Z Address)
Z address (AC0~AC5) of the display data RAM is set in the display start line register and displayed at
the top of the screen.
When the display duty cycle is 1/64 or others (1/32~1/64), the data of total line number of LCD
screen, from the line specified by display start line instruction, is displayed.
RS
0
5.
R/W
0
DB7
1
DB6
1
DB5
AC5
DB4
AC4
DB3
AC3
DB2
AC2
DB1
AC1
DB0
AC0
DB7
BUS
Y
DB6
DB5
DB4
DB3
DB2
DB1
DB0
0
ON/OFF
RESET
0
0
0
0
Status Read
RS
R/W
1
0
?? BUSY
When BUSY is 1, the Chip is executing internal operation and no instructions are accepted.
When BUSY is 0, the Chip is ready to accept any instructions.
?? ON/OFF
When ON/OFF is 1, the display is on.
When ON/OFF is 0, the display is off.
?? RESET
When RESET is 1, the system is being initialized.
In this condition, no instructions except status read can be accepted.
When RESET is 0, initializing has finished and the system is in the usual operation condition.
6.
Write Display Data
Writes data (D0~D7) into the display data RAM.
After writing instruction, Y address is increased by 1 automatically.
RS R/W DB7
DB6
DB5
DB4
DB3
DB2
DB1
0
1
D7
D6
D5
D4
D3
D2
D1
7.
DB0
D0
Read Display Data
Reads data (D0~D7) from the display data RAM.
After reading instruction, Y address is increased by 1 automatically.
RS R/W DB7
DB6
DB5
DB4
DB3
DB2
DB1
1
1
D7
D6
D5
D4
D3
D2
D1
© 1998 Intech LCD Group Ltd.
DB0
D0