Intersil EL2018 Fast, high voltage comparator with transparent latch Datasheet

T
NT
DUC
PRO LACEME at
E
T
E
P
er
L
t
E
O
n
R
e
S
OB
DED upport C om/tsc
N
E
S
MM
l.c
ECO echnical w.intersi
T Sheet
NO R Data
w
r
w
u
December 1995, Rev. G
r
o
IL o
act
cont -INTERS
1-888
®
Fast, High Voltage Comparator with
Transparent Latch
The EL2018 represents a quantum
leap forward in comparator speed,
accuracy and functionality.
Manufactured with Elantec's proprietary Complementary
Bipolar process, this device uses fast PNP and NPN
transistors in the signal path. A unique circuit design gives
the inputs the ability to handle large common mode and
differential mode signals, yet retain high speed and excellent
accuracy. Careful design of the front end insures the part
maintains speed and accuracy when operating with a mix of
small and large signals. The three-state output stage is
designed to be TTL compatible for any power supply
combination, yet it draws a constant current and does not
generate glitches. When the output is disabled, the supply
current consumption drops by 50%, but the input stage and
latch remain active.
Elantec facilities comply with MIL-I-45208A and other
applicable quality specifications. For information on Elantec's
processing, see QRA1: Elantec's Processing-Monolithic
Products.
EL2018
FN7024
Features
• Fast response time—20ns
• Wide input differential voltage range—24V to ±15V
supplies
• Precision input stage—VOS = 1mV
• Low input bias current—IB = 100nA
• Low input offset current—IOS = 30nA
• ±4.5V to ±18V supplies
• Three-State TTL and CMOS compatible output
• No supply current glitch during switching
• High voltage gain—40V/mV
• 50% power reduction in shutdown mode
• Input and latch remain active in shutdown mode
• P/N compatible with industry standard comparators
Applications
• Analog to digital converters
• ATE pin receiver
• Precision crystal oscillators
Ordering Information
PART
NUMBER
EL2018CN
• Zero crossing detector
TEMP.
RANGE
PACKAGE
PKG. NO.
• Window detector
-40°C to +85°C
8-Pin PDIP
MDP0031
• Pulse width modulation generator
• “Go/no-go” detector
Pinout
EL2018
(8-PIN PDIP)
TOP VIEW
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2003. All Rights Reserved. Elantec is a registered trademark of Elantec Semiconductor, Inc.
All other trademarks mentioned are the property of their respective owners.
EL2018
Absolute Maximum Ratings (TA = 25°C)
VS
VIN
VIN
IIN
IINS
PD
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .±18V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . +VS to -VS
Differential Input Voltage . . . . Limited only by Power Supplies
Input Current (Pins 1, 2 or 3) . . . . . . . . . . . . . . . . . . . . ±10mA
Input Current (Pins 5 or 6) . . . . . . . . . . . . . . . . . . . . . . . ±5mA
Maximum Power Dissipation . . . . . . . . . . . . . . . . . . . . .1.25W
IOP
IO
TA
TJ
TST
Peak Output Current . . . . . . . . . . . . . . . . . . . . . . . . . . . 50mA
Continuous Output Current . . . . . . . . . . . . . . . . . . . . . . 25mA
Operating Temperature Range . . . . . . . . . . . .-40°C to +85°C
Operating Junction Temperature
Plastic DIP Package . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Storage Temperature . . . . . . . . . . . . . . . . . .-65°C to +150°C
The maximum power dissipation depends on package type, ambient
temperature and heat sinking. See the Typical Performance curves for more
details.
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: TJ = TC = TA
DC Electrical Specifications
PARAMETER
VOS
IB
IOS
CMRR
VS = ±15V unless otherwise specified
DESCRIPTION
TEMP
Input Offset Voltage (Note 1)
VCM = 0V, VO = 1.4V
MIN
25°C
TYP
MAX
UNITS
1.0
5
mV
7
mV
400
nA
600
nA
150
nA
250
nA
TMIN, TMAX
Input Bias Current
VCM = 0V, Pin 2 or 3
25°C
100
TMIN, TMAX
Input Offset Current
VCM = 0V
25°C
30
TMIN, TMAX
25°C
85
TMIN, TMAX
80
25°C
85
TMIN, TMAX
77
25°C
±12
TMIN, TMAX
±12
25°C
15
TMIN, TMAX
10
25°C
-0.05
TMIN, TMAX
-0.1
VS = ±15V
25°C
3.5
VS = ±15V
TMIN, TMAX
3.5
VS = ±5V
25°C
2.4
V
VS = ±5V
TMIN
2.4
V
VS = ±5V
TMAX
2.4
V
VS = ±15V
25°C
4.65
V
VS = ±15V
TMIN, TMAX
4.65
V
VS = ±5V
25°C
VODIS2
VOUT Range, Disabled, IOL = 1 mA, VS = ±5V to ±15V
ALL
-0.3
VINH
LE or CS Inputs
Logic High Input Voltage
25°C
2.0
V
TMIN, TMAX
2.2
V
PSRR
VCM
AV
VOL
VOH
VODIS1
Common Mode Rejection Ratio (Note 2)
Power Supply Rejection Ratio (Note 3)
Common Mode Input Range
Voltage Gain
VOUT = 0.8V to 2.0V
Output Voltage Logic Low
IOL = 0mA to 8mA
Output Voltage Logic High
VOUT Range, Disabled, IOL = -1mA
2
105
dB
dB
100
dB
dB
±13
V
V
40
V/mV
V/mV
0.15
4.0
0.4
V
0.4
V
4.65
V
4.65
V
3.5
V
-1
V
EL2018
DC Electrical Specifications
PARAMETER
VINL
IIN
IS+EN
IS+DIS
IS-EN
IS-DIS
VS = ±15V unless otherwise specified (Continued)
DESCRIPTION
LE or CS Inputs
Logic Low Input Voltage
LE or CS Inputs
Logic Input Current, VIN = 0V to 5V
Positive Supply Current
Enabled
TEMP
MIN
TYP
MAX
UNITS
25°C
0.8
V
TMIN, TMAX
0.8
V
25°C
±200
µA
TMIN, TMAX
±300
µA
12
mA
13
mA
6
mA
7
mA
17
mA
18
mA
6.5
mA
6.5
mA
25°C
8.4
TMIN, TMAX
Positive Supply Current
Disabled
25°C
4.7
TMIN, TMAX
Negative Supply Current
Enabled
25°C
13.0
TMIN, TMAX
Negative Supply Current
Disabled
25°C
5.0
TMIN, TMAX
NOTES:
1. VOUT = 1.4V.
2. VCM = 12V to -12V.
3. VS = ±5V to ±15V.
AC Electrical Specifications
PARAMETER
VS = ±15V, TA = 25°C
DESCRIPTION
MIN
TYP
MAX
UNITS
TPD
Propagation Delay, 5mV Overdrive
20
40
ns
TS
Setup Time
6
12
ns
TH
Hold Time
-2
0
ns
TUN
Unlatch Time
23
40
ns
TMPW
Minimum Clock Pulse Width
12
TEN
Output Three-State Enable Delay
40
70
ns
TDIS
Output Three-State Disable Delay
150
300
ns
3
ns
EL2018
Typical AC Performance Curves
4
Propagation Delay (-)
5mV Overdrive
Propagation Delay
vs Overdrive
Propagation Delay vs
Load Capacitance
Propagation Delay
vs Temperature
Propagation Delay
vs Input Step
Enabled/Disabled Time
vs Temperature
EL2018
Typical AC Performance Curves
(Continued)
Input Bias Current vs
Differential Input Voltage
Input Bias Current
vs Temperature
Open-Loop Gain
vs Frequency
CMRR vs Frequency
VO/VI Transfer
Characteristic
VOUT vs Temperature
5
EL2018
Typical AC Performance Curve
(Continued)
VOH vs Positive
Supply Voltage
VOL vs Positive
Supply Voltage
Supply Current
vs Temperature
Supply Current
vs Supply Voltage
8-Pin Plastic DIP
Maximum Power Dissipation
vs Ambient Temperature
6
EL2018
Block Diagram
Function Table
INPUTS
(TIME N-1)
+IN
-IN
CS
LE
INTERNAL
Q
+
-
+
L
L
L
L
H
L
Normal Comparator Operation
+
-
+
H
H
L
L
H
L
Internal Normal Comparator Operation
Output Power Down Mode
High Z
High Z
X
X
X
X
L
H
H
H
Qn-1
Qn-1
Data Retained in Latch
Data Retained in Latch
Power Down Mode
Qn-1
High Z
NOTES
Application Hints
Device Overview
The EL2018 is the first comparator of its kind. It is capable of
24V differential signals, yet has excellent accuracy, linearity
and voltage gain. It even has a three-state output feature that
reduces the power supply currents 50% when the output is
disabled, yet the input stage and latch remain active. This
extremely fast and accurate device is built with the
proprietary Elantec Complementary Bipolar Dielectric
Isolation Process, which is immune to power sequencing
and latch up problems.
Power Supplies
The EL2018 will work with ±5V to ±18V supplies or any
combination between (Example +12V and -5V). The
supplies should be well bypassed with good high frequency
capacitors (0.1µF monolithic ceramic recommended) close
to the power supply leads. Good ground plane construction
techniques enhance stability, and the lead from pin 1 to
ground should be short.
Front End
The EL2018 uses schottky diodes to make a “bullet proof”
front end with very low input bias currents, even if the two
inputs are tied to very large differential voltages (±24V). The
transfer function of the EL2018 is linear, and the output is
stable when in the linear region.
7
OUTPUT
H
L
The large common mode range (±12V minimum) and
differental voltage handling ability (±24V min.) of the device
make it useful in ATE applications without the need for an
input attenuator with its associated delay.
Recovery from Large Overdrives
Timing accuracy is excellent for all signals within the
common mode range of the device (±12V with ±15V supply).
When the common mode range is exceeded the input stage
will saturate, input bias currents increase and it may take as
much as 200ns for the device to recover to normal operation
after the inputs are returned to the common mode range. If
signals greater than the common mode range of the device
are anticipated, the inputs should be diode clamped to
remain within the common mode range of the device.
Input Slew Rate
All comparators have input slew rate limitations. The EL2018
operates normally with any input slew rate up to 300V/µs.
Input signal slew rates over 300V/µs induce offset voltages
of 5mV to 20mV. This induced offset voltage settles out in
about 20ns, 20 times faster than previous high voltage
comparators.
Latch
The EL2018 contains a “transparent” latch. A “transparent”
latch acts as an amplifier when the LE input is low and it
“latches” and holds the value it had just before the LE
transition from low to high.
EL2018
It is possible to make an oscillation resistant design by
putting a short duration “0” on the LE input whenever you
wish to make a comparison. This gates the comparator on
only for a brief instant, long enough to compare, but not long
enough to oscillate. The minimum duration of this pulse is
specified by the minimum clock width parameter in the AC
electrical tables.
The CS input may be left floating and still produce a
guaranteed logic “0” input (active). Floating the LE input will
normally produce a logic “0” input also, but operation is not
guaranteed.
Proper RF technique suggests that these inputs be
grounded or pulled to ground if they are not used.
Output Stage
The output stage of the EL2018 is a pair of complementary
emitter followers operating as a linear amplifier. This makes
the output stage of the EL2018 glitch free, and improves
accuracy and stability when operating with small signals.
Three-State Output, Power Saving Feature
The EL2018 has an output stage which can be put into a
high impedance “three-state” mode. When it is in this mode,
the input stage and latch remain active, yet the device
dissipates only 50% of the power used when the output is
active. This has advantages in a large ATE system where
there may be 1000 comparators, but only 10% are in use at
any one time.
8
Due to the power saving feature and linear output stage, the
EL2018 does not have a standard TTL three-state output
stage. As such one must be careful when using the threestate feature with devices other than other EL2018s or
EL2019s. When operating from ±15V supplies the threestate feature is compatible with all TTL families, however
CMOS families may conflict on high outputs. Since the
output stage of the EL2018 turns on faster than it turns off, a
50Ω to 100Ω resistor in series with the output will limit fault
currents between devices with minimum impact on logic
drive capability.
System Design Considerations
The most common problem users have with high speed
comparators is oscillations due to output to input feedback.
This can be avoided by using a ground plane, proper supply
bypassing, and routing the inputs and outputs away from
each other. Since the EL2018 has a gain bandwidth product
of about 40GHz, layout and bypassing are important to a
successful system design. A unique alternative to the
EL2018 is the EL2019, with its edge triggered master/slave
flip flop.
Device Functions
The various operating states of the EL2018 are described in
the function table on page 7.
EL2018
Typical Applications
USING THE POWER DOWN/
THREE-STATE FEATURE POWER
DISSIPATION VS AMBIENT
TEMPERATURE
SERIES RESONANT
CRYSTAL OSCILLATOR
A WIDE INPUT RANGE WINDOW COMPARATOR
USING THE EL2018 IN THE
TRANSPARENT MODE
(LATCH NOT USED)
VIN range +12V to -12V
with VS = ±15V
9
EL2018
Equivalent Schematic
Burn-In Circuit
PIN NUMBERS ARE FOR DIP PACKAGES.
ALL PACKAGES USE THE SAME SCHEMATIC.
10
EL2018
EL2018 Macromodel
* Connections: +input
*
|
-input
*
|
|
+V
*
|
|
|
-V
*
|
|
|
|
LE
*
|
|
|
|
| CS
*
|
|
|
|
| |
output
*
|
|
|
|
| |
|
.subckt M2018
2 3 8 4 6 5 7
*
* Input Stage
*
i1 8 10 700µA
r1 13 4 1K
r2 14 4 1K
q1 8 3 11 qn
q2 8 2 12 qn
q3 13 11 10 qp
q4 14 12 10 qp
i2 11 4 200µA
i3 12 4 200µA
*
* 2nd Stage & Flip Flop
*
*i4 8 24 700µA
i4 8 24 1mA
q9 22 6 24 qp
q10 18 17 24 qp
v1 17 0 2.5V
q5 15 14 22 qp
q6 16 13 22 qp
r3 15 4 1K
r4 16 4 1K
q7 16 15 18 qp
q8 15 16 18 qp
*
* Output Stage
*
i7 8 35 2mA
s1 35 20 5 0 sw
d2 35 8 ds
i6 26 34 5mA
s2 34 4 5 0 sw
d3 34 26 ds
q19 8 20 21 qn 2
q20 4 19 7 qp 2
r8 21 7 60
r7 20 19 4K
q17 19 16 26 qn 5
q18 0 15 26 qn 5
q22 20 20 30 qn 5
EL2018 Macromodel
* Connections:IN+IN+IN+IN+IN+IN+IN+IN+INININININ
q23 19 19 30 qn 8
d1 0 19 ds
q21 0 17 19 qp
*
* Power Supply Current
*
11
EL2018
ips 8 4 4mA
*
* Models
*
.model qn npn (is=2e-15 bf=400 tf=0.05nS cje=0.3pF cjc=0.2pF ccs=0.2pF)
.model qp pnp (is=0.6e-15 bf=60 tf=0.3nS cje=0.5pF cjc=0.5pF ccs=0.4pF)
.model ds d(is=2e-12 tt=0.05nS eg=0.62V vj=0.58)
.model sw vswitch (von=0.4V voff=2.5V)
.ends
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
12
Similar pages