THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722 WWW.CONWIN.COM PRODUCT D ATA SHEET CRYSTAL CONTROLLED OSCILLATORS 14 PIN DIP 5.0V HCMOS STRATUM 3 OCVCXO with OVEN READY MONITOR ABSOLUTE MAXIMUM RATINGS PARAMETER Storage Temperature TABLE 1.0 UNITS MINIMUM -40 NOMINAL - MAXIMUM 85 UNITS °C Supply Voltage (Vcc) -0.5 - 7.0 Vdc Control Voltage (Vc) -0.5 - 7.0 Vdc OPERATING SPECIFICATIONS PARAMETER Center Frequency Frequency Stability Total Frequency Tolerance Operating Temperature Range Supply Voltage (Vcc) MINIMUM 40 -0.25 -4.6 0 NOMINAL - MAXIMUM 80 0.25 4.6 70 UNITS MHz ppm ppm °C Vdc 4.75 5.00 5.25 Power Consumption (Vcc = 5.0V) - - 2.0 W Phase Jitter (BW =12KHz to 20MHz) - - 1 pS RMS Phase Jitter (BW =10Hz to 20MHz) - - 3 pS RMS Period Jitter SSB Phase Noise at 10Hz offset SSB Phase Noise at 10KHz offset Start Up Time: Oscillator Warm Up Time TDEV @ 1.0 Sec. TDEV @ 4.0 Sec. - -75 -130 - 3 10 1 1 2 pS RMS dBc/Hz dBc/Hz mS Minute nS nS INPUT CHARACTERISTICS Control Voltage Range (Pin 1) MINIMUM NOMINAL MAXIMUM UNITS 0.5 2.5 4.5 Vdc +/-18 - +/-30 ppm 9 - - ppm/V (Vc) Frequency Pullability Slope of Frequency Adjust Input Impedance NOTE 1 2 100k - - Ohm (Pin 3) (Vih) 2.0 - - Vdc Disable Voltage (Pin 3) (Vil) - - 0.8 Vdc FEATURES MINIMUM 4.0 - NOMINAL - MAXIMUM 15 0.4 UNITS pf Vdc Vdc -4 45 50 4 55 mA mA % - - 6 nS Pin 12 - - 0.4 Vdc Pin 12 3.0 - - Vdc (Voh) (Vol) Current (High) (Low) Duty Cycle measured at 1.5V FREQUENCY ADJUST TRI-STATE ENABLE / DISABLE FUNCTION LOW JITTER <1pS RMS FREQUENCY TOLERANCE: ±4.6ppm NOTE TEMPERATURE RANGE: 0 to 70°C OVEN READY MONITOR HERMETICALLY SEALED PACKAGE RoHS COMPLIANT / LEAD FREE ORDERING INFORMATION TABLE 5.0 PACKAGE CHARACTERISTICS 5.0V OPERATION FREQUENCY STABILITY: ±0.25ppm TABLE 4.0 (Ioh) (Ioh) Rise / Fall Time 10% to 90% Oven Ready Monitor voltage when oven is cold, not at operating temperature. Oven Ready Monitor voltage when oven is warm, at operating temperature. NOTE 5 HCMOS OUTPUT CHARACTERISTICS PARAMETER LOAD Voltage (High) (Low) The Connor-Winfield EGOV5S3M is a hermetically sealed 14 Pin DIP 5.0V Oven Controlled, Voltage Controlled Crystal Oscillator (OCVCXO) with a Tri-State HCMOS output. The EGOV5S3M features an Oven Ready Monitor and is designed for Stratum 3 applications requiring low jitter and tight frequency stability. 3 4 Enable Voltage Package Soldering Process DESCRIPTION TABLE 3.0 PARAMETER EGOV5S3M NOTE TABLE 2.0 (Fo) CW 0803 EGOV5S3M 80.0MHZ 14 pin DIP, hermetically sealed, grounded case, welded package RoHS compliant, lead free. See solder profile on page 2. EGOV5S3M OCXO SERIES - 080.0M CENTER FREQUENCY Specifications subject to change without notice. DATA SHEET #: Cx061 PAGE 1 OF 2 REV: 01 DATE: 01/16/08 aCopyright 2008 Connor-Winfield all rights reserved. THE CONNOR-WINFIELD CORP. 2111 COMPREHENSIVE DRIVE. AURORA, IL 60505. FAX (630) 851-5040. PHONE (630) 851-4722 WWW.CONWIN.COM PRODUCT D ATA SHEET CRYSTAL CONTROLLED OSCILLATORS Notes: 1) Frequency vs. temperature stability, Vc = 2.50V. 2) Inclusive of calibration, operating temperature range, supply voltage change, load change, shock and vibration, 10 years aging, Vc = 2.50V. 3) After one minute of operation at 25C, the unit will be within +/-0.5ppm of its final stabilized frequency. The final stabilized frequency is that which is measured after 30 minutes of continuous operation at a stable 25C ambient temperature. 4) Referenced to Fo @ 25°C, Positive Transfer Characteristic 5) Oscillator output is enabled with no connection on pin 3. ENVIRONMENTAL CHARACTERISTICS Temperature Cycle: Per MIL-STD-883, Method 1010, Condition B. -55°C to 125°C, 20 cycles,10 minute dwell, 1minute transition. Gross Leak Test: Per MIL-STD-202, Method 112, Condition D. No bubbles in flourinert (FC-43) at 125°C ±5°C for 20 seconds. SOLDERING Pin Solderability: Per MIL-STD-883, Method 200. 8 hour steam age prior to 254°C ±5°C Solder pot dip, 95% Coverage. Resistance to Solder Heat: Per MIL-STD-202, Method 210, Condition C. Wave: Topside board-mount product, 260°C ±5°C for 20 Seconds. MECHANICAL CHARACTERISTICS Vibration: Per MIL-STD-202, Method 204, Condition A. 10G’s peak, 10Hz to 500Hz, 15minute cycles 12 times each perpendicular axis. Shock: Per MIL-STD-202, Method 213, Condition D. 500G’s, 1ms, halfsine, 3 shocks per direction. Moisture Resistance: Per MIL-STD-202, Method 106. 95% RH @ 65°C, 10 cycles 10°C to 65°C. Pin Connections Package Outline TABLE 6.0 .430 MAX Pin 1 3 7 8 12 14 (10.922mm) .200 (5.08mm) Dimensional Tolerance: ±.005 (.127mm) Test Circuit Connection Control Voltage Enable / Disable Ground (Case) Output Oven Monitor Vcc Solder Profile Temperature 260°C 260°C 220°C OVEN MONITOR REF. SUPPLY 4.5Vdc 14 5.0Vdc 12 180°C 150°C 8 120°C WW 1 20K POT 3 7 ENABLE/ CONTROL DISABLE VOLTAGE 0 120 S Max. Time 10 S 60 S Max. 360 Sec. Max. Specifications subject to change without notice. DATA SHEET #: Cx061 PAGE 2 OF 2 REV: 01 DATE: 01/16/08 aCopyright 2008 Connor-Winfield all rights reserved.